Motorola T8510 Manual
Motorola T8510, size: 9.8 MB
Here you can find all about Motorola T8510 like manual and other informations. For example: .
Motorola T8510 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Motorola T8510 please write about it to help other people. [ Report abuse or wrong photo | Share your Motorola T8510 photo ]
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
ANATAL ANNEX to Resolution No. 303 of July 2, 2002 Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300GHz and Attachment to resolution #303 from July 2, 2002. To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures. Portable Radio Operation and EME Exposure Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. Do NOT hold its antenna when the radio is IN USE. Holding the antenna affects its effective range. Body-Worn Operation To maintain compliances with FCC/Health Canada RF exposure guidelines if you wear a radio on your body when transmitting always place the radio in a Motorola-supplied or approved clip holder, holster, case or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF exposure guidelines.
Use to: Turn radio on/off Increase or decrease volume
Use Monitor MON to: Scan to see if anyone is on other channels Monitor the selected channel for activity Use
Removing the Three AA Batteries 1. Turn the radio off. 2. With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover. 3. Gently remove each battery by easing each battery out individually. 4. Reposition the battery cover and press down to secure. Notes Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries. Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio. Using the Battery Charger The battery charger provides drop-in charging convenience for NiMH batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiMH battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours. 1. Follow the steps above to install a NiMH Battery Pack. 2. Plug the AC power supply cord into the jack on the desk stand. 3. Plug the AC power supply into a standard wall outlet. 4. With a radio facing forward, slide it into one of the charging pockets. Notes The red light on the charging base will glow continuously to indicate the radio is correctly inserted and charging. The light will remain red after the battery pack is fully charged. When moving between hot and cold temperatures, do not charge the battery until the battery temperature acclimates (usually about 20 minutes). For optimal battery life, remove the radio or battery from the charger within 16 hours. Do not store the radio in the charger. Turn radio off while in charging tray. Attaching and Removing the Belt Clip 1. Attach belt clip to pocket or belt strap. 2. Align the belt clip post with the hole in the back of the radio. 3. Gently push until the clip clicks in place. To Remove 1. Push down on the release tab at the top of the belt clip to release the catch. 2. Pull the belt clip away from the back of the radio.
Selecting the Channel Your radio has 22 channels. Channels 8-14 are FRS 0.5 watt only and all other channels are GMRS (See the "Channels and Frequencies" table on overleaf for details). 1. With the radio on, press. When the radio is on a 0.5 watt channel, displays. When the radio is on a 1 watt channel, displays. The current channel flashes.
2. Press + or and select an unused or quiet channel. 3. Press
Use Push to Talk PTT to: Talk Save a setting
to save the channel setting or
to continue set up.
Select Menu options Exit the Menu (when pressed while in a Menu) Lock and unlock the keypad (when held down and not in a Menu) Accessory Jack Use and + to: Scroll through menus Turn weather on/off Microphone
Selecting The Interference Eliminator Code Interference Eliminator Codes help minimize interference by blocking transmissions from unknown sources. Your radio has 121 Interference Eliminator Codes. Codes are the standard analog codes that appear on other FRS/GMRS radios. Codes are additional digital codes added for superior interference protection. 0 is the off position, no analog or digital codes are enabled. To set the code for a channel: 1. Press until the code starts to flash. 2. Press + or to select the code. 3. Press PTT to save the code setting or
Transmit call tone
Model T8500/T8510/ T8530/T8550 series
If you do not use one of the Motorola-supplied or approved body-worn accessories and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting. Data Operation If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least one inch (2.5 cm) from the body. Approved Accessories For a list of approved Motorola accessories, visit our Web site at www.motorola.com. Electromagnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration.
You can set a different code for each channel using this procedure. An extended press of + or allows you to scroll through the Interference Code rapidly so you can quickly reach the code you want. Note: You must set the Interference Eliminator Code to 0 on a radio that uses Interference Eliminator Codes to communicate with radios that do not have Interference Eliminator Codes. Select 0 for no tone, no code and OFF will flash on your radios display. Setting and Transmitting Call Tones Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. You have 10 call tones from which to choose.
Display Screen Guide
To set a call tone:
1. With the radio on, press three times until the current call tone setting (0 - 10) flashes and appears. 2. Press + or to change and hear the call tone. 3. Press PTT to set the new call tone or to continue set up.
Turning Your Radio On and Off
To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press. Note: Setting the call to 0 disables the call tone feature. Hands-Free Use Without Accessories (iVOX) You can use the iVOX feature to transmit hands-free without the need for any headset accessories. Once iVOX is turned on, the radio detects your voice and transmits when you speak into the internal microphone. 1. Press until i VOX appears on the display. The current setting On/Off will flash. 2. Press + or to select On or Off. 3. Press PTT to set or to continue set up.
Battery Meter Channel Power Indicator (see Initial Set Up) Lock Talk Confirmation Tone (Roger Beep)
On/Off for OFF each feature Vibrate Scan Call Tone, Keypad Tone Weather Alert
Turn clockwise to turn the radio on and counterclockwise to turn the radio off. 1. In the ON position, the radio chirps and briefly shows all feature icons available on the radio. 2. The display screen then shows the current channel, code and all features that are enabled. Setting the Volume Press and hold MON for three seconds while rotating a comfortable listening level. 1. Rotate 2. Rotate clockwise to increase the volume. counterclockwise to decrease the volume. until you reach
For More Information
For further information, you may call Motorola at 1-800-638-5119 (U.S. and Canada) or visit us on the Internet at http://www.motorola.com.
i VOX Hands-Free Use
Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.
VOX Hands-Free Use
Hands-Free Use With Accessories (VOX) You can transmit hands-free more reliably with the use of optional headset accessories. Once VOX is turned on, the radio detects your voice and transmits when you speak. Many accessories (sold separately) are available for your radio. For more information, visit our Web site at www.motorola.com or http://shop.giantintl.com. 1. Turn the radio off and plug the VOX accessory into the accessory port. 2. Turn the radio on. VOX shows on the display. 3. Adjust the volume appropriately by rotating. Lower the volume before placing the accessory on your head or in your ear. 4. To turn off, simply remove accessory. Note: There is a short delay between the time you start talking and when the radio transmits. There is a short delay before the transmission is completed. Setting the Sensitivity Level When in VOX or iVOX Mode Adjusting the radios sensitivity level helps minimize the possibility of unintended noises triggering a transmission and helps the radio pick up soft voices. 1. Press until VOX and the level setting (1-3) appear on the display. 2. Press + or to select the sensitivity level. 3. Press PTT to set or to continue set up.
People with pacemakers should:
Safety and General Information
Important Information on Safe and Efficient Operation
ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place. Medical Devices Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Medical Devices Other If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Safety and General Use While Driving Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please: Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. The use of a two-way radio while engaged in activities requiring concentration may cause distraction or otherwise impair your ability to safely participate in such activities. Always use technology safely. Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable
Installing the Batteries Each radio uses 1 NiMH rechargeable battery pack or 3 AA Alkaline batteries and beeps when the batteries are low. Installing NiMH Rechargeable Battery Pack 1. Turn the radio off. 2. With the back of the radio facing you, lift the battery cover latch up and remove the cover. 3. Remove the battery pack from the clear plastic bag (Do not disassemble or unwrap the battery pack). 4. Insert the NiMH battery pack with the diagram facing you. 5. Reposition the battery cover and press down to secure. Installing the Three AA Alkaline Batteries 1. Turn the radio off. 2. With the back of the radio facing you, lift the battery cover latch up and remove the cover. 3. Insert the three AA Alkaline batteries with + and - polarity as shown inside the battery compartment. 4. Reposition the battery cover and press down to secure. Radio Battery Meter The radio battery icon shows the battery charge level, from full to empty. When the radio has one segment left, the radio chirps periodically or after releasing PTT (Low Battery Alert). Removing the NiMH Battery Pack 1. Turn the radio off. 2. With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover. 3. Gently remove the NiMH battery. 4. Reposition the battery cover and press down to secure.
Talking and Listening
To communicate, all radios in your group must be set to the same channel and Interference Eliminator Code. 1. To talk, press and hold PTT. 2. When you are finished talking, release PTT. For maximum clarity, hold the radio two to three inches away from your mouth and speak directly into the microphone. Do not cover the microphone while talking. Talk Range Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than five feet apart. Monitor Button Pressing and holding MON for three seconds allows you to listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. You can also press MON to check for activity on the current channel before you talk. Push to Talk PTT Timeout Timer To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press PTT for 60 continuous seconds.
FCC Licensing Information
Your Motorola radio operates on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please request Form 605 and 159, which includes all of the forms and instructions you will need. If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information: For a Fax: Contact the Fax-On Demand system For Mail Service: Call the FCC Forms Hotline If You Have Questions about the FCC License: Call the FCC
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002. Transmit and Receive Procedure Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/ uncontrolled environment exposure limits, always adhere to the following procedure: Transmit no more than 50% of the time. To receive calls, release the PTT button. To transmit (talk), press the Push to Talk (PTT) button. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). Exposure to Radio Frequency Energy Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J. American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992. Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999 Edition. International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998.
You may also visit the FCCs Web site at http://www.fcc.gov. Changes or modifications not expressly approved by Motorola may void the users authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules. Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
3 =High Sensitivity for quiet environments 2 =Medium Sensitivity for most environments 1 =Low Sensitivity for noisy environments
Note: When you connect a headset, the radio is automatically set to the last chosen sensitivity level.
Continued on back T8500/T8510/T8530/T8550
Menu Options (continued)
VibraCall TM Alert VibraCall is a vibrating alert that notifies you that your radio is receiving a message. This is useful in noisy environments. When the alert is on, the radio vibrates once every 30 seconds when you receive a message on the channel and code you set. 1. To turn vibrating alerts on, press until is displayed. The current setting will flash. 2. Press + or to change the setting to Off/On.
Keypad Lock To avoid accidentally changing your radio settings: 1. Press and hold until displays. 2. When in lock mode, you can turn the radio on and off, adjust the volume, receive, transmit, send a call tone, and monitor channels. All other functions are locked. To unlock the radio, press and hold until is no longer displayed.
Your radio can tune in to broadcasts by the United States National Oceanic and Atmospheric Administration (NOAA) Weather Radio and Environment Canada Weatheradio. You can listen to a weather channel (see Weather Channels and Frequencies table below) or set your radio to alert you to emergency weather broadcasts that interrupt routine broadcasts. When you listen to a weather channel, you cannot use your radio in scan mode or for two-way communications. Both NOAA and Environment Canada have transmitters located throughout the United States and Canada, respectively. These transmitters broadcast watches, forecasts, and other information 24 hours a day. Note: NOAA weather radio stations are assigned to cover specific areas and service may be limited. Please check with your local weather office for frequency and details, or visit www.nws.noaa.gov/nwr in the US or www.msc-smc.ec.gc.ca/cd/factsheets/wxradio in Canada to view the appropriate transmitter for your area. The use of the NOAA logo does not provide an endorsement or implied endorsement by NOAAs National Weather Service, nor does the use of the Weatheradio logo provide an endorsement or implied endorsement by Environment Canada. Turning Weather Channel Reception On and Off 1. To turn weather reception on, press and hold + for three seconds. 2. To turn off, press + or turn the radio off and then back on. Setting the Weather Channel Your radio receives weather frequencies: 1. After turning weather reception on, press. The current channel flashes. 2. Press + or to select the appropriate channel with good reception in your area.
Consumer Two-Way Radio Products and Accessories purchased in the United States or Canada.
What Does this Warranty Cover? Subject to the exclusions contained to the right, Giant International Ltd. warrants the Motorola branded consumer two-way radios that operate via Family Radio Service or General Mobile Radio Service that it manufactures (Products), the Motorola branded or certified accessories sold for use with these Products that it manufactures (Accessories) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumers exclusive remedy, and applies as follows to new Motorola branded Products and Accessories manufactured by Giant International Ltd., and purchased by consumers in the United States or Canada, which are accompanied by this written warranty:
Products Covered Products and Accessories as defined above, unless otherwise provided for below. 1. Decorative Accessories and Cases. Decorative covers and cases. 2. Monaural Headsets. Ear buds and boom headsets that transmit mono sound through a wired connection. 3. Consumer Two-Way Radio Accessories. 4. Products and Accessories that are Repaired or Replaced.
Length of Coverage One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below. 1. Limited lifetime warranty for the lifetime of ownership by the first consumer purchaser of the product. 2. Limited lifetime warranty for the lifetime of ownership by the first consumer purchaser of the product. 3. Ninety (90) days from the date of purchase by the first consumer purchaser of the product. 4. The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer.
Exclusions Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola or Giant International Ltd., are excluded from coverage. Use of Non-Motorola branded Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, Giant International Ltd. or its authorized service centers, are excluded from coverage. Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola branded housings, or parts, are excluded from coverage. Communication Services. Defects, damages, or the failure of Products or Accessories due to any communication service or signal you may subscribe to or use with the Products or Accessories is excluded from coverage.
to set or
QT Noise Filtering The QT noise-filtering feature helps to ensure uninterrupted communication with other Motorola radios that have this feature. This feature also filters out unwanted transmissions from other radios. This is useful in places where there is heavy radio traffic, such as amusement parks or ski resorts. Note: QT noise filtering is not available when the radio is scanning. To turn QT noise filtering on or off: 1. Press until QT displays. The current setting On/Off will flash. 2. Press + or to turn noise filtering On or Off. 3. Press PTT to confirm your selection or to continue set up.
Scanning Channels Use scan to search the 22 channels for transmissions from unknown parties, to find someone in your group who has accidentally changed channels, or to quickly find unused channels for your own use. There is a priority feature and 2 modes of scanning ( basic and advanced ) to make your search more effective. The basic scan mode uses the channel and code combinations for each of the 22 channels as you have set them ( or with the default code value of 1). The Advanced Scan mode will scan all channels for any and all codes, detect any code in use, and use that code value temporarily for that channel. Priority is given to the home channel, that is, the channel (and Interference Eliminator Code) your radio was set to when you start the scan. This means the initial channel (and code setting) is scanned more often than the other 21 channels, and your radio will respond quickly to any activity occurring on the home channel as a priority. To start Scanning: 1. Briefly press the MON key. The scan will appear in the display, and the radio will begin to scroll through the channel and code combinations. 2. When the radio detects channel activity matching the channel and code combination, it stops scrolling and you can hear the transmission. 3. To respond and talk to the person transmitting, press PTT within five seconds after the end of the transmission. 4. The radio will resume scrolling through the channels five seconds after the end of any received activity. 5. To stop scanning, briefly press the MON key. To start Advanced Scanning: 1. Set the Interference Eliminator Code to zero or OFF. 2. Briefly press the MON key. The scan will appear in the display, and the radio will begin to scroll through the channels. No Interference Eliminator Codes will filter what is heard. 3. When the radio detects channel activity with ANY code (or NO code), it stops scrolling and you can hear the transmission. Any Interference Eliminator Code that may be in use by that party will be detected and displayed. 4. To respond and talk to the person transmitting, press PTT within five seconds of the end of the transmission. The radio will transmit using the newly detected Interference Eliminator Code. 5. The radio will resume scrolling through the channels five seconds after the end of any received activity. 6. To stop scanning, briefly press the MON key. Scanning Notes: 1. If you press PTT while the radio is scrolling through inactive channels, the transmission will be on the home channel. Scanning will resume five seconds after the end of your transmission. You may press the MON key to stop scanning at any time. 2. If the radio stops on an undesired transmission, you may immediately resume the scan by briefly pressing + or . 3. If the radio repeatedly stops on an undesired transmission, you may temporarily remove that channel from the scan list by pressing and holding + or for three seconds. You may remove more than one channel in this way. 4. To restore the removed channel(s) to the scan list, turn the radio off and then back on, or exit and re-enter the scanning mode by pressing MON. 5. You cannot remove the home channel from the scan list. 6. In Advanced Scan, the detected code will only be used for one transmission. You must note the code, exit scan, and set that detected code on that channel to permanently use the detected code.
To transmit to a radio that has QT noise filtering turned on: 1. Select the same channel and Interference Eliminator Code as the other radio. 2. Press to send a call tone. This allows your voice to pass through the QT noise filter on the receiving radio. 3. Press PTT and speak normally. Note: If you skip step 2, the beginning of your message may not be heard on the receiving radio. For a 30-second period, starting after the last transmission, all transmissions received on the selected channel and code will pass through the QT noise filter. Keypad Tones You may enable or disable the speaker key tones. You will hear the key tone each time a button is pushed. 1. Press until appears. The current setting On/Off will flash 2. Press either + or to turn On or Off. 3. Press PTT to confirm or to continue set up.
to save the weather channel setting.
Setting the Weather Alert Your radio can be set to respond to NOAA Weather Radio emergency messages. A special alarm tone sounds an alert and turns on the weather receiver to give you immediate weather and emergency information. 1. After turning weather reception on, press
Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable. What will GIANT INTERNATIONAL LTD. do? GIANT INTERNATIONAL LTD., at its option, will at no charge repair, replace or refund the purchase price of any Products or Accessories that does not conform to this warranty. We may use functionally equivalent reconditioned/ refurbished/ pre-owned or new Products, Accessories or parts. How to Obtain Warranty Service or Other Information? To obtain service or information, please call:
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
twice. On/Off displays.
Note: When the key tone feature is off, the following are not disabled: Transmit timeout alert tone Call tone Low battery alert tone or The transmitted talk confirmation tone. Transmitting a Talk Confirmation Tone You can set your radio to transmit a unique tone when you finish transmitting. It is like saying Roger or Over to let others know you are finished talking. 1. With the radio on, press until the appears. The current setting On/Off flashes. 2. Press + or to turn On or Off. 3. Press PTT to set or to complete set up.
2. Press + or to select On/Off. If you activate Weather Alert and return to two-way mode, will display. 3. Press
to save the weather alert setting.
4. Press + to return to two-way mode. As with two-way radio reception, weather channel reception depends on how close you are to a transmitter and whether you are indoors or outdoors. Because weather channels are transmitted without codes, they may contain static or noise. Weather Alert will not function while actively transmitting or receiving in two-way mode. Channels and Frequencies Channel Frequency 11 462.5625 MHz 462.5875 MHz 462.6125 MHz 462.6375 MHz 462.6625 MHz 462.6875 MHz 462.7125 MHz 467.5625 MHz 467.5875 MHz 467.6125 MHz 467.6375 MHz Description Channel GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS GMRS/FRS FRS FRS FRS FRS 22 Frequency 467.6625 MHz 467.6875 MHz 467.7125 MHz 462.5500 MHz 462.5750 MHz 462.6000 MHz 462.6250 MHz 462.6500 MHz 462.6750 MHz 462.7000 MHz 462.7250 MHz Description FRS FRS FRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS
USA Two-Way Radios
Canada Two-Way Radios
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not For Accessories, please call the telephone number designated above for apply to you. This warranty gives you specific legal rights, and you may the product with which they are used. also have other rights that vary from state to state or from one You will receive instructions on how to ship the Products or Accessories at your expense, to a GIANT INTERNATIONAL LTD. Authorized Repair Center. jurisdiction to another. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number.
Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official licensee for this product. Motorola, the Motorola logo trademarks and the Motorola trade dress are owned by Motorola, Inc. and are used under license from Motorola, Inc. Please contact Giant International Ltd. at 800-638-5119 for questions/comments, warranty, support, or service related to this product. MOTOROLA and the Stylized M Logo are registered in the U.S. Patent & Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. 2007.
Weather Channels and Frequencies Weather Channel WX1 WX2 WX3 WX4 WX5 WX6 Frequency 162.550 MHz 162.400 MHz 162.475 MHz 162.425 MHz 162.450 MHz 162.500 MHz T8500/T8510/T8530/T8550 Weather Channel WX7 WX8 WX9 WX10 WX11 Frequency 162.525 MHz 161.650 MHz 161.775 MHz 161.750 MHz 162.000 MHz
WF2702 P5Q Se2 10K V ZBF360X MN-100-L- SCH-U820 4 0 ML-1630W XAA Monitor LP290 FCV100 3850 WX CL28W440AN XRS9700 22HFL3330D TI-30X II RH-706 AJ3010 Console Mk2 Nikon 995 KX-TG2224W YZ426F-2002 122mkiii IC-281H HT-C720 50 LC Vintage2-PH1 S-DV1000SW Fireworks GTA 4100 Adventure 2 MB-3917H WF410ANW FT-1802M Software Decade ARC 3 Ryobi 105R VSC-MP1 Servers Prokit 444 Dvdr70 001 CDX-GT350 OPH 614 Ru880 Calculator C109STF DVK-9711N EDC510E Armada M700 Series II Finedrive 400 HD160JJ-SCC EQ700 GQ600 Desktop PC C541I CL-21Z43MJ Discworld Noir Boss PH-3 C1320D ZWF-1238 5 0 CR-6530 DV-S77 Asus P5A Becker Z098 LA26A450c1D CDX-GT730UI Expresso Plus VL6-E XM-ZR604 PW80-2004 Black VSX-D938TX X1100 PCV-LX900 Force Lrfd22850 Deskjet 3900 Chorus SLV-R100 CS5123 Chauffe-EAU Aspire 5610 Chocolat KX-TGA915EX Soulcalibur III Blackberry 7730 Servers M197DN FA580 CQ-RDP142N 42LE2R QY100 Htbe1 Airmax5 USR5461 Abit KD7A Strike
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101