Fast Track to Wireless Speedlights
The Nikon Creative Lighting System offers a comprehensive selection of revolutionary lighting tools to match virtually any need. This system features the worlds most intelligent and versatile flash units, including the groundbreaking Nikon SB-900, as well as the SB-800, SB-600, SB-R200 Speedlights, and the innovative Wireless Close-up Speedlight System. The end result is unprecedented levels of accuracy, automation, integration and control that only Nikon could deliver.
ADVANCED WIRELESS FLASH USING Nikons CREATIVE LIGHTING SYSTEM
The Nikon SB-900, SB-800 or SU-800 Wireless Commander can be used to control other SB-900, SB-800, SB-600 and SB-R200 Speedlight units wirelessly. To do so, the SB-900 or SB-800 Speedlight must be connected to any i-TTL compatible cameras hotshoe to enable these speedlights (or SU-800 Wireless Commander) as a Master Flash Unit. Follow the steps below.

Photo Joe McNally

Setting the SB-900 as a Master Speedlight Unit
Set the SB-900 to the Master/Commander mode by using the Power ON-OFF switch/wireless setting switch. 1. Turn the switch while holding down the button in the center. 2. Align the index on the Power ON-OFF switch/wireless setting switch to MASTER. Setting the flash mode, flash output level compensation values, and channel number on the master flash unit 1. Press the Function button 1 on the Master flash unit to highlight M. 2. Press the MODE button, then turn the selector dial to choose the desired flash mode, and press the OK button. TTL Through the lens metering A M Auto Aperture Manual
Function button 1 Function button 2
- - - No light output (although in M - - a preflash will occur)
3. Press the Function button 2, then turn the selector dial to choose the desired flash output level compensation value, and press the OK button. 4. Press the Function button 1 to highlight Group A.
Turn the selector dial to choose a group other than A.
5. Repeat procedures 2, 3 above to set the flash mode and flash output level compensation values of the remote flash units in Group A. 6. In the same way as with Group A, set the flash mode and flash output level compensation values of the remote flash unit in Group B and C.
Note: After setting the output compensation value press OK twice to reveal Ch above Function button 2.
7. Press the Function button 2, then turn the selector dial to set a channel number, and press the OK button.
Setting the SB-800 as a Master Flash Unit
1. With the unit on, press and hold SEL for two seconds. The display will change. 2. Locate the shaded box and use the toggle to highlight (The wireless symbol). 3. Press SEL for one second. The one will change to two and the OFF selection on the right will become shaded. 4. Scroll down and select MASTER by highlighting it and pressing SEL for two seconds. The display will change to the Master view. 5. Press SEL to highlight M. By pressing +/ you can change the flash output compensation value for the M group. Pressing MODE while a group (M, A, B or C) is highlighted will change how the Speedlights in that group will react. TTL Through the lens metering A M Auto Aperture Manual
- - - No light output (although in M - - a preflash will occur) Press SEL to jump from group M to A to B to C. Set the amount of flash output compensation for each group using +/ as you go. 6. Use SEL to highlight CH and use +/ to select the channel you will be working in. (There are 4 channels, this allows multiple photographers using the Nikon Creative Lighting System to control only their own Speedlights.)
Note: The channel you choose for the Master Speedlight must be the same channel the remote units are set to.
7. Attach the Master Speedlight to your camera.
Note: During shooting, if you wish to change the power output of the Remote Flash units, do so from the Master SB-900, SB-800. The change will take effect immediately. The SB-900, SB-800 or SU-800 Wireless Commander act as a commander units when placed in Master Mode. For other SB-900, SB-800, SB-600 and SB-R200 Speedlight units to fire wirelessly, they must be set to Remote.

For more information on setting your wireless Speedlights please see your instruction manual.

REMOTE WIRELESS FLASH

The Nikon SB-900, SB-800, SB-600 and SB-R200 Speedlights can be set as remote units and can be triggered by using an on-camera SB-900 or SB-800 set in Master Mode, directly from the built-in flash on the D80, D90, D200, D300 or using the SU-800 Wireless Commander.
Setting the SB-900 as a Wireless Remote Unit
You can set the SB-900 for remote operation using the Power ON-OFF switch/wireless setting switch. 1. Turn the switch while holding down the button in the center. 2. Align the index on the Power ON-OFF switch/wireless setting switch to REMOTE. Setting a group and channel number on the remote flash units 1. Press the Function button 1, then turn the selector dial to choose a desired group name, and press the OK button.
Group name and channel number being set appears larger. For remote flash units where the flash mode and flash output level compensation values are to be set identically, place these flash units into the same group.
2. Press the Function button 2, then turn the selector dial to choose a desired channel number, and press the OK button.
Be sure to choose the same channel number as set on the Master flash unit or in the Commander mode on your camera.
Setting the SB-800 as a Wireless Remote Unit
1. With the unit on, press and hold SEL button for two seconds. 2. Locate the shaded box and use the toggle to highlight (The wireless symbol). 3. Press SEL for one second. The one will change to two
4. Scroll down and select REMOTE by highlighting it and pressing SEL for two seconds. The display will change to the Remote view. 5. Press SEL to highlight CH, use +/ to select the channel. (The Remote and Master units must be set to the same channel or they will not communicate.) 6. Press SEL again to highlight the group. Use +/ to choose Group A, B or C. (The amount of output compensation set for Groups A, B and C on the Master Flash will determine the amount of output from the Remote Speedlights.)

Setting the SB-600 as a Wireless Remote Unit
1. With the unit on, press and hold the ZOOM and the together for two seconds. 2. Press either the ZOOM or MODE button to select wireless mode ON/OFF. 3. Press ON/OFF for one second. The flash will be set in the Wireless Remote mode. (Default: CH 3, Group A) 4. Press MODE to highlight the channel (1, 2, 3 or 4) and use +/ to select the same channel as the Master Flash. 5. Press MODE again and choose a group (A, B or C). The amount of output compensation set for that group on the Master Flash will determine the amount of output from the Remote Speedlight.
To exit Wireless and return to Normal TTL operation
To reset the SB-600 and SB-800 units to normal TTL operation, reverse the steps above or hold ON/OFF and MODE button for two seconds. To exit remote operation of the SB-900 simply turn the ON-OFF switch/wireless settings to the ON position.
To set the SB-R200 Remote Speedlight to the desired Group and Channel, simply rotate the dial for that function.
Nikons EXCLUSIVE BUILT-IN i-TTL FLASH SYSTEM WITH WIRELESS CAPABILITIES WITH THE D700, D300, D200, D90 AND D80 DIGITAL SLRs
1. The Wireless Flash Commander mode option can be selected within the Custom Settings menu under the built-in flash option of the D700, D300, D200, D90 and D80 cameras. D700 Custom Setting: e3 D300 Custom Setting: e3 D200 Custom Setting: e3 D90 Custom Setting: e2 D80 Custom Setting: 22 2. When you enter the Commander mode, the built-in flash, Group A and Group B are all activated and set to TTL with zero exposure compensation. In this scenario, the built-in flash will send a pre-flash signal for the remote units to fire, as well as trigger the remote Speedlights and factor into the lighting scheme and final exposure. 3. Flash compensation can be adjusted for Groups A and B, as well as the built-in flash. Press the cameras Multi-selector right or left to move into the Mode or Compensation windows for the built-in flash and both Groups. Use the up and down arrows with the Multi-selector to set the desired values. 4. The built-in flash, as well as the A and B Groups, can be set to fire and be factored into the exposure, or turned off individually, based on your lighting requirements. Toggle the Multi-selector to the right to enter the Mode window for the item you would like to turn off. Toggle the Multi-selector down until you see the dashed lines. This means that the built-in flash or selected Speedlight will NOT fire.*

*Note: Although you may turn off the built-in flash from being calculated into the exposure, the built-in flash unit must stay in the up position, as it will still send the pre-flash signal to control the remote units.
Once you have set the Commander mode as desired, be sure that the channel you have selected matches the channel set on the remote units. Also, be sure to press the OK button to confirm and set the Commander mode.
Note: Wireless Flash Commander Mode works in only P, S, A or M and is not available in Scene Modes. The D70/D70s Commander mode operation communicates only in Channel 3/Group A.
Nikons CREATIVE LIGHTING SYSTEM (CLS)
Offering unprecedented levels of automation and integration, Nikon's flagship SB-900, powerful SB-800, versatile SB-600, SB-R200 and convenient SB-400 Speedlights deliver dependably brilliant flash performance in concert with CLS-compatible Nikon D-SLRs.* Their simple, intuitive operation allows even novice photographers to achieve incredible flash exposures. Their groundbreaking technology enables enthusiasts and seasoned pros to accomplish expressive flash photography with easy, accurate control of wireless multiple Speedlight arrays. Whatever your skill level, Nikon Speedlights simply give you the quality light you need.
SB-900 SPEEDLIGHT Prod. No. 4807
SB-800 SPEEDLIGHT Prod. No. 4801
SB-600 SPEEDLIGHT Prod. No. 4802
SB-400 SPEEDLIGHT** Prod. No. 4806
*Compatible cameras include the D3X, D3, D700, D2XS, D2X, D2HS, D2H, D300, D200, D90, D80, D70S, D70, D50, D60, D40X, and D40 digital SLRs, as well as the F6 35mm SLR. **SB-400 operates as a stand alone speedlight only.
WIRELESS CLOSE-UP SPEEDLIGHT SYSTEM
The Wireless Close-Up Speedlight System from Nikon, the world leader in wireless remote flash operation, delivers the ultimate tools for creative close-up photography with a wide variety of convenient wireless flash configurations. Available in two key configurations, the R1* and R1C1, offering unprecedented versatility and control for close-up and other lighting challenges. R1C1 WIRELESS SPEEDLIGHT SYSTEM Prod. No. 4803
SB-R200 SPEEDLIGHT Prod. No. 4805
SU-800 WIRELESS SPEEDLIGHT COMMANDER Prod. No. 4794
Nikon Schools A Hands-on Guide to Creative Lighting DVD Prod. No. 11484
*The R1 configuration is recommended for use with Nikon CLS-compatible cameras with a built-in flash with a Wireless Commander mode.

SPEEDLIGHT DVD GLOSSARY

Ambient Light The natural, available light in a scene. Also known as existing light. AF-Assist Illuminator LED light on the camera that illuminates the subject, making it possible to focus on the subject even in total darkness. Automatic Power Zoom The zoom head is automatically adjusted according to the focal length of the lens in use. Backlighting The light coming from behind the subject. Bounce Lighting Using the bounce feature on a Speedlight, light is bounced off a reflector, ceiling or wall to soften or diffuse the lights intensity. Chiaroscuro Italian for light-dark, a term in art and photography for a contrast between light and dark. CLS Creative Lighting System Nikons Speedlight system. Feathering Pan or tilting the light so that its dim edge is used to light the subject. Flash Output Level Compensation Flash compensation used to increase or decrease the output power of a Nikon Speedlight unit. Fill Flash A technique to brighten dark shadow areas, often used when the subject is located in the dark shadow. Fill Light A light that supplements the key light without changing its character, used to lighten or open shadows within a scene. Front lighting Light coming from the direction of the camera toward the subject. FP Auto High-Speed Sync Auto high-speed flash synchronization enables CLScompatible cameras and Speedlights to sync at the cameras highest possible shutter speed. This technique minimizes depth of field and freezes high-speed subjects. Flash Synchronization A means by which a Speedlight is fired at precisely the moment when the camera's shutter is at its peak opening. Also referred to as flash sync. Front Curtain Sync Also referred to as Normal sync, the flash fires immediately after the front curtain opens completely. FV Flash Value Lock Locks in the appropriate flash exposure for the main subject, which remains locked whether the aperture, composition or lens zoom position is changed. Guide Number (Flash) Guide numbers proclaim the light output of electronic flash units. The guide number divided by subject distance represents the theoretical f-stop for an exposure. i-TTL metering Nikons Intelligent Through-The-Lens (TTL) flash metering using monitor pre-flashes for unprecedented levels of precision and performance. Key Light Also called "main light is the principal source of light on a subject or a scene. Master Speedlight Unit CLS-compatible Speedlight unit, built-in flash or wireless device (SB-800, SB-900 or SU-800 Wireless Commander) that works in the Commander mode to send monitor pre-flash and firing signals to remote Speedlights Monitor pre-flash A series of pre-flash firings detected by the cameras TTL multi-sensor, analyzed for brightness and contrast. Also used to communicate output values to remote Speedlight units in multiple wireless lighting. Rear Curtain Sync The flash fires just before the rear (second) curtain starts to close for special effects photography where the blur appears behind the subject. Reflectors Flat devices, typically white, silver, or gold, that redirect light to soften or fill in areas of a subject or scene. Remote Speedlight Unit CLS-compatible Speedlight that can be set to fire as a wireless remote unit. Repeating Flash The Speedlight delivers a stroboscopic effect, firing the flash continuously at selected rates. Side lighting Light shining on the subject from the side relative to the camera, often casting long shadows. Slow Sync Flash The flash is controlled at a slower shutter speed to obtain the correct exposure for both the main subject and the background in low light situations or at night. TTL Through the lens. Any metering system - ambient exposure metering or flash metering - which works through the lens.

Cover Photo Mike Corrado

08-458
Nikon Inc., 1300 Walt Whitman Road, Melville, NY 11747 www.nikonusa.com 1-800-Nikon-UX

SLR-SBINST-34-12/08