RF Operational Characteristics
Your Personal Communicator contains a transmitter and a receiver. When it is ON, it receives and transmits radio frequency (RF) energy. The Personal Communicator operates in the frequency range of 900 MHz to 1990 MHz and employs digital modulation techniques. When you communicate with your Personal Communicator, the system handling your call controls the power level at which your personal communicator transmits. The output power level typically may vary over a range from 0.063 watts to 1.58 watts.
Portable Personal Communicator Operation and EME Exposure
Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the Personal Communicator and may violate FCC and/or other applicable regulations. DO NOT hold the antenna when the Personal Communicator is IN USE. Holding the antenna affects call quality and may cause the Personal Communicator to operate at a higher power level than needed. Phone Operation The Personal Communicator is designed to be used with a headset for talking and listening. The Personal Communicator can also be placed inside the holster, then the holster can be clipped onto your belt, pocket, handbag, or other apparel and used with the headset. Body-worn Operation To maintain compliance with FCC RF exposure guidelines, if you wear the Personal Communicator on your body when transmitting, always place the Personal Communicator in a Motorola supplied or approved clip, holder, holster, case, or body harness. Use of non-Motorola-approved accessories may exceed FCC RF exposure guidelines. If you do not use a body-worn accessory, ensure the antenna is at least one inch (2.5 cm) from your body when transmitting. Approved Accessories For a list of approved Motorola accessories, look in the accessory section of this manual.
Electromagnetic Interference/Compatibility
Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your Personal Communicator in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your Personal Communicator when on board an aircraft. Any use of a Personal Communicator must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 centimetres) be maintained between a handheld wireless phone and a pacemaker. These recommendations are consistent with the independent research by, and recommendations of, Wireless Technology Research. Persons with pacemakers should: ALWAYS keep the Personal Communicator more than six inches (15 centimeters) from their pacemaker when the Personal Communicator is turned ON. not carry the Personal Communicator in the breast pocket.

Operational Cautions

Antennas Do not use the Personal Communicator if it has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewellery, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.
European Union Directives Conformance Statement
This product is in conformance with the requirements of the applicable EU Council Directives. Declarations of Conformance with the requirements are located at: Motorola Ltd. Personal Communications Sector Europe, Middle East and Africa Midpoint, Alenon Link Basingstoke, Hampshire RG21 7PL United Kingdom
APPROVED for connection to telecommunications systems specified in the instructions for use subject to the conditions set out in them. S/1357/4/V/503894

Special Keys

S O C E $ <> , f Turns the phone on and off. Accept call, setting, option. Reject call, setting, option. Enter the Quick Access menu. Press to access the Options and Phone Book menus. Press to select entries and menu options. Press to add a phone book entry. Press to call Voicemail. To end a call, press = for 1.5 seconds and then quickly press = again. To make a call, enter or recall a number and then press and hold = for 1.5 seconds.

Volume Buttons

The Volume buttons are on the left-hand side of your phone, above and below the Smart button. The buttons are used for adjusting the keypad, earpiece and ringer volume. A volume meter will display the current volume setting. The meter will disappear after a short time, or if you press O or C. To adjust the keypad and earpiece volume, press the buttons with no other features selected. To adjust the ringer volume, first select the Adjust Ring Volume option in the Phone Setup Menu and then use the buttons to set the required volume. The volume buttons can also be used to scroll though the Phone Book entries after pressing the Smart button. AIf you receive a call and you do not want to answer it immediately, you can press either of the volume buttons to stop the phone from ringing or vibrating. This will not answer the call.

The Smart Button

The Smart button (=) is on the left hand side of your phone in-between the two volume keys. Press it to quickly access all your Phone Book entries, and then either scroll through the entries using the volume buttons or press one of the alphanumeric keys to search for a specific name - for example, press 7 to search for the name Pam, or press 7 four times to search for the name Sam. AIf a Phone Book entry does not have a name, it will not be displayed. If you are using the optional headset, you can also use the Smart button to make, answer and end calls as follows: To answer a call, press = for 1.5 seconds.

Your Battery

Charging a New Battery
New batteries are supplied in a totally uncharged state. To ensure maximum battery performance, a new battery (or battery that has not been used for several months) should be charged for at least 14 hours before use. AA new battery will require several full charge/discharge cycles in order to achieve its optimum performance. AA new battery, or a battery that has not been used for several months, may cause a premature fully charged indication. Ignore this indication and let the battery charge for several more hours, remove and re-insert the battery into the charger, and charge for an additional 14 hours.

The Status Indicator

The status indicator on the top of the phone provides you with the following information:
Incoming Call In Service No Service Roaming Alternate Red/Green Flashing Green Flashing Red Flashing Yellow
Important Battery Information
! Always treat your batteries with care. See Batteries, at the beginning of this manual. ! Never leave your battery in extremely high temperatures (over 60C), for example behind glass in very hot, direct sunlight. ! Only Motorola Original Accessory batteries can be charged in the phone or the optional desktop charger. This is to protect you and your phone from the risks of incorrect charging. ADo not use lithium ion batteries at extremely low temperatures as the maximum standby/talk time will not be available when cold.
To ensure that you enjoy maximum battery life and use your battery to its fullest capacity: The battery should be at or near room temperature when charging.

Removing Your Battery

! Switch off your phone before removing the battery. Failure to do so may damage your phone memory. 1 Press the release catch on the battery compartment and lift off the cover. 2 Push the battery towards the top of the phone and lift the battery out from the bottom end.
Battery Performance and Maintenance
Best battery performance will be achieved when you regularly charge and discharge batteries as instructed in this manual. Battery performance is greatly affected by network coverage. Set Battery Saving Mode to On (see Phone Setup Menu) and/or Frequency of Search to Slow or Medium (see Network Selection Menu). If left unused, a fully charged battery will discharge itself in approximately one month. When not in use, store your battery uncharged in a cool, dark and dry place.

The battery is being charged.
Fast charging is complete.
Battery may be defective, or may not be a Motorola original battery.
This message is accompanied by a single beep. Your phone is alerting you that you do not have charging capabilities with this battery even though the battery may be able to power the phone. The most likely reason why your charging system does not recognise the battery is that the battery you have purchased is not a Motorola original battery and therefore does not have the communications technology built into it. All Motorola original batteries include this communications technology. It is recommended that you use only Motorola original batteries, chargers and other accessories.

Your SIM Card

Your SIM (Subscriber Identity Module) card was supplied by your Cellular Service Provider when you bought your phone. You will not be able to make or receive calls if you do not have a SIM card inserted in your phone. ASome networks allow you to make emergency calls without a SIM card inserted. The SIM card is a Smart Card that contains your phone number, service details and memory for storing Phone Book numbers and messages. You can therefore use your SIM card in someone elses GSM phone and you will be charged for the call. Like a bank or credit card, you should keep your SIM card secure. Do not bend or scratch your card and avoid exposure to static electricity or water. ! Switch off your phone before inserting or removing the SIM card. Failure to do so may damage the memory on your SIM card. 4 Insert the SIM card into the holder as shown. The SIM card should be inserted with the notch at the top and facing towards the base of the phone.
SIM Card Insertion/Removal
1 Switch off your phone by pressing and holding the S key, remove the battery cover and the battery. 2 Slide the SIM holder towards the right and lift up the left side of the holder. 3 Remove the SIM card from the holder if necessary.
5 Replace the holder and press and slide it to the left to lock it into place. 6 Replace the battery and battery cover. If the SIM card is inserted the wrong way round, or damaged, the Check Card message may be displayed. Remove the SIM card, check that it is the right way round and then re-insert it into the phone. If either of the Bad Card See Supplier or Blocked See Supplier messages are displayed, then you will need to contact your Cellular Service Provider.

GSM Emergency Calls

The world-wide GSM standard provides a single, uniform number, 112, to dial in cases of emergency. Provided that your phone has found a network, you will be able to make an emergency call. The call can be made regardless of any security codes and, depending on the network, with or without a SIM card inserted. The emergency call will be directed to a central emergency operator. To dial the GSM emergency number, press 112O. While the emergency call is being made and connected, the display will show Emergency Calling. AEmergency calls can be made without a battery fitted if the phone is powered by the travel charger.

Receiving a Phone Call

To receive a phone call: Your phone must be switched on and unlocked. You must be in an area where there is GSM 900/1800 service. Your Call Diversion and Call Barring settings should not be set to divert or bar incoming calls. When your phone receives a call, it will ring or vibrate and the display will show the Call message (if you have Caller Line Identification, the callers number or name will be displayed instead). Normally, the call is answered as soon as the phone is opened. However, if the Key Answer Only option is selected, opening the phone will not answer the call - you will have to press a key. When the identification is displayed, you can decide whether or not to answer the call by pressing O, a numeric key (1 to 9), < or >. To set this option, see Key Answer Only. You can also answer using the keys if the phone rings whilst the phone is already open. If your phone is open and you do not want to answer the call, you can: Press and release the C key. If you have enabled the 'Detailed Diverting - If Busy' or Divert when unavailable options in the Options Menu, the caller will be diverted to the forwarding number, otherwise the caller will hear the busy tone. or Press and hold the C key. This will reject the incoming call. No call divert option will be offered. If your phone rings and you do not answer it, the message Unanswered Call will be displayed to show you that a call attempt was received.

Ending a Phone Call

Add or Edit Voice Tag and Delete Voice Tag Use these options to add, edit or delete the Voice Tag for the Phone Book entry. See Using Voice Control. Add Entry i Press E. Select the Quick Access feature (T Add to SIM? or F Add to Phone?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. This option is used to add (store) entries to the Phone Book. You can choose to add the new entry to either the phone or SIM card memory locations. Add To Phone Memory, Add To SIM Card Memory Once you have selected the destination of the new entry, you will be asked to enter the telephone number, name and location number of the new entry. The last telephone number displayed will be presented by default; it can be used or discarded as required. If the entered location is not valid, a timed message Range YYY-ZZZ will be displayed and the phone will return to the Enter Location prompt. If the chosen location is currently used by another entry, you will be asked for confirmation that the location can be overwritten. If you do not supply a location number, the next available location will be used. When the new entry has been entered, a timed message Stored XXX will be displayed.
Add Voice Tag If you add a Phone Book entry to the phone memory, the Add Voice Tag? prompt appears after Stored XXX. Press O to add a Voice Tag. See Using Voice Control. Check Capacity This option is used to check the number of free Phone Book entries in the phone or SIM card memory areas. Check Phone Capacity, Check SIM Capacity Once selected, a timed message XX Unused Locations displays the requested information. Prevent Access This option enables you to prevent access to the Personal Numbers list. AYou cannot record a Voice Tag if you have set Prevent Access To Phone Memory. To SIM Card Memory, To Phone Memory, To Phone & SIM Memory, No Memory Restrictions You can prevent access to all entries in the SIM card memory, the phone memory or both the phone and SIM card memory. To cancel all access restrictions use the No Memory Restrictions option. When you change the restrictions, you will be requested to enter the Security Code before the change is made.

Show Services

i Press E. Select the Quick Access feature (e Show Services?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. This option displays a list of phone numbers and services provided by your Cellular Service Provider. AAvailability depends on the type and settings of the SIM card, and/or your subscription to this feature.

Last Ten Calls

These options allow you to review your most recently used phone numbers. Depending on the option you choose, you can then redial a phone number, store a phone number in your phone book, or erase all of the phone numbers. After you select an option, use the < or > key to scroll through the list of phone numbers. Press the O key to proceed. AYou can use postscripting to modify a number once you have retrieved it from either of the Last Ten Calls lists. Last Calls Made Select this option to redial the phone number of any one of the last ten calls made.
Last Calls Received i Press E. Select the Quick Access feature (W Received Calls?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. Select this option to redial the phone number of any one of the last ten calls received. In addition, you can add time and date information to one call, and you can store any of the phone numbers in your phone book. AYou will only see numbers in the Last Calls Received list if you have Caller Line Identification. When you scroll through your last ten calls, each call appears with a call position number, for example:1+, 2-, 3+. 10+. A + symbol indicates that you answered the call. A - symbol indicates that you did not answer the call. Press the O key to select a phone number. You can then scroll through and select one of the following options: Call Number Select this option to call the phone number. Time and Date Select this option to add a time and date stamp to the phone number. Press the O key to accept the date and time stamp and return to the list of last ten calls received.
Add to Phone Memory Select this option to add all the phone number details (including any details you have added) to your phone memory. If the name in the received call does not appear in your phone book, the phone prompts you to Enter Name and Enter Location. For further details, see 'Add Entry' in this section. Add to SIM Card Memory Select this option to add the phone number details (including any details you have added) to your SIM card memory. If the name in the received call does not appear in your phone book, the phone prompts you to Enter Name and Enter Location. For further details, see 'Add Entry' in this section. Erase All Numbers This option erases all the numbers stored in your Last Ten Calls Made and Last Ten Calls Received lists. AThe Last Ten Calls lists will be erased when a new SIM is inserted in the phone.

After selecting any of the call divert options there will be a short delay while the phone asks the network for the current setting. Divert Voice Calls This option will allow you to set your phone to Divert When Unavailable, Divert All Voice Calls or Detailed Diverting. Divert When Unavailable This option will enable you to divert all incoming Voice calls to a single number, whenever your phone is unavailable. The option has two settings, On or Off. If you change the setting to On, you will be asked to enter a diversion phone number using the digit keys. ASetting Divert When Unavailable to On will have the same effect as setting all Detailed Diverting options to On. AWhen On, Divert When Unavailable takes priority over detailed diversion settings. Divert All Voice Calls i Press E. Select the Quick Access feature (P Divert On/ Off?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. This option will enable you to unconditionally divert all incoming Voice calls to a single number. The option has two settings, On or Off. If you change the setting to On, you will be asked to enter a diversion phone number using the digit keys.
AWhen On, Divert All Voice Calls takes priority over all other Voice call diversion settings. Detailed Diverting These options will enable you to divert Voice calls to different numbers, depending upon the current status of your phone. Each of the following detailed diverting options operate in the same way. Each option has two settings, On or Off. If you change the setting to On, you will be asked to enter a diversion phone number using the digit keys. ADetailed diversion settings are ignored while Divert All Voice Calls or Divert When Unavailable are On. If Busy This option will divert incoming calls if your phone is busy. If Not Reachable This option will divert incoming calls if your phone cannot be contacted by the network. If No Answer This option will divert incoming calls if you do not answer the call.
Divert Fax Calls This option will enable you to divert all Fax calls to a single number. The option has two settings, On or Off. If you change the setting to On, you will be asked to enter a diversion phone number using the digit keys. Divert Data Calls This option will enable you to divert all Data calls to a single number. The option has two settings, On or Off. If you change the setting to On, you will be asked to enter a diversion phone number using the digit keys. Cancel All Diverting This option will enable you to cancel the diversion of incoming calls. ! This option resets all diversion settings to Off and removes all diversion numbers.

Your phone supports the two GSM message features: Short Message Services (SMS) and Cell Broadcast.
Cell Broadcast Messages These are general messages, broadcast to a group of phones and can only be received when your phone is in standby mode. These messages are broadcast in numbered 'channels' and, in general, each channel will tend to carry one particular type of information. Typical cell broadcast channels could have information on local weather conditions, traffic reports or stock market prices. Please contact your network operator for a list of available channels and the information they supply. When the message has scrolled across the display, the beginning of the message will be shown until you either remove it or a new message arrives.
How to Create and Edit SMS Messages
Use the Message Editor to create or modify text messages. When you enter the editor, the last message that was edited will be displayed. Press and hold C to clear the message and start a new one, or modify the message displayed. For an explanation of how to enter text, see How to Enter Alphabetic Characters. Press O once you have completed your message. You will then be presented with the following options: Send Message - If you select this option you will be prompted for a phone number, enter the number and then press O to send the message. Store Message - Select this option to store your edited message in your Outgoing Messages list. AIf you dont store the message after it has been edited, you will lose all your changes as soon as you select another message to be edited.

How to Read SMS Messages

You can use the scroll keys (< and >) to scroll through messages in either the Received Messages or Outgoing Messages lists. To display a specific message, enter the message number, for example press 5 to display the 5th message. If the message does not exist, Invalid Msg Number will be displayed. Alternatively, to display the next message, press O and select Go To Next Message.

j Call Voicemail

i Press E. Select the Quick Access feature (R Call Voicemail?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. This option will make a call to the current voicemail number. You can also press f to call the Voicemail number. The voicemail number is entered using the Voicemail Number option in the Message Settings menu.

Find Entry by Name - this allows you to recall a phone number from the Phone Book by name and send the message (see Find Entry by Name in the Phone Book section). Find Entry by Location - this allows you to recall a phone number from the Phone Book by location and send the message (see Find Entry by Location in the Phone Book section). Edit Message This option allows you to use the Message Editor to edit the selected message and then to either send the modified message or store it in your Outgoing Messages list. See How to Create and Edit SMS Messages for more information on using the Message Editor. Delete Message This option will delete the currently viewed message. Go to Next Message This option will display the next outgoing message.
This option allows you to add the destination phone number using a sub-menu. Using the scroll keys you can select: Enter Number - this allows you to manually enter the phone number using the keypad and send the message.

Message Editor

i Press E. Select the Quick Access feature (a Message Editor?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. The Message Editor is used to edit the currently selected message and then to either send the modified message or store it in your Outgoing Messages list. See How to Create and Edit SMS Messages for more information on using the Message Editor.

Cell Broadcast

This option is used to set the cell broadcast settings. The option has two settings On or Off. If you change the setting to On, you will be asked to enter the channel you wish to receive information from. Please contact your Cellular Service Provider for a list of available channels and the information they provide. While a broadcast message is scrolling across the display you can stop and start it by pressing <. Press > to restart the message from the beginning. If you want to remove the message from the display, press C. AIf you need to use the < and > keys for their normal functions while you are receiving a cell broadcast message, you must first remove the message.

These options determine how often your phone tries to register with a network and how the attempt is made. Registration Preferences This option determines how the phone tries to register with a network. The option has two settings, Automatic Search or Manual Search.

j Preferred Networks

Add Network to List This option enables you to add networks to your preferred list. When selected, the 'Choose From Available' option will scan to see which networks are operating in your current location. When the scan is complete, press the $ key to scroll through the list. When you see a network you wish to store in your preferred list, press the O key. You will be asked where the selected network is to be located in the preferred list. The 'Choose From Known' option will, when selected, present you with a preset list of networks. Press the $ key to scroll through the list. When you see a network you wish to store in your preferred list, press the O key. You will be asked where the selected network is to be located in the preferred list. Select the 'Add New Network Code' option to enter network codes directly. Once entered, you will be asked where the network is to be located in the preferred list. Show List of Networks This option is used to display the networks you have stored in your preferred list. In addition, pressing the O key will select the currently displayed entry and enter a move/delete sub-menu. When 'Move to New Location' is selected you will be asked to enter a new location for the selected network. When selected, 'Delete Selection' will remove the selected network from the preferred list.

Find New Network

i Press E. Select the Quick Access feature ( Find New Network?) or after the tone, say the Voice Tag name. See Voice Control for Quick Access Features. When selected, the phone will try to register with a network in the normal manner, with one exception. When the registration attempt is made, your current network will be excluded from the list of those available. If the attempt fails, your phone will then try to re-register with the previous network.

Call Meters Menu

Call Metering
Your phone has an internal metering system which can be used to provide you with individual and total call times or costs. ACall cost information is only available if you receive the Advice of Charge service. If you do not receive this service, then only time meters are available. The meter can be displayed during a phone call and audible tones can be generated to indicate the passage of call time. Your phone can handle values up to 21 digits long, although during calls it can only display the last 12 digits. If the value exceeds 21 digits, then Too Large is displayed. In addition, you can set a maximum charge limit so that your phone will monitor either the number of units used or the call cost, and then not allow the limit to be exceeded.

B Find Name?

You will be prompted to Enter Name. Enter the first three characters of the name and press O. The first matching entry in the Phone Book will be displayed. Press O to call the number.
AThe menu shown above represents the default setting supplied with your phone.

T Add to SIM?

You will be prompted to enter a phone number and then a name. AIf you already had a number displayed, it will automatically be re-displayed when you select this feature. The number will be stored in the next available SIM card location. Add or Edit Voice Tag and Delete Voice Tag for more information.

K Read Messages?

Your newest message will be displayed; you can then read, delete and edit messages as normal. See Received Messages for more information.

L Vibrate On/Off?

VibraCall will be switched either on or off depending on the current setting. If VibraCall is switched on, the Ring or Vibrate setting changes to Vibrate Only. If VibraCall is switched off, the Ring or Vibrate setting changes to Ring Only. See j Ring or Vibrate for more information.

R Call Voicemail?

Your phone will make a call to your voicemail number. AYou must have defined a Voicemail number in order to use this feature. See Call Voicemail for more information.

P Divert On/Off?

Unconditional voice call diversion will be switched either on or off depending on the current setting. This will allow Fax and Data diversion to remain enabled independent of the Voice Call Diversion setting. AYou must have defined a diversion number using the Divert All Voice Calls option in the Call Diverting menu in order to use this feature. AYou cannot switch call diverting on or off if you are outside network coverage.

G Battery Meter?

A bar graph indicating the approximate battery charge level will be displayed. The more bars displayed, the greater the charge level. Show Battery Meter for more information.

} Play VoiceNotes?

Plays the recorded VoiceNotes. See Using VoiceNotes for more information.

D Find Location?

You will be prompted to Enter Location. Enter the location number and press O. The first matching entry in the Phone Book will be displayed. Press O to call the number.

N Adjust Ring?

This option is used to display and to set the incoming call ring tone volume.

F Add to Phone?

You will be prompted to enter a phone number and then a name. AIf you already had a number displayed, it will automatically be re-displayed when you select this feature. The number will be stored in the next available phone memory location. Add or Edit Voice Tag and Delete Voice Tag for more information.

The battery wont charge

Check the charger. Is it properly connected? Are its contacts clean and dry? See Your Battery. Check the battery contacts. Are they clean and dry? Check the battery temperature. If it is warm, let it cool before recharging. Is it an old battery? Battery performance will decline after several years use. Replace the battery. Are you using a Motorola original battery? Your charging system may not be able to communicate with your battery. See Your Battery.
The battery icon and meter are missing The battery drains faster than normal
Are you using a Motorola original battery? Your charging system may not be able to communicate with your battery. See Your Battery. Are you in an area of variable coverage? This uses extra battery power. Is it a new battery? A new battery will need two to three charge/discharge cycles to attain normal performance. See Charging a New Battery Is it an old battery? Battery performance will decline after several years use. Replace the battery. Is it a battery that hasnt been completely discharged? Allow the battery to fully discharge (until the phone turns itself off) and then charge the battery overnight. Check that the Frequency Of Search feature in the Network Selection menu has not been set to Fast or Continuous. See Network Search. Check that the Battery Saving Mode feature has not been set to Off. Are you using your phone in extreme temperatures? At extreme hot or cold temperatures, battery performance is significantly reduced.
You cant cancel Call Diverting or Call Barring The o symbol is flashing I cant make international calls
Wait until you are in an area with good network coverage and try again. There is not enough memory available to store another SMS message. Use the Messages menu to delete one or more existing messages. Some Service Providers automatically bar the ability to make international calls. Contact your Service Provider. Have you included the relevant codes? Press and hold the 0 key to display the international dialling prefix (+) and then enter the appropriate country code followed by the phone number.
Accessories..87 Accessory setup menu.79 Add entry To phone memory.. 48, 83 To SIM card memory.. 48, 83 Adjust Contrast.68 Adjust ring volume.66 Alert tones..67 Assign Key to Feature..40 Automatic answer..79 Automatic Handsfree..79 Automatic lock..67 Automatic redial..24 Auxiliary alert..80 Available networks.73 Blocked message.. 23, 69 Buttons Smart button..15 Start/Stop Record..15 Volume..15 Conference Call..29 Call Waiting.33 Hold Call...28 Make a New Call..28 Reconnect..29 Reconnect Held Call.29 Restrict My Number..28 Split Call..29 Switch Calls..29 Contrast Adjust Contrast.68 adjusting...84
Call charge settings..77 Call diverting.. 54, 82 Call holding...30 Call metering..75 Call meters menu..75 Call related features menu.53 Call timers..76 Call Transfer...33 Call Voicemail..60 Call waiting..30 Calling a number..24 Cancel all diverting. 56, 82 Capacity Checking battery capacity.53 Checking Phone Book capacity.49 Cell broadcast..63 Messages..60 Change bar password.58 Change SIM PIN2 code..69 Change unlock code..67 Characters..46 Charge meters Resetting...77 Check capacity (of the Phone Book)..49

Credits concept Maxime Chanson graphic design Chic / Stereochromie packshot Pierre-Yves Toledano BACK TO BASICS lkkicopyright 2010
Lkki offers a range of vintage, revamped mobile phones, fun and coloured. Our selection brings together the most legendary handsets of the 90s! With their original designs and basic features, these retro mobile phones have rediscovered their beauty thanks to a new glossy paint available in 4 technicolors. More than 10 years after their releases, here they are, back to business, with a strong message: BACK TO BASICS! Too many online social networks and an excess of e-mail and applications, have made us slaves to technology in our everyday lives. But Lkki provides a solution, allowing a return to the basic features: phoning and texting. Simple, but effective. Finally, by customizing revamped second-hand mobile phones, Lkki makes a commitment to sustainable development and recycling, through putting iconic objects from the past back into service. Discover our polyphonic coloured mobile phones!
Lkki is not an authorized reseller of Motorola products. Products available on lekki.fr are aftermarket customised and revamped mobile phones. Motorola StarTAC, V3690 and Nokia 3210-8210 are registered trademark of Motorola and Nokia.
lkki back to basics motorola Startac
General characteristic model StarTAC130 network GSM 900 announced 1998 weight 95g S.A.R 0,34 antenna retractable Features alert types vibration and monophonic ringtones phonebook 100 intern + 100 sim messaging sms battery 48h stand-by and 120 mn talk time Accessories battery charger belt clip

nokia 3210

General characteristic model 3210 network GSM 900 / 1800 announced 1999 weight 151g S.A.R. 0,81 Features alert types monophonic ringtones, vibration phonebook 100 intern + 100 sim messaging sms T9 games snake, rotation, memory other alarm, calculator battery stand-by 200h Accessories battery charger

motorola v3690

General characteristic model V3690 network GSM 900 / 1800 announced 1999 weight 86g S.A.R 1,1 Features alert types vibration, monophonic ringtones phonebook 100 intern + 100 sim messaging sms battery stand-by 140h - talking 200 min Accessories battery charger

nokia 8210

General characteristic model 8210 network GSM 900 / 1800 announced 1999 weight 79g S.A.R 1,00 Features alert types monophonic ringtones, vibration phonebook 200 intern + 100 sim messaging sms T9 games snake, rotation, memory other alarm, calculator battery stand-by 120h Accessories battery charger

www.lekki.fr

A NEW RECYCLING OPPORTUNITY
Lkki is based on an original concept of sustainable development. Although the average lifespan of a handset is just 18 months, it takes between five and seven years to counteract the carbon emissions produced: from the extraction of raw materials to recycling. So, to effectively reduce the carbon footprint of a mobile phone, it is necessary to prolong the duration of its use. That is why Lkki offers a fresh alternative to the problem by refurbishing and by customizing vintage mobile phones.

GIMME more

As the prolonged life expectancy of a telephone is not enough, Lkki also makes a commitment in favour of recycling, with the take-back programme Gimme More. From the date of purchase, the user has 24 months to return his mobile phone in order to recycle it within a clean network. A purchase voucher of 15 will be offered in return.

action carbonE

The current economic model, based on potentially infinite growth, is today displaying its weaknesses and threats to the environment. That is why Lkki makes a further commitment by compensating the completeness of its carbon footprint. Through the programme Action Carbone, created by the foundation GoodPlanet and chaired by Yann Arthus-Bertrand, every phone customized by Lkki is the object of financial compensation. This support allows us to finance and to accompany associative and community projects of emissions reduction in developing countries. For more information: www. actioncarbone.org.

>Lkki, laureate of the Green Challenge 2010 Dooz-BFM Radio.
Lkki pack back to basics vintage phone

back to basics

www.lekki.fr hello@lekki.fr