Remote Cord

De Fr Es Se Ru Nl Pt It Ck

Instruction Manual

TIMER ACTIVE SET RELEASE

RELEASE

TIMER ACTIVE
TIMER ACTIVE RELEASE SET

TIMER ACTIVE

SET RELEASE TIMER ACTIVE HOLD

TIMER ACTIVE RELEASE

M Bulb M S AF-C

SET DELAY LONG INTVL N

ACTIVE TIMER

Table of Contents

For Your Safety..3 Notices...4 En Introduction...5 Parts of the MC-36..5 Body...5 Control Panel...6 Inserting Batteries..6 Replacing Batteries..6 When the MC-36 Is Not in Use..6 The Illuminator/Lock Button..7 Connecting the MC-36..7 Using the MC-36...8 Timed Photography..8 Manual Release... 15 Precautions for Use... 16 Caring for the MC-36.. 16 Specifications.. 17 1

MC-36 Remote Cord

For Your Safety (1/2)
To prevent damage to your Nikon product or injury to yourself or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use this equipment will read them. The consequences that could result from failure to observe the precautions listed in this section are indicated by the following symbol:
This icon marks warnings, information that should be read before using this Nikon product to prevent possible injury. Do not disassemble or modify Failure to observe this precaution could result in electric shock or product malfunction. Should the product break open as the result of a fall or other accident, remove the batteries and take the product to a Nikon-authorized service representative for inspection. Keep dry Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this precaution could result in re or electric shock. Do not use in the presence of flammable gas Failure to observe this precaution could result in explosion or re. Keep out of reach of children This device contains small parts which may pose a choking hazard. Consult a physician immediately if a child swallows any part of this device. Turn off immediately in the event of malfunction Should you notice smoke or an unusual smell coming from this device, remove the battery immediately and take the device to a Nikon-authorized service representative for inspection, taking care to avoid burns. Continued operation could En result in injury. Do not expose to high temperatures Do not leave the device in a closed vehicle under the sun or in other areas subject to extremely high temperatures. Failure to observe this precaution could result in re or in damage to the casing or internal parts. Observe precaution when handling batteries Batteries may leak or explode if improperly handled. Observe the following precautions when handling batteries for use in this device: Use only batteries listed in this manual. Do not mix old and new batteries or batteries of dierent types.

For Your Safety (2/2)

En Do not short or disassemble.
Read and follow all warnings and instructions provided by the manufacturer. Do not expose to ame or excessive heat. Do not attempt to insert batteries upside down or backwards. Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove the batteries when leaving the product unattended for prolonged periods or when no charge remains. Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.

Notices (1/2)

Notice for Customers in the U.S.A.: Federal Communications Commission (FCC) Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help. CAUTIONS Modifications: The FCC requires the user to be notied that any changes or modications made to this device that are not expressly approved by Nikon Corporation may void the users authority to operate the equipment. Interface Cables: Use the interface cables sold or provided by Nikon for your equipment. Using other interface cables may exceed the limits of Class B Part 15 of the FCC rules.

Notices (2/2)

Notice for Customers in the State of California WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A. Tel.: 631-547-4200 Notice for Customers in Canada CAUTION: This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. ATTENTION: Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

Introduction

Thank you for your purchase of an MC-36 remote cord. The MC-36 is equipped with an interval timer suited to a wide variety of tasks, including astronomical photography. See page 17 for a list of compatible cameras.

Parts of the MC-36 (1/3)

Refer to the illustrations inside the front cover. Body En 10-pin connector...7 Cord Release lamp... 1213 Control panel.. 6, 7, 813, 15 TIMER START/STOP button.. 1213 SET button..8, 10, 12 Illuminator/lock button..7 Arrow button... 1011 Shutter-release button...15 Battery-chamber cover..6 Eyelet for strap (available separately; use cell phone or other similar strap)

Parts of the MC-36 (2/3)

Control Panel* Selection cursor.. 1011 En Timer display.. 1013, 15 Lock indicator...7 Low battery indicator..6 TIMER ACTIVE indicator. 1213 Speaker on/o indicator..9, 11 SET indicator.. 8, 1012 RELEASE indicator.. 1213, 15 Number of shots.. 913
* The illustration inside the front cover shows the control panel with all elements lit. In the other illustrations throughout this manual, elements relevant to the explanation in the accompanying text are shown in black. Indicators not mentioned in the text are shown in gray.
Inserting Batteries Slide the battery-chamber cover () from the back of the MC-36 and insert two AAA 1.5 V LR03 alkaline batteries (available separately) as shown.
Replacing Batteries When replacing batteries: 1 Check that the TIMER ACTIVE () and RELEASE () indicators are not displayed (see right). 2 Turn the camera o and disconnect the MC-36. 3 Remove the batteries. 4 Wait until the control panel has gone out and insert new batteries. When the MC-36 Is Not in Use The MC-36 is not equipped with an o switch. To reduce the drain on the batteries when the MC-36 is not in use, end shooting and check that the TIMER ACTIVE (), SET (), and RELEASE () indicators are not displayed (see right). The drain on the batteries increases when these indicators are ashing.

The Low Battery Indicator ( ) The low battery indicator () will blink when the batteries are low. Ready spare batteries.

Parts of the MC-36 (3/3)

The TIMER ACTIVE, SET, and RELEASE Indicators

Connecting the MC-36

The Illuminator/Lock Button Press the illuminator/lock button () briey to activate the control panel backlight. The backlight will remain lit for about six seconds; pressing the arrow button () while the backlight is on extends the timer for another six seconds. To lock all controls except the shutter-release () and illuminator/lock buttons, press the illuminator lock button until the lock icon ( ) is displayed in the control panel. To release the lock, press the illuminator/lock button until the lock icon is no longer displayed. 1 Turn the camera o. 2 Check that the TIMER ACTIVE () and REEn LEASE () indicators are not displayed. 3 Remove the 10-pin terminal cover from the camera. Keeping the mark on the 10-pin connector () aligned with the mark on the camera body, insert the connector as shown and then tighten the locking nut.
It means this; do this to turn it off Timer active (page 13); press TIMTIMER ACTIVE ER START/STOP button (). Settings can be modied (page SET 8); press SET button (). RELEASE Manual release active (page 15); (TIMER release shutter-release button ACTIVE not (; if button is in HOLD position, ashing) release shutter-release lock).

If this flashes

Disconnecting the MC-36 After checking that the TIMER ACTIVE () and RELEASE () indicators are not displayed, turn the camera o and disconnect the MC-36. Replace the 10-pin terminal cover.

Using the MC-36

The MC-36 functions as: An automatic timer (pp. 814). Choose the delay (time before shooting starts), exposure time, interval, and number of shots for timed interval photography. Shutter speed can be selected with the camera if desired (pg. 14). A manual release (pg. 15). Take photographs manually using the shutter-release button on the MC-36. Photographs can be taken manually even when the timer is running.

Timed Photography (1/7)

1. Adjust Camera Settings 1.1 Connect the MC-36 (pg. 7) and turn the camera on. 1.2 Adjust camera settings as follows (see the camera manual for details):
M (manual) Bulb O AF-C (continuous-servo autofocus)* or M (manual) Continuous S (single frame) * Select release priority if available. Exposure mode Shutter speed Interval timer Focus mode

2. Set the Timer 2.1 Press the SET button (). SET will ash in the control panel.
The MC-36 can be connected to the camera after the timer has been set.

Timed Photography (2/7)

2.2 Adjust the following settings:
Option DELAY LONG INTVL N Description Delay before shutter is released Exposure time Interval Number of shots Speaker on/o Supported settings 0 s to 99 hrs 59 min 59 s (in one-second increments) 1 s to 99 hrs 59 min 59 s (in one-second increments) 1 to 399, (unlimited) (on), (o )
Number of shots (N) 1st frame 2nd frame nth frame
Delay, Exposure, and Interval Settings
Shutter opens Shutter closes

Exposure time

Interval

Timer starts Timer ends

Timed Photography (3/7)
En Press left or right to select, up or down
to change. The current selection is indicated by the selection cursor (). Adjust settings Setting the Timer Use the arrow button to set the timer. Delay (time until shooting starts) Hour Minute Second Hour
Press SET () at any time to complete the operation and display the new settings for the selected item. To view other settings, press the arrow button left or right. The current selection is indicated by the selection cursor (). Press the SET button to edit the current setting as described above.

Setting complete

Timed Photography (4/7)
Exposure time Minute Second Hour Interval Minute Second Number of shots Speaker

Timed Photography (5/7)

En least one second longer than the exposure time.
When using autofocus, set the delay to two seconds or more and choose an interval at least two seconds longer than the exposure time to ensure that the camera has time to focus. When using long exposure noise reduction (available with some digital cameras), the interval should be at least twice the exposure time. Intervals of 00:00:00 will automatically be reset to 00:00:01 when the SET button () is pressed to put settings into eect. To set the number of shots to (unlimited), select 1 and press the arrow button () down or select 399 and press the arrow button up. Setting the Timer To ensure correct operation, choose an interval at
2.3 After adjusting all settings as desired, press the SET button () to put the new settings into eect. A beep will sound (if the speaker is on) and the SET indicator will go out.
The new settings will remain in eect until changed or until the batteries are removed or exhausted.
3. Start the Timer Press the TIMER START/STOP button (). The timer will start and TIMER ACTIVE () will ash in the control panel. Between shots, the control panel will show the time remaining until the next photograph is taken. If the speaker is on, a beep will sound three times at one-second intervals before the shutter opens. While the shutter is open, the control panel will show the time remaining until the shutter closes, and the release lamp and RELEASE indicator () will ash at one-second intervals. The number of shots remaining will be updated each time a photograph is taken.

Timed Photography (6/7)

Control Panel Display (Timer Active) Between shots: Time remaining until next shot While shutter is open: Time remaining until shutter closes Number of shots remaining Flashes while shutter is open
4. End Shooting Shooting will end automatically when the seEn lected number of shots has been taken. To end shooting before all photographs have been taken, press the TIMER START/STOP button ().
Flashes while timer is active
The Speaker and Release Lamp The following illustration shows when a beep will sound () and the release lamp ash () with a delay of 5 s, an exposure time of 4 s, and an interval of 9 s.
Shutter open Shutter closed

Timer starts

Timed Photography (7/7)
Using the Camera to Select Shutter Speed To take photographs at the shutter speed selected with the camera, adjust settings as follows: Exposure mode M (manual) or S (shutter-priority auto) Shutter speed Any Camera Interval timer O Focus mode AF-C (continuous-servo autofocus)* or M (manual) Shooting mode S (single frame) Exposure time 0 s Interval Longer than camera shutter speed * Select release priority if available. When using autofocus, choose an interval at least two seconds longer than the camera shutter speed to allow the camera time to focus. When using long exposure noise reduction (available with some digital cameras), choose an interval at least double the camera shutter speed. MC-36 Using the Timer Before using the timer for extended periods, check that the batteries have enough charge. Replace the batteries when the low battery indicator ( ) ashes in the control panel ().

Manual Release

The MC-36 shutter-release button () functions in much the same way as the camera shutter-release button. 1. Adjust Camera Settings Connect the MC-36 (pg. 7) and turn the camera on. Choose exposure mode, shutter speed, focus mode, and shooting mode as desired. 2. Take Pictures 2.1 Press the MC-36 shutter-release button () halfway and check focus and exposure, then press it the rest of the way down to take a picture. While the shutter is open, a beep will sound at one-second intervals, the RELEASE indicator () will ash, and the control panel will show the time remaining until the shutter closes. To keep the shutter-release button fully pressed for bulb photography, slide the button to the HOLD position. Slide it in the opposite direction to release the lock.
The MC-36 shutter-release button can be used when no batteries are inserted. The control panEn el will remain o and no beep will sound. The shutter-release button can be used to release the shutter manually while the timer is active. Timer count-down (including the controlpanel display, release lamp, and beep) continues during manual release. If a manual release overlaps with an automatic release, the shutter will remain open until both exposure times have expired.

2.2 Release the button to end shooting.

Precautions for Use

Check the camera battery level and number of exposures remaining before using the MC36 (see the camera manual for details). The timer will continue to operate even when no pictures can be recorded due to low battery, lack or lm or memory, or lack of space in the memory buer (digital cameras only). An AC adapter (available separately) is recommended for longer sessions. Some cameras have an AF activation option that determines whether the camera will focus when the shutter-release button is pressed halfway (see the camera manual for details). Enable shutter-release button AF-activation when using the MC-36. Please note that the timer is less accurate than most watches or household clocks. 16

Caring for the MC-36

Do not drop: The product may malfunction if subjected to strong shocks or vibration. Keep dry: This product is not waterproof and may malfunction if immersed in water or exposed to high levels of humidity. Rusting of the internal mechanism can cause irreparable damage. Avoid sudden changes in temperature: Sudden changes in temperature, such as occur when entering or leaving a heated building on a cold day, can cause condensation inside the device. To prevent condensation, place the device in a carrying case or a plastic bag before exposing it to sudden changes in temperature. Keep away from strong magnetic fields: Strong static charges or the electromagnetic elds produced by equipment such as radio transmitters could inter fere with the device. A note on electronically-controlled devices: In extremely rare instances, unusual characters may appear in the control panel and the device may stop functioning. In most cases, this phenomenon is caused by a strong external static charge. Turn the camera o, disconnect the MC-36, remove the batteries, and then replace them once the control panel has turned o. Caution is required when handling the batteries, which may be hot from use. In the event of continued malfunction, contact your retailer or Nikon representative. The control panel: LCD displays tend to darken at high temperatures and exhibit slower response times at low temperatures. This does not indicate a malfunction.

Specifications

Nikon D2-series, D1-series, D200, and D100 (requires MB-D100 battery pack) digital cameras; Nikon F6, F5, F100, F90X, Fs to 99 hrs 59 min 59 s in one-second increments En 0 s to 99 hrs 59 min 59 s in one-second increments 1 s to 99 hrs 59 min 59 s in one-second increments 1 to 399, (unlimited) Two AAA 1.5 V LR03 alkaline batteries Approximately two months of continuous shooting with a delay of 5 min, an exposure time of 4 min 56 s, and an interval of 5 min. Use of the illuminator will reduce battery life. Operating temperature 20 +50 C (4 +122 F) Dimensions Approximately 18 mm (6.1 1.6 0.7 in.), excluding projections Weight Approximately 105 g (3.7 oz), excluding ferrite core Length of cord Approximately 850 mm (33.5 in.) MC-21 extension cord (operation is not guaranteed if two or more MC-21 extension cords are used), MC-35 GPS adapter cord Compatible remote terminal accessories (available separately) (connects to 10-pin terminal on MC-35) * An MC-26 adapter cord can be used to connect the MC-36 to any camera or accessory with a remote terminal, including motor drives (MD-12 motor drive excluded). Supported cameras* Timer delay Exposure time Interval Number of shots Power source Battery life

Inhalt

Sicherheitshinweise..3 Einfhrung...5 Komponenten des MC-36..5 Gehuse...5 De Display..6 Einsetzen der Batterien..6 Austauschen de Batterien..6 Nichtgebrauch des MC-36..6 Beleuchtung/Arretierung..7 Anschluss des MC-36...7 Verwendung des MC-36..8 Aufnahmen mit Timer..8 Manuelles Auslsen.. 15 Gebrauchshinweise... 16 Pflege des MC-36.. 16 Technische Daten.. 17 1

Kabelfernauslser MC-36

Bedienungsanleitung
Sicherheitshinweise (1/2)
Bitte lesen Sie diese Sicherheitshinweise aufmerksam durch, bevor Sie Ihr Nikon-Produkt in Betrieb nehmen, um Schden am Produkt zu vermeiden und mglichen Verletzungen vorzubeugen. Halten Sie diese Sicherheitshinweise fr alle Personen gribereit, die dieses Produkt benutzen werden. Die in diesem Abschnitt beschriebenen Warnhinweise und Vorsichtsmanahmen sind durch das folgende Symbol gekennzeichnet:

MB-D100

F100 F90X

MC-35 GPS MD-12

... 3... 5 MC-36.. 5... 5... 6... 6... 6 MC-36... 6.. 7 MC-36.. 7 MC-36.. 8... 8...15..16 MC-36..16...17 Ch 1
10...7 .. 1213 ... 6, 7, 813, 15 TIMER START/STOP... 1213 SET...8, 10, 12 ..7 ... 1011 ...15 ...6

MC-36 AAA 1.5 V LR03

... 1011.. 1013, 15...7..6 TIMER ACTIVE 1213..9, 11 SET. 8, 1012 RELEASE. 1213, 15... 913

MC-36 MC-36

13 TIMER START/STOP 8 SET 15 HOLD
MC-TIMER ACTIVE RELEASE MC-36

MC-1. 1.1 1.2

MC-2. 2.1 SET SET

AF-C M S *

SET 00:00:00 00:00:01 1

MC-36 1. MC-36

2. 2.1

2.2 15

... 2 .. 4 .. 5 ... 5 .. 6 ON/OFF .. 6 /LOCK .. 7 .. 7 MC-36 .. 8 .. 8 .. 15 .. 16 .. 16 .. 17

MC-36

(1/3)
. . . . .
( ) . ( ) . ( ) . ( ) . ( ) . ( ) .

.

. . .

. .

. , , .

(2/3)

, , , . . , .

.

.

, .

, .
, , . , , . , , , . , , , .

, .

(3/3)
, , . , , . . . + - , , . , , .
, . , . , , . . , .
MC-36 ( [MC-36] ) . . P.17 .

, , . . .

(1/3)

( )

() ,1.5 V LR03 AAA 2 ( ) .
10 .. P.7 ...P.13 ..P.6, 913, 15 ..P.13 .. P.912 /LOCK .. P.7 .. P.1011 ..P.15 ..P.5, 6 ( )
.. P.1011..P.1013, 15 LOCK . P.7 .. P.5 .P.13 .. P.9, 11 .P.911 . P.13, 15 .. P.913

, .

() . .

(2/3)

. 1. T I M E R ACTIVE () RELEASE() ( ) 2. OFF MC-36 3. 4. ,

ON/OFF

. , . TIMER ACTIVE(),SET(), RELEASE() ( ). .
TIMER ACTIVE, SET, RELEASE
(P.13) () (P.9) SET () (P.15) RELEASE () ( (TIMER ACTIVE HOLD HOLD ) ) TIMER ACTIVE

(3/3)

/LOCK
/LOCK () 6 . () 6 . /LOCK 3 () () /LOCK LOCK . LOCK /LOCK 2 .
1. OFF 2. MC-36 TIMER ACTIVE() RELEASE() (P.6 ) 3. 10 MC- ()

, .

MC-36
TIMER ACTIVE() RELEASE () (P.6 ), OFF MC-36 . 10 .

LOCK

MC- . (P.8) , , , . (P.14). (P.15) MC-36 . .

(1/7)

a. MC-36 (P.7), ON b.
. M ( ) Bulb ( ) M ( ) AF-C ( AF ) S (1 )

AF-C .

(2/7)

a. ()

SET() .
. DELAY ( ) LONG N ( ) ( ) ( ) INTVL ( ) (1 ) (1 ) , ( ON ( ) OFF ( ) )

ON 1 OFF 2 N

MC-36 , MC-36 .

(3/7)

() . : : ( .) () . () (P.12) . . .

(4/7)

(5/7)
1 . AF( ) 2 2 . (D2X NR) ON MC-36 2 . 0 . 0 1 . 1 () , 399 . .

c. ()

( ON ) .

, ( ) .

(6/7)
TIMER ACTIVE () . . 3 1 ( ON ). . 1 () RELEASE () . 1 .

: :

( 5 , 4 , 9 . , )

ON OFF

(7/7)

. () .

. MC-36 . MC-36 M ( ) S ( ) M ( ) AF-C ( AF ) 1 S (1 ) 0 2

MC-36 . () .

1 AF-C . 2 AF 2 . (D2X NR) ON 2 .

MC-36 () / .

a. MC-36 ()
1 RELEASE . () () . HOLD (bulb) . .

MC-36 (P.7), ON

, , , .
MC-36 . , , . . , ( , ). . .
( ) MC-36 . ( 0 ) . AF AF ( AF ). . . . AC ( ). .

(1/2)

. . . . ( ) . . TV . . OFF MC-36 MC-36 . , . .

(2/2)

, . . , TV (VCCI) B . ,TV .
D2 /D1 /D200/D100 ( MB-D100 ) F6/F5/F100/F90X/F 1 , 1.5 V LR03 AAA ( 5 , , 5 ); . - 1554018 mm ( ) 105 g ( ) 850 mm
MC-21 (MC- ) GPS MC-35 (MC- ) ( ) MC-26 . , MD-12 .
Printed in Japan SB6A01000201(D3) 8MRG01D3--