706113_URC-6210-11_E_10t:Zapper_3

08-05-2007

Pagina 1
English Deutsch Franais Espaol Portugu s
Instruction manual.P. 2 Bedienungsanleitung.s. 10 Mode demploi.P. 18 Gua del usario.P. 26 Manual de instrues.P. 34

Italiano

Istruzioni per luso.P. 42
s Gebruiksaanwijzing.P. 50 Nederland

Magyar

Hasznlati tmutat.P. 58 Instrukcja obsugi.P. 66 Nvod k pouit.P. 74

Polski esky

URC-6210/6211
Universal remote Universal Fernbedienung Tlcommande universelle Mando a Distancia Universal Telecomando Universal Telecomando Universale Universele Afstandsbediening Univerzlis tvvezrl Uniwersalny pilot zdalnego sterowania Univerzln dlkov ovldn

Pagina 2

English

Table of Contents

INSTALLING THE BATTERIES FEATURES AND FUNCTIONS SET UP
(To set up the ZAPPER for your Television) Direct code set up Search Method Code Blink Out 7

SET-UP CODES

Television 82

TROUBLESHOOTING

Helpful Hints 8

WWW.ONEFORALL.COM

Pagina 3

Installing the batteries

The ZAPPER needs 2 new AAAA alkaline batteries. 3 Remove the battery cover from the back of the ZAPPER by pressing down on the tab. Match the batteries to the +/- marks inside the battery case, then insert the batteries. Press the battery cover back into place. Important notes: - In order to avoid having to reprogram your ZAPPER after you remove the batteries, you will need to insert new batteries within 5 minutes. Also, it is best that you do not use rechargeable batteries.

Features and Functions

1 POWER (red LED Light Emitting Diode) The POWER key operates the same function it did on your original remote control. The LED underneath the POWER key will light up red whenever a key is pressed. CHANNEL +/-, VOLUME+/- and MUTE The CH+/- and VOL+/- keys operate just as those on your original remote control. These keys are also used to set up your ZAPPER. MAGIC The MAGIC key (= setup key) is used to set up your ZAPPER.

Pagina 4

Direct code set up
To set up the ZAPPER for your Television follow the instructions below. 1 Find your Television code in the Set-Up Code section (page 82-101). Codes are listed by brand name. The most popular codes are listed first. Make sure your TV is switched on (not on standby). Press and hold the MAGIC key until the LED blinks twice (The LED underneath the POWER key will blink once then twice). Enter your 5-digit code according to the chart below. The LED underneath the POWER key will blink twice.

CHANNEL + = 3

VOLUME - = 2

VOLUME + = 1

MUTE = 5 CHANNEL - = 4
Now, aim the ZAPPER at your Television and press POWER. If your Television switches OFF, your ZAPPER should be ready to operate your device.

Pagina 5

Turn your device back on and try all the remotes functions to ensure they are working properly. If the functions do not work properly, repeat steps 1-5 using another code listed under your brand.
For example: To enter a Sony TV code 33121, you would press CHANNEL +, CHANNEL +, VOLUME +, VOLUME -, VOLUME +. If your television does not respond to the ZAPPER after you have tried all the codes listed for your brand, try the Search Method described on page 6. Make sure you write your correct 5 digit code in the boxes provided on this page.
Important notes: - Some codes are quite similar. If your television does not respond or is not functioning properly with one of the codes, follow steps 1-5 with each code listed for your brand. - If none of the codes listed for your brand operate your television, follow the Search Method described in the next section. The Search Method can be used even if your brand is not listed at all. - Write the code for your TV in the boxes provided below for easy future reference.

TV Code

Pagina 6

Search Method

If your Television does not respond to the ZAPPER after trying all the codes listed for your brand, try searching for your code. To search for your TV code: Turn on your TV. Press and hold the MAGIC key until the LED blinks twice (The LED underneath the POWER key will blink once then twice). Next, press the MUTE, CHANNEL -, CHANNEL -. Point the ZAPPER at your television. Next, alternate between POWER and CHANNEL - until your Television turns off. You may have to press these keys many times (up to 150!), so please be patient. Remember, you must aim the ZAPPER at your device the entire time you are searching for your code. When your device turns off, press and release MAGIC to store the code. The ZAPPER should now be ready to operate your Television. Turn your device back on and try all the remotes functions to ensure they are working properly. If some of the ZAPPERS commands are not operating correctly, try the search method again, you may be using the wrong code.

Pagina 7

Code Blink Out
After you have used the Search Method, you can find out which code the ZAPPER responded to by blinking back the code. Its handy to know your Television code for future reference. Remember, you can only blink back your code after the ZAPPER is operating your device. To blink out your TV code: 1 Press and hold the MAGIC key until the red LED blinks twice (the LED underneath the POWER key will blink once then twice). Next, press MUTE, CHANNEL -, CHANNEL +. For the first digit of your 5-digit code, press VOLUME + and count the red blinks. For the second digit, press VOLUME - and count the red blinks. For the third digit, press CHANNEL + and count the red blinks. For the fourth digit, press CHANNEL - and count the red blinks. For the fifth digit, press MUTE and count the red blinks.
Write the code for your TV in the boxes provided on page 5.

Pagina 8

Problem: Your brand is not listed in the ONE FOR ALL code section? The ONE FOR ALL does not operate your television?
Solution: Try the search method.
A) Try all the codes listed for your brand. B) Try the search method. You may be using the wrong code. Try Direct Set-Up again trying each code listed under your brand or start the search method over again to locate the proper code. If your original remote did not have CHANNEL +/- keys, the ZAPPER may not operate this function. Make sure you are using new batteries and are aiming the ONE FOR ALL at your device. Replace batteries with 2 new AAAA alkaline batteries.
The ONE FOR ALL is not performing commands properly?
You cannot reach channel 10 and above on your TV.
The ONE FOR ALL does not respond after pressing a key?
LED does not blink when you press a key?

Pagina 9

Customer Service
In the E-mail Fax Tel. UK : ofahelp@uebv.com (*) : +: 0901-5510010 ( 0,50 per minute) In Australia E-mail : ofahelp@uebv.com (*) Fax : 2479 Tel. : In New E-mail : Fax : Tel. : Zealand ofahelp@uebv.com (*) (06) 0508 ONE 4 ALL (255)