Optional Features

This label identifies an optional network, SIM card, or subscription-dependent feature that may not be offered by all service providers in all geographical areas. Contact your service provider for more information.

Optional Accessories

This label identifies a feature that requires an optional Motorola Original accessory.

Installing the SIM Card

Your Subscriber Identity Module (SIM) card contains your phone number, service details, and phonebook/message memory. Caution: Do not bend or scratch your SIM card. Avoid exposing your SIM card to static electricity, water, or dirt. Slide the SIM card under the retention strap to insert it into the card slot as shown below:

Battery Tips

Battery life depends on the network, signal strength, temperature, features, and accessories you use. Always use Motorola Original batteries and chargers. The warranty does not cover damage caused by using non-Motorola batteries and/or chargers. New batteries or batteries stored for a long time may take more time to charge. When charging your battery, keep it near room temperature. When storing your battery, keep it uncharged in a cool, dark, dry place, such as a refrigerator. Never expose batteries to temperatures below -10C (14F) or above 45C (113F). Always take your phone with you when you leave your vehicle. It is normal for batteries to gradually wear down and require longer charging times. If you notice a change in your battery life, it is probably time to purchase a new battery. Contact your local recycling center for proper battery disposal. Warning: Never dispose of batteries in a fire because they may explode. Before using your phone, read the battery safety information in the Safety and General Information section included in the gray-edged pages at the back of this guide. 10

Installing the Battery

Charging the Battery
New batteries are shipped partially charged. Before you can use your phone, you need to install and charge the battery as described below. Some batteries perform best after several full charge/discharge cycles.
Tip: The angle connector provided with your phone makes it easier for you to use the phone with an attached battery charger or phone accessory. Action 1 Insert the travel charger plug into the detachable angle connector as shown. 2 Insert the angle connector plug into the USB connector port on your phone. 3 Plug the other end of the travel charger into the appropriate electrical outlet. Note: It may take up to 10 seconds for your phone to provide a visible or audible indication that the battery is charging. 4 When your phone indicates Charge Complete, remove the travel charger and angle connector. Note: You can safely leave the travel charger connected to the phone after charging is complete. This will not damage the battery.

Sending a Multimedia Message
A Multimedia Messaging Service (MMS) multimedia message contains one or more pages with text and embedded media objects (including photos, pictures, animations, sounds, voice records, and video clips). You can send a multimedia message to other MMS-capable phones, and to email addresses.
Tip: The layout of all pages in a multimedia message is defined by the layout of the first page. To display a media object at the top of the page, insert it in the first half of the message text. To display a media object at the bottom of the page, insert it in the second half of the message text. Find the Feature Press 1 keypad keys 2 M E > Create Message > New Multimedia Msg To enter text on the page open the MMS Menu 19
Press 3 S 4 SELECT (+) 5 S
6 SELECT (+) 7 S 8 SELECT (+)
To scroll to Insert display a list of items you can insert scroll to Picture, Voice Record, Sound, Video, New Page, Quick Note, or Contact Info select the file type highlight the file you want insert the file To add another page to the message, continue to step 9. open the MMS Menu to insert a new page scroll to Insert display a list of items you can insert scroll to New Page insert a new page after the current page Repeat steps 1 to 8 to enter contents for the new page.
9 M 10 S 11 SELECT (+) 12 S 13 SELECT (+)
When you finish composing the multimedia message: Press 1 OK (+) 2 S To store the message scroll to a Send To option: Highlight an existing phonebook entry. Or highlight [One Time Entry] to enter one or more phone numbers or email addresses. Or highlight [New Phonebook Entry] to enter a number/address and add it to the phonebook. add the phonebook entry to the list of recipients Repeat steps 2 and 3 to add additional phonebook entries to the list. or SELECT (+) 4 DONE (+) 5 S 6 CHANGE (-) 7 keypad keys select [One Time Entry] or [New Phonebook Entry] store the numbers/addresses scroll to Subject

3 ADD (+)

select Subject enter the subject 21
Press 8 OK (+) 9 CHANGE (-) S SELECT (+) S SELECT (+) BACK (-) S
16 CHANGE (-) 17 ADD (+) or REMOVE (+) 18 DONE (-) 19 SEND (+) or M
To store the subject select Attachments to attach a file to the message, if desired scroll to Picture, Sounds, or Video select the file type highlight the file you want attach the file return to the message editor scroll to Receipt to request a receipt, if desired select Receipt activate/deactivate the delivery report return to the message editor send the message view message details, save the message in the drafts folder, or cancel the message

Highlight Features 22

Using a Bluetooth Wireless Connection
Your phone supports Bluetooth wireless connections. You can set up a wireless link with a Bluetooth headset or handsfree car kit, or connect to a computer or hand-held device to exchange and synchronize data. Note: Your phone's Bluetooth features and Bluetooth Class 1 power levels are not allowed for outdoor operation in France. To avoid unlawful interference with radio signals, do not use the Bluetooth features in France unless you are indoors. Highlight Features

Turning Bluetooth Power On or Off
The preferred method for connecting your phone to a Bluetooth headset or handsfree car kit is to turn on Bluetooth power on your phone, then connect your phone to the headset or car kit. To turn Bluetooth power on: Find the Feature M > Settings > Connection > Bluetooth Link > Setup > Power > On
This procedure turns Bluetooth power on and leaves it on until you turn it off. When your phones Bluetooth power is on, your handsfree accessory can automatically reconnect to the phone when you turn on the accessory or move it within range of the phone. Note: To extend battery life, use the above procedure and set Bluetooth power to Off when not in use. 23
Searching for Other Devices
To connect your phone to a Bluetooth headset or handsfree device: Find the Feature M > Settings > Connection > Bluetooth Link > Handsfree > [Look For Devices]

Highlight Features 24

If Bluetooth power is turned off, your phone prompts you to Temporarily Power On? the Bluetooth power setting. Press YES (-) to proceed. Alternatively, set Power to On in the Setup menu to turn Bluetooth power on and leave it on. Your phone scans for and displays a list of device(s) located within range of the phone. Note: If your phone is already connected to a device, you must disconnect from it to search for other devices. To connect to a device, highlight the device name and press SELECT (+). The device may request permission to bond with your phone. Select YES (-) and enter the correct PIN code to create a secure connection with the device. When the connection is made, the Bluetooth indicator displays in the home screen, and the external Bluetooth LED indicator flashes.
Sending Objects to Another Device
You can use a Bluetooth wireless connection to send a picture, sound, video, phonebook entry, datebook event, or bookmark from your phone to another phone, computer, or hand-held device.
Sending a Picture, Sound, or Video
Highlight the object on your phone that you want to send to the other device, then press M > Copy. Select a recognized device name listed in the Object Exchange menu, or [Look For Devices] to search for the device to which you want to send the object. Highlight Features 25
Sending a Phonebook Entry, Datebook Event, or Bookmark
Highlight the item on your phone that you want to send to the other device, then press M > Send. Select a recognized device name listed in the Object Exchange menu, or [Look For Devices] to search for the device to which you want to send the item.
Learning to Use Your Phone
See page 1 for a basic phone diagram.

Using the Display

The home screen is displayed when you are not on a call or using the menu. You must be in the home screen to dial a phone number. Learning to Use Your Phone

Date Recent Calls Phonebook
Service Provider 10/15/05

Messages Browser Clock

STYLES

CAMERA

Left Soft Key Label

Menu Indicator

Right Soft Key Label
Press the 4-way navigation key S up, down, left, or right to select a menu feature icon. If you select a menu icon by mistake, press O to return to the home screen. The menu indicator M shows that you can press the menu key M to enter the main menu. 26
Labels at the bottom corners of the display show the current soft key functions. Press the left soft key - or right soft key + to perform the indicated function. Notes: Your home screen may appear different than shown. For example, the menu feature icons normally are hidden to allow a better view of the wallpaper image. You can still select the menu icons when they are hidden from view. To show or hide menu icons, see page 81. Your phone can display an analog or digital clock in the home screen (see page 80). Your phones display normally is visible only when the display backlight is on, or when the display is viewed in direct sunlight. To extend battery life, the backlight turns off automatically when no activity is detected for a specified time. The backlight turns back on when you open the flip or press any key. To set the time that the backlight stays on, see page 60. To further extend battery life, you can set the display to turn off (in addition to the backlight) when no activity is detected for a specified time. The display turns back on when you open the flip or press any key. To set the time that the display stays on, see page 61. Learning to Use Your Phone 27
The following status indicators can display:
4. Roam 3. Signal Strength 2. GPRS 1. Data

5. Active Line

6. Messaging Presence
7. Message 8. Battery Level 9. Ring Style
1. Data Indicator Shows connection and data transmission status. The Bluetooth wireless connection indicator shows when a Bluetooth connection is active. Other indicators can include: 4 = secure packet data transfer 3 = secure application connection 2 = secure Circuit Switch Data (CSD) call 7 = unsecure packet data transfer 6 = unsecure application connection 5 = unsecure CSD call

Msg Prog ram

Press S up to accept Program. Press S right to highlight another combination.
Prog Proh Spoi Proi DELETE SELECT
Press SELECT (+) to select highlighted combination with no space.
If you want a different word (such as Progress), continue pressing keypad keys to enter the remaining characters.
Entering Novel Words in iTAP Mode
You may enter a word that the iTAP software does not recognize. If your word is not shown as a letter combination choice at the bottom of the display: Action 1 Press DELETE (-) one or more times to delete letters, until you see a letter combination at the bottom of the display that matches the start of the word you want to enter. 2 Press S left or right to highlight the letter combination.
Action 3 Press SELECT (-) to select the letter combination. 4 Continue to enter letters and select letter combinations to spell the word. Your phone automatically stores the novel word and displays it as an option the next time you enter its letter combination. When the memory space for storing novel words is filled, your phone deletes the oldest words to add new words.
Entering Numbers and Punctuation in iTAP Mode
Learning to Use Your Phone 40 To enter numbers quickly, press and hold a number key to temporarily switch to numeric mode. Press the number keys to enter the numbers you want. Enter a space to revert to iTAP mode. Press 1 to enter punctuation or other characters as shown in the Character Chart on page 43.

Using Tap Mode

This is the basic text entry mode on your phone. Tap mode cycles through the letters and number of the key you press. Tap Extended mode also cycles through additional symbols as shown in the Character Chart on page 43. If necessary, press # in a text entry screen to switch to Tap mode. An indicator shows which mode is active (see page 37). If Tap or Tap Extended is not set as the Primary or Secondary entry mode, see page 36.
Tap Mode Text Entry Rules
Press a keypad key repeatedly to cycle through its characters. For example, you would press 2 one time to enter a, two times to enter b, three times to enter c, or four times to enter 2. After 2 seconds, Tap mode accepts the character, and the cursor moves to the next position. The first character of every sentence is capitalized. If necessary, press S down to change the character to lowercase before the cursor moves to the next position. Press S to move the flashing cursor to enter or edit message text. If you do not want to save your text or text edits, press O to exit without saving. Learning to Use Your Phone

Option Send Tones

Description Send the number to the network as DTMF tones. Note: This option displays only during a call. Talk and then send a fax in the same call (see page 87).

Talk then Fax

Redialing a Number
Calling Features Press 1 N 2 S 3 N To view the dialed calls list scroll to the entry you want to call redial the number

Using Automatic Redial

When you receive a busy signal, your phone displays Call Failed, Number Busy. To redial the number

Press N or RETRY (+)

When the call goes through, your phone rings or vibrates one time, displays Redial Successful, and connects the call.
Your phone keeps a record of your unanswered calls, and displays: the missed call indicator X Missed Calls, where X is the number of missed calls Press 1 VIEW (+) 2 S 3 N To display the received calls list select a call to return make the call Calling Features

Using the Notepad

The most recent set of digits entered on the keypad are stored in your phones notepad memory. This can be a phone number that you called, or a number that you jot down during a call, for later use. To retrieve the number stored in the notepad: Find the Feature M > Recent Calls > Notepad
Press N or STORE (+) or M
To call the number create a phonebook entry with the number in the No. field open the Dialing Menu to attach a number or insert a special character
Putting a Call On Hold or Mute
Press M > Hold or M > Mute mute all active calls To put all active calls on hold

Using Call Waiting

When you are on a call, an alert tone sounds to indicate that you have received a second call.
Press 1 N 2 SWITCH (+) or LINK (-) or M > End Call On Hold
To answer the new call switch between calls connect the 2 calls end the call on hold
If necessary, you must turn on call waiting to use the feature. To turn call waiting on or off: Find the Feature M > Settings > In-Call Setup > Call Waiting
Using Caller ID (Incoming Calls)
Calling line identification (caller ID) displays the phone number for incoming calls in your phones external and internal displays.

The phone displays the callers name (and picture ID, if available) when the name is stored in your phonebook, or Incoming Call when caller ID information is not available. You can also set your phone to play a distinctive ringer ID for specific entries stored in your phonebook. For more information, see page 76.
Calling an Emergency Number
Your service provider programs one or more emergency phone numbers, such as 911 or 112, that you can call under any circumstances, even when your phone is locked or the SIM card is not inserted. Note: Emergency numbers vary by country. Your phones preprogrammed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues. Calling Features Press 1 keypad keys 2 N To dial the emergency number call the emergency number
Dialing International Numbers
If your phone service includes international dialing, press and hold 0 to insert the local international access code (+) for the country from which you are calling. (Inserting + enables your phone to make an international call.) Then press the keypad keys as usual to dial the country code and phone number.
Calling With 1-Touch Dial
To call phonebook entries 1 through 9, press and hold the single-digit speed dial number for one second.
You can set 1-touch dial to call the entries in your phone memory phonebook or the SIM card phonebook: Find the Feature Press 1 S 2 SELECT (+) M > Settings > Initial Setup > 1-Touch Dial To scroll to the location you want select the location

Using Voicemail

Voicemail messages that you receive are stored on the network. To listen to your messages, you must call your voicemail phone number.
Note: Your service provider may include additional information about using this feature.
Listening to Voicemail Messages
Find the Feature E > Voicemail The phone calls your voicemail phone number. If no voicemail number is stored, your phone prompts you to store a number.
Receiving a Voicemail Message
When you receive a voicemail message, your phone displays the voicemail message indicator t and the New Voicemail notification. Press CALL (+) To listen to the message
The phone calls your voicemail phone number. If no voicemail number is stored, your phone prompts you to store a number. Calling Features
Storing Your Voicemail Number
If necessary, use the following procedure to store your voicemail phone number on your phone. Usually, your service provider has already done this for you. Find the Feature Press 1 keypad keys 2 OK (+) E M > Voicemail Setup To enter your voicemail number store the number
Note: You cannot store a p (pause), w (wait), or n (number) character in this number. If you want to store a voicemail number with these characters, create a phonebook entry for it. Then, you can use the entry to call your voicemail. For more information about these characters, see the More Here guide.

Feature Description Dial Number Call a number stored in the phonebook: M > Phonebook, highlight the phonebook entry, press N to call Voice Dial Voice dial a number stored in the Number phonebook: Press and release the voice key, and say the entrys name (within 2 seconds). Set Ringer Assign a distinctive ringer alert to an ID for Entry entry: M > Phonebook > entry M > Edit > Ringer ID > ringer name Note: The Ringer ID option is not available for entries stored on the SIM card. Phone Features Set Picture ID for Entry To activate ringer IDs, see page 80. Assign a photo or picture to display when you receive a call from an entry: M > Phonebook > entry M > Edit > Picture > picture name Note: The Picture option is not available for entries stored on the SIM card.
Feature Set Picture ID View
Description View phonebook entries as a text list, or with picture caller ID photos: M > Phonebook M > Setup > View by > view name Set Set the category for an entry: Category for M > Phonebook > entry Entry M > Edit > Category > category name Note: The Category option is not available for entries stored on the SIM card. Set a category view: M > Phonebook M > Categories > category view Set a distinctive ring alert (ringer ID) to sound when you receive calls from entries in a specific category: M > Phonebook M > Categories, highlight the category, press M > Edit > Ringer ID. Note: The Ringer ID option is not available for entries stored on the SIM card. To activate ringer IDs, see page 80.
Set Category View Set Category Ringer ID
Feature Sort Phonebook List Set Primary Number or Address
Copy Phonebook Entry Send Phonebook Entry to Another Device Create Group Mailing List
Description Set the order in which entries are listed: M > Phonebook M > Setup > Sort by > sort order Set the primary number for an entry with multiple numbers: M > Phonebook, highlight the entry, press M > Set Primary > number or address. Copy an entry between the phone and SIM card: M > Phonebook, highlight the entry, press M > Copy > Entries > To Send a phonebook entry to another phone, computer, or device: M > Phonebook, highlight the entry, press M > Send Create a group mailing list as a phonebook entry: M > Phonebook M > New > Mailing List

032380o 032380o

Feature Download Objects from Web Page

Web Sessions

Download Game or Application
Start Game or Application

Play Music

Create Playlist
Description Download a picture, sound, or phone theme from a Web page: Highlight the file, press SELECT (+), press STORE (+). Select or create a Web session: M > Web Access > Web Sessions Download a Java game or application with the micro-browser: M > Web Access > Browser, highlight the application, press SELECT (+), press DWNLOAD (+) Start a Java game or application: M > Games & Apps, highlight the application, press SELECT (+) Play a song on your phone: M > Multimedia > Sounds > song name Create a playlist of songs to play on your phone: M > Multimedia > Sounds > [New Playlist]
032380o 032380o 032380o 032380o
Feature Create Ring Tones
Description Create iMelody ring tones that you can use with your phone: M > Multimedia > Sounds > [New iMelody]

Phone Features 94

Troubleshooting
If you have questions or need help, were here to help. Go to www.motorola.com/consumer/support, where you can select from a number of customer care options. You can also contact the Motorola Customer Support Center at 1-800-331-6456 (United States), 1-888-390-6456 (TTY/TDD United States for hearing impaired), or 1-800-461-4575 (Canada).
Specific Absorption Rate Data
The model wireless phone meets the governments requirements for exposure to radio waves. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age or health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 W/kg.1 Tests for SAR are conducted using standard operating positions accepted by the FCC and by Industry Canada with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the power output. Before a phone model is available for sale to the public in the U.S. and Canada, it must be tested and certified to the FCC and Industry Canada that it does not exceed the limit established by each government for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) reported to the FCC and available for review by Industry Canada. The highest SAR value for this model phone when 96

tested for use at the ear is 0.89 W/kg, and when worn on the body, as described in this user guide, is 0.58 W/kg. The SAR value for this product in its data transmission mode (body-worn use) is 1.24 W/kg. (Body-worn measurements differ among phone models, depending upon available accessories and regulatory requirements).2 While there may be differences between the SAR levels of various phones and at various positions, they all meet the governmental requirements for safe exposure. Please note that improvements to this product model could cause differences in the SAR value for later products; in all cases, products are designed to be within the guidelines. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site: http://www.phonefacts.net or the Canadian Wireless Telecommunications Association (CWTA) Web site: http://www.cwta.ca
1. In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. 2. The SAR information includes the Motorola testing protocol, assessment procedure, and measurement uncertainty range for this product.
European Union Directives Conformance Statement

[France Only]

Hereby, Motorola declares that this product is in compliance with: The essential requirements and other relevant provisions of Directive 1999/5/EC All other relevant EU Directives

Product Approval Number

The above gives an example of a typical Product Approval Number. You can view your products Declaration of Conformity (DoC) to Directive 1999/5/EC (the R&TTE Directive) at www.motorola.com/rtte - to find your DoC, enter the product Approval Number from your products label in the Search bar on the Web site.
accessories 9, 47, 75, 86, 87, 88 accessory connector port 1 active line indicator 29 active line, changing 71 alarm clock 90 alert creating 94 defined 54 reminder 80 setting 14, 46, 54, 55 turning off 14, 62 animation 19, 56, 57, 92 answering a call 15, 59 attach number 63, 74 Bluetooth wireless connection 3, 23, 79, 88, 90 brightness 60 browser. See micro-browser
calculator 91 call alert, turning off 14, 62 answering 15, 59 barring 75 costs 86 dialing 14, 52, 77 emergency number 68 ending 14, 15 forwarding 75 hold 66 international dialing 68 making 14, 52, 77 mute 66 receiving 15 returning 47, 65 talk then fax 64 timers 86 transferring 74 call barring password 48 99

Part Number: 6809476A21-O 2
Safety and General Information. 4 FDA Consumer Information on Wireless Phones. 10 Product Registration. 20 RF Energy Interference. 20 Export Law Assurances. 20 Wireless: The New Recyclable. 21 Wireless Phone Safety Tips. 23
Safety and General Information
IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR PHONE. The information provided in this document supersedes the general safety information in users guides published prior to December 1, 2002.
Exposure To Radio Frequency (RF) Energy
Your phone contains a transmitter and a receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits. Your Motorola phone is designed to comply with local regulatory requirements in your country concerning exposure of human beings to RF energy.

Operational Precautions

To assure optimal phone performance and make sure human exposure to RF energy is within the guidelines set forth in the relevant standards, always adhere to the following procedures.

External Antenna Care

Use only the supplied or Motorola-approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone. Do NOT hold the external antenna when the phone is IN USE. Holding the external antenna affects call quality and may cause the phone to operate at a higher power level than needed. In addition, use of unauthorized antennas may result in non-compliance with the local regulatory requirements in your country.

Phone Operation

When placing or receiving a phone call, hold your phone as you would a wireline telephone.

Body-Worn Operation

To maintain compliance with RF energy exposure guidelines, if you wear a phone on your body when transmitting, always place the phone in a Motorola-supplied or approved clip, holder, holster, case, or body harness for this phone, if available. Use of accessories not approved by Motorola may exceed RF energy exposure guidelines. If you do not use one of the body-worn accessories approved or supplied by Motorola, and are not using the phone held in the normal use position, ensure the phone and its antenna are at least 1 inch (2.5 centimeters) from your body when transmitting.

Data Operation

When using any data feature of the phone, with or without an accessory cable, position the phone and its antenna at least 1 inch (2.5 centimeters) from your body.

Approved Accessories

Use of accessories not approved by Motorola, including but not limited to batteries and antennas, may cause your phone to exceed RF energy exposure guidelines. For a list of approved Motorola accessories, visit our website at www.Motorola.com.
RF Energy Interference/Compatibility
Note: Nearly every electronic device is susceptible to RF energy interference from external sources if inadequately shielded, designed, or otherwise configured for RF energy compatibility. In some circumstances your phone may cause interference.

Facilities

Turn off your phone in any facility where posted notices instruct you to do so. These facilities may include hospitals or health care facilities that may be using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your phone when on board an aircraft. Any use of a phone must be in accordance with applicable regulations per airline crew instructions.

Medical Devices

Pacemakers Pacemaker manufacturers recommend that a minimum separation of 6 inches (15 centimeters) be maintained between a handheld wireless phone and a pacemaker. Persons with pacemakers should: ALWAYS keep the phone more than 6 inches (15 centimeters) from your pacemaker when the phone is turned ON. NOT carry the phone in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn OFF the phone immediately if you have any reason to suspect that interference is taking place. Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. 6

Use While Driving

Check the laws and regulations on the use of phones in the area where you drive. Always obey them. When using your phone while driving, please: Give full attention to driving and to the road. Use handsfree operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. Responsible driving best practices may be found in the Wireless Phone Safety Tips at the end of this manual and at the Motorola website: www.Motorola.com/callsmart.

FCC also regulates the base stations that the wireless phone networks rely upon. While these base stations operate at higher power than do the wireless phones themselves, the RF exposures that people get from these base stations are typically thousands of times lower than those they can get from wireless phones. Base stations are thus not the primary subject of the safety questions discussed in this document.
What is FDA doing to find out more about the possible health effects of wireless phone RF?
FDA is working with the U.S. National Toxicology Program and with groups of investigators around the world to ensure that high priority animal studies are conducted to address important questions about the effects of exposure to radio frequency energy (RF). FDA has been a leading participant in the World Health Organization International Electromagnetic Fields (EMF) Project since its inception in 1996. An influential result of this work has been the development of a detailed agenda of research needs that has driven the establishment of new research programs around the world. The Project has also helped develop a series of public information documents on EMF issues. FDA and the Cellular Telecommunications & Internet Association (CTIA) have a formal Cooperative Research and Development Agreement (CRADA) to do research on wireless phone safety. FDA provides the scientific oversight, obtaining input from experts in government, industry, and academic organizations. CTIA-funded research is conducted through contracts to independent investigators. The initial research will include both laboratory studies and studies of wireless phone users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world.
What steps can I take to reduce my exposure to radio frequency energy from my wireless phone?
If there is a risk from these products--and at this point we do not know that there is--it is probably very small. But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radio frequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure. If you must conduct extended conversations by wireless phone every day, you could place more distance between your body and the source of the RF, since the exposure level drops off dramatically with distance. For example, you could use a headset and carry the wireless phone away from your body or use a wireless phone connected to a remote antenna Again, the scientific data do not demonstrate that wireless phones are harmful. But if you are concerned about the RF exposure from these products, you can use measures like those described above to reduce your RF exposure from wireless phone use.
What about children using wireless phones?

* optional features

Use and Care
To care for your Motorola phone, please keep it away from:
liquids of any kind Dont expose your phone to water, rain, extreme humidity, sweat, or other moisture. If it does get wet, dont try to accelerate drying with the use of an oven or dryer, as this may damage the phone. extreme heat or cold Avoid temperatures below 0C/32F or above 45C/113F.
dust and dirt Dont expose your phone to dust, dirt, sand, food, or other inappropriate materials.
cleaning solutions To clean your phone, use only a dry soft cloth. Dont use alcohol or other cleaning solutions.
microwaves Dont try to dry your phone in a microwave oven.
the ground Dont drop your phone.

essentials

about this guide
This guide shows how to locate a menu feature as follows: symbols This means a feature is network/subscription dependent and may not be available in all areas. Contact your service provider for more information. This means a feature requires an optional accessory.
Find it: a > s Recent Calls > Dialed Calls
This means that, from the home screen: Press the menu key a to open the menu. Press the navigation key S to scroll to
s Recent Calls, and press the center key s to
select it. 3 Press the navigation key S to scroll to Dialed Calls, and press the center key s to select it.

SIM card

Caution: Dont bend or scratch your SIM card. Keep it away from static electricity, water, and dirt. Your Subscriber Identity Module (SIM) card contains personal information like your phone number and phonebook entries. 1 If necessary, press in the battery door release latch and remove the battery door.
Hold the SIM card with the notch in the lower left corner and the gold plate facing down. Slide the SIM card under the metal clip and into the card slot.

battery

battery use & safety
Motorola recommends you always use Motorola-branded batteries and chargers. The warranty does not cover damage caused by non-Motorola batteries and/or chargers. Caution: Use of an unqualified battery or
charger may present a risk of fire, explosion, leakage, or other hazard. Improper battery use, or use of a damaged battery, may result in a fire, explosion, or other hazard. Battery usage by children should be supervised. Important: Motorola mobile devices are designed to work best with qualified batteries. If you see a message on your display such as Invalid Battery or Unable to Charge, take the following steps: Remove the battery and inspect it to confirm that it bears a Motorola Original Equipment hologram; If there is no hologram, the battery is not a qualified battery; If there is a hologram, replace the battery and retry charging it;

search the phonebook

To search for a phonebook contact:
Press the keypad keys to enter the first letters of the contact you want. The phonebook list jumps to the contact name that begins with the letters you type.

main attractions

You can do much more with your phone than make and receive calls!

photos

take a photo
Press a > h Multimedia > Camera to see the camera viewfinder.
Press S up/down to zoom in/out. Press S left/right to decrease/ increase exposure. Photo Viewfinder 022 Remaining Back Return to previous screen. Capture
Photos remaining Take a photo. Press a to open Pictures Menu.
Point the camera lens at the photo subject. Press Capture to take a photo.
Press Store to select a storage option: Send in Message, Store Only, Apply as My Icon, Apply as Wallpaper, Apply as Screen Saver, Apply as Phonebook Entry, or Print and Store. or Press Discard to delete the photo and return to the active viewfinder.

camera settings

When the camera viewfinder is active, press a to select camera options: options Go To Pictures See stored pictures and photos. Press
If you choose to send the photo in a message, see send a multimedia message on page 23. Note: You cant assign a photo to a phonebook entry stored on the SIM card. Auto-Timed Capture Pictures Setup
a to perform various operations
(such as Delete, Rename, or Move) on a picture. Set a timer for the camera to take a photo. Adjust photo settings: Lighting Conditions Resolution Shutter Tone View Free Space See how much memory remains for storing pictures.

self portrait

When the camera viewfinder is active, you can close the phone flip to show the viewfinder image in the external display. Press the smart key (see illustration on page 2) to take a photo. Open the flip to store or discard the photo.

videos

record a video
Press a > h Multimedia > Video Camera to see the video camera viewfinder.
Press Capture to begin video recording. Press Stop to stop video recording. Press Store to select a storage option: Send in Message or Store Only. or Press Discard to delete the video and return to the
Press S up/down to zoom in/out. Video Viewfinder 010 Remaining Back Return to previous screen. Capture
Videos remaining Start video capture. Press a to open Videos Menu.
active viewfinder. If you choose to send the video in a message, see send a multimedia message on page 23. When the video camera viewfinder is active, press a to select video options: options Go To Videos See stored videos. Press a to perform various operations (such as Delete, Rename, or Move) on a video.
Note: You can zoom only before you start recording. 1 Point the camera lens at the video subject.
options Videos Setup Adjust video settings: Auto Repeat Video Length Lighting Conditions Resolution Recording Sound Recording Sound Turn on/off video sound recording.

play a video

Find it: a > h Multimedia > Videos > video
Timer bar shows % played. See video information. Press a to open Videos Menu.
Press S up/down to pause/play. Press S left/right to skip to previous/ next video. Video Name 00:09/00:15 Back Return to previous screen. Details
From the stored videos list, press a to select video options: options Send in Message Insert a video in a new message.
options New Activate the video camera to record a new video. Details Rename Delete Move See video information. Rename a video. Delete marked video(s). Move video(s) to another device, delete original(s) from phone memory. Copy Copy video(s) to another device, leave original(s) on phone. Mark Mark one or more videos that you want to delete, move, copy, or assign to a category. Mark All Mark all videos, so you can delete, move, copy, or assign them to a category.
options Categories Create new category, or see videos in a selected category. Assign To Category Videos Setup View Free Space Adjust video recording settings. See how much memory remains for storing videos. Assign video(s) to a category.

multimedia messages

For more messaging features, see page 57. 2
a > Insert > New Page. You can enter more text and
objects on the new page. When you finish the message, press a > Message Options to set message options (such as Subject and Priority). 3 When you finish setting message options, press Done. 4 To select message recipients, press Send To. You can: Select one or more entries from your phonebook (press S to scroll to an entry, and press the center key s to select it). Select [New Number] or [New Email Address] to enter a phone number or email address. 5 To send the message, press Send. To cancel or save the message as a Draft, press
send a multimedia message
A Multimedia Messaging Service (MMS) message contains pages with text and media objects (including photos, sounds, or videos). You can send the multimedia message to other MMS-capable phones, and to email addresses.
Find it: R > Create Message > New Multimedia Msg
1 Press keypad keys to enter text on the page (for more information about text entry, see page 33). To insert a picture, sound, video, voice record, quick note, or contact info on the page, press
a > Insert. Select the file type and the file.
To insert another page in the message, enter text or objects on the current page and press
receive a multimedia message
When you receive a multimedia message, your phone plays an alert and the display shows New Message with a message indicator (such as r). Press Read to open the message. Pictures and animations show as you read the message. Sound files play as you read the message. Use the volume keys to adjust the sound volume. Attached files are added to the end of the message. To open an attachment, scroll to the file indicator/file name and press View (image), Play (sound), or Open (phonebook vCard, datebook vCalendar entry, or unknown file type).

phone calls

I = available for IM Q = invisible to IM X = offline
y = loud ring | = vibrate } = vibrate then
z = soft ring = vibrate and ring { = silent
The Java indicator shows when a Java application is active. 9 Battery Level Indicator Vertical bars show the battery charge level. Recharge the battery when your phone shows Low Battery.

text entry

Some features let you enter text.
Press # in a text entry screen to select an entry mode: entry modes
For indicator descriptions, see following section. Flashing cursor indicates insertion point.

j or g

Character Counter Press a to open sub-menu.
Your Primary text entry mode can be set to any iTAP j or tap g mode.

p or m

Your Secondary text entry mode can be set to any iTAP p or tap m mode, or set to None if you dont want a secondary entry mode.
Numeric mode enters numbers only. Symbol mode enters symbols only.
Exit without making changes.

Cancel

Send To
To set your primary and secondary text entry modes, press a > Entry Setup in a text entry screen and select Primary Setup or Secondary Setup. Tip: WANT TO SHOUT YOUR MESSAGE? Press 0 in a text entry screen to change text case to no capital
letters (U), next letter capital (V with k, n, h, or q), or all capitals (T with i, o, f, or l).
For example, if you press 6 4, your display shows:

iTAP mode

Press # in a text entry screen to switch to iTAP mode. If you dont see j or p, press a > Entry Setup to set iTAP mode as your primary or secondary text entry mode. iTAP mode lets you enter words using one keypress per letter. The iTAP software combines your keypresses into common words, and predicts each word as you enter it.
Press S up to accept Program.
443 Press S right to highlight another combination.
Prog ram Press * to enter Prog & a space. Prog Proh Spoi Proi Delete Select

Delete last letter.

Select highlighted combination with no space.
If you want a different word (such as Progress), continue pressing keypad keys to enter the remaining characters.
To enter numbers quickly, press and hold a number key to temporarily switch to numeric
mode. Press the number keys to enter the numbers you want. Enter a space to change back to iTAP mode. Press 1 to enter punctuation or other characters.
For example, if you press 7 one time, your display shows:
After two seconds, character is accepted & cursor moves to next position. Character displays at insertion point.

tap mode

Press # in a text entry screen to switch to tap mode. If you dont see g or m, press a > Entry Setup to set tap mode as your primary or secondary text entry mode. To enter text in tap mode, press a keypad key repeatedly to cycle through the letters and number on the key. Repeat this step to enter each letter.

Delete character to left of insertion point.

Delete

Press to enter message recipients.
When you enter three or more characters in a row, your phone may guess the rest of the word. For example, if you enter Prog your display might show:
If you dont want to save your text or text edits, press O to exit without saving.
Tap extended mode cycles through additional special characters and symbols as you repeatedly press a keypad key.
Press S right to accept Program. Press * to reject it & enter a space after Prog.

Prog ram

To enter a different word (such as Progress), press keys to enter ramaining characters.

numeric mode

Press # in a text entry screen until you see W. Press the number keys to enter the numbers you want.

symbol mode

The first character of every sentence is capitalized. If necessary, press S down to change the character to lowercase before the cursor moves to the next position. Press S to move the flashing cursor to enter or edit message text. Press # in a text entry screen until you see [. Press a keypad key to show its symbols at the bottom of the display. Scroll to the symbol you want, then press the center key s.

volume

Press the volume keys to: turn off an incoming call alert change the earpiece volume during a call change the ringer volume from the home screen Tip: Sometimes silence really is golden. Thats why you can quickly set your ringer to Vibrate or Silent by repeatedly pressing the down volume key in the home screen. To set the ringer from the menu, see page 40.

navigation key

Press the navigation key S up, down, left, or right to scroll and highlight menu items. When you highlight something, press the center key s to select it.

smart key

The smart key gives you another way to do things. For example, when you scroll to a menu item, you can press the smart key to select it (instead of pressing the center key s). To change what the smart key does in the home screen, see page 61.

handsfree speaker

You can use your phones handsfree speaker to make calls without holding the phone to your ear. During a call, press Speaker to turn the handsfree speaker on or off. Your display shows Spkrphone On until you turn it off or end the call. Note: The use of wireless phones while driving may cause distraction. Discontinue a call if you cant concentrate on driving. Additionally, the use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. Closing the phone flip doesnt end a call when the handsfree speaker is turned on.

codes & passwords

Your phones four-digit unlock code is originally set to 1234. The six-digit security code is originally set to 000000. If your phone is still using the original codes, you should change them:
Find it: a > w Settings > Security > New Passwords
You can also change your SIM PIN or call barring passwords.
If you forget your unlock code: At the Enter Unlock Code prompt, try entering 1234 or the last four digits of your phone number. If that doesnt work, press a and enter your six-digit security code instead. If you forget other codes: If you forget your security code, SIM PIN code, PIN2 code, or call barring password, contact your service provider.
Find it: a > w Settings > Security > Phone Lock
> Automatic Lock > On Note: You can make emergency calls on a locked phone (for more information, see page 47). A locked phone still rings or vibrates for incoming calls or messages, but you need to unlock it to answer.

lock & unlock phone

You can lock your phone to keep others from using it. To lock or unlock your phone, you need the four-digit unlock code. To manually lock your phone:
Find it: a > w Settings > Security > Phone Lock > Lock Now
To automatically lock your phone whenever you turn it off:

customize

ring style
Each ring style profile uses a different set of ringtones or vibrations for incoming calls and other events. The Silent profile silences your phone until you set another ring style. The profile indicator shows at the top of the home screen: Tip: Press and hold # in the home screen to quickly set your ringer to Silent. Press # again to switch back to the original ring style setting.
change alerts in a ring style
You can change the alerts for incoming calls and other events. Your changes are saved in the current ring style profile. Note: You cant set a ringtone for the Silent ring style profile.
y Loud | Vibrate } Vibe then Ring

To choose your profile:

z Soft Vibe & Ring { Silent
Find it: a > w Settings > Ring Styles > style name Detail
1 Scroll to Calls (or Line 1 or Line 2 for dual line phones), then press Change to change it. 2 Scroll to the alert you want, then press the center key s.

Find it: a > w Settings > Initial Setup > 1 Touch Dial

international calls

If your phone service includes international dialing, press and hold 0 to insert your local international access code (indicated by +). Then, press the keypad keys to dial the country code and phone number.
> Phone, SIM, or Fixed Dial To add a new number to the phonebook, see page 16. To edit the speed dial number for a phonebook contact, press a > n Phonebook > contact, then press a > Edit > Speed No.

voicemail

Your network stores the voicemail messages you receive. To listen to your messages, call your voicemail number. Note: Your service provider may include additional information about using this feature. When you receive a voicemail message, your phone shows the voicemail message indicator t and New Voicemail. To check voicemail messages:
phonebook entry for it. Then, you can use the entry to call your voicemail.
Find it: R > Voicemail
Your phone may prompt you to store your voicemail phone number. If you dont know your voicemail number, contact your service provider. Note: You cant store a p (pause), w (wait), or n (number) character in this number. If you want to store a voicemail number with these characters, create a

other features

advanced calling
features conference call During a call: Dial next number, press N, press Link. transfer a call During a call: Press a > Transfer, dial transfer number, press N. attach a phone number Dial an area code or prefix for a phonebook number, then: features speed dial Enter the speed dial number for a phonebook entry, press #, press N. To add a phonebook entry, see page 16. To 1-touch dial phonebook entries with single-digit speed dial numbers, see page 48. Tip: If you forget Aunt Mildreds speed dial number, press a > n Phonebook, scroll to her entry, and press View. call forwarding Set up or cancel call forwarding:

a > Attach Number

a > w Settings > Call Forward
other featuresadvanced calling
features call barring Restrict outgoing or incoming calls:
features fixed dial When you turn on fixed dialing, you can call only numbers stored in the fixed dial list. Note: You must enter your SIM PIN2 code to turn fixed dialing on or off. If you forget your PIN2 code, contact your service provider. Turn fixed dialing on or off:

a > w Settings > Security > Call Barring
TTY calls Set up your phone for use with an optional TTY device:
a > w Settings > Initial Setup > TTY Setup
change phone line If you have a dual-line-enabled SIM card, you can change your line to make and receive calls from your other phone number.
a > w Settings > Security > Fixed Dial

Use the fixed dial list:

a > ? Tools > Dialing Services > Fixed Dial
service dial Dial service phone numbers:
a > w Settings > Phone Status > Active Line
The active line indicator shows the active phone line (see illustration on page 31).
a > ? Tools > Dialing Services > Service Dial
features quick dial Dial phone numbers stored by your service provider:

phonebook

For basic phonebook features, see pages 16-17. features set phonebook view Show contacts stored in phone memory, SIM card memory, or both:
a > ? Tools > Dialing Services > Quick Dial
Edit the quick dial list:
a > w Settings > Personalize > Quick Dial
DTMF tones Activate DTMF tones:
a > n Phonebook, press a > Setup > View Contacts
> Phone & SIM, Phone Contacts Only, or SIM Contacts Only Note: The phonebook view determines where new contacts are stored. For example, when you set the view to SIM Contacts Only, any new contacts you create are stored on the SIM card.
a > w Settings > Initial Setup > DTMF
Send DTMF tones during a call: Press number keys. Send stored numbers as DTMF tones during a call: Scroll to a number in the phonebook or recent calls lists, then press a > Send Tones.

other featuresphonebook

features add new contact
features set ringer ID for contact Assign a distinctive ringtone (ringer ID) to a contact:
a > n Phonebook, press a > New Phone Contact or
New SIM Contact Contacts stored in phone memory can contain multiple phone numbers, email addresses, personal information and settings. Contacts stored on the SIM card can contain only a name and number. To set the contact storage location, see the previous feature description for set phonebook view. send message to contact
a > n Phonebook > contact, press a
> Edit > Ringer ID > ringer name Note: The Ringer ID option isnt available for contacts stored on the SIM card. To activate ringer IDs:
a > w Settings > Ring Styles > style Detail > Ringer IDs

other featuresdata & fax calls

network

features network settings See network information and adjust network settings:

personal organizer

features set alarm
a > ? Tools > Alarm Clock > [New Alarm]
turn off alarm When the display shows an alarm: To turn off the alarm, press Disable or O. To set an eight minute delay, press Snooze. add new datebook event
a > w Settings > Network
software update Your service provider can send updated phone software over the air to your phone. When your phone receives a software update, you can choose to install it immediately, or defer installation until later. To install a deferred software update:
a > ? Tools > Datebook, scroll to the day, press the
center key s, press a > New. see datebook event See or edit event details:
a > w Settings > Phone Status > Software Update

> Install Now

center key s, scroll to the event, press View.

other featuresnetwork

features datebook event reminder When the display shows an event reminder: To see reminder details, press View. To close the reminder, press Exit. send datebook event to another device Send a datebook event to another phone or computer that supports Bluetooth connections:
features create voice record Press and hold the voice key, speak into the phone, release voice key. Note: Recording of phone calls is subject to varying State and Federal laws regarding privacy and recording of phone conversations. Always obey the laws and regulations on the use of this feature. play voice record Play back a voice record:
center key s, scroll to the event, press a > Send For more information about Bluetooth connections, see page 24.
a > ? Tools > Voice Records > voice record

calculator

a > ? Tools > Calculator
other featurespersonal organizer
features currency converter

features lock feature

a > ? Tools > Calculator, press a > Exchange Rate
Enter exchange rate, press OK, enter amount, and select $ at the bottom of the display.
a > w Settings > Security > Lock Application
manage certificates Enable or disable Internet access certificates stored on your phone:

security

features SIM PIN Caution: If you enter an incorrect PIN code three times before the correct code, your SIM card is disabled and your display shows SIM Blocked. Lock or unlock the SIM card:

a > w Settings > Security > Certificate Mgmt
Certificates are used to verify the identity and security of Web sites when you download files or share information.
a > w Settings > Security > SIM PIN

other featuressecurity

fun & games

features manage pictures

features manage sounds Manage ringtones and music that you have downloaded:
a > h Multimedia > Pictures
Press a to perform various operations (such as Delete, Rename, or Move) on a photo, picture, or animation. manage videos
a > h Multimedia > Sounds
Press a to perform various operations (such as Delete, Rename, or Move) on a sound file. create ringtones Create ringtones that you can use with your phone:
a > h Multimedia > Videos
Press a to perform various operations (such as Delete, Rename, or Move) on a video.
a > h Multimedia > Sounds > [New iMelody]

play music

a > h Multimedia > Sounds > song name
other featuresfun & games
features create playlist Create a playlist of songs to play:
features download game or application You can download a Java game or application the same way you download pictures or other objects: Go to the page that links to the file, scroll to the link, and select it. start game or application Start a Java game or application: Press a > Q Games & Apps, scroll to the game or application, press the center key s to select it.
a > h Multimedia > Sounds > [New Playlist]
launch the micro-browser Press L. download objects from Web page Download a picture, sound, or phone theme from a Web page: Go to the page that links to the file, scroll to the link, and select it. Web sessions Select or create a Web session:
a > Web Access > Web Sessions

service & repairs

If you have questions or need assistance, we're here to help. Go to www.motorola.com/consumer/support where you can select from a number of customer care options. You can also contact the Motorola Customer Support Center at 1-800-331-6456 (United States), 1-888-390-6456 (TTY/TDD United States for hearing impaired), or 1-800-461-4575 (Canada).

Specific Absorption Rate Data

SAR Data

This model wireless phone meets the governments requirements for exposure to radio waves.
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age or health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 W/kg.1 Tests for SAR are conducted using standard operating positions accepted by the FCC and by Industry Canada with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR
level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the power output. Before a phone model is available for sale to the public in the U.S. and Canada, it must be tested and certified to the FCC and Industry Canada that it does not exceed the limit established by each government for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) reported to the FCC and available for review by Industry Canada. The highest SAR value for this model phone when tested for use at the ear is 0.54 W/kg, and when worn on the body, as described in this user guide, is 0.34 W/kg. The SAR value for this product in its data transmission mode (body-worn use) is 0.18 W/kg. (Body-worn measurements differ among phone models, depending upon available accessories and regulatory requirements).2 While there may be differences between the SAR levels of various phones and at various positions, they all meet the governmental requirements for safe exposure. Please note that improvements to this product model could cause differences in the SAR value for later products; in all cases, products are designed to be within the guidelines.

Operational Precautions

For optimal mobile device performance and to be sure that human exposure to RF energy does not exceed the guidelines set forth in
* The information provided in this document supersedes the general safety information in users guides published prior to May 1, 2007.
device and its antenna at least 2.5 centimeters (1 inch) from your body when transmitting. When using any data feature of the mobile device, with or without an accessory cable, position the mobile device and its antenna at least 2.5 centimeters (1 inch) from your body. Using accessories not supplied or approved by Motorola may cause your mobile device to exceed RF energy exposure guidelines. For a list of Motorola-supplied or approved accessories, visit our Web site at: www.motorola.com.
Implantable Medical Devices
If you have an implantable medical device, such as a pacemaker or defibrillator, consult your physician before using this mobile device. Persons with implantable medical devices should observe the following precautions: ALWAYS keep the mobile device more than 20 centimeters (8 inches) from the implantable medical device when the mobile device is turned ON. DO NOT carry the mobile device in the breast pocket. Use the ear opposite the implantable medical device to minimize the potential for interference. Turn OFF the mobile device immediately if you have any reason to suspect that interference is taking place. Read and follow the directions from the manufacturer of your implantable medical device. If you have any questions about using your mobile device with your implantable medical device, consult your health care provider.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference from external sources if inadequately shielded, designed, or otherwise configured for RF energy compatibility. In some circumstances your mobile device may cause interference with other devices.
Follow Instructions to Avoid Interference Problems
Turn off your mobile device in any location where posted notices instruct you to do so. In an aircraft, turn off your mobile device whenever instructed to do so by airline staff. If your mobile device offers an airplane mode or similar feature, consult airline staff about using it in flight.

make a call 15, 17 master clear 62 master reset 61 menu 3, 60, 61 menu icons 30, 61 menu indicator 30 menu key 1, 10, 30 message reading 24, 57 sending 23, 57 message indicator 24, 32 message key 1 message reminders 60 micro-browser 58, 70 mini-USB port 2, 14
navigation key 1, 10, 37 network settings 66 notepad 46 number. See phone number numeric entry mode 36
1-touch dial 48 open to answer 43 optional accessory 10 optional feature 10
photo 18, 69 picture 69 picture ID 19, 47, 53, 54 PIN code 15, 38, 68 PIN2 code 38, 51 power key 1, 15 printing 26, 56
ring style indicator 32 ringer ID 47, 53, 55, 60 ringer volume 37, 60 ringtone 40, 53, 69 roam indicator 31
software update 29, 66 speakerphone 64 speed dial 48, 50 stereo headset 2 store phone numbers 16, 53 store your phone number 17 support 71 symbol entry mode 36 sync 65
safety information 76 safety tips 89 screen saver 41 security code 38 send key 1, 15 service dial 51 shortcuts 61 signal strength indicator 31 silent mode 37, 40 SIM Blocked message 15, 68 SIM card 11, 15, 38, 51, 68 skin 42 smart key 1, 2, 37, 61 soft keys 1, 30, 61
quick dial 52 quick note 23, 57
tap text entry mode 35 technical support 71 telephone number. See phone number text entry 33 text messaging 57 theme 42 time 41 timers 62, 63 transfer a call 50
received calls 44 recent calls 44 redial 45 reminders 60 repairs 71 resolution 19, 21 return a call 46 ring style 37, 40
TTY device 51 turn on/off 15
wallpaper 41 warranty 81 Web sessions 70 WHO information 86
unlock application 68 phone 15, 39 SIM card 68 unlock code 38, 39

your phone number 17

vibrate mode 37, 40 video 20, 69 voice dial 64 voice key 1, 2 voice record 67 voicemail 49 voicemail message indicator 32, 49 volume 37, 60 volume keys 1, 2, 37

www.motorola.com

6809517A52-O