Position the document to be copied.
For details on positioning the document, refer to "Feeding the document" on page 2-27.
In the Basic screen, touch [Separate Scan].
To cancel the "Separate Scan" setting, touch [Separate Scan] again to deselect it.
Press the [Start] key. After the document has been scanned, the following message appears.
If the "Separate Scan Output Method" parameter is set to "Batch Print", touch [Finish] in the following screen, which appears while the document is scanned with the ADF, to continue to step 5.
Load the next batch of the document, and then press the [Start] key. Repeat step 2 until all document pages have been scanned. If the document cannot be loaded into the ADF, place it on the original glass. For details on the types of documents that can be loaded into the ADF, refer to "Original documents" on page 2-96. To change the scanning settings, touch [Change Setting].

Copy Operations

The buttons that appear in the screen for changing the settings differ depending on the specified settings. Settings for the following can be changed. 1-Sided/2-Sided, Binding Position, Zoom, Frame Erase, Center Erase Original Size To cancel changes to the settings, touch [Cancel].
The amount of memory available can be checked beside "Memory" in the lower-left corner of the screen. To delete the image data, press the [Stop] key, and then delete the job. For details, refer to "Temporarily stopping scanning/printing" on page 2-69.
After all document pages have been scanned, touch [Finish].
Press the [Start] key. If the "Separate Scan Output Method" parameter is set to "Batch Print", touch [Print] or press the [Start] key.
Copy Operations If the "Separate Scan Output Method" parameter is set to "Batch Print", the copy settings can be changed. To change the copy settings, touch [Change Setting], and then touch [OK] after changing the settings as desired.
Scanning a multi-page document from the original glass When making double-sided or combined copies using the original glass, place each page of a multi-page document on the original glass to scan it. The following procedure describes how to place single-sided document pages on the original glass to make double-sided copies. 0 The output method used with the "Separate Scan" setting can be set to "Page Print" or "Batch Print". As a default, "Page Print" is selected. Lift open the ADF. Position the first page or the first side of the document face down onto the original glass. For details on positioning the document, refer to "Placing the document on the original glass" on page 2-28.

Copy Operations For a document that contains photos, touch [Photo] to display the Photo Type screen. Touch the button for the appropriate setting, and then touch [OK].
For a document that contains maps, touch [Map]. For a document that contains faint text, touch [Dot Matrix Original]. For a document printed with this machine, touch [Copied Paper].
The Quality/Density screen appears again.
Selecting finishing settings
Various settings can be selected for sorting and finishing copies fed into the copy output tray.
As the factory default, "Group" is selected.
If no finisher is installed and all of the following conditions are met, printed copies are fed out and sorted in an alternating crisscross pattern. A4- or B5-size paper is used. Paper of the same size and type is loaded with the w orientation in one paper tray and with the v orientation in another tray. The "Auto" Paper setting is selected. The "Auto" Paper setting is not selected when the "Mixed Original" setting is selected.
From Administrator Settings mode, the machine can be set so that copies are fed out without being shifted when the finisher is installed. As a factory default, the machine is set to shift the copies that are fed out. For details on "Fold/Bind" and Center Staple / Fold, refer to "Selecting a folding setting" on page 2-61.
The following Finishing settings are available.
Setting Sort Description Select this setting to separate each set of a multi-page document.
Select this setting to separate the copies of each page in a multi-page document.
Setting Offset Description
If no finisher is installed If the sorting conditions are met, printed copies are fed out and sorted in an alternating crisscross pattern.
If a finisher is installed The copies are fed out and stacked on top of each other with each set shifted to separate it.

Fold/Bind

Select one of these settings to fold copies. The copies can also be bound with staples at the same time.

Single-sided documents Document paper type/Weight Document size Paper capacity Plain paper: 35 g/m2 to 210 g/m2 Double-sided documents Plain paper: 50 g/m2 to 128 g/m2
A3 w to B6 w, A6 w,11 e 17 w, 11 e 15 w, 8 e 13 w, 8-1/2 e 11 w/v 100 sheets (80 g/m2)
For documents of mixed sizes
Single-sided documents Document paper type/Weight Document size Paper capacity Plain paper: 50 g/m2 to 128 g/m2 Refer to "Mixed originals paper sizes". 100 sheets (80 g/m2) Double-sided documents
Mixed originals paper sizes The following chart shows the possible combinations of standard-sized paper that can be used with the "Mixed Original" setting.
Maximum Document Width*1 Document Size*2 A3 w A4 v B4 w B5 v A4 w A5 v B5 w A5 w o o o o o e e e o o o o o e e e e e o o o o o e e e o o o o o e e e e e o o o e e e e e o o o e e e e e e e o o e e e e e e e o A3 w A4 v B4 w B5 v A4 w A5 v B5 w A5 w
o available e not available

*1Indicates the width

of the widest document size of the mixed originals (width of the adjustable lateral guides of the automatic document feeder). document sizes that can be specified together with the maximum document width.

*2Indicates

Copy Operations Precautions for loading documents into the ADF
The following types of documents should not be loaded into the ADF, otherwise paper misfeeds or damage to the document may occur. Wrinkled, folded, curled, or torn documents Highly translucent or transparent documents, such as OHP transparencies or diazo photosensitive paper Coated documents such as carbon-backed paper Documents printed on paper thicker than 210 g/m2 Documents printed on paper thicker than 128 g/m2 during double-sided printing Documents that are bound, for example, with staples or paper clips Documents that are bound in a book or booklet Documents with pages bound together with glue Documents with pages that have had cutouts removed or are cutouts Label sheets Offset printing masters Documents with binder holes Documents that have just been printed with this machine
Before loading folded documents, such as those folded in half or in a zigzag, into the ADF, be sure to flatten the pages.
Documents that can be placed on the original glass To copy documents that cannot be loaded into the ADF, position them on the original glass.
Original glass documents Document types Document sizes Maximum weight Sheets, books (page spreads), three-dimensional objects A3 w to B6 w, A6 w 11 e 17 w to 5-1/2 e 8-1/2 w/v, 8K, 16K v/w 2 kg
Precautions for positioning documents on the original glass Observe the following precautions when placing the document on the original glass. If a document of non-standard paper size is loaded, the "Auto" Paper setting and "Auto" Zoom setting cannot be used since the document size cannot be detected automatically. If a document of a non-standard paper size is loaded, select the paper drawer and zoom ratio or touch [Original Setting] and select the document size. If highly translucent or transparent documents, such as OHP transparencies or diazo photosensitive paper, are loaded, the document size cannot be detected automatically. Place a blank sheet of paper of the same size over the document. Do not place objects exceeding 2 kg on the original glass, otherwise the original glass may be damaged. Do not press down extremely hard on a book spread on the original glass, otherwise the original glass may be damaged.

Touch [OK], and then touch [OK] in the next screen that appears. Specify any other desired copy settings. Using the keypad, type in the desired number of copies.
Place the document to be inserted on the original glass. For details on positioning the document, refer to "Feeding the document" on page 2-27.
Press the [Start] key. Scanning begins. Touch [Finish].
To insert a multi-page document, repeat steps 9 and 10 until all pages of the insertion document are scanned in the order that they are to be inserted.
Specifying pages to be printed on the front side ("Chapters" function)
When making double-sided copies, the pages specified as the first page of a chapter can be printed on the front side of the paper. If the document was arranged so that the specified page would be printed on the back side of a page, the page is left blank and the specified page is printed on the front side of the next page. In addition, the specified page can be printed on different paper.
A maximum of 30 pages can be specified to be printed on the front side of the paper within a document of up to 999 pages. In double-sided documents, one double-sided page is considered to be two pages (one for the front and one for the back).
Make sure that the paper loaded for the first page of the chapter and for the copy have the same size and orientation.

Touch [Chapters].

The Chapter screen (for editing) appears.
Using the keypad, specify the first page of the chapters.
There are two Chapter screens. Touch and to display a different screen. To arrange the page numbers in order, starting with the lowest number, touch [Sort]. To remove a page number that has been specified, touch the button for the page to be removed, and then press the [C] (clear) key. Under "Original > Copy", select "1-Sided > 2-Sided". If the same page number is entered multiple times, copying is not possible. Delete repeated page numbers. If the specified page number is greater than the number of pages in the document, that page number is ignored.
Under "Chapter Paper", touch [Copy Insert] or [None]. If "None" is selected, all pages of the copy are printed on the same paper. To cancel the setting and select the default, press the [Reset] key. To cancel the "Chapters" function, touch [No].
If "Copy Insert" is selected, [Chapter Paper] appears. Touch [Chapter Paper], select the paper to be used for the first page of the chapter, and then touch [OK].

Producing separate copies of each page in a page spread ("Book Copy" function)
An open book or catalog can be copied with the left and right pages on separate sheets of paper. The following copy methods are available, and there are settings for adding front and back covers.
Setting Book Spread Separation Front Cover Front and Back Cover Description Both pages of the page spread are printed on the same page. Separate copies of each page in the page spread are printed in the document page order. The document is scanned to fit the size of paper that will be used. The front cover and separate copies of each page in the page spreads are printed in the document page order. The front cover, separate copies of each page in the page spreads and the back cover are printed in the document page order.
Place the document on the original glass. Place the pages on the original glass, starting with the first page. For details on positioning the document, refer to "Feeding the document" on page 2-27. If "Front and Back Cover" was selected, the front cover is scanned before the back cover, and then all page spreads are scanned in order.
How are the front and back covers copied? % Scan the front cover, then the back cover, and then scan the remainder of the document.
Load the paper to be used into the desired paper tray.
Touch [Application], and then touch [Book Copy/Repeat]. To cancel changes to the settings for all Application functions, press the [Reset] key. All changes to the settings are canceled.
The Book Copy/Repeat screen appears.

Touch [Book Copy].

[Booklet Original] does not appear if the optional finisher is not installed. The Book Copy screen appears.
Touch the button for the desired setting.
If "Separation", "Front Cover" or "Front and Back Cover" is selected, [Binding Position] appears. Select the binding position of the document. If desired, specify a Book Erase function. Touch the button for the erasing method, touch [-] and [+] to specify the width of the area to be erased, and then touch "OK". When using the keypad to specify the settings, press the [C] (clear) key to erase the value, and then type in the setting.
To cancel the "Book Copy" function, touch [No].

First-level menu [3] Administrator Settings
[4] Check Consumable Life [6] Banner Printing (d-Color MF450)
Print List Allow Restrict
Setting up the PCL driver for Windows
Common settings The following describes the common settings and buttons that are displayed on all tabs.
Button OK Cancel Help Add (Favorite Setting) Edit (Favorite Setting) Default View
Function Click this button to close the dialog box and apply any settings that have been changed. Click this button to cancel any settings that have been changed and close the dialog box. Click this button to display the help for each item on the currently displayed dialog box. Click this button to save the current settings and to view them at a later time. Click this button to change the saved settings. Click this button to return the settings to their defaults, which were selected when the driver was installed. When the [Paper View] button is clicked, a preview of the page layout as specified in the current settings is displayed and a preview image of the print job can be checked. When the [Printer View] button is clicked, a printer figure is displayed showing any options, such as the paper tray, that are installed on this machine.

Printer

To enable any installed options, you must specify the Device Option settings.

Basic tab

Item Original Orientation Original Size Paper Size Zoom Paper Tray Paper Type Output Method [User Settings] [Authentication/Account Track] Function Specifies the orientation of the original document. Specifies the size of the original document.
Specifies the output paper size. Automatically enlarges or reduces when the Original Size setting is changed. Specifies the enlargement and reduction ratio. Selects the paper tray for printing. Selects the paper type for printing. For non-conventional printing, selects special output methods such as "Secure Print" or "Save in User Box". Specifies the ID and password, or the file name and box number when performing "Secure Print" or "Save in User Box". Specifies the user name and password when performing user authentication, and the department name and password when performing account track on this machine. Specifies the number of copies to print. Specifies whether to print multiple copies in sets. When printing multiple copies, shifts the output position of each set. Specifies the paper type for each paper tray.

Click the Layout tab. Select the "Chapter" check box. Enter the page number of the page you want to print on the front side.
When entering multiple page numbers, separate the page numbers with commas such as "2, 4, 6" or enter a page range using a hyphen such as "6-10". The "Chapter" check box can only be selected when the duplex printing or the booklet printing setting is enabled.
Specifying duplex/booklet printing You can print a document onto both sides of a page or in a booklet format (two facing pages). This comes in handy when you want to bind multiple-page documents.
Click the Layout tab. From the "Print Type" drop-down list, select "2-Sided" or "Booklet".
The binding position can be specified from the "Binding Direction" drop-down list.
Setting the binding margin Binding margins are added to the document before it is printed.
Click the Layout tab. From the "Binding Direction" drop-down list, select the binding position. Select the "Binding Margin" check box.
Print Operations To set the width of the binding margin, click the [Binding Margin Settings] button, and then specify the desired settings in the Binding Margin Settings dialog box that appears. Shift Mode: To add a binding margin, select how the image is to be shifted. Front Side/Back Side: Sets the binding margin values. By clearing the "Same value for front and back sides" check box, you can specify separate values for the front and back sides. Unit: Selects the measurement unit that specifies the size.
Shifting images The entire print image of a document is shifted and then printed. You can use this function when you want to adjust the print position.
Click the Layout tab. Select the "Image Shift" check box. To set the image shift settings, click the [Image Shift Settings] button, and then specify the desired settings in the Image Shift Settings dialog box that appears. Unit: Selects the measurement unit that specifies the size. Front Side/Back Side: Specifies the shift direction and sets the values. By clearing the "Same value for Front and Back sides" check box, you can set separate values for the front and back sides.
Specifying the finish tab settings (PCL driver for Windows)

When sending a fax, click the [Add From Phone Book] button in the Fax Transmission Popup dialog box. To open the Fax Transmission Popup dialog box, follow steps 1 to 5 under "Fax operations". For details, refer to "Fax operations" on page 3-75.
Select "Personal List" or "Group" from the list on the left side of the dialog box to display the desired recipient in "Personal Information". Click the [Find] button to specify the conditions to search for a recipient.
Select the name of the recipient you want to send a fax to, and then click the [Add Recipients] button. Multiple recipients can be added in the same way. Up to 100 recipients can be added. To delete a recipient, click the [Delete] button.
Print Operations If recipients have been added to a group, all the members of the group can be added to "Recipient List" (group transmission) by selecting a group name, then clicking the [Add Recipients] button.
Click the [OK] button. The names that were specified are added to "Recipient List" and the Fax Transmission Popup dialog box appears again.
Specifying the transmission settings When sending a fax, you can specify the transmission settings in the Fax Mode Details dialog box that appears when the [Fax Mode Setting Details] button is clicked in the Fax Transmission Popup dialog box.
Print Recipient File: Prints the document after a fax was sent. Timer Send: Sets the transmission time. By clicking the [Reflect Current Time] button, the current time set on the computer is displayed in the "Send Time" boxes. SUB Address: Specifies the sub address for sending confidential faxes using F-codes. Sender ID: Specifies the sender ID for sending confidential faxes using F-codes.
When using Timer Send, check that the time set on the computer is synchronized with the time on this machine. If the transmission time is earlier than the current time of this machine, the fax is sent the next day. If sending confidential faxes using F-codes to another fax model, enter the sub address and sender ID in the "SUB Address" and the "Sender ID" text boxes. Up to 20 characters (numbers 0 through 9) can be entered in the "Sub Address" text box. Up to 20 characters (numbers 0 through 9, #, and *) can be entered in the "Sender ID" text box.

Touch [OK]. Touch [File Path], and then type in the file path, using the keyboard that appears. Touch [OK]. Touch or.
Touch [User ID], and then type in the user ID, using the keyboard that appears. To cancel registration of the user ID, touch [ON] beside "anonymous".
Touch [OK]. Touch [Password], and then type in the password, using the keyboard that appears. Touch [OK].
Network Scanner Operations If necessary, specify settings for "anonymous", "PASV mode", "Proxy" and "Port Number". To enter a port number, press the [C] (clear) key to clear the current value, and then use the keypad to type in the port number. If a value outside the allowable range is specified, the message "Input error" appears. Type a value within the allowable range.
Touch [OK]. The FTP destination is registered.
The registration cannot be completed if no settings are specified for "Name", "Host Address", "File Path", "User ID" and "Password". To cancel the registration, touch [Cancel]. To finish specifying settings in the Utility mode, press the [Utility/Counter] key. Otherwise, exit the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax/Scan or Box mode appears.
Registering a group destination
A group destination can be registered.
Up to 100 groups can be registered, and up to 500 destinations can be registered in a single group.
Touch [2 Create Group] in the Create One-Touch Destination screen. The Group screen appears.
Touch [OK]. Touch [Select Group].
Network Scanner Operations Select a destination type, and then select the destination to be registered.
Touch [OK]. Touch [Close]. Touch [OK]. The Group destination is registered.
The registration cannot be completed if no settings are specified for "Name" and "Destination". To cancel the registration, touch [Cancel]. To finish specifying settings in the Utility mode, press the [Utility/Counter] key. Otherwise, exit the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax/Scan or Box mode appears.
The User mode provides functions for checking and operating the machine on a user level. You can select from five tabs (Information, Job, Box, Direct Print, and Store Address). This section contains descriptions of the items in the menu that appears on the left side of the page when each User mode tab is clicked.

Information tab

On the Information tab, information and settings concerning the system configuration of the machine are displayed. Device Information - Configuration Summary The system configuration and status of the machine are displayed. This is the first page that appears when the machine is accessed with Web Connection.
Item Device Information Paper Tray Output Tray Administrator Information

If user authentication settings have specified on the machine, "Change User Password" appears in the menu. The user password can be changed when "User Authentication" is set to "ON (MFP)".
If "Password Rules" is set to "Enable", only a password containing 8 digits can be specified. If a user password containing less than 8 characters has already been registered, change the password so that it contains 8 characters before setting "Password Rules" to "Enable".
Function Permission Information Information on operations permitted by users and accounts can be displayed.
Item Function Permission* Output Permission (Print/TX) Upper Limit Management *
Description Displays whether or not each machine operation can be used. Displays whether or not each machine output operation can be used. Displays the maximum limits and current counter values.
This is only displayed in user registration information.
If user authentication and account track settings have been specified on the machine, "Function Permission Information" appears in the menu. If user authentication or account track settings have not been specified, only the specified function permissions are displayed.

6-8 d-Color MF550/MF450

Web Connection Operations Network Setting Information Network settings for the machine can be displayed.
Item Protocol Information Network Information
Description Displays the usage status for each protocol. Displays information about the network.
Print Setting Information Settings for the printer controller of the machine can be displayed. A print job sent with no settings specified is printed with these settings.
The following information can be selected from the submenu.
Item Default Setting Font Information Macro List PCL Setting PS Setting Description Displays information for each of the items.
Print Information % Font and settings information can be printed. Select the report to be printed, select a paper tray from the "Paper Tray" list, and then click the [OK] button.
Item PS Font List PCL Font List GDI Demo Page Configuration Page Paper Tray
Description Prints the list of fonts that can be used with PostScript. Prints the list of fonts that can be used with PCL. Prints the GDI demo page. Prints the list of print settings specified for the machine. Select the paper tray loaded with the paper used for printing the reports.

Select the display level for the destination. If "Search from Reference Allowed Group" is selected, click the [Search from List] button, and then select an access permission group from the list. If "Set direct Reference Allowed Level" is selected, select a level. Type in the e-mail address of the destination (up to 320 characters). Select this check box to register certificate information. Select "Registration of Certification Information". Click the [Browse] button, and then specify the certificate information. Only files in the DER (Distinguished Encoding Rules) format are supported for certificate information. To delete the certificate information, select "Deletion of Certification Information".
E-mail Address Registration of Certification Information
If "FTP" was selected
Item Name Index Limiting Access to Destinations Description Type in the name of the destination (up to 24 characters). Select the index characters for the destination. To normally display the destination in the touch panel, check the "Main" check box. Select the display level for the destination. If "Search from Reference Allowed Group" is selected, click the [Search from List] button, and then select an access permission group from the list. If "Set direct Reference Allowed Level" is selected, select a level. Type in the IP address or host name for the FTP server to be used for transmitting (up to 63 characters). To type in the host name, check the "Please check to enter host name." check box. If the machine is set to use IPv6, an IPv6 address can also be specified. Type in the destination file path (up to 96 characters). Type in the user ID (up to 47 characters). Type in the password (up to 31 characters). Select either "ON" or "OFF". Select either "ON" or "OFF". Select either "ON" or "OFF". Type in the port number. (Range: 1 to 65535; Default: 21)

Host Address

File Path User ID Password anonymous PASV Mode Proxy Port No.
If "SMB" was selected
Item Name Index Limiting Access to Destinations Description Type in the name of the destination (up to 24 characters). Select the index characters for the destination. To normally display the destination in the touch panel, check the "Main" check box. Select the display level for the destination. If "Search from Reference Allowed Group" is selected, click the [Search from List] button, and then select an access permission group from the list. If "Set direct Reference Allowed Level" is selected, select a level. Type in the IP address or host name for the destination computer (up to 255 characters; host name in uppercase letters). To type in the host name, check the "Please check to enter host name." check box. If the machine is set to use IPv6, an IPv6 address can also be specified. Type in the destination file path (up to 255 characters, uppercase letters). Type in the user ID for the destination computer (up to 127 characters). Type in the password for the destination computer (up to 14 characters).

Specifying from registered destinations When an Address Book has been registered, you can search for the destination by the registered search word and dial the destination.
Refer to "Searching for a registered destination (Index button)" on page 7-13 regarding registered destination search methods used by touching the Index button. Refer to "Searching for a registered destination (Address type)" on page 7-13 regarding searching by destination type. Refer to "Searching for registered destinations (Detail search)" on page 7-14 regarding entering details to conduct searches.
% Touch the desired destination button displayed in the [Address Book] tab. To cancel a selected destination, re-select the destination you wish to cancel. If [Reset] key is pressed, the selected address and the settings are cleared. When desired destination button is not displayed, it can be searched for using the following methods. Touch the Index button Search by destination type Enter the details and search
The destination is specified.
Fax Operations (Option) Searching for a registered destination (Index button) Destinations can be searched for using the specified search word when a destination is registered.
The index default display can be changed with the Address Book Index Default Setting.
% Touch Index buttons ([Favorites], [ABC] - [WXYZ], [etc]) displayed in the [Address Book] tab.
Desired destination button is displayed. Searching for a registered destination (Address type) Destinations can be searched by the address type (Fax, E-mail etc.).
Touch [Search] in the [Address Book] tab.

Touch [Address Type].

Select the address type.
The default display settings of the [Address Book] tab can be changed to address type with the Default Address Book setting.
Desired destination button is displayed. Searching for registered destinations (Detail search) Destinations can be searched using part of the destination name or fax number.

Touch [Detail Search].

When a destination applicable to the entered information is not found, "Search Result: 0" is displayed and no button is on the screen.
Touch [Name] or [Address]. Enter the name or fax number using the keyboard displayed on the screen and touch [OK].
Desired destination button is displayed. Specifying by direct input A destination can be specified by direct input even if the destination is not registered with the address book.
When [Manual Destination Input] is forbidden, the [Direct Input] tab is not displayed.
% Enter the fax number of the recipient. Enter the fax number of the recipient using the keypad or screen keyboard. Entered numbers are all cleared by pressing [C] (clear) key.
Special dialing symbols such as tone, pause, -, etc. are entered if necessary. [Tone]: If pulse dialing is being used, touch this button to send a push-button tone. Tone is used when a fax data services, etc are used. "T" appears on the screen. [Pause]: Touch this button to insert a pause when dialing. Touch [Pause] once to insert a 1-second pause; multiple pauses can be entered. "P" appears on the screen. [-]: Entered as a delimiter when dialing. This has no effect on dailing. "-" appears on the screen. When the keypad is used, the fax number can be entered directly even when [Address Book] tab or the [Job History] tab is displayed. When using a dial (pulse) line, it is possible to change to push tone by just touching [*]. The destination is specified.

MULTIFUNCTION COLOUR DIGITAL SYSTEMS
COLOUR MULTIFUNCTION SPEED MODULAR NETWORK
A COMPLETE ARRAY OF PROFESSIONAL COLOUR SHADES
Advanced multi-function systems deliver speed and networking for large departmental organisations

MAIN CHARACTERISTICS

1024 MB MEMORY AND 60 GB HDD LARGE 8.5" COLOUR CONTROL PANEL
DUPLEX FOR PAPER FORMATS UP TO 256 g/m2
STANDARD PAPER CAPACITY 3650 CUT SHEETS

STANDARD POSTSCRIPT 3

ADVANCED SECURITY OPTIONS
FAST AND FLEXIBLE SCANNING AT UP TO 70 opm
PROFESSIONAL FINISHING OPTIONS
EFFICIENCY AND PRODUCTIVITY The Olivetti d-Color MF450 and d-Color MF550 are innovative multi-function systems with a 60 GB Hard Disk to simplify information access and transmission. Based on single-pass tandem technology, they operate at impressive speeds of 45 ppm and 55 ppm respectively, for b/w and colour jobs with the A4 format. Their 1024 MB memory ensures efficient management of complex documents and print queues. COMPATIBILITY The Olivetti d-Color MF450 and d-Color MF550 feature an innovative print controller for complete integration with the corporate network and support for the Windows, MAC, Unix and Citrix operating systems. Both devices have a single user interface encompassing PCL and PostScript,
for fast and easy execution of all print processes run by the user software. SECURITY The distinguishing feature of these two models is the revolutionary biometric authentication option, a system that enhances security and protection by identifying each users individual physical characteristics. This eliminates the possibility of false authentications and avoids the need for users to remember ID codes. Additional security features include a PDF encryption function to prevent unauthorised access to PDF data, and a secure printing function that allows jobs sent to the system to be printed only when the user keys in a personal password.
POLYMERISED TONER for excellent colour printouts
ADVANCED SECURITY FUNCTIONS via fingerprints
Toouch-screen colour CONTROL PANEL
COLOUR The polymer toner ensures outstanding fidelity, brightness and definition, for superior colour images; chromatic stability is tested and guaranteed on cycles of up to 1,000 continuous copies. The toner provides excellent performance and reliability to ensure superior quantitative yields, and helps save energy by operating at lower temperatures. DESIGN The d-Color MF450 and MF550 combine style and elegance with functionality and leading-edge technology. Based on an all-round design concept, these Olivetti multi-function devices act as hub for all of the companys printing needs. Thanks to their compact design and broad colour display, which can be tilted and swivelled, they add a touch of class to any environment, creating a stylish focus of attention in the office.
SMALL-SCALE PUBLISHING The Olivetti d-Color MF450 and MF550 guarantee efficient, cost-effective production of a wide range of documents, including business cards, posters, brochures, leaflets. Superior printing quality and a broad choice of professional finishing options allow users to handle the entire production process in-house, for printed material of the highest standard.

Corner stapling

2-point stapling

Duplex

Combined mixplex/mixmedia

Sheet insertion, report

Letter fold

Booklet

Offset sorting
HIGH-DEFINITION IMAGES AND TEXTS: THE PERFECT SOLUTION FOR IN-HOUSE PUBLISHING
A MODULAR SYSTEM THAT GROWS AS USER NEEDS CHANGE

OPTIONS

Finishing units (only for MF450) Finishing units (only for MF550)

SD-505 Saddle Kit MF450

DF-611 Document feeder
PI-503 Post Inserter MF550

PK-512 Punch kit MF550

MT-502 Mailbin Unit MF450
OT-602 Additional Bin MF450
FS-519 Embedded Finisher MF450 MF450 ZU-603 Z-Fold MF550 FS-518 Staple finisher MF550

PK-510 Punch Kit MF450

Common options
OT-503 Output Tray MF450-MF550
PI-503 Post Inserter MF450-MF550
VI-504 Kit interface MF450-MF550

JS-504 Job separetor MF450-MF550
FS-608 Booklet finisher MF450-MF550
ZU-603 PK-512 Z-Fold Punch kit MF450-MF550 MF450-MF550
FS-517 Staple finisher MF450-MF550
LU-301 Large capacity Tray MF450-MF550
IC-409 Fiery Controller MF450-MF550

in alternative

A POWERFUL NETWORK COMMUNICATION TOOL
The scanner is a vital tool for circulating information on the company network. The integrated duplex unit simplifies scanning jobs for easier document networking. In addition to the usual functions of scan-to-email, scan-to-FTP, in the JPEG and TIFF formats, the d-Color MF450 and d-Color MF550 offer a multi-page capability to automatically convert heavier documents into ultra-compressed PDF files, for faster, streamlined transmission. Both devices enhance standard fax transmission procedures with a series of digital functions for more flexible fax management and lower telephone costs: colour fax transmission and storage with IP fax, transmission and reception of mail attachments via Internet Fax and re-routing of fax sent to PCs. With the Box function, all documents managed by the system can be memorised, archived and shared, for efficient data flows. The Box function can be used to display previews on the control panel of documents stored on the 60 GB hard disk, minimising the possibility of mistakes and wasted paper.

NETWORK SHARING

b/w Scan to SMB

colour

Copying

Scan to FTP

Scanning Printing

PCL-PS

Local/network

Scan to e-mail

IP-Fax

Faxing

Scan to box/ personal box

PC-Fax

SIP-Fax

Super G3 Fax

GENERAL SPECIFICATIONS
Type desktop/console Technology CPU Controller System Memory HDD Interfaces GENERAL First Copy Time Full-Colour console Tandem type Indirect electrophotographic Power PCMC7448@867MHz 1.024MB 60 GB (Standard) 10-Base-T/100-Base-T/1000-Base-T Ethernet, USB 2.0 Colour: 6,5 seconds (A4) MF450: 4,8 seconds in B/W (A4) MF550: 4,3 seconds in B/W (A4) MF450: 45 ppm B/W and 45 ppm in colour (A4) 23 ppm B/W and 23 ppm in colour (A3) MF550: 55 ppm B/W and 45 ppm in colour (A4) 28 ppm B/W and 23 ppm in colour (A3) Up to 100 sheets Up to 150 sheets (up to 300 g/m2) A6 - A3 Wide (311x457 mm), customised format 600 x 600 dpi Approximately 85 seconds 1-999 sheets 25-400% (0,1 % step)

1,800 x 600 dpi

Paper weight Greyscale Warm-up time Power requirements Power consumption Paper Capacity Automatic Duplexing Dimensions (WxDxH) Weight Finishing (option)
64-300 g/mlevels Approx. 30 seconds 220-240V 10A 50/60Hz Less than 2000 W (system) Std: 3,650 sheets Max.: 6,650 sheets A5 - A3 Wide; 64 - 256 g/mx 777 x 1,150 mm Approx. 190 kg Offset, collate, stapler, hole punch, centre fold, letter fold, booklet Toner: up to 45,000 pages BLACK, up to 27,000 pages CMY Imaging unit: up to 300,000 pages BLACK, up to 100,000 pages CMY
System speed Paper input capacity By-pass Paper size Resolution COPIER Warm-up Time Multiple Copy Zoom Risoluzione di stampa PRINTER Languages Print functions

Lifletime consumables

Copy features
Chapter and cover mode, proof copy, adjustmnet test print, glossy mode, colour adjustment digital art, job recall, job setting memory, poster mode, overlay, stamping
PCL 6c (PCL 5c + XL3.0), PostScript 3 Operating Systems PCL, PS, TIFF, and PDF direct print, mixmedia and mixplex, protection copy Colour scanner Up to 70 opm in colour and B/W 600 x 600 dpi JPEG, TIFF, PDF, Compact PDF, encrypted PDF Super G3 Analogue, I-Fax, IP-Fax, SIP-Fax Max 600 x 600 dpi (ultrafine) MH, MR, MMH, JBIG
Windows 2000/XP/XP64/Vista 32/64 (under development); Machintosh 9.x/10.x, Server 2000/2003/2003 x64, Unix, Linux, Citrix Scan to FTP, Scan to SMB, Scan to e-mail, Scan to Box, TWAIN 2,100 (single + group) LDPA support Annotation (text/time/date) for PDF Up to 400 job programmes Up to 33,6 Kbps 128 MB 2,100 (single + group) Polling, delayed transmission, PC-fax, receipt to confidential box, receipt to mail, FTP, SMB
Type SCANNER Speed Resolution File format FAX (optional) Compatibility Protocols Resolution Compression methods
Scan modes Destinations Functions Transmission speed Back-up memory Destinations Functions
Product performances are referred to an appropriate use under optimal conditions. With the right to change technical specifications. The registered trademarks are the property of their respective owners. d-Color MF450 and MF550 are distributed by Olivetti S.p.A. (07/07) - Code: 26193-01
OLIVETTI S.P.A. VIA JERVIS IVREA (TO) ITALY www.olivetti.com