Monitor indications Memory gauge & battery check

Memory gauge

The memory gauge lights when you take a picture. When the gauge is lit, the camera is storing a picture on the SmartMedia card. The memory gauge indication changes as shown below depending on the shooting status. When the memory gauge is full, wait until the light goes out before you take any more shots. When taking still pictures
Shoot. Wait. Before shooting (Gauge is off) One picture taken (Lit) Shoot. Wait. More than two taken (Lit) Shoot. Wait. No more pictures can be taken (Fully Lit)

When recording movies

If you continue shooting Shoot. Wait. Before shooting (Gauge is off) During shooting (Gauge lit). Shooting is not possible until the light goes out completely. Movie recording finishes automatically when the memory gauge is fully lit.

Battery check

If the remaining battery power is low, the battery check indication changes as follows when the camera is turned on or while the camera is in use.
No indication (The green lamp and orange lamp next to the viewfinder blink.) Remaining power level: exhausted. BATTERY EMPTY is displayed. Replace with new batteries.
Lights. (green) Remaining power level: high
Lights. (red) Remaining power level: low. Replace with new batteries.

How to use this manual

The instructions in this manual use a series of numbers for each operating procedure and button/dial illustration. Follow these numbers in order when operating the camera. If a button is shown in black, press it as part of the step.
Shooting mode setting Mode dial (Cont.)
Shutter speed setting Shutter priority shooting

Mode dial setting

1 Select S from A/S/M/ setting. See P. 48. 2
To set a faster shutter speed, press.

buttons

Show the modes that the function can be used with. You can set the mode dial to any of the positions shown.
To set a slower shutter speed, press.

Information display

Lets you select the amount of shooting information displayed in the shooting or playback mode. When it is set to OFF, only a small amount of information is displayed. For details on each piece of information displayed, see pages 12 to 15.

button

P A/S/M/ : In the top menu, select MODE MENU T SETUP T INFO T ON. Press. Press again to cancel the menu. : Press to display the top menu. Pressing turns INFO on. ~ How to use the menu (P. 39)
How to use the menu is shown here. Set the functions in the menus in the order of these arrows. Before using the menus, read Using the menus, Chapter 3 for details.
, , and used in instructions correspond to the buttons on the arrow pad as shown.

This sample page is only for your reference. It may differ from the actual page in this manual.

Attaching the strap

string to the lens cap: 1 Attach theloop through the hole inPull the string the lens cap. Put the other end of the string through the string loop. Pull 2 Loosen the strap in both stoppers.each out the ends of the strap from

Ring Stopper

stopper, then pull them out of each ring. of the strap A through 3 Thread one end(attached to the lens cap the string loop in step 1). Then, thread it through the cameras strap eyelet. the strap back 4 Thread the end ofand stopper as through the ring indicated by the arrows.

Strap eyelet

length that you like, 5 When you have a in the stopper B to pull on the strap make sure it is securely fastened. strap 6 Attach thesteps 3to the other strap eyelet following 5.
Be careful with the strap when you carry the camera, as the strap can easily catch on stray objects, causing serious damage. Attach the strap correctly as shown so that the camera does not fall off. If the strap is attached incorrectly and the camera falls off the strap, Olympus is not responsible for any damages.

Loading the batteries

This camera uses 2 CR-V3 lithium battery packs or 4 AA (R6) NiMH batteries, NiCd batteries, alkaline batteries or lithium batteries. Important: CR-V3 lithium battery packs cannot be re-charged. Do not peel the label on a CR-V3 lithium battery pack. the camera is turned 1 Make suredial is set to OFF). off (i.e. the mode

Mode dial

on 2 Slide the battery compartment lock the the battery compartment cover in direction of.
the battery cover in 3 Slidedirection ofcompartmentA ) with the the arrow ( your fingertip and open it (B). Do not use your fingernail, as this could result in injury.
the batteries in 4 Insert in the illustration. the direction shown

Battery alignment

When using CR-V3 lithium battery packs
When using AA (R6) batteries
Loading the batteries (Cont.)
the 5 Closepressbattery compartment cover, then it down (C) and slide it in the opposite direction of the arrow printed on it (D). When pressing the battery compartment cover shut, be sure to press the center of the cover, as it may be difficult to close properly by pressing the edge. Make sure the cover is completely closed. on 6 Slide the battery compartment lock the the battery compartment cover in direction of.

To avoid camera movement, we recommend use of a tripod for any effect which uses a slow shutter speed.
When the bar is displayed

Using My Mode

When using My Mode, the shooting mode you selected with the menus in the mode is activated. You can also save the shooting mode or function settings you are currently using in the mode. If you set the mode dial to again, the camera will activate these stored settings. In MY MODE SETUP, you can create and save up to 4 different My Mode settings. ~ MY MODE SETUP (P. 151)
Follow steps 1 through 3 in A/S/M/ select 1 , 2 , 3 or 4.
mode setting (P. 48). In step 3
Although the settings you are using can be saved, the zoom position you are currently using will not be saved.
How to use the shutter button 1 Point the camera towards the subject. Place the AF target mark on the
subject while viewing through the viewfinder. Press the shutter button gently (halfway). When the focus and brightness (exposure) are locked, the green lamp next to the viewfinder lights steadily.
Viewfinder AF target mark Green lamp Card access lamp Shutter button
2 Press the shutter button all the way. Shooting starts and the green lamp blinks.
P, A/S/M/ , , , , , or mode: The camera starts storing your pictures on the card. While pictures are being stored, the card access lamp blinks. mode: The camera starts recording a movie and the orange lamp lights.
the (movie record) mode: 3 ONLY forrecording, press the shutter To stop button all the way again. The card access lamp blinks and the camera starts storing the movie on the card. You cannot record another movie until the card access lamp stops blinking,

Focusing

Chapter 4 Auto focus
When you place the AF target mark on a subject and press the shutter button halfway, the green lamp lights up. This means that focusing is being performed automatically. If the green lamp blinks, focusing is not correct. If this happens, use Manual focus (P. 63) or Focus lock (P. 59).
Viewfinder AF target mark Green lamp Shutter button

Spot metering Selecting the metering area
Exposure is determined by metering within the AF target mark. In this mode, a subject can be shot with optimal exposure regardless of the background light. In the working range of the macro mode, spot metering is also available (spot metering+macro mode).

1 Press the (spot

button repeatedly until metering) or (spot metering+macro mode) appears. The monitor turns on automatically. The indications change as follows (if all modes are available):
When selecting OFF (Digital ESP) button

~ Macro mode (P. 89)

Spot metering

Take a picture.

Factory default setting: Digital ESP
Metering modes Metering the subject brightness (Cont.)
Meters the brightness of the subject at up to 8 different points to set the optimal exposure based on the average brightness. Useful with high-contrast subjects. In the M or mode, multi-metering is not available.

button Shutter button

Setting multi-metering
1 Set AE lock to the ~ Setting the

(P. 146).

button. custom button
engage 2 Press mode to 82). metering (P.

the spot

menu, select MODE MENU T 3 In the top T MULTI METERING T ON. CAMERA Press. Press again to cancel the menu. ~ How to use the menu (P. 39)
Multi-metering Metering the exposure of more than one point in the frame
Using multi-metering the AF 1 Pointto meter target mark where you want the exposure. Press the button. The subjects brightness can be metered at up to 8 different points. A metering bar appears on the monitor. Brightness meter readings are ignored after the 9th reading. To cancel the locked multi-metering exposure, hold down over 1 second to display MEMO. Press it again and release it quickly.

2 Take a picture.

e.g. : When metering 2 points (pressing twice). The average values for the aperture and shutter speed as calculated by metering 2 points. These values are recalculated every time another metering point is added. indicates the average for the 2 metering points. The average is always shown at the center of the bar.
indicates how much the present exposure you are metering is different from the average exposure value. The present exposure can be fixed by pressing the shutter button halfway down. (The present exposure is not added to the average value unless you press.)
The reading with pressed. indicates the number of times you have pressed the button indicates the difference between the metered and average readings.
When moves 3 far from the center of the bar (the average reading), the red appears.
: Available, : Not available
If multi-metering is not engaged T In the Digital ESP mode, multi-metering is not available. Set the metering mode to spot metering or spot metering + macro mode. How to save the locked multi-metering exposure after shooting (AE memory) T After pressing as many times as required in step 1 of Using multi-metering, hold it down for more than 1 second. MEMO appears. When MEMO appears, the locked exposure is memorized.

Press to select the exposure 2 differential between each frame (0.3, 0.7, 1.0), then press.

0.3 0.7 1.0

CANCEL SELECT
Auto bracketing Shooting pictures sequentially with a different exposure for each frame BKT
3 Press to select the number of frames to shoot (x3, x5), then press.
In some combinations of picture size and record mode, only x3 is available.
4 Take pictures. button all the way and Press the shutter
keep it pressed to shoot the preset number of pictures. You can stop shooting at any time by releasing the shutter button. Modes & Drive mode

Drive mode BKT

: Available, : Not available A, S, M or S-Prg column.
* The available settings differ depending on which shooting mode is selected. See the P,
In the following situations, sequential shooting ( , , BKT) is not possible: When the record mode is set to TIFF (P. 102) or when the SHQ record mode is set to ENLARGE SIZE (P. 106). When NOISE REDUCTION is set to ON (P. 116). During sequential shooting ( , , BKT), the main flash does not fire. If there is not enough space available on the card for the number of frames you have set during auto bracketing, you cannot continue shooting. If self-timer shooting is attempted when the still picture shooting mode (P, A/S/M/ , , , , , , ) is set to sequential shooting, the camera shoots 5 frames automatically. If the ISO is set to over 200, noise may appear under some shooting conditions (P. 107). If the battery power is low and the battery check blinks during sequential shooting, shooting stops and the camera starts saving the pictures you have taken. Whether or not all of the shots are saved depends on how much battery power remains. Since the shutter speed is set to 1/30 sec. max., exposure is decreased when shooting a dark subject to prevent camera movement. To use the external flash during sequential shooting, set the external flash so that it fires for each frame.

Panorama shooting

You can take advantage of panorama shooting with both Olympus CAMEDIAbrand cards and CAMEDIA Master software. (Non-Olympus cards do not support this feature.) Panorama shooting lets you connect images with overlapping edges into a single panoramic image, using the provided CAMEDIA Master software.

Picture rotation

There may be times when you want to rotate a picture. For example, pictures taken with the camera held vertically are also oriented vertically (i.e. longer vertically than horizontally). With picture rotation, you can turn them horizontally, 90 degrees clockwise, or counter-clockwise.
(Picture rotation) button Normal playback of a vertically oriented picture
vertically 1 Display apicture in oriented the single-frame playback mode (P. 117).

02.12.23 21:56

2 Each time the (picture rotation)
button is pressed, the picture is rotated as shown.
HQ Picture rotated 90 counterclockwise from normal playback position 24
Picture rotated 90 clockwise from normal playback position
Movie pictures cannot be rotated. New picture orientations are saved even when the power is turned off. Close-up playback is possible after pictures are rotated. However, pictures cannot be rotated while in close-up playback (P. 129). The following pictures cannot be rotated: protected pictures, pictures on a card with a write-protect seal, pictures taken with other cameras.
All reset Saving the cameras settings
Chapter 8 Useful functions
This function lets you choose whether or not the camera saves its current settings. OFF: The settings made just before the power is turned off are saved. ON : All settings are returned to the factory default settings (P. 144). The settings affected by All Reset are listed below. The ALL RESET setting (ON/OFF) applies to all the modes. If ALL RESET is set to OFF in one shooting mode, this setting applies to all other shooting modes, as well as the playback and modes. When ALL RESET is set to OFF, the OFF setting does not apply to functions (For example, : setting FULLTIME AF, INFO, etc.) that are not available in the current mode. All reset does not affect the menus SETUP items.
In the top menu, select MODE MENU T SETUP T ALL RESET T ON or OFF. Press. Press again to cancel the menu. ~ How to use the menu (P. 39) Factory default setting: ON
All reset Saving the cameras settings (Cont.)
Items that All Reset affects
Setting FNo (P. 53) SHUTTER (P. 54) (P. 108) LCD* ZOOM (P. 73) FLASH MODE (P. 75) (P.82, 89) (P. 91) DRIVE (P. 92) AF/MF (P. 63) ISO (P. 107) (P. 81) FLASH (P. 177) SLOW (P. 78) NOISE REDUCTION (P. 116) MULTI METERING (P. 83) AF AUTO 0 IN+ SLOW1 OFF OFF Factory default setting F2.8 1/OFF 32mm AUTO OFF OFF Setting DIGITAL ZOOM (P. 74) FULLTIME AF (P. 61) AF MODE (P. 60) (P. 90) PANORAMA (P. 96) 2 IN 1 (P. 98) FUNCTION (P. 100) INFO (P. 155) (P. 157) (for still pictures) (P. 102) WB (P. 109) (P. 112) SHARPNESS (P. 113) CONTRAST (P. 114) SATURATION (P. 115) Factory default setting OFF OFF iESP OFF OFF OFF OFF OFF OFF HQ AUTO 0 0

1MY MODE SETUP

SET CURRENT SETTING

1 MY MODE SETUP

SET CANCEL

ALL RESET CANCEL

MODE SETUP 5 Set CUSTOM on the MYto select the screen. Press functions you want, then press.
6 Select the setting within the. function by using , then press
Repeat Steps 5 and 6 to change other functions. Ex: When setting the aperture on the MY MODE SETUP screen.
Increases the value. Decreases the value.
Press to go to the aperture setting screen.
MY MODE SETUP P/A/S/M/S-Prg P/A/S/M/S-Pr P

FNo SHUTTER LCD

MY MODE SETUP P/A/S/M/S-Prg P/A/S/M/S-Pr

FNo SHUTTER

Press to save the setting. The monitor then returns to the previous screen.
have all 7 When youpress madeexit the settings you want, to from the MY MODE SETUP screen. Custom setting registration is complete. The menu displayed in step 2 appears.

8 Press

to exit from the menu.
When you save settings in CURRENT, the saved zoom position may differ from the zoom position you are using. The zoom position is set to one of the 4 zoom positions included in ZOOM (function included in MY MODE SETUP). The value closest to the current zoom position will be selected.
Available Items and Factory Default Settings
Setting P/A/S/M/S-Prg (P. 49 52) FNo (P. 53) SHUTTER (P. 54) (P. 108) LCD*1 ZOOM*2 (P. 73) FLASH MODE (P. 75) (P. 82, 89) (P. 91) DRIVE (P. 92) AF/MF (P. 63) ISO (P. 107) (P. 81) FLASH (P. 177) SLOW (P. 78) NOISE REDUCTION (P. 116) MULTI METERING (P. 83) AF AUTO 0 IN+ SLOW1 OFF OFF Factory default setting P F2.8 1/OFF 32mm AUTO OFF OFF Setting DIGITAL ZOOM (P. 74) FULLTIME AF (P. 61) AF MODE (P. 60) (P. 90) PANORAMA (P. 96) 2 IN 1 (P. 98) FUNCTION (P. 100) INFO (P. 155) (P. 157) (for still pictures) (P. 102) WB (P. 109) (P. 112) SHARPNESS (P. 113) CONTRAST (P. 114) SATURATION (P. 115) Factory default setting OFF OFF iESP OFF OFF OFF OFF OFF OFF HQ AUTO 0 0
*1 This sets the monitors ON/OFF when the camera is turned on. *2 In the mode, available zoom positions are 32mm/50mm/70mm/96mm (these numbers are based on a 35 mm camera).
P A/S/M/ : In the top menu, select MODE MENU T SETUP T INFO T ON. Press. Press again to cancel the menu. : Press to display the top menu. Pressing turns INFO on. ~ How to use the menu (P. 39) All shooting information is displayed. To turn INFO off in the playback mode, press again to bring up the top menu and press. Example: Playback mode
HQ SIZE: 2288x1712 F2.8 1/800 +2.0 ISO100 02.09.12 12:30 FILE: 1000020

When INFO is ON

When INFO is OFF
In the mode, INFO is not available.
Monitor brightness adjustment
Adjusts the brightness of the monitor.
To brighten the press To 2 darken it, pressmonitor,complete.the. To setting, press.

When you want to print out pictures that you have taken with this camera and stored on a card, use one of the following options: Print Reserve (P. 169) for printing at a photo lab that supports DPOF or for printing on a DPOF compatible printer Apply Print Reserve to your pictures. This allows you to add printing data (number of prints, date printed on pictures, etc.) to the pictures you have stored. What is DPOF? DPOF is short for Digital Print Order Format. DPOF is a format used to record automatic print information from cameras. By specifying which images are to be printed, the images can be printed easily by DPOFcompatible printing service labs or a personal DPOF-compatible printer. Printing on an Olympus CAMEDIA P-400, P-330N(E) or P-200 digital printer: If you insert a card with Print Reserve data into the printer, printing is possible without using a computer. For more details, refer to the printers instructions. Transferring pictures to a computer and printing them from a printer connected to the computer: If your computer has software applications installed that support JPEG images (Internet browsers, Paint software, etc.), you can print out your pictures on a printer connected to the computer. CAMEDIA Master software also enables printing. Print Reserve is not available. Also refer to the application software's instructions.
How to print pictures (Cont.)
Picture size and printing The resolution of a computer/printer is generally based on the number of dots (pixels) per square inch. This is called dpi (dots per inch). The higher the dpi value, the higher the resolution, and the better the printed results. Keep in mind, however, that the dpi of the picture you want to print does not change to match the printer resolution. This means that when you print an image with a lower resolution than the printer, the size of the printed picture will be smaller. Although you can print magnified images, picture quality will decrease. If you want to be able to print large, high-quality pictures, set the picture size in the camera as high as possible (higher record mode) (P. 102).

Troubleshooting

POSSIBLE CAUSES CORRECTIVE ACTION REF. PAGE
The camera does not turn on or function buttons do not respond. 1 The batteries are exhausted. 2 The power is off. 1 Replace the batteries with new ones. 2 Set the mode dial to any position except OFF to turn on the power. 3 Reload the batteries correctly. 4 The batteries may be too cold. Warm them before use by allowing them to return to room temperature, or if outdoors, putting them in an inner jacket pocket. 5 The camera will not operate while it is connected to a personal computer. 6 Operate the camera (press the shutter button, turn the mode dial, etc.) 1 Replace the batteries with new ones. The monitor does not turn on. 1 The camera is in the sleep mode. 1 Operate the camera (press the shutter button, turn the mode dial, etc.) P. 25 P. 19 P. 25
3 The batteries are loaded incorrectly. 4 The batteries are temporarily unable to function.

P. 19

5 It is connected to a personal computer. 6 The camera is in the sleep mode.
The green lamp and orange lamp blink at the same time. 1 The batteries are exhausted. P. 19

Troubleshooting (Cont.)

POSSIBLE CAUSES

CORRECTIVE ACTION

REF. PAGE
No picture is taken when the shutter button is pressed. 1 The mode dial is set to. 2 The memory gauge is full. 3 The flash has not finished charging. 1 Set the mode dial to any position except. 2 Wait until there is room in the memory gauge. 3 Remove your finger from the shutter button and wait until the orange lamp stops blinking. Take your shot again. 4 The recorded movie image data is being written to the card. You can start shooting again when the card access lamp stops blinking. 5 See the error code chart. 6 Erase unwanted pictures or insert a new card. Before erasing, download important images to a PC. 7 Replace the batteries with new ones. 8 Replace the batteries with new ones. (Do not open the battery compartment cover when the card access lamp is blinking.) 9 Insert a new card in the camera. P. 47 P. 16 P. 78
4 The card access lamp blinks after shooting in the mode.
5 There is a problem with the card. 6 The card is full.

P. 189 P. 137

7 The batteries ran out of power. 8 The monitor indications disappear, or only the battery check lights up.

P.19 P. 19

9 A write-protect adhesive seal is placed on the card or there is no card in the camera.
The date recorded with the image data is wrong. 1 The date is not set. 1 Set the date. The clock adjustment is not factorypreset. 2 Set the date again. P. 27
2 The camera has been left for too long with the batteries removed and the date/time setting was canceled.
Your customized settings have been canceled. 1 You turned off the power without saving the settings. 1 Set ALL RESET to OFF. P. 143

.)

(not available in
: Available, : Not available * Some functions are not available in some modes (A/S/M/ ). The shooting mode ( , , , or ) selected in the mode also affects availability of some functions. For details, refer to the individual function page.
Mode Function Contrast setting Saturation setting Noise reduction Custom button setting Shortcut setting All reset Language selection Beep Rec view Information display Histogram display Power on/off display setting Monitor brightness adjustment File name setting Pixel mapping M/ft setting Video output setting

Available only in.

Specifications
Product type Recording system Still Digital camera (for shooting and displaying) Digital recording, JPEG (in accordance with Design rule for Camera File system (DCF)), TIFF (non-compression), Digital Print Order Format (DPOF) QuickTime Motion JPEG support 3V (3.3V) SmartMedia, 4 MB - 128 MB (all cards except 2 MB) 1 frame (TIFF: 2288x1712) Approx. 5 frames (SHQ: 2288x1712) Approx. 16 frames (HQ: 2288x1712) Approx. 20 frames (SQ1: 2048x1536) Approx. 76 frames (SQ2: 1024x768) 4,000,000 pixels 1/1.8" CCD solid-state image pickup 4,130,000 (gross) 3200 x 2400 pixels (ENLARGE SIZE: SHQ/HQ) 2288 x 1712 pixels (TIFF/SHQ/HQ) 2288 x 1520 pixels (TIFF/SHQ/HQ) 2048 x 1536 pixels (TIFF/SQ1) 1600 x 1200 pixels (TIFF/SQ1) 1280 x 960 pixels (TIFF/SQ1) 1024 x 768 pixels (TIFF/SQ2) 640 x 480 pixels (TIFF/SQ2) Olympus lens 6.5 mm to 19.5 mm, f2.8 , 8 elements in 6 groups (equivalent to 32 mm to 96 mm lens on 35 mm camera) Digital ESP metering, Spot metering system f2.8 to f11 Used with mechanical shutter 1 to 1/1000 sec. (M mode: 16 to 1/1000 sec.; S mode: 4 to 1/1000 sec.) 1/30 to 1/8000 sec. Optical real image viewfinder
Movie Memory No. of storable pictures (When a 16 MB card is used)
No. of effective pixels Image pickup device Recording image resolutions
Photometric system Aperture Shutter speed Still

Movie Viewfinder

Specifications (Cont.)
Monitor Battery charging time for flash Autofocus 1.8" TFT color LCD display Approx. 114,000 pixels Approx. 6 sec. (at normal temperature with new batteries) TTL system autofocus, Contrast detection system, Focusing range: 2 cm to (0.7 in to ) DC-IN jack, USB connector (mini-B), VIDEO OUT jack, 5-pin external flash socket Up to 2099

Outer connector

Automatic calendar system Operating environment Temperature Humidity Power supply
0C to 40C (32F to104F) (operation) 20C to 60C ( 4F to 140F) (storage) 30% to 90% (operation) 10% to 90% (storage) For batteries, use 2 CR-V3 lithium battery packs, or 4 AA (R6) NiMH batteries, NiCd batteries, Alkaline batteries or lithium batteries. AC adapter (optional) Manganese (zinc-carbon) batteries cannot be used. 110 mm x 76 mm x 77.5 mm (4.3" x 3.0" x 3.1") 290 g (0.6 lb) (without batteries/card)
Dimensions (W) X (H) X (D) Weight

If your OS is Windows 98/98 SE, proceed to Installing the USB p.9). driver for Windows 98 ( p.11 Users running Windows Me/2000/XP p.31 Users running other OS

Mac OS (Macintosh)

Select About This Computer from the Apple menu on the menu bar. A window appears with the name of the computers OS. Confirm that the OS is OS 9.0-9.1 or OS X.
Users running Mac OS 9/X Users running other OS

p.23 p.31

Using Windows 98/Me/2000/XP

Make sure that:

Your computer is turned on and Windows is running. If you are running any applications, quit them all. You are recommended to power the camera using the optional AC adapter. If the battery power runs out while the computer is accessing the card in the camera, the camera will turn off in the middle of the operation and this could destroy image files (data). If you are using batteries, make sure that there is sufficient remaining battery power.
Installing the USB driver for Windows 98 (When using Windows 98/98 SE).... 9 Connecting the camera to the computer.. 11 Confirming the computer recognizes the camera. 14 Confirming the USB driver is installed. 15 Downloading images to your computer.. 17 Disconnecting the camera from your computer. 20
Installing the USB driver for Windows 98 (When using Windows 98/98 SE)
If your OS is Windows 98/98 SE, you must install the USB driver. Follow the instructions below to install the USB driver in your computer. Once it is fully installed, you do not need to repeat the procedure again. If your OS is Windows Me/2000/XP, skip the procedure below as the USB driver will be automatically installed. Proceed to Connecting the camera to p.11). the computer (
Insert the provided software CD into your CD-ROM drive.
The Olympus Windows Installer should automatically launch. Click USB driver for Windows 98.
If the installer is not automatically launched, select Run. on the Start menu and then execute (drive letter):/ Information.exe.
The drive letter of the CD-ROM varies depending on the computer. To identify the drive letter, double-click My Computer on the desktop.
Click Continue. The installation of the USB driver will start.
Click OK to restart your computer and the installation is complete.
When the computer has restarted, installation is complete. If the Olympus Windows Installer screen appears, click Close and remove the CD-ROM from the CD-ROM drive.
Connecting the camera to the computer
Users running Windows 98/98SE need to install the USB drive before connecting the camera to your computer for the first time. ( p.9)

When the image file has been downloaded to the computer, you can view images by double-clicking the image files downloaded to your computer. The files will be opened in the default image viewer of the operating system. If you want to view the image a different size or process it, you will need to open the image with software that supports JPEG or TIFF images files, such as Paint Shop Pro, Photoshop or CAMEDIA Master software. The lamp on the right of the viewfinder or the card access lamp blinks while the image is being copied. Never open the card cover on the camera, load or remove the batteries, or connect or disconnect the AC adapter while the lamp is blinking as the image files may be destroyed.
Disconnecting the camera from your computer
If your OS is Windows Me/2000, proceed to Windows Me/2000/XP ( p.21).

Windows 98

Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking. Some camera models have either a lamp on the right of the viewfinder or a card access lamp, and the location varies depending on the model. Refer to your cameras reference manual.
Double-click the My Computer icon and right-click the Removable Disk to display the menu.

Click Eject on the menu.

Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking.
Remove the USB cable from the camera.
Remove the USB cable from your computer.
Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking. Some camera models have either a lamp on the right of the viewfinder or a card access lamp, and the location varies depending on the model. Refer to your camera's reference manual.
Click the Unplug or Eject Hardware icon on the task bar. The message saying that the drive has been stopped appears. Click on the message. The Unplug or Eject Hardware window appears.
When a message appears, click OK.
If the window returns the following message when you click Unplug or Eject Hardware, first make sure that no image data is being downloaded from the camera, and then remove the USB cable.

Using Mac OS (9/X)

Your computer is turned on and Mac OS is running. If you are running any applications, quit them all. You are recommended to power the camera using the optional AC adapter. If the battery power runs out while the computer is accessing the card in the camera, the camera will turn off in the middle of the operation and this could destroy image files (data). If you are using batteries, make sure that there is sufficient remaining battery power. If you are running Mac OS X, the connection to the computer and downloading the image data are verified. Restrictions such as the following may occur due to the OS. The image file properties are not displayed correctly. Images in the camera cannot be opened without first downloading them. etc. For more details, visit the Olympus web site.

Connecting the camera to the computer.. 24 Downloading images to your computer.. 26 Disconnecting the camera from your computer. 30
Insert the marked end of the USB cable into the USB port on your computer as shown below.
Turn the camera on. Camera with a lens barrier The power turns on automatically, with the exception of some models which require you to press the (monitor) button. When the camera is turned on, the green lamp on the right of the viewfinder lights up. Camera with a mode Set the mode dial to. (If the camera has a power switch as well as a mode dial, turn the power switch to ON.)
(monitor) button Mode dial
The computer recognizes the camera as a new device. The computer recognizes the camera automatically and an Untitled icon appears on the desktop. If you cannot find this icon, turn off the camera and connect again. Mac OS X When the computer has recognized the camera, the Apple Image p.29 Capture software automatically launches.

Mac OS 9

You can download images from the camera and save them in your computer (in this case, in the Hard Disk).
Double-click the Untitled icon displayed on the desktop when the camera is connected to the computer.
If you cannot find this icon, or if an error message appears when you doubleclick the icon, there may be a problem with one of the following: the cameras power source (the AC adapter is not properly connected or the battery power is low) the card (there is no card in the camera or there is a problem with the card) Check that you can play back pictures on the monitor of your camera. the USB cable (the camera is not properly connected to the computer by the USB cable). Apple File Exchange extension is not enabled. Please refer to your Apple operating system manual for instructions on how to enable this extension.
Double-click the 100OLYMP folder.
Image files (JPEG files) with files names such as P1010001.JPG are displayed.
Double-click the Macintosh HD icon on the desktop.
The Hard Disk window is displayed.
Drag & drop the image you want to save in the computer (in this case, P1010012.JPG) to the Hard Disk window. The image is saved in the computer (in the Hard disk). To select all images, click Edit > Select all.
When the image file has been copied to the computer, you can view images by double-clicking the image files in the Hard Disk folder. The files will be opened in the default image viewer of the operating system. If you want to view the image a different size or process it, you will need to open the image with software that supports JPEG or TIFF images files, such as Paint Shop Pro, Photoshop or CAMEDIA Master software. The lamp on the right of the viewfinder or the card access lamp blinks while the image is being copied. Never open the card cover on the camera, load or remove the batteries, or connect or disconnect the AC adapter while the lamp is blinking as the image files may be destroyed.

All data stored on the card is erased when the card is formatted.
Selecting a language for on-screen display
You can select a language for on-screen display. Available languages vary depending on the area where you purchased this camera. This reference manual shows the English on-screen display in the illustrations and explanations.
Set the mode dial to P and turn the camera on.
You can select the language in all modes.

Power switch Mode dial

Press e.
The top menu is displayed.
Press d on the arrow pad to select MODE MENU.

DRIVE MODE MENU WB

Top menu

SEtUP CARD PIC CAM

Press ac to select the SETUP tab, then press d.
ALL RESEt EV StEP PW ON SEtUP PW OFF SEtUP

ON 1/3EV ENGLISH

SETUP tab
Press ac to select W, then press d.
Press ac to select a language, then press e.
ENGLISH FRANCAIS DEUtSCH ESPAOL SELECt GO
Press e again to exit the menu.
To turn the camera off, set the power switch to OFF.
Setting the date and time
You can set the date and time in all modes.
The green frame moves to the selected item. Press c repeatedly to change the page until X is displayed.
Press ac to select X, then press d.

FILE NAME PIXEL MAPPING

'03.01.01 00.00 m
Press ac to select one of the following date formats: Y-M-D (Year/Month/Day), M-D-Y (Month/ Day/Year), D-M-Y (Day/Month/Year). Then press d.
Move to the year setting. The following steps show the procedure used when the date and time settings are set to Y-M-D.

SELECt

Press ac to set the year, then press d to move to the month setting.
To move back to the previous setting, press b. The first two digits of the year are fixed.
Repeat this procedure until the date and time are completely set.
The time is displayed in the 24-hour format. For example, 2pm will be displayed as 14:00.
For a more accurate setting, press e when the time signal hits 00 seconds.
10 To turn the camera off, set the

power switch to OFF.

The date and time settings will be canceled if the camera is left without the battery for approximately 5 days. The settings will be canceled more quickly if the battery was only loaded in the camera for a short time before being removed. Check that the correct date and time have been set before shooting.

Allows you to set the aperture manually. The camera sets the shutter speed automatically. By decreasing the aperture value (F-number), the camera will focus within a smaller range, producing a picture with a blurred background. Increasing the value forces the camera to focus over a wider range in the forward and backward directions, resulting in a picture in which both the subject and the background are in focus. gAperture priority shooting (P.86)
Aperture (F-number) is decreased. Aperture (F-number) is increased.
S Shutter priority shooting
Allows you to set the shutter speed manually. The camera sets the aperture automatically. Set the shutter speed according to the subject and the type of effect you want. gShutter priority shooting (P.87)
Setting the shutter speed higher lets you capture fastmoving action without blur. The subject will be clear and sharp, as if it is not moving.
Setting the shutter speed lower blurs a moving subject, giving the impression of movement.

M Manual shooting

Allows you to set the aperture and shutter speed manually. To check the exposure, refer to the exposure status display. This mode gives you more creative control, allowing you to make the settings you need to get the type of picture you want, regardless of optimum exposure. gManual shooting (P.88)

r My Mode

Allows you to save your favorite settings as your own personal mode and use these customized settings when taking pictures. Current settings can also be saved for retrieving by this mode. gMY MODE SETUP Setting a function in My Mode (P.170) gUsing My Mode (P.90)

n Movie record

This function allows you to record movies. The camera automatically determines the aperture and shutter speed. Sound is recorded at the same time. The focus and zoom are locked. If the distance to the subject changes, focus may be compromised. gRecording movies (P.70)

Situation-related modes

m Night Scene shooting
Suitable for shooting pictures in the evening or at night. The camera sets a slower shutter speed than is used in normal shooting. For example, if you take a picture of a street at night in P mode, the lack of brightness will result in a dark picture with only dots of light. In the Night Scene shooting mode, the true appearance of the street is captured. The camera automatically selects the optimal settings for this type of shooting condition. Since the shutter speed is slow, make sure you stabilize the camera by using a tripod.

(Auto-flash (No indication)
The flash fires automatically in low light or backlight conditions.
(Red-eye reduction flash (!)
The light from the flash may make the subjects eyes appear red in the picture. The red-eye reduction flash mode significantly reduces this phenomenon by emitting pre-flashes before firing the regular flash. This helps accustom the subjects eyes to the bright light and minimizes the redeye phenomenon.

Note Note

The subjects eyes appear red.
After the pre-flashes, it takes about 1 second before the shutter is released. Hold the camera firmly to avoid camera movement. Effectiveness may be limited if the subject is not looking directly at the pre-flashes, or if the shooting range is too far. Individual physical characteristics may also limit effectiveness.

(Fill-in flash (#)

The flash fires regardless of the available light. This mode is useful for eliminating shadows on the subjects face (such as shadows from tree leaves), in a backlight situation, or for correcting the color shift produced by artificial lighting (especially fluorescent light).
The fill-in flash may not have the desired effect under excessively bright light.

(Flash off ($)

The flash does not fire even in low light conditions. Use this mode in situations where flash photography is not desired or is prohibited. You can also use this mode when you want to shoot a natural-looking twilight or night scene. Since a slow shutter speed is automatically selected in low light situations when in the flash off mode, the use of a tripod is recommended to prevent your pictures from being blurred by camera movement.
(Slow synchronization (#SLOW1 #SLOW2 HSLOW1)
The slow synchronization flash is designed for slow shutter speeds. Normally, when shooting with a flash, shutter speeds cannot go below a certain level to prevent camera movement. But when shooting a night scene background, fast shutter speeds can make the background too dark. Slow synchronization flash allows both a slow shutter speed for the background and a flash for the subject. Since the shutter speed is slow, make sure you stabilize the camera by using a tripod. Otherwise, camera movement may cause the picture to be blurred. In S and M modes, the flash fires at the selected shutter speed.
1st curtain (front curtain) #SLOW1
Usually, regardless of the shutter speed, the flash fires right after the shutter fully opens. This is called 1st curtain. Unless you change it, this is how the flash always fires. The factory default setting for slow synchronization is #SLOW1.

2nd curtain (rear curtain) #SLOW2
The 2nd curtain fires just before the shutter closes. Changing the flash timing can create interesting effects in your picture, such as expressing the movement of a car by showing the tail-lights streaming backwards. The slower the shutter speed, the better the effects turn out. The slowest possible shutter speed depends on the shooting mode: M mode : 15 sec. (Bulb shot is also available.) P, A, S, m mode : 4 sec. When the shutter speed is set to 4 sec.

4 sec.

rear curtain
4 sec. 2nd curtain flash fires
0 1st curtain flash fires

front curtain

Shutter closes

Shutter fully opens

1st curtain with red-eye reduction H SLOW1
This mode is for when you want to use slow synchronization, yet also reduce the red-eye phenomenon. For instance, when shooting a person against a brightly lit night background. A normal flash might make the persons eyes red, but 1st curtain with red-eye reduction lets you capture the background correctly and reduce the red-eye phenomenon at the same time. 2nd curtain with red-eye reduction is not available.
Using the slow synchronization flash
Turn the control dial while holding down # and select #SLOW.

# Flash mode button

While holding down #, press e. Press ac to select #SLOW1, HSLOW or #SLOW2, then press e.
Press e again to exit the menu.
After the menu is displayed, release #.
TIPS Slow synchronization can also be set from the MODE MENU. In the top menu, select MODE MENU CAMERA #SLOW #SLOW1, HSLOW or #SLOW2, then press e. gHow to use the menus (P.49)
TIPS The flash intensity can be set in 1/3EV steps or 1/2EV steps. gExposure steps Selecting the adjustment increments (P.174)
The flash adjustment effect may not be sufficient if the shutter speed is faster than 1/300.
External flash (optional)

Using the external flash

Various types of flash shooting are possible with the Olympus FL series external flashes. The external flash can be used either by itself or together with the built-in flash. If the external flash is used, flash mode and exposure compensation will be detected automatically by the camera, allowing the built-in flash and external flash to function together. The external flash can be mounted on the camera by attaching it to the hot shoe on the top of the camera, or by using the exclusive FL-BK01 flash bracket (optional) and FL-CB02 bracket cable (optional). This chapter explains how to use the FL-20 when attached to the hot shoe.

SEt CARD PIC CAMERA DRIVE ISO MY MODE FLASH SLOW AF BKt HI

Auto bracketing

Under some conditions, you may obtain better results shooting with exposure compensation than by using the exposure setting considered optimal by the camera. When auto bracketing is set, the exposure is changed automatically for each frame while the shutter button is pressed. The exposure differential and number of frames can be selected in the menus. The focus and white balance are locked at the first frame. Ex : When BKT is set to 1.0 3
In the top menu, select MODE MENU CAMERA DRIVE BKT, and press d.
Select the exposure. Press ac to select 0.3, 0.7 or 1.0, then press d.
When the exposure adjustment is set to 1/2EV steps, select from 0.5, 1.0 and 1.5. gExposure steps Selecting the adjustment increments (P.174)

CANCEL

Select the number of pictures. Press ac to select x3 or x5, then press e.
In some combinations of picture size and record mode, only x3 is available. Press e repeatedly until the menu disappears.
Press the shutter button fully and keep it pressed to shoot the preset number of pictures. You can stop shooting at any time by releasing the shutter button.
Sequential shooting (i, j, k, 7) is not possible in the following situations: When the record mode is set to TIFF. When NOISE REDUCTION is set to ON. j and k are not available when the record mode is set to RAW. In sequential shooting mode (i, j, k, 7), the builtin flash does not fire. The external flash does not fire in 7 mode. Auto bracket shooting is not available in M mode. Since the shutter speed is set to 1/30 sec.max. except in S and M mode, exposure is decreased when shooting a dark subject to prevent camera movement. For auto bracketing in modes other than S mode, shooting is automatically set to 1/30 sec. if the shutter speed was other than 1/30 sec. for an exposure differential of 0. If the battery power is low and the battery check blinks during sequential shooting, shooting stops and the camera starts saving the pictures you have taken. Whether or not all of the shots are saved depends on how much battery power remains. In Auto bracket shooting, if available space on the card does not exceed the number of set pictures, the next picture may not be taken.

Panorama shooting

You can take advantage of panorama shooting with Olympus xD-Picture Card. Panorama shooting lets you connect pictures with overlapping edges into a single panoramic picture, using the CAMEDIA Master software.
In the top menu, select MODE MENU CAMERA PANORAMA and press d.

Press ac to select NEW FILE or OVERWRITE, then press e.
NEW FILE Stores the edited movie as a new movie. OVERWRITE Stores the edited movie with the same name as the original. The original movie is not stored.
EDIt NEW FILE OVERWRItE CANCEL SELECt GO
If you want to select different frames, select RESET and press e and repeat the procedure from Step 4. To quit the editing function, select CANCEL and press e.
EDIt OK RESEt CANCEL SELECt GO
The edited movie is stored and the screen returns to the playback mode.
You cannot edit movies with sound which were taken with another digital camera. You cannot select NEW FILE if there is insufficient memory space on the card.

Playback on a TV

Use the AV cable provided with the camera to play back recorded images on your TV. Both still pictures and movies can be played back.
Make sure that the TV and camera are turned off. Connect the A/V OUT jack on the camera to the video input terminal on the TV using the AV cable.
Connect to the TVs video input (yellow) and audio input (white) terminals.
AV cable A/V OUT jack (MONO)
Turn the TV on and set it to the video input mode.
For details of switching to video input, refer to your TVs instruction manual.
Set the mode dial to q and turn the camera on.
The last picture taken is displayed on the TV. Use the arrow pad to select the picture you want to display. The close-up playback, index display, slideshow and other playback functions can also be used on a TV screen. TIPS You are recommended to use the optional AC adapter when using the camera with a TV. Make sure that the cameras video output signal type is the same as the TVs video signal type. gVIDEO OUT Selecting the video signal type (P.194) The cameras monitor turns off automatically when the AV cable is connected to the camera. Be sure to use the AV cable provided to connect the camera to the TV. The picture may appear off-center on the TV screen. When pictures are compressed in order to fit the entire picture on the TV screen, a black frame appears around the picture. If the picture is output to a video printer via the TV, the black frame may be printed.

z Custom button

Functions that can be set on the custom button DRIVE (factory default setting) ISO MY MODE* NOISE REDUCTION DIGITAL ZOOM FULLTIME AF R (still pictures)
Settings made by the control dial o, i, j, k, 7* AUTO, 80, 100, 200, 400 1, 2, 3, 4, 5, 6, 7, 8 OFF, ON OFF, ON OFF, ON OFF, ON OFF, BLACK & WHITE, SEPIA, WHITE BOARD, BLACK BOARD RAW, TIFF*, SHQ*, HQ*, SQ1*, SQ2* AUTO, PRESET 1*, PRESET 2*, CUSTOM*, V NORMAL, I, L, m -5 to 0 to +5 -5 to 0 to +5 -5 to 0 to +5
Ref. Page P.108 P.125 P.90 P.137 P.73 P.92 P.117 P.116 P.120 P.128 P.137 P.134 P.135 P.136
FUNCTION K WB SCENE MODES SHARPNESS CONTRAST SATURATION
* The sub-menu lets you select further options.
Setting the custom button
In the top menu, select MODE MENU SETUP CUSTOM BUTTON, and press d.
SEtUP CARD EDIt PLAY VIDEO OUt SHORtCUt CUStOM BUttON

DUAL CONtROL PANEL

ON OFF

AF ILLUMINAtOR

Press ac to select the function you want to set, then press e.
CUStOM BUttON DRIVE ISO MY MODE NOISE REDUCtION SELECt GO
If the mode dial is set to a mode other than r and z is pressed when MY MODE is set on the custom button, the customized settings are not activated. Set the mode dial to r and press z to display the MY MODE screen.

Using the custom button

Press z.
The function currently set to the custom button appears on the monitor.
z Custom button Control dial
Turn the control dial while holding down z to set.
The z button is used in the same way as the direct button. g Direct button operations (P.42) When an operation guide is displayed at the bottom of the screen, more specific settings can be made. Ex1: When DRIVE is set on the custom button

HI DRIVE AF

Ex2: When MY MODE is set

MY MODE

Ex3: When CONTRAST is set

Shortcut

You can set three shortcut menus (A, B, C) on the top menu in a still picture shooting mode (P/A/S/M/r/m/l/k/j/i). This is useful when you want to go quickly to frequently-used functions.

Day (01 - 31) Month: Jan. - Sep. = 1 - 9, Oct.= A, Nov.= B, Dec.= C There are two settings from which you can choose: RESET or AUTO. Choose the one that is best for you when transferring images to a PC. File name settings RESET The file number and folder number are reset every time a new card is inserted in the camera. The folder number returns to No. 100 and the file number returns to No. 0001. This method is useful when grouping files on separate cards. AUTO Even if a new card is inserted, the folder number and file number are retained from the previous card, so the same file number is not used on different cards. This helps you to manage multiple cards. This method is useful when you want to manage all your files with sequential numbers.
In the top menu, select MODE MENU SETUP FILE NAME RESET or AUTO, and press e.
PIXEL MAPPING Checking the image processing functions
When the File No. reaches 9999, the file number returns to 0001 and the folder number changes. When both the Folder and File No. reach their respective maximum number (999/9999), the number of storable pictures becomes 0 even if the card is not full. No more pictures can be taken. Replace the card with a new one.
The Pixel Mapping feature allows the camera to check and adjust the CCD and image processing functions. It is not necessary to operate this function frequently. Approximately once a year is recommended. Wait over a minute after the monitor is used or continuous shots are taken to allow for proper performance of the Pixel Mapping function.
In the top menu, select MODE MENU SETUP PIXEL MAPPING, and press d.
gHow to use the menus (P.49) START appears.
The BUSY bar is displayed during Pixel Mapping. When Pixel Mapping is finished, the screen returns to the mode menu.
If you accidentally turn the camera off during Pixel Mapping, start again from Step 1.
Measurement units m/ft (meters/feet)
The measurement unit can be selected from either meters or feet in the manual focus mode. m ft At long ranges, the camera measures in meters, and at short ranges in centimeters. At long ranges, the camera measures in feet, and at short ranges in inches.

Select the print reservation method
SINGLE PRINT Makes a single-frame print reservation for the selected picture according to standard settings. MORE Sets the number of prints of the selected picture in the print reservation data. You can also add the date or file name, and trim the picture.
(Set a SINGLE PRINT reservation Press a.
Press a when the picture with < is displayed to cancel the reservation.
Print resevation mark is displayed.
(Set MORE print reservations Press c. Press ac to select the item you want to set, then press d.
Print information setting screen is displayed.

SELECt CANCEL

Press ac to select the item, then press e. The available options vary depending on the type of printer. Items outside the capability of the printer are not available. <

FILE NAME SELECt SEt

1 WItHOUt WItHOUt WItHOUt GO

DATE (

FILE NAME ( P
Sets the number of prints.You can select up to 10 prints. If you select WITH, pictures are printed with the date and time. ) If you select WITH, pictures are printed with the file name. Crops part of a recorded picture so that only the enlarged section is printed. gTrim the picture (P.219)
DATE and FILE NAME are not available in MULTI PRINT mode.
When you have finished all the settings for MORE, press e.
The screen displayed in Step 5 appears. To print more than one picture in PRINT and/or MULTI PRINT mode, repeat Steps 5 and 6 and make single and/or multiple print reservations for all the pictures you want to print. is displayed in MULTI PRINT mode.
The settings you have made are displayed.
The PRINT screen is displayed.
PRINt MORE PRINt OK CANCEL

Print the pictures.

Press ac to select OK or CANCEL, then press e. OK CANCEL Printing starts. The settings are canceled and the monitor returns to the PRINT MODE SELECT screen.
When printing is finished, the monitor returns to the PRINT MODE SELECT screen. gExiting direct printing (P.221)

(To cancel printing

Pressing e during print data transfer displays the screen for selecting whether to continue or cancel printing. To cancel printing, press ac to select CANCEL, then press e.

PRINt CONtINUE CANCEL SELECt GO

ALL PRINT mode

In the PRINT MODE SELECT screen, press ac to select ALL PRINT, then press e.

PRINT MODE SELECT

The available paper size settings vary depending on the type of printer. When the PRINT PAPER screen is not displayed, SIZE and BORDERLESS are set to < STANDARD. Go to Step 4.
Use ac to select framed or unframed, then press e.
OFF ( ) The image is printed inside a blank frame. ON ( ) The image is printed filling the entire page. The print size settings screen is displayed.
Press ac to select the item you want to set, then press d.
Press ac to select the item, then press e. If PRINT INFO cannot be set with your printer, go to Step 6. The available options vary depending on the type of printer. Items outside the capability of the printer are not available. DATE ( ) )

FILE NAME (

If you select WITH, pictures are printed with the date and time. If you select WITH, pictures are printed with the file name.
PRINt OK CANCEL CANCEL SELECt GO
ALL INDEX mode/PRINT ORDER mode
In the PRINT MODE SELECT screen, press ac to select ALL INDEX or PRINT ORDER, then press e.
The available paper size settings vary StANDARD StANDARD depending on the type of printer. Depending on the selected print mode, SIZE and BODERLESS cannot be GO CANCEL SELECt selected. When the PRINT PAPER screen is not displayed, SIZE and BORDERLESS are set to < STANDARD. Go to Step 4.
OFF ( ) The image is printed inside a blank frame. ON ( ) The image is printed filling the entire page. The print screen is displayed.
In All INDEX mode, the printer automatically selects the number of pictures per sheet, etc. All INDEX printing is only available on printers with an index function. The PRINT ORDER function is only available on DPOF-compatible printers.

Trim the picture

To set the trim by MORE in PRINT or MULTI PRINT mode, follow the procedure below.
Use the arrow pad and zoom lever to select the trimming position and size.
Press acbd to select the trimming frame, and turn the zoom lever toward W or T to decide the trimming size. Use the control dial to select the height and width of the trimming frame. 3:2 trimming size can be selected when the size of the selected picture is 2592 1944, or 2592 1728. If trimming has already been set, the P screen appears. Press ac to select RESET, then press e.

Pictures you have taken do not appear on the monitor.

P.139 P.139, 140

Single-frame erase and all-frame erase cannot be performed.
No picture is displayed on the TV when connected to the camera.

P.194 P.152

Possible cause The brightness is not adjusted properly. The monitor is exposed to direct sunlight.
Corrective action Select s in the mode menu and adjust the brightness. Position the monitor in the down position or block the sunlight with your hand.

Ref. Page P.181

(When the camera is connected to a PC or Printer.
Possible cause The USB driver cannot be installed Corrective action It is necessary to install the USB driver for Windows 98/98SE. For how to install, see DIGITAL CAMERA-PC CONNECTION OPERATION MANUAL on the CD-ROM. Turn the power switch to ON and turn on the camera. Ref. Page
The camera is not recognized by the PC.
The power of the camera has not been turned on.

List of menus

P, A, S, M, r, m, l, k, j, i mode
Top menu MODE MENU Tab CAMERA Function DRIVE*1 ISO MY MODE*2 QFLASH #SLOW NOISE REDUCTION*3 DIGITAL ZOOM FULLTIME AF AF MODE ACCESSORY R (for still pictures) PANORAMA*IN 1 FUNCTION Setting o, i, j, k, 7 AUTO, 80, 100, 200, 400 MY MODE 1 to MY MODE 8 IN+Q, Q, SLAVE #SLOW1, HSLOW, #SLOW2 OFF, ON OFF, ON OFF, ON iESP, SPOT OFF, 1, OFF, ON

Ref. Page

P.108 P.125 P.90 P.81 P.79 P.137 P.73 P.92 P.91 P.119 P.117 P.111 P.113 P.116

u *9REAL*6 K WB

PICTURE
> CUSTOM WB SCENE MODES*3 SHARPNESS CONTRAST SATURATION CARD SETUP

CARD To the next page

OFF, BLACK & WHITE, SEPIA, WHITE BOARD, BLACK BOARD OFF, FON, ON, DIRECT OFF, ON, FRAME ASSIST OFF, ON RAW, TIFF, SHQ, HQ, SQ1, SQ2 AUTO, PRESET 1, PRESET 2, CUSTOM, V AUTO, PRESET1, PRESET2, V CUSTOM 1, CUSTOM 2, CUSTOM 3, CUSTOM 4 NORMAL, I, L, m -5 to +5 -5 to +5 -5 to +5 YES, NO
P.176 P.114 P.89 P.120 P.128
P.133 P.130 P.137 P.134 P.135 P.136 P.173

Click Continue. The installation of the USB driver will start.
Click OK to restart your computer and the installation is complete.
When the computer has restarted, installation is complete. If the Olympus Windows Installer screen appears, click Close and remove the CD-ROM from the CD-ROM drive.
Connecting the camera to the computer
Users running Windows 98/98SE need to install the USB drive before connecting the camera to your computer for the first time. ( p.9)
Some camera models have a USB setting in the menu. Make sure that PC is selected before connecting. This is not required if your camera [SETUP] tab Arrow pad does not have this setting. Menu button For details on how to operate the menu, refer to your camera's reference manual. Insert the marked end of the provided USB cable into the USB port on your computer as shown below.

Look for this mark.

Terminal
USB port The location of the USB port varies depending on the computer. For details, refer to your computer's manual.
After making sure that the camera is turned off, connect the end of the USB cable to the USB connector on the camera. The location of the USB connector or multi connector varies depending on the camera model. Refer to the camera manual for details.
Computer Rectangular terminal Smaller terminal USB port USB cable
USB connector or multi connector
Turn the camera on. Camera with a lens barrier The power turns on automatically, with the exception of some models which require you to press the (monitor) button. When the camera is turned on, the lamp on the right of the viewfinder lights up. Camera with a mode Set the mode dial to. (If the camera has a power switch as well as a mode dial, turn the power switch to ON.)

Lamp Lens barrier

(monitor) button Mode dial
Some camera models display this screen (shown right) on the monitor. When this screen appears, use the arrow pad to select PC and press the OK button.
The computer recognizes the camera as a new device. When you connect the camera to the computer for the first time, the computer automatically recognizes the camera. Click OK when the message saying that the installation is completed appears. The computer recognizes the camera as a Removable Disk.

If your OS is Windows Me/2000, proceed to Windows Me/2000/XP ( p.21).

Windows 98

Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking. Some camera models have either a lamp on the right of the viewfinder or a card access lamp, and the location varies depending on the model. Refer to your cameras reference manual.
Double-click the My Computer icon and right-click the Removable Disk to display the menu.

Click Eject on the menu.

Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking. The green lamp lights on some models. If the lamp is no flashing, then the cable can be removed.
Remove the USB cable from your computer.
Make sure that the lamp on the right of the viewfinder or the card access lamp is not blinking. Some camera models have either a lamp on the right of the viewfinder or a card access lamp, and the location varies depending on the model. Refer to your camera's reference manual.
Click the Unplug or Eject Hardware icon on the task bar. The message saying that the drive has been stopped appears. Click on the message. The Unplug or Eject Hardware window appears.
When a message appears, click OK.
If the window returns the following message when you click Unplug or Eject Hardware, first make sure that no image data is being downloaded from the camera, and then remove the USB cable.

Using Mac OS (9/X)

Your computer is turned on and Mac OS is running. If you are running any applications, quit them all. You are recommended to power the camera using the optional AC adapter. If the battery power runs out while the computer is accessing the card in the camera, the camera will turn off in the middle of the operation and this could destroy image files (data). If you are using batteries, make sure that there is sufficient remaining battery power. If you are running Mac OS X, the connection to the computer and downloading the image data are verified. Restrictions such as the following may occur due to the OS. The image file properties are not displayed correctly. Images in the camera cannot be opened without first downloading them. etc. For more details, visit the Olympus web site.
Connecting the camera to the computer.. 24 Downloading images to your computer.. 26 Disconnecting the camera from your computer. 30
Some camera models have a USB setting in the menu. Make sure that PC is selected before connecting. This is not required if your camera [SETUP] tab Arrow pad does not have this setting. Menu button For details on how to operate the menu, refer to your camera's reference manual. Insert the marked end of the USB cable into the USB port on your computer as shown below.