Set the flash mode selector on the SB-22s to TTL.

Foreword

Congratulations. You are now the proud owner of the Nikon Autofocus Speedlight SB-22s, a flash unit offering compact design and easy operation. With a powerful flash output (GN 28 at ISO 100, m), the SB-22s can be used not only for shooting in dimly lit interiors or outside at night, but for daylight fill-in flash. The SB-22s features three flash modes: TTL Auto, Non-TTL Auto, and Manual. In the Non-TTL Auto mode, you have a choice of four shooting apertures at A1, A2, A3 and A4. Other advanced flash capabilities include Bounce, Close-up, and Multiple Flash. To get the most out of your new flash unit, please read this manual before use. Make some test shots Before taking important flash photographs, make some test shots to ascertain the SB-22s is working properly. Use only Nikon-approved equipment The SB-22s is designed for use with Nikon cameras, lenses, and accessories. Using cameras or accessories other than those specified by Nikon may damage the SB-22s. Nikon cannot be held responsible for malfunctions caused by using the SB-22s in ways not specified in this manual, or using the SB-22s with a camera made by another manufacturer.

CAUTION

When replacing batteries, replace all four batteries at the same time, do not mix battery types or brands, do not use old with new batteries, and never reverse the polarity of the batteries when installing. Otherwise, the batteries may catch on fire or explode, due to the possible leakage of corrosive liquids. In the event that corrosive liquids do seep from the batteries, avoid touching the liquids. Certain types of batteries contain strong alkaline liquids. If the alkaline liquids stick to your skin or clothes, wash immediately with running water.
Set your cameras exposure mode to Programmed auto (P), Aperture-priority auto (A), or Manual (M) mode. 200 (Shutter-priority auto (S) mode is not recommended, because setting an appropriate aperture to match the shooting distance is difficult.) Set your cameras metering system to Matrix Metering, N 35 mm Center-Weighted Metering, or Spot Metering. OFF ON STBY FLASH READY BOUNCE The shutter speed is automatically set to the flash sync speed. (Or you can intentionally set the shutter JAPAN speed to one slower than the flash sync speed.) Because the SB-22s features the same TTL flash operations as those of the SB-15 and SB-22, refer to those items corresponding to SB-15 or SB-22 in the flash photography section of your cameras instruction manual, if the SB-22s is not listed.

2 2.5.m 0.6 0.9 1.3 ft 30 40

N 35 mm

2 2.5.22
Loosen the SB-22ss mounting foot lock nut. Slide the SB-22s into the cameras accessory shoe and tighten the lock nut.
the 3 Wait fortakingready-light to come on and make sure the subject is in focus before the picture.
If the ready-light blinks for approx. 3 seconds after shooting, this indicates the light may have been insufficient for correct exposure. In this case, use a wider aperture (smaller f-number) or move closer to the subject. You can also check if the subject will receive the correct exposure by test firing the SB-22s. Refer to Checking the Correct Exposure.
For example, if the flash-to-subject distance is 5m (16.4 ft.), set the flash mode selector to A4 (f/2.8), A3 (f/4) or A2 (f/5.6) when using ISO 100 film with the angle of coverage adjusted to N-35mm. Underexposure may occur if A1 (f/8) is selected. Using an aperture wider than the maximum aperture of the lens in use is not recommended. To determine the correct flash shooting distance range and aperture, refer to Checking the Correct Exposure.
same aperture as indicated 3 Set thepanel on your camera or lenson the aperture/shooting distance range aperture ring.
To set the aperture on Zoom-Nikkor lenses having variable maximum apertures, refer to Setting Apertures on Zoom-Nikkor Lenses having Variable Maximum Apertures.
For example, when shooting with ISO 100 film, with the angle of coverage adjusted to N-35mm, selecting f/5.6 lets you take pictures of subjects at a distance of approx. 5m (16.4 ft.) away, while f/2.8 lets you take pictures of subjects approx. 10 m (32.8 ft.) away. To determine the correct aperture, use the equation and guide number table: guide number f/stop (aperture) = flash-to-subject distance (m/ft) Guide numbers (m/ft) in M mode at 20C/68F
Film speed (ISO) Normal 35mm 25 14/45.9 10/32.20/65.6 14/45.28/91.9 20/65.40/131.2 28/91.56/183.7 40/131.80/262.5 56/183.110/360.9 080/262.5
Checking the Correct Exposure
or STBY (standby) 4 Set the SB-22ss POWER switchIfto ONthe SB-22s and cameraposition.used both are not

10 m 0.6 0.9 1.3 ft N

Wait for the ready-light to come on and make sure the subject is in focus before taking the picture.

Wide 28mm

Speedlight parts
Note: Setting positions and scales shown on the aperture/shooting distance range panel below may differ from those in actual operation.
Determining an appropriate flash shooting distance range in the TTL Auto Flash TTL mode
Camera and film speed combinations
Because the flash output is automatically controlled by the SB-22s, any Nikon camera/film speed combination can be used. Correct exposure is obtained by setting the same aperture (obtained from the aperture/shooting distance range panel) as set on the camera or lens aperture ring. Exposure compensation is easy to achieve by intentionally changing the aperture on the camera or lens aperture ring.

for after approx. 80 seconds, the SB-22s shuts off automatically and the ready-light goes out to conserve battery power. This is called the standby function. To turn the SB-22s on again after it enters the standby mode, you can lightly press the shutter release button or press the FLASH button once.
Check the aperture set on the camera or lens.
In the TTL Auto Flash mode, you can set any aperture value on the camera or lens aperture ring.
For example, when shooting a subject at a distance of 5m (16.4 ft.) using ISO 100 film with the angle of coverage adjusted to N-35mm (no wide flash adapter), 28 f/stop = (in meters) = 5.91.9 f/stop = (in feet) = approx. 5.6 16.4 Therefore f/5.6 is the correct aperture. To set the aperture on Zoom-Nikkor lenses having variable maximum apertures, refer to Setting Apertures on Zoom-Nikkor Lenses having Variable Maximum Apertures.
distance range 2 Check the shootingflash shooting distance represented by the range indicator which matches the f-number in the aperture scale window.

Ready-light comes on.

Do not use the standby function: If the SB-22s is mounted on Nikon F3-series, New FM2, FM10 or FE10 cameras. If the SB-22s is mounted on Nikon FA or FE2 cameras and the shutter speed is set to M250 or B (bulb). If the SB-22s is mounted on Nikon FG or Nikonos V cameras and the shutter speed is set to M90 or B (bulb). If the SB-22s is mounted on a Nikonos V with an optional sync cord for land use connected and the shutter speed is set to M90 or B (bulb). If the SB-22s is mounted on a Nikon FM3A camera and the shutter speed is set to B (bulb). The standby function does not work: If the SB-22s is mounted on Nikon FA or FE2 cameras with Motor Drive MD-12 attached and Remote Code MC-4A (or MC-10) is connected.
For example, selecting f/4 lets you get the flash shooting distance range from 0.9m to N 35 mm 7.0m (3 ft. to 23 ft.) with angle of coverage at OFF ON STBY FLASH READY BOUNCE N-35mm and a film speed of ISO 100. JAPAN In this case, underexposure may occur when the subject is more than 7.0 m (23 ft.) away. For other shooting distance ranges, apertures, and ISO film speeds, refer to the table below.
the 4 Wait fortakingready-light to come on and make sure the subject is in focus before the picture.
Setting Apertures on Zoom-Nikkor Lenses having Variable Maximum Apertures
Setting the aperture using the camera aperture dial:
For example, F5, F100, F80-Series/N80-Series, F65-Series/N65-Series, F60-Series/N60, F50-Series/N50, F-401x/N5005, F-401s/N4004s, F-401/N4004, Pronea 600i/6i, D1 Series cameras with Nikkor lenses with a built-in CPU*: First set the lens to its minimum aperture (largest f-number) (except G-type Nikkor lenses**), then set the aperture on the camera using the aperture dial or button after zooming in or out to determine the focal length setting. In this way, the variable aperture will be automatically compensated by the camera.

For example, F4-Series, F90X/ N90s, F90-Series/ N90, F70-Series/ N70, F-801s/ N8008s, F-801/N8008, F-601/N6006, F-601M / N6000 cameras with Nikkor lenses with a built-in CPU* Check and set the aperture on the LCD panel after zooming in or out to determine the focal length setting. In this way, the variable aperture will be automatically compensated by the camera.
*Nikkor lenses with a built-in CPU incorporate CPU contacts. (See the figure on the right.) **G-type Nikkor lenses have no aperture ring. The aperture should therefore be selected from the camera body. Unlike other CPU Nikkor lenses, the aperture does not need to be set to its minimum. CPU contacts
Align the aperture ring between the green and yellow aperture indexes after zooming in or out to determine the focal length setting. If the zoom lens has a maximum aperture difference of approx. 1 or more f/stop between the longest and shortest focal length positions (see the figures below), align the aperture ring with the green aperture index for a wide setting, and align the aperture with the yellow aperture index for a telephoto setting. For intermediate focal length settings, set the aperture ring somewhere between the green and yellow aperture indexes depending on the focal length in use. Setting the aperture to f/5.6 on the AF Zoom-Nikkor 24-120mm f/3.5-5.6 lens
Yellow aperture index Close to yellow aperture index Close to green aperture index Green aperture index
At 120mm focal length setting
At 100mm focal length setting
At 50mm focal length setting
At 24mm focal length setting

4 5.m 0.6 0.9 1.ft 30 40

Usable apertures with corresponding flash shooting distance ranges
Flash mode selector in A mode 100 ISO film speed 200 1.4 1.4 1.4 A4 A3 A2 A1 1.2.5.2 2.5.2 2.5.2.5.2.5.45

800 (10001 )

Exposure Compensation in Flash Photography
Some plus compensation may be necessary when the background includes a mirror, white wall, or other highly reflective surface. Otherwise, underexposed pictures might occur. Similarly, some minus compensation may be required when the background is dark or includes subjects of low reflectivity to prevent overexposed pictures. In these cases, making exposure compensation is recommended to obtain the correct exposure. Normally, exposure compensation within the range of 2 to +1 steps is recommended.
With exposure compensation Without exposure compensation
Autofocus Flash Operation in Dim Light
For autofocus cameras only
When the light is too dim for normal autofocus operation, the SB-22ss AF assist illuminator LED automatically turns on to illuminate dark subjects when the shutter release button is pressed halfway. The AF assist illuminator LED turns off as soon as the subject is in focus.

Shooting distance range Unit: m (ft) 5.N-35mm
3.2 - 20.0 (10.5 - 65.6) 2.2 - 17.0 (7.2 - 55.8) 1.8 - 14.0 (5.9 - 45.9) 1.3 - 10.0 (4.3 - 32.8) 0.9 - 7.0 (3.0 - 23.0) 0.6 - 5.0 (2.0 - 16.4) 0.6 - 3.5 (2.0 - 11.5) 0.6 - 2.5 (2.0 - 8.2) 0.6 - 1.7 (2.0 - 5.6) 0.6 - 1.2 (2.0 - 3.9)

W-28mm

2.2 - 17.0 (7.2 - 55.8) 1.6 - 12.0 (5.2 - 39.3) 1.3 - 10.0 (4.3 - 32.8) 0.9 - 7.0 (3.0 - 23.0) 0.6 - 5.0 (2.0 - 16.4) 0.6 - 3.5 (2.0 - 11.5) 0.6 - 2.5 (2.0 - 8.2) 0.6 - 1.7 (2.0 - 5.6) 0.6 - 1.2 (2.0 - 3.9) 0.6 - 0.9 (2.0 - 3.0)

2.5.45 64

92(ft)

GN(ISO100) 28(m)

is 7 Preparation thecomplete.available flash modes: Now, refer to following
TTL Auto Flash TTL mode Non-TTL Auto Flash A mode Manual M mode Or other advanced flash techniques on the reverse side of this sheet
Battery chamber lid indices Bounce angle indicators Battery chamber lid Mounting foot lock nut Mounting foot Flash head AF assist illuminator LED window Light sensor for non-TTL auto flash operation Mount pin (for cameras featuring a safety lock system) Hot-shoe contacts Wide flash adapter lock release button Sync/multiple flash terminal Built-in wide flash adapter Aperture/shooting distance range panel
Flash mode indicator LED Flash mode selector Film speed (ISO) scale Film speed (ISO) selector Film speed (ISO) index Aperture scale (for non-TTL mode) Aperture scale BOUNCE indicator LED POWER switch Flash shooting distance range indicators Distance scale (meters/feet) Angle of coverage (N-35mm/W-28mm) index windows Ready-light FLASH button
The subject must be within the range of 1m (3.3 ft) to 5m (16.4 ft) at 20C (68F). Replace the SB-22ss batteries whenever the ready-light becomes dark or blinks after the AF assist illuminator LED turns on. If the AF assist illuminator LED comes on but no in-focus indicator appears in the cameras viewfinder with the shutter release button pressed halfway, the subject is either too far away or too dark for the camera AF-sensor even with the AF assist illuminator LED. In this case, set the flash mode selector to Manual M and focus manually.

The ready-light

Lights up : Indicates the SB-22s is recycled

and ready to fire.

Blinks :
In TTL or Non-TTL Auto flash mode, if the ready-light blinks for approx. 3 seconds after shooting, this indicates the light may have been insufficient for correct exposure. In this case, use a wider aperture (smaller f-number) or move closer to the subject.

Exposure compensation in Manual M mode
Intentionally change the aperture set on the camera or lens aperture ring. When you want an overexposed picture, set a wider aperture (smaller f-number) than the one calculated. For an underexposed picture, use a smaller aperture (larger f-number).

NIKON CORPORATION

FUJI BLDG., 2-3, MARUNOUCHI 3-CHOME, CHIYODA-KU, TOKYO 100-8331, JAPAN Printed in Japan

Bounce Flash

When taking pictures indoors, direct flash often causes harsh, unattractive shadows on the subject or background. By bouncing the light off the ceiling or walls, you can soften the shadows and produce more natural-looking portraits.
Bounce flash using diffused light Normal flash using direct flash

Close-Up Flash

In TTL Auto Flash TTL mode, when shooting subjects such as flowers or insects closer than 0.6m (2 ft), use your SB-22s off camera and utilize its built-in wide flash adapter to take close-up pictures with flash.
Setting the Built-In Wide Flash Adapter
The SB-22s comes with a wide flash adapter to increase the angle of coverage to match a 28mm lens. The guide number is reduced from 28 to 20 (ISO 100, meters) when the built-in wide flash adapter is used.

Troubleshooting

Warning indicator Cause POWER switch is turned OFF. Batteries are not installed correctly. Ready-light does not come on. Battery power is weak. Standby function is in operation. Contacts in the battery chamber (SB-22s) or battery electrodes are corroded. Ready-light blinks for approx. 3 sec. after shooting. Subject is out of the flash shooting distance range. Batteries are exhausted. Reference/remedy Preparation (4) Preparation (2) The Ready-Light Preparation (4) Clean the contacts or electrodes.

WARNING

Never attempt to disassemble or repair the SB-22s yourself as this may cause electric shock or cause the unit to malfunction, leading to possible injury. Do not drop the SB-22s or hit it against a hard surface. If dropped, do not touch the metal portions inside the flash, because they could cause electric shock or injury. Remove the batteries and take the unit to your local Nikon dealer for repair. If you detect heat, smoke, or the smell of burning, stop operation immediately and remove the batteries to prevent the unit from catching on fire or burning. Let the SB-22s cool down sufficiently before removing batteries. Then take the unit to your local Nikon dealer for repair. The SB-22s should not be exposed to rain or saltwater. If water gets inside the SB-22s, this can cause electric shock or cause the unit to catch on fire. Also never touch the flash unit with wet hands. Do not operate the SB-22s in an environment containing a combustible gas, as this may cause the unit to catch on fire or result in an explosion. Keep batteries out of the reach of children. If a battery is accidentally swallowed, call a doctor immediately. When replacing batteries, replace all four batteries at the same time, do not mix battery types or brands, do not use old with new batteries, and never reverse the polarity of the batteries when installing. Otherwise, the batteries may catch on fire or explode, due the possible leakage of corrosive liquids. In the event that corrosive liquids do seep from the batteries, avoid touching the liquids. Certain types of batteries contain strong alkaline liquids which can cause chemical burns. If the alkaline liquids stick to your skin or clothes, wash immediately with running water.

Setting the wide flash adapter
1 Tilt the flash head to the 90 position. 2 Slide out.the wide flash adapter in the direction of the arrow as far as it will go
In color photography, select white or highly reflective surfaces to bounce the light off of. Otherwise, your pictures will come out with an unnatural color cast similar to that of the reflecting surface.
Checking the Correct Exposure The Ready-Light Allow longer recycling time between flashes or wait until they cool off. Notes on Batteries Bounce Flash Operation Non-TTL Auto Flash A Mode (1) Manual Flash M Mode (1)
the SB-22s to your camera using an optional 1 Connect optional TTL Remote Cord SC-17 (or SC-24 for F4 TTL Remote aCord. Use an cameras with HighMagnification Finder DW-20 or DW-21, and F5 cameras with a HighMagnification Finder DW-30 or DW-31) for connecting the SB-22s to your camera. The subject cannot be sufficiently illuminated if the flash unit is attached to the cameras accessory shoe. For details on connections, refer to the SC-17 or SC-24s instruction manual.
Ready-light takes longer to light up.
Lithium batteries become hot by repeated use which activate their safety circuit, thus cutting off power. SB-22ss flash head is tilted from the front position. Flash mode selector is set to A1, A2, A3, A4 or M, and cameras exposure mode is set to Programmed auto or Shutter-priority auto mode.
Tilt up the SB-22ss flash head to 60 or more.
BOUNCE indicator LED lights up.
Set the cameras exposure mode to Aperture-priority auto (A) or Manual (M).
Set your cameras metering system to any setting. The shutter speed is automatically set to the flash sync speed when the SB-22ss POWER is turned on. (Or you can intentionally set the shutter speed to one slower than the flash sync speed.) For the FM3A camera, set a shutter speed slower than 1/250 sec., the flash sync speed.
Do not tilt down the flash head from 90 position when the wide flash adapter is extended midway.
Shutter cannot be released even when the ready-light lights up.
Return the flash head to its original position
The BOUNCE indicator LED blinks when the flash head is tilted. The flash head can be tilted up to 90. Intermediate settings can also be used.
3 Set the flash mode selector to TTL.

A M TTL I SO

Tips on Speedlight Care
When the wide flash adapter is set, the angle of coverage changes from N-35mm to W-28mm, and the distance scale also moves. Use a blower brush to remove dirt and dust from the SB-22s and clean it with a soft, clean cloth. Never use commercial cleaners containing thinner, benzene, or alcohol as they could damage its plastic parts. When storing the SB-22s for two weeks or longer, remove the batteries to prevent battery leakage. Also once a month, insert fresh batteries and fire the unit several times to reform its capacitor and keep the SB-22s in top working order. Finally make sure the ready-light is on, before turning the power off and removing the batteries. Keep the SB-22s away from chemicals such as camphor or naphthalene. Also avoid exposing it to magnetic waves from TVs or radios. Never store the SB-22s in the truck or glove compartment of a vehicle during the summer nor place it in front of a heater.

If the angle of the flash head is not far enough off axis from the subject, uneven illumination will result from a combination of direct and bounced flash.

2 2.5.11 16

Do not fire the flash directly into a persons eyes at close range as this may damage the retina, leading to partial or complete blindness. Keep the SB-22s out of the reach of children. This will prevent them from swallowing batteries or getting an electric shock. Do not throw used batteries into a fire. Do not short circuit, disassemble, or heat a battery; this may cause it to explode or catch on fire.
Any metering system is acceptable. For Nikon FM3A, New FM2 and FM10 cameras, manually set the shutter speed to the flash sync shutter speed or slower. For other cameras, the shutter speed is automatically set to the flash sync speed. (Or you can intentionally set the shutter speed to one slower than the flash sync speed.) Refer to your cameras instruction manual for details.
Detaching the wide flash adapter
Correct exposure cannot be obtained in non-TTL auto flash A mode.
the built-in 4 Set subject. wide flash adapter. Then adjust the flash head toward the
Refer to Setting the Built-In Wide Flash Adapter. The angle of coverage changes from N-35mm to W-28mm.
the SB-22ss flash mode A1, 3 Set aperture on the camera orselector to TTL,ring. A2, A3 or A4, then set the lens aperture
1 Tilt the flash head to the 90 position. the wide 2 While pushinginside the flash adapter.lock button adapter back flash head

, slide the wide flash

I SO 2.5.11 16
With bounce flash, there is a 2 to 3 stop light loss when compared with normal TTL or nonTTL auto flash modes. Therefore, you should open up the lens by 2 to 3 stops (use smaller f-numbers) and bracket your exposures, whenever possible. For details on the flash mode selector (TTL, A1-A4) and aperture values, refer to TTL Auto Flash TTL Mode, Non-TTL Auto Flash A Mode, or Checking the Correct Exposure.
the aperture on the lens 5 Set f/stop using the equationaperture ring or on the camera by calculating the and table below.
coefficient f/stop (aperture) flash-to-subject distance (m/ft) ISO film speed and coefficient (m/ft)
ISO film speed Coefficient 25 1.5 (4.9) 50 2.2 (7.2) (9.8) 200 4.3 (14) (20) 800 8.5 (27.9) 1000 9.6 (31.5)

Notes on Batteries

Handling batteries Battery power tends to weaken as the temperature drops. At low temperatures, the number of flashes decrease and recycling time is longer. NiCd, Ni-MH and lithium batteries feature greater efficiency at low temperatures, usable as low as 20C (4F). Alkaline-manganese and zinc-carbon batteries are not recommended as their performance become noticeably degraded at 10C (14 F) for alkalinemanganese and 0C (32F) for zinc-carbon batteries. In either case, battery performance may differ with each brand, due to modification in specifications or improvement in performance. Using lithium batteries Lithium batteries incorporate internal safety switches. When they become hot, their safety circuits are activated, cutting off power. Battery power will recover if you stop using them, allowing their temperature to return to normal. Using rechargeable NiCd and Ni-MH batteries Overcharging and excessive use may shorten battery life. Always make certain to turn the SB-22s off when not in use. Because flash consumes a large amount of battery power, rechargeable batteries may not operate properly before reaching the end of their stated life-span or the number of charging/discharging as specified by the battery manufacturer.

Always follow the warning instructions printed on batteries to prevent them from becoming hot, leaking corrosive liquids, catching on fire, or exploding. When recharging NiCd or Ni-MH batteries, be sure to use the battery charger specified by the battery maker and read the instructions thoroughly. Do not recharge NiCd or Ni-MH batteries with their terminals reversed in the charger or before the batteries have cooled off sufficiently, as this may cause them to leak corrosive liquids, become hot, catch on fire, or explode. Non-rechargeable batteries such as zinc-carbon, alkaline-manganese and lithium batteries should not be charged in a battery charger as they may become hot, catch on fire, explode, or leak corrosive liquids.
If the ready-light blinks for approx. 3 seconds after shooting, this indicates the light may have been insufficient for correct exposure. In this case, use a wider aperture or reduce the distance between the subject and the SB-22s, where the distance is measured from the flash to the bounce surface and back again to the subject. You can also check if the subject will receive the correct exposure by test firing the SB-22s. Refer to Checking the Correct Exposure.
For example, with a subject 0.5m (1.6 ft.) away from the SB-22ss flash head using ISO 100 film and the wide flash adapter in place, the suggested aperture is: 3 0.5 9.8 f/stop 1.6 f/stop (in meters) = 6 (in feet) = approx. 6
3 Return the flash head to its original position
Therefore, you should use f/6 or smaller (larger f-number), such as f/8, f/11 or f/16.
When shooting subjects closer than 1 m (3.3 ft.)
Tilt the flash head down to the -7 position when shooting subjects 1 m (approx. 3.3 ft.) or closer to give sufficient light to the subject with the SB-22s mounted on camera. The BOUNCE indicator LED blinks when the flash head is tilted down to -7. Use of the wide flash adapter is recommended.
the 6 Wait fortakingready-light to come on and make sure the subject is in focus before the picture.
If the ready-light blinks for approx. 3 seconds after shooting, this indicates the light may have been insufficient for correct exposure. In this case, use a wider aperture (smaller f-number) or move closer to the subject.

Specifications

Electronic construction Automatic Insulated Gate Bipolar Transistor (IGBT) and series circuitry. Power source Four AA-type zinc-carbon, alkaline-manganese, lithium (1.5V), NiCd (rechargeable) or Ni-MH (rechargeable) penlight batteries. Guide number (at ISO 100, m) 28 at N-35mm; 20 at W-28mm (with wide flash adapter) Angle of coverage
Horizontal Vertical Usable lens 35mm or longer 28mm or longer

ISO 5.32

m 0.ft 2

Multiple Flash Operation

To eliminate harsh shadows produced by a single flash unit, add additional illumination to the background, or create special lighting effects not possible with a single flash unit, you can attach Nikon Speedlights in series.
Flash shooting with more than one unit Flash shooting with one flash unit

Optional Accessories

TTL multiple flash operation NOTE
TTL multiple flash operation is not possible with Nikon New FM2, FM10, FE10 and D1 Series cameras. In this case, perform non-TTL or manual multiple flash operation using the SU-4.
The SB-22ss sync/multiple flash terminal
This terminal is provided for connecting the SB-22s to your camera using Sync Cord SC-11 or SC-15 (for instance, if your camera does not have an accessory shoe) or when you want to perform Multiple Flash photography in Manual M mode with the SB-22s.

N-35mm W-28mm

ON ST OFF

BOUN CE

(ft) ) 92 28(m 100) GN(ISO
1 Or use the TTL Remote Cord SC-17/SC-24 or Power Bracket Unit SK-6 instead. main flash unit the unit(s) 2 Connect themore TTL RemotetoCordssecondary flashthe TTL Multi-Flash Use one or SC-18/SC-19 or
Connect the main flash unit to the camera directly.
Multiple flash operation can be accomplished in two ways: (1) by connecting a Speedlight to the camera using a sync or remote cord such as TTL Remote Cord SC-17 or (2) by mounting a Speedlight on the Wireless Slave Flash Controller SU-4 (optional). In both cases, TTL multiple flash operation is possible with Nikon cameras in the TTL Auto Flash mode. Adapter AS-10. Use the Wireless Slave Flash Controller SU-4 to control remotely one or more slave flash units in the TTL flash mode. For other optional remote cords, refer to Optional Accessories.
When the SB-22ss sync terminal is connected to your camera via the Sync Cord SC-11 or SC-15, automatic flash sync speed setting and viewfinder ready-light no longer function. To retain these features, use optional TTL Remote Cord SC-17 or SC-24 which attach directly to your cameras accessory shoe. Sync Cord SC-11 and SC-15 Sync Cords SC-11 and SC-15 are handy when you want to use the SB-22s off-camera or for use with cameras without accessory shoes. The SC-11 is approx. 25 cm (9.8 in.) long and the SC-15 is approx. 1m (3.2 ft) long. Use Sync Terminal Adapter AS-15 when connecting the SB-22s to cameras not having a sync terminal. TTL Remote Cord SC-17 and SC-24 The TTL Remote Cords SC-17/24 provide TTL Auto Flash operation when the SB-22s is used off-camera. It comes with one tripod socket and two TTL multiple flash terminals. Both the SC-17 and SC-24 are approx. 1.5m (4.9 ft) long. TTL Multi-Flash Sync Cord SC-18 and SC-19 Multi-Flash Sync Cords SC-18 or SC-19 are useful for connecting the SB-22s to the multiple flash terminal of the SC-17 (SC-24) or AS-10 for TTL multiple flash operation. The SC-18 is approx. 1.5 m (4.9 ft) long, and the SC-19 is approx. 3 m (9.8 ft) long. TTL Multi-Flash Adapter AS-10 Use Multi-Flash Adapter AS-10 when connecting more than three flash units together for TTL multiple flash operation, or if the secondary flash units are not equipped with multiple flash terminals. The AS-10 comes with one tripod socket and three TTL multiple flash terminals. Sync Terminal Adapter AS-15 The Sync Terminal Adapter AS-15 is necessary when using Sync Cords SC-11/SC-15 to connect the flash unit to cameras not having a sync terminal. Flash Unit Coupler AS-4 and AS-7 Necessary when mounting the SB-22s on F3-series cameras. In this case, TTL auto flash is not possible. Wireless Slave Flash Controller SU-4 Useful for multiple flash photography, the SU-4 features a built-in, movable light sensor and an accessory shoe for attachment of a slave Speedlight. The SU-4s light sensor not only triggers the slave unit to fire in unison with the master flash, but controls the flash duration of the slave unit in sync with the master unit to provide TTL, non-TTL, or Manual operation. TTL Flash Unit Coupler AS-17 for F3-Series cameras Dedicated adapter for F3-Series cameras providing TTL flash operation with Nikon Speedlights such as SB-29 and SB-28 featuring ISO-type mounting foot (not designed for F3).

Bounce capability Flash head can be tilted down to -7 or up to 90. The BOUNCE indicator LED blinks whenever the flash head is tilted. POWER switch Three positions are provided: OFF, ON and STBY (standby). At STBY position: the SB-22s automatically turns itself off to conserve battery when the flash is not used for approx. 80 seconds. Number of flashes and recycling times
Batteries*1 AA-type zinc-carbon AA-type alkaline-manganese AA-type NiCd (700mAh)*4 AA-type Ni-MH (1200mAh) AA-type lithium (1.5V)
Min. recycling time (approx.)*2 No. of flashes (approx.)*3
Set each flash unit by considering its direction and distance.
Please note that the brightness of flash illumination is inversely proportional to the square of the distance between the flash unit and the subject when the same Speedlight models are used for both the master and slave Speedlights. For example, if the flash-to-subject distance is a reference unit of 1 (e.g., 1m), the brightness will be one-half that when the subject is 1.4 times away, and onequarter when the subject is twice as far away. For details on connections, refer to the SC-17, SC-18, SC-19, or SC-24s instruction manual.
10 sec. 5 sec. 3.6 sec. 4.5 sec. 5.5 sec.
Notes on multiple flash operation using a sync or remote cord:
SB-11, SB-14, SB-140 and SB-21B Speedlights cannot be used with Nikon F-401/N4004 or F-401s/N4004s as either main or secondary units. In multiple flash operation, if the electric current in the synchro circuit exceeds a certain level, you may not be able to take a second shot after the first. In this case, disconnect the main flash unit from the camera. This resets the circuits so you can resume shooting. In multiple flash operation, take care that the combined total of the coefficients in the table below for all flash units used together does not exceed 20 at 20C (68F), or 13 at 40C (104F). Speedlight coefficient per each unit
Speedlight SB-50DX, SB-29, SB-28/28DX, SB-27, SB-26, SB-25, SB-24, SB-22s, SB-14, SB-11, SB-140 SB-23, SB-21, SB-17, SB-16, SB-15 SB-22 SB-20
Coefficient numbers are in units of 70A.

4 Turn on all flash units and make sure their standby functions are not activated. Set the flash mode on all flash units to TTL. Follow the same procedures as in normal TTL Auto Flash TTL mode.
Manual multiple flash operation
*1 With fresh batteries *2 Duration until the ready-light comes on after firing at full manual output. *3 Total number of flashes when fired at full manual output at an interval of 30 seconds without using the AF assist illuminator LED. *mAh NiCd batteries provide approx. 1.4 times the number of flashes of 700 mAh NiCd batteries with the same recycling time.

Coefficient 6 9

1 Attach the SB-22s to the cameras accessory shoe. flash terminal of the secondary flash unit(s). 2 Connect the SB-22s to the syncTTL multiple flash operation, or Sync Cord Use the same cords as used for
SC-11 or coiled Sync Cord SC-15. Use the Wireless Slave Flash Controller SU-4 to control remotely one or more slave flash units in the Manual flash mode. For usable optional remote cords, refer to Optional Accessories.
Notes on multiple flash operation using the Wireless Slave Flash Controller SU-4 (optional):
TTL, non-TTL or Manual multiple flash operation is possible by using the cameras builtin Speedlight or a Speedlight mounted on the cameras hot shoe as the master flash unit, and one or more Speedlights mounted on Wireless Slave Flash Controller SU-4s as the slave flash units. The SU-4s built-in light sensor not only detects when the master flash unit fires to trigger the slave flash unit, but also controls the flash duration of the slave flash unit in sync with the master flash unit. These Nikon Speedlights are usable: SB-29, SB-28/28DX, SB-27, SB-26, SB-25, SB-24, SB-23, SB-22s, SB-22, SB-20, SB-18, SB-16B, SB-15 For more information, refer to the instruction manual provided with the SU-4.
flash unit distance. 3 Set eachnote that theby considering its direction andinversely proportional to Please brightness of flash illumination is
the square of the distance between the flash unit and the subject. See the example described in TTL multiple flash operation above. For details on connections, refer to the SC-17, SC-18, SC-19, or SC-24s instruction manual.
Flash exposure control Three flash modes are provided: TTL, non-TTL (A1, A2, A3, A4) and M. TTL mode is not possible with Nikon F3-series, New FM2, FM10, FE10 cameras. Ready-light Lights up when SB-22s is recycled and ready to fire. Blinks for 3 seconds when flash fires at its maximum output, indicating light may have been insufficient (in TTL and non-TTL (A1-A4) modes). FLASH button Performs test firing for correct exposure determination. Can turn the SB-22s on again after the unit enters standby mode. AF assist illumination Automatically fires LED beam toward subject when performing autofocus in dim light or in the dark with Nikon AF cameras. Flash duration 1/1100 sec. @ full manual output Other features Sync/multiple flash terminal Dimensions (W x H x D) Approx. 68 x 105 x 80mm (2.7 x 4.1 x 3.1 in.) Weight (without batteries) Approx. 210g (7.4 oz.) Accessories supplied Soft Case SS-22s All performance data are for normal-temperature operation (20C/68F). Specifications and design are subject to change without notice.