Onkyo TX-DS676 Manual
Onkyo TX-DS676 Home Cinema Amplifier, size: 2.6 MB
Onkyo TX-DS676 Instruction Manual
This premium A/V machine offers the same high build quality as the TX-DS777, as well as many identical cutting-edge technologies and high-performance features, such as high-current, low-impedance power amplifiers, Wide Range Amplifier Technology, IntelliVolume and a backlit learning remote. But it aims to please those with less power needs, whose spouses are reluctant to untie the purse strings far enough to get the advantages the full THX-Select enhancement package provides. Not to worry, thoug... Read more [ Report abuse or wrong photo | Share your Onkyo TX-DS676 photo ]
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Conversion plug x1 (Shape may vary depending on where the unit is purchased.)
Memory Preservation This unit does not require memory preservation batteries. A built-in memory power back-up system preserves the contents of the memory during power failures and even when the POWER switch is set to off. The POWER switch must be set to on in order to charge the back-up system. The memory preservation period after the unit has been turned off varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been turned off. This period is shorter when the unit is exposed to a highly humid climate.
THX Select Before any home theatre component can be THX Select certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select logo, which is your guarantee that the Home Theatre products you purchase will give you superb performance for many years to come. THX Select requirements define hundreds of parameters, including power amplifier performance, and pre-amplifier performance and operation for both digital and analog domains. THX Select receivers also features proprietary THX technologies (e.g. THX Mode, see page 34) which accurately translate film soundtracks for home theater playback.
Before operating this unit
Setting the AM tuning step frequency (Worldwide models only)
9 kHz 10 kHz
AM FREQUENCY STEP
AMP IN FRONT COAXIAL 1
FRONT SPEAKERS A
PRE OUT FRONT
COAXIAL 2 OPTICAL 1
Worldwide models are equipped with a switch that controls the AM band tuning steps. Please set this switch to match the AM band tuning step frequency in your area. U.S.A. and Canada : 10 kHz Other areas : 9 kHz
SUB WOOFER CENTER
OUT VIDEO-2 IN
CAUTION: SPEAKER IMPEDANCE
6 OHMS MIN. / SPEAKER
FRONT SPEAKERS B
SURROUND MULTI CHANNEL INPUT
MODEL NO. TX-DS777
S AC OUTLETS
AC 230V 50Hz SWITCHED TOTAL 100W MAX.
TAPE IN (PLAY)
Setting the Voltage selector (Worldwide models only)
Worldwide models are equipped with a voltage selector to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit. 1. Determine the proper voltage for your area: 220-230 V or 120 V. 2. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch. Slide the switch all the way to the right (120 V) or to the left (220-230 V), whichever is appropriate.
VIDEO S VIDEO OSD SELECTOR
Installing the remote controller batteries
1. Remove the battery compartment cover by pressing the tab and lifting up the cover. 2. Insert two AA (R6- or UM-3)-size batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative () symbols) inside the battery compartment. 3. After batteries are installed and seated correctly, replace the compartment cover.
Do not mix new batteries with old batteries or different kinds of batteries. To avoid corrosion, remove the batteries if the remote controller is not to be used for a long time. Remove dead batteries immediately to avoid damage from corrosion. If the remote controller doesnt operate smoothly, replace both the batteries at the same time. The life of the batteries supplied is about six months but this will vary depending on usage.
Using the remote controller
Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.
Notes Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller. Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference. Do not put any object such as a book on the remote controller. The but tons of the remote controller may be pressed by mistake and drain the batteries. Make sure the audio rack doors do not have colored glass. Placing the unit behind such doors may prevent proper remote controller operation. If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.
Remote control sensor
approx. 5 m (16 feet)
Audio equipment connections
Do not piug in the power cord until all connections have been made. On each pair of input jacks, a red connector (marked R) corresponds to the right channel, and a white connector (marked L) to the left channel. Please refer to the instruction manual of each component when making any connections. Insert the plugs and connectors securely. Remember that improper connection can result in noise, poor performance, or damage to the equipment. Do not bind audio connection calls with power cords and speaker cables. Doing so may degrade sound quality.
Audio connection cable L (Left) L R (Right) Improper Connection R
Connect your player to COAXIAL or OPTICAL, whichever appropriate.
OUTPUT (COAXIAL) Coaxial cable
MD recorder / DAT etc.
Optial fiber cable TX-DS777 / TX-DS676
Optial fiber cable
SWITCHED TOTAL 100W MAX.
CD player OUTPUT (ANALOG)
Do not plug in the power cord until all connections have been made.
(REC) OUT TAPE
Audio Connection Cable
Audio Connection Cable OUTPUT (PLAY) INPUT (REC)
Tape deck / MD recorder / DAT
1. DIGITAL INPUT connectors If your CD player has a digital output connector, connect it to a proper DIGITAL INPUT connector for clear and dynamic sound play. This unit provides four digital input connectors to connect CD players, MD recorders, DAT decks, etc. having a digital output connector. When using these connectors, connect the unit also via the audio connection cables. You should also note that the signals you can record are analog signals only. The digital inputs, COAXIAL 1, 2 and OPTICAL 1, 2can be assigned to individual input selector buttons, so when an input selector button is pressed, the assigned digital input is used instead of the corresponding analog input. (See page 23,29.) 2. OPTICAL DIGITAL OUTPUT connector (TX-DS777 only) If you have a digital recorder, such as an MD recorder, DAT, and CD-R (Compact Disc Recorder), connect the recorders digital input connector to this connector. In this case, always use commercially available optical digital audio cables. 3. Turntable This receiver is designed for use with turntables using moving magnet cartridges. Connect a ground (or earth) wire to GND terminal. With some players, connecting a ground wire results in larger noise. If so, do not connect any ground wire.
Optical digital connector
Remove the protective caps before making connections. When not in use, be sure to replace them.
AC outlet connection
You can connect the power cord from another audio device to the rear of this receiver. Since the AC outlets on the unit are a SWITCHED type outlet, you can use the STANDBY/ON button, to turn on/off the power to both this receiver and the connected audio devices. ). First turn the POWER switch ON ( The shape, number, and total capacity of the AC outlets may differ depending on the area of purchase. Make sure that the total capacity of other components connected to this unit does not exceed the capacity that is printed on the rear panel.
AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX.
Using the on-screen display
1. Press the OSD MENU button. 2. Select Speaker Setup and then press the right edge of the ENTER/Cursor button. 3. Select Config Setup and then press the right edge of the ENTER/Cursor button. 4. For the TX-DS676, go to the next step. For the TX-DS777, the display shows All Channel For THX Speakers. Select Yes and then press the center of the ENTER/Cursor button. This sets all the connected speakers to THX speakers.(The following steps are unnecessary.) Select No and then press the center of the ENTER/Cursor button to go to the next step. 5. Press the upper or lower edge of the ENTER/Cursor button to set each item and then press the right or left edge of the button to set a parameter Subwoofer: Set whether or not a subwoofer is connected. Yes: A subwoofer is connected. No: A subwoofer is NOT connected. Front : Select the size of your front speakers. Large: Large front speakers are used. Small: Small front speakers are used. Center : Select the size of your center speaker. Large: A large center speaker is used. Small: A small center speaker is used. None: A center speaker is NOT used. Surround : Select the size of your surround speakers. Large: Large surround speakers are used. Small: Small surround speakers are used. None: Surround speakers are NOT used. 6. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.
* Config Setup *
All Channel For THX Speakers =No
Subwoofer Front Center Surround
=Yes =Small =Small =Small
Setting the speaker distance
Setting the distance from each speaker to the listening position (Loudspeaker Position Time Synchronization*)
Select a value that is closest to the actual distance between each speaker and the listening position. Using the SMART SCAN CONTROLLER, you can easily set the speaker configuration. Turn it to select the setting and press it to go to the next item. For each speaker, you can set a distance of 0.3 meter to 9.0 meters (or 1 foot to 30 feet) in increments of 30 cm (1 foot). 1. Press the SP/SYS SETUP button repeatedly until Distance Setup ? appears. Press the SMART SCAN CONTROLLER. 2. Left= appears. Set the distance from the left front speaker. Press the SMART SCAN CONTROLLER. 3. Center= appears. Set the distance from the center speaker. Press the SMART SCAN CONTROLLER. 4. Right= appears. Set the distance from the Right front speaker. Press the SMART SCAN CONTROLLER. 5. R-Sur= appears. Set the distance from the Right surround speaker. Press the SMART SCAN CONTROLLER. 6. L-Sur= appears Set the distance from the left surround speaker. Press the SMART SCAN CONTROLLER. 7. SW= appears. Set the distance from the subwoofer. 8. Press the SMART SCAN CONTROLLER. The speaker distance setup has been completed.
1. Press the desired input selector button or the MULTI CH INPUT button.
The selected source name appears on the display. If you have selected DVD, CD, VIDEO 1, VIDEO 2, VIDEO 3 or TAPE, perform Digital Input Setup (see page 23). See page 33 for information on MULTI CH INPUT. See page 32 if you have selected FM or AM.
3. Start playing the selected input source.
Note: When you start playing the DVD player connected to the system, the message may appear such as PCM 48 kHz before the current encode format appears. This message is provided by the data from the DVD player, which does not indicate any product failure.
2. SP A
2 MODE AUDIO
4. VOLUME / 1. INPUT SELECTOR
1 This button allows you to set the sleep timer. (See page 31.) 2 Press this button to set the mode in which you can operate the TX-DS777/676. 3 Use this button to change the brightness of the display (normal or dim). For the European model, this button is not provided on the front panel. Change the display brightness using the remote controller. 4 You can connect stereo headphones to the PHONES jack using a standard stereo plug. (When you connect headphones, the unit will enter STEREO mode automatically and no sound will be heard from the speakers.)
If no sound is heard from the speakers, check the following items:
When you have selected DVD, CD, VIDEO 1- 3, or TAPE, check the digital input setup is correct. (See page 23.) Make sure that the input signal format setting is correct. (See page 28,29.) The Muting function may be activated. Cancel the Muting function. (See Muting the sound on page 31.) Make sure that SPEAKERS A is selected. (See Selecting the speaker system on page 30.)
Do not play CD-ROM discs that contain computer data as they may damage the speakers when the sound is amplified by the receiver.
Selecting an input source using the on-screen display
Instead of using the input selector buttons, you can use on-screen display to select the desired input source. 1. Press the OSD MENU button. 2. Select Input Selector and then press the right edge of the ENTER/Cursor button. 3. Press the upper or lower edge of the ENTER/Cursor button to select Input and then press the right or left edge of the button to select an input source. When you select DVD, CD, VIDEO 1- 3, or TAPE, set the digital input parameters on the Digital Input Setup screen. (See page 29.) When you have selected TUNER, the currently selected preset number is displayed on the next line. See page 33 for information on MULTICH INPUT. 4. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.
DVD VIDEO-1 VIDEO-2 VIDEO-3 VIDEO-4 TAPE FM AM PHONO CD
Setting the input signal format (Digital Input Setup)
The input signal format defaults to Automatic. Although you can use this default setting normally, you may change it depending on the input signal format. Ex.) Setting the input signal format for DVD 1. Press the DVD input selector button. 2. Press the DIGITAL/ANALOG button twice to display the digital input format. Press the SMART SCAN CONTROLLER. You are now able to select the input signal format. 3. By rotating the SMART SCAN CONTROLLER, select the input signal format from among Automatic, Digital, Analog, PCM, and DTS. Automatic (Automatic detection) Input signal format (Dolby Digital, DTS, MPEG, or PCM) used in the selected input source is detected automatically to execute the required decoding process. If no digital signal is input, the input signals to the analog input jacks will be played. Digital (Digital input automatic detection) Input digital signal format (Dolby Digital, DTS, MPEG, or PCM) used in the selected digital input source is detected automatically to execute the necessary decoding process. Analog (Analog audio signal processing) The audio signals input from the equipment connected to the analog input jacks are played. PCM (PCM signal processing) A decoding process is executed only when PCM signals are input. DTS (DTS signal processing) A decoding process is executed only when DTS signals are input. Notes: In Automatic or Digital mode, if the CD or LD is fast-forwarded during playback, decoded PCM signals may produce skipped sound. In such cases, change the digital audio format to PCM. If a CD or LD encoded in the DTS format is played back using PCM or Analog mode, a noise will be produced. This noise could damage the amplifier and speakers. Always use Automatic, Digital, or DTS mode when playing back DTS-encoded sources.
* Digital Input Setup * CD DVD VIDEO 1 :COAXIAL 1 Automatic :COAXIAL 2 Automatic :---Automatic
Selecting the speaker system
The TX-DS777/676 can connect to two speaker systems. You can switch between the two speaker systems by using the SPEAKERS A and B buttons. Selecting Speaker system A (SPEAKERS A indicator appears.) Press the SPEAKERS A button to turn on or off the speakers connected to the FRONT SPEAKERS A, CENTER SPEAKER and SURROUND SPEAKERS terminals. Selecting Speaker system B (SPEAKERS B indicator appears) Press the SPEAKERS B button to turn on or off the speakers connected to the FRONT SPEAKERS B terminals. Notes: Be sure to select Speaker system A during surround playback or when multi-channel input is enabled. Selecting Surround playback when both speaker systems are on automatically turns off the speaker system B. Similarly, turning on both speaker systems during Surround playback automatically sets the listening mode to STEREO.
Changing the display
The display changes each time you press the DISPLAY button during playback. (The European model allows you to receive RDS broadcasts. See page 46 for details.)
Preset station name (Does not appear if no name is given.)
Preset input source name (Does not appear if no name is given.)
During Dolby Digital, DTS or MPEG playback, the input signal format for the playback software appears.
For analog signals, Input source name or Listening mode can be selected. Input signal format returns to Listening mode within three (3) seconds.
Input signal format: Current sampling frequency displays for PCM signals (ex. PCM 44.1 kHz). No correct information displays, however, for the frequencies other than 32, 44.1, 48, and 96 kHz. For Dolby Digital/DTS/MPEG, the surround channels information may also display. For example, Dolby D 3/2 indicates that the source outputs signals for three front channels and two surround channels in Dolby Digital mode.
Muting the sound (Muting function, remote controller only)
Use this function to turn off the playback sound immediately. For example, you can use it when you receive a phone call when listening to music. Press the MUTING button. The display shows "Muting." Now the sound output to the speakers and headphones stops. Press the MUTING button again to turn on the sound output. Note: The Muting function will be canceled automatically if the receiver is set in the standby mode.
Falling asleep with music (Sleep function, remote controller only)
You can turn off the power to the TX-DS777/676 automatically after a specified time period. 1. Press the MODE AUDIO button. 2. Press the SLEEP button. The display shows Sleep 90min, which means the receiver automatically enters the standby mode after 90 minutes. 3. Press the SLEEP button repeatedly until the desired sleep time is displayed. Each time you press this button, the time decreases by 10 minutes. To check how much time is left before the unit turns off. Press the SLEEP button when the Sleep function is enabled. Note: Pressing the SLEEP button when the Sleep time display shows 10 minutes or less cancels the Sleep function.
** Multi Ch Input ** Level Setup Left Center Right Left Sur Left Sur Subwoofer = 0dB = +5dB = 0dB = 0dB = 0dB =+10dB
1. Press the OSD MENU button. 2. Select Input Selector and press the right edge of the ENTER/Cursor button. 3. Press the right or left edge of the ENTER/Cursor button to select MULTI CH. Then, press the center of the ENTER/ Cursor button. The Multi Ch Input screen appears. 4. If you wish to skip assigning a video source, proceed to step 5. To assign a video source, select Video Assign Setup and then press the right edge of the ENTER/Cursor button. When Video Assign Setup screen appears, move the cursor (which is already located at MULTI CH) rightward or leftward to select the video source you wish to assign. When selected, press the center of the ENTER/Cursor button to return to the previous screen. 5. Select Level Setup and press the right edge of the ENTER/ Cursor button. "Multi Ch Input Level Setup" screen appears. 6. Press the upper or lower edge of the ENTER/Cursor button to select the item. Then, press the right or left edge of the button to select the desired parameter. At the listening position, adjust the speaker output level so that you can hear the same sound volume from all speakers. For the right front, left front, center, right surround and left surround speakers, the output levels can be adjusted within the range of -12 dB/+12 dB. The adjustment range of the subwoofer, however, is -30 to +10 dB. 7. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.
Using the Listening Modes
Before Using Listening Mode Listening Modes
The TX-DS777/676s surround sound enables you to enjoy the presence of a movie theater or concert hall in your room. Before using a listening mode, make sure the Speaker Setup parameters have been set (refer to page 18 ~ 23). Once the parameters have been set, it is not necessary to set them again. The configuration of the speakers are very important for the surround sound. Refer to connecting speakers on page 10. sounds, vocals, and jazz music. By emphasizing the front stereo image, it will simulate the acoustics in front of the stage. STUDIO-MIX : This mode is suitable for rock and popular music. Lively sounds with a powerful acoustic image will make you feel as if you are in a club. 5CH STEREO : This mode is useful for background music. The front and surround channels will create a stereo image. TV LOGIC : This mode offers a realistic acoustics of a TV program being aired in the TV studio. It enhances the entire surround sound and clarity of conversation. DIRECT : This mode delivers pure sound with the minimum sound quality adjustment and filtration. To attain it, the sound recorded for the Right and Left front channels is output to the Right and Left front speakers only and not output to the subwoofer. STEREO Select this mode when you do not wish to use the surround mode. All input sound is output from the front speakers.
DOLBY DIGITAL Surround, DTS (Digital Theater System), MPEG Surround
This 5.1-channel digital surround format enables you to individually record and play five full-range (20Hz20kHz) channels (left and right front, center, two surround channels) plus an LFE channel (Low Frequency Effect) for the low-range effect sound. It will create a realistic sound that could be heard in the theaters and concert halls. DOLBY DIGITAL: Select this option when you play a DVD video mark. that has a DTS: Select this option when you play a DVD player, video disc, or mark. CD that has a MPEG(European model only):Select this option when you play a mark. DVD video that has a
A system with L/R front and center speakers
The following modes are available: DOLBY 3 STEREO The surround channel sound is output from the left and right front speakers. STEREO This is a normal stereo mode. Surround mode is cancelled. DIRECT See the description above.
DOLBY PRO LOGIC Surround
This surround format consists of four channels (left and right front, center, and monaural surround channels) and emphasizes the center channel. This format is very effective for panning music, conversation, and three-dimensional sound movement output from three front channels. It also simulates the atmosphere and surround effects of the sound reflected from the side and rear walls of the theater. Select this option when you play a VHS, VHS Hi-Fi, laser mark. disc, or DVD video that has a
A system with L/R front speakers
The following mode is available: STEREO This is a normal stereo mode. DIRECT See the description above.
Home THX Cinema Surround(TX-DS777 only)
DOLBY DIGITAL/DTS/DOLBY PRO LOGIC/MPEG THX CINEMA In these modes, Dolby Digital/Dolby Pro Logic/DTS or MPEG Surround is reprocessed using a technique called Home THX processing. Home THX processing was developed by the surround engineers at Lucasfilm Ltd. for accurate reproduction of soundfields in the home environment as the filmmaker intended, equivalent to those obtained in a well-furnished movie theater. For Home THX Cinema Surround playback, we recommend that you use a THX speaker system certified by Lucasfilm Ltd. (such as Onkyo's THX speaker system HTS SYSTEM-2).
DSP (Digital Signal Processor)
The DSP converts the audio signals into digital audio format to create sound reflection. This yields an effect that makes you feel like listening to a live performance. The following illustration shows how reflected sound reaches the audience in a concert hall. Onkyo's DSP and advanced technologies let you get such a sound reflection effect from the unit. Note: The concert hall effect is produced from the reflections and reverberations contained in the original recording. These are converted into reflected sound that is reproduced from four directions. Thus, in some cases an unnatural impression can be conveyed if there are too few reflections in the recording or if the effects in the original recording were produced artificially. Example: Sound reflection in a concert hall
TX-DS676 European model
LISTENING MODE DIRECT STEREO /DTS/MPEG 5CH STEREO DSP
TX-DS 676 Others
LISTENING MODE DIRECT STEREO /DTS 5CH STEREO DSP
Selecting an Listening mode using the on-screen display
Instead of using the Listening mode buttons, you can use on-screen display to select the desired input source. 1. Press the OSD MENU button. 2. Select Input Selector and then press the right edge of the ENTER/Cursor button. 3. Press the upper or lower edge of the ENTER/Cursor button to select Listening mode and then press the right or left edge of the button to select an listening mode. 4. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.
Input sources and listening modes
The available listening modes vary depending on the input source. The following table shows each input source and the available listening modes. *Available for TX-DS676. Input source Listening mode Stereo (3 Stereo) * Dolby Pro Logic * THX Cinema Action Musical Mono Movie Orchestra * Unplugged * Studio-Mix * TV Logic * 5ch stereo * Direct * Dolby Digital * THX Cinema Action Musical Mono Movie Orchestra Unplugged Studio-Mix TV Logic Dolby Digital Pro Logic * Action Musical DTS/MPEG * THX Cinema Action Musical Mono Movie Orchestra Unplugged Studio-Mix TV Logic MPEG Pro Logic * Action Musical analog/PCM O O O O O O O O O O O O Dolby Digital 3/2ch 2/0ch O O DTS O 3/2ch O MPEG 2/0ch O
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
For Dolby Digital and MPEG, only typical input signals are shown here. 3/2ch, for example, means that the source outputs signals for three front channels and two surround channels. The available listening modes vary depending on the input signal. The table shown above lists the input sources and listening modes available when the speakers are installed in a full configuration (right/left front, center, and right/left surround speakers).Without surround speakers, set the listening mode to STEREO (3 Stereo) or Direct.
Setting the listening mode parameters
How to set the listening mode parameters
To set the listening mode parameters, you first press the AUDIO ADJUSTMENT button to select the item and then rotate the SMART SCAN CONTROLLER to select the parameter. 1. Select the listening mode for which you wish set parameters. 2. Press the AUDIO ADJUSTMENT button until Frt Effect=. appears. The parameters you can set vary depending on the selected listening mode. You can press this button to display the available parameters one by one. 3. Rotate the SMART SCAN CONTROLLER to change the parameter setting. 4. Press the SMART SCAN CONTROLLER.
PUSH TO ENTER PUSH TO ENTER
If you use the on-screen display to set a listening mode, you can set the relevant parameters on the same screen. 1. Press the OSD MENU button. 2. Select the Listening Mode and press the right edge of the ENTER/Cursor button. 3. Press the upper or lower edge of the ENTER/Cursor button to select Listening Mode. Then, press the right or left edge of the button to select the listening mode. The parameter items available for the selected listening mode are displayed. 4. Press the upper or lower edge of the ENTER/Cursor button to select the item and then press the right or left edge of the button to set a value. If you select LFE Level, Setup, etc., an additional screen will appear. Set the value for each item in the similar manner. 5. Press the center of the ENTER/Cursor button, or the EXIT RETURN button, to exit the setup mode. Default: Select Default to reset each parameter to the factory-set default.
Receiving RDS broadcasts
RDS reception is available only on the European model, and only in areas where RDS broadcasts are available. PS:
(European models only)
What is RDS?
FM broadcasting stations now transmit RDS signals, which provide additional information. RDS provides you with various services so that, for example, you can choose a station broadcasting your favorite categories of music or other information. (Refer to the right column for details.)
Program Service Name When an RDS station broadcasting PS information is selected, the stations name is displayed instead of the frequency. PTY: Program Type When an RDS station broadcasting PTY information is selected, the station type (classification) is displayed. TP: Traffic Program When an RDS station broadcasting TP information is selected, the traffic information is displayed. RT: Radio Text When an RDS station broadcasting RT information is selected, the information received from the station is displayed. Notes: In some cases, the characters displayed on the TX-DS777/676s display may not be exactly the same as the ones broadcast by the radio station. Unusual characters may appear on the display if the TXDS777/676 receives characters that cannot be displayed correctly. This is not a malfunction.
PTY Classifications in Europe None News reports Current affairs Information Sport Education Drama Culture Science and technology Varied Pop music Rock music Middle of the road music Light classics Serious classics Other music Alarm No program type. Reports on current events and happenings. Topical reporting of current affairs, often with a wider range of topics than news reports. General information such as whether forecasts, consumer affairs, medical help, etc. Live sports action, sports news, and interviews. Formal educational programs. Radio plays and serials. Cultural programs (including religious affairs). Programs about the natural sciences and technology. Speech-based programs not covered by the above categories (e.g., quizzes, panel games, comedy, etc.). Popular commercial music, usually from past or present sales charts (e.g., Top 40). Popular music with an alternative appeal, often not appearing on sales charts. Easy listening music (as opposed to Pop, Rock or Classical). Classical music for general rather than specialist appreciation. Performances of major orchestral works, symphonies, chamber music etc., including Grand Opera. Music styles not covered by the above categories, e.g. Jazz, Rhythm & Blues, Folk, Country, Reggae. When an RDS station is making an emergency broadcast, this ALARM will flash on the display.
The remote controller codes for the Onkyo CD player, tape deck, DVD player, and MD recorder have already been programmed into the buttons on the RC-392M. You may program other remote controller codes into these buttons. If you wish to restore the Onkyo preset codes after you program new codes, erase the new codes. (See page 53.)
Note: The remote controller has 408 memory slots (51 buttons 8 modes), although this number varies significantly depending on the manufacturers and types of the remote controller you wish to program into the RC392M. It is recommended that you determine which button functions have priority for programming. If you do not press any button for more than 30 seconds during the procedure, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume Step 2. If you make a mistake during programming, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. If you try to program beyond the learning capacity of the RC-392M, the SEND/LEARN indicator flashes six times quickly, then the RC-392M exits Learning function. Try programming in a button of other MODE. Follow the same procedure when you wish to program new codes into the already-programmed buttons. This remote controller uses infrared rays. Most remote controller codes can be memorized using the infrared system; however, depending on the degree to which the system differs, there may be some rare occasions when memorization is not possible. Some remote controllers use a single button to perform different functions, with the function code changing each time the button is pressed. If you are using this kind of controller, please perform the learn operations for each function individually to store each function to a button on the RC-392M. For instructions regarding the operation of learned units, please refer to the instruction manual for each product. Even after codes have been memorized, please keep your old remote controller in a safe place. If the memorized codes are lost when the batteries run down, it will be necessary to memorize them once again using the old remote controller. Make sure both the RC-392M and the products own remote controller have fresh batteries. If either of them has batteries that are wearing down, it may be impossible to store the remote controller codes into the RC-392M or the product may not respond properly to the buttons on the RC-392M for which the remote controller codes were stored into memory.
RE SU D O M
See page 57 for information on how to erase the learned codes from all buttons.
Erasing a learned code
You can erase a learned code. You cannot erase preset codes. Erasing a code programmed in a button 1. Press and hold down the corresponding MODE button and press the ENT button, then release the buttons. When you press the MODE button, the SEND/LEARN indicator lights up. When you press the ENT button, the indicator turns off. When you release the buttons, the indicator lights up again. 2. Press and release the button from which you wish to erase the learned code. When you press the button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights up again. 3. Press and release the same button again. The SEND/LEARN indicator flashes twice slowly. The learned code is erased.
POWER Power shut off immediately after power on. No power.
31 23, 29 6~15 26, 11 34~18, 22
Power on but no sound.
Amplifier protection circuitry has been activated. Power cord is disconnected. There is external noise in the computer circuits of this unit. AC fuse blown. Muting is displayed. The digital/analog input setting is incorrect. Bad connections. Amplifier protection circuitry has been activated. The input selector is not set properly. The TV (or monitor) is not set to receive the output signals from the reciver. The video cable is not connected securely. Only S video connection is made. Speaker cable is not corrected. Listening mode is set to Stereo or Direct. CENTER level is set to minimum. CENTER SPEAKER is set to None. Subwoofer is set to No. Subwoofer speakers output level setting is improper.
Remove the AC plug from the outlet immediately. Then contact your Onkyo service center. Connect power cord. Turn the power button off and then on again or remove the AC plug from the outlet and then plug it again. Contact your Onkyo Service Center. Press the MUTING button on the remote controller to turn it off. Select the correct input. Check connections, speaker leads, etc. Contact your Onkyo Service Center. Set it to the playback source. Set the TV (or monitor) to the receiver input. Check the connections. Make also video connection. Check the connection between the amplifier and the speaker. Set the Listening mode to any mode other than Stereo or Direct. Set the CENTER level to the appropriate volume. Set CENTER SPEAKER to Large or Small. Check the speaker setting. Check the output level of the Subwoofer using the test tone. Check outer conductor of input plugs. Check for proper ground connection. Adjust the placement of the cable to reduce hum. Move them farther apart. Replace. Clean. Turn treble control down. Connect the included AM loop antenna to the AM antenna terminals. Move the AM loop antenna to different position. Set up an outdoor AM antenna.
The sound of the playback source is not heard. No picture appears on the TV screen (or monitor) SPEAKERS No sound from the center speaker, or very minimal sound.
No sound or quiet sound from subwoofer PHONO Hum, low-frequency noise.
Howling when the volume is turned up. Rough or scratchy sound. High range is not clear. FM/AM AM stations cannot be received. Buzzing noise on AM (particularly conspicuous at night or with weak stations). High-pitched noise or buzzing noise on AM. Crackling noise on AM, FM.
(The MPEG indicator appears on the European model (TX-DS777/ TX-DS676) and the worldwide model (TX-DS777) only.)
f. g. h. i. j. k.
Memory indicator RDS station received indicator (European model only) FM Stereo indicator Tuned indicators Auto indicator Multi function display (Frequency and Preset station/Input selector/Sleep time/ Volume level/Listening mode)
Using the remote controller, you can control a CD player or cassette tape deck connected to the connector of the TX-DS777/676. (See page 7 for more information.) 1. SEND/LEARN indicator [49, 52, 53] 2. POWER ON/STNBY button [13, 49, 50, 54, 57] Power on/Standby on 3. SLEEP button [27, 31, 49] Sleep function button 4. MACRO DIRECT button [55, 56] Macro Direct function 5. MODE buttons [13, 27, 49~56] 6. DISPLAY/DVD SET button [49, 50] 7. CH +/ buttons [32, 49] 8. EXIT/RETURN button [16, 17, 50] 9. PREV CH button [This button is not used for this receiver.] 10. TRACK button  11. CD/TAPE/DVD/MD operation buttons [50, 51] 12. Input Selector buttons [27, 32, 35, 49] 13. Numeric key/STEREO/DSPa, s/SURROUND/SPA, B/CH SEL/LEVEL+,/DIMMER buttons [21, 27, 33, 35, 42, 49~51] [The THX button are not used for the TX-DS676.] 14. ENT button [50~53, 57] 15. DISC button  16. MUTING button [31, 32, 49, 50] 17. TEST/TV/VCR button  18. ENTER/cursor buttons [16, 17, 50] 19. VOL / button [27, 35, 49, 50] Volume adjustment 20. OSD/MENU button [16, 17, 50] 21. MACRO MODE button [54, 56] 22. LIGHT button 
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-833-5222 http://www.onkyo-intl.com ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com
This premium A/V machine offers the same high build quality as the TX-DS777, as well as many identical cutting-edge technologies and high-performance features, such as high-current, low-impedance power amplifiers, Wide Range Amplifier Technology, IntelliVolume and a backlit learning remote. But it aims to please those with less power needs, whose spouses are reluctant to untie the purse strings far enough to get the advantages the full THX-Select enhancement package provides. Not to worry, though. With Cinema Re-EQ, complex circuitry licensed by Lucasfilm, and a beefy 115 watts x 5 of ultra-wide bandwidth power into 6 ohms, the only domestic discord you'll have is deciding which DTS-encoded DVD movie to watch. This receiver features MPEG decoding for full compatibility with MPEG-encoded software and broadcasts. 96 kHZ/24-bit DAC high-resolution digital conversion circuitry not only supports the upcoming DVD-Audio and Super Audio CD audio platforms, its faster and higher-rate conversion can benefit all of your regular CDs and DVDs as well. In addition to offering simple and fast surround setup, Onkyo's SSC (Smart Scan Controller) gives you significantly increased flexibility by allowing you to perform less frequently needed functions with a simple-to-use knob in conjunction with display prompts. S-Video inputs (1 front-panel) and outputs let you maximize the full potential of high-resolution video sources. The TX-DS676's large terminals for all channels allow you to install higher quality cables to your system and get better performance, and they're spaced to accept dual banana plugs, for quick, easy connection. Overlapping menus (just like your computer) and uncomplicated graphic illustrations make it easier than ever to navigate through functions and set up parameters. A superimpose mode lets you see the onscreen display over your TV picture.
|Product Type||AV receiver|
|Dimensions (WxDxH) / Weight||AV receiver : 17.1 in x 17.8 in x 6.9 in / 32.4 lbs|
|Sound Output Mode||Surround Sound|
|Built-in Decoders||Dolby Pro Logic, Dolby Digital, DTS decoder|
|Digital Sound Processor (DSP)||Yes|
|Surround System Class||5.1 channel|
|Response Bandwidth||20 - 100000 Hz|
|Signal-To-Noise Ratio||100 dB|
|Output Power / Total||575 Watt|
|Input Impedance||50 kOhm|
|Input Sensitivity||200 mV|
|Total Harmonic Distortion||0.08%|
|Amplifier Output Details||85 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.08% - 1 channel(s) ( center ) 85 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.08% - 2 channel(s) ( front ) 85 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.08% - 2 channel(s) ( rear ) 110 Watt - 6 Ohm - 20 - 20000 Hz - THD 0.1% - 1 channel(s) ( center ) 110 Watt - 6 Ohm - 20 - 20000 Hz - THD 0.1% - 2 channel(s) ( front ) 110 Watt - 6 Ohm - 20 - 20000 Hz - THD 0.1% - 2 channel(s) ( rear )|
|Additional Features||On-screen display, A-B speaker switch, Midnight Mode|
|Type||Radio tuner - AM/FM - digital|
|Tuner Frequency Range||FM: 87.5 - 108 MHz, AM: 530 - 1710 kHz|
|Tuning Display||Fluorescent display|
|Preset Station Qty||40 preset stations|
|Antenna Form Factor||Loop AM / wire FM|
|Response Bandwidth||30 - 15000 Hz|
|Signal-To-Noise Ratio||76 dB|
|Total Harmonic Distortion||Mono: 0.2%, stereo: 0.3%|
|Station Memo Display||Yes|
|Type||Universal remote control - infrared|
|Features||Joystick, macro function, programmable, back-lit buttons|
|Connector Type||1 x headphones ( phone stereo 6.3 mm ) - front 1 x S-Video input ( 4 pin mini-DIN ) - front 1 x composite video/audio input ( RCA phono x 3 ) - front 4 x front speakers output ( banana/spade x 2 ) - rear 1 x center speaker output ( banana/spade x 2 ) - rear 2 x rear speakers output ( banana/spade x 2 ) - rear 1 x remote control - rear 1 x AM antenna ( click-fit x 2 ) - rear 1 x FM antenna ( F connector ) - rear 1 x monitor output ( 4 pin mini-DIN ) - rear 1 x monitor output ( RCA phono ) - rear 4 x S-Video input ( 4 pin mini-DIN ) - rear 2 x S-Video output ( 4 pin mini-DIN ) - rear 4 x composite video/audio input ( RCA phono x 3 ) - rear 2 x composite video/audio output ( RCA phono x 3 ) - rear 3 x audio line-in ( RCA phono x 2 ) - rear 1 x audio line-out ( RCA phono x 2 ) - rear 1 x 5.1 channel audio line-in ( RCA phono x 6 ) - rear 1 x 5.1 channel audio line-out ( RCA phono x 6 ) - rear 2 x SPDIF input ( RCA phono ) - rear 2 x SPDIF input ( TOSLINK ) - rear|
|Included Accessories||AM antenna|
|Cables Included||1 x antenna cable|
|Power Device||Power supply - integrated|
|Power Outlets||2 AC outlets|
|Service & Support||2 years warranty|
|Service & Support Details||Limited warranty - parts and labor - 2 years|
|Universal Product Identifiers|
Ecmp10 DSR-400K 268 Dtca8 Roland CY-8 Wiffle Ball Lexmark X652 EWT10120W XM-440EX Logicom G650 TH-42PX600 A 9002 Touch NF-95 Express 3 115 T CE292DN Garmin Nuvi KDC-W7534U RX-V440 Bronco-1996 HTS8100-37B Argos Deskjet 692K HT-SS370 TL-WN422G Moteur RTS FC6095 Gradius V RS2577SL Remote XV-DV424 HT503 K2000 ZI918 12K System-2005 SU-8055 26LC2R Tourer GS500 Magic Designjet 4500 Readimanagerse200 VS2321 EM325 VLA424 3-0-0 Mixer SET WD-80180NU LA40S81B TXL32X10YA LE40B652 CDX-GT210 HL-EL210 Maxxbass CQ-C1100H CQ-C1121U CMT-HPZ9 MG-396WA GPS 45XL DB178RMP KX-TGA830RU T8510 Magnia Z310 SAT M1 HA-830 DAV-DZ330 WDJ1285 Omnia II Network User DSC-W150 TX-NR900E 60 CT-1 PD110 V8M800 Review VP-L800 LN55B650 Piranhamax 10 CLD-900 BHD-5 Print 1210XI 17BII CP1510 HCD-C450 R730-JA02 P5P800-MX LQ-2190 E500-PIB Modem Sbchc8440-00 OT-208A Digitech RP70 VN-480PC TDR125-2002 CS-55P 193P Plus KDC-MP632U Seiko H023 LH-RH9509TA Elna 744
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101