Cat. No. Z141-E1-02A

OMRON ELECTRONICS LLC

1 Commerce Drive Schaumburg, IL 60173 847.843.7900
For US technical support or other inquiries: 800.556.6766

F150-3 Vision Sensor

OMRON CANADA, INC.
885 Milner Avenue Toronto, Ontario M1B 5V8 416.286.6465
OMRON ON-LINE Global - http://www.omron.com USA - http://www.omron.com/oei Canada - http://www.omron.ca

Manual 1: SETUP MANUAL

ABC-E1-0 10/04/XXX Z141-E1-02A 09/04/100
2004 OMRON ELECTRONICS LLC Printed in the U.S.A.
Specifications subject to change without notice.

Setup Manual

Revised July 2003
Warranty, Limitations of Liability, Application Considerations Disclaimers Precautions in using the Product
Read and Understand this Manual
Please read and understand this manual before storing, installing, programming, operating, maintaining, or disposing of the products. Please consult your OMRON representative if you have any questions or comments.

WARRANTY

OMRONs exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING PARTICULAR NON-INFRINGEMENT, PURPOSE OF THE MERCHANTABILITY, PRODUCTS. ANY OR FITNESS OR FOR USER BUYER
ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRONS ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the product in the customers application or use of the products. At the customers request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this manual. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

CHANGE IN SPECIFICATIONS

Product specifications and accessoreies may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are mode. However, some specifications of the products may be changed without any notice. When in doubt, speciak model numbers may be assigned to fix or establish key specifications for your applications on your request. Please consult with your OMRON representative at any time to confirm actual spesifications of purchased products.

Notice:

OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property.

!Caution

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or property damage. High Temperatures Indicates particular circumstances which, if not avoided, could result in heat burns.

Visual Aids

The following headings will help you locate different types of information. Note Indicates information of particular interest for efficient and convenient operation of the product.
Indicates pages where additional information can be found. Indicates a procedure. The step numbers in the procedure correspond to the numbers in any related illustrations.

Trademark

DeviceNet is a registered trademark of the Open DeviceNet Vendor Association, Inc.

OMRON, 2000

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of OMRON. No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in this publication.

TABLE OF CONTENTS

PRECAUTIONS.

Safety Precautions. General Precautions.

xii xiii

SECTION 1 Before Installing.
1-1 1-2 1-3 Installation Precautions. Confirming Package Contents. Product Availability.
SECTION 2 Product Introduction.
2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 Overview of F150 Application. Component Names and Functions. Connections. Power Supply and Ground. Cameras with Light Sources. CCTV Lens. Lighting. Two-camera Unit. Mounting the Controller.
SECTION 3 Terminal Blocks.
3-1 3-2 3-3 Crimp Terminals and Cables. Specifications. Terminals.
SECTION 4 RS-232C Connection.
4-1 4-2 4-3 Connector. Wiring. Connection.
SECTION 5 CompoBus/D Connections.
5-1 5-2 Overview. Communications Specifications.
5-3 5-4 5-5 5-6 DIP Switch Settings. Connector Pin Allocation. LED Indicators. Multi-vendor Applications. 48 48
SECTION 6 Troubleshooting.
6-1 6-2 6-3 6-4 6-5 6-6 Connection Errors. Errors during Menu Operation. Terminal Block Errors. RS-232C Communications Errors. Two-camera Unit. LED Indicators (for F150-C10E-3-DRT).

SECTION 7 Maintenance.

7-1 7-2 Maintenance Parts and Replacement. Regular Inspections.
SECTION 8 Specifications.
8-1 8-2 8-3 8-4 8-5 8-6 8-7 F150 Vision Mate Controller. Cameras. Two-camera Unit. Console. Cables. Video Monitor. LCD Monitor.

Revision History.

About this Manual:
This manual describes the hardware for the F150 Vision Sensor and how to install the components, and it includes the sections described below. This is one of two manuals used to operate the F150.Refer to the following table for the contents of each manual. Manual 1: Setup Manual 2: Expert Menu Operation Manual Contents Provides information on system hardware and installation. Be sure to read this manual first. Cat. No. Z141-E1-1
Describes operation of the F150 using the Expert Z142-E1-1 Menu. The Expert Menu enables application of all F150 capabilities, including setting region images and criteria.
Please read the above manuals carefully and be sure you understand the information provided before attempting to install or operate the F150. Section 1 Before Installing describes the precautions that must be taken when installing and operating the F150 Vision Sensor. Section 2 Product Introduction provides an overview of F150 application and describes the wiring, Cameras, optical lenses, lighting modes, and light guides used in the F150 System. It also describes how to mount the Vision Mate Controller to DIN Track or to a flat surface. Section 3 Terminal Blocks describes how to connect the terminal blocks. Section 4 RS-232C Connection describes how to connect the RS-232C port. Section 5 CompoBus/D Connections describes how to connect the F150C10E-3-DRT Vision Sensor as a CompoBus/D Slave and provides information such as connector pin allocations, node number settings, and baud rate settings. Section 6 Troubleshooting lists the errors that may occur, along with their probable causes and remedies. Section 7 Maintenance provides information on maintenance and inspection. Section 8 Specifications provides the specifications of the F150 components.

!WARNING

Failure to read and understand the information provided in this manual may result in personal injury or death, damage to the product, or product failure. Please read each section in its entirety and be sure you understand the information provided in the section and related sections before attempting any of the procedures or operations given.

PRECAUTIONS

This section provides general precautions for using the F150 Vision Sensor. The information contained in this section is important for the safe and reliable application of the F150 Vision Sensor. You must read this section and understand the information contained before attempting to set up or operate a F150 Vision Sensor.

Safety Precautions

!Caution Do not touch fluorescent or halogen lights
while the power is ON or immediately after the power is turned OFF. These lights generate heat and can cause burns.
!Caution Do not use the F150 in environments with flammable or explosive gases.
!Caution Install the F150 away from high-voltage equipment or motors
to ensure safety during operation and maintenance.
!Caution Use crimp terminals for wiring. Do not connect bare stranded
wires directly to terminals.
!Caution Cover the terminal blocks with the Terminal Block Protection

Covers after wiring.

!Caution Use DC power supplies with safe extra low-voltage circuits
that prevent occurrences of high voltages in the main F150 power supply and power supplies for the terminal blocks.
!Caution Use the power supply cables and crimp terminals of specified

sizes.

!Caution Use at the power supply voltages specified in this manual. !Caution Be sure to securely tighten the screws when mounting F150

components.

!Caution Do not dismantle, repair or modify any F150 components. !Caution Dispose of F150 components as industrial waste.

General Precautions

The user must operate the product according to the performance specifications described in the setup manual. Before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems, machines, and equipment that may have a serious influence on lives and property if used improperly, consult your OMRON representative. Make sure that the ratings and performance characteristics of the product are sufficient for the systems, machines, and equipment, and be sure to provide the systems, machines, and equipment with double safety mechanisms.

SECTION 1 Before Installing
This section describes the precautions that must be taken when installing and operating the F150 Vision Sensor.
Installation Precautions.
1-1-1 F150 Components. 1-1-2 Installation Site. 1-1-3 Installation. 1-1-4 Cables. 1-1-5 Camera. 1-1-6 Video Monitor. 1-1-7 Prevention of Electrostatic Discharge. 1-1-8 Turning OFF the Power. 1-1-9 RESET Terminal. 1-1-10 Power ON Sequence for Two-camera Unit (F150-A20)

1-2 1-3

Confirming Package Contents. Product Availability.

Installation Precautions

Section 1-1
The F150 is highly reliable and resistant to most environmental factors. The following guidelines, however, must be followed to ensure reliability and optimum use of the F150.

F150 Components

Be sure to use the Camera, Camera Cable, and Console designed for the F150. 1. 2. 3. F150-S1A Camera F150-VS Camera Cable F150-KP Console

Installation Site

Do not install the F150 in locations subject to the following conditions: 1. Ambient temperatures outside of 0 to 40C for the F300M09 Video Monitor (recommended monitor) or outside of 0 to 50C for all other F150 components Condensation due to rapid temperature fluctuations Relative humidities outside 35% to 85% Corrosive or flammable gases Dust, salt, or iron particles Direct vibration or shock Direct sunlight Water, oil, or chemical fumes or spray

2. 3. 4. 5. 6. 7. 8.

Installation
Orientation of Controller To improve heat dissipation, install the Controller in the following orientation only:

CORRECT

Do not install the Controller in the orientations shown in the following diagram.

INCORRECT

Ambient Temperature 1. Maintain a minimum clearance of 50 mm above and below F150 components to improve air circulation. 2. Do not install F150 components immediately above strong heat sources, such as heaters, transformers, or large-capacity resistors. Do not let the ambient operating temperature exceed 50C. Provide a forced-air fan or air conditioning if the ambient temperature might exceed 50C.

Control box

Louver
Noise Resistance Use the following measures to help increase noise resistance. 1. Do not install F150 components in a cabinet containing high-voltage equipment.
Do not install the F150 components within 200 mm of power cables.

Power cable 200 mm min.

200 mm min.
F150-C10E-3-DRT (CompoBus/D Model) 1. Since the product is defined as built-in type, install the product inside the control panel. 2. Do not apply external forces exceeding 50 N to CompoBus/D connectors. When wiring communications cables, remove the connectors from the F150. Before setting the DIP switch or connecting cables, turn OFF the Programmable Controller, F150, and the communications power supply. Observe the following precautions when wiring communications cables. a) b) c) d) e) Separate communications cables from power lines or high-tension lines. Do not bend communications cables. Do not pull on communications cables with excessive force. Do not place heavy objects on communications cables. Be sure to route communications cables within ducts.

Cables

Always turn OFF the power before connecting or disconnecting cables.

Camera

The Cameras case is connected to the 0V line in the internal circuits. Heed the following precautions to prevent noise interference. 1. 2. Do not ground the Camera. Do not remove the base attached to the Camera.
Do not remove the core attached to the F150-VS Camera Cable.

Video Monitor

(When using the recommended F300-M09) Heed the following precautions to prevent noise interference if the video monitor case is metallic, because it is connected to the 0V line in the internal circuits. 1. 2. 3. Do not ground the video monitor. Do not ground the metallic part of the connector. Secure the video monitor with plastic screws if it is being mounted to a metallic surface.
Prevention of Electrostatic Discharge
To prevent damage from static electricity, use a wrist strap or another device for preventing electrostatic discharge when touching terminals or connector signal lines.

Turning OFF the Power

Do not turn OFF the power while a message is being displayed indicating that processing is being performed. Data in memory will be destroyed, and the F150 may not operate correctly the next time it is started.

RESET Terminal

Do not use RESET input immediately after power is turned ON. When using RESET input to synchronize execution timing, wait at least 1 s after turning ON the F150 power supply before turning ON the RESET terminal.

1-1-10

Power ON Sequence for Two-camera Unit (F150-A20)
If the F150 and the Two-camera Unit need to be started sequentially, turn ON the Two-camera Unit first and then turn ON the F150. If they are turned ON in the reverse order, image data may not be read correctly.
Confirming Package Contents

Section 1-2

Check the contents of the package as soon as you receive the F150. Contact the nearest OMRON representative if any of the following items are missing.

F150-C10E-3 F150-C15E-3 1. 2. 3. F150-C10E-3-DRT 1. 2. 3. 4. F150 Vision Mate Controller Setup Manual (this manual) Expert Menu Operation Manual F150 Vision Mate Controller Setup Manual (this manual) Expert Menu Operation Manual 1 1
CompoBus/D Connector (MSTB2.5/5-STF-5.08AU by Phoenix Contact) 1

Product Availability

Some of the products listed may not be available in some countries. Please contact your nearest OMRON sales office by referring to the addresses provided at the back of this manual.
SECTION 2 Product Introduction
This section provides an overview of F150 application and describes the wiring, Cameras, optical lenses, lighting modes, and light guides used in the F150. It also describes how to mount the Vision Mate Controller to DIN Track or to a flat surface.

2-1 2-2 2-3 2-4

Overview of F150 Application. Component Names and Functions. Connections. Power Supply and Ground.
2-4-1 Crimp Terminals and Cables. 2-4-2 Protective Conductor (Earth) Wiring. 2-4-3 Wiring the Power Supply.

2-5 2-6

Cameras with Light Sources. CCTV Lens.
2-6-1 Optical Chart. 2-6-2 Lens. 2-6-3 Extension Tubes.

2-7 2-8

Lighting.

2-7-1 Lighting Methods.

Two-camera Unit.
2-8-1 Connecting to the Power Supply. 2-8-2 Connecting to the F150. 2-8-3 Connecting to Cameras.

Mounting the Controller.

2-9-1 Mounting to DIN Track. 2-9-2 Mounting on a Flat Surface.
Overview of F150 Application

Section 2-1

The following table shows the basic steps that must be performed to use the F150.

Step Manual Setup Manual

Unit Connections and Wiring
Programmable Controller Power Supply
Console Synchronous sensor Camera with Light Source
IBM PC/AT or compatible computer
Setting Measurement Conditions
Expert Menu Operation Manual
3: Confirming Operation, Measuring Objects, and Outputting Results
IBM PC/AT or compatible computer Programmable Controller

Synchronous sensor

Component Names and Functions

Section 2-2

The following diagram shows the terminals, connectors, and indicators on the F150-C10E-3 and F150-C15E-3 Vision Mate Controller.

F150-C10E-3 F150-C15E-3

Ground Power supply Output terminal terminals terminals Input terminals
POWER indicator RUN indicator ERROR indicator Console connector Monitor connector

RS-232C connector

Camera connector

Output terminals

Do not open.
G A POWER Indicator Lit while power is ON. H B RUN Indicator Lit in RUN mode. C ERROR Indicator Lit when an error occurs. I D RS-232C Connector Connects the F150 to a computer, Programmable Controller, or other external device. J E Camera Connector Connects to the Camera. K F Power Supply Terminals Wired to the power supply.
Ground Terminal Wired to the ground. Input Terminals Wired to external devices, such as synchronous sensors or inputs from a Programmable Controller. Output Terminals Wired to external devices, such as synchronous sensors or outputs to a Programmable Controller. Monitor Connector Connects to the video monitor. Console Connector Connects to the Console.

F150-C10E3DRT

The F150-C10E-3-DRT can operate as a CompoBus/D Slave.
Ground terminal Power supply Output terminals terminals Input terminals
POWER indicator Monitor connector
RUN indicator ERROR indicator RS-232C connector

Console connector

MS indicator

NS indicator

Camera DIP connector switch
CompoBus/D connector Do not open.
A POWER Indicator Lit while power is ON. B RUN Indicator Lit in RUN mode. C ERROR Indicator Lit when an error occurs. D RS-232C Connector Connects the F150 to a computer, Programmable Controller, or other external device. E Camera Connector Connects to the Camera. F Power Supply Terminals Wired to the power supply. G Ground Terminal Wired to the ground. H Input Terminals Wired to external devices, such as synchronous sensors or inputs from a Programmable Controller.
I Output Terminals Wired to external devices, such as synchronous sensors or outputs to a Programmable Controller. J Monitor Connector Connects to the video monitor. K Console Connector Connects to the Console. L MS (Module Status) Indicator Indicates the status of the F150 in CompoBus/D communications. Lit in green when the F150 is operating normally. M NS (Network Status) Indicator Indicates the status of the network in CompoBus/D communications. Lit in green when the network is operating normally. N DIP Switch Used to set the node address and baud rate. O CompoBus/D Connector Connects the communications cable of the CompoBus/D network.

Connections

Section 2-3
Connect the basic components as shown in the following diagram. Details are provided later in this section.
!Caution Turn OFF the power to the Controller before connecting or

disconnecting cables. Connecting or disconnecting cables with power turned ON can damage peripheral devices. If the Two-camera Unit is connected, turn OFF the power to the Two-camera Unit as well as the power to the F150 itself before connecting or disconnecting cables.
Power Supply p. 14 (OMRON's S82K-01524 and S82K-05024 recommended.)
F150-KP Console (cable length: 2 m)
F150-VS Camera Cable (3m)
F150-VM Monitor Cable (2 m) BNC Jack (Monitor cable: Provided with the F150-VM.) Monitors F150-M05L Liquid Crystal Monitor F300-M09 Video Monitor
Cameras Camera with Intelligent Light Source (see note1.) p. 17 F150-SLC20 F150-SLC50 (20-mm field of vision) (50-mm field of vision)
Camera with Light Source (see note 2.) p. 16 F150-SL20A (20-mm field of vision) F150-S1A Camera F150-SL50A (See note 3.) p. 16 (50-mm field of vision)

1. 2. 3.

An F150-LTC20/LTC50 Intelligent Light Source (with dedicated lens) is attached to the F150-S1A Camera. An F150-LT10A Light Source (with dedicated lens) is attached to the F150-S1A Camera. If the field of vision is too small or too big, use the F150S1A Camera with a normal CCTV lens and light source. p. 20

Power Supply and Ground

Connecting to Two Cameras

To Cameras

Section 2-4

F150-A20 Two-camera Unit

Connection possible to different types of Camera.
Note Use a 24-VDC power supply.
F150-VS Camera Cable (3 m)

To F150 Camera Connector

F150-VA (15 cm) Camera Unit Cable (Provided with Two-camera Unit)
Wire the power supply and the ground to the top terminal block, and tighten the screws to a torque of between 0.5 and 0.6 Nm. After wiring, confirm that wiring and screw tightening have been performed properly.
!Caution Cover the terminal blocks with the Terminal Block Protection Covers.
Crimp Terminals and Cables
The terminal block uses M3 terminal screws. Use appropriate crimp terminals for M3 screws, as shown below.

Forked Round 6.2 mm max.

6.2 mm max.
Applicable wire size: Insulated wire of 1.31 to 1.65 mm2 (AWG16 to AWG15)

Protective Conductor (Earth) Wiring
Wire the ground as shown in the following diagram.
!Caution Use an appropriate ground. An insufficient ground can
affect F150 operation or result in damage to F150 components. To avoid damage to the equipment, do not share the protective conductor wiring with any other devices nor wire the protective conductor terminal to the girder. Be sure to wire the protective conductor of the equipment independently. Keep the ground line as short as possible.
Class I (with protective conductor terminal)

Wiring the Power Supply

Power Supplies Use a power supply with the following specifications. We recommend using OMRONs S82K-01524 Power Supply.
Item Output current Power supply voltage 0.6 A min. 24 VDC +10%/-15% Specification
When connecting the F150, Two-camera Unit, and F150M05L LCD Monitor to a single power supply, use a power supply that meets the following specifications. We recommend using OMRONs S82K-05024 Power Supply.
Item Output current Power supply voltage 1.6 A min. 24 VDC +10%/-15% Specification

24 VDC

Wire the Power Supply Unit independently of other devices. In particular, keep the power supply wired separately from inductive loads. Keep the power supply cable as short as possible (less than 10 m). If UL recognition is required, use a UL class II power supply.
Cameras with Light Sources

Section 2-5

A dedicated lens and light source have been attached to the F150 Camera (F150-S1A) to produce Cameras with Light Sources. The Light Source and Lens are a single unit and are thus compact and easy to mount.
Cameras with F150-LT10A Light Source The F150-S1A Cameras are shipped with a Lens and Light Source attached.
Field of vision 20 mm 50 mm F150-SL20A F150-SL50A Model
Cameras with Intelligent Light Source The F150-S1A Cameras are shipped with a Lens and Intelligent Light Source attached.
Field of vision 20 mm 50 mm F150-SLC20 F150-SLC50 Model

The Intelligent Light Source incorporates a DIP switch for specifying unit numbers. When using the Two-camera Unit, set the DIP switch on the Light Source connected to Camera 1 to 1.

F150-LTC20

Connected to Camera 0 Connected to Camera 1

F150-LTC50

Push up pin 1 on the DIP switch.
Shift pin 1 to the right.
Camera Only The same Camera is also available without a lens and light source so that standard CCTV lenses and lights can be used. Use C-mount lenses.
Camera Camera F150-S1A Model
!Caution The F150-S1A Camera must be used with the F150.
Using other Cameras can damage the F150 or the Camera.
Distance from Measurement Object
The Camera must be mounted at a distance from the measurement object where it can correctly view the object.
The Lens focus is fixed and the distance must be adjusted each time the Lens or Camera is changed because the field of vision and focus vary from Lens to Lens. The cameras set distance is an approximate value. The cameras mounting allows it to be adjusted slightly nearer to or farther from the object.

F150-SL20A/SL50A

Mounting dimensions p. 66

Measurement object

Camera distance 20-mm Lens: 61 to 71 mm 50-mm Lens: 66 to 76 mm
Field of Vision 20-mm Lens: mm 50-mm Lens: mm

F150-SLC20

Camera distance 15 to 25 mm

Field of Vision mm

F150-SLC50
Camera distance 16.5 to 26.5 mm
If the object size and field of vision are incompatible, attach a standard CCTV lens and light source to the Camera. p. 20

CCTV Lens

Section 2-6
When using a F150-S1A Camera (without a light source), refer to the following graph to select the appropriate Lens and Extension Tube. The lens will differ depending on the size of the measurement object and the distance from the Camera.

Optical Chart

The values in the following chart are approximations, and the Camera must be adjusted after it is mounted.

Lens model: 3Z4S-LE

Camera distance A (mm)

5,000 3,000 2,000

t: Extension Tube length

Field of vision L (mm)

A Visionary Partnership
Omron and CCS America have partnered to provide the CCS Intelligent Lighting Adapter (ILA), lighting power supplies and wide range of controllable LED lighting for Omrons F-series Vision Sensors.
Simplified Setup and Changeover
Take advantage of the time-saving, simple setup for lighting your vision application. Just plug the CCS Intelligent Lighting Adapter into the back of an Omron F-series camera and a CCS PD series digital power supply. Choose from over 200 CCS LED lighting options and connect it to the power supply. Set light intensity and angle using the F-series controllers software. Settings are saved in software and are fully repeatable to speed changeover for inspecting different products. 64 light level steps per light Up to 4 controllable lights per camera and power supply Set light intensity and angle in controller software Settings are saved and repeatable Over 200 CCS lighting options to choose from Compatible with Omron F150-3 and F160 vision sensors
Intelligent Lighting Adapter Dimensions

Ordering Information

Description Intelligent Lighting Adapter Camera to ILA cable Specification *For 1 or 2 channel CCS power supplies *For 4 channel CCS power supplies 6 m cable length Part number ILA-2000 ILA-4000 TCB-5-6P
*The ILA is compatible with the CCS PD series power supplies.
CCSs Intelligent Lighting Adapter combined with Omrons Vision Sensors enhances your productivity and simplifies your setup. Use the ILA with these vision sensors:
F150-3 Vision Sensor Easy-to-use 2-camera performance and lighting control with optional Windows configuration software. Contact Omron for ordering and more information on the Vision F150-3 or F160 Vision Sensors:
UNITED STATES REGIONAL SALES OFFICES
F160 Vision Sensor High-speed 2-camera mid-range machine vision performance in a compact low-cost package. Contact CCS America, Inc. for ordering the ILA and for more information on over 200 CCS lighting options:

www.omron.com/oei

OMRON ELECTRONICS LLC Technical Automation Solution Division Schaumburg, IL OMRON CANADA, INC. Scarborough, Ontario
2001 OMRON ELECTRONICS LLC
800.55.OMRON or 847.843.7900
CANADA REGIONAL SALES OFFICE Toronto 416.286.6465 BRAZIL SALES OFFICE Sao Paulo 55.11.5564.6488 ARGENTINA SALES OFFICE Buenos Aires 54.114.787.1129 MEXICO/LATIN AMERICA SALES OFFICE Florida 954.227.2121

www.ccsamerica.com

48 Weston Street, Waltham, MA 02453 Phone: 781-899-2494 Fax: 781-899-2495

SB CCS-1 6/01/7.5M