10-Device Universal Remote Control with Learning
Control Remoto Universal de 10 Dispositivos con Aprendizaje URC10820N Users Guide Gua del Usuario

Contents

Introduction.. 2. Installing Batteries.. 2 Features and Functions. 2 Key Charts.. 3. Setting Up Your Components. 5. Using Learning.. 8 Changing Volume Lock.. 9 Using Channel Scan.. 12. Programming Favorite Channel Scan.. 12 Re-Assigning Device Keys. 12 Using Keymover.. 13 Restoring Factory Default Settings. 14 Troubleshooting.. 14 FCC Compliance.. 15 Additional Information.. 15. Limited Lifetime Warranty.. 16

Contenido

Introduccin.. 17 Instalacin de las Bateras. 17. Caractersticas y Funciones.. 17 Funciones de las Teclas.. 18. Programacin de un Dispositivo (Aparato).. 20. Uso de la Funcin Aprendizaje. 23. Cambio del Bloqueo del Volumen.. 24 Uso de la Exploracin de Canales. 27. Programacin de una Exploracin de Canales Favoritos.. 27 Reasignacin de las Teclas de Dispositivos.. 27 Uso de la Funcin Keymover. 28 Restauracin de los Valores Fijados en la Fbrica.. 29 Localizacin de Fallas.. 29. Conformidad con la FCC. 30 Informacin Adicional.. 30 Garanta Limitada durante la Vida til del Producto.. 31

Introduction

The One For All 10Device Universal Remote Control with Learning (URC10820N) is pre-programmed with the latest library of codes, and it is designed to operate up to ten home entertainment devices, including TV, video, DVD, Cable, Satellite and audio components. The remote control requires four (4) new AAA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference.

Installing Batteries

1. On the remote controls back, push down on the top of the battery cover (where indicated by the arrows). Then slide the battery cover out. 2. Obtain four (4) new AAA alkaline batteries. Match the + and marks on the batteries to the + and marks in the battery case, then insert the new batteries. 3. Slide the battery cover back into place. The tab should click when the cover is locked. 4. Test the remote control by first pressing POWER and then any mode key (e.g., TV). If the batteries are inserted correctly, the LED (red light) will blink once. NOTE: When batteries are low, the remote control will blink 5 times after each key press. The remote will stop operating when the batteries need replacement. The permanent memory retention ensures that your codes are stored permanently even during battery replacement. Battery Precautions: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with Local and National Regulations.

Features and Functions

Use the Key Charts to learn how to use the universal features and functions of this remote.

Key Charts

The LED (red light), which is located underneath the POWER Key, blinks to show that the remote control is working and is sending signals. Press TV, CBL, SAT, VCR, DVD, CD, PVR, AUD, AUX1 or AUX2 once to select a desired home entertainment device to control. Press POWER once to turn on or off the selected device. For master power control, see Programming a Master Power Macro. Press MENU once to display your selected devices main menu. Use GUIDE to display your selected devices program guide or setup menu. Use EXIT to exit from your selected devices guide or menu. Use INFO to display the current channel and program information. Use the Cursor Keys to move the cursor in the program guide and menu screens. Use OK to choose options from your selected devices menu or guide. In the RCVR/AMP mode, use OK to set the surround sound. Use the up arrow (or down arrow ) to adjust the volume higher (or lower).Use the left arrow (or right arrow) to adjust the balance left (or right).
Use VOL+ (or VOL-) to raise (or lower) the sound volume. Press MUTE once to turn the sound off or on. In TV, VCR, DVD, CBL, or SAT modes, use FAV to scan favorite channels and/or all channels. (See Using Channel Scan and Programming Favorite Channel Scan.) Use CH + (or CH -) to select the next higher (or lower) channel. Press PREV once to recall the last-viewed channel and to page back one screen on the main menu. In the AUD, DVD and CD modes, use DISC to change disk (if available on your device). Use the keypad (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031). In the AUD mode, use the keypad (1 ~ 9 and 0) to select audio sources 1 through 10.
Press ENTER once after entering the channel numbers on some TVs. In the CD mode, use ENTER to add 10 to the digit entry (e.g., ENTER and 7 is 17). Use INPUT to switch the TVs input to view TV or video programs. Use the Transport Keys to control your PVR/DVR, VCR, DVD, or CD player, or VOD (Video On Demand) if available on your cable or satellite service. Press REC to record a DVD or VCR program. After programming, press M1 ~ M3 once to run a desired macro (see Using Macros). Use the L1 ~ L3 keys to learn new functions. See Using Learning for the learning feature. Use PIP to switch the Picture-In-Picture feature on or off (if available on your TV). Use MOVE to move the window picture to different positions in the main picture. Use SWAP to switch images and sound between the main and window pictures. Press SLEEP to activate your devices sleep timer (not available for all devices). Use CC to turn on closed caption or subtitles. If you have a PVR/DVR device, use SHOWS to access your list of recorded shows. Use FORMAT to change the Aspect Ratio of your display (16:9). If you have a PVR/DVR device, use LIVE to return to live programming. Use +100 if your device requires this key to access channels greater than 100 (same as your original device). Use the (-) function to access your High Definition Channels (e.g., if your HD channel is 2.5, press 2 (-) 5). Use SET for all programming sequences.

Device Table

NOTE: Please refer to this table when performing the instructions in Setting Up Your Components. After programming, this remote will be able to control the following types of devices: DEVICE KEY
CONTROLS THESE DEVICES TV (including HDTV, Plasma and LCD), TV/ DVD Combo, TV/VCR Combo Satellite, Satellite/PVR/DVR, Video Accessories (Including Media Center PCs) Cable, Cable/PVR/DVR, Video Accessories (Including Media Center PCs) VCR, DVD, DVD/R, HTIB, DVD/VCR

DEVICE KEY

CONTROLS THESE DEVICES DVD, VCR, DVD/R, HTiB, DVD/VCR
CD, Home Automation, CD/R (Recorders)
PVR/DVR Only Devices Tuner, Amp, Misc. Audio, HTiB (Home Theater In A Box) Tuner, Amp, Misc. Audio, HTiB (Home Theater In A Box) Media Center PCs, Satellite, Satellite/ PVR/DVR, Cable, Cable/PVR/DVR, Video Accessories
Setting Up Your Components
This remote is preprogrammed at the factory to operate a Sony TV, DVD and VCR, an RCA DirecTV Satellite box, a Motorola Cable Box, a Sony Tivo PVR, a Pioneer Receiver and CD, a Sony Receiver (in the AUX1 Mode), and a Microsoft Media Center PC (in the AUX2 Mode). To control devices other than the default brands, perform the following steps; otherwise skip this section. NOTE: For Combo Device control, see the next section. 1. Turn on a device (e.g., TV, VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc). NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.
2. On the remote control, press a device key once (i.e., TV, CBL, SAT, VCR, DVD, CD, PVR, AUD, AUX1 or AUX2). NOTE: Use the AUX1 key to program control of an audio device such as an AMP, HTIB (Home theater in a box), or a tuner. Use the AUX2 key to program control of a Media Center PC (with IR receiver). Alternately, use the AUX1 or AUX2 key to program control of a second device type (e.g., a second VCR; see Reassigning Device Keys).
3. Press and hold SET until the LED (red light) blinks twice, then release SET. 4. Use the accompanying code lists to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesnt work, try Searching for Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key.

6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the following boxes: TV Code: Brand Name:____________________ VCR Code: Brand Name:____________________ CD Code: Brand Name:____________________ AUD Code: Brand Name:____________________ CBL Code: Brand Name:____________________ SAT Code: Brand Name:____________________ DVD Code: Brand Name:____________________ PVR Code: Brand Name:____________________ AUX1 Code: Brand Name:____________________ AUX2 Code: Brand Name:____________________ Aux.2 Device Type:_______________ Aux.1 Device Type:_______________
Programming Combo Device Control
You can set this remote to control your combo devices such as TV/ VCR, TV/DVD, Satellite/PVR/DVR, Home-Theater-In-A-Box, and many others with a single code. For a complete list of combo devices, refer to the Device Table. NOTE: Some combo device types have codes that you can program on separate device keys. For example, you can program DVD Player/ VCR Combo codes under the VCR or DVD mode keys. See Setup Codes for DVD/VCR Combos (Cdigos de Configuracin para Aparatos Combinados DVD/ Videograbadora); note that there are two sections under this device type. To control a TV/DVD Combo: 1. Turn on the TV/DVD Combo and insert a DVD. NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.
2. On the remote control, press TV. 3. Press and hold SET until the LED (red light) blinks twice, and then release SET. 4. Use the setup codes under the TV/DVD Combos heading (use codes listed as Controlled by TV key). Locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
5. Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2 through 4, trying each code for your brand until you find one that works. If it still does not work, try Searching for Your Code.

Searching For Your Code

If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. Turn on your TV and on the remote control, press TV once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 1. The LED will blink twice. 4. Select a test function from the list below or use the default test function (POWER) and skip step 4. NOTE: The keys that can be used for the test function are 0, 1, 2, 3, POWER, VOL+, Play, Stop and MUTE.
5. Press CH+ to begin searching for your code. Stop the search when the device turns off or performs the function selected in step 4 (if other than POWER). NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. Every press of CH+ will send a new code. If you go past the code that performed the Test Function, you can go back by pressing CH.
6. To lock in the code, press and release the SET key. The LED blinks twice. 7. To search for the codes of your other devices, repeat steps 1 through 6, but substitute the appropriate device key for the device you are searching for in step 1.

Checking the Codes

If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. On the remote control, press TV once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 0. The LED will blink twice. 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e.g., three blinks =3) and write down the number in the leftmost box in the TV code boxes. NOTE: If a code digit is 0, the LED will not blink. 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Write down the code digits in the remaining TV code boxes. 6. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. Write down the devices code digits in the appropriate code boxes.

Using Learning

This remote includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g., DVD EJECT) on the L1 ~ L3 keys. However, there are some considerations.

Learning Precautions

Your original remote controls must be in working order for learning to work properly. Learned keys are mode specific, so each one can store a unique function for each mode. Learned keys can be used in macros (see Using Macros). Do not use the following keys for learning: Device Keys, SET, FAV, or Record () Key. Learning capacity is approximately 50 to 70 keys, depending on the code being learned. If both learned and keymoved functions are assigned to the same key, the last programmed function is stored. A learned function cannot be used as a source for Keymover (see Using Keymover). Certain device codes are not learnable including multifrequency types, some high frequency ones, and other unusual formats.

For optimum learning, avoid high levels of ambient light such as natural sunlight or energy-efficient fluorescent lights. NOTE: Please have your original remote controls handy before programming learning. Be sure to press each teaching key within 5 seconds of the previous entry. Otherwise, this remote exits the learning mode.
Programming A Learning Key
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 5. The LED will blink twice. 3. Press a device key once (e.g., TV) to assign a mode for learning. 4. Press the desired key once (e.g., L1) to store a feature to be learned. The LED will turn on and remain on for 5 seconds. If the LED does not turn on, go back to step 1 and start again. 5. Place your original remote control (e.g., TV remote control) head-to-head (about 2 apart) from this remote. 6. On your original remote control, press and hold the key (i.e., feature) to be learned until the LED on this remote turns off and then blinks twice. If the LED does not blink twice, repeat steps 3 through 6. 7. To learn functions onto other learning keys (e.g., L2 and L3), repeat steps 3 through 6. 8. To lock in new feature(s) on this remote, press and hold SET until the LED blinks twice, then release SET. 9. To test a learned feature, press a device key (e.g., TV) once where the learning mode was assigned. Then press the learning key (e.g., L1) where the learned feature is stored.
Deleting Functions From The Learning Keys
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 6. The LED will blink twice. 3. Press the device key once where the learned feature is stored (e.g., TV).
4. Press the learning key (e.g., L1) to be deleted twice. The LED will blink twice after the second press. 5. To clear additional functions stored on other learning keys, repeat steps 1 through 4 (in this section).

Changing Volume Lock

This remote is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a devices volume will be locked to one mode (e.g., to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.

6. Press and hold SET until the LED blinks twice, then release SET.
Programming A Master Power Macro
In its default state, the POWER key on this remote will individually power your home entertainment devices on or off. However, you can also program a Master Power Macro onto the POWER key that will sequentially turn on or off all the devices with a single key press. To 1. 2. 3. 4. 5. 6. 7. Program the Master Power Macro Press and hold SET until the LED (red light) blinks twice. Enter 5. The LED will blink twice. Press the POWER key once. For the first device you want in the power-on sequence, press its device key (e.g., TV) once. For the second device you want in the power-on sequence, press its device key (e.g., CBL) once. For the Third device you want in the power-on sequence, press its device key (e.g., AUD) once. Repeat step 6 up to seven more times to add the other desired devices to the power-on sequence (e.g., SAT, VCR, DVD, CD, PVR, AUX1 and AUX2). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET.
To Operate Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices.
NOTE: When you press POWER for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off.
2. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s).This action is normal.
Programming A Macro On A Device Key
In its default state, when you press a device key (e.g., TV) on this remote, the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receivers input to the selected device. To Program the Device Key Macro For example, lets assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receivers input to input 3 when you press and hold the DVD key. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 5. The LED will blink twice. 3. Press the DVD key once. 4. Press the AUD key (to select the receiver). 5. Press digit 3 (for the input), and press DVD (to return control to the DVD key). 6. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: You can program up to 20 functions on the Device Key Macro. You can program a device Key Macro onto any device key. To Operate the Device Key Macro 1. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receivers input to input 3, to allow you to view the DVD. NOTE: When you press the device key (e.g., DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. This allows you to still change modes while using the remote. NOTE: After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device.

Clearing A Macro

1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 5. The LED will blink twice. 3. Select a macro key (e.g., M1, M2, M3 POWER or any device key) you want to clear and press it once. 4. Press and hold SET until the LED blinks twice, then release SET. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function.

Using Channel Scan

In the TV, VCR, DVD, CBL and SAT modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed, Programming Favorite Channel Scan) and/or all channels for the selected mode. 1. Press TV, VCR, DVD, CBL or SAT once. 2. Press FAV once. If Favorite Channel Scan has been set up, scanning of favorite channels will start and cycle through stored channels, then proceed to the next channel up and cycle through all channels on the selected device. If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up and cycle through all channels on the selected device. 3. To stop scanning channels at any time, press any key once.
Programming Favorite Channel Scan
In the TV, VCR, DVD, CBL and SAT modes, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when you press FAV (see Using Channel Scan). NOTE: Only channels of one mode can be stored for Favorite Channel Scan. 1. On the remote control, press TV, VCR, DVD, CBL or SAT once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 6. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once. NOTE: If the original remote control required pressing an ENTER key to change the channel, also press the ENTER key after the channel number (e.g., 1 ENTER). 5. If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. 6. To exit programming, press and hold SET for 3 seconds. The LED will blink twice.

Re-Assigning Device Keys

You can set this remote to control a second TV, VCR, DVD player, or other device. For example, to control a TV, a cable box, and two DVDs, you will need to re-assign the unused AUX1 key to operate the second DVD as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 2. The LED will blink twice. 3. Press DVD once, then press AUX1 once. 4. The AUX1 key is now ready to be programmed for your second DVD. See Setting Up Your Components. To re-assign other device keys to the AUX1 key, repeat steps 1 through 4 by substituting the sequence from the following chart: To Re-Assign Device AUX1 as 2nd TV key: AUX1 as 2nd VCR key:
Perform Sequence SET - 9 - 9 - 2 - TV - AUX1 SET - 9 - 9 - 2 - VCR - AUX1

To Re-Assign Device AUX1 as 2nd CBL key: AUX1 as 2nd SAT key: AUX1 as 2nd CD key: AUX1 as 2nd PVR key: AUX1 as 2nd AUD key: AUX1 as 2nd AUX2 key:
Perform Sequence SET - 9 - 9 - 2 - CBL - AUX1 SET - 9 - 9 - 2 - SAT - AUX1 SET - 9 - 9 - 2 - CD - AUX1 SET - 9 - 9 - 2 - PVR - AUX1 SET - 9 - 9 - 2 - AUD - AUX1 SET - 9 - 9 - 2 - AUX2 - AUX1
You can also re-assign another unused device key by substituting an open key for the AUX1 key in the above chart and performing the sequence. For example, to re-assign an unused CBL key as a 2nd CD key, perform SET - 9 - 9 - 2 - CD CBL. When a re-assignment is done, the LED (red light) will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Setting Up Your Components).

Using Keymover

This remote includes a Keymover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode). NOTE: The following keys cannot be used as a source or destination: TV, CBL, SAT, VCR, DVD, CD, PVR, AUD, AUX1, AUX2, FAV, and SET.

Programming Keymover

For example, if your VCR does not have volume control, you can map those keys (i.e., VOL+, VOL-, and MUTE) from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 4. The LED will blink twice. 3. For the source mode, press TV once. 4. For the source key, press VOL+ once. 5. For the destination mode, press VCR once. 6. For the destination key, press VOL+ once. 7. The LED will blink twice, indicating the keymoved sequence is correct. 8. Repeat steps 1 through 7 twice more to map remaining volume control keys, substituting VOL- and MUTE as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use this remote to control the TVs volume and MUTE in the VCR mode, as well as in the TV mode.
Restoring Keymoved Keys To Default Settings
Restoring a Single Keymoved Key 1. Press a device key that has a keymoved key. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 4. The LED will blink twice. 4. Press the destination key twice (where the keymoved key is stored). The LED will blink twice.
Restoring All Keymoved Keys in a Single Mode 1. Press and hold SET until the LED (red light) blinks twice. 2. Enter 4. The LED will blink twice. 3. Press the destination mode twice (where keymoved keys are stored). The LED will blink twice.

Restoring Factory Default Settings
This remote includes a Setup Code Reset program. You can use it to restore all your programmed codes to factory settings and delete all custom programming. IMPORTANT: Executing this program erases all code settings and all custom settings including, Macros, Learned Keys, Reassigned Device Keys, Keymoved Keys, Favorite Channels, and all device settings. 1. On the remote control, press and hold SET until the LED (red light) blinks twice. 2. Enter 0. The LED will blink four times. 3. Your remote is now ready for programming.

Troubleshooting

LED (red light) does not blink when you press a key. Replace batteries with four new AAA alkaline batteries. LED (red light) blinks five times after you press a key. Replace batteries with four new AAA alkaline batteries. LED blinks when you press a key, but home entertainment device does not respond. Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. The unit does not control home entertainment devices or commands are not working properly. Try all listed codes for the device brands being set up. Make sure they can be operated with an infrared remote control. TV/VCR Combo does not respond properly. Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. Changing channels does not work properly. If the original remote control required pressing ENTER to change channels, then press ENTER on the remote control after entering the channel number. During learning, LED emits a long blink after pressing and holding key to be learned. Memory is full or a bad capture has occurred. Avoid high-ambient light sources, such as direct daylight and fluorescent bulbs. Try readjusting positions of remote controls before performing the procedure again. Tried Searching For Your Code method and still could not find a working code. Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release.Next enter 2. Then press the device key to be cleared twice.Now repeat the Searching for Your Code method. No remote control of volume. See Changing Volume Lock to lock/ unlock volume. If the above does not work. Please visit: www.oneforall.com Consumer Help Line: 1 (800) 315-0990

FCC Compliance

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
This equipment has been verified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the users authority to operate this equipment.

Additional Information

As you update your home entertainment system, One For All has a universal remote control that will fit your needs. Please visit our Website at www.Oneforall.com to see our full product lineup. ONE FOR ALL is the registered trademark of Universal Electronics Inc. Audiovox Accessories Corporation is the Licensee of the ONE FOR ALL brand for North America. Copyright 2009 by Universal ElectronicsInc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc.

Care and Maintenance

Keep the remote dry. If it gets wet, wipe it dry immediately. Use and store the remote only in normal temperature environments. Handle the remote gently and carefully. Dont drop it. Keep the remote away from dust and dirt. Wipe the remote with a damp cloth occasionally to keep it looking new. Modifying or tampering with the remotes internal components can cause malfunction and invalidate its warranty.

Limited Lifetime Warranty
Audiovox Electronics Corporation (the Company) warrants to you the original retail purchaser of this product that should it, under normal use and conditions, be proven defective in material or workmanship during its lifetime while you own it, such defect(s) will be repaired or replaced (at the Companys option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below. Do not return this product to the retailer. This Warranty does not cover product purchased, serviced or used outside the United States or Canada. This Warranty is not transferable and does not extend to costs incurred for installation, removal or reinstallation of the product. This Warranty does not apply if in the Companys opinion, the product has been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or the simultaneous use of different battery types (e.g. alkaline, standard or rechargeable). THE EXTENT OF THE COMPANYS LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANYS LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states/provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights, which vary from state/province to state/ province. U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit 3, Door 16, Mississauga, Ontario L5T 3A5

Introduccin

El Control Remoto Universal de 10 Dispositivos con Aprendizaje viene preprogramado con una biblioteca de cdigos extenso y est diseado para que controle hasta diez dispositivos del entretenimiento en el hogar, incluyendo un televisor, una videograbadora, un reproductor DVD, un receptor de cablevisin, y componentes de satlite y audio. El control remoto necesita cuatro (4) bateras alcalinas AAA nuevas (no vienen incluidas) y programacin fcil para controlar sus dispositivos. Para obtener los mejores resultados, asegurese de leer y llevar a cabo el resto de las instrucciones. Adems, conserve esta gua para una referencia futura.

CD Recorders / Enregistreurs CD / Grabadora de discos CD
CyberPower 1972 Gateway 1972 Hewlett Packard 1972 iBUYPOWER 1972 Microsoft 1972 Northgate 1972 Tagar Systems 1972 Touch 1972

Satellite / Satlite

Adcom 0577, 1100 Bel Canto Design 1583 Bose 0674 Classe 1461, 1462 Durabrand 1561 GE 0078 Harman/Kardon 0892 JVC 0331 Left Coast 0892 Lenoxx 1561 Marantz 0892, 0321 Mark Levinson 1483 Nakamichi 0321 NEC 0264 Optimus 0395 Panasonic 0521 Parasound 0246 Philips 0892 Polk Audio 0892 Realistic 0395 Sansui 0321 Shure 0264 Sony 0689, 0815 Soundesign 0078 Technics 0521 Victor 0331 Wards 0078 Yamaha 0354, 0133
CD Players / Lecteurs CD / Reproductores de CDs
Receiver / Rcepteur / Receptor
Classic 1297 Fisher 1325 GPX 1296 Harman/Kardon 1202 JVC 1294 Kenwood 0626 LG 1208 Marantz 0626 NAD 1208 Philips 0626 Pioneer 1062, 1087 RCA 0053, 0420 Sony 0000, 0100, 1364 TDK 1208 Teac 0420 Yamaha 1292
DTV Converters / Rcepteurs TV numriques / Convertidores Digitales
Accutek 1215 Amana 1716 Bionaire 0846, 1215, 1861 Frigidaire 1333 GE 0240 GoldStar 1537 Holmes 1215 Kenmore 1537 Lasko 0846, 1890 LG 1537 Lightolier 0184, 1204, 1205, 1206 LiteTouch 0084 Lutron 0597, 0318, 1239, 1597 One For All 0167 PCS 0184, 1204, 1205, 1206 RadioShack 0240 Royal Sovereign 1651 Russound 1232, 1233, 1413 Security System 0167 Sharper Image 0846 SmartLinc 0184, 1204, 1205, 1206 Universal XWhirlpool 1332 Windmere 1215 X10 0167, 2267
Audio Accessories / Accessoires de audio / Accessorios de audio

Cable / Cble

Bell ExpressVu 0775 DirecTV 1377, 0392, 0566, 0639, 1142, 0247, 0749, 1749, 1856, 1076, 1442, 1609 Dish Network System 0775, 1505, 1775 Dishpro 0775, 1505, 1775 Echostar 0775, 1505, 1775 Expressvu 0775, 1775 GE 0566 General Instrument 0869 GOI 0775, 1775 HTS 0775, 1775 Hughes Network Systems 1142, 0749, 1749, 1442 JVC 0775, 1775 Mitsubishi 0749 Motorola 0869 Next Level 0869 Panasonic 0247, 0701 Philips 1142, 0749, 1749, 1076, 1442 Proscan 0392, 0566 RadioShack 0869 RCA 0566, 0855, 0143 Samsung 1377, 1276, 1442, 1609 Sony 0639 Star Choice 0869 Tivo 1142, 1442 Toshiba 0749, 1749, 0790 Voom 0869 Zenith 1856
Accurian 1106 Altec Lansing 0607 Apple 1115 DLO 1155 GPX 2113 Griffin 1891 iDeck 1106 iHome 2152 iLive 2113 Memorex 2119 Monitor Audio 1106 Polk Audio 2228 Roku 1828 Yamaha 2021
Satellite-PVR (DVR) Combos / Combins Satellite - PVR (DVR) / Combos de Satlite-PVR (DVR)
Media Centers / Centres de mdias / Centros de entretenimiento

o n a n gn a n eg a B 0636
Home-Theatre-In-A-Box (HTiB) Ensemble home cinma Sistema de Teatro en Casa
Controlled by TV key / Contrl par la touche TV / Controlado por la tecla TV
TV-VCR-DVD Combos / Combins tlviseur - magntoscope lecteur DVD / Combos de TV-VCR-DVD
Wards 0054, 0178, 0016, 0021, 0056, 0096, 0866, 1156 Waycon 0156 Westinghouse 1712, 0885, 0889, 1282, 1577 White Westinghouse 0463, 0623 Wyse 1365 Yamaha 0769, 0833 Zenith 0017, 0463, 1265, 0178, 0092, 0016, 1929
Con o ed by AUD key Con pa Con o ado po a ec a AUD

a ouche AUD

LCD / ACL
Toshiba 1524, 0845, 1656 TruTech 1723 US Logic 1286 Viewsonic 0857, 0864, 0885, 1627, 1742, 2014, 2087 Viore 1684 Vistron 2142 Vizio 1758, 0864, 0885, 1756 Westinghouse 1712, 0885, 0889, 1282, 1577 Wyse 1365 Zenith 1265

Plasma

JVC 1923 Magnasonic 1928 Magnavox 1931 Memorex 1924, 1926, 1927 Mitsubishi 1917 Optimus 1924, 1927 Orion 1929 Panasonic 1924, 1927 Penney 1926 Quasar 1924 RCA 1917, 1922 Sansui 1929 Sears 1926 Sony 1925 Sylvania 1931 Toshiba 1918, 1936 Zenith 1929 Emerson 1944 ESA 1944 Insignia 2088 Magnavox 1944 Panasonic 1946, 1947 RCA 1953 Sharp 1917 Sylvania 1944 Symphonic 1944 Toshiba 1008 1972
Sylvania 0035, 0081, 0000, 0043, 0593, 1593, 1781 Symphonic 0000, 0593, 1593 Systemax 1972 Tagar Systems 1972 Teac 0000 Technics 0035, 0162 Teknika 0035, 0000 Thomas 0000 Tivo 0739, 0618, 0636, 1996 Toshiba 0043, 0845, 1008, 1145, 1972, 1996 Touch 1972 Viewsonic 1972 Villain 0000 Voodoo 1972 Wards 0060, 0035, 0048, 0081, 0000 XR-1000 0035, 0000 Zenith 0039, 0000, 1479 ZT Group 1972

Sharp 0807

Go V deo Huma o VC G eOn Magna o Pana on Ph p P onee Po a o d P e d an RCA am ung an o en o en e ha p on an a To h ba Zen h
Controlled by VCR key / Contrl par la touche VCR / Controlado por la tecla VCR Controlled by DVD key / Contrl par la touche DVD / Controlado por la tecla DVD
M oo M nd N eu Med a No hga e Pana on Ph p RCA Rep a TV am ung on B ue on a k9 ema Taga em T o To h ba Tou h V ew on Voodoo ZT G oup

1972 1972

DVD / Lecteurs DVD
TV-DVD Combos / Combins tlviseur - lecteur DVD / Combos de TV-DVD

1374 1495

DVD-VCR Combos / Combins lecteur DVD - magntoscope / Combos de DVD-VCR
Akai 0899 Broksonic 0868 Emerson 0821 ESA 0821 Funai 1334 Magnavox 0821 Panasonic 1362, 1462 RCA 1132 Sharp 0630 Superscan 0821 Sylvania 0821 Symphonic 0821 Toshiba 1045

1609 1390