INJURED PERSONS

NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations.
THREE-POINT TYPE SEAT BELT WITH RETRACTOR
Every person who drives or rides in this vehicle should use a seat belt at all times.
Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop.
1-16 SafetySeats, seat belts and supplemental restraint system

WRS0174

LRS0594

LRS0595

Manual front seat shown
Fastening the seat belts (Front seats all models and rear seats Crew cab models)
Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.
Position the lap belt portion low and snug on the hips as shown. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest.
Adjust the seat. See Seats earlier in this section.
The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat. If the seat belt cannot be pulled from its fully retracted position, firmly pull the belt and release it. Then smoothly pull the belt out of the retractor.
The front passenger seat and the rear seating positions three-point seat belts have a locking mechanism for child restraint installation. It is referred to as the automatic locking mode or child restraint mode.
SafetySeats, seat belts and supplemental restraint system 1-17
When the automatic locking mechanism is activated the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully retracted. Once retracted, the seat belt is in the emergency locking mode. See Child restraints later in this section for more information. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. It can also change the operation of the front passenger air bag. See Front passenger air bag and status light later in this section.

LIC0688

Type A

Type B

Type C
HEADLIGHT CONTROL SWITCH Lighting
Use the headlights with the engine running to avoid discharging the vehicle battery.
When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. When turning the switch to the position, the headlights come on and all the other lights remain on.
Instruments and controls 2-25
To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 tion. 2. Turn the ignition key to ON. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain ON for 5 minutes. If another door is opened during the 5 minutes, then the 5 minute timer is reset.

LIC0561

Autolight system (if so equipped)
The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: Turn on the headlights, front parking, tail, license plate and instrument panel lights automatically when it is dark. Turn off all the lights when it is light. Keep all the lights on for 45 seconds after you turn the key to OFF and all doors are closed.
To turn the autolight system off, turn the switch to the OFF, , or position.

LIC0835

Be sure you do not put anything on top of 1 the autolight sensor located in the top side of the instrument panel. The autolight sensor controls the autolight; if it is covered, the autolight sensor reacts as if it is dark out and the headlights will illuminate. If this occurs while parked with the engine off and the key in the ON position, your vehicles battery could become discharged.
2-26 Instruments and controls
After the headlights automatically turn off with the or position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the or position.
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
Even though the battery saver feature automatically turns off the headlights after a period of time, you should turn the headlight switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.

LIC0562

Headlight beam select
DAYTIME RUNNING LIGHT SYSTEM (Canada only)
The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the position. Turn the OFF position or in the headlight switch to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate when the parking brake is released. The daytime running lights will remain on until the ignition switch is turned off.

Instruments and controls 2-47

INTERIOR LIGHTS

If the auto reverse function malfunctions and repeats opening or tilting up the sunroof, keep pushing the tilt down switch within 5 seconds after it happens, then the sunroof will fully close gradually. In this case, make sure nothing is caught in the sunroof.
If the sunroof does not close
Have your NISSAN dealer check and repair the sunroof.

LIC0789

Type A The interior lights have a three-position switch and operate regardless of ignition switch position.
1 When the switch is in the ON position , the interior lights illuminate, regardless of door position. The lights will go off after about 30 minutes unless the ignition key is in the ACC or ON position. 2 When the switch is in the O position , the interior lights will stay on for about 30 seconds when:

Sunshade

Open and close the sunshade by sliding it forward or backward.
2-48 Instruments and controls
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

LIC0792

LIC0630
Type B The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. The drivers door is opened and then closed while the key is removed from the ignition switch. The key is removed from the ignition switch while all doors are closed. The lights will turn off while the 30 second timer is activated when:
Type C The drivers door is locked by the keyfob, a key, or the power door lock switch. The ignition switch is turned ON. The lights will turn off automatically after 30 minutes while doors are open to prevent the battery from becoming discharged.
3 When the switch is in the OFF position , the interior lights do not illuminate, regardless of door position.
Instruments and controls 2-49
PERSONAL LIGHTS (if so equipped)
MAP LIGHTS (if so equipped)
HOMELINK UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLink Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink Universal Transceiver: Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems. Is powered by your vehicles battery. No separate batteries are required. If the vehicles battery is discharged or is disconnected, HomeLink will retain all programming. Once the HomeLink Universal Transceiver is programmed, retain the original transmitter for future programming procedures (Example: new vehicle purchases). Upon sale of the vehicle, the programmed HomeLink Universal Transceiver buttons should be erased for security purposes. For additional information refer to Programming HomeLink later in this section.

5-20 Starting and driving
4WD Shift Switch Position

Wheels Driven

Indicator Light 4WD shift Transfer 4LO position Use Conditions 4WD Shift Procedure Move the 4WD switch. 2WD <> 4H 4WD shift indicator light will indicate transfer shift position engaged.
Rear wheels 2WD 4 wheels 4H Neutral *1 May blink 4LO 4 wheels Illuminated
For driving on dry, paved roads (Economy drive) or state dynamometer I/M testing For driving on rocky, sandy or snowcovered roads Neutral disengages the automatic transmission mechanical parking lock, which will allow the vehicle to roll. Do not leave the transfer shift position in Neutral.*2
For use when maximum power and traction is required (for example: on steep grades or rocky, sandy, muddy roads)
1. Stop the vehicle. 2. For automatic transmission vehicles: Shift the transmission selector to the (N) position with the brake pedal depressed. For manual transmission vehicles: Shift the transmission shift lever to the (N) position with the clutch depressed. 3. For automatic transmission vehicles: Depress and turn the 4WD shift switch to 4LO or 4H with the brake pedal depressed. For manual transmission vehicles: Depress and turn the 4WD switch to 4LO or 4H with the clutch pedal depressed. THE TRANSFER CASE DOES NOT ENGAGE BETWEEN 4H AND 4LO (OR 4LO TO 4H) UNLESS YOU HAVE FIRST STOPPED THE VEHICLE, DEPRESSED THE BRAKE PEDAL AND MOVED THE TRANSMISSION SELECTOR TO NEUTRAL FOR AUTOMATIC TRANSMISSION VEHICLES. FOR MANUAL TRANSMISSION VEHICLES YOU MUST MOVE THE TRANSMISSION SHIFT LEVER TO NEUTRAL. *3
*1: Before moving the transmission selector or shift lever from neutral, wait until the 4LO indicator light stays on steady. This indicates that the 4WD shift procedure is completed and the transfer gear is correctly set in the 4LO position. If the vehicle is shifted into gear before the indicator is on steady, the transfer gear may grind, not engage correctly or stay in the neutral position. - If the 4WD warning light illuminates, perform the following procedure to return the transfer case to correct operating condition. 1. Turn off the engine by turning the ignition switch OFF. 2. Start the engine. - Check that the 4WD warning light turns off. If the 4WD warning light illuminates, have the system checked by a NISSAN dealer. 3. Apply the parking brake, for automatic transmission vehicles, depress the brake pedal and move the transmission selector to Neutral position. For manual transmission vehicles, move the transmission shift lever to Neutral position. 4. With the brake pedal depressed on automatic transmission vehicles or with the clutch pedal depressed on manual transmission vehicles, move the 4WD shift switch to desired mode. - Be sure to wait until the transfer gear change completes before shifting the transmission selector or transmission shift lever from Neutral position. *2: While changing in and out of 4LO, the ignition key must be ON and the vehicles engine must be running for a shift to take place and for the indicator lights (4WD shift and 4LO position indicator) to be operable. Otherwise, the shift will not take place and no indicator lights will be on or flashing. indicator light (if so equipped) will also turn on when 4LO is selected. See Vehicle dynamic control *3: Make sure the transfer 4LO position indicator light turns on when you shift the 4WD shift switch to 4LO. The system later in this section.

Remove the jack and jacking tools.
All models: 1. Fit the square end of the jack rod into the square hole of the wheel nut wrench to form a handle.

6-4 In case of emergency

2. Find the oval-shaped opening under the middle of the tailgate. Pass the T-shaped end of the jack rod through the opening and direct it toward the spare tire winch, located directly above the spare tire.
4. Once the spare tire is completely lowered, reach under the vehicle, remove the retainer chain, and carefully slide the tire from under the rear of the vehicle.
Be sure to center the spare tire suspending plate on the wheel and then lift the spare tire.
Jacking up vehicle and removing the damaged tire
Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands. Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change. Use the correct jack-up points. Never use any other part of the vehicle for jack support. Never jack up the vehicle more than necessary.

WCE0070

3. Seat the T-shaped end of the jack rod into the T-shaped opening of the spare tire winch. Apply pressure to keep the jack rod engaged in the spare tire winch and turn the jack rod counterclockwise to lower the spare tire.

In case of emergency 6-5

Never use blocks on or under the jack. Do not start or vehicle is on the vehicle to move. for vehicles differentials. run the engine while jack. It may cause the This is especially true with limited slip
Do not allow passengers to stay in the vehicle while it is on the jack. Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move. Always refer to the illustration for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instructions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.

LCE0112

2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. The jack-up points are indicated by stamped arrows on the side of the frame.

WCE0091

Four-wheel drive models
NISSAN recommends that towing dollies be used when towing your vehicle or place the vehicle on a flat bed truck as illustrated.
When towing automatic or manual transmission models with the front wheels on the ground or on towing dollies: Move the 4WD shift switch to the 2H position. Turn the ignition key to the OFF position, and secure the steering wheel in a straight-ahead position with a rope or similar device. Never secure the steering wheel by turning the ignition key to the LOCK position. This may damage the steering lock mechanism.
Never tow automatic transmission models with the rear wheels on the ground or four wheels on the ground, as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the front wheels raised always use towing dollies under the rear wheels.
In case of emergency 6-13
If you have to tow manual transmission models with the rear wheels on the ground (if you do not use towing dollies) or four wheels on the ground: Move the 4WD shift switch to the 2H position. Move the transmission shift lever to the N (Neutral) position. Always release the parking brake. Observe the following restricted towing speeds and distances for manual transmission models only: Speed: Below 60 MPH (97 km/h) Distance: Less than 500 miles (805 km) If the speed or distance must necessarily be greater, remove the propeller shaft before towing to prevent damage to the transmission.

LCE0103

Tow chains or cables must be attached only to the main structural members of the vehicle or the towing hooks (if so equipped). Otherwise, the vehicle body will be damaged. Use the towing hook (if so equipped) only to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle for a long distance using only the towing hook. The towing hook is under tremendous force when used to free a stuck vehicle. Never pull the hook at an angle. Always pull the cable straight out from the front or rear of the vehicle. Pulling devices should be routed so they do not touch any part of the suspension, steering, brake or cooling systems. Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.
VEHICLE RECOVERY (freeing a stuck vehicle)
Stand clear of a stuck vehicle. Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.
6-14 In case of emergency
If your vehicle is stuck in sand, snow, mud, etc., use the following procedure: 1. Turn off the Vehicle Dynamic Control System (if so equipped). 2. Make sure the area in front and behind the vehicle is clear of obstructions. 3. Turn the steering wheel right and left to clear an area around the front tires. 4. Slowly rock the vehicle forward and backward. Shift back and forth between R (Reverse) and D (Drive). Apply the accelerator as little as possible to maintain the rocking motion. Release the accelerator pedal before shifting between R and D. Do not spin the tires above 35 mph (55 km/h). 5. If the vehicle can not be freed after a few tries, contact a professional towing service to remove the vehicle.

WAXING

Regular waxing protects the paint surface and helps retain new vehicle appearance. Polishing is recommended to remove built-up wax residue and to avoid a weathered appearance before re-applying wax. A NISSAN dealer can assist you in choosing the proper product. Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax. Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish. Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks.

REMOVING SPOTS

Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.

WASHING

Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water.

7-2 Appearance and care

UNDERBODY
In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the underbody and suspension. Before the winter period and again in the spring, the underseal must be checked and, if necessary, retreated.

ALUMINUM ALLOY WHEELS

Wash the wheels regularly, especially during winter months in areas where road salt is used. If not removed, road salt can discolor the wheels.
Wipe off excess tire dressing using a dry towel. Make sure the tire dressing is completely removed from the tire tread/grooves. Allow the tire dressing to dry as recommended by tire dressing manufacturer.

CHROME PARTS

Clean all chrome parts regularly with a nonabrasive chrome polish to maintain the finish.
Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.

TIRE DRESSINGS

NISSAN does not recommend the use of tire dressings. Tire manufacturers apply a coating to the tires to help reduce discoloration of the rubber. If a tire dressing is applied to the tires, it may react with the coating and form a compound. This compound may come off the tire while driving and stain the vehicle paint. If you choose to use a tire dressing, take the following precautions: Use a water-based tire dressing. The coating on the tire dissolves more easily with an oil-based tire dressing. Apply a light coat of tire dressing to help prevent it from entering the tire tread/grooves (where it would be difficult to remove).

Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park). Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs. Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position. Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position. Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan.
Maintenance and do-it-yourself 8-5
Windshield washer fluid reservoir Fuse/Fusible link box Air cleaner Engine oil filler cap Engine oil dipstick Brake fluid reservoir/Clutch fluid reservoir (M/T model) 7. Drive belt location 8. Radiator cap 9. Power steering fluid reservoir 10. Battery 11. Engine coolant reservoir
NOTE: Engine cover removed for clarity.
8-6 Maintenance and do-it-yourself
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Windshield washer fluid reservoir Battery Fuse/fusible link box Engine oil filler cap Engine oil dipstick Brake fluid reservoir Air cleaner Drive belt location Radiator cap Power steering fluid reservoir Engine coolant reservoir
Maintenance and do-it-yourself 8-7

ENGINE COOLING SYSTEM

The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round antifreeze and coolant protection.The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary.
Outside temperature down to C -35 F -30
Genuine NISSAN Long Life Antifreeze/ Coolant or equivalent 50%
Demineralized or distilled water
Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down. Serious burns could be caused by high pressure fluid escaping from the radiator. See precautions in If your vehicle overheats found in the In case of emergency section of this manual. The radiator is equipped with a pressure type radiator cap. To prevent engine damage, use only a genuine NISSAN radiator cap.
When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Antifreeze/Coolant (green) or equivalent with the proper mixture ratio of 50% antifreeze and 50% demineralized or distilled water. The use of other types of coolant solutions or coolant colors, such as orange, may damage the engine cooling system.

8-12 Maintenance and do-it-yourself
5-SPEED AUTOMATIC TRANSMISSION FLUID
When checking or replacement is required, we recommend your NISSAN dealer for servicing.

POWER STEERING FLUID

Use only Genuine NISSAN Matic J ATF. Do not mix with other fluids. Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty. The specified automatic transmission fluid is also described on caution labels located in the engine compartment.

WDI0282 LDI0468

Type A The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122 - 176F (50 80C) or using the COLD MAX range on the power steering fluid reservoir at fluid temperatures of 32 - 86F (0 - 30C). If the fluid is below the MIN line, add Genuine NISSAN PSF. Remove the cap and fill through the opening.
DO NOT OVERFILL. Recommended fluid is NISSAN PSF or equivalent. Genuine
Maintenance and do-it-yourself 8-13

BRAKE AND CLUTCH FLUID

For further brake and clutch fluid specification information, refer to Capacities and recommended fuel/lubricants in the Technical and consumer information section of this manual.
Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the brake system and affect the vehicles stopping ability.
Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

LDI0463

BRAKE FLUID
Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer.

CLUTCH FLUID

Check the clutch fluid level in the reservoir (manual transmissions only). If the fluid level is below the MIN line, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer. For further brake and clutch fluid specification information, refer to Capacities and recommended fuel/lubricants in the Technical and consumer information section of this manual.
8-14 Maintenance and do-it-yourself

WINDOW WASHER FLUID

Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent.

Vehicle load capacity. 9-13 Securing the load. 9-15 Utili-track channel system (if so equipped). 9-16 Loading tips. 9-21 Truck-camper loading information. 9-22 Crew Cab Models. 9-22 King Cab models. 9-22 Special Body vehicles. 9-22 Location for center of gravity. 9-22 Vehicle load weight capacity. 9-23 Measurement of weights. 9-25 Towing a trailer. 9-25 Maximum load limits. 9-25 Towing load/specification. 9-29 Towing safety. 9-30 Flat towing. 9-35 Uniform tire quality grading. 9-36 Emission control system warranty. 9-37 Reporting safety defects (US only). 9-37 Readiness for inspection/maintenance (I/M) test. 9-38 Event data recorders. 9-39 Owners Manual/Service Manual order information. 9-39 In the event of a collision. 9-39
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the Maintenance and do-it-yourself section to determine the proper refill capacity.
Fuel Engine oil *8 Drain and Refill With oil filter change Without oil filter change With oil filter change Without oil filter change Cooling system With reservoir Capacity (Approximate) US measure Imp measure 21 1/8gal 17-5/8 gal 5-1/8 qt 4-7/8 qt 5-3/8 qt 5-1/8 qt 4-3/8 qt 4 qt 4-1/2 qt 4-1/4 qt Recommended Fluids and Lubricants Liter 80 4.9 4.6 5.1 4.8 Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1 API Certification Mark *2 *3 API grade SG/SH, Energy Conserving I & II or API grade SJ or SL, Energy Conserving *2 *3 ILSAC grade GF-I, GF-II, or GF-III*2 *3 API Certification Mark *2 *3 API grade SL, Energy Conserving *2 *3 ILSAC grade GF-III*2 *3 50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85 Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85 or 75W-90 Genuine NISSAN Matic J ATF *4 Genuine NISSAN PSF or equivalent.*5 Genuine NISSAN Super Heavy Duty Brake Fluid*6 or equivalent DOT 3 NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a)*7 NISSAN A/C System Oil Type R or equivalent*7 Genuine NISSAN Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid*5, *10 API GL-5 SAE 80W-90 Gear Oil *9, *10 API GL-5 Synthetic 75W-90 Gear Oil, *10 API GL-5 Synthetic 75W-140 Gear Oil, *10 Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze fluid or equivalent

QR25DE VQ40DE

Manual transmission gear oil
QR25DE VQ40DE 5M/T 6 M/T 4XM/T 4X4

Overheating can result in reduced engine power and vehicle speed. The reduced speed may be lower than other traffic, which could increase the chance of a collision. Be especially careful when driving. Pull to the side of the road to a safe area. Allow the engine to cool and return to normal operation. See If your vehicle overheats in the In case of emergency section of this manual.

WTI0160

Tongue load
When using a weight carrying or a weight distributing hitch, keep the tongue load between percent of the total trailer load within the maximum tongue load limits shown in the following Towing Load/Specification chart. If the tongue load becomes excessive, rearrange cargo to allow for proper tongue load.
Vehicle damage resulting from improper towing procedures is not covered by NISSAN warranties.
9-26 Technical and consumer information
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicles maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity. All vehicle and trailer weights can be measured using platform type scales commonly found at truck stops, highway weigh stations, building supply centers or salvage yards. To determine the available payload capacity for tongue load, use the following procedure. 1. Locate the GVWR on the F.M.V.S.S./C.M.V.S.S. certification label. 2. Weigh your vehicle on the scale with all of the passengers and cargo that are normally in the vehicle when towing a trailer. 3. Subtract the actual vehicle weight from the GVWR. The remaining amount is the available maximum tongue load. To determine the available towing capacity, use the following procedure.
1. Find the GCWR for your vehicle on the Towing Load/Specification chart found later in this section. 2. Subtract the actual vehicle weight from the GCWR. The remaining amount is the available maximum towing capacity. To determine the Gross Trailer Weight, weigh your trailer on a scale with all equipment and cargo, that are normally in the trailer when it is towed. Make sure the Gross Trailer Weight is not more than the Gross Trailer Weight Rating shown on the trailer and is not more than the calculated available maximum towing capacity. Also weigh the front and rear axles on the scale to make sure the Front Gross Axle Weight and Rear Gross Axle Weight are not more than Front Gross Axle Weight and Rear Gross Axle Weight on the F.M.V.S.S./C.M.V.S.S. certification label. The cargo in the trailer and vehicle may need to be moved or removed to meet the specified ratings. Example: Gross Vehicle Weight (GVW) as weighed on a scale- including passengers, cargo and hitch - 5,185 lb. (2352 kg). Gross Vehicle Weight Rating (GVWR) from F.M.V.S.S./C.M.V.S.S. certification label 5,815 lb. (2638 kg).

Your vehicle is equipped with a variety of computers that monitor and control a number of systems to optimize performance and help service technicians with diagnosis and repair. Depending on the equipment on your vehicle, some of the computers monitor emission control systems, braking systems, engine systems, transmission systems, tire pressure systems, and airbag systems. Some data about vehicle operation may be stored in the computers for use during servicing. Other data may be stored if a crash event occurs. For example, air bag readiness, air bag performance, and seat belt use by the driver or passenger may be recorded, depending on vehicle equipment. These types of systems are sometimes called Event Data Recorders. Special equipment can be used to access the electronic data that may be stored in the vehicles computers (sounds are not recorded). NISSAN and NISSAN dealers have equipment to access some of this data; others may also have this equipment. The data may be retrieved during routine vehicle servicing or for special research. It might also be accessed with the consent of the vehicle owner or lessee, in response to a request by law enforcement, or as otherwise required or permitted by law.
OWNERS MANUAL/SERVICE MANUAL ORDER INFORMATION
A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illustrations and step-by-step diagnostic and adjustment procedures, this manual is the same one used by the factory-trained technicians working at NISSAN dealerships. Also available are genuine NISSAN Owners Manuals, and genuine NISSAN Service and Owners Manuals for older NISSAN models. For USA For current pricing and availability of genuine NISSAN Service Manuals for the 2000 model year and later contact: Tweddle Litho Company 1-800-450-9491 www.nissan-techinfo.com For current pricing and availability of genuine NISSAN Service Manuals for the 1999 model year and prior, see a NISSAN dealer, or contact: Resolve Corporation 20770 Westwood Road Strongsville, OH 44136 1-800-247-5321 For current pricing and availability of genuine NISSAN Owners Manuals for this model year and prior, see a NISSAN dealer, or contact: Resolve Corporation 20770 Westwood Road Strongsville, OH 44136 1-800-247-5321 For Canada To purchase a copy of a genuine NISSAN Service Manual or Owners Manual please contact your nearest NISSAN dealer. For the phone number and location of a NISSAN dealer in your area call the NISSAN Information Center at 1-800387-0122 and a bilingual NISSAN representative will assist you. Also available are genuine NISSAN Service and Owners Manuals for older NISSAN models.

G Garage door opener, HomeLink Universal Transceiver.2-50 Gas cap.3-10, 3-10 Gauge Engine coolant temperature gauge.2-6 Engine oil pressure gauge.2-8 Fuel gauge.2-7 Odometer.2-4 Speedometer.2-4 Tachometer.2-6 Trip computer.2-5 Trip odometer.2-4 Voltmeter.2-8 General maintenance.8-2 Glove box.2-38 H Hazard warning flasher switch. Head restraints. Active head restraint. Headlight and turn signal switch. Headlight control switch. Headlights. Heated seats. Heater Heater and air conditioner controls Heater operation. Hill descent control (HDC) switch. Hill descent control (HDC) system. Hill start assist (HSA) system. HomeLink Universal Transceiver.2-29.1-6.1-7.2-25.2-25.8-28.2-30.4-2.4-4.2-31.5-32.5-32.2-50
Hood release.3-9 Horn.2-29 I Ignition switch.5-7 Immobilizer system.2-22, 3-2, 5-9 Important vehicle information label.9-10 In-cabin microfilter.8-20 Increasing fuel economy.5-20 Indicator lights and audible reminders (See warning/indicator lights and audible reminders).2-12 Inside automatic anti-glare mirror.3-13 Inside mirror.3-13 Instrument brightness control.2-28 Instrument panel.0-6, 2-2 Instrument panel dimmer switch.2-28 Interior light.2-48 ISOFIX child restraints.1-34 J Jump seat.1-6 Jump starting.6-8 K Key.3-2 Keyfob battery replacement.8-27 Keyless entry system (See remote keyless entry system).3-6
L Labels Air conditioner specification label.9-11 C.M.V.S.S. certification label.9-10 Emission control information label.9-11 Engine serial number.9-10 F.M.V.S.S. certification label.9-10 Vehicle identification number (VIN) plate.9-9 Warning labels (for SRS).1-64 LATCH (Lower Anchors and Tethers for CHildren) System.1-34 License plate Installing the license plate.9-12 Light Air bag warning light.1-64, 2-16 Brake light (See stop light).8-29 Bulb check/instrument panel.2-12 Bulb replacement.8-29 Charge warning light.2-14 Fog light switch.2-28 Headlight and turn signal switch.2-25 Headlight control switch.2-25 Headlights.8-28 Interior light.2-48 Light bulbs.8-28 Low tire pressure warning light.2-15 Low washer fluid warning light.2-16 Passenger air bag and status light.1-58 Personal lights.2-50 Security indicator light.2-19 Warning/indicator lights and audible reminders.2-12 Lights Map lights.2-50
Lock Child safety rear door lock. Door locks. Power door locks. Low fuel warning light. Low tire pressure warning light. Low washer fluid warning light. Luggage rack (see roof rack). Luggage (See vehicle loading information). M Maintenance General maintenance. Inside the vehicle. Maintenance precautions. Outside the vehicle. Seat belt maintenance. Under the hood and vehicle. Malfunction indicator light. Manual front seat adjustment. Manual windows. Map lights. Map pocket. Meters and gauges. Instrument brightness control. Mirror Automatic anti-glare inside mirror. Inside mirror. Outside mirrors. Vanity mirror. Multi-remote control system (See remote keyless entry system).