If the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by a NISSAN dealer. Once the pre-tensioner seat belt has activated, it cannot be reused and must be replaced together with the retractor. See your NISSAN dealer. Removal and installation of the pretensioner seat belt system components should be done by a NISSAN dealer.

CHILD SAFETY

Children need adults to help protect them. They need to be properly restrained. In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations. Every child is different, so be sure to learn the best way to transport your child.
1-12 SafetySeats, seat belts and supplemental restraint system
There are three basic types of child restraint systems: Rear facing child restraint Front facing child restraint Booster seat The proper restraint depends on the childs size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for children who outgrow rear facing child restraints and are at least 1 year old. Booster seats are used to help position a vehicle lap/shoulder belt on a child who can no longer use a front facing child restraint.
for infants and small children. See Child Restraints later in this section. Also, there are other types of child restraints available for larger children for additional protection. NISSAN recommends that all pre-teens and children be restrained in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. This is especially important because your vehicle has a supplemental restraint system (Air bag system) for the front passenger. See Supplemental restraint system later in this section.
placed in a forward facing child restraint. Refer to the manufacturers instructions for minimum and maximum weight and height recommendations. NISSAN recommends that small children be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint that fits your vehicle and always follow the manufacturers instructions for installation and use.

Larger children

Children who are too large for child restraints should be seated and restrained by the seat belts which are provided. The seat belt may not fit properly if the child is less than 4 feet 9 inches (142.5 cm) tall and weighs between 40 lbs (18 kg) and 80 lbs (36 kg). A booster seat should be used to obtain proper seat belt fit. NISSAN recommends that a child be placed in a commercially available booster seat if the shoulder belt in the childs seating position fits close to the face or neck or if the lap portion of the seat belt goes across the abdomen. The booster seat should raise the child so that the shoulder belt is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. A booster seat can only be used in seating positions that have a three-point type seat belt. The booster seat should fit the vehicle seat and

cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. After the pre-tensioner seat belts have activated, load limiters allow the seat belt to release webbing (if necessary) to reduce forces against the chest. If any abnormality occurs in the pre-tensioner system, the supplemental air bag warning light will not come on, will flash intermittently or will turn on for 7 seconds and remain on after the ignition key has been turned to the ON or START position. In this case, the pre-tensioner seat belt may not function properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer. When selling your vehicle, we request that you inform the buyer about the pre-tensioner seat belt system and guide the buyer to the appropriate sections in this Owners Manual.

WRS0169

SRS Air Bag Warning Labels (located on the sun visors) SRS Side Air Bag Warning Labels (located on the door pillar)
SUPPLEMENTAL AIR BAG WARNING LABELS
Warning labels about the supplemental front air bag, supplemental side air bag and curtain sideimpact air bag systems are placed in the vehicle as shown in the illustration.
1-52 SafetySeats, seat belts and supplemental restraint system
When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, supplemental side air bag and curtain side-impact air bag and pretensioner seat belt systems need servicing: The supplemental air bag warning light remains on after approximately 7 seconds. The supplemental air bag warning light flashes intermittently.

LRS0100

If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag, curtain side-impact air bag systems and/or pre-tensioner seat belt systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.
Repair and replacement procedure
The supplemental front air bags, supplemental side air bags, curtain side-impact air bags and pre-tensioner seat belts are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred. Repair and replacement of these supplemental air bag systems should be done only by a NISSAN dealer. When maintenance work is required on the vehicle, the supplemental front air bags, supplemental side air bags, curtain side-impact air bags, pre-tensioner seat belts and related parts should be pointed out to the person performing the maintenance. The ignition key should always be in the LOCK position when working under the hood or inside the vehicle.

Covered storage box. 2-36 Grocery hooks. 2-37 Cargo nets. 2-37 Windows. 2-38 Power windows. 2-38 SkyView glass-paneled roof. 2-40 Sunroof (if so equipped). 2-40 Automatic sunroof. 2-40 Rear sun shade (if so equipped). 2-42 Interior light. 2-43 Personal lights. 2-44 Front. 2-44
Rear. 2-45 Trunk light. 2-45 HomeLink universal transceiver. 2-46 Programming HomeLink. 2-46 Programming HomeLink for Canadian customers. 2-48 Operating the HomeLink universal transceiver. 2-48 Programming trouble-diagnosis. 2-48 Clearing the programmed information. 2-48 Reprogramming a single HomeLink button. 2-48 If your vehicle is stolen. 2-49
2-2 Instruments and controls

METERS AND GAUGES

LIC0989

1. 2. 3. 4. 5. 6.

Tachometer Warning/indicator lights Speedometer Fuel gauge Engine coolant temperature gauge Odometer (total/twin trip)
Instruments and controls 2-3
Resetting the trip odometer:
3 Push the change button for more than 1 second to reset the trip odometer to zero.
Elapsed time, driving distance and average speed information is also available. Refer to Control panel buttons in the Display screen, heater, air conditioner, audio and phone systems section later in this manual.

LIC0990

LIC0991
SPEEDOMETER AND ODOMETER Speedometer
The speedometer indicates the vehicle speed.
Odometer/Twin trip odometer
The odometer/twin trip odometer is displayed when the ignition switch is in the ON position.
1 The odometer records the total distance the vehicle has been driven. 2 The twin trip odometer records the distance of individual trips.

Changing the display

3 Push the change button to change the display as follows:
2-4 Instruments and controls
If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See If your vehicle overheats in the In case of emergency section for immediate action required.

LIC0992 WIC1009

TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm). Do not rev the engine 1 into the red zone.
ENGINE COOLANT TEMPERATURE GAUGE
The gauge indicates the engine coolant temperature. The engine coolant temperature is within the 1 normal range when the gauge needle points within the zone shown in the illustration. The engine coolant temperature varies with the outside air temperature and driving conditions.

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.
If the malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control and/or CVT malfunction. The malfunction indicator light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure
Instruments and controls 2-15
This indicator light will blink when the traction control system is limiting wheel spin. Slippery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly. The slip indicator light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or does not go off, have the traction control system checked by a NISSAN dealer.
tor light while you are driving, have the traction control system checked by a NISSAN dealer. While the traction control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal.
system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the vehicle dynamic control system checked by a NISSAN dealer. While the vehicle dynamic control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal.
Turn signal/hazard indicator lights
The appropriate light flashes when the turn signal switch is activated. Both lights flash when the hazard switch is turned on.
AUDIBLE REMINDERS Brake pad wear warning
The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard.
Traction control system off indicator light (if so equipped)
This indicator light comes on when the traction control off switch is pushed to OFF. This indicates the traction control system is not operating. Push the traction control off switch again or restart the engine and the system will operate normally. See Traction control system (TCS) in the Starting and driving section of this manual. The traction control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the traction control system (TCS) is operational. If the light stays on or comes on along with the SLIP indica-

3-30 Pre-driving checks and adjustments
3. Adjust the drivers seat, steering column, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional information, see Seats in the SafetySeats, seat belts and supplemental restraint system section and Pedal position adjustment and Outside mirrors earlier in this section. During this step, do not turn the ignition to any position other than ON. 4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second. The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds after pushing the switch. After the indicator light goes off, the selected positions are stored in the selected memory (1 or 2). If a new memory is stored in the same memory switch, the previous memory will be deleted.
1. Follow the steps for storing a memory position. 2. While the indicator light for the memory switch being set is illuminated for 5 secbutton on the keyfob. onds, press the The indicator light will blink. After the indicator light goes off, the keyfob is linked to that memory setting. With the key removed from the ignition switch, button on the keyfob. The drivpress the ers seat and outside mirrors will move to the memorized position. NOTE: If a new memory position is saved to the memory switch, the keyfob automatically re-links.
3. Push the memory switch 1 or 2 fully for at least 1 second to operate the automatic drive positioner. 4. Turn the outside mirror control switch to L (left). 5. Depress the brake pedal. 6. Move the CVT selector lever to R (Reverse). 7. Adjust the mirror to the desired viewing position for backing up by operating the outside mirror control switch. 8. Push the SET switch and, within 5 seconds, push the memory switch 1 or 2 selected in step 3 fully for at least 1 second. The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds after pushing the switch. After the indicator light goes off, the selected mirror position is stored in the selected memory (1 or 2). 9. Turn the outside mirror control switch to R (right). Repeat the above procedure to adjust the right mirror position and store in the selected memory. When the drivers seat, accelerator and brake pedals, and outside mirrors are not in the memorized position, the outside mirror will move with the initial tilt-down angle.
Procedure for storing the outside mirror positions for best visibility when backing up
An outside mirror position for backing up can be stored for each memory switch (1 and 2). 1. Set the parking brake. 2. Turn the ignition ON. (Do not start the engine.)

Display screen, heater, air conditioner, audio and phone systems 4-47
4. The system announces the current language and gives you the option to change the language to Spanish (in Spanish) or French (in French). Use the following chart to select the language. NOTE: Note: You must press the button or the button within 5 seconds to change the language.
Current language English Spanish French Press (PHONE/SEND) to select Spanish English English Press (PHONE/END) to select French French Spanish
5. If you decide not to change the language, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed.
C 4. Say: New phone. The system acknowledges the command and asks you to initiate D pairing from the phone handset.

Pairing procedure

NOTE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled.
Main Menu A Setup B Pair Phone C New Phone D Initiate from handset E Name phone F Assign priority G Choose ringtone
The pairing procedure of the cellular phone varies according to each cellular phone manufacturer. See the cellular phone Owners Manual for details. You can also visit www.nissan-usa.com/bluetooth for instructions on pairing NISSAN recommended cellular phones. When prompted for a PIN code, enter 1234 from the handset. The PIN code 1234 has been assigned by NISSAN and cannot be changed. 5. The system asks you to say a name for the E phone. If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if more than one phone is paired and the name sounds too much like a name already used, the system tells you, then prompts you for a name again.
1. Press the button on the steering wheel. The system announces the available commands.
A 2. Say: Setup. The system acknowledges the command and announces the next set of available commands. B 3. Say: Pair phone. The system acknowledges the command and announces the next set of available commands.
4-48 Display screen, heater, air conditioner, audio and phone systems
6. The system asks you to assign a priority level F. The priority level determines which phone is active when more than one paired Bluetooth phone is in the vehicle. Follow the instructions provided by the system or refer to Setup later in this section for more information on changing priorities. 7. The system will ask if you would like to select G a custom ring tone. Follow the instructions provided by the system or refer to Setup later in this section for more information on selecting ringtones.

B Number (speak digits)

The system acknowledges the command, repeats the number and begins dialing. If a call back number does not exist, the system announces, There is no number to call back and ends the VR session. During a call During a call there are several command options button on the steering available. Press the wheel to mute the receiving voice and enter commands. Help The system announces the available commands. Go back/Correction The system announces Go back, ends the VR session and returns to the call. Cancel/Quit The system announces Cancel, ends the VR session and returns to the call. Send/Enter/Call/Dial Use the Send command to enter numbers during a call. For example, if you were directed to dial an extension by an automated system: Say: Send one two three four. The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR ses-

Main Menu Call

When prompted by the system, say the number you wish to call. Refer to How to say numbers and Making a call by entering a phone number earlier in this section for more details.

C Redial

A Name (speak name) B Number (speak digits) C Redial D Call Back
Use the Redial command to call the last number that was dialed within the vehicle. NOTE: The system will not redial the last number dialed by the handset keypad. The system acknowledges the command, repeats the number and begins dialing. If a redial number does not exist, the system announces, There is no number to redial and ends the VR session.

D Call back

A Name (speak name)
If you have stored entries in the Phone Book, you can dial a number associated with a name and location. See Phone book later in this section to learn how to store entries. When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name.
Use the Call Back command to dial the number of the last incoming call within the vehicle.
4-50 Display screen, heater, air conditioner, audio and phone systems
sion and returns to the call. Transfer call Use the Transfer Call command to transfer the call from the Bluetooth Hands-Free Phone System to the cellular phone when privacy is desired. The system announces, Transfer call. Call transferred to privacy mode. The system then ends the VR session. You can also issue the Transfer Call command again to return to a hands-free call through the vehicle. Mute Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.

Use the Select Ringtone command to select the tone heard in the vehicle when an incoming call is received. The system announces the name of the active phone and asks you to choose from the following commands: Ringtone The system plays a ringtone and asks if you would like to select that tone. If you say no, the system plays the next ringtone available and continues to cycle through the ringtones until you select one or quit. Silent The system asks you to confirm your wish to disable the ringtone.
Use the Delete Phone command to delete a specific phone or all phones from the Bluetooth Hands-Free Phone System.

Training procedure

The procedure for training a voice is as follows.
4-54 Display screen, heater, air conditioner, audio and phone systems
1. Position the vehicle in a reasonably quiet outdoor location. 2. Sit in the drivers seat with the engine running, the parking brake on, and the transmission in P (Park). 3. Press and hold the than 5 seconds. button for more
9. When training is finished, the system will tell you an adequate number of phrases have been recorded. 10. The system will ask you to say your name. Follow the instructions to register your name. 11. The system will announce that speaker adaptation has been completed and the system is ready. The SA mode will stop if: button is pressed for more than 5 The seconds in SA mode. The vehicle begins moving during SA mode. The ignition switch is turned to the OFF or LOCK position.
eight pause nine three two pause seven delete all entries call seven two four zero nine phone book delete entry memo pad record dial star two one seven oh Yes No select ring tone dial eight five six nine two Bluetooth on setup change priority call three one nine oh two nine seven pause pause three oh eight Cancel call back number call star two zero nine five delete phone dial eight three zero five one Home
4. The system announces: Press the ) button for the PHONE/SEND ( hands-free phone system to enter the speaker adaptation mode or press the PHONE/END ( ) button to select a different language. 5. Press the button. For information on selecting a different language, see Choosing a language earlier in this section. 6. Voice memory A or memory B is selected automatically. If both memory locations are already in use, the system will prompt you to overwrite one. Follow the instructions provided by the system. 7. When preparation is complete and you are ready to begin, the press the button. 8. The SA mode will be explained. Follow the instructions provided by the system.

CRUISE CONTROL OPERATIONS
The cruise control allows driving at a speed between 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The CRUISE indicator light in the instrument panel comes on.
5-14 Starting and driving
To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previously set speed. The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. To cancel the preset speed, use one of the following three methods. Push the CANCEL button; the SET indicator light in the instrument panel goes out. Tap the brake pedal; the SET indicator light goes out. Turn the main switch off. Both the CRUISE indicator light and SET indicator light in the instrument panel go out. The cruise control is automatically canceled and the SET light in the instrument panel goes out if: you depress the brake pedal while pushing the ACCEL/RES or SET/COAST switch. The preset speed is deleted from memory.
the vehicle slows down more than 8 MPH (13 km/h) below the set speed. you move the shift selector lever to N (Neutral). To reset at a faster cruising speed, use one of the following three methods. Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch. Push and hold the ACCEL/RES switch. When the vehicle attains the speed you desire, release the switch. Push and release the ACCEL/RES switch. Each time you do this, the set speed increases by about 1 MPH (1.6 km/h). To reset at a slower cruising speed, use one of the following three methods. Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it. Push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed. Push and release the COAST/SET switch. Each time you do this, the set speed decreases by about 1 MPH (1.6 km/h).
To resume the preset speed, push and release the ACCEL/RES switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).

If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

CHANGING A FLAT TIRE

If you have a flat tire, follow the instructions below.

Stopping the vehicle

1. Safely move the vehicle off the road and away from traffic. 2. Turn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake. Move the shift selector lever to P (Park). 4. Turn off the engine. 5. Raise the hood to warn other traffic and to signal professional road assistance personnel that you need assistance. 6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.

6-2 In case of emergency

Make sure the parking brake is securely applied and the CVT is shifted into P (Park). Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance.

WCE0044

LCE0074

Blocking wheels

1 Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire 2 to prevent the vehicle from moving when it is jacked up.
Getting the spare tire and tools
Open the trunk. Lift the trunk floor carpeting and 1 spare tire cover. Remove the jack and wheel 2 nut wrench from the tool box. Remove the spare tire.
Be sure to block the wheel as the vehicle may move and result in personal injury.

In case of emergency 6-3

LCE0075

LCE0076

CE1089
Jacking up vehicle and removing the damaged tire
Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands. Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change.

Do not wash the vehicle with strong household soap, strong chemical detergents, gasoline or solvents. Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted. Avoid using tight-napped or rough cloths, such as washing mitts. Care must be taken when removing caked-on dirt or other foreign substances so the paint surface is not scratched or damaged. Rinse the vehicle thoroughly with plenty of clean water. Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots.

WAXING

Regular waxing protects the paint surface and helps retain new vehicle appearance. Polishing is recommended to remove built-up wax residue and to avoid a weathered appearance before re-applying wax. A NISSAN dealer can assist you in choosing the proper product. Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax. Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish. Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks.

REMOVING SPOTS

Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.

WASHING

Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water.

7-2 Appearance and care

UNDERBODY
In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the underbody and suspension. Before the winter period and again in the spring, the underseal must be checked and, if necessary, retreated.
Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.
When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements.

Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down. Avoid contact with used engine oil and coolant. Improperly disposed engine oil, engine coolant and/or other vehicle fluids can damage the environment. Always conform to local regulations for disposal of vehicle fluid. This Maintenance and do-it-yourself section gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN service manual is also available. See Owners Manual/Service Manual order information in the Technical and consumer information section of this manual. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer.
Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park). Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs. Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position. Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position. Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan.
Maintenance and do-it-yourself 8-5
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Power steering fluid reservoir Engine oil filler cap Brake fluid reservoir Air cleaner Battery Fuse/Fusible link box Engine oil dipstick Radiator cap Drive belt location Fuse block Windshield washer fluid reservoir Engine coolant reservoir
NOTE: Engine cover removed for clarity.
8-6 Maintenance and do-it-yourself

RECOMMENDED SAE VISCOSITY NUMBER
SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0F (-18C).
9-6 Technical and consumer information

SPECIFICATIONS ENGINE

Model Type Cylinder arrangement Bore x Stroke Displacement Firing order Idle speed CVT (in N position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle Spark plug Spark plug gap (Nominal) Camshaft operation DILFR5A11 in (mm) 0.043 (1.1) Timing chain No adjustment is necessary. VQ35DE Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60 in (mm) 3.760 x 3.205 (95.5 x 81.4) cu in (cm3) 213.45 (3,498) 123456
The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Technical and consumer information 9-7
Wheels 17 x 7JJ 18 x 7.5JJ Tires P225/55R17 95V P245/45R18 96V Spare tire Temporary Full size Speed rating *: R or D depending on tire manufacturer T145/80*or 18 H V

DIMENSIONS AND WEIGHTS

Overall length Overall width Overall height Front tread 17 inch tire 18 inch tire Rear tread 17 inch tire 18 inch tire Wheelbase Gross vehicle weight rating Gross axle weight rating Front Rear in (mm) in (mm) lb (kg) 61.6(1,565) 61.2(1,554) in (mm) in (mm) 61.4(1,560) 61.0(1,549) in (mm) 193.5(4,915) in (mm) in (mm) 71.7(1,821) 58.3(1,480)
in (mm) 111.2(2,824) See the F.M.V.S.S./C.M. V.S.S. certification label on the center pillar belb (kg) tween the drivers side front and rear doors. lb (kg)
9-8 Technical and consumer information
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY
When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicles engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ. When any vehicle is to be taken into another country, state, province or district and registered, its modifications, transportation, and registration are the responsibility of the user. NISSAN is not responsible for any inconvenience that may result.