Radio Installation Sheet for NS100 VHF system

Parts Checklist

SINGLE SYSTEM (NS100SS) 1 x VHF Black Box Radio (single) DUAL SYSTEM (NS100DS) 1 x VHF Black Box Radio (dual) 1 x Hailer Cable ADDITIONAL WITH EACH SYSTEM 1 x Hand set with cord (US) PART CODE

APNSBB2E8070

w w w.Nor th s tar Nav. c om

Wiring Setup

Antenna 10A Fuse
1 x Mounting Template - Speaker 1 x Quickstart Guide and Reference Manual 1 x Quickstart Guide 1 x Radio Installation Sheet 1 x Warranty Sheet
PPNSBB2E7030 PPNSBB2E7050

PART CODE

APNSBB2E8080
PPNSBB2E7070 PPNSBB2E7260 PPNSBB2E7100 PPNSBB2E7110 MPLILTD-4/80 Power/NMEA HLR Station 1 Station 2 Ground lug APNSBB2E8030
COLOR RED BLACK GREEN YELLOW ORANGE BLACK
FUNCTION PIN# BATTERY (+) 5 GROUND 1 NMEA IN (+) 2 NMEA IN () 6 NMEA OUT (+) 3 NMvEA OUT () 4
Power Cable Black Box Radio

PWNSBB2E7120

1 x DSC Sticker 1 x Dust Cap for Handset connector plate OPTIONAL ADDITIONAL HANDSET KIT (NS100HS) 1 x Hand set with cord (US)

APNSBB2E8030

Hailer Cable
1 x Mic Plate - black 1 x Black Box to Speaker cord with Female-Female Adapter 3 x SS self tapping screws 1 x Mic Clip with magnet 2 x SS self tapping screws for mic clip 1 x Large Speaker
MMNSBB2E4000 Female-Female adapter WALI08L07KX0 WALI08F08F0

COLOR YELLOW BLACK

FUNCTION HAILER (+) HAILER ()

PIN# 1 8

1 x Mic Plate - black 1 x Black Box to Speaker cord with Female-Female Adapter 3 x SS self tapping screws 1 x Mic Clip with magnet
MMNSBB2E4000 WALI08L07KX0 WALI08F08F0

Hand set & mike clip

MS35-20SPSX1 APNSBB2E8050 MS35-20TSPX1 APNSBB2E8060

10 pin socket

Hand set connector plate
MS35-20SPSXpin socket APNSBB2E8050 MS35-20SPSX1 APNSBB2E8060 Dust cap
2 x SS self tapping screws for mic clip 1 x Large Speaker

1 x Speaker Gasket

MPNSBB2E7040 Large speaker
1 x Speaker Gasket 4 x Speaker tabs 4 x SS self tapping screws 4 x SS self tapping screws 1 x Power Cable w/tags 1 x SS Grounding screw 1 x Spare 10A fuse 1 x Mounting Template - Black Box
PPNSBB2E3270 MS35-20SPSX1 MS35-20SPSX1 WALI06LXXXX0 MS30-06PSNX2 PKFU125V10A0 PPNSBB2E7080

MPNSBB2E7040

4 x Speaker tabs 4 x SS self tapping screws 1 x Installation Sheet 1 x Dust Cap for Handset connector plate
PPNSBB2E3270 MS35-20TSPX1 PPNSBB2E7030 MPLILTD-4/80

Tools Required

Drill 1-1/4 Hole Saw 1/8 Drill bit Phillips Screwdriver

Sabre saw

1 Hole Saw

Pencil

Installation Tips
Installing Handset Connector
1. Find a location for the Handset connector near the vessel steering wheel and check that there is enough wire length to reach the remote speaker location. Stretch the mike cord to be sure the handset is comfortable to use while driving. Using the black metal plate as a guide, mark the center of the hole to be drilled. Use a 1 hole saw to cut out the dash. Leaving the small rubber gasket on the backside of the connector, push it through the D hole in the plate. Put the rubber dust cap over the connector shaft and tighten the nylon nut. Hold the plate & connector assembly to the dash and mark the 3 holes. Use a 1/8 drill. Mount the plate with the 3 screws provided. Connect the handset connector. When removed, be sure to cover the connector with the provided dust cap.
Installing Microphone Clip Plate
1. Mount the handset near the mounted connector allowing a drip loop in the MIKE cord. Be sure there is about 2 of vertical clearance to allow the handset to be easily lifted off and returned to the clip plate. Place the clip plate on the dash with the magnetic sensor toward the rear. Using the clip plate as a guide, mark the 2 holes. Use a 1/8 drill. Mount the clip plate with the 2 screws provided. Mount the handset connector.
Speaker is at least 45cms (1.5') from the compass

2. 3. 4.

Black Box Radio must be at least 1metre (3) from the Antenna

Wiring Hailer Connector

Location Requirements - Please check these before doing any cutting or drilling. Ensure that the chosen location: is at least one metre (3') from the antenna allows easy connection to (at least) a 10 Amp fused 12V only DC electrical source and the antenna. is at least 45cms (1.5') from the compass to avoid creating magnetic deviation of the compass during radio operation has a suitable space close by for installing the microphone bulkhead mount provides easy access to the front panel controls provides reasonable access to the wiring at the back of the radio. 1. Check that the location of the powerful 20W 4 Ohm HAILER HORN (not provided) does not effect the ships compass before drilling holes and mounting. The Horn needs a clear view of the bow of the boat so the FOG and PA signals can be heard well by other vessels. Run 2 #20 AWG wires from the horn to the Box and connect to the HAILER connector wires. Follow the wire colors on the front of this sheet and crimp to the HAILER connector assembly wiring.

Installing Remote Speaker
1. 2. 3. 4. 5. Check the location does not effect the ships compass before drilling any holes. Using the template provided, use the 1-1/4 hole saw to cut out the 4 corners. Use the sabre saw to trim the remaining inside of the speaker cutout. Use the 1/8 drill bit for the 4 side mounting holes. Mount the speaker with supplied gasket from the front and hook up the connectors. No need to get behind the panel. Put the 4 speaker clips on the speaker to cover up the mounting holes for a professional look.

CAUTION

NOTE: DO NOT GROUND EITHER SIDE OF THE HAILER WIRES.
PPNSBB2E7080 ( L A040 6A)

NS100 MARINE VHF RADIO.

The Northstar NS100 marine VHF DSC radio, available in single and dual station models, combines the easeof-use and peace-of-mind you expect from Northstar and provides a wealth of useful features. The latest DSC SC-101 (US) or Class-D (EU) functions Dedicated distress call button automatically transmits MMSID and position until an acknowledgement is received Alphanumeric handset with built-in screen for easy operation and information display Access to all available marine VHF channel banks including weather Adjustable contrast on the handset LCD and adjustable backlighting on for low light and no light use The dual station model also offers: Second alphanumeric handset Intercom capabilities between handsets Foghorn mode Hailer function The NS100 radio - the features you need and the performance you expect from Northstar.

DISCOVER IT.

www.northstarnav.com
NS100 - Marine VHF DSC Radio handset sides, front & top. units: mm
NS100 - Marine VHF DSC Radio Blackbox & Speaker front and side

SPECIFICATIONS GENERAL:

Power supply: 13.6V DC Current drain: Transmit 6A at 25W Tx / 1.5A at 1W Tx Receive Less than 400mA in standby Useable channels (country-specific) International, USA, Canada, Weather Modulation mode: 16K0G3E (FM)16K0G2B (DSC) DSC: USCG SC-101 for US, Class-D for EU PHYSICAL: LCD display (viewing): 48(W)x24(H)mm FSTN 4x12 character Contrast & backlight control: Yes Temperature range: -15C to 50C
Waterproofing: Handset~JIS7 Speaker/ Box~IPX6 Frequency stability: +/- 10ppm Frequency control: PLL TRANSMITTER: Frequency: 156.025~157.425MHz Output power: 25W / 1 W selectable Max Freq deviation: +/- 5kHz Spurious & harmonics: Attenuated at least 43+10logPo (USA) 80dB@25W, 60dB@1W (EU) Modulation distortion: Less than 10%1kHz for a +/-3kHz deviation
RECEIVER: Frequency: 156.025~163.275MHz 12dB SINAD sensitivity: 0.25uV Adjacent CH selectivity: more than 80dB Spurious response intermodulation: more than 80dB Rejection ratio: more than 80dB Residual noise level: more than 80dB unsquelched Audio output power: handset~1W external speaker~2W hailer~20W into 4ohms
Specifications are subject to change without notice.
USA 30 Sudbury Road, Acton, MA 01720, USA Ph: +1 978.897.6600 +1 800.628.4487 Fax: +1 978.897.7241 sales@bntmarine.com EUROPE Unit 2 Ocean Quay, Belvidere Rd, Sothampton, SO14 5QY, England Ph: +339922 Fax: +330345 sales@northstarnav.com AUSTRALIA PO Box 479, Gladesville, NSW 2111, AUSTRALIA Ph: +9060 Fax: +9009 sales@northstarnav.com NEW ZEALAND Crystal Electronics Ltd PO Box 12 760, Penrose Auckland, NEW ZEALAND Ph: +Fax: +sales@crystal.co.nz

LA000503B