B2-Series Hands-free Module

User Manual

en da de es fr fc it
with Bluetooth wireless technology

F-Series | N-Series

B2 User Manual | Important safety information
2007 Brunswick New Technologies Asia Pte Limited. Navman is a registered trademark of Brunswick New Technologies Asia Pte Limited and is used under licence by Navman New Zealand. Navman is part of the Brunswick Corporation, headquarters Chicago, IL. All rights reserved. The software contains proprietary information of Navman; it is provided under a licence agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Navman. Back-On-Track, Drive-Away, NavPix, Smart and Turn-by-Turn are either registered trademarks or trademarks of Brunswick New Technologies Asia Pte Limited and are used under licence by Navman New Zealand. All rights reserved. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Navman New Zealand is under license. Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All rights reserved. All other trademarks and registrations are the property of their respective owners. Published in New Zealand.

Disclaimer

Due to continued product development this information may change without notice. Navman does not warrant that this document is error-free. The screenshots and other presentations shown in this manual may differ from the actual screens and presentations generated by the actual product. All such differences are minor and the actual product will deliver the described functionality as presented in this User Manual in all material respects.

Compliance

WARNING This product, its packaging and its components contain chemicals known to the State of California to cause cancer, birth defects or reproductive harm. This Notice is being provided in accordance with Californias Proposition 65. The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important safety information
Removing original equipment, adding accessories or modifying your vehicle could affect the vehicles safety or make it illegal to operate in some jurisdictions. Follow all product instructions and all instructions in your vehicle owners manual regarding accessories or modifications. Consult your countrys and/or states laws regarding operation of a vehicle with any accessories or modifications. Do not mount the B2 or attach the antenna in a way that may interfere with the driver's view, the safe operation of the vehicle, deployment of air bags or other safety equipment. Do not attempt to attach the B2 or attach or adjust the antenna while driving. Before you use the B2 for the first time, familiarize yourself with your device and its operation.

Do not handle the B2 while it is hot. Let the product cool, out of direct sunlight.
Do not expose the B2 to direct sunlight in an unattended vehicle for prolonged periods. Overheating may damage the unit. To discourage theft, do not leave the B2, mounting bracket or any cables in plain view in an unattended vehicle. Failure to adhere to these warnings and cautions may lead to death, serious injury or property damage. Navman disclaims all liability for installation or use of the B2 that causes or contributes to death, injury or property damage or that violates any law.

B2 User Manual | Welcome

Welcome
Thank you for purchasing the Navman B2 module. The B2 attaches to your Navman mounting bracket to provide you with Bluetooth hands-free access to your mobile phone or PDA while driving. Use this manual to learn how to operate your B2 efficiently and safely, and discover the range of features available to you.

Traffic

If your B2 has traffic capability, see the applicable traffic user manual on the enclosed CD. To install the traffic antenna in your vehicle, see the enclosed In-Car Installation Guide.

Box Contents

B2 module
Traffic antenna including: Traffic FM Antenna 4 FM antenna fixing pads (including two for second vehicle) Note: The antenna and fixing pads are only supplied with models that support traffic.
CD containing: Traffic User Manuals Adobe Reader 7 Note: The CD is only supplied with models that support traffic.
Documentation including: B2 User Manual In-Car Installation Guide Limited Warranty Agreement
B2 User Manual | Getting to know the B2

Getting to know the B2

This section describes the components of your B2. Not all features are available on all models. We recommend that you familiarize yourself with your B2's basic operations before use.

Component

Hot shoe plate Microphone

Description

Connection plate for your Navman. Receives conversation and voice commands. Begins a call using voice recognition Accepts incoming calls Selects Voice Menu options Redials last number called Changes between two calls Changes call from B2 to phone or PDA, and back again. Note: If you have not recorded any keywords, pressing Record keywords section of the Voice Menu. will access the

Control switch

Accesses and navigates the Voice Menu. It can be pushed left or right, or pressed (like a button). Press to access the Voice Menu Push left or right to navigate through the options, then press to select an option Press to select Voice Menu options Push left or right during a call to adjust volume. Ends calls Rejects incoming calls Exits the Voice Menu and sub-menus. Connection socket for the traffic antenna which allows the B2 to receive TMC traffic signals. Note: Only applicable for models that support traffic. USB connection socket for the following: AC power-pack to supply power from the mains/line power when updating software In-vehicle power adaptor to supply power from the vehicle power socket USB cable to connect to your computer when updating software (do not make or receive a call while connected to your computer via USB cable). Note: The AC power-pack, in-vehicle power adaptor and USB cable may have been supplied with your B2, depending on the model. They are also sold separately. Socket for external microphone (external microphone sold separately).
B2 User Manual | Getting Started

Getting Started

Before you can use the B2 to provide hands-free access to your mobile phone or PDA, you must establish a secure connection between both devices. This process is called "pairing".
How do I pair the B2 with my phone or PDA?
WARNING NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA: State law prohibits drivers in California and Minnesota from mounting objects on their windshields while driving. Other Navman mounting options are recommended and an alternative mounting option is included in this box. Navman does not take any responsibility for any fines, penalties, or damages that maybe incurred as a result of disregarding this notice. See California Vehicle Code Section 26708(a); Minnesota Statutes 2005, Section 169.71.
Position the Navman and B2 in your vehicle according to the instructions in the In-Car Installation Guide. Ensure the in-car vehicle adaptor (supplied with your Navman) is plugged into the B2 socket.
Caution: Please ensure that the B2 does not obstruct the driver's view, or interfere with the operation of the vehicle airbags and safety devices. 2. If you are pairing with a phone or PDA that supports the Bluetooth Hands-free profile, continue to step 3. If you are pairing with a phone or PDA that only supports the Bluetooth Headset profile, press and hold + Control switch for three seconds. The and buttons will both flash. The B2 will be visible to all Bluetooth devices for 3 minutes. Turn on Bluetooth on your phone or PDA, then search for near-by Bluetooth devices. For more information on searching for Bluetooth devices, see the user manual supplied with your phone or PDA. 4. Select Navman B2-Series from the list of local Bluetooth devices. If you are prompted for a passkey or device PIN, enter 1234. When pairing has completed, the B2 will say "Pairing successful". From now on, when the B2 is turned on, it will automatically detect and pair with your phone or PDA if it is in close proximity (if you have paired the B2 with more than one phone or PDA, it will pair with the one most recently used). The B2 will beep when successfully paired with your phone or PDA. Note: Your language will be automatically selected on the B2 if your phone or PDA supports this feature; otherwise, you can select the language yourself (see "Voice Menu" on page 10).

How many devices can I pair with my B2?
You can pair up to five phones or PDAs with your B2, although only one phone or PDA may be paired with the B2 at any one time. If you attempt to pair a sixth phone or PDA, you will hear the message "Memory full". To clear the memory, you must press and hold + for three seconds. Note: Clearing the memory will delete all contacts and keywords.
B2 User Manual | Basic functions

Basic functions

Note: The use of voice recognition, redial and changing calls between the B2 and your phone or PDA, depend on the model of phone or PDA you are using.

Making a call manually

Enter the number using your phone or PDA, then start the call. The call will automatically change to hands-free mode using the B2. Note: If the call does not change to the B2, press.
Making a call using voice recognition
Before you can make a call using voice recognition, you must have first recorded the correct keywords (see "Voice recognition" on page 11) and added at least one contact to the B2. 1. 2. 3. Press.
After the beep, clearly say the name of the person you want to call. If the contact has more than one number assigned to it, clearly say the category of the number after the second beep, for example, "home", "work", "cellular", etc.
The B2 will place the call via your phone or PDA.

Receiving a call

When an incoming call is received on the B2, you will hear a ringtone and see the and buttons flash. Note: Some versions of the Navman F-Series models may display Caller ID information on-screen when a call is received. Press Press to answer the call. to reject the call.

Using call-waiting

When an incoming call is received while you are already on a call, you will hear a ringtone and see the buttons flashing. Press Press to change to the incoming call. Press to reject the incoming call.
again to change between calls.

Ending a call

To end a call, press. to end the current call. When using call-waiting, press

Redialling the last number you called
To redial the number you last called, press and hold for two seconds.

Adjusting the volume

The B2 will default to the level of volume used when it was last paired with the same phone or PDA. To adjust the volume during a call, push the Control switch right to increase volume or left to decrease volume. You can also adjust volume using the volume control on your phone or PDA. To adjust volume at other times, use the Voice Menu (see "Voice Menu" on page 10).
Changing the call to your phone or PDA
To change a call from the B2 to your phone or PDA, press You can then change the call back to the B2 by pressing. again.
Sending tone sounds for voice mail and other services
To use voice mail and other phone-based services, you can use the B2 to send tone sounds: 1. 2. 3. During a call, press the Control switch. The B2 will say "0". Push the Control switch left or right to navigate through the numbers and symbols. To send a number or symbol, push the Control switch.
B2 User Manual | Voice Menu

Voice Menu

The Voice Menu is used to configure the B2 settings. To access the Voice Menu, press the Control switch. To navigate through the menu, push the Control switch left or right. To select an option or access a sub-menu, press Note: You cannot access the Voice Menu during a call. or the Control switch.

Language

Select your preferred language for the B2. Available languages include: UK English, US English, French, Spanish, Italian, German, Dutch, Swedish and Danish.

Volume

Increase or decrease the volume of the B2. A beep will sound to indicate the volume level.

Add contact

Allows the B2 to receive contacts from your phone or PDA (see "Adding contacts to the B2" on page 12).

Record keywords

Enter spoken keywords for voice recognition (see "Voice recognition" on page 11).
Update software by Bluetooth
Allows the B2 software to be updated via Bluetooth. Updating the software can help improve performance and ensure that the B2 is compatible with the latest models of Bluetooth phones and PDAs. To update the B2, visit support.navman.com.
B2 User Manual | Voice recognition

Voice recognition

The B2 has the ability to understand spoken keywords and contact names by using voice recognition. Before you can use voice recognition, you must record the keywords.
How do I record the keywords?

1. 2. Navigate through the Voice Menu to the Record keywords sub-menu, then press When the B2 says "Record all keywords", press. again, then follow the voice prompts.
When asked to say a keyword, ensure that you speak clearly. If one or more keywords have already been recorded, the B2 will begin with the first keyword that has not yet been recorded. To skip a keyword, push the Control switch left or right. 3. You can exit the Voice Menu at any time by pressing.
B2 User Manual | Adding contacts to the B2
Adding contacts to the B2
You can make calls to your contacts using voice recognition. To do this, you must send contact information from your phone or PDA to the B2. The B2 can store information for up to 400 contacts (contacts cannot be shared between paired phones and PDAs). Note: You must record the voice recognition keywords (see "Voice recognition" on page 11) before you can send contact information to the B2.
How do I send contact numbers from my phone or PDA to the B2?
Note: You can only send contact information for one contact at a time. 1. 2. 3. Navigate through the Voice Menu to the Receive contacts sub-menu, then press. The Bluetooth connection between the B2 and your phone or PDA is disconnected. Go to the Phone book, Address book or Contact list on your phone or PDA and select the contact to send to the B2. Press Options, then Send by Bluetooth.
Note: The method of selecting and sending a contact to the B2 by Bluetooth may differ depending on your model of phone or PDA. 4. 5. Select Navman B2-Series from the list of local Bluetooth devices. If you are prompted for a passkey or device PIN, enter 1234. Follow the prompts from the B2 to record a name for the contact. The correct categories will be assigned to the contact's numbers automatically.
You can now call a contact using voice recognition.
How do I update contact numbers on my B2?
You can update the numbers assigned to a contact by resending the contact from your phone or PDA. You can not delete a contact.
B2 User Manual | Support information

Support information

Online support
For 24/7 help and support with Navman products, visit our Technical Support website at: support.navman.com You will find a fully searchable Frequently Asked Questions (FAQs) section for all Navman products. At least 90% of our customers find answers to their questions at support.navman.com, however if you require further support, you can use the online email option to contact us.

Phone support

If you would like to speak to a member of our Technical Support team, please call the following number for your region: United Kingdom, Ireland and International +44 (0) 950 Monday to Friday: 09.00 - 17.30 UK time (10.00 - 18.30 Central European Time) North America +1-866-9NAVMAN (866-962-8626) Monday to Friday: 9.00am - 6.00pm Eastern time Australia +Monday to Friday: 8.30am - 5.00pm Eastern Standard Time. New Zealand 0800 GO NAVMAN (from NZ only) Monday to Friday: 9.00am - 5.00pm

The Freedom Range New for 2007
More exibility. More freedom.
In 2006, Navman launched the Freedom F20, one of the top-selling car navigators in Europe. Building on that success, Navman introduce the new, expanded Freedom range. With four models to choose from, the 2007 Freedom range features brand new options normally found on more expensive car navigators.

Freedom Range Models

Key Features

n n n n n

Easy to use entry level navigation device Pre-installed safety camera data* Real-time trafc information 3.5 colour touch screen Nearest Parking and Petrol buttons Full 8-digit postcode search (UK only) Pause route option Latest SiRFstarIII GPS receiver technology Slim, portable, high quality design Full 3D moving maps with journey progress bar Maps pre-installed onto internal memory Simple user interface

Key Features as listed

F20 EUROPE

As F20 plus:

New Freedom Range features for 2007
Navmans unique Bluetooth hands-free calling technology can now be used with or without the navigation device. It also features voice recognition and caller ID and can be paired with up to 5 mobile phones. Another rst is Navmans combined Trafc and Bluetooth device, tted in seconds and offering all the benets of hands-free calling technology with subscription-free, real-time trafc information, in one simple to use unit.

n n n n n n n

Pre-installed Western European maps 21 countries Pre-installed safety camera data for 7 European countries**
As F20 plus: Customer Benets
Integrated real-time trafc information subscription-free
Affordable 3D navigation Easily transferable from car to car Turn-by-Turn voice guided navigation with 3D graphics Drive-Away, works straight out of the box Back-on-Track, gets you back to your route if you take a wrong turn No PC connection required

F40 EUROPE

Hands-free
Bluetooth hands-free calling Pre-installed Western European maps - 21 countries
* Optional subscription to the Navman safety camera database service (with optional Connectivity Kit)
** Great Britain, France, Spain, Belgium, Netherlands, Norway & Sweden

www.navman.com

Bluetooth hands-free calling User-friendly software for easy navigation
Nearest Parking & Petrol buttons Real-time trafc information
Full 8 digit postcode search
Pre-installed European maps Pre-loaded UK and Ireland maps

Technical Specications

Hardware
Weight (device only): 200g Size: 79.5mm (H) x 116mm (W) x 24mm (D)
Pre-installed safety camera data 3.5 (8.9 cm) colour screen

3D moving maps

Back-on-Track

Box Contents

F20 & F20 Europe box dimensions: 231mm (H) x 155mm (W) x 128mm (D) F30 & F40 Europe box dimensions: 240mm (H) x 163mm (W) x 178mm (D)

Optional Accessories

Memory: 32MB ash and integrated 256MB, 512MB or 2GB depending on region SD/MMC memory expansion Processor: Intel 200MHz XScale Rechargeable integrated battery: Li-ION up to 3.5 hrs life (depending on usage) High quality loud speaker GPS Receiver: SiRFstarIII Screen: Anti-glare high resolution 3.5 (8.9 cm) colour touch screen In-car windscreen mount Power: 12V in-car power charger T1 Trafc Pack (F30 only) B2 Hands-free (F40 Europe only)

n n n n

F30 Trafc
Contents as per F20 plus: n T1 Trafc Pack Part number F30: AA008221 EAN: 9419777108634
Mini MCX external GPS antenna AC adaptor 12V in-car charger
NAVMAN Navigation device In-car windscreen mount 12V in-car power charger Documentation pack (user manual, in-car installation guide, warranty document, GPS FAQ guide, help and support sheet)
F40 Europe & Hands-free
Contents as per F20 plus: n B2 Hands-free n Western European maps pre-loaded Part number F40 Europe: AA008210 EAN: 9419777104094
Carry case In-car windscreen mount SD cards containing additional maps
Part number F20: AA005808-6E2 EAN: 9419777105879

F20 Europe

Contents as per F20 plus: n Western European maps pre-loaded Part number F20 Europe: AA005986-6E2 EAN: 9419777108528

Mapping

Tele Atlas map data Regional maps pre-installed onto internal memory Street level Western European maps pre-installed onto internal memory for drive-away performance (F20 Europe & F40 Europe)

Navigation Views

T1 Trafc Pack
B2 Handsfree / B2+ Handsfree & Trafc

Connectivity Kit

Turn-by-Turn Route summary 3D moving map 2D mini map
Bluetooth Hands-free Technology

Software Features

n n n n n n n n n
Advanced Echo Cancellation Enhanced Noise and Residual Echo Suppressor Built-in voice recognition Pairs with up to 5 phones Compatible with all Bluetooth mobile phones: Blackberry, HP, i-mate, Motorola, NEC, Nokia, Qtek, Palm, Panasonic, Philips, Sagem, Samsung, Sendo, Sharp, Siemens, Sony-Ericsson, SPV, Telital
Pre-installed safety camera data Drive-Away Back-on-Track (gets you back to your route if you take a wrong turn) POI (Places of Interest) Full 8 digit postcode address search facility (UK only) Voice guided instructions Favourite destinations stored for easy address look-up Multiple routing options e.g. shortest/fastest route, nearest POI Live trafc updates through T1 Trafc Pack and B2+, also available as an option (sold separately) Manage, save or delete favourite and recent destinations
Navman Europe Ltd T +44 (0) 500