FCN+2 XFER

FCN 4 Last No. FCN 7 PICK FCN 5 FWD FCN 8 PAGE
FCN 3 CONF FCN 6 SPEED FCN 9 Exit Menus
Wireless Telephone Quick Reference Guide Nortel Norstar ICS or BCM M7310 Station Set

LINE 0 RLS

LINE * FEATURE

LINE 1 LINE 2

LINE 6 LINE 7

LINE 3 LINE 4

LINE 8 LINE 9

LINE 5

Norstar M7310 Station Set
Pressing LINE followed by a digit (1-9) on the Wireless Telephone is equivalent to pressing one of the 9 line keys on the M7310. Pressing FCN followed by a digit (2-9) on the SpectraLink Wireless Telephone is equivalent to pressing one of the memory buttons on the top of the M7310 set. FCN 1 is reserved for MUTE. Memory buttons 10-12 on the M7310 cannot be accessed from the SpectraLink wireless telephone. FCN followed by 0, * and #, is equivalent to pressing one of the three soft keys just below your display. Pressing LINE * gives you access to your Feature programming. LINE 0 allows you to release the phone call.
Function Key Strokes FCN + 1 FCN + 2 FCN + 3 FCN + 4 FCN + 5 FCN + 6 FCN + 7 FCN + 8 FCN + 9 FCN + * FCN + 0 FCN + # LINE + 0 LINE + * 72-0170-09-B RLS FEATURE Norstar is a trademark of Nortel Networks Default settings MUTE XFER CONF LAST NO FWD SPEED PICK PAGE EXIT MENUS For information on Battery Pack charging and setting user preferences, see the Wireless Telephone User Guide. User Options Mute On/Off Function Fill In Your Feature Settings Hold Take off Hold

Wireless Telephone

On/Off
Make a call Hang up Answer call Press and hold PWR. Two chirps on, one chirp off Press START to get dial tone. Press END. Be sure to do this at the end of each call. Press START. Line indicator comes on steady when the call is answered. Press HOLD to put your current call on hold, or END to hang up. Press LINE + the digit that is flashing. Press HOLD Press LINE followed by the digit for the line on hold, which will be flashing. Press FCN and then 1 Pressing FCN while off hook allows you to scroll through menu screens. Press FCN while on hook to change handset settings.

Answer second call

Enterprise Edge M7310 Quick Reference Guide
2000 Nortel Networks P0908513 Issue 03
Your Enterprise Edge M7310 Telephone
Shift button For using the top function of a dual-memory button. Display shows the time, date, call information, and guides you. The lower line of the display is reserved for display button instructions. Dual-memory buttons store any two features and/or autodial numbers. Display buttons Feature button starts or ends a feature. Release button cancels active calls. Hold button Dial pad Memory and line buttons are buttons with indicators for one touch dialing, feature operation or line access. Volume control Indicators appear beside lines and features.

Using display buttons

Three display buttons appear directly below the display. When active, these buttons appear in capital letters on the second line of the display. In this document, display buttons appear as underlined, capital letters: for example, OK.

1. 2. 3. 4.

Contrast level 2 DOWN UP OK
Display message Display button message Display buttons

Using Button Inquiry

Check what is programmed on your memory buttons.
Release all calls or lines with dial tone. Press. Press the button(s) that you want to check and read the display. Press when finished.
Adjusting display contrast Selecting a ring type and volume level
1. Press. 2. Press UP or DOWN for the level you want. 3. Press OK when finished. 1. Press. 2. Press , , , , or NEXT to hear the different ring types. 3. While the telephone is ringing, press to adjust the volume level. 4. Press OK to store the volume level and ring.
Page 1 Enterprise Edge M7310 Quick Reference Guide
Making and answering calls
Answering calls Answering calls using the handset When your telephone rings, or flashes beside an Intercom or line button:

1. Lift the handset.

OR Press the button beside the flashing before lifting the handset. Answering calls using Handsfree When your telephone rings, or flashes beside an Intercom or line button:

1. Press.

Making calls
Depending upon the dialing mode programmed on your telephone, you may have to lift the handset before making a call. External calls using numbered line buttons
1. If you do not have an external Prime line, press a line button. 2. Dial your call.
External calls using Intercom buttons
1. Lift the handset. 2. If appears beside an Intercom button, enter a line pool access code.
OR Press an Intercom button without , then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press. 2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by your System Administrator.
1. Press. The flashes beside the line on hold. 2. Press the line button with the flashing to return to the call.

Holding Calls

Automatic hold Calls are put on hold automatically when you switch from one line to another. Exclusive hold Use Exclusive Hold () to keep a call on hold so that it can be retrieved only at your telephone.
Page 2 Enterprise Edge M7310 Quick Reference Guide
Making and answering calls continued
1. Press and replace the handset to switch to Handsfree. 2. Pick up the handset to switch back. 1. Press microphone OFF. 2. Press again to turn the microphone ON.
System Administrator can program Handsfree for your telephone. Switching between Handsfree and handset

Using Mute

Making calls using Handsfree Notice
Press instead of lifting the handset.
This telephone now conforms to the latest standards in relation to the positioning of Q and Z on the number keys. The Q appears on key number 7 and the Z appears on key number 9.
Page 3 Enterprise Edge M7310 Quick Reference Guide 3 Page 6 Enterprise Edge M7310 Quick Reference Guide
Programming memory buttons
About memory buttons Memory buttons store telephone numbers or feature codes to give you one-touch dialling or feature activation. To use the top function, press the shift button, then press the dual-memory button. There are two types of memory buttons: single-memory and dual-memory. Dual-memory buttons: To use the bottom function, press the dual-memory button. Single-memory buttons: Single-memory buttons are the buttons with indicators other than line or Handsfree buttons.

Remember: Press to check a memory or line button. Programming memory buttons External Autodial Internal Autodial
If you are on a call or an open line with dial tone, press or. Press. Press a memory button. Dial the station number. Label your new button. 1. If you are on a call or an open line 1. with dial tone, press or 2. Press. 2. 3. Press a memory button. 3. 4. Dial the external number. 4. 5. Press OK to store the number. 5. 6. Label your new button.

Features

Erasing memory buttons
If you are on a call or an open line with dial tone, press or. Press. Press the memory button you want to erase. Press OK to erase the button.
1. If you are on a call or an open line 1. with dial tone, press or. 2. Press. 2. 3. Press a memory button. 3. 4. Press and the feature code. 4. 5. Label your new button.
Page 4 Enterprise Edge M7310 Quick Reference Guide

Setting up the telephone

Connecting the cords ATTENTION Before attempting to carry out any work on the telephone, ensure that the line cord is unplugged from the wall socket. To remove any of the cords, squeeze the release latch on the plug and gently pull the plug from the socket. Connect the handset cord to the jack labelled with the telephone icon and route the cord as shown. If you are using a headset, route the cord along the channel in the base and connect the cord to the telephone jack that is marked with the headset icon. Route the line cord through the stand and connect the cord to the telephone jack that is marked with the jack icon. Attach the stand using the slots on the back of the telephone. Once the above work is complete, plug the line cord back into its wall socket.
Connect to jack from distribution block

Connect to receiver

Page 5 Enterprise Edge M7310 Quick Reference Guide
Mounting the telephone on the wall
Page 6 Enterprise Edge M7310 Quick Reference Guide

P0908513 Issue 03