Reviews & Opinions
Independent and trusted. Read before buy Orbit Watermaster 57114!

Orbit Watermaster 57114

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page 

Download (Spanish)
Orbit Watermaster 57114, size: 516 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Orbit Watermaster 57114Orbit Irrigation 57114 4-Stn Stand Indoor CONTROL; GBX
Independent dual watering programs. Day of week and watering intervals. Up to eight start times per valve, ideal for new lawns and drip irrigation. Station run time 1 to 99 minutes. Built-in calendar keeps track of odd/even days and leap years.

Details
Brand: ORBIT
Part Numbers: 2845170, 533452, 57114, 7095045, 711894, No 57114
UPC: 00046878571143, 046878571143, 46878571143

 

[ Report abuse or wrong photo | Share your Orbit Watermaster 57114 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

WTM230158 57114-14 rF_Eng.qxd

12/10/2002

1:50 PM

Page 1

Weak or missing batteries can cause the time and date to be erased after a power failure.
Installation Manual / Users Manual
Sprinkler Timers by Orbit
Set the Time of Day and Date
If this is the first time the Timer has been programmed, you should press the small recessed button labeled RESET. Pressing RESET does not affect the factory installed fail-safe program [See Figure 2].
FIGURE 7: LCD Display with Watering Interval
FIGURE 2: Programming Keys
Press and hold the + or - keys to select the number of days between watering. Example: If you want to water once every 10 days, set the interval at 10. To activate the watering interval, press ENTER. Note: If an interval of 3 is entered today, the Timer will water for the first time today, and then again every 3 days. To select odd or even day watering, press NEXT. The cursor will move to either the odd or even setting, then press ENTER. To erase a schedule, press CLEAR. To enter a new schedule, press NEXT.
Turn the rotary dial to the TIME/DATE position [See Figure 3]. 12:00 AM will appear in the display with three arrows pointing to the year, month, and day. Use the + and - keys to set the correct time of day. When the correct time of day is reached, press the ENTER key to lock in the time. To increase or decrease more rapidly, hold down either the + or keys until the display goes into rapid advance mode. A blinking cursor will appear below the arrow for the year, month, and date when programming [See Figure 3]. Use the + and keys to set the correct year, then press ENTER. Use the + and keys to set the correct month, then press ENTER. Use the + and keys to set the correct date, then press ENTER.
Reviewing and Changing Your Program
The Orbit Timer lets you easily review a complete watering plan. For example, to review Program-A watering start times, simply turn the rotary dial to the CYCLE START TIMES position in Program-A and check the times that have been entered. Using the NEXT key, you can advance through the schedule without fear of disturbing any programming. If you want to change the start times, watering days, or interval, simply follow the directions for that program. After reviewing or changing a watering schedule, remember to turn the rotary dial back to AUTO.
FIGURE 3: LCD Display with Surrounding Information
Ready for Automatic Operation
After programming is complete, turn the rotary dial to AUTO [See Figure 8]. The Timer is now fully programmed and ready to use in the automatic mode. In automatic mode, each program will operate sequentially, starting with Program-A.

MODELS

57114, 57161, 57162, 57242, 91046, 91054, 94122, 94124, 94126
Caution: If a watering schedule is not entered into the Timer, the factory installed fail-safe program will turn on each station every day for 10 minutes. To avoid accidental valve activation, either turn the rotary dial to OFF or enter a watering schedule.
Establish a Watering Schedule
To help you visualize how best to program the Timer, it might be helpful to make a watering plan on paper. This will help you establish which days and times you want to water.
FIGURE 8: Ready for Automatic Operation

version

section

Introduction

Programming
Thank you for selecting an Orbit sprinkler Timer. Orbit designers have combined the simplicity of mechanical switches with the accuracy of digital electronics to give you a Timer that is both easy to program and extremely versatile. The Orbit Timer provides convenience and flexibility, letting you run a fully automatic, semi-automatic, or a manual watering program for all your watering needs.
The Timer has two programs you can setup to control a variety of watering schedules. Depending on your needs, you can use either or both programs.
The Orbit Timer has the ability to override the automatic program without disturbing the preset program.
Semi-Automatic & Manual Operation
Enter Watering Schedule in Any Order
Using the Semi-Automatic Mode
(All stations cycle once both A & B programs) Turn the rotary dial to AUTO, then press the MANUAL key. The display will show AB, MANUAL, and ALL will be blinking [See Figure 9]. This indicates all stations will semi-automatically water for their assigned durations in sequence. To activate the assigned water durations in the A and B programs for each station, press ENTER.
FIGURE 9: Semi-Automatic Watering for Stations Assigned to A and B

Please read this manual completely before you begin to program and use the controller. A few of the most notable design features include:
You have the option of entering your watering schedule in whatever order you like. This feature makes it very easy to review and change your watering schedule. Your settings can be changed at any time while youre setting up the initial schedule or even after years of operation.

At-a-Glance Simplicity

By turning the rotary dial to one of nine settings you can review programming or easily make changes.
Start Times for Program A or B
Note: A start time is the time of day that the program begins watering the first station, and all other stations in the program will then follow in sequence. There are not separate start times for each station. Start times do not correspond to specific stations, but to programs (A or B). If you enter more than one start time, all stations in the specified program will water again (in sequence). The way you set the cycle start time is the same for both programs. Turn the rotary dial to the CYCLE START TIMES position in the program that you want to set. The display will show an A or B depending on which program you have selected. The display will show : and a blinking cursor in CYCLE START 1 location [See Figure 4]. Set the time you want to begin watering for start time 1 using the + or keys, then press the ENTER key. The display will advance to START 2. For additional start times, simply repeat this procedure by using the + and keys to enter the time and then press ENTER. Remember, Each start time will activate all stations that are set to water in the specified program. There are not separate start times for each station. Start times do not correspond to specific stations. Up to four start times can be entered per program (A or B).

Arm Chair Programmable

By inserting two AA alkaline batteries you can program the Timer prior to installing it in its permanent location.
The 0.75 amp slow-blow fuse provides circuit protection. For replacement, use WaterMaster 0.75 amp fuse or equivalent.

Programs

Lexan Language Covers
Available in English, French, Spanish, Italian, German.

1. Digital Display

A large LCD (Liquid Crystal Display) shows the time of day and indicates many of the programming settings. The display is completely interactive with all other controls.
Note: Water durations assigned to station 1 in program A will water first, then move to station 1 in program B before advancing to the second station and will continue alternating. Only those stations assigned a watering duration will water when using the manual or semi-automatic mode [See Figure 10].
FIGURE 10: Semi-Automatic Watering Entered for A and B Programs, All Stations

2. Programming Keys

The Timer has seven push button keys for setup and program entry. Working in conjunction with the rotary selector, the keys are used to set the time of day, watering time, watering days, start times, and other functions.
FIGURE 1: Location of Controls on the Timer

3. Selector Dial

This large dial makes it easy to see which function is currently selected and/or in which mode the Timer is set to operate.
FIGURE 4: LCD Display with Start Time

4. Reset Button

The reset button clears the time, date and user-defined programming but does not remove the factory installed fail-safe program. To prevent an accidental reset, the button is recessed into the panel and must be pressed with a small pointed object such as a pen or pencil tip.
Water Duration for Program A or B
Note: Both programs require watering durations to be programmed. Turn the rotary dial to ZONE DURATION position in either the A or B program. The display will show which program you have selected with an "A" or "B" and the - - cursor blinking at station "1" [See Figure 5].
(All stations cycle once, A program only) To activate stations assigned watering duration for the A program only, press the MANUAL key, followed by the NEXT key. This will activate stations with assigned watering durations in the A program only. To initiate this semi-automatic watering, press ENTER [See Figure 11]. (All stations cycle once, B program only)
Notable Programming Features
Two Watering ProgramsSummary
The Timer gives you the option of using one or both of the independent programs. Note that each station can independently be set to either A or B or both A and B programs.
To activate stations assigned watering durations for the B program only, press the MANUAL key, followed by pressing the NEXT key two distinct times. This will activate only those stations with assigned watering durations in the B program only. To initiate this semi-automatic watering, press ENTER.
FIGURE 11: Manual Watering in Either the A or B Program Only

ProgramA

This program lets you schedule selected stations to water on specific days of the week or to water every 2nd day. Program A repeats itself continuously in successive weeks.

FIGURE 5: Station Duration for Program A

ProgramB

Provides two options: One for odd or even day watering or for intervals ranging from everyday to every 28th day. This feature is designed to meet the growing needs and restrictions imposed by local governments and to conserve water. The Timer automatically calculates odd and even days (by date) for each month and makes adjustments for leap years to provide true odd and even watering through the year 2100.

Start-Time Stacking

The Timer has the intelligence to stack start times that overlap. If you enter two or more start times that overlap (in the same or in different programs), the Timer will not activate two stations at the same time. Instead, the Timer activates the first station and then activates the next station(s) in sequence after the first station finishes its preset watering duration. The Timer will NOT stack to the next calendar day. This prevents the Timer from violating an odd or even day watering schedule.
You can set the watering duration from 1 to 99 minutes. Press and hold the + key to advance the number of minutes, or use the - key to go in reverse, then press ENTER. When the minutes are set, A or B will appear over station 1 and the cursor will advance to station 2 and begin blinking. Simply repeat these steps to set watering durations for all zones on this program To skip a station, press the NEXT key. To erase previously programmed watering durations, press the CLEAR key.
Assigning Watering Days for Program A
Turn the rotary dial to DAY OF WEEK in program A. The display will show an A and the cursor will blink under the days of week Monday, Tuesday, Wednesday, etc. [See Figure 6].

Using Manual Operation

Turn the rotary dial to AUTO.
The manual operation mode allows you to set durations in any of the stations from 1 to 99 minutes. Press the MANUAL key. Then press NEXT three times. The display will show a blinking cursor on station 1 along with - - MINS [See Figure 12].
FIGURE 12: LCD Display with Manual Operation
Manual and Semi-Automatic Modes
The Timer gives you a number of manual and semi-automatic modes for flexibility in watering. You can override the Timers automatic programming in a variety of ways.
FIGURE 6: LCD Display with Watering Days
To set the number of minutes for watering duration, press and Press ENTER to activate watering on Monday. An arrow appears under M and the cursor will advance to Tuesday (T), press ENTER to activate watering on this day. Repeat these steps for all days of the week. To skip a day, press NEXT. To delete a previously entered day, press CLEAR If you want to water every second day, press the NEXT key to advance the cursor to 2nd, then press ENTER. Note: If you choose to water every 2nd day, you cannot set specific days of the week for watering

Getting Started

Programming the Timer can be accomplished in just a few basic steps. Before you begin programming, it is important to install the batteries, set the time of day and date, and establish a watering plan.

hold the + key to advance to desired number of watering minutes. Use the - key to go in reverse. Press ENTER to begin watering. To skip a station, press NEXT until the cursor is blinking over the station number you wish to program. Example: To set station 3 for five minutes, press the MANUAL key; then press the NEXT key five times to select the manual operation mode and advance to watering for station 3; using the + or - key, set the manual watering duration to five minutes; then press ENTER [See Figure 13].

Install the Batteries

The Timer requires two AA batteries to maintain the time, date, and programs in case of AC power loss. In a typical installation, fully charged batteries should provide sufficient power for approximately three years of operation. Remove the terminal cover. Insert two AA batteries into the battery compartment. Return the terminal cover to its closed position.
Assigning Watering Intervals for Program B
Program B is used to water at specific intervals between days (1 to 28), or on odd or even calender dates. The Timer has a leap-year compensator and will ensure conformance to the odd and even schedule through the year 2100.
Turn the rotary dial to WATERING INTERVAL. The cursor will blink to the left of the word INTERVAL [See Figure 7].
FIGURE 13: Manual Watering Station 3 for Five Minutes

Page 2

Each valve has two wires. One wire is to be connected as the common. The common wires for all the valves can be connected together to one common wire going to the timer. The other valve wire is to be connected to the specific station wire that will control that valve [See Figure 17]. All wires should be joined together using wire nuts, solder, and/or vinyl tape. For additional protection to waterproof connections, a WaterMaster grease cap can be used. To avoid electrical hazards, only one valve should be connected to each station. The rated output is 24 volts AC at less than 0.240 Amps. Do not use solenoids that exceed these values.
Before returning this timer to the store, contact Orbit Technical Service at: 1-800-488-6156.

Listings

The timer is tested to UL-1951 (Indoor models) and is ETL listed. Appropriate international models are CETL and CE approved.
2. Connecting Valve Wires to the Timer
Note: After the MANUAL key has been pushed, if a selection is not made within 60 seconds the display returns to the time of day. To halt or discontinue semi-automatic or manual watering, press the CLEAR key once. The Timer will revert to your original automatic watering plan.

Trademark Notice

WaterMaster is registered trademark of Orbit Irrigation Products, Inc. The information in this manual is primarily intended for the user who will establish a watering schedule and enter that schedule into the timer. This product is intended to be used as an automatic timer for activating 24 VAC irrigation valves, as described in this manual.

Using the User Selectable Rain Delay Mode
With the rotary dial set to AUTO, press the RAIN DELAY key once then press ENTER. The Timer will force a 24-hour interruption of all scheduled watering. After 24 hours, the Timer will automatically return to its initial watering schedule. To increase the rain delay to 48 or 72 hours simply press the RAIN DELAY key again until the desired delay time is displayed, then press ENTER. To cancel the rain delay mode, press CLEAR [See Figure 14].
To stop automatic watering for 24, 48, or 72 hours, use the RAIN DELAY mode key.
Remove the terminal compartment cover. Strip 1/4" (6 mm) of the plastic insulation off the end of each wire. Determine which valve you want to connect to which station. Connect each valve wire to its station terminal (labeled 1-6) by inserting the bare wire fully into the terminal. It may be necessary to open the terminal to allow for wire insertion or removal. To do this, turn the screw with a Phillips screwdriver until wire is secure [See Figure 18]. Connect the common wire to the terminal labeled COM [See Figure 18].

COM PUMP 24V 24V

WaterMaster by Orbit Limited Four Year Warranty
Orbit Irrigation Products Inc. warrants to its customers that its WaterMaster products will be free from defects in materials and workmanship for a period of four years from the date of purchase. We will replace, free of charge, the defective part or parts found to be defective under normal use and service for a period of up to four years after purchase (proof of purchase required). We reserve the right to inspect the defective part prior to replacement. Orbit Irrigation Products Inc. will not be responsible for consequential or incidental cost or damage caused by the product failure. Orbit liability under this warranty is limited solely to the replacement or repair of defective parts. To exercise your warranty, return the unit to your dealer with a copy of the sales receipt.

To Station Valve

Note: While in rain delay mode, the timer will display the remaining hours (counting down) to the end of the accepted delay alternating with the current time and date. No other key besides CLEAR is accepted while the Timer is in the rain delay mode.
FIGURE 14: LCD Display with Rain Delay
FIGURE 18: Connecting Valve Wires
Note: Only one wire can be installed into each terminal. If more than two common wires are used in your system, splice several together so only one wire runs into the COM terminal. Protect the splice connection with a wire nut.

Australian Rating Information

Transformer:

Output: Input: 600 mA 240 VAC 24 VAC 24 VAC 50 Hz 50 Hz

Controller Ouput:

Complete System Shut Down
To shut the system down, turn the rotary dial to the OFF position. The Timer remains programmed but will not water.
Orbit Irrigation Products Inc. North Salt Lake, Utah 84054

57114-14 Rev F

OTHER QUALITY PRODUCTS AND ACCESSORIES
Installation of Indoor Mount Timer

Install the

controller in 4 easy steps 1. Choosing a Timer Location 2. Mounting the Timer 3. Connecting the Transformer 4. Connecting Valve Wires to Timer

Automatic Rain Shut-Off

The rain shut-off easily connects to the timer and prevents overwatering during rainy periods.

WaterMaster

8-Zone

CAUTION: INDOOR USE ONLY

CLASS 2 TRANSFORMER INPUT 120V AC 60Hz 35W OUTPUT 24V AC 1.2 AMP MODEL NO. DV. 24124
Weather Resistant Timer Box
Allows outdoor installation of most brands of indoor mount timers. UL listed.
1. Choosing a Timer Location
Select a location near a standard electrical outlet. Avoid using an outlet controlled by an ON/OFF switch. The timer should not be exposed to the weather or operate at temperatures below 14 degrees or above 113 degrees Fahrenheit (-10 to 45 degrees Celsius). Avoid direct sunlight. For use under normal pollution conditions. Installation works best in a garage or protected area. The timer should not be mounted outdoors.

Automatic Valves

Durable, non-corrosive plastic construction. Automatic valves are available in anti-siphon or straight valves with safe, low voltage.

2. Mounting the Timer

Automatic Converters
Durable non-corrosive plastic construction. Converts most brands of plastic or brass valves to automatic.
Screw a No. 8 screw at eye level leaving the screw head extended out from the wall about 1/8 inch. Use expanding anchors in plaster or masonry if necessary. Slip the keyhole slot in the back of the timer over the extended screw. Screw a No. 8 screw through each of the two holes at the bottom of the box into the wall [See Figure 15].

Grease Caps

Protects low voltage wires from corrsion or shorts.
Remote Control Timer Link
6 STATION TRANSMITTER MODEL #57036

Stations

ALL OFF

30 min

6 STATION RECEIVER

MODEL #57013

10 min

60 min

Remote Control Transmitter and Receiver
Control your sprinklers with the touch of a button up to 200' (60 m) from your sprinkler controller.

Keyhole

No. 8 Screw

Screw holes

FIGURE 15: Mounting of an Indoor Timer
3. Connecting the Transformer
With the wiring terminal shroud off, find the two terminal holes labeled 24 VAC. Make sure the transformer is not plugged in. Insert one of the two power leads from the transformer into each terminal. It doesnt matter which lead goes into which terminal. It may be necessary to open the terminal to allow for wire insertion or
removal. To do this, turn the screw with a Phillips screwdriver until wire is secure [See Figure 16]. Plug in the transformer Warning: Do not link two or more controllers together with one transformer. Slide the shroud back on.

TROUBLESHOOTING

Possible Causes of Problems
One or more stations do not turn on:
1. Faulty solenoid. 2. Wire broken or not connected. 3. Flow control stem screwed down, shutting valve off. 4. Programming is incorrect.
Stations turn on when they are not supposed to:
1. Water pressure is too high. 2. More than one start time is programmed.
One station is stuck on and will not shut off:
FIGURE 16: Connecting Transformer
Precautions: This controller is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the controller.
1. Faulty valve. 2. Particles of dirt or debris stuck in valve. 3. Valve diaphragm faulty.
All stations do not turn on:
1. Transformer defective or not connected. 2. Programming is incorrect. 3. Fuse has been blown.
Controller will not power up:
Installing Valves, Pump Start Relays & Master Valves
1. Fuse has been blown. 2. Transformer not plugged into an operational AC outlet.
Stations continue to turn on and off when they are not programmed to:
1. More than one start time is programmed with overlapping schedules. 2. Excessive pressure.
1. Wiring the Electric Valves
If the distance between the controller and valves is under 700 feet (210 m), use WaterMaster sprinkler wire or 20 gauge (AWG) plastic jacketed thermostat wire to connect the controller to the valves. If the distance is over 700 feet (210 m), use 16 gauge (AWG) wire. Terminals accept up to 14 gauge wire. The wire can be buried in the ground; however, for more protection wires can be pulled through conduit and buried underground. Be careful to avoid burying the wires in locations where they could be damaged by digging or trenching in the future.

Jacket Specific Zone Wire Wire Connectors in Grease Caps Common Wires Solenoids

Fuse blows repeatedly:

1. Short in wiring or solenoids.

Valves

FIGURE 17: Connecting Timer Wires to Valves

doc1

Introduction

Installation
Timer Location 1. Select a location that is near a standard electrical outlet. If this is not possible, a 16 gauge electrical cord can be used to add length between the timer and the transformer (up to several hundred feet). Avoid using an outlet controlled by an On/Off switch. 2. The timer should not be exposed to water or operated at temperatures below 14 degrees or above 113 degrees Fahrenheit. (-10 c + 45 c) Mounting the Timer 1. Screw a No. 8 screw at eye level leaving the screw head extended out from the wall about 1/8 inch. Use expanding anchors in plaster or masonry if necessary. 2. Slip the keyhole in the back of the timer over the extended screw. 3. Screw a No. 8 screw through each of the two holes at the bottom of the timer box into the wall. (See Figure 1.)

Keyhole

Sprinkler Timer

INSTRUCTIONS

M T W Th F S Su 2nd S T 1 A 2 R 3 T ZONE MANUAL MAN. CLEAR DURATION NEXT OFF SET WATERING DAYS AUTO 3rd EVERY RESET SET START TIMES SET WATER DURATION SET DAY/ CLOCK
Thank you for purchasing a quality WaterMaster timer. You will enjoy many years of satisfactory service, especially if proper installation and care is observed. Please read the manual completely before installation, programming and operation. For ease of use, the manual is in step by step sequence of installing, setup and operation. The WaterMaster timer keeps your yard beautiful whether you are at home or away. WaterMaster gives you convenience and flexibility, letting you use an automatic watering program or override the automatic program for special watering needs. The WaterMaster timer divides your property into four or six stations with watering durations from 1 minute to 99 minutes each. You can water your yard up to 3 times every day. Each start time will operate all stations in sequence. You may use one of two watering schedules. One schedule will water on specific days of the week. The other will water by periods - every other day or every 3rd day. The WaterMaster timer includes a manual override feature that allows you to water all stations sequentially, or to manually water one station at a time. Note: Illustrations in this booklet show only 4 station terminals & 4 stations on the display. 6 station products are fitted with 6 station terminals & show 6 stations on the display. Note: Always check local plumbing and electrical codes for requirements when installing the timer, transformer, and sprinkling system. Use only with household current with an appropriate transformer matching your voltage and plug type.
Help Before returning this timer to the store, contact OrbitTechnical Service at: 1-800-488-6156. Listings The timer is tested to UL-1951 standard and is ETL listed. Appropriate international models are CETL and CE approved. Trademark Notice WaterMaster is a registered trademark of Orbit Irrigation Products, Inc.

No. 8 Screw

Screwholes

MODEL NUMBERS*

57114, 57116 57414, 57416

*WT2 VERSIONS

Installation and Operating Instructions
For WaterMaster 4 and 6 Zone Timers
Wiring the Electric Valves Figure 1 1. If the distance between the timer and valves is under 700 feet, use WaterMaster Jacket Specific zone wire sprinkler wire or 20 gauge plastic jacketed thermostat wire to connect the timer and the valves. If the distance is over 700 feet, use 16 gauge wire. The wire can be buried in the ground; however, for more protecCommon Wires Solenoids tion, wires can be pulled through PVC pipe and buried underground. Be careful to avoid burying the wires in locations where they could be disturbed by digging Valves or trenching in the future. Figure 2 2. Each valve has two wires. One wire is to be connected as the common. All of the common wires for all the valves can be connected together to one common wire going to the timer. The other valve wire is to be connected to the specific station wire that is to control that valve. (See Figure 2.) 3. All wires should be joined together using wire nuts, solder, or vinyl tape. For additional protection to waterproof connections, a WaterMaster grease cap can be used. 4. To avoid electrical hazards, only one valve should be connected to each station. 5. The rated output is 24 volts AC at less than 0.240 Amps. Do not use solenoids that exceed these values.

Connecting Valve Wires to the Timer 1. Remove cover by sliding it down. 2. Determine which valve you want to connect to which station. Connect each valve wire to its station terminal (labeled 1-6) by inserting the bare wire. 3. Connect the common wire to the terminal screw labeled COM. (See Figure 3.) Installing Batteries For Program Back-Up 1. Install 2 AA (1.5 volt) alkaline batteries in the battery compartment. (See Figure 4.)

Programming

Step 1Setting Clock Time and Day of Week 1. Turn dial to SET DAY / CLOCK position. 2. Press and release RESET button using a pen or pencil. Display briefly shows all functions then 12:00 PM with blinking day of week indicator. 3. Press NEXT to advance the blinking Figure 6 indicator to the current day of week. (See Figure 6.) 4. Press ENTER to record current day of week. Indicator stops blinking and time begins blinking. (See Figure 7.) 5. Press the + or button to set the current Figure 7 time of day. For faster setting press and hold + or button. Press ENTER to record current time of day.
M T W Th F S Su 2nd 3rd S T 1 A 2 R 3 T PM ZONE MAN. DURATION M T W Th F S T 1 A 2 R 3 T ZONE MAN.
Step 3Setting Watering Durations for Each Station

N.A. N.A. N.A

EVERY SET DAY/ CLOCK
You can assign each station an automatic watering period as short as 1 minute and as long as 99 minutes. 1. Turn dial to SET WATER DURATION. Display shows minutes blinking and station indicator on Station 1. 2. Press + or button to select desired duration for the station. Figure 9 For faster setting press and hold + or button. 3. Press ENTER. Station indicator steps to Station 2. Display shows blinking . (See Figure 9.) 4. Repeat steps 2 and 3 for stations 2 through 6 as applicable. 5. Press CLEAR to erase a station duration.
M T W Th F S Su 2nd 3rd EVERY S T 1 A 2 R 3 T MINS ZONE MAN. DURATION

To zone valve

Figure 3

2 AA batteries

SET WATER DURATION

S Su 2nd 3rd

CAUTION: Do not allow the battery to contact the terminal strip.

N.A. N.A. N.A. 24V 24V

DURATION

Figure 4

2. With weak or no batteries, the program can malfunction or be erased with power failure. If this happens, disconnect the transformer, install fully charged batteries, plug in the transformer, and reprogram the timer.
Connecting the Transformer 1. With the cover off, find the two terminal holes labeled 24V. Make sure the transformer is not plugged in. Insert one of the two power leads from the transformer into each terminal hole and turn the screw with a Phillips screwdriver until wire is secure. Do not overtighten! 2. Plug in transformer. (See Figure 5.)

Step 2Setting Watering Cycle Start Times
Step 4Setting Watering Days
Note: A cycle start time is the time of day that the timer begins watering the first station, and all other programmed stations will then follow in sequence. There are not separate start times for each station. If you enter more than one cycle start time, all stations programmed to operate will water again (in sequence). 1. Turn dial to SET START TIMES. Display shows Start Time 1 in the left corner and -: blinking. 2. Press + or button to select the first cycle start time. For faster setting press and hold + or button. Figure 8 3. Press ENTER to record first start time. (See Figure 8.) 4. Press NEXT and repeat steps 2 and 3 if additional start times are required. 5. Press CLEAR to erase a start time. 6. The WaterMaster Timer allows up to 3 start times per day. Do not set overlapping start times. One start time will activate each station in sequence. You cannot set a cycle start time for each station. Generally only one cycle start time is required.
M T W Th F S Su 2nd 3rd EVERY S T 1 A 2 R 3 T 1 AM ZONE MAN. DURATION SET START TIMES
You decide which days of the week you want to water. You may choose to water every day, every second day, every third day, or any combination of days of the week. 1. Turn dial to SET WATERING DAYS. 2. Press NEXT to move indicator to the day you wish to water. 3. Press ENTER to record the day. Figure 10 (See Figure 10.) The indicator will remain solid on the days assigned to watering. The indicator will advance to the next day automatically and blink after you press ENTER. To skip to the next day press NEXT. 4. Repeat steps 2 and 3 for other days as desired. 5. Press CLEAR to make the highlighted day a non-watering day.
S T 1 A 2 R 3 T ZONE MAN. DURATION M T W Th F S Su 2nd 3rd EVERY

SET WATERING DAYS

Transformer

Figure 5

WARNING: Do not link two or more timers together using a common transformer. 3. Slide the cover back on until it snaps.
Step 5 Setting Periodic Watering Schedule

Manual Operation

The WaterMaster Timer provides 2 separate manual settings. These manual settings will not alter the automatic setting during or after use.

All Stations Cycle Once

Reviewing / Changing Settings
To Change Time and Current Day
Instead of selecting a particular day (or days) of the week, you may choose to water every second day or every third day. Note: If you have selected days of the week in step 4 you cannot select every 2nd or 3rd day watering also. 1. Turn dial to SET WATERING DAYS. 2. Press CLEAR until blinking indicator is pointing to either 2nd or 3rd day as desired. This clears any settings on week days. 3. Press ENTER. Indicator stops blinking. (See Figure 11.) The blinking indicator steps to the other selection.
S T 1 A 2 R 3 T ZONE M T W Th F S Su 2nd 3rd EVERY
1. Follow programming instruction in Programming section Step 1.

To Review Start Times

SET WATERING DAYS MAN. DURATION

Figure 11

1. Turn dial to AUTO. Press MANUAL. Display M T W Th F S Su 2nd 3rd shows ALL, solid over stations with proS T 1 grammed durations, and over MANUAL. A 2 ALL MINS R 3 (Ssee Figure 13.) T ZONE MAN. DURATION 2. Press ENTER. The timer will automatically water all assigned stations in sequence for Figure 13 the time assigned to each (a water droplet drawing will appear on the display) and then shut off and return to the automatic mode.

One Station Watering

1. 2. 3. 4.
Turn dial to SET START TIMES. The first start time will be displayed. Press NEXT to review remaining start times, if applicable. To make changes, press + or for any Start Time and follow instructions in Step 2 of Programming.
To Review Watering Durations
Step 6 Completing Automatic Operation
1. Turn dial to AUTO. Display shows current time and day. (See Figure 12.) Colon is blinking.
TIMER IS NOW PROGRAMMED AND WILL OPERATE AUTOMATICALLY.

Figure 12

1. Turn dial to AUTO. Press MANUAL. M T W Th F S Su 2nd 3rd 2. Press NEXT until indicator is on the station to S T 1 A 2 be watered. (See Figure 14.) R MINS 3 T 3. Press the + or keys for the desired waterZONE MAN. DURATION ing durationup to 99 minutes. 4. Press ENTER. A water droplet drawing will Figure 14 appear on the display. Timer will water for the desired duration and return to the automatic mode.
Turn dial to SET WATER DURATION. Station 1 duration will be displayed. Press NEXT to review other station durations. To make changes, press + or for any station duration and follow instructions in Step 3 of Programming.

To Review Watering Days:

1. Turn dial to SET WATERING DAYS. Display will show current settings. 2. To make changes, press CLEAR on any day or schedule (to skip to the next day press NEXT.) Follow instructions in Step 4 and/or Step 5 of Programming. Note: When watering begins, the display will show a water droplet and will count down the programmed time on the display.

To discontinue watering in the manual mode, press CLEAR. Timer will return to automatic mode. Note: After MANUAL has been pushed, if ENTER is not pushed within 10 seconds, the display will return to Time of Day.

Other Features / Default

Stop the Automatic Watering for 24 hours 1. Turn the dial to AUTO. 2. Press CLEAR. This will stop watering for 24 hours. An X appears on the display to indicate that watering has been temporarily stopped or inhibited. The number of hours remaining in the 24 hour period will appear on the display and will count down to 1 hour. 3. To cancel the inhibit mode with the dial in the AUTO position, press ENTER. The X disappears and automatic watering resumes. PROBLEM

Troubleshooting

POSSIBLE CAUSES
PROBLEM One or more valves do not turn on: 1. Faulty solenoid. 2. Wire broken or not connected. 3. Flow control stem screwed down, shutting valve off. 4. Programming is incorrect. Continuous loss of program: 1. Battery is not hooked up. 2. Battery is too weak to keep the program in timer. Stations turn on when they are not supposed to: 1. Water pressure is too high. 2. More than one start time is programmed. One station is stuck on and will not shut off: 1. Faulty valve. 2. Particles of dirt or debris stuck in valve. 3. Valve diaphragm faulty. All valves do not turn on: 1. Transformer defective or not connected. 2. Programming is incorrect. 3. Fuse blown. Timer will not power up: 1. Fuse needs replacing. Valves continue to turn on and off when they are not programmed to: 1. More than one start time is programmed with overlapping schedules. 2. Excessive pressure. Fuse blows repeatedly: 1. Short in wiring or solenoids. 2. Solenoid rating too high (max 24 VAC 240mA).
No Display/Function: 1. Check that batteries are fresh and transformer is connected. 2. Press RESET and reprogram. Display locked up: 1. Check that batteries are fresh. 2. Press RESET and reprogram. Waters each station 10 mins at 5 am: 1. In default mode. 2. Press RESET and reprogram.
Note: This feature will work even during watering, but you must press CLEAR twice.
System Shut Down Turn dial to OFF position. Timer remains programmed but will not water. For automatic rain shut-off, contact your WaterMaster dealer to purchase a WaterMaster Model 57091 automatic rain shut-off switch.
Note: The rain shut-off easily connects to existing timer and prevents sprinklers from watering during excessive rainfall.

System Reset Using a pen and pencil, press and release RESET button to erase all programming. Fuse The 0.5 amp slow-blow fuse provides circuit protection. For replacement use WaterMaster fuses, Radio Shack Part #270-1061, or equivalent. Easy Access to Batteries Two AA alkaline batteries. Caution In areas where heavy electrical equipment or lightning strikes are prevalent, an EMI Filter is recommended. (Radio Shack #61-2791 or equivalent). Default Program In the event of a power failure and you have no batteries or your batteries are dead, the timer will revert to the default program when power resumes. The clock reverts back to 12:00 p.m. and each station will be watered for 10 minutes when the clock shows 5:00 a.m. every day until reprogrammed.
M T W Th F S T 1 A 2 R 3 T S Su 2nd 3rd EVERY
Questions: Please call toll-free 1-800-488-6156 or visit us on the world wide web at www.orbitonline.com
WaterMaster Limited 2 Year Warranty Orbit Irrigation Products, Inc. warrants to its customers that its WaterMaster products will be free from defects in materials and workmanship for a period of two years from date of purchase. We will replace, free of charge, the defective part or parts found to be defective under normal use and service for a period of up to two years after purchase, proof of purchase required. We reserve the right to inspect the defective part prior to replacement. Orbit Irrigation Products, Inc. will not be responsible for consequential or incidental cost or damage caused by the product failure. Orbit Irrigation Products, Inc. liability under this warranty is limited solely to the replacement or repair of defective parts.

ZONE 3 4

To exercise your warranty, return the unit to your dealer with a copy of the sales receipt.

Figure 15

If watering begins in the default mode, the display shows as illustrated. (See Figure 15.)
Orbit Irrigation Products Inc. 845 North Overland Rd. North Salt Lake, Utah 84054

Printed in Hong Kong

ENGLISH

57114-14 Rev B 5/99

 

Tags

PSR7000 GR26sbtmr 1640Z Server 580 VT Samsung C101 Switch WD-1041WF EX-S12 CPC 6128 SX210 DPL580 GXT635 Besbi 125 V-MAX-2004 FM-2030 DDX7015 SL370 KD-510Z KX-TG1103CE DC199 ES8600 Atlinks 2410 SU-600 LC32AF1E SCS500 5 EMP-53 Sensation 9415 EWS12610W KC-850E RTI A3 Sportcity 125 46 MO 2 1 Contax G2 MP 180 Futaba 7C Gigaset CL1 Regenerator GZ-MG530 LE23T51B JBL J216 EWC1350 GE89MST ICD-SX55 Treadmills Yamaha GO46 SA-HE200 NEC VT58 DC410 AMP CAN 520DX Cosmicsoft 3 Breadmaker SX215 KX-TG7220FX MW83Y WD-16NEW RX-V595RDS PEG-NX80V XBM 838 Changer PS-42S5H Microverb 4 Gps-810EU KX-TG1311TR PX-300 LX3600D FX-570ES MS-7512 Motorola E2 VD-4220 TM 31 KD-G847 Dvdm-800 EOS 33 S80408KG B D HD6158 Seiko Y182 DSL-380T 26000 Pilots MJU-9000 Rockshox SID AH310 Micro Blackwhite Sharp VLZ3 KD-G352 Speaky Quantum 770 M KAC-PS501F W1941S-PF XM-SD61X DMR-ES35V SGH-T429 32PFL3403 12 UP-895MD

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101