#56-1841-2

10/2007
#1841 ROOSTER CRAWLER ESC ADDENDUM
This Addendum addresses issues specific to the #1841 Rooster Crawler-Edition Brushed ESC and should be referred to instead of the original instructions for the changes as noted below. This product features high drag brake, no push brake, a 6V/5A BEC and a 27-turn brush motor limit. The recommended motor is Novak #3555 Fifty-Five Crawler 55-Turn. Use this product only in crawling applications where high drag brake and no push brakes are needed. Use in other applications or in higher load applications will void the warranty as stated in the main Rooster 12T instruction manual included with this product. THIS PRODUCT HAS A 27-TURN BRUSHED MOTOR LIMIT. USE WITH LOWER TURN MOTORS WILL VOID THE WARRANTY. ROOSTER CRAWLER THROTTLE PROFILES: Parameter W/ Reverse % Reverse Drag Brake Li-Po Cut-Off Profile 1 Yes 100 90% Disabled Profile 2 Yes 100 90% Enabled
2007 Novak Electronics, Inc. All Rights Reserved

www.teamnovak.com

L I - P O C U T - O F F C I R C U I T RY
The Rooster Crawler ESC has a built-in Novak Smart-Stop Li-Po Cut-Off Circuitry for safe, worry-free operation when using Lithium Polymer batteries. When the speed control is in Throttle Profile 2, the Smart-Stop Li-Po Cut-Off circuitry is active. The Smart-Stop Cut-Off circuitry constantly monitors the Li-Po batterys pack voltage. When the packs voltage begins to get close to the critical safety voltage, the Cut-Off circuitry will start interrupting, or blipping the throttle output. This blipping acts as an early warning to you that the battery voltage is getting low, and that the throttle output to the motor will soon be completely shut off. At this point, you should stop driving to save your battery from damage. When the battery packs critical safety voltage is finally reached, the SmartStop Cut-Off circuitry will completely shut down the throttle output signal to the motor to keep the battery voltage from dropping further (Red & Green LEDs will alternately flash--you will still have steering control). Re-charge battery pack after Smart-Stop circuitry shuts off throttle. After a short resting period, the batterys voltage will rise back above the critical safety voltage, and the ESC will operate normally again for a short period of time. This is not good for the battery pack, as reaching the critical safety voltage too many times can also cause damage to the cells. DO NOT CONTINUE TO RUN VEHICLE AFTER THE SMART-STOP HAS SHUT DOWN THE THROTTLE OUTPUT FOR THE FIRST TIME. If Throttle Profile 2 is used with Ni-Cd or Ni-MH type batteries, the cut-off circuitry will shut off the speed controls throttle output very early into the battery packs runtime, due to the different characteristics of these batteries Change ESCs Throttle Profile to Profile 1 for use with these batteries.
t r o u b l e - s h ootin g g u i d e
Red LED flashing: Speed control has thermally shut downAllow ESC to cool downUse milder motor or smaller pinion gearCheck for adequate cooling to ESCs heat sink. Red & Green LEDs alternately flashing: Smart-Stop Li-Po circuitry has shut off throttle outputUse a charged Li-Po battery. Using Ni-Cd or Ni-MH batteries with ESC in Profile 2change battery type or ESC Profile. Check motor connections. Check motor and brushes. Make sure ESC is plugged into the throttle channel of receiver. Check wiring color sequence of receiver signal harness (Refer to Step 1). Possible receiver damageCheck operation with a different receiver. Possible internal damageRefer to Service Procedures. Receiver or antenna too close to ESC, power wires, battery, or motor. Bad connectionsCheck wiring, connectors, & sensor harness. Motor capacitors broken or missingRefer to Step 3. Excessive current to motorUse a milder motor or a smaller pinion gear. External Power Capacitor damaged/not installedReplace Capacitor. Input harness and servo wires should be bundled separately. Power wires should be as short as possible. Check wires, receiver signal harness wiring & color sequence, radio system, crystals, battery/motor connectors, & battery pack. Possible receiver damageCheck operation with a different receiver. Possible internal damageRefer to Service Procedures. Gear ratio too lowIncrease gear ratio (smaller sized-pinion gear). If motor is damaged, try a different motor. Check battery connectorsReplace if needed. Incorrect ESC/transmitter adjustmentRefer to Step 4 & Transmitter Adjustments sections. External Power Capacitor damaged/not installedReplace Power Capacitor. Motor wired backwardsCheck wiring and reverse. Backwards motor timingReverse motor end bell. Internal damageRefer to Service Procedures.
Steering Channel Works But Motor Will Not Run
ROOSTER CRAWLER ESC INSTRUCTIONS

SPECIFICATIONS

Input Voltage. 4-7 cells (@1.2 volts DC/cell) / 2 Li-Po cells. Li-Po Cut-Off Voltage..6.25 volts DC. ESC Footprint.. 1.18 x 1.54 [30x39mm] ESC Weight (w/o wires)..1.57 ounce [44.5 grams] B.E.C. Rating...6.0 volts DC / 5.0 amps Power Wire (Battery/Motor). 14G Super-Flex Silicone Rated Current..400A Fwd / 200A Rev @25C trans.temp. On-Resistance.0.0014 Fwd / 0.0028 Rev @25C trans.temp. Motor Limit (single)..27 turn [@ 6 cells Ni-MH(1.2VDC/cell)] Motor Limit (dual).35 turn [@ 6 cells Ni-MH(1.2VDC/cell)] #55-1841-1 5-2008 Throttle Profiles..2 [1 with Li-Po Cut-Off] Switched Fan Output..6.0 volts DC

Recommended brushed motors for Rooster Crawler
Receiver Glitches/Throttle Stutters During Acceleration

Untidy Wires

Motor and Steering Servo Do Not Work
The Rooster Crawler Brushed speed control has crawler-specific throttle profiles, and is specially designed with builtin Smart-Stop Li-Po Cut-Off circuitry and a 6 volt / 5 amp BEC. The rugged ESC brings you 27-turn and higher motor handling, high-drag brake and is also the ideal partner for Novaks Forty-Five and Fifty-Five Crawler Brushed Motors.
The ESC also features Thermal Overload Protection, no Reverse Delay, Polar Drive & Digital Anti-Glitch circuitries for cool & smooth operation and Radio Priority circuitry for the ultimate in control, right down to the end of the charge. Add to this the user-replaceable power wires, power capacitor, & input harness, along with power output for auxiliary cooling fans that turn on & off with the ESCs power switch, and the Rooster Crawler-Edition has it all!
Attention crawler enthusiasts The Rooster has learned to crawl!
Speed Control Runs Excessively Hot
A u x i l ia r y F an C onnection
The Rooster Crawler ESC also features a set of power output pins for running auxiliary cooling fans. This allows you to add cooling fans to either the motor, the speed control, or both, and the best part is that they will automatically switch off when you turn off the speed controls power switch. These pins output 6.0 volts DC (the same as the BEC), so you will get maximum output from your cooling fans.
Model Runs Slowly/Slow Acceleration
Forty-Five Crawler (#3545) Fifty-Five Crawler (#3555)
To benefit from all of the technical features of the Rooster Crawler, PLEASE READ ALL INSTRUCTIONS

PRECAUTIONS

Always disconnect the battery pack from the speed control when not in use to avoid short circuits and possible fire hazard. Do not use a single motor that is lower than 27-turns. For dual motors for crawling, the motor range is 35 turns or above. A lower turn motor may damage ESC. Never allow water, moisture, or other foreign materials to get inside ESC, motor, or on the PC Boards. Water damage will void the warranty! Schottky diodes must NOT be used with the Rooster Crawler ESC. Schottky diode usage will damage ESC & void warranty! If using Ni-Cd or Ni-MH batteries, NEVER use fewer than 4 or more than 7 cells (4.8-8.4VDC, 1.2VDC/cell) in the vehicles main battery pack. If using Li-Po batteries, ONLY use a 2-cell pack for the vehicles main battery & be sure to use Profile 2 with the built-in Li-Po cut-off. Reverse battery polarity can damage ESC & void warranty. Disconnect battery immediately if a reverse connection occurs. An external power capacitor is installed and MUST be used with your ESC. Failure to use Power Capacitor will result in higher ESC operating temperatures & ESC damage. Always turn on the power of the transmitter first so that you will have control of the vehicle when you turn it on. Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits, which can damage ESC. Exposing the ESCs case to any type of solvents will damage the plastic. Exposure to CA glue or its fumes can cause damage to internal components of the speed control and result in premature failure.

OPTIONAL ACCESSORIES

The Rooster Crawler-Edition ESC comes with a factory-installed Power Capacitor, and it MUST BE USED to maintain cool and smooth operation. A direct replacement Power Capacitor is available in Novak kit #5682.
Note: We highly recommend using Novak Power Capacitors, as we have done extensive testing & research to find Power Capacitors with the very best quality factorsother capacitors with similar ratings will not provide equal protection.

Motor Runs Backwards

DISCONNECT BATTERIES WHEN NOT IN USE
REPLACEMENT POWER CAPACITOR [Novak kit #5682]
ESC Is Melted Or Burnt/ESC Runs With Switch Off
27-TURN SINGLE & 35-TURN DUAL MOTOR LIMIT! WATER & ELECTRONICS DONT MIX! NO SCHOTTKY DIODE!
*For more assistance call our Customer Service Department or check our Web site. positive fan pin negative fan pin

pin-out label

se r v ice p r oce d u r es
Before sending in your ESC for service, please review the Trouble-Shooting guide and instructions. Speed control may appear to have failed when other problems exist. After reviewing instructions, if you feel that your ESC requires service, please obtain the most current product service options and pricing by the following ways: WEB SITE: Print a copy of the PRODUCT SERVICE FORM from the CUSTOMER SERVICE section of the Novak Web site. Fill out the needed information on this form and return it with the Novak product that requires servicing. PHONE/FAX: If you do not have access to the internet, please contact our customer service department by phone or fax as listed below. WARRANTY SERVICE: For warranty service, you MUST CLAIM WARRANTY on the PRODUCT SERVICE FORM and include a valid cash register receipt with purchase date and dealer name & phone# on it, or an invoice from previous service. If warranty provisions have been voided, there will be service charges. ESCs returned without a serial number will not be serviced under warranty ADDITIONAL NOTES: Units that operate normally will have a service charge. Dealers/distributors are not authorized to replace Novak products thought to be defective. If a hobby dealer returns your product for service, submit a completed PRODUCT SERVICE FORM to the dealer and make sure it is included with the product. Novak does not make any internal electronic components available for sale.

Novak Super-Flex wire for power wiring. 14 gauge silicone wire in kit #5514 (36black, 36red, & 36blue). User-replaceable input signal harness is available in both short and long lengths. 4.5 harness in Novak kit#5315, and 9.0 harness in Novak kit #5320. Additional motor capacitors are available in Novak kit #5620. The Rooster Crawler comes with power output pins ready to add a cooling fan that will switch on & off with the ESCs power switch. Novak 25x25x10mm fan with long leads for cooling motor is available in Novak kit #5647. Novak 30x30x6mm clear fan that fits perfect over the ESCs heat sink and has a connector already on its leads is available in Novak kit #5648.
SUPER-FLEX SILICONE 14G WIRE [Novak kit #5514] INPUT SIGNAL HARNESS [Novak kits #5315 & 5320] MOTOR CAPACITORS [Novak kit #5620]
The Roosters pin-out label located on the front lower section of the ESCs case (under the pins, push button, & LEDs) shows the location and the polarity of the fan power output pins. They are the 2 pins on the front edge of the circuit board--Positive (+) is on the left, and Negative () is on the right. The set of 3 pins behind them are for the user-replaceable input signal harness, and the polarity of those is the same--Positive in the middle, Negative on the right, and the extra pin on the left is signal. The Novak 30x30x6mm clear cooling fan that comes on the GTB speed control (Novak kit #5648) not only fits the size of the Rooster Crawlers heat sink perfectly, it also comes with the connector already on it for directly plugging in. Fans that do not have the proper connector on them, will need a connector (one end of an old receiver input harness would work well), or will need to be soldered to the pins--Take extra care if attempting to solder to the fan power output pins--Do not overheat the pins or the circuit board, and do not allow any solder or wire strands to cause a short circuit with other pins or the heat sink.
4 TO 7 CELLS OR 2-CELL Li-Po ONLY
AUXILIARY COOLING FANS [Novak kits #5647 & #5648]

NO REVERSE VOLTAGE!

POWER CAPACITOR REQUIRED
TRANSMITTER ON FIRST INSULATE WIRES NO SOLVENTS NO CA GLUE

Novak Electronics, Inc.

(949) 833-8873 FAX (949) 833-1631 Customer Service e-mail: cs@teamnovak.com Monday-Friday: 8:00am-5:00pm (PST)
The Rooster Crawler ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). Warranty does not cover incorrect installation, components worn by use, damage to case or exposed circuit boards, damage from using fewer than 4 or more than 7 Ni-Cd or Ni-MH cells (1.2 volts DC/cell) or fewer or more than 2 Li-Po cells input voltage, crossconnection of battery/motor power wires, overheating solder tabs, reverse voltage application, damage resulting from thermal overload, damage from incorrect installation of FET servo or receiver battery pack, not using or incorrect installation of a Power Capacitor on ESC or from using a damaged Power Capacitor, using a Schottky diode, using non-Novak Power Capacitor, splices to input or ON/OFF switch harnesses, damage from excessive force when using the One-Touch/SET button or from disassembling case, tampering with internal electronics, allowing water, moisture, or any other foreign material to enter ESC or get onto the PC board, incorrect installation/wiring of motor/battery connectors, input plug plastic, or auxiliary cooling fan, allowing exposed wiring, pins, or solder tabs to short-circuit, or any damage caused by a crash, flooding or natural disaster. Because Novak Electronics, Inc. has no control over the connection & use of the speed control or other related electronics, no liability may be assumed nor will be accepted for any damage resulting from the use of this product, including battery packs. Every Novak speed control & motor is thoroughly tested & cycled before leaving our facility and is, therefore, considered operational. By the act of connecting/operating speed control, user accepts all resulting liability. In no case shall our liability exceed the products original cost. We reserve the right to modify warranty provisions without notice. 2008 Novak Electronics, Inc. All Rights Reserved No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. Rooster Crawler ESC, Polar Drive Technology, Radio Priority Circuitry, & One-Touch Set-Up are all trademarks of Novak Electronics, Inc. All Novak speed controls are designed & assembled in Irvine, CA, and are Lead-Free & RoHS compliant.

p r o d u ct w a r r ant y

S T E P 1 connect

inp u T Ha r ness

S T E P 3 m oto r

1.INSTALL MOTOR CAPACITORS
& b atte r y connection
3.FACTORY-INSTALLED POWER CAPACITOR REQUIRED
The ESC comes with a factory-installed Power Capacitor, and it MUST be
S T E P 4 one - to u c h p r o g r a m m in g
With ESC connected to (at least) a receiver & a charged battery pack: 1. TURN ON THE TRANSMITTERS POWER 2. PRESS & HOLD ESCS ONE-TOUCH/SET BUTTON 3. TURN ON THE SPEED CONTROLS POWER With transmitter throttle at neutral, and still pressing the SET button, slide the ESCs ON/OFF switch to ON position. 4. CONTINUE HOLDING SET BUTTON UNTIL RED LED COMES ON 5. RELEASE SET BUTTON AS SOON AS LED TURNS RED 6. PULL TRANSMITTER THROTTLE TO FULL-ON POSITION Hold it there until the green status LED turns solid green. Note: Motor will not run during programming even if connected. 7. PUSH TRANSMITTER THROTTLE TO FULL-BRAKES Hold it there until the green status LED blinks green. 8. RETURN TRANSMITTER THROTTLE TO NEUTRAL Red status LED will turn solid red, indicating that speed control is at neutral and that proper programming has been completed. NOTE: If transmitter settings are changed, One-Touch Programming must be repeated. If you experience any problems, turn off ESC & repeat One-Touch.
REMEMBER: Whenever One-Touch set-up is performed, ESC automatically reverts to Throttle Profile #1.
The Rooster Crawler Brushed ESC has the industry-standard receiver input connector on a user-replaceable input harness & works with all major radio brands new receivers. However, some very old receivers must have the wiring sequence in the plastic 3-pin connector housing changed. This is important, because receiver & servo electronics may be damaged if the sequence is incorrect.
Electric motors generate RF noise that causes interference. The included 0.1F (50V) non-polarized, ceramic capacitors must be used on all motors to reduce motor noise & prevent ESC damage. Novaks Forty-Five and Fifty-Five Crawler Brushed Motors have the required capacitors factory installed.
used for proper operation and protection.

If Power Cap. becomes dented or damaged, ESC failure will occur--replace immediately. Longer Power Capacitor wires will decrease performance.
C h an g in g w i r in g se q u ence @ r ecei v e r
JR, Hitec, Futaba, new KO, & Airtronics Z receivers do not need input harness re-wiring. Airtronics Z receivers have blue plastic cases & new KO cases have tabs on the input harness openings as in Figure 1. Plug one end of the input signal harness into the THROTTLE CHANNEL (#2) of receiver with the BLACK wire toward the outside edge of receiver case. Plug the other end of the input harness into 3-pin header on the front edge of the ESCs circuit board with the WHITE wire toward the left side of the ESC (refer to pin-out label on case).
JR Hitec Futaba New KO Airtronics Z
Note: Some motors come with capacitors built-in. If your motor only has two capacitors, you need to install a capacitor between the positive & negative motor tabsIf you experience radio interference when using only built-in capacitors, install external ones.
4.SOLDER MOTOR POWER WIRES TO MOTOR
Solder 0.1F (50V) capacitors between:
a. Cut the ESCs BLUE & YELLOW silicone motor power wires to the desired length, and strip 1/8-1/4 of insulation from the end of each wire. Tightly twist the exposed strands of wire. Tin the wire ends with solder. b. Solder the ESCs BLUE motor wire to the motors negative () tab. c. Solder the ESCs YELLOW motor wire to the motors positive (+) tab. Connect the ESCs Tamiya-style JST battery connector to a charged 4 to 7 cell (1.2VDC/cell) battery pack (or 2-cell Li-Po pack). The connector can also be changed to a different type, or the ESC can be hard-soldered directly to the battery pack.
POSITIVE (+) motor tab & NEGATIVE () motor tab. POSITIVE (+) motor tab & GROUND tab*. NEGATIVE () motor tab & GROUND tab*. *If motor has no ground tab (below), solder the capacitors to motor can. Negative (-) motor tab **NO SCHOTTKY DIODE** 0.1F Capacitors Positive (+) motor tab Ground / motor can
5.CONNECT SPEED CONTROL TO BATTERY PACK

FIGURE 1

FIGURE 2
New KO (with tabs) tabs white red black
Old KO (no tabs) no tabs white black red

FIGURE 4

C onnecto r u sa g e
If you are going to use connectors on the ESCs motor wires, we highly suggest Deans Ultra plugs or Novaks low-loss connectors--do not use crimp type connectors. Note: If you plan to change the battery connector, be aware that this can void the warranty if not done properly. To prevent possible cross-connection of motor and battery wires: Use connectors that cannot be plugged in backwards. Reverse voltage will damage the ESC and void warranty. Use a female connector on battery packs to avoid shorting. For additional information on Novak connectors & their usage, visit our Web site.

R O O S T E R C R A WL E R set - u p P h oto
If you have an older KO or Sanwa/Airtronics, you must change the sequence of the ESCs input harness wires--Old Sanwa/Airtronics cases are black color & Old KO cases do not have tab openings, as in Figure 2 above. Using a small flat blade screwdriver, remove the red & black wires from the plastic housing at the receiver end of the input harness as in Figure 3 below. Interchange the red and black wires in the plastic 3-pin connector housing at the receiver end of the input harness. Insert modified end of the harness into the THROTTLE CHANNEL (#2) of receiver with the RED wire toward the outside edge of receiver case. Plug the other end of the input harness into the ESC with the WHITE wire toward the S (signal) marking on the ESCs case.
Old-style KO Old-style Sanwa/Airtronics
Extra 0.1F capacitors are available in Novak kit #5620.
2.DO NOT USE SCHOTTKY DIODES
t r ans m itte r a d j u st m ents
NOT ALL TRANSMITTERS HAVE THESE ADJUSTMENTS
Schottky diodes must NOT be used with reversible ESCs (including brushless). Schottky diode usage will damage the ESC & void warranty.
Trail excess wire off top of antenna mast Tamiya-style battery connector
Battery Pack NiMH: 4 to 7 cell pack Li-Po: 2S pack*
FIGURE 3 With a small standard screwdriver, gently lift plastic prong until wire and metal socket easily slide out of plastic housing.
Red power wire (battery positive) Black power wire (battery negative)
*If using Li-Po batteries, be sure to select Throttle Profile 2 so that Li-Po Cut-Off Circuitry is enabled.
If you have any problems with Step 4, adjust transmitter as follows and then repeat One-Touch programming in Step 4: A.Set HIGH ATV or EPA to maximum setting. [amount of throw at full throttle] B.Set LOW ATV, EPA, or ATL to maximum setting. [amount of throw at full brakes] C.Set EXPONENTIAL to zero setting. [throttle channel linearity] D.Set THROTTLE CHANNEL REV. SWITCH to opposite position. E. Set THROTTLE CHANNEL TRIM to middle setting. [adjusts neutral position/increases or decreases coast brakes] F. Set ELECTRONIC TRIGGER THROW ADJUSTMENT to 50% throttle and 50% brake throw--best for reversible ESCs. [adjusts trigger throw electronic/digital pistol-grip transmitters] G.Set MECHANICAL TRIGGER THROW ADJUSTMENT to position with 1/2 throttle and 1/2 brake throw.
Power Capacitor tie-wrapped along power wires Servo plugged into steering ch. (#1)

ON/OFF switch

tH r ott l e P r o F i l e S e l ection
Blue power wire (motor negative) 27-turn or higher brush-type motor
The Rooster Crawler is equipped with 2 user-selectable Throttle Profiles:
Parameter Li-Po Cut-Off (see next page) W/ Reverse Drag Brake

PROFILE 1 Disabled Yes (100%) 90%
PROFILE 2 Enabled Yes (100%) 90%

Rooster Crawler ESC

S T E P 2 m o u ntin g
Be sure to position the ESC with the power wires away from other electronics & moving parts in the vehicle. Select a location that allows airflow through heat sinks--If the ESC gets good air flow, it will run cooler; and that means it will be more efficient! 1. MOUNT ESC IN THE VEHICLE using the included double-sided tape. Be sure receiver & antenna are mounted as far from ESC, power wires, battery, & servo as possible--these components all emit RF noise when throttle is applied. On graphite or aluminum chassis vehicles, it may help to place receiver on edge with crystal & antenna as far above chassis as possible.
Note: Mount antenna as close to receiver as possible--trail any excess wire off top of antenna mast (cutting or coiling excess antenna wire will reduce radio range).
User-replaceable input signal harness (Ch.2) Status LEDs One-Touch Set-Up button
NOTE: ESC is factory set to Throttle Profile #1.
Yellow power wire (motor positive) Novak #3555 Fifty-Five Crawler Brushed Motor Shown
selecting throttle profile :
Usin g a r ecei v e r Batte r y P ac k
The Rooster Crawler has a built-in BEC (battery eliminator circuit), and you do not need to use a separate receiver battery pack, however if you are planning to use one to power the electronics you need to do the following: 1. Plug the external 5 cell (1.2VDC/cell) receiver battery pack into the battery slot of the receiver. 2. Leave the ESCs ON/OFF switch in the OFF position, and use receiver battery packs ON/OFF switch to turn the system power on and offDo not use the ESCs switch.
2. MOUNT POWER CAPACITOR IN THE VEHICLE using the included double-sided tape, or secure it to part of the vehicle with a tie-wrap. The Power Capacitor can also be tie-wrapped along the battery power wires. If the Power Capacitor becomes dented or damaged, ESC failure will occur--replace damaged Power Capacitors immediately. 3. INSTALL ON/OFF SWITCH using a screw or the included double-sided tape. Position in the vehicle where it will be easy to access.
With ESC on & connected to a charged battery (transmitter ON or OFF): 1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER To avoid possible radio interference from other transmitters, remove the ESCs input signal harness from the receiver. 2. PRESS & HOLD THE ESCS ONE-TOUCH SET BUTTON Continue to hold SET button on ESC until both LEDs turn on. 3. RELEASE SET BUTTON AS SOON AS BOTH LEDs COME ON Once released, the 2 status LEDs will flash to indicate what Throttle Profile is currently selected. The number of times the LEDs flash indicates the Throttle Profile selection (1 of 2). 4. QUICK PRESS (& release) SET BUTTON TO CHANGE SELECTION Each press will change to the next consecutive Throttle Profile.

*** Note: there is a time constraint during this selection process. ***

www.teamnovak.com

5. ESC STORES SELECTION & EXITS TO NEUTRAL If SET button is not pressed for 3 sec., ESC stores selected Profile into memory & the red LED will come on solid. The speed control is at neutral & is ready to go. P3
NOTE: Whenever One-Touch set-up is performed, ESC reverts to Throttle Profile #1.