Reviews & Opinions
Independent and trusted. Read before buy NEC Multisync LCD 1510!

NEC Multisync LCD 1510

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
NEC Multisync LCD 1510, size: 1.1 MB
Related manuals
NEC Multisync LCD 1510V
NEC Multisync LCD 1510 Setup Instruction

Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

NEC Multisync LCD 1510About NEC Multisync LCD 1510
Here you can find all about NEC Multisync LCD 1510 like manual and other informations. For example: review.

NEC Multisync LCD 1510 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a NEC Multisync LCD 1510 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your NEC Multisync LCD 1510 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 1. Page 1 of 1. Average Rating:
Zartol 10:14pm on Friday, July 30th, 2010 
There are very few options on the market for critical color quality work. This monitor delivers excellent results without killing your bank account. The shipping carton was larger than I expected. The display was placed in the carton fully assembled.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

English

78133551/Fix.PM5

98.3.17, 8:19 AM
Introduction to the NEC MultiSync LCD1510 / LCD1510V / LCD2010
Congratulations on your purchase of the NEC MultiSync LCD1510/ LCD1510V/LCD2010 true colour monitor!
Wide Viewing Angle Technology (MultiSync LCD1510 and MultiSync LCD2010 only)
Allows the user to be able to see the monitor from any angle(160 degrees) from any orientation Portrait or Landscape. Provides full 160 viewing angles either up, down, left or right.

Analog Advantage

Capable of displaying unlimited colours in a continuous spectrum, providing a truer representation of colour. The monitors high contrast LCD enhances colour vibrancy and improves focus with no geometric distortion.

Wider Compatibility

Because the MultiSync LCD monitor is analog through and through, it does not require special analog to digital display or interface cards but can accept RGB input directly.

Reduced Footprint

Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitors small footprint and low weight allow it to be moved or transported easily from one location to another.

Colour Control system

Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards.
OSM (On-Screen Manager) Controls
Allow you to quickly and easily adjust all elements of your screen image via simple to use on-sreen menus.

ErgoDesign Features

Enhance human ergonomics to improve the working environment, protect the health of the user and save money. Examples include OSM controls for quick and easy image adjustments, tilt/swivel pivot stand for preferred angle of viewing, small footprint and compliance with MPRII and TCO guidelines for lower emissions.

Pivoting Stand

Allows users to adjust the monitor to the orientation that best fits their application, either Landscape orientation for wide documents, or portrait orientation for the ability to preview a full page on one screen at one time. The Portrait orientation is also perfect for full screen video conferencing.
Plug and Play (MultiSync LCD1510 and MultiSync LCD1510V only)
The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display performance.
IPM (Intelligent PowerManager) System
Provides innovative power-saving methodes that allow the monitor to shift to a lower power consumption level when on but not in use, saving two-thirds of your monitor energy cost, reducing emissions and lowering the air conditioning cost of the workplace.
Multiple frequency Technology
Automatically adjusts monitor to the display cards scanning frequency, thus displaying the resolution required.

FullScan Capability

Allows you to use the entire screen area in most resolutions, significantly expanding image size.

VESA Standard Mounting Interface
Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.

Contents of Package

Your new MultiSync LCD monitor box should contain the following:
MultiSync LCD1510 / LCD1510V monitor with Video Signal Cable and AC Adapter
MultiSync LCD2010 monitor with 15-pin VGA to BNC Cable and AC Adapter
NEC MultiSync LCD1510 (Model LA-152lJMW)/ NEC MultiSync LCD1510V (Model LA-1522JMW). NEC MultiSync LCD2010 (Model LA-2032JMW). AC power cable. AC Adapter Video Signal Cable 15 pin VGA to 15 pin mini D-SUB (LCD1510 / LCD1510V). Video Signal Cable 15 pin VGA to BNC (LCD2010). Users manual.
Remember to save the original box and packing materials to transport or ship the monitor.

Recommended Use

For optimum performance, please note the following when setting up and using the MultiSync LCD1510 / LCD1510V / LCD2010 colour monitor:
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. The optimum monitor position is facing away from direct sunlight. Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor. Do not spill any liquids into the cabinet or use your monitor near water. Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or fatal or may cause electric shock, fire or equipment failure. Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire. Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to the monitor. Use the monitor in a clean and dry area. Handle with care when transporting. Save packaging for transporting. The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet which is easily accessible.

Use supplied AC Adapter. The inside of the fluorescent tube located within the LCD monitor contains mercury. Please follow the bylaws or rules of your local municipality to dispose of this tube property. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution, glass cleaner or tissue paper. For optimum performance, allow 20 minutes for warm-up. Avoid displaying fixed patterns on the monitor for long periods of the time to avoid image persistence (after-image effects.) Avoid applying pressure to the LCD monitor surface.
Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:
When the power supply cord or plug is damaged. If liquid has been spilled or objects have fallen into the monitor. If the monitor has been exposed to rain or water. If the monitor has been dropped or the cabinet is damaged. If the monitor does not operate normally by following operating instructions.
CORRECT PLACMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR:
Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance of MultiSync LCD1510 / LCD1510V is 53 cm, MultiSync LCD2010 is 61 cm. Rest your eyes periodically by focusing on an object at least 6 m away. Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen. If reflected light makes it hard for you to see your screen, use an anti-glare filter. Adjust the monitors brightness and contrast control to enhance readability. Use a document holder placed close to the screen. Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize turning your head while you are typing. Get regular eye checkups.

Installation

Connection to your Personal Computer
The MultiSync LCD1510 / LCD1510V / LCD2010 true colour monitor complements PC compatible computers. Your system has one of two configurations: the video controller is built into the computer. the video controller is in the form of a display card (sometimes referred to as graphics card, video adapter or graphics board).
Both configurations have a video connector (or a CRT PORT on laptop computers). If you are not sure which connector is the video connector, refer to your computer or display card manual. To attach the monitor to your system, follow these instructions: 1. Turn off the power to the monitor and computer. 2. If necessary, install the display card. For more information about installing your card, refer to the display card manual. 3. Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your computer. Tighten all screws (Figure A.1). 4. For the MultiSync LCD1510, MultiSync LCD1510V: Connect the 15-pin mini D-SUB of the video signal cable and the AC Adapter cable to the appropriate connectors on the back of the monitor (Figure C.1). For the MultiSync LCD2010: Remove connector cover on back of monitor. Connect the BNC cables and AC adapter cable to the appropriate connectors on the back of the monitor. Connect the red BNC cable to the BNC connector on the monitor labeled R, the green BNC cable to the BNC connector labeled G/Sync, the blue BNC cable to the BNC connector labeled B. If you have a fourth BNC connector (Composite Sync), connect it to the BNC connector on the monitor labeled H/CS. If you have a fifth BNC connector (Vertical Sync), connect it to the BNC

98.3.17, 8:20 AM

connector on the monitor labeled VS (Figure D.1). Place the 15-pin VGA to BNC cable and the AC adapter cable under Clip A (Figure D.1A). Then place the 15-pin VGA to BNC cable and the AC adapter cable under Clip B (Figure D.1B). Replace connector cover. Note: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module and/or shorten the modules life. 5. Connect one end of the power cord to the AC Adapter and the other end to the power outlet (Figure E.1). 6. Turn on the monitor (Figure F.1) and the computer. 7. To complete the setup of your MultiSync LCD monitor, use the following OSM controls: Auto Adjust Contrast Auto Adjust Image Adjust Fine (MultiSync LCD2010 monitor only)
NOTE: Manual adjustment of the H/V Position and Image Adjust H Size / Fine controls may be required to complete setup of your MultiSync monitor. For a full description of these OSM controls, refer to the Controls section of this Users Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this Users Manual.

E - 10

Mac Adapter (not included) 15-pin mini D-SUB

Figure A.1

Figure B.1 Connector Cover MultiSync LCD1510 monitor
MultiSync LCD2010 monitor

Figure C.1

Power Cord Figure E.1
Figure F.1 Figure D.1A Figure D.1B Figure D.1

Power Switch

E - 11
Connection to your Personal Computer (Macintosh)
With the Macintosh cable adapter, the MultiSync LCD1510 / LCD1510V / LCD2010 colour monitor is compatible with the Macintosh family of computers. You will connect your MultiSync colour monitor one of two ways to your Macintosh computer: On-board video port1 NuBus/PCI/PDS display card
Both configurations should have the same style video connector. If you are not sure which port is the monitor connector, please reference your computer or display card manual. To attach your MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your MultiSync LCD monitor and Macintosh. 2. If neccssary, install the display card. For more information on this installation, reference the display card manual. 3. Connect the MultiSync LCD1510, MultiSync LCD1510V or MultiSync LCD2010 Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync LCD1510, MultiSync LCD1510V or MultiSync LCD2010 Macintosh cable adapter (Figure B.1). Tighten all screws. 4. For the MultiSync LCD1510, MultiSync LCD1510V: Connect the 15-pin mini D-SUB of the video signal cable and the AC Adapter cable to the appropriate connectors on the back of the monitor (Figure C.1). For the MultiSync LCD2010: Remove connector cover on back of monitor. Connect the BNC cables and AC adapter cable to the appropriate connectors on the back of the monitor. Connect the red BNC cable to the BNC connector on the monitor labeled R, the green BNC cable to the BNC connector labeled G/Sync, the blue BNC cable to the BNC connector labeled B. If you have a fourth BNC connector (Composite Sync), connect it to

E - 12

the BNC connector on the monitor labeled H/CS. If you have a fifth BNC connector (Vertical Sync), connect it to the BNC connector on the monitor labeled VS (Figure D.1). Place the 15-pin VGA to BNC and AC adapter cable under Clip A(Figure D.1A). Then place the 15-pin VGA to BNC and AC adapter cable under Clip B(Figure D.1B). Replace connector cover. NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module and/or shorten the modules life. 5. Connect one end of the power cord to the AC Adapter and the other end to the power outlet (Figure E.1). 6. Turn on the monitor (Figure F.1) and the computer. 7. To complete the setup of your MultiSync LCD monitor, use the following OSM controls: Auto Adjust Contrast Auto Adjust Image Adjust Fine (MultiSync LCD2010 monitor only)
NOTE: Manual adjustment of the H/V Position and Image Adjust H. Size / Fine controls may be required to complete setup of your MultiSync monitor. For a full description of these OSM controls, refer to the Controls section of this Users Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this Users Manual. Please contact your local dealer for information about the Mac Adapter.

E - 13

Shipping Screws
Loosen the two shipping screws (Figure SS.1). (The screws will not come out. Turn them until they are loosened completely.) If the screws are loosened correctly only the screen will rise up when lifting the cabinet. (Refer to figure RL.1). If the unit needs to be repackaged for shipping, make sure monitor is in lowest Landscape position, then retighten the shipping screws in order to protect the internal parts.

Cable Management

To use the cable management feature, lift up then remove back cover (Figure CM.1). Place all cables into the vertical groove, leaving 15cm to 25cm of slack in the cables to allow the monitor to rotate between Landscape and Portrait orientation (Figure CM.2). To replace back cover, push in then slide down (Figure CM.3).
Raise and Lower Monitor Screen
The monitor may be raised or lowered in either Portrait or Landscape mode. To raise screen, place hands on each side of the monitor and lift to the desired height (Figure RL.1). To lower screen, place one hand under bottom of screen, lift slightly (Figure RL.2) and simultaneously push the button on the bottom back of the stand (Figure RL.3). Screen will lower while button is pushed in. Release button to lock screen in place. CAUTION: Although the monitor has been designed not to lower automatically when the button is pushed, ALWAYS support the bottom of the screen with one hand.

E - 14

Screen Rotation
Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching your fingers. To raise the screen, place hands on each side of the monitor and lift up (Figure R.1). To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter-clockwise from Portrait to Landscape (Figure R.2). To toggle the orientation of the OSM menu between Landscape and Portrait modes, press the RESET button while OSM menu is off.

Tilt and Swivel

Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).

E - 15

Phillips head screwdriver

Figure SS.1

Cable Cover Lift up then remove back cover Leave sufficient length of cable

Figure CM.1

Figure CM.2 Push in and slide down Figure CM.3

Figure RL.1

E - 16

Figure RL.2

Figure RL.3

Figure R.1

Figure R.2

Figure TS.1

E - 17
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place hands on each side of the monitor screen and raise it to the maximun height (Figure R.1). 3. Place monitor face down on a non-abrasive surface (Place the screen on a 40mm platform so that the stand is parallel with the surface.) (Figure S.1).

Figure S.1

4. Remove cable cover. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure S.2). The monitor is now ready for mounting in an alternate manner. 5. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method.

Figure S.2

E - 18

Controls

OSM Controls
The OSM controls on the front of the monitor provide the following functions:
To access OSM press any of the control buttons ( , , , ) or the PROCEED or EXIT button. To rotate OSM between Landscape and Portrait modes, press the RESET button. Main Menu Exits the OSM controls. / Moves the highlighted area up/down to select one of the controls Moves the highlighted area left / rights to select control menus. Has no function. Resets the highlighted contol menu to the factory setting. Sub-Menu Exits to the OSM main menu. Moves the highlighted area up/down to select one of the controls Moves the bar left / right to increase or decrease the adjustment. Activates Auto Adjust and ALL RESET functions. Resets the highlighted contol to the factory setting.

EXIT CONTROL

CONTROL

PROCEED RESET

NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the RESET function by pressing the EXIT button.

E - 19

Brightness/Contrast Controls
BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO ADJUST CONTRAST Adjusts the image displayed for non-standard video inputs.

Auto Adjust

MultiSync LCD1510, LCD1510V monitor only Automatically adjusts the Image Position, the H. Size or Fine settings. MultiSync LCD2010 monitor only Automatically adjusts the Image Position or the H. Size setting. NOTE: Manual adjustment of the H/V Position and Image Adjust H. Size / Fine controls may be required to complete setup of your MultiSync monitor.

Position Controls

H. POSITION Controls Horizontal Image Position within the display area of the LCD. V. POSITION Controls Vertical Image Position within the display area of the LCD. AUTO Automatically sets the Horizontal and Vertical Image Position within the display area of the LCD.

98.3.17, 8:21 AM

E - 20

Image Adjust Controls

H. SIZE Adjusts the horizontal size by increasing or decreasing the this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. NOTE: The Image Adjust Fine control must be used to complete the setup of your MultiSync LCD2010 monitor. MultiSync LCD1510, MultiSync LCD1510V monitor only Automatically adjusts the H. Size or Fine settings. MultiSync LCD2010 monitor only Automatically adjusts the H. Size settings.

Colour Control System

Five colour presets select the desired colour setting. Each colour setting is adjusted at the factory. R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or decrease) will be shown by the bars.
OSM H. POS. OSM V. POS. You can choose where you would like the OSM control window to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left, right, up or down. ALL RESET Selecting ALL RESET allows you to reset all OSM control settings back to the factory settings. Individual settings can be reset by highlighting the control to be used and pressing the RESET button.

E - 21

Information
Indicates the current display resolution, frequency setting and type of Sync signal of the monitor. NOTE: Mode Change should only be used if a resolution is not recognized by the monitor. The user can change to the appropriate resolution by selecting the Mode information and selecting (increase or decrease) the corresponding option. NOTE: If the or button is pressed while TYPE is highlighted, then Sync Type is switched between Separate Sync and Sync On Green. OSM LOCK OUT The OSM LOCK OUT control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the LOCK OUT mode, a screen will appear indicating that OSM controls are locked out. To enter the LOCK OUT mode, simultaneously press the PROCEED and button. The LOCK OUT window will appear. To activate the LOCK OUT function, simultaneously press and hold down the PROCEED and button. The OSM window will disappear within seconds and the LOCK OUT function will be activated. To deactivate the LOCK OUT mode, simultaneously press the PROCEED and button.

E - 22

Specifications
MultiSync LCD1510 / LCD1510V
Display 1510: 38 cm (15 inch) viewable image size; 1024 x 768 native resolution (Pixel Count); active matrix; thin film transistor (TFT); liquid crystal display (LCD); 0.297 mm dot pitch; 180 cd/m2 white luminance, typical; 100:1 contrast ratio, typical 1510V: 38 cm (15 inch) viewable image size; 1024 x 768 native resolution (Pixel Count); active matrix; thin film transistor (TFT); liquid crystal display (LCD); 0.297 mm dot pitch; 200 cd/m2 white luminance, typical; 200:1 contrast ratio, typical Video Sync Analog 0.7 Vp-p 75 Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Negative) (TTL Level) Sync on Green video (Positive) 0.7 Vp-p and sync. Negative 0.3 Vp-p Unlimited number of colours (Depends on the graphics board) 24.8 kHz to 60.0 kHz (Automatically) 56.2 Hz to 85.1 Hz (Automatically) 720 x 400: VGA text* 640 x 480 at 60 Hz to 85 Hz* 800 x 600 at 56 Hz to 85 Hz* 832 x 624 at 75 Hz* 1024 x 768 at 60 Hz to 75 Hz** 480 x 600 at 60 Hz to 85 Hz* 600 x 800 at 56 Hz to 85 Hz* 624 x 832 at 75 Hz* 768 x 1024 at 60 Hz to 75 Hz**

Input Signal

Display Colours Synchronisation Range Resolutions Supported
Analog Input: Horizontal Vertical Landscape

Portrait

E - 23

Active Display Area***

Landscape Portrait
Horizontal Vertical Horizontal Vertical
304 mm 228 mm 228 mm 304 mm
Power supply Current Rating Dimensions LCD1510 LCD1510V Landscape Portrait Hight Adjust LCD1510 LCD1510V Temperature Humidity Temperature Humidity
AC 100-120 V / 220-240 V 50/60 Hz 0.7 A @ 100-120 V / 0.4 A @ 220-240 V 0.5 A @ 100-120 V / 0.3 A @ 220-240 V 381mm(W) x 392mm(H) x 217mm(D) 312mm(W) x 427mm(H) x 217mm(D) 55mm 7.0 kg 6.7 kg 5 C to + 35 C 30% to 80% -10 C to + 60 C 10% to 85%
Weight Operating Environmental Considerations Storage Environmental Considerations
* Interpolated Resolutions: when resolutions are shown that are lower than the pixel count of the LCD module, text may appear choppy or lines may appear to be bold. This is normal and necessary for all current flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done. When the interpolated resolutions is not an exact multiple of the native resolution, the mathematical interpolation necessary may cause some lines to appear thicker than others. ** NEC cites recommended resolutions at 75 Hz for optimal display performance. *** Active display area is dependent upon the signal timing.
Technical specifications are subject to change without notice.

E - 24

Multisync LCD2010
Display 51.1 cm (20.1 inch) viewable image size; 1280 x 1024 native resolution (Pixel Count); active matrix; thin film transistor (TFT); liquid crystal display (LCD); 0.31 mm dot pitch; 150 cd/m2 white luminance, typical; 150:1 contrast ratio, typical Video Sync Analog 0.7 Vp-p 75 Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Negative) (TTL Level) Sync on Green video (Positive) 0.7 Vp-p and sync. Negative 0.3 Vp-p Unlimited number of colours (Depends on the graphics board) 24.0 kHz to 80.0 kHz (Automatically) 56.0 Hz to 76.0 Hz (Automatically) 720 x 400: VGA text* 640 x 480 at 60 Hz to 76 Hz 800 x 600 at 56 Hz to 76 Hz* 832 x 624 at 75 Hz* 1024 x 768 at 60 Hz to 76 Hz* 1280 x 960 at 60 Hz to 76 Hz 1280 x 1024 at 60 Hz to 76 Hz** 480 x 640: at 60Hz to 76Hz 600x 800 at 56 Hz to 76 Hz* 624 x 832 at 75 Hz* 768 x 1024 at 60 Hz to 76 Hz* 960 x 1280 at 60 Hz to 76 Hz* 1024 x 1280 at 60 Hz to 76 Hz** Horizontal Vertical Horizontal Vertical 399 mm 319 mm 319 mm 399 mm

E - 25

Power supply Current Rating Dimensions Landscape Portrait Hight Adjust
AC 100-120 V / 220-240 V @ 50/60 Hz 1.0A @ 100-120V / 0.5A @ 220-240V 498(W) x 501(H) x 262(D) mm 418(W) x 541(H) x 262(D) mm 80mm 12.5kg Temperature Humidity Temperature Humidity 5 C to + 30 C 30% to 80% -10 C to + 60 C 10% to 85%
* Interpolated Resolutions: when resolutions are shown that are lower than the pixel count of the LCD module, text may appear choppy or lines may appear to be bold. This is normal and necessary for all current flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done. When the interpolated resolutions is not an exact multiple of the native resolution, the mathematical interpolation necessary may cause some lines to appear thicker than others. ** NEC cites recommended resolutions at 60 Hz for optimal display performance. *** Active display area is dependent upon the signal timing.

E - 26

Troubleshooting/Support
Problem No picture Check These Items - The signal cable should be completely connected to the display card/computer. - The display card should be completely seated in its slot. - Power button and computer power switch should be in the ON position. - Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) - Check the monitor and your display card with respect to compatibility and recommended settings. - Check the signal cable connector for bent or pushedin pins. Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor, or simultaneously press the RESET and Power buttons. Image persistence is when a ghost of an image remains on the screen even after the monitor has been turned off. Unlike CRT monitors, LCD monitors image persistence is not permanent. To alleviate image persistence, turn the monitor off for as long as an image was displayed. If an image was on the monitor for one hour and a ghost of that image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC recommends using a screen saver at regular intervals whenever the screen is idle.
Power Button does not respond Image persistence

E - 27

Problem Image is unstable, unfocused or swimming is apparent
Cheak These Items - Signal cable should be completely attached to the computer. - Use the OSM Image Adjust controls to focus and adjust display by increasing or decreasing the Fine Control. When the display mode is changed, the OSM Image Adjust settings may need to be re-adjusted. - Check the monitor and your display card with respect to compatibility and recommended signal timings. - If your text is garbled, change the video mode to non -interlace and use 60Hz refresh rate. - Power Switch should be in the ON position and power cord should be connected. - Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). and

LED on monitor is not lit (no green or amber colour can be seen)
Display image has a Select TYPE in the OSM Information menu green cast to it press the or Control button.
Display image is not - Use the OSM Image Adjust controls to increase or sized properly decrease the H. Size. - Check to make sure that a supported mode and signal timing has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode or refresh rate.) Selected resolution is not displayed properly Select the Display Resolution in the OSM Information menu confirm that the appropriate resolution has been selected. If not, select corresponding option. by pressing the or Control button.

98.3.17, 8:22 AM

 

Tags

KDE-P37hv2 KG200 IDF-1020 Leica Iiic CMT-VP11 DLE5955S DFS-700P 30169 CDR632 L1920P W610I Review Rcr-1 MX-880 RT-29FA33RQ Grandam 1995 Rumble 25 Advantage55 Charger LN-T1954H XD-J220 M310- Receiver Videolink SC101 PT-2300 RE-29FA33X Nemo Wide 2243LNX SLV-N50 WD-80150TUP PDX-1 1000 Butler 2405 DVD4730 HW-C770S Powerlite 62C Palmtop PC ER-A430 MSC 3DX Active S9 W8400 42LB7DF EL-2192RII I XL Fryer TA-FE510R 360 M1 K 702 SA-HT400 Nokia N81 MHC-GR7 IC-M84 Explorer 220 84 T Smartfinder Lens E 1312 Research A-06 Continental 2001 8 5 DWC513BLS DXZ755MC LC-SM3 HT-KP30 Reader L1800P-lb886f-ul- DVD-HR738 AP 2300 47LG7000 VDR-D200 BH-604 TL110 KLV-20SP2 SDV2740 S Usaf Joybook 8000 LN37B530 Fb915BP Photosmart 370 DCP-117C 2159M Photosmart 420 CFD-V30 V3000Z 4 0 Panasonic A101 DSC-W30 5014984 H3100 HX6932 Lexmark E240 Hermes RD-XS24SF VSX-1019AH-K 127 X Ddlt21 KX-FP205 DWA-150R KX-TH111 Service RY41002 Frame

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101