Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 KHz to 300 GHz, 1999 Australian communications Authority Radiocommunications (Electromagnetic RadiationHuman Exposure) Standard, 2003

Two-Way Radio

Users Guide
ANATAL ANNEX to Resolution No. 303 of July 2, 2002 Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300GHz and Attachment to resolution #303 from July 2, 2002 To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures. Portable Radio Operation and EME Exposure

KEM-PK14146

Model SX700 series
Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. Do NOT hold the antenna when the radio is IN USE. Holding the antenna affects the effective range. Body-Worn Operation To maintain compliances with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body when transmitting, always place the radio in a Motorola-supplied or approved clip, holder, holster, case or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF exposure guidelines. If you do not use one of the Motorola-supplied or approved body-worn accessories and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting.
Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as Intrinsically Safe. Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles (such as grain, dust or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are oftenbut not alwaysposted. Blasting Caps and Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted Turn off two-way radios. Obey all signs and instructions.

Operational Cautions

Control Buttons

Use to:

Use to: Turn radio on/off. Increase or decrease volume LED Indicator Light Use Push to Talk PTT to: Talk Save a setting Boost the radios power up to two watts Use to:
Scan to see if anyone is on the selected channel Use
Select Menu options Exit the Menu (when pressed while in a Menu) Hi Lo Lock and unlock the keypad (when held down and not in a Menu) Accessory Jack Use and + to: Scroll through menus Microphone
Antennas Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury such as burns if a conductive materiallike jewelry, keys or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse or other container with metal objects.
Using the Desk Stand Charger (Optional Accessory) The desk stand charger provides drop-in charging convenience for NiMH batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiMH battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours. 1. Follow the steps above to install a NiMH Battery Pack. 2. Plug the AC power supply into the plug on the desk stand. 3. Plug the AC power supply into a standard wall outlet. 4. Remove the battery pocket inserts from the charger pockets. 5. With a radio facing forward, slide it into one of the charging pockets. Notes The light on the AC power supply will glow continuously when radio/battery is inserted. When moving between hot and cold temperatures, do not charge the battery until the battery temperature acclimates (usually about 20 minutes). For optimal battery life, remove the radio or battery from the charger within 16 hours. Do not store the radio in the charger. Turn radio off while in charging tray.

Using the Belt Holster Your radio includes a holster so you may carry it easily on your belt. 1. Adjust the holsters clip so it fits onto your belt. 2. Slide your radio into the holster. Turning Your Radio On and Off Turn clockwise to turn the radio on and counterclockwise to turn the radio off. 1. The radio chirps and briefly shows all features icons available on your radio. 2. The display then shows the current channel, code and features that are selected. Setting the Volume Press and hold listening level.
Channels and Frequencies Channel Frequency Description Channel Frequency Description 11 462.5625 MHz 462.5875 MHz 462.6125 MHz 462.6375 MHz 462.6625 MHz 462.6875 MHz 462.7125 MHz 467.5625 MHz 467.5875 MHz 467.6125 MHz 467.6375 MHz GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS FRS FRS FRS FRS 22 467.6625 MHz 467.6875 MHz 467.7125 MHz 462.5500 MHz 462.5750 MHz 462.6000 MHz 462.6250 MHz 462.6500 MHz 462.6750 MHz 462.7000 MHz 462.7250 MHz FRS FRS FRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS
Transmit call tone Speaker

For More Information

For further information, you may call Motorola at 1-800-638-5119 (U.S. and Canada) or visit us on the Internet at http://www.motorola.com.
Data Operation If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least one inch (2.5 cm) from the body. Approved Accessories For a list of approved Motorola accessories, visit out Web site at www.Motorola.com. Electromagnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration.

People with pacemakers should: ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.
Battery Charger Safety Instructions: Save these Instructions 1. Do not expose the charger to rain or snow. 2. Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way. 3. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock. 4. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle. 5. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning. 6. Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock or personal injury. 7. Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress. 8. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:
The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger. The extension cord is properly wired and in good electrical condition. The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet. 9. The supply cord of this charger cannot be replaced. If the cord is damaged, call Motorola Product Services at 1-800-353-2729 in the USA or 1-888-390-6456 TTY (text telephone).

Display Screen Guide

while rotating

until you reach a comfortable
Interference Eliminator Code Interference Eliminator Codes help minimize interference by providing you with a choice of code combinations. Your radio has 121 Interference Eliminator Codes. Codes are the standard codes that appear on other FRS/GMRS radios. Codes are additional codes added for superior interference protection. To set the code for a channel: 1. Short press until the code starts to flash. 2. Press + or to select the code. 3. Press PTT to save the code setting or to continue set up.

MENU MENU

Numbers for Channel, Call Tone

1. Rotate 2. Rotate

clockwise to increase the volume counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

Numbers for Codes

Talking and Listening
You can set a different code for each channel using this procedure. An extended press of + or allows you to scroll through the Interference Code rapidly so you can quickly reach the code you want. Note: You must set the Interference Eliminator Code to 0 on a radio that uses Interference Eliminator Codes to communicate with radios that do not have Interference Eliminator Codes. Select 0 for no tone, no code and OFF will flash on your radios display. Setting and Transmitting Call Tones Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. You have 10 call tones from which to choose. To set a call tone: 1. With the radio on, short press until the current call tone setting flashes and appears. 2. Press + or to change and hear the call tone. 3. Press PTT to set the new call tone or to continue set up.
Battery Meter 2 watt Channel Indicator .5 watt channel indicator (see Initial Set Up) Lock
On/Off for each feature Vibrate Scan Call Tone, Keypad Tone Weather Alert
To communicate, all radios in your group must be set to the same channel and Interference Eliminator Code. 1. To talk, press and hold PTT. 2. When you are finished talking, release PTT. For maximum clarity, hold the radio two to three inches away from your mouth and speak directly into the microphone. Do not cover the microphone while talking. Talk Range Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than five feet apart. Power Boost To boost your radios power up to two watts, press the top portion of the PTT button when talking. If you know your party is close by, you can conserve your batterys energy by pushing the lower part of the PTT button to use less power.

Call Tone Confirmation (Roger Beep)

i VOX Hands-Free Use

Without Accessories
To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press. Note: Setting the call to 0 disables the call tone feature.

Noise Filtering

Safety and General Information
Important Information on Safe and Efficient Operation
FCC Licensing Information
Your Motorola radio operates on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please request Form 605 and 159, which includes all of the forms and instructions you will need. If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information: For a Fax: Contact the Fax-On Demand system 1-202-418-0177 For Mail Service: Call the FCC Forms Hotline 1-800-418-FORM (3676) If You Have Questions about the FCC License: Call the FCC 1-888-CALL-FCC (225-5322)

Getting Started

Installing the Batteries: Your radio uses four AAA Alkaline batteries and beeps when the batteries are low. 1. Turn the radio off. 2. With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover. 3. Insert four AAA Alkaline batteries as shown on the inside of the battery compartment. 4. Reposition the battery cover and press down to secure. NOTE: The SX700 model radio can use a NiMH rechargeable battery instead of four AAA batteries. Installing the NiMH Battery Pack: 1. Follow step 1 and 2 above to remove the battery cover. 2. Remove the battery pack from the clear plastic bag. Do not disassemble or unwrap the battery pack. 3. Insert the NiMH battery pack so the This Side Up is showing. 4. Reposition the battery cover and press down to secure. Battery Meter The battery icon shows the battery charge level, from full to empty. When the battery is empty, the radio chirps periodically after releasing PTT. The radio powers off when the voltage drops below a predetermined level to protect the rechargeable battery. Note: Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio.
Note: If you are on an FRS only channel (see channel and frequencies chart) the radio will only use lo power when either portion of the PTT is pressed. Monitor Button Pressing and holding MON for three seconds allows you to listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. You can also press MON to check for activity on the current channel before you talk. Push to Talk PTT Timeout Timer To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press PTT for 60 continuous seconds.

Hands-Free Use Without Accessories (iVOX) You can use the iVOX feature to transmit, hands-free without the need for any voice activation accessories. Once iVOX is turned on, the radio detects your voice and transmits when you speak. 1. Short press until iVOX appears on the display. The current setting On/Off will flash. 2. Press + or to select On or Off. 3. Press PTT to set or to continue set up.
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002. Transmit and Receive Procedure Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/uncontrolled environment exposure limits, always adhere to the following procedure: Transmit no more than 50% of the time. To receive calls, release the PTT button. To transmit (talk), press the Push to Talk (PTT) button. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). Exposure to Radio Frequency Energy Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: United States Federal communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Medical Devices Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Safety and General Use While Driving Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please:
Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.

Setting the Sensitivity Level When in VOX or iVOX Mode Adjusting the radios sensitivity level helps minimize the possibility of unintended noises triggering a transmission and helps the radio pick up soft voices. 1. Short press after setting iVOX. VOX will still appear. 2. Press + or to select the sensitivity level.

Initial Setup

Selecting the Channel Your radios has 22 channels. Channels 8-14 are FRS 0.5 Watt only and all other channels are GMRS. When you press the bottom portion of the PTT all channels are 0.5 Watt. If you press the top portion of the PTT to boost the power GMRS channels will be 2 Watt. Note: When on FRS only channel top or bottom press of PTT will only be 0.5Watt. 1. With the radio on, press 3. Press. The current channel flashes. 2. Press + or to set the channel.
You may also visit the FCCs Web site at http://www.fcc.gov. Changes or modifications not expressly approved by Motorola may void the users authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the provide land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules. Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
3 = High Sensitivity for quiet environments 2 = Medium Sensitivity for most environments 1 = Low Sensitivity for noisy environments Note: When you connect a VOX accessory, the radio is automatically set to the last chosen sensitivity level. See Special Features section on Accessories.
to save the channel setting or

to continue set up.

Continued on back SX700
VibraCall Alert VibraCall is a vibrating alert that notifies you that your radio is receiving a message. This is useful in noisy environments. When the alert is on, the radio vibrates once every 30 seconds when you receive a message on the channel and code you set. 1. To turn vibrating alerts on, press until is displayed. The current setting will flash. 2. Press + or to change the setting to Off/On. 3. Press PTT to set or to continue set up.

Special Features

Keypad Lock To avoid accidentally changing your radio settings: 1. Press and hold until displays. 2. When in lock mode, you can turn the radio on and off, adjust the volume, receive, transmit, send a call tone, and monitor channels. All other functions are locked. To unlock the radio, press and hold until is no longer displayed.

QT Noise Filtering The QT noise-filtering feature helps to ensure uninterrupted communication with other Motorola radios that have this feature. This feature filters out unwanted transmissions from other radios. This is useful in places where there is heavy radio traffic, such as amusement parks or ski resorts. Note: QT noise filtering is not available when the radio is scanning. To turn QT noise filtering on or off: 1. Short press until QT displays. The current setting On/Off will flash. 2. Press + or to turn noise filtering On or Off. 3. Press PTT to confirm your selection or to continue set up.
To transmit to a radio that has QT noise filtering turned on: 1. Select the same channel and Interference Eliminator Code as the other radio. 2. Press to send a call tone. This allows your voice to pass through the QT noise filter on the receiving radio. 3. Press
Enhanced Scanning Use scanning to monitor channels and codes for transmissions or to find someone in your group who has accidentally changed channels. With enhanced scanning, your home channel is scanned more frequently than any other channel. The home channel is the channel where your radio was set when you started to scan. If you activate scan while your radios Interference Eliminator Code is set to a number between 1 and 121, the radio checks for activity on each channelbut only in the specific code selected. All transmissions using code 0 or any other code are ignored. 1. To start scanning, briefly press and release MON. The scan indicator displays , and the radio begins to scroll through the channel and Interference Eliminator Code combinations. 2. When the radio detects channel activity, it stops scanning and you can hear the transmission. 3. To respond and talk to the person transmitting, press PTT within five seconds. 4. To stop scanning, briefly press and release MON.
Weather Your radio can tune in to broadcasts by the United States National Oceanic and Atmospheric Administration (NOAA) Weather Radio and Environment Canada Weatheradio. You can listen to a weather channel or set your radio to alert you to emergency weather broadcasts that interrupt routine broadcasts. When you listen to a weather channel, you cannot use your radio in scan mode or for two-way communications. Both NOAA and Environment Canada have transmitters located throughout the United States and Canada, respectively. These transmitters broadcast watches, forecasts, and other information 24 hours a day. Weather Channels and Frequencies Weather Channel WX1 WX2 WX3 WX4 WX5 WX6 Frequency 162.550 MHz 162.400 MHz 162.475 MHz 162.425 MHz 162.450 MHz 162.500 MHz Weather Channel WX7 WX8 WX9 WX10 WX11 Frequency 162.525 MHz 161.650 MHz 161.775 MHz 161.750 MHz 162.000 MHz

Note: NOAA weather radio stations are assigned to cover specific areas and service may be limited. Please check with your local weather office for frequency and details, or visit www.nws.noaa.gov/nwr in the US or www.msc-smc.ec.gc.ca/cd/factsheets/wxradio in Canada to view the appropriate transmitter for your area. The use of the NOAA logo does not provide an endorsement or implied endorsement by NOAAs National Weather Service, nor does the use of the Weatheradio logo provide an endorsement or implied endorsement by Environment Canada. Turning Weather Channel Reception On and Off 1. To turn weather reception on, press and hold + for three seconds. 2. To turn off, press + or turn the radio off and then back on. Setting the Weather Channel Your radio receives weather frequencies: 1. After turning weather reception on, press. The current channel flashes. 2. Press + or to select the channel. 3. Press PTT to save the weather channel setting.

and speak normally.

Note: If you skip step 2, the beginning of your message may not be heard on the receiving radio. For a 30-second period, starting after the last transmission, all transmissions received on the selected channel and code will pass through the QT noise filter. Keypad Tones You may enable or disable the speaker key tones. You will hear the key tone each time a button is pushed. 1. Press until appears. The current setting On/Off will flash 2. Press either + or to turn On or Off. 3. Press PTT to confirm or to continue set up.
Note: If you press PTT while the radio is scanning, the radio will transmit on the channel you selected before you activated scan. If no transmission occurs within five seconds, scanning will resume. Advanced Scan If the radio stops scanning on a channel you do not want to listen to, briefly press and release + or to resume scanning for the next active channel. Removing Channels from the Scan List (Nuisance Delete Feature) 1. To prevent the radio from scanning a channel, press and hold + or for at least three seconds, then release, when the scan first stops on that channel. This temporarily removes the channel from the scan list. 2. Press MON to exit scan mode. 3. Press
Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage.

B. Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CD-ROM, or floppy disk).
B. Ninety (90) days from the date of purchase.
Software Embodied in Physical Media. No warranty is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided as is and without warranty.
When the Key Tone Feature is off, the following are not disabled: Transmit timeout alert tone; Power-down alert tone; Low battery alert tone; or The transmitted Talk Confirmation Tone. Transmitting a Talk Confirmation Tone You can set your radio to transmit a unique tone when you finish transmitting. It is like saying Roger or Over to let others know you are finished talking. 1. With the radio on, press until the appears. The current setting On/Off flashes. 2. Press + or to turn On or Off. 3. Press PTT to set or to continue set up.
a second time to activate scan again.
4. To restore a previously deleted channel, turn the radio off and then back on. The channel is now restored. Note: You cannot remove your home channel from the scan list. The home channel is the channel your radio was set to when you started the scanning. Using Audio Accessories: Many accessories (sold separately) are available for your radio. For more information, visit our Web site at www.motorola.com. Hands-Free Use With Accessories (VOX) You can transmit hands-free with the use of optional accessories. Once VOX is turned on, the radio detects your voice and transmits when you speak. 1. Turn the radio off and plug the VOX accessory into the accessory port. 2. Turn the radio on. VOX shows on the display. 3. Adjust the volume appropriately by rotating. Lower the volume before placing the accessory on your head or in your ear. 4. To turn off, simply remove accessory. Note: There is a short delay between the time you start talking and when the radio transmits. There is a short delay before the transmission is completed.

Setting the Weather Alert Your radio receives weather frequencies: 1. After turning weather reception on, press
Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable. twice. Off/On displays. What will GIANT INTERNATIONAL LTD. Do? GIANT INTERNATIONAL LTD., at its option, will at no charge repair, replace or refund the purchase price of any Products, Accessories or Software that does not conform to this warranty. We may use functionally equivalent reconditioned/refurbished/pre-owned or new Products, Accessories or parts. No data, software or applications added to your Product, Accessory or Software, including but not limited to personal contacts, games and ringer tones, will be reinstalled. To avoid losing such data, software and applications please create a back up prior to requesting service. How to Obtain Warranty Service or Other Information? To obtain service or information, please call:
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
2. Press + or to select Off/On. If you activate Weather Alert and return to two-way mode, will display. 3. Press
to save the weather channel setting.
As with two-way radio reception, weather channel reception depends on how close you are to a transmitter and whether you are indoors or outdoors. Because weather channels are transmitted without codes, they may contain static or noise.

USA Two-Way Radios

1-800-638-5119

Canada Two-Way Radios

Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official licensee for this product. Motorola, the Motorola logo trademarks and the Motorola trade dress are owned by Motorola, Inc. and are used under license from Motorola, Inc. Please contact Giant International Ltd. at 800-638-5119 for questions/comments, warranty, support, or service related to this product. MOTOROLA and the Stylized M Logo are registered in the U.S. Patent & Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. 2005.

For Accessories and Software, please call the telephone number designated above for the product with which they are used. You will receive instructions on how to ship the Products, Accessories or Software, at your expense, to a GIANT INTERNATIONAL LTD. Authorized Repair Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number.
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one jurisdiction to another. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted Motorola software such as the exclusive rights to reproduce and distribute copies of the Motorola software. Motorola software may only be copied into, used in, and redistributed with, the Products associated with such Motorola software. No other use, including without limitation disassembly of such Motorola software or exercise of the exclusive rights reserved for Motorola, is permitted.

S E R I E S

P R O D U C T S P E C S AT A G L A N C E
With a range of up to 12 miles*, the Talkabout SX700 series uses both FRS and GMRS frequencies, providing more channels.

S X 0 F E AT U R E S :

M O T O R O L A TA L K A B O U T S X 0 T W O -WAY R A D I O S E R I E S
The Motorola Talkabout SX700 is the ultimate communication tool for the serious outdoor enthusiast. With a range of up to 12 miles* and loaded with every possible radio feature, you know that with the SX700 you are ready for the extreme outdoors. Lightweight and rugged, with side grips to help you hold on, and a holster to provide you with quick access, the SX700 is built to handle any challenge without weighing you down.
N O A A W E AT H E R C H A N N E L
2.0 watt power delivers a range of up to 12 miles* 22 channels, each with 121 privacy codes for 2,662 combinations 10 hr. alkaline or 7 hr. NiMH estimated talk time iVOX hands-free communication without the need of an audio accessory NOAA weather alert feature QT (Quiet Talk) interruption feature Companding technology Backlit display LCD battery meter Battery save feature VibraCall vibrating alert
Want to know where the best conditions are for your rock climbing outing? Tune into a NOAA channel (National Oceanic and Atmospheric Administration) on your SX700 for continuous local and regional weather broadcasting. And when you are out having fun, weather alerts will provide you with warnings of incoming weather to protect from the dangers of a sudden storm.
F U L L- F E AT U R E D P R I V A C Y
All models include these core features:
Audible low battery alert Keypad lock 10 call tones Time-out timer Priority scan
To prevent cluttered channels, the SX700 has a full 22-channel capacity each with 121 privacy codes, creating 2,662 combinations. Additionally, Priority scan quickly finds the most private channel in crowded environments, and with the QT (Quiet Talk) interruption filter enabled, radios from other manufacturers cant be heard on your channel ensuring a private conversation for your group.
H A N D S - F R E E C O M M U N I C AT I O N

SERIES MODELS

SX700R
Includes 2 radios, 2 drop-in chargers, 2 charging adapters, 2 NiMH rechargeable battery packs and 1 set of Black faceplates. Available in Bronze.
In the middle of a mountain bike trail you really dont want to take your hands off the handlebars. Enter iVOX. Acting as a speakerphone, the iVOX hands free communication allows you to use your hands for other activities while keeping in touch.

SILENT SIGNALS

The VibraCall silent vibrating ringer is especially useful for locations where ringing can be intrusive. This feature is also great when noise from a sporting event would drown out your ring tone.

C O M PA N D I N G

The SX700 has a Motorola exclusive feature companding a sophisticated digital technology that filters out static between words. This allows the radio to deliver noticeably clearer transmission.
SX700R Radio Dimensions: 7.8 X 2.4 X 1.3 inches Packaging Dimensions: 15.3 X 10.6 X 4.4 inches Overpack Dimensions: 18 X 16.4 X 10.6 inches Radio Weight w/o Batteries:.24 lbs Packaged Weight w/ Contents: 3 lbs Overpack Weight: 12.5 lbs Overpack Quantity: 4 UPC Number: UCC Number: 9

PRICING

Manufacturers Suggested Retail Price is $79.99 (NiMH) per pair.
*How far can I expect my radios to communicate? The communication range quoted is calculated under optimum conditions, with an unobstructed line of sight. Actual range will vary depending on terrain and conditions, and is often less than the maximum possible. Your actual range will be limited by several factors including, but not limited to, terrain, weather conditions, electromagnetic interference, and obstructions. Please visit www.giantintl.com/range for further information. MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office.