Communicator applications
The coloured application buttons on the communicator keyboard are used to start the corresponding applications. Telephone Used for managing voice calls. Fax Enables you to send any of your own documents as a fax. Received faxes can be read or forwarded. SMS Enables you to send short messages. Received short messages can be read, replied, or forwarded. Internet Includes Internet and modem-based applications. Contacts Used for managing contact information, such as names, numbers and addresses. You can exchange contact information as business cards via the SMS application. Notes Used for writing and storing documents.
Calendar Contains an appointment book and a to-do list. You can book events in other calendars and set alarms to events. System Contains PC connectivity, security and other system-related applications. Extras ( ) Includes various items, such as Calculator, Clock, and Composer.

To use the applications

When the cover is opened, the application that was on the display when you closed the cover, appears in the same state. However, if you have made or answered a voice call via the phone and switch to the communicator interface by opening the cover, the Telephone application starts automatically. To switch to another application, press the corresponding application button. You can do this even during a call. Majority of the applications can be opened and used simultaneously with other applications. For example, you can write a note or a new calendar event during a voice call. All inactive applications remain in the background until you start them again. To send or receive calls or messages with any of the communications applications, remember that the phone must be switched on and in a service area with adequate cellular signal strength. Note: Information needs not be specifically saved. When you press Close, switch to another application, or close the device cover, the Nokia 9110i Communicator saves all data.

Connectors

The Nokia 9110i can be connected to a variety of devices. The connectors are (figure 10):
Figure IrDA-SIR infrared port for connecting to a PC, a printer, a digital camera, or another communicator. For information on infrared connection, see chapter 4 "Computer connectivity" on page 35. 2 Connector for the charger plug. 3 Connector for the RS-232 cable plug and the headset plug.

Use the battery only for its intended purpose. Never use any charger or battery which is damaged or worn out. Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or pen) causes direct connection of the + and terminals of the battery (metal strips at the bottom of the battery), for example, when you carry a spare battery in your pocket or purse. Shortcircuiting the terminals may damage the battery or the connecting object. Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between +15C (+59F) and +25C (+77F). A communicator with a hot or cold battery may temporarily not work, even when the battery is fully charged. The performance of Lithium-ion batteries is particularly limited in temperatures below 0C (+32F). Do not dispose of batteries in a fire! Batteries must be recycled or disposed of properly. Batteries must not be disposed of in municipal waste. Copyright 2004 Nokia. All rights reserved.

3. Special features

This chapter explains functions that are common to most of the applications. Communicator features on page 27 goes through various features of the device, and Document features on page 30 explains functions that apply to writing and viewing of documents.

Communicator features

Figure 1

To use the Menu button

1 Press the button on the left of the communicator display to open up a set of options which depend on the application you are in. 2 Move the selection frame over the desired option and press Select. The chosen option affects only the document, card or item that is currently selected, open, or being sent. The Menu may also contain the option Settings with which you can change the settings of the application. The values of these settings will be used as defaults for that application.

To use the Zoom button

Press the button on the left of the display to magnify the view on the display. Zooming is not available on every occasion.
To use the Backlight button
Press the button on the left of the display to turn the backlight of the communicator display on and off. The backlight can be adjusted in the System settings. See System settings on page 115.

To use the Help button

Press the button on the communicator keyboard to open up a help text on the current function. The application icon in the indicator area on the left side of the display reminds you of the application where you requested help. The help deals with issues relating to the item that was on the display when you pressed the Help button. If no special help is available for the current item, a list of available help topics is shown instead. To view the list of all help topics for the current application, press Application help. The following commands become available: Open Opens the selected topic. General help Shows the common help topics. Close Closes the help. To view the list of general communicator topics, press General help. The following commands become available: Open Opens the selected topic. Application help Returns to the help topics list of the current item. Close Closes the help. If the help topic you wanted was not among the help topics of the current item or in the general help, close the help, start the correct application and press the Help button again.

To use the memory card

A memory card may contain documents, contact databases, applications, backups, printer drivers, etc. When a memory card is inserted in the communicator, the memory card contents are marked with the memory card icon in the corresponding applications. For example, the documents on the memory card are located in a folder shown in the folders list of the Notes application. The items on the memory card can be used in the same way as corresponding items in the communicator. You can for example install and remove software to and from the memory card with the Install/Remove software application, and send messages to contacts in the contacts directory of the memory card.
To insert the memory card
1 Close the device cover and make sure that the phone is switched off. If it is on, press. 2 Remove the battery: press the catch at the top of the battery and lift the battery away from the battery cavity. 3 Open the hatch at the back of the communicator: carefully open the lid by easing it up from the ridges on both sides.
4 Slide the memory card under the memory card holder. Make sure that the gold contacts of the card are facing down and that the bevelled corner of the card is on the right. See figure 2.
Figure When the card is securely in place, close the hatch, and replace the battery. IMPORTANT! Keep all memory cards out of small childrens reach. Make sure that the hatch is closed before replacing the battery! Do not remove the memory card in the middle of an operation. Be sure to close all memory card applications before removing the card. If you are installing an application to the memory card and you need to reboot the communicator, do not remove the card until the reboot is complete. Otherwise the application files may be lost. If you have an application on both the memory card and the communicator, the one in the communicator is used.

To select several items

Where multiselection is available, you can select several items at once. The commands you use affect all the selected items. Multiselection works in most lists. For example, you can select several contacts and remove them at once in the Contacts directory, or select several documents and copy them to a memory card at the same time in the Notes application. There are two ways to select several items: 1 Scroll to the item and press Ctrl-space bar. Or, 2 Press and hold Shift and move up or down the list with the arrow keys to the last selected item. To remove an item from the selection, scroll to the item and press Ctrl-space bar again. To cancel the entire selection, press Chr-Q. If you want to select every item in a list, press Ctrl-A. If you want to cancel the selection, press Ctrl-A again.

Document features

To name a document
Every time you close a new document for the first time, you will be asked to enter a name for the document in the input field. The highlighted name in the input field is the communicators suggestion for the name.

To install the Nokia Communicator Server on a PC
1 Insert the diskette into the diskette drive. 2 In the Windows Program Manager, click on the File menu. 3 Click on menu item Run and type a:\server in the command line. Substitute the letter a with the letter of the diskette drive. 4 Press Enter. 5 Follow the instructions shown on the screen. Copyright 2004 Nokia. All rights reserved.
To use the Nokia Communicator Server with an infrared connection
1 Follow the first two steps for installing the PC Suite. 2 Start the Nokia Communicator Server software on the PC. 3 Start the desired PC connectivity application on your communicator. Remember to set infrared as the connection type.
To use the Nokia Communicator Server with a cable connection
1 Connect the 9-pin end of the RS-232 adapter cable DLR-2 to the COM port of the PC, and the other end to the connector at the bottom of the communicator. See Connectors on page 24. 2 Start the Nokia Communicator Server software on the PC. Check that the COM port reported by the software is correct. 3 Start the desired PC connectivity application on your communicator. Remember to set cable as the connection type. Tip: For information on how to install new software on your communicator with the Nokia Communicator Server, see Install/ Remove software on page 125.
Nokia Communicator Server for MacOs
To connect to an Apple Macintosh, you must have the Nokia Communicator Server application running on the Macintosh and a cable connection established between the communicator and the Macintosh. The Nokia Communicator Server application is compatible with MacOS 7.5 or newer versions, provided that they are equipped with a RS-422 serial port. Macs equipped with a USB port can be connected to a communicator using a USB to serial adapter. To connect to an Apple Macintosh RS-422 serial port, you need to have an Apple Mac modem cable (not provided by Nokia) connected to your Mac. To connect the modem cable to the DLR-2 cable (included in the sales package), you need to have an 9M25F adapter (not provided by Nokia), because the Mac modem cable has 25 pins and the DLR-2 RS cable has only 9 pins. With this cable combination you can use the Nokia Communicator Server software for MacOs. The PC suite connectivity software does not support MacOS.

5. Contacts

The Contacts application is used for creating, editing, and managing all contact information, such as phone numbers, addresses and speed dials, and for viewing logs of all incoming and outgoing voice, data and fax calls and SMS messages. The Telephone, Fax, SMS, Calendar and Mail applications all use information found in the Contacts directory. Tip: You will find the Club Nokia Careline contact card in the Contacts directory. You can visit http://club.nokia.com to find the Club Nokia Careline phone numbers. See also Accessories guide for further information on Club Nokia Careline.

Contacts directory

The Contacts main view shows two windows: on the left is the Contacts directory, which is a list of all contact cards, and on the right is the currently selected contact card. The active window is surrounded by a dark frame. You can toggle between the windows with the Tab key. The contact cards are listed in the Contacts directory in alphabetical order according to the name in the Name field of each card.

To find contact cards

1 Move the selection frame in the Contacts directory with the arrow keys until the contact you are searching for is shown within the selection frame. Or, Copyright 2004 Nokia. All rights reserved.
2 Enter text into the search field. The search looks for matches in the Name, Company and Address fields. The search results can be cleared by removing characters one by one from the search field with the backspace key. To open the selected contact card, press Open. To remove the selected contact card, press Delete. Note: If you have a memory card inserted in the communicator, the memory card contact databases are shown as folders in the Contacts main view. When you open a folder, only the contact information stored in that database is available for use.
Pressing the Menu button in the Contacts directory opens a new set of options: Individual log Opens the Individual log of the selected contact, see Logs on page 51. General log Opens the General log. Duplicate card Creates a duplicate of the selected card. SIM card memory Shows the contents of your SIM card. Copy to SIM Copies the selected contact(s) to the SIM card memory. Create group Creates a new contact group, see Contact groups on page 50. List groups Opens a list of all contact groups. New contacts database Creates a new contacts database to the memory card. Rename contacts database You can give the memory card contacts database a new name. Copy contacts You can copy contacts to and from your memory card. Move contacts You can move contacts to and from your memory card. Contact info Shows the number of contacts and the amount of contact data. Settings Enables you to change the following settings: Contact card template You can define which fields are included in all new contact cards you create. Changes made to the template affect all new, but not existing contact cards. You cannot enter text into the fields of the template. Log length You can define how recent contacts will be listed in the General and Individual logs. Select the new log length and press OK. The possible values are: Zero / 10 days / 30 days / 1 year / User defined: days (days). Copyright 2004 Nokia. All rights reserved.

To forward a received fax
1 Select the Received faxes folder in the Fax main view and press Open. 2 Select a fax and press Open. 3 Press Forward to access the Fax directory. Copyright 2004 Nokia. All rights reserved.
Tip: Forward options allows you to select the specific pages you want to send: All, This page, or Pages. Choose Pages to enter the page numbers, first through last, e.g. 3-5, that you want to forward.

To select a recipient

1 Select a contact in the Fax directory and press Select. See figure 1. The names of contacts who have no fax number are dimmed and cannot be selected. 2 If the selected contact has several fax numbers, a pop-up box opens. Choose a number from the list and press Select.
Figure 1 If there is no contact card in the Contacts directory for the recipient to whom you are sending the fax, press Enter number to enter the fax number manually, or obtain the information from the Recent numbers list by pressing Recent numbers. The list contains the fax numbers with which you have recently had contact. Choose a number and press Select. Tip: If you press Clear both lists in the Recent numbers view, all information in the lists is removed. When you open one of the lists and select a contact, Create card enables you to create a contact card for the contact.
Fax cover page and send options
The fax cover page contains three fields, see figure 2. You can edit the entries in all the cover page fields. The From field is always filled automatically according to the User data card in the System application. See User data on page 120. To adjust the fax sending options, press Send options. The send options are: Cover page, Send resolution, Logo file, Signature file, Begin sending, Resend, and ECM. For more information, see Fax settings on page 68. To change an option, select it and press Change. Copyright 2004 Nokia. All rights reserved.
Figure 2 To send the fax, press Send. The fax is handed over to the Document outbox, which will send the fax as soon as possible. Note: In case the sending fails, be sure to save all your important faxes.

To receive faxes

Faxes are received automatically, provided that this service is available and that the phone is on and within cellular coverage. All received faxes go to the Received faxes folder. If you do not wish to receive the fax, close the cover and press. When a new fax has been received, you will hear a tone - unless the system is set to a silent profile - and an information note is shown on the display.

To read a received fax

To create new or edit existing connections, press Define. To change the settings for incoming data calls, press Settings, select the setting and press Change. The available settings are: Local echo for incoming data call If set to On, characters typed from the communicator keyboard are echoed locally to the communicator. If set to Off, they are echoed to the remote host computer. Line end for incoming data call Defines which character is generated with the Enter key in incoming data. The alternatives are: Carriage return (CR), Linefeed (LF), and Carriage return - Linefeed (CR/LF)
To define Terminal connections
After you have pressed Define in the Terminal main view, the defined Terminal connections are shown. To remove the selected connection, press Delete. To edit existing connections, press Edit, or press New to define new Terminal connections. The following settings become available:
Figure 9 Connection name Write the name of the connection. The name can be defined freely. Phone number The phone number for accessing the service. The phone number may include spaces and hyphens. Data bits: 7/8 Service/host-specific communication parameter. Parity: None /Odd/Even Service/host-specific communication parameter. Stop bits: 1 /2 Service/host-specific communication parameter. Local echo: On/Off If set to On, characters typed from the communicator keyboard are echoed locally to the communicator. If set to Off, they are echoed to the remote host computer. Modem initialisation Enter here a modem initialisation string containing AT commands, if needed. This initialisation string is executed after the string you define in the Modem initialisation: Custom option of the Internet settings. Backspace key: BS/DEL Defines whether the keyboard backspace key is used as a backspace or delete key. Line end Defines which character is generated with the Enter key in the terminal session. The alternatives are: Carriage return (CR), Linefeed (LF), and Carriage return - Linefeed (CR/LF). Copyright 2004 Nokia. All rights reserved.

Terminal connection

When you have connected to the remote system, the following commands become available: Press Keys to emulate the VT100 special keys, which are not available on the communicator keyboard. The special keys include: All VT100 application keypad keys: numbers 1-9, hyphen, comma, period, enter. The following VT100 functions: reset terminal, Ctrl-\, Ctrl-], Ctrl-~, Ctrl-?. The selected special character is entered to the left of the cursor by pressing Insert. The arrow keys can be used for scrolling the view. Scrolling does not affect the cursor position. Pressing any keyboard key returns the view to the cursor position. Press Hang up to close the connection to the host, end the data call and return to the Terminal main view.

When you press the Menu button in the monthly, daily and weekly schedules, the following options become available: To-do list Opens the To-do list. Available in the daily schedule only. Pending requests Opens the list of pending calendar event requests. Today Shows the current day. Next month/week/day (Ctrl-N) Shows the next month, week or day. Copyright 2004 Nokia. All rights reserved.
Previous month/week/day (Ctrl-P) Shows the previous month, week or day. Settings Enables you to change the following options: Booking password You can set a password to protect your calendar from receiving reservations from anyone except those who have your password. The maximum length of the password is 8 characters. When a password is written in the field, all characters appear as asterisks. Default alarm When you set an alarm to an event, the alarm will go off 10 minutes before the scheduled time of the event, unless you specify otherwise here. Beginning of week You can select which day is considered to be the first day of the week.

Calendar booking

Calendar booking enables you to send event requests or reservations to other communicators or calendar servers. The difference between an event request and an event reservation is that the recipient may decide whether to accept or discard an event request, but event reservations can only be accepted.

Booking password

Sending event reservations requires that you know the recipients booking password. If you add the recipients password to the booking password field of the recipients contact card, the password is automatically taken from there when you send a reservation. When you send a reservation with an incorrect password, the recipients communicator discards the reservation. You can give your own booking password to those whom you allow to send reservations to your calendar. If you do not set a password, your communicator accepts all reservations. Define your booking password in the Calendar settings. Note: The recipients booking password is not needed when you send event requests.
To make requests and reservations
Select an event in the daily schedule or write a new one. Press Calendar booking in the Details view. Select whether to send the event as a request or a reservation. Press Transfer via IR to send the booking to another Nokia 9110 or 9110i Communicator via the infrared link, or press Send as SMS to open the SMS directory where you can select the recipient for the booking. Note Copyright 2004 Nokia. All rights reserved.

1 Press Details in the daily schedule. 2 Select the Alarm option and press Change. 3 Select one of the alarm options: None No alarm is attached to the event. At start time The alarm will sound at the start time. minutes before event The alarm will go off as set in the Calendar settings unless you specify otherwise here. Tip: To set alarms that are not related to any calendar event, use the Clock application, see Clock on page 128. You can choose the alarm tone in the System sounds settings of the System application. An active alarm is indicated by the bell icon in the daily schedule (in the figure 3, the 11:00 event). When the alarm sounds, a note is shown on both displays. The alarm sound can be turned off by pressing any key. If you have set the communicator to a silent profile in the Telephone settings, only the alarm note will be shown. Tip: After a calendar alarm has occurred, you can move the message contents of the alarm to the To-do list by pressing Move to To-do list.

To-do list

The To-do list is a list of tasks which must be completed eventually, but are not connected to any specific time or day. The entries in the To-do list are numbered, and they can be given different statuses. High priority entries are shown at the top of the list. See figure 5.

To access the To-do list

1 Press the To-do list command button in the monthly or weekly schedule. Or, 2 Press the Menu button and select the To-do list option in the daily schedule.
To change the status of the selected task
1 Press Priority. A pop-up box opens. 2 Change the status of the entry to High priority or Normal priority, or mark the task as Completed, as the task number four in figure 5. To write down a new to-do task, press New. An empty entry field is added at the end of the To-do list. To remove the currently selected task from the list, press Delete.

12. System

System contains the following applications: Security, User data, Memory, Infrared activation, Digital camera connectivity, Remote synchronisation, Fax modem, Data removal, Install/Remove software, Backup/Restore, Memory card tool, and About this product.
To start a System application
1 Press the System application button. 2 Scroll to the application and press Select. 3 If a System application is active, you must close it by pressing Close in the main view of the application before you can start another. Note: When one of the PC connectivity applications or the fax modem is in use, the communicator consumes more power than normally. To extend the battery operation time, these applications should be closed when they are not used.

MENU 2

CALL REGISTER PROFILES SETTINGS CALL DIVERT RECORDER

MENU 3 MENU 4

MENU 5 MENU 6
Some menu functions are network services, indicated by the symbol in the menu table. To use such a function, your network must support it and you must subscribe to it. Note that network services are specific to each SIM card. If you change the SIM card, and you have not obtained the service for the new card, you will not be able to use the service.

Messages (Menu 1)

The Short Message Service (SMS) is a network service. Contact your service provider for details. The phone can be used for listening to voice messages in voice mailboxes and for reading received short messages. However, reading short messages is more convenient via the larger display of the communicator interface. To send short messages, use the SMS application of the communicator.
Received short messages (Menu 1-1)
When you receive a short message, the text Message received and the indicator will be displayed and a tone will sound, unless the communicator is set to a silent profile. A note is also shown when you receive faxes or mail. To read received faxes or mail, you must use the respective applications of the communicator interface. 1 To read the message immediately, press Read. To read the message later, press Exit. 2 Press Read again to view the received message. The messages are listed in the order they were received. To read the second message on the list, press to select it and then press Read. Once you have read the message, you can press Back or Option. The options available in the phone are: Erase Erases the selected message from the memory. Use number Copies the phone number from the message and moves it onto the phone display. You can now call the number with. Details Shows the senders name or number, the date and time the message was sent, and the number of the message centre. Tip: You can dial the phone number in the message by pressing while viewing the message.

Info service (Menu 1-2)

Phone settings (Menu 4-2)
Clock (Menu 4-2-1) You can select whether the time is shown on the display. Cell info display (Menu 4-2-2) When this function is set on, the phone will indicate when it is using a network cell based on Micro-Cellular Network technology. The setting will remain in effect even if the SIM card is changed or the phone is switched off. Note: The communicator consumes more power when the Cell info display is on. Name list (Menu 4-2-3) When searching for names and numbers, you can select whether to show three names, or one name at a time on the display. List of own numbers (Menu 4-2-4) You can store and manage phone numbers assigned to your SIM card. This function is a memory aid, from which you can check your own phone numbers. Welcome note (Menu 4-2-5) You can write a message of up to 36 characters which appears on the display when you switch on the phone. Copyright 2004 Nokia. All rights reserved.
1 Scroll to the Welcome note setting and press Select. 2 Key in the message. 3 Press Options and scroll to Save and press OK. Network selection (Menu 4-2-6) The communicator can be set to select automatically one of the cellular networks available in your area. You may also select the desired network manually in this menu. When the Automatic option is selected, the communicator tries to utilise the network on which it was last registered. Outside of the home network service area, the communicator will select one of the networks that have a roaming agreement with the home network. In the Manual mode, when you pick up a network manually from the network list, the communicator will always attempt to register on that network. If the communicator cannot reach, or loses contact with, the selected network, you are prompted to select another network. Tip: Network selection comes in handy when you want to select a particular network, e.g. due to lower call charges.
Security settings (Menu 4-3)
The purpose of the security system is to prevent unauthorised use or altering of important settings. In most cases, activating or changing the security options requires the appropriate access code. See Security on page 117. Note: When security features which restrict calls are in use (call diverting, call barring, fixed dialling, closed user group, or system lock), calls may be possible to certain emergency numbers in some networks (e.g. 112 or other official emergency number). PIN code request (Menu 4-3-1) On or Off. See Security on page 117. Voice call barring (Menu 4-3-2) Call barring is a network service; contact your operator for subscription. See Telephone settings on page 58. 1 Scroll to one of the following barring modes and press Select. All outgoing calls Copyright 2004 Nokia. All rights reserved.
All international calls International except to home country All incoming calls Incoming calls when abroad Cancel all barrings 2 If you want to take the selected barring mode into use, scroll to Activate; if you want to disable the selected barring mode, select Cancel, or if you want to check the status of the barring mode, select Status, and press OK. Fixed dialling (Menu 4-3-3) You may restrict your outgoing calls to a pre-determined set of phone numbers, if supported by your SIM card. When the function is set on, you can only call a phone number which is included in the fixed dialling list or which begins with the same digits as a phone number on the list. You are prompted for the PIN2 code when you try to put Fixed dialling on or off, or if you wish to delete, add or edit any phone number on the fixed dialling list. If you select Numbers, the following options become available: Search, Add entry or Erase all. If you select Add entry, you are required to enter your PIN2 code and key in both the name and number you wish to add to the fixed dialling list. To edit or erase a phone number on the fixed dialling list, select Search and key in the name of the person , or the first letter(s) of the name. Press OK and Detail to view the number. Select Options, enter your PIN2 code and you are given the choice of either Edit and Erase. Note: The SIM card contents cannot be accessed if the Fixed dialling is on. Closed user group (Menu 4-3-4) This network service allows you to set the communicator to accept calls to and from a selected group of people. For details on creating a user group and activating this service, contact your network operator. You may be a member of up to 10 user groups. Select one of the following options: Preset Uses a user group that the SIM card owner has agreed upon with the network operator. On Uses a particular user group. Calls can be made to or received from the members of the selected group only. Off Calls can be made and received in the normal way. You can use this option only if you are entitled to do so. Copyright 2004 Nokia. All rights reserved.

SIM change security (Menu 4-3-5) The same settings can be found in the Security settings. See Security on page 117. Change access codes (Menu 4-3-6) In this submenu, you can change the lock code, the PIN code, the PIN2 code and the barring password. See Security on page 117. The access codes may only include the digits 0 to 9. System lock (Menu 4-3-7) To lock the communicator, press Select and enter your lock code. The communicator locks immediately. Even if you remove and replace the battery and switch on the phone, the communicator will remain locked. To unlock the communicator, press Unlock and enter the lock code.
Restore factory settings (Menu 4-4)
You can reset the settings of the menu functions to their original values. When you activate this setting, you will be prompted for your five-digit lock code. This function will not affect stored phone numbers and names, access codes, earpiece volume setting, call timers, cost counters, selected application tones or short messages.

Call divert (Menu 5)

The call divert network service allows you to direct your incoming voice calls to another phone number when you do not want to be disturbed, or when the phone is switched off or outside the network coverage area. The call diverting functions are described in more detail in Telephone settings on page 58. 1 Scroll to one of the following divert options and press Select: Divert all voice calls Divert when busy Divert when not answered Divert if not reachable Divert all fax calls Divert all data calls Cancel all diverts 2 Scroll to Activate. You will be asked for the phone number to which you wish to divert the incoming calls. The Cancel option sets the divert mode off. Status shows what kind of calls are being diverted.

Recorder (Menu 6)

With the Recorder you can record your telephone conversations and voice memos, and listen to them. The maximum length of a recording is 30 seconds. See also Voice recorder on page 135. Note: Local laws may apply to recording conversations. Do not use this feature illegally.
To record your own speech
1 In the Recorder menu, press Select. 2 Scroll to Record and press Select. 3 To stop the recording, press Stop.

11. Infrared problems

The communicator may be connected to a PC, laptop, printer, digital camera, wireless phone or another communicator via the infrared link. If you are using the PC Suite for Nokia 9110 Communicator program on your PC, or if you want to receive data from another communicator or a digital camera, you will have to start the Infrared activation application on your communicator before the connection is made. See Infrared activation on page 121. If you are using the Nokia Communicator Server program on the PC, the infrared connection is established automatically when you use one of the PC connectivity applications of the communicator. The PC to which you want to establish the connection must have an IrDA compatible infrared port; installed and activated IrDA drivers; and Microsoft Windows 95/98. For more information on IrDA drivers and their use in Windows 95, contact Microsoft. Note: The infrared connection in Windows 2000 and NT 4.0 is not compatible with the communicator. When using these operating systems, connection to the PC should be made via cable, see instructions on page 36. For further information, see the Documentation section on the CD-ROM in the sales package of the communicator.

12. Printing problems

If you are using the infrared connection, the infrared port of the printer must be compatible to the IrDA standard. See Document features on page 30. If you fail to establish an infrared connection, transfer the file to a PC and use the PC to print the document. Alternatively, you can fax the document to the nearest fax machine. See To send faxes on page 64. Check that your printing settings are correct, see System settings on page 115. You may be using an incorrect printer driver, see Document features on page 30.
13. PC connectivity problems
Make sure that the correct PC connectivity program is installed and running on your PC. See chapter 4 "Computer connectivity" on page 35. Check the cable or infrared connection used. If you use an infrared connection, the IR ports must be facing each other. Check that you are using the correct COM port.

To record a call....73 To make a new call during a call..73 To make conference calls...74 To transfer calls...76 To answer a waiting call....76 To send DTMF tones during a call...77 Telephone Settings....77 Flight profile....91

Contacts...93

Contacts directory...93 To make a contact card....94 To open a contact card....96 To move or copy contacts from a SIM card..96 To search for a contact card...96 To change fields in a contact card...97 To attach a ringing tone....99 To insert a picture....99 To create or modify templates...100 To store DTMF tones....101 To create contact groups...102 To create a SIM contact card...104 To send a contact card as a business card..105
Linda1.book Page 8 Friday, April 12, 2002 8:31 PM
To receive a business card... 106 Settings.... 107 To create a new contacts database.. 109

Calendar...111

Calendar entries.... 111 Views.... 118 Icons..... 125 Task lists.... 126 To search for Calendar entries... 127 Settings.... 128

Internet...131

To set up your Internet access point... 132 To connect to the World Wide Web... 141 To open a Web page.... 142 To browse the WWW... 144 WWW settings.... 147 Cache, History, and Plug-ins view... 149 Bookmarks.... 149 WAP.... 151 Java..... 156
Linda1.book Page 9 Friday, April 12, 2002 8:31 PM

Messaging....157

Messaging centre....158 Fax....166 Mail.....170 Short Message Service...183

Office....189

Word Processor....189 Sheet....194 Presentation viewer....202 File manager....204

Extras....213

Clock.....213 Calculator....215 Control panel....216 Recorder....229 Imaging.....231 Cell broadcast....234 Fax modem....237

Troubleshooting...241

Linda1.book Page 10 Friday, April 12, 2002 8:31 PM
CARE AND MAINTENANCE..255 IMPORTANT SAFETY INFORMATION..257 Glossary...265
Linda1.book Page 11 Friday, April 12, 2002 8:31 PM
FOR YOUR SAFETY Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this manual. Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST Dont use the communicator while driving. INTERFERENCE All wireless phones may get interference, which could affect performance. SWITCH OFF IN HOSPITALS Follow any regulations or rules. Switch the phone off near medical equipment. SWITCH OFF IN AIRCRAFT Wireless devices can cause interference in aircraft. SWITCH OFF WHEN REFUELLING Dont use the phone at a refuelling point. Dont use near fuel or chemicals. SWITCH OFF NEAR BLASTING Dont use the phone where blasting is in progress. Observe restrictions, and follow any regulations or rules. USE SENSIBLY Use only in the normal position. Dont touch the antenna unnecessarily. QUALIFIED SERVICE Only qualified personnel may install or repair phone equipment.

Getting help

Online Help
The communicator has a help function, which you can access from any application or view. To view help, press the key on the communicator interface keyboard. You are shown a page of information relevant to the task you are doing. You can also search the help topics for specific subjects and keywords.
About the guides in the sales package
The Nokia communicator sales package contains the following guides either in print or as PDF files. To help you begin to use your communicator, turn to the Getting Started Guide supplied in your sales package. It explains the start-up procedure and gives basic information on how to use the various applications.
This users guide explains in more detail how the Nokia 9210i Communicator operates. General information identifies the various parts of the communicator and their functions, as well as the common features of the communicator. The rest of this users guide deals with the communicator applications and the phone. There is a short glossary of Internet and wireless terms and abbreviations at the back of the users guide. The PC Suite Guide explains the functionality of PC Suite for the Nokia 9210i Communicator. With PC Suite you can move, copy, synchronise, back up, and restore data between your communicator and a compatible PC. The Software on CD-ROM Guide explains in detail the functionality of the applications found on the CD-ROM that you can install on your communicator. The Add-on Applications Guide gives a brief introduction of other software available for the Nokia 9210i Communicator. This guide is only available in a printed version. The Settings Checklist helps you to connect your Nokia 9210i Communicator with different kinds of wireless services. The PC Suite Guide and the Software on CD-ROM Guide are both on the CD-ROM under the section Using the Nokia 9210i Communicator. In this users guide and the Getting Started Guide, the names of the commands on the display are in bold and the settings and options are in italics. Note: If you are switching from the Nokia 9000 Communicator, the Nokia 9000i Communicator, the Nokia 9110 Communicator, or the Nokia 9110i Communicator to the Nokia 9210i Communicator, see To transfer data from other devices on page 36 and in the PC Suite Guide on the CDROM.

Introduction

5 Introduction
Facts about your communicator

Network Services

The wireless phone described in this guide is approved for use on the GSM 900 / 1800 networks. Dualband/triband is a network dependant feature. Check with your local service provider if you can subscribe to and use this feature. A number of features included in this guide are called Network Services. These are special services that you arrange through your wireless service provider. Before you can take advantage of any of these Network Services, you must subscribe to them through your service provider and obtain instructions for their use from your service provider. Note: Some networks may not support all language-dependent characters and/ or services. Check the model number of any charger before use with this device. This device is intended for use when supplied with power from ACP-9, ACP-12 chargers. Warning: Use only batteries, chargers and accessories approved by the phone manufacturer for use with this particular phone model. The use of any other types may invalidate any approval or warranty applying to the phone, and may be dangerous.For availability of approved accessories, please check with your dealer.When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord.
Services that need to be subscribed to are typically the short message service, Internet, and fax. After you have subscribed to the service functions, you can then activate these functions as described in this users guide. The manual activation commands for various services are not presented in this users guide (for example, using the and characters for activating or deactivating services). The Nokia 9210i Communicator, nevertheless, is capable of handling commands given in that form. For these commands, please consult with your service providers. Because the number of special services depends on what services are available in your home network, it is, unfortunately, impossible to provide a comprehensive list of the services and settings you need in this users guide. Therefore, this users guide gives general information about additional services. Please contact your network operator for further information about the availability and the details of services in your home network. Tip: Write the information you obtain from your service provider down on the Settings Checklist for future reference. If a service requires separate phone numbers or specific settings, they must be stored in the settings of the communicator. For example: Sending and receiving short messages requires that this service is supported by the network you are using and activated for your SIM card, and that the phone number of the message centre is stored in the settings of the SMS application. Internet access requires that data service is supported by the network you are using and activated for your SIM card. In addition, you must have obtained an Internet access point from an Internet service provider.

Infrared connection Charger connection RS232 adapter cable DLR-2L or headset HDC-8L connection

Figure 7

Linda1.book Page 21 Friday, April 12, 2002 8:31 PM

21 General information

Use the infrared port for connecting to a compatible PC, printer, digital camera, or another communicator.

To charge the battery

Note: See important safety information on battery usage on page 22. 1 Connect the charger cable to the bottom of the communicator, as shown in Figure 8. Tip: To check the current battery level, see the battery indicator on the communicator or phone display.
Figure Connect the charger to the proper voltage AC wall outlet. While charging is in progress, the battery level indicator scrolls on the phone display. 3 When the battery is fully charged, the bars stop scrolling and four bars are displayed. You may now remove the charger plug from the communicator. Note: You can use all the features of the communicator during charging.
Linda1.book Page 22 Friday, April 12, 2002 8:31 PM

22 General information

When the battery level is low and only a few minutes of operation time remain, a warning tone will sound, and the message BATTERY IS LOW will be repeated at regular intervals on the phone display. When the charge level becomes too low for operation, the RECHARGE BATTERY message will be displayed, accompanied by a warning tone. If you do not connect the communicator to a charger, the communicator switches itself off. Note: When you connect a communicator with a fully discharged battery to a charger, it will take 30-60 seconds before the CHARGING message appears on the display and the battery indicator bar starts scrolling. After that, it may take 10-30 seconds before you can switch the phone on.

Battery information

Tip: Read this section for information on how to prolong the life of your battery. Use the battery only for its intended purpose. Never use any charger or battery which is damaged. Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or pen) causes direct connection of the + and terminals of the battery (metal strips on bottom of the battery) for example when you carry a spare battery in your pocket or purse. Short- circuiting the terminals may damage the battery or the connecting object. Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15C and 25C (59F and 77F). A communicator with a hot or cold battery may temporarily not work, even when the battery is fully charged. Batteries' performance is particularly limited in temperatures well below freezing.
Linda1.book Page 23 Friday, April 12, 2002 8:31 PM
Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. Note that a new batterys full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery. Use only batteries approved by the communicator manufacturer and recharge your battery only with the chargers approved by the manufacturer. Unplug the charger when not in use. Do not leave the battery connected to a charger for longer than a week, since overcharging may shorten its lifetime. If left unused a fully charged battery will discharge itself over time. Temperature extremes can affect the ability of your battery to charge. Battery operation time is affected by the following: whether both the phone and the communicator interface are on, radio signal strength, various phone settings, and the length of the screen blanker period. It is always recommended to keep a charged battery in the communicator. Keeping the battery charged maximises the lifetime of the backup battery supplying power to the real-time clock of the communicator. In case the backup battery is drained, it will be automatically charged the next time a charged battery is reconnected to the communicator. Always close the device cover before removing the battery. Closing the cover will save all data.

Tip: Replace all is available only if you have selected Yes in the Replace all dialog.
Tip: You can select individual words to spell check. Otherwise the whole text is searched and spell checked.
General_information_Iss3.doc Page 32 Friday, October 18, 2002 5:37 PM

32 General information

To print
You can print various items, such as documents, pictures, faxes, mails, and short messages. Refer to the users guide of the printer for detailed safety instructions on the printing device. To view or modify the page setup, press the Menu key and select File > Printing > Page setup To preview the document before printing it, press the Menu key and select File > Printing > Print preview To print a document or a file, 1 Press the Menu key and select File > Printing > Print. A note appears, showing the print range, connection type, and printer used. 2 Press Print. A dialog opens. To change the printing options, press Options. 3 To preview what you are about to print, press Print preview. A dialog opens. To define page setup, press Page setup.

Figure 11

General_information_Iss3.doc Page 33 Friday, October 18, 2002 5:37 PM

33 General information

Tip: The shortcut to open the log is Shift+Ctrl+L. Tip: To change the categories Date and time and Duration to Subject and Status, press < and > on the Arrows key. When printing via infrared, make sure that the infrared port of the communicator faces the infrared port of the printer. Keep the infrared connection clear. If the connection is obstructed for too long, for example, if something is moved between the infrared sensors or the communicator is moved, printing is interrupted. For details on infrared connection, see page 35.
Log contains information about the communication history of your communicator. The log shows all, or certain types of communication events in chronological order. With log files you can monitor your communications, use the information to create or complete contact cards, or reply directly to the sender in the log.

Figure 12

To access the log
You can access the log from the Menu of several applications. Press the Menu key and select Tools > Log.

General_information_Iss3.doc Page 37 Friday, October 18, 2002 5:37 PM
2 On each page, press Change to select or deselect the data categories to transfer to the Nokia 9210i Communicator. To select or deselect all items on a page, press Select all or Unselect all. When you are ready, press Done. 3 In the main view, press Transfer now. Activate the infrared connection on the Nokia 9110/9110i Communicator. The transfer begins. All items are transferred to the Nokia 9210i Communicator. 4 When the transfer is complete, press OK to close the application. 5 If the transfer fails, a dialog is displayed. Press OK to try again. Note: You can cancel the transfer process at any stage when the Cancel command button is available.
Compatible Nokia phones, personal organisers, and PCs
To transfer data from the Nokia 5100/6100/7100/8200/8800/9110/9110i mobile phone, your laptop or desktop PC, or the PalmPilot personal organiser to your Nokia 9210i Communicator, see the PC Suite guide on the sales package CD-ROM. Note: To transfer contacts from your old SIM card to your Nokia 9210i Communicator, see To move or copy contacts from a SIM card on page 96. Tip: To transfer data from other personal organisers, first synchronise data between the device and the PC application and then synchronise data between the PC application and the Nokia 9210i application.
General_information_Iss3.doc Page 38 Friday, October 18, 2002 5:37 PM

38 General information

Linda1.book Page 39 Friday, April 12, 2002 8:31 PM

39 Phone

Front Back Earpiece Microphone

3. Phone

Figure 13 With the cover phone you can make, receive, and manage calls, send and receive short messages, search for phone numbers, change profiles and define many settings. For more complicated tasks like sending long DTMF sequences or modifying phone settings, use the Telephone application. See the Telephone chapter, starting on page 69.
Linda1.book Page 40 Friday, April 12, 2002 8:31 PM

40 Phone

Selection keys
When operating the phone, press keys one at a time. The phone keypad is not functional when the cover of the communicator is open. Switches the phone on and off. Switches between profiles. See Profile settings on page 78. Scroll through menus, submenus or settings. If there are no active calls, you can use the scroll keys to browse through the phone book. When a call is active, you can adjust the volume level by pressing the scroll keys. Tip: To call your voice mailbox, press and hold. Dials a phone number and answers a call. Sends the ongoing call to hold if pressed during a call. In the standby mode shows the list of the most recently dialled numbers. Ends any active call, cancels a dialled call, or clears the display. 0.9 Tip: If you have subscribed to two phone lines, you can switch between them by pressing and holding. The number and alphabet keys. Used for creating functions. The function of these two selection keys depends on the text shown on the bottom of the display. See Figure 14. Note: Hold the phone as you would any other mobile phone with the antenna pointed up and over your shoulder. Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.

Linda1.book Page 105 Friday, April 12, 2002 8:31 PM

105 Contacts

Figure 36

SIM directory options

You can sort the contents of the SIM directory in alphabetical order or by memory location. Press the Menu key and select View > Sort by > Name, or Sort by > SIM location. To see a summary of the usage of the SIM database, press the Menu key and select File > Properties. If fixed dialling is active, you can see only information about fixed dialling numbers.
To send a contact card as a business card
When you send or receive a contact card between the communicator and other devices, the term business cards is used. A business card is a contact card in a format suitable for transmission, usually vCard format. You can add received business cards to your Contacts directory, where they become contact cards. 1 In the Contacts directory main view, select the card you want to send. Tip: You can send only one business card in each message you send; however, you can send it to many recipients.
Linda1.book Page 106 Friday, April 12, 2002 8:31 PM
Tip: PC mail and the short message service are explained in the Messaging chapter, starting on page 157. If a contact card is sent as a short message, the card is sent in the Sending format defined on page 108. 2 Press the Menu key and select File > Send. In the Send submenu, make a further choice of media: As a mail/As a short message/Via infrared. You may have other sending options if you have installed additional software. An editor dialog opens, depending on the sending medium you have chosen, as shown in the example below. The contact card you want to send has now become a business card.
Figure 37 Tip: If you change the setting to include images in the message, do not forget to change it back after you have sent the message to reduce call charges. 3 To choose who receives the sent card messages, press Recipient. 4 If you are sending via the short message service, the images are left out by default to reduce call charges. If you want to include the image in the message, you must change the setting. See Send as a short message page on page 108. 5 If you are about to send via infrared, make sure you activate the receiving of infrared in the other device first. 6 Press Send.
To receive a business card
When you receive a business card from another device, you are alerted by a notification message. This message appears automatically on the display, in any application. Follow the screen prompts to view the business card.
Linda1.book Page 107 Friday, April 12, 2002 8:31 PM
A field is displayed if it is recognised; if not, it is ignored. Audio data, in a supported format, is set as the personal ringing tone of the contact (if you choose to add the card to your Contacts directory) To add the received card to your Contacts directory, press Add to Contacts. The card is converted to contact card format. To reject the card, press Delete.

To open a frame as a new page
To open the currently active frame as a new page and discard the other frames, press the Menu key and select File > Open > Frame as new page

To view pages offline

To view local downloaded pages on your communicator without accessing the WWW, press the Menu key and select File > Browse Offline

WWW settings

To change the WWW settings, press the Menu key and select Tools > Settings. A dialog with two pages opens. See Figure 62.

To change frame sizes

Linda1.book Page 148 Friday, April 12, 2002 8:31 PM

148 Internet

Figure 62
Show images: The options are Yes/No. If you select Yes the WWW browser loads all the pictures on a Web page when it displays the Web page. Frames options: The options are Show all frames/Show frames one by one/Do not use frames. Some Web pages are split into several frames, which makes reading difficult, so choose an option which suits you.

Advanced page

Use cookies: Some Web pages store data on your communicator in files called cookies. Use this setting to determine whether to accept cookies, and if you accept them, whether you wish to be prompted each time a cookie is stored. The options are Always/Never/Ask. Empty cache on exit: If you select Yes, the cache memory is emptied when you exit the WWW browser. The options are Yes/No.
Tip: To empty the cache immediately, press the Menu key and select Tools > Clear cache.
Linda1.book Page 149 Friday, April 12, 2002 8:31 PM
Note The information or services you have accessed are stored in the cache of your phone. A cache is a buffer memory, which is used to store data temporarily. If you have tried to access or have accessed confidential information requiring passwords (for example, your bank account), empty the cache of your phone after each use. Empty history list on exit: If you select Yes, the history list is emptied when you exit the WWW browser. The options are Yes/No.
Cache, History, and Plug-ins view
These views display a list of information on cache memory, browser history and installed plug-ins. To view information about the cache memory used for temporary storage of the pages you visit, press the Menu key and select Information > Cache. To view information about the sites you have visited, press the Menu key and select Information > History list. To view what add-on software for the WWW browser has been installed, press the Menu key and select Information > Plug-ins. Plug-ins can display documents that the WWW browser itself cannot show, such as multimedia clips. You can download plug-ins from the WWW.

174 Messaging

IMAP4 folder path: Define the location of the IMAP mail folder here, if not defined automatically. This option is available only if the mailbox type is IMAP4.

To edit an account

1 Press the Menu key in the main view of Messaging and select Tools > Account settings. A list of accounts opens. 2 Select the account you want to edit and press Edit. 3 Define the settings on the General, Servers, Retrieve and Advanced pages explained above. 4 Press the Esc key to discard any changes. Press Done to accept the changes you have made. Note: You cannot edit mailbox settings when online.
To write and send new mail
Tip: If you cannot send mail from your communicator, check first that your mail address is correct in Mail settings. See page 171. 1 Press Write mail in the main view of Messaging. The mail editor opens, see figure 73.
Figure 73 Tip: To see how to select recipients, see page 163. 2 Write the mail message.
Linda1.book Page 175 Friday, April 12, 2002 8:31 PM
3 Press Recipient to select the recipient or recipients of the message, or type in the name or mail address into the To:, Cc: and Bcc: fields. You can move from one insertion field to another by pressing the Tab key. 4 If you wish to adjust the sending options of the mail message, press Sending options. A dialog with two pages opens, see page 176. 5 Press Send. Note: You cannot enter accented characters, such as or , into mail addresses.

Recipients

There are three hierarchy levels of recipients in a mail message: To: - Message is sent directly to the recipient. Cc: - A copy of the message is sent to the recipient, and the recipients name is visible to other recipients of the message. Bcc: - A copy of the message is sent to the recipient, but the recipients name is not visible to other recipients of the message. Note: The addresses you have entered are checked against your contacts database once you press Send. Names which do not match with the contacts database, or addresses which do not have @, should be removed from the address fields. If a name you have entered in one of the address fields matches a group name, the name is replaced with the mail addresses of the group members.

11. Extras

Extras contains the following applications: Calculator, Clock, Control panel, Recorder, Imaging, Cell broadcast, Video player, and Fax modem. Most of the new applications that you install will be added to the Extras application group. For more information on applications available on the sales package CD-ROM, see Software on CD-ROM Guide in the Using Nokia 9210i Communicator section of the CD-ROM.

Figure 88

The Clock shows the time and date in your home city and country or region, as well as in several other cities and countries in the world. The Clock also includes an alarm clock. To set the current date and time for your communicator, press the Menu key and select Tools > Date and time.
Linda1.book Page 214 Friday, April 12, 2002 8:31 PM
Tip: To choose the clock type, press the Menu key and select View > Clock type > Digital or Analogue.

Extras

To set an alarm
Press Alarm clock in the main view. An alarm clock view opens. The currently active alarms are listed next to the clock. To create a new alarm, press New alarm or to edit an alarm, press Edit alarm. Define the Time of the alarm and the frequency in Occurrence and Day fields. Define also the Description displayed when the alarm goes off. 5 Press Done to accept the set alarm.
Tip: To turn off a sounding alarm, press Stop or any key on the keypad of the phone cover. Press Snooze to silence the alarm for five minutes.

To change your home city

If your home city and time settings on your communicator are not set correctly, you must first set your home city and then set the time, since your home location defines the time zone used. 1 Go to the World clock main view. 2 Press Change city. A cities view opens. See figure 89.
Tip: The world map shows the currently selected city in cross hairs.
Figure Type the city in the search field or scroll the list and press Select when ready. 4 Press OK to accept the change of time zone or Cancel to dismiss it.
Linda1.book Page 215 Friday, April 12, 2002 8:31 PM

Imaging

Linda1.book Page 232 Friday, April 12, 2002 8:31 PM

232 Extras

You can also receive images via IR. For details, see To receive images via infrared on page 234.

To create a new album

1 Press the Menu key and select File > New album. A dialog opens. 2 Define the following: Name: Name of the album. 3 To save the album in the communicator, press Create locally. To save the album in a memory card, press Create in mem. card.

To view album contents

Tip: To open an image located outside the image albums, select File > Open from. 1 Select the album in the Imaging main view and press Open. A thumbnail view of the album contents opens. 2 You can scroll the contents of the album with the Arrows key. To open an image for viewing, press Open. 3 To view the next frame in the image, if available, press the Menu key and select View > Next frame. To return to the previous image, select Previous frame. 4 Press Close to return to the thumbnail view.
To move images to and from albums
1 Select the image or images in the thumbnail view with the Arrows key.
Linda1.book Page 233 Friday, April 12, 2002 8:31 PM
Press the Menu key and first select Edit > Copy or Cut. Open the target album. Press the Menu key and select Edit > Paste. If the target album already has an image or images with the same name, a confirmation note appears asking you if you wish to replace the existing image. Choose from the following options: Replace - The existing image is replaced with the image you are pasting. Replace all - All existing images are replaced with the same name. Skip - Skips the image and continues the operation. Cancel - Cancels the whole paste operation. Tip: You can select several images with the Space key. You can also use the Edit menu commands and the corresponding shortcuts (Ctrl+c, Ctrl+x, Ctrl+v) to move or copy images.
To create new images from originals
You can choose parts of an opened image, save them as separate images, and reuse them. 1 Open an image. Press the Menu key and select Edit > Select image range. The selection frame is now visible on the image. 2 To move the selection frame, use the Arrows key. To change the size of the selection frame, press down the Ctrl key and use the Arrows key. 3 To save the frame as an image, press the Menu key and select File > Save as. Select Selected range. 4 Select the folder you wish to save in, give a name for the new image file, and press OK.

Linda1.book Page 248 Friday, April 12, 2002 8:31 PM
3 If the data call is active, but you cannot download WWW pages with the WWW browser, make note of the most recent status indication displayed to you in the title bar of the WWW browser. If the status indication reads Waiting for reply from host or Looking up host address, it is likely that the WWW address (URL) has been mistyped, or there is a problem with proxy server settings in the Internet Access Point or the proxy server itself, or there is a transient problem with the WWW server or Internet connections between the WWW server and your Internet Service Provider. Check the proxy server settings explained on page 135. Disconnect the call, wait for a couple of minutes, and retry the connection. If the connection still does not succeed, contact your Internet Service Provider. If the status indication reads Logging into network or Connected, the problem is most likely in your Internet Access Point settings (See page 132 for details) or your Internet Service Providers dial-up system, or you might need a script in order to connect to your Internet Service Provider. Disconnect the data call, wait for a couple of minutes, and retry the connection. If the connection still does not succeed, contact your Internet Service Provider. 4 If your data call is unexpectedly dropped, this may be a case of poor network conditions, congestion in the phone network, or a too low inactivity period setting. If you are unable to connect to the Internet after repeated attempts, and have successfully used your Internet connection previously, or get error messages when starting the WWW browser, remove and replace the battery and try again. 12. Infrared problems The communicator may be connected to a PC, laptop, printer, digital camera, wireless phone or another communicator via the infrared connection.

Troubleshooting

Linda1.book Page 249 Friday, April 12, 2002 8:31 PM

249 Troubleshooting

If you are using the PC Suite for Nokia 9210i Communicator program on your PC, or if you want to receive data from another communicator or a digital camera, you must activate the Infrared connection on your communicator before the connection is made. See PC Suite Guide in the sales package CD-ROM and To activate the infrared connection on page 35 of this guide. The PC to which you want to establish the connection must have an IrDA compatible infrared port; installed and activated IrDA drivers; and Microsoft Windows 95/98/98SE/Me. For more information on IrDA drivers and their use in Windows, contact Microsoft. If you have an IBM Thinkpad laptop with Windows 98 SE installed, you may encounter problems with infrared connections. If problems occur, proceed as follows: 1 Click the Windows Start button and select Settings > Control Panel. 2 In the Windows 98 Control Panel, open System. 3 In the System properties dialog, select the Device Manager tab. 4 Under Network Adapters, select IBM Thinkpad Fast Infrared Port and click the Properties button. IBM Thinkpad Fast Infrared Port Properties dialog opens. 5 Click the Driver tab and then click the Update Driver. button. Update Device Driver Wizard starts. 6 Click Next. 7 Select the Install one of the other drivers option and click the View List. button. 8 Infrared PnP Serial Port has been found. Click OK. 9 Click Next. 10 Infrared PnP Serial Port is ready to be installed. Click Next. 11 The new driver has been installed. Click Finish. 12 The computer must be restarted before the new driver can be taken to use. Click Yes to restart the computer.

Linda1.book Page 268 Friday, April 12, 2002 8:31 PM
IETF (Internet Engineering Task Force) IETF are responsible for most of the Internet standardisation. Nokia 9210i Communicator is using many IETF specifications. In the callback settings, one of the settings is specified by IETF whereas the other methods are specified by Microsoft. ISDN connections ISDN connections are a way to establish a data call between the Communicator and your Internet Access Point. ISDN connections are digital from end to end and as such offer quicker set-up times and faster data rates than Analog connections. In order to use ISDN, both your Internet service provider and network provider have to support them. Java An object-oriented, general purpose programming language developed by Sun Microsystems and originally designed for handheld devices. Java is language similar to C++, but simplified to eliminate language features that cause common programming errors. Compiled Java code can run on most computers because Java interpreters and runtime environments exist for most operating systems Lock code The lock code is a five-digit code needed to lock and unlock the communicator. The default lock code for Nokia 9210i Communicator is 12345. The lock code is also required when you change certain settings. Keep it secret and in a safe place, separate from the communicator.
Linda1.book Page 269 Friday, April 12, 2002 8:31 PM
MCN (Micro-Cellular Network) technology Microcells are used for increasing the capacity of wireless networks in urban areas. MIME (Multipurpose Internet Mail Extensions) A standard Internet format which permits, for instance, multiple mail objects in a single message. The mail objects can be, for example, formatted multifont text messages and non-textual elements, such as images and audio fragments. PIN (Personal Identity Number) The PIN code protects your phone from unauthorised use. The PIN code is supplied with the SIM card. If the PIN code request is selected, the code is required each time the phone is switched on. The PIN code must be 4 to 8 digits long. PIN2 Code The PIN2 code is supplied with some SIM cards. The PIN2 code is required to access certain functions supported by the SIM card. The length of the PIN2 code is 4 to 8 digits. Plug-in A plug-in is add-on software that can be downloaded from the WWW. The communicator uses plug-ins to display a document that the WWW application itself cannot show POP3 (Post Office Protocol, version 3) A common mail protocol that can be used for accessing the Remote mailbox.
Linda1.book Page 270 Friday, April 12, 2002 8:31 PM
Point-to-point protocol (PPP) A common networking software protocol which enables any computer with a modem and a phone line to connect directly to the Internet. Protocol A formal set of rules that govern how data is transferred between two devices. Proxy In some networks, the connection between the WWW and the site you want to connect to is blocked by a firewall. The firewall protects the network from unauthorised external access. A proxy is an intermediary program that enables access through the firewall. A proxy can also serve as a network cache to speed up the retrieving process. PUK (PIN Unblocking Key) code The PUK is an 8-digit code supplied with the SIM card. The code is required when you want to change a disabled PIN code. If you enter an incorrect PUK code ten times in succession, the SIM card is rejected and you cannot make or receive any calls, except emergency calls. When the SIM is rejected, you will need a new SIM card. You cannot change the PUK code. If you lose the code, contact your network service provider. PUK2 Code The PUK2 code is supplied with some SIM cards. The code is required when you want to change a disabled PIN2 code. If you enter an incorrect PUK2 code ten times in succession, you will not be able to access the functions