Reviews & Opinions
Independent and trusted. Read before buy Orbit Watermaster 57161!

Orbit Watermaster 57161

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page 

Download (Spanish)
Orbit Watermaster 57161, size: 516 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Orbit Watermaster 57161About Orbit Watermaster 57161
Here you can find all about Orbit Watermaster 57161 like manual and other informations. For example: review.

Orbit Watermaster 57161 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Orbit Watermaster 57161 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Orbit Watermaster 57161 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

WTM230158 57114-14 rF_Eng.qxd

12/10/2002

1:50 PM

Page 1

Weak or missing batteries can cause the time and date to be erased after a power failure.
Installation Manual / Users Manual
Sprinkler Timers by Orbit
Set the Time of Day and Date
If this is the first time the Timer has been programmed, you should press the small recessed button labeled RESET. Pressing RESET does not affect the factory installed fail-safe program [See Figure 2].
FIGURE 7: LCD Display with Watering Interval
FIGURE 2: Programming Keys
Press and hold the + or - keys to select the number of days between watering. Example: If you want to water once every 10 days, set the interval at 10. To activate the watering interval, press ENTER. Note: If an interval of 3 is entered today, the Timer will water for the first time today, and then again every 3 days. To select odd or even day watering, press NEXT. The cursor will move to either the odd or even setting, then press ENTER. To erase a schedule, press CLEAR. To enter a new schedule, press NEXT.
Turn the rotary dial to the TIME/DATE position [See Figure 3]. 12:00 AM will appear in the display with three arrows pointing to the year, month, and day. Use the + and - keys to set the correct time of day. When the correct time of day is reached, press the ENTER key to lock in the time. To increase or decrease more rapidly, hold down either the + or keys until the display goes into rapid advance mode. A blinking cursor will appear below the arrow for the year, month, and date when programming [See Figure 3]. Use the + and keys to set the correct year, then press ENTER. Use the + and keys to set the correct month, then press ENTER. Use the + and keys to set the correct date, then press ENTER.
Reviewing and Changing Your Program
The Orbit Timer lets you easily review a complete watering plan. For example, to review Program-A watering start times, simply turn the rotary dial to the CYCLE START TIMES position in Program-A and check the times that have been entered. Using the NEXT key, you can advance through the schedule without fear of disturbing any programming. If you want to change the start times, watering days, or interval, simply follow the directions for that program. After reviewing or changing a watering schedule, remember to turn the rotary dial back to AUTO.
FIGURE 3: LCD Display with Surrounding Information
Ready for Automatic Operation
After programming is complete, turn the rotary dial to AUTO [See Figure 8]. The Timer is now fully programmed and ready to use in the automatic mode. In automatic mode, each program will operate sequentially, starting with Program-A.

MODELS

57114, 57161, 57162, 57242, 91046, 91054, 94122, 94124, 94126
Caution: If a watering schedule is not entered into the Timer, the factory installed fail-safe program will turn on each station every day for 10 minutes. To avoid accidental valve activation, either turn the rotary dial to OFF or enter a watering schedule.
Establish a Watering Schedule
To help you visualize how best to program the Timer, it might be helpful to make a watering plan on paper. This will help you establish which days and times you want to water.
FIGURE 8: Ready for Automatic Operation

version

section

Introduction

Programming
Thank you for selecting an Orbit sprinkler Timer. Orbit designers have combined the simplicity of mechanical switches with the accuracy of digital electronics to give you a Timer that is both easy to program and extremely versatile. The Orbit Timer provides convenience and flexibility, letting you run a fully automatic, semi-automatic, or a manual watering program for all your watering needs.
The Timer has two programs you can setup to control a variety of watering schedules. Depending on your needs, you can use either or both programs.
The Orbit Timer has the ability to override the automatic program without disturbing the preset program.
Semi-Automatic & Manual Operation
Enter Watering Schedule in Any Order
Using the Semi-Automatic Mode
(All stations cycle once both A & B programs) Turn the rotary dial to AUTO, then press the MANUAL key. The display will show AB, MANUAL, and ALL will be blinking [See Figure 9]. This indicates all stations will semi-automatically water for their assigned durations in sequence. To activate the assigned water durations in the A and B programs for each station, press ENTER.

FIGURE 9: Semi-Automatic Watering for Stations Assigned to A and B
Please read this manual completely before you begin to program and use the controller. A few of the most notable design features include:
You have the option of entering your watering schedule in whatever order you like. This feature makes it very easy to review and change your watering schedule. Your settings can be changed at any time while youre setting up the initial schedule or even after years of operation.

At-a-Glance Simplicity

By turning the rotary dial to one of nine settings you can review programming or easily make changes.
Start Times for Program A or B
Note: A start time is the time of day that the program begins watering the first station, and all other stations in the program will then follow in sequence. There are not separate start times for each station. Start times do not correspond to specific stations, but to programs (A or B). If you enter more than one start time, all stations in the specified program will water again (in sequence). The way you set the cycle start time is the same for both programs. Turn the rotary dial to the CYCLE START TIMES position in the program that you want to set. The display will show an A or B depending on which program you have selected. The display will show : and a blinking cursor in CYCLE START 1 location [See Figure 4]. Set the time you want to begin watering for start time 1 using the + or keys, then press the ENTER key. The display will advance to START 2. For additional start times, simply repeat this procedure by using the + and keys to enter the time and then press ENTER. Remember, Each start time will activate all stations that are set to water in the specified program. There are not separate start times for each station. Start times do not correspond to specific stations. Up to four start times can be entered per program (A or B).

Arm Chair Programmable

By inserting two AA alkaline batteries you can program the Timer prior to installing it in its permanent location.
The 0.75 amp slow-blow fuse provides circuit protection. For replacement, use WaterMaster 0.75 amp fuse or equivalent.

Programs

Lexan Language Covers
Available in English, French, Spanish, Italian, German.

1. Digital Display

A large LCD (Liquid Crystal Display) shows the time of day and indicates many of the programming settings. The display is completely interactive with all other controls.
Note: Water durations assigned to station 1 in program A will water first, then move to station 1 in program B before advancing to the second station and will continue alternating. Only those stations assigned a watering duration will water when using the manual or semi-automatic mode [See Figure 10].
FIGURE 10: Semi-Automatic Watering Entered for A and B Programs, All Stations

2. Programming Keys

The Timer has seven push button keys for setup and program entry. Working in conjunction with the rotary selector, the keys are used to set the time of day, watering time, watering days, start times, and other functions.
FIGURE 1: Location of Controls on the Timer

3. Selector Dial

This large dial makes it easy to see which function is currently selected and/or in which mode the Timer is set to operate.
FIGURE 4: LCD Display with Start Time

4. Reset Button

The reset button clears the time, date and user-defined programming but does not remove the factory installed fail-safe program. To prevent an accidental reset, the button is recessed into the panel and must be pressed with a small pointed object such as a pen or pencil tip.
Water Duration for Program A or B
Note: Both programs require watering durations to be programmed. Turn the rotary dial to ZONE DURATION position in either the A or B program. The display will show which program you have selected with an "A" or "B" and the - - cursor blinking at station "1" [See Figure 5].
(All stations cycle once, A program only) To activate stations assigned watering duration for the A program only, press the MANUAL key, followed by the NEXT key. This will activate stations with assigned watering durations in the A program only. To initiate this semi-automatic watering, press ENTER [See Figure 11]. (All stations cycle once, B program only)
Notable Programming Features
Two Watering ProgramsSummary
The Timer gives you the option of using one or both of the independent programs. Note that each station can independently be set to either A or B or both A and B programs.
To activate stations assigned watering durations for the B program only, press the MANUAL key, followed by pressing the NEXT key two distinct times. This will activate only those stations with assigned watering durations in the B program only. To initiate this semi-automatic watering, press ENTER.
FIGURE 11: Manual Watering in Either the A or B Program Only

ProgramA

This program lets you schedule selected stations to water on specific days of the week or to water every 2nd day. Program A repeats itself continuously in successive weeks.

FIGURE 5: Station Duration for Program A

ProgramB

Provides two options: One for odd or even day watering or for intervals ranging from everyday to every 28th day. This feature is designed to meet the growing needs and restrictions imposed by local governments and to conserve water. The Timer automatically calculates odd and even days (by date) for each month and makes adjustments for leap years to provide true odd and even watering through the year 2100.

Start-Time Stacking

The Timer has the intelligence to stack start times that overlap. If you enter two or more start times that overlap (in the same or in different programs), the Timer will not activate two stations at the same time. Instead, the Timer activates the first station and then activates the next station(s) in sequence after the first station finishes its preset watering duration. The Timer will NOT stack to the next calendar day. This prevents the Timer from violating an odd or even day watering schedule.
You can set the watering duration from 1 to 99 minutes. Press and hold the + key to advance the number of minutes, or use the - key to go in reverse, then press ENTER. When the minutes are set, A or B will appear over station 1 and the cursor will advance to station 2 and begin blinking. Simply repeat these steps to set watering durations for all zones on this program To skip a station, press the NEXT key. To erase previously programmed watering durations, press the CLEAR key.
Assigning Watering Days for Program A
Turn the rotary dial to DAY OF WEEK in program A. The display will show an A and the cursor will blink under the days of week Monday, Tuesday, Wednesday, etc. [See Figure 6].

Using Manual Operation

Turn the rotary dial to AUTO.
The manual operation mode allows you to set durations in any of the stations from 1 to 99 minutes. Press the MANUAL key. Then press NEXT three times. The display will show a blinking cursor on station 1 along with - - MINS [See Figure 12].
FIGURE 12: LCD Display with Manual Operation
Manual and Semi-Automatic Modes
The Timer gives you a number of manual and semi-automatic modes for flexibility in watering. You can override the Timers automatic programming in a variety of ways.
FIGURE 6: LCD Display with Watering Days
To set the number of minutes for watering duration, press and Press ENTER to activate watering on Monday. An arrow appears under M and the cursor will advance to Tuesday (T), press ENTER to activate watering on this day. Repeat these steps for all days of the week. To skip a day, press NEXT. To delete a previously entered day, press CLEAR If you want to water every second day, press the NEXT key to advance the cursor to 2nd, then press ENTER. Note: If you choose to water every 2nd day, you cannot set specific days of the week for watering

Getting Started

Programming the Timer can be accomplished in just a few basic steps. Before you begin programming, it is important to install the batteries, set the time of day and date, and establish a watering plan.
hold the + key to advance to desired number of watering minutes. Use the - key to go in reverse. Press ENTER to begin watering. To skip a station, press NEXT until the cursor is blinking over the station number you wish to program. Example: To set station 3 for five minutes, press the MANUAL key; then press the NEXT key five times to select the manual operation mode and advance to watering for station 3; using the + or - key, set the manual watering duration to five minutes; then press ENTER [See Figure 13].

Install the Batteries

The Timer requires two AA batteries to maintain the time, date, and programs in case of AC power loss. In a typical installation, fully charged batteries should provide sufficient power for approximately three years of operation. Remove the terminal cover. Insert two AA batteries into the battery compartment. Return the terminal cover to its closed position.
Assigning Watering Intervals for Program B
Program B is used to water at specific intervals between days (1 to 28), or on odd or even calender dates. The Timer has a leap-year compensator and will ensure conformance to the odd and even schedule through the year 2100.
Turn the rotary dial to WATERING INTERVAL. The cursor will blink to the left of the word INTERVAL [See Figure 7].
FIGURE 13: Manual Watering Station 3 for Five Minutes

Page 2

Each valve has two wires. One wire is to be connected as the common. The common wires for all the valves can be connected together to one common wire going to the timer. The other valve wire is to be connected to the specific station wire that will control that valve [See Figure 17]. All wires should be joined together using wire nuts, solder, and/or vinyl tape. For additional protection to waterproof connections, a WaterMaster grease cap can be used. To avoid electrical hazards, only one valve should be connected to each station. The rated output is 24 volts AC at less than 0.240 Amps. Do not use solenoids that exceed these values.

Before returning this timer to the store, contact Orbit Technical Service at: 1-800-488-6156.

Listings

The timer is tested to UL-1951 (Indoor models) and is ETL listed. Appropriate international models are CETL and CE approved.
2. Connecting Valve Wires to the Timer
Note: After the MANUAL key has been pushed, if a selection is not made within 60 seconds the display returns to the time of day. To halt or discontinue semi-automatic or manual watering, press the CLEAR key once. The Timer will revert to your original automatic watering plan.

Trademark Notice

WaterMaster is registered trademark of Orbit Irrigation Products, Inc. The information in this manual is primarily intended for the user who will establish a watering schedule and enter that schedule into the timer. This product is intended to be used as an automatic timer for activating 24 VAC irrigation valves, as described in this manual.
Using the User Selectable Rain Delay Mode
With the rotary dial set to AUTO, press the RAIN DELAY key once then press ENTER. The Timer will force a 24-hour interruption of all scheduled watering. After 24 hours, the Timer will automatically return to its initial watering schedule. To increase the rain delay to 48 or 72 hours simply press the RAIN DELAY key again until the desired delay time is displayed, then press ENTER. To cancel the rain delay mode, press CLEAR [See Figure 14].
To stop automatic watering for 24, 48, or 72 hours, use the RAIN DELAY mode key.
Remove the terminal compartment cover. Strip 1/4" (6 mm) of the plastic insulation off the end of each wire. Determine which valve you want to connect to which station. Connect each valve wire to its station terminal (labeled 1-6) by inserting the bare wire fully into the terminal. It may be necessary to open the terminal to allow for wire insertion or removal. To do this, turn the screw with a Phillips screwdriver until wire is secure [See Figure 18]. Connect the common wire to the terminal labeled COM [See Figure 18].

COM PUMP 24V 24V

WaterMaster by Orbit Limited Four Year Warranty
Orbit Irrigation Products Inc. warrants to its customers that its WaterMaster products will be free from defects in materials and workmanship for a period of four years from the date of purchase. We will replace, free of charge, the defective part or parts found to be defective under normal use and service for a period of up to four years after purchase (proof of purchase required). We reserve the right to inspect the defective part prior to replacement. Orbit Irrigation Products Inc. will not be responsible for consequential or incidental cost or damage caused by the product failure. Orbit liability under this warranty is limited solely to the replacement or repair of defective parts. To exercise your warranty, return the unit to your dealer with a copy of the sales receipt.

To Station Valve

Note: While in rain delay mode, the timer will display the remaining hours (counting down) to the end of the accepted delay alternating with the current time and date. No other key besides CLEAR is accepted while the Timer is in the rain delay mode.
FIGURE 14: LCD Display with Rain Delay
FIGURE 18: Connecting Valve Wires
Note: Only one wire can be installed into each terminal. If more than two common wires are used in your system, splice several together so only one wire runs into the COM terminal. Protect the splice connection with a wire nut.
Australian Rating Information

Transformer:

Output: Input: 600 mA 240 VAC 24 VAC 24 VAC 50 Hz 50 Hz

Controller Ouput:

Complete System Shut Down
To shut the system down, turn the rotary dial to the OFF position. The Timer remains programmed but will not water.
Orbit Irrigation Products Inc. North Salt Lake, Utah 84054

57114-14 Rev F

OTHER QUALITY PRODUCTS AND ACCESSORIES
Installation of Indoor Mount Timer

Install the

controller in 4 easy steps 1. Choosing a Timer Location 2. Mounting the Timer 3. Connecting the Transformer 4. Connecting Valve Wires to Timer

Automatic Rain Shut-Off

The rain shut-off easily connects to the timer and prevents overwatering during rainy periods.

WaterMaster

8-Zone

CAUTION: INDOOR USE ONLY

CLASS 2 TRANSFORMER INPUT 120V AC 60Hz 35W OUTPUT 24V AC 1.2 AMP MODEL NO. DV. 24124
Weather Resistant Timer Box
Allows outdoor installation of most brands of indoor mount timers. UL listed.
1. Choosing a Timer Location

Select a location near a standard electrical outlet. Avoid using an outlet controlled by an ON/OFF switch. The timer should not be exposed to the weather or operate at temperatures below 14 degrees or above 113 degrees Fahrenheit (-10 to 45 degrees Celsius). Avoid direct sunlight. For use under normal pollution conditions. Installation works best in a garage or protected area. The timer should not be mounted outdoors.

Automatic Valves

Durable, non-corrosive plastic construction. Automatic valves are available in anti-siphon or straight valves with safe, low voltage.

2. Mounting the Timer

Automatic Converters
Durable non-corrosive plastic construction. Converts most brands of plastic or brass valves to automatic.
Screw a No. 8 screw at eye level leaving the screw head extended out from the wall about 1/8 inch. Use expanding anchors in plaster or masonry if necessary. Slip the keyhole slot in the back of the timer over the extended screw. Screw a No. 8 screw through each of the two holes at the bottom of the box into the wall [See Figure 15].

Grease Caps

Protects low voltage wires from corrsion or shorts.
Remote Control Timer Link
6 STATION TRANSMITTER MODEL #57036

Stations

ALL OFF

30 min

6 STATION RECEIVER

MODEL #57013

10 min

60 min

Remote Control Transmitter and Receiver
Control your sprinklers with the touch of a button up to 200' (60 m) from your sprinkler controller.

Keyhole

No. 8 Screw

Screw holes

FIGURE 15: Mounting of an Indoor Timer
3. Connecting the Transformer
With the wiring terminal shroud off, find the two terminal holes labeled 24 VAC. Make sure the transformer is not plugged in. Insert one of the two power leads from the transformer into each terminal. It doesnt matter which lead goes into which terminal. It may be necessary to open the terminal to allow for wire insertion or
removal. To do this, turn the screw with a Phillips screwdriver until wire is secure [See Figure 16]. Plug in the transformer Warning: Do not link two or more controllers together with one transformer. Slide the shroud back on.

TROUBLESHOOTING

Possible Causes of Problems
One or more stations do not turn on:
1. Faulty solenoid. 2. Wire broken or not connected. 3. Flow control stem screwed down, shutting valve off. 4. Programming is incorrect.
Stations turn on when they are not supposed to:
1. Water pressure is too high. 2. More than one start time is programmed.
One station is stuck on and will not shut off:
FIGURE 16: Connecting Transformer

Precautions: This controller is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the controller.
1. Faulty valve. 2. Particles of dirt or debris stuck in valve. 3. Valve diaphragm faulty.
All stations do not turn on:
1. Transformer defective or not connected. 2. Programming is incorrect. 3. Fuse has been blown.
Controller will not power up:
Installing Valves, Pump Start Relays & Master Valves
1. Fuse has been blown. 2. Transformer not plugged into an operational AC outlet.
Stations continue to turn on and off when they are not programmed to:
1. More than one start time is programmed with overlapping schedules. 2. Excessive pressure.
1. Wiring the Electric Valves
If the distance between the controller and valves is under 700 feet (210 m), use WaterMaster sprinkler wire or 20 gauge (AWG) plastic jacketed thermostat wire to connect the controller to the valves. If the distance is over 700 feet (210 m), use 16 gauge (AWG) wire. Terminals accept up to 14 gauge wire. The wire can be buried in the ground; however, for more protection wires can be pulled through conduit and buried underground. Be careful to avoid burying the wires in locations where they could be damaged by digging or trenching in the future.
Jacket Specific Zone Wire Wire Connectors in Grease Caps Common Wires Solenoids

Fuse blows repeatedly:

1. Short in wiring or solenoids.

Valves

FIGURE 17: Connecting Timer Wires to Valves

doc1

INSTALLATION INSTRUCTIONS
ELECTRIC VALVE TROUBLE SHOOTING
Your Orbit Automatic Converter valve should provide years of trouble-free service. However, if you do have any problems, try the following solutions. PROBLEM: THE VALVE WILL NOT OPEN ELECTRICALLY First, run the valve manually: Open the bleed lever (rotating it clockwise) and check to see that the flow control is in the open position (Turn counter-clockwise). If the flow control is open and the valve still will not operate electrically, check the following possibilities. (Close bleed lever when manual test is completed) Check if.
1. Wiring is correct. 2. There is debris in the port hole. 3. Solenoid plunger is stuck. 4. Defective solenoid.

AUTOMATIC CONVERTER

MODEL 57029, 57030
1. REMOVE MANUAL STEMShut off the water supply and remove the manual valve stem, leaving the valve body installed. Remove the o-ring or flat washer. 2. INSERT CONVERTER AND REASSEMBLE VALVEAttach the automatic converter, making sure the o-ring or gasket seals completely. When converting a brass anti-siphon valve, the anti-siphon cover must be removed and replaced simultaneously with the converter. Make sure the plunger and gasket are lined up correctly when replacing the anti-siphon cover. Turn on the water supply and check assembly for leaks. 3. RUN THE WIREWith the power off, connect the valve to an Orbit timer (or other timer that uses a UL approved 24-volt class 2 transformer as a power source). Use a multi-colored, multi-strand, jacketed sprinkler wire. Be sure the wire has at least one more strand than the number of valves in the manifold. Trench and run the wire to the valves. It is recommended, in areas that you will be frequently digging, that you use a section of PVC as a protective covering.

Solution:

Check the wiring at the valve and at the timer. Check to see that the timer is working properly. Turn off the water. Remove the solenoid. Push a wire or large paper clip down through the round port hole working it up and down to free any debris. Be sure the plunger and o-ring are in place when reassembling. Turn off the water. Remove solenoid and clean out any sand and debris. Be sure the plunger and o-ring are in place when reassembling. Turn off the water. Unscrew the solenoid and replace with one from a working valve. If the valve now works, replace the solenoid. Be sure the plunger and o-ring are in place when reassembling.
4. ATTACH THE WIREAttach a colored wire to one wire on the solenoid and a common wire to the other wire of the solenoid. It doesnt matter which solenoid wire you use as the common. Attach the colored wires to the corresponding zone terminal in the timer and the common wire to the common connection of the timer. Use standard sprinkler wire (20 gauge) for distances less than 800 feet and 18 gauge wire for over 800 feet. Use an Orbit Grease Cap and Wire Nut at each solenoid for a water-proof connection. Also water-proof any splices made along the run. 5. CLOSE THE SPRINKLER VALVESTurn the Manual Bleed Lever clockwise until closed. Turn the water supply on. The valve should remain closed. 6. OPEN VALVES AND SET FLOW CONTROLTurn the Manual Bleed Lever counter-clockwise to manually open the valve. Open the flow control to adjust the sprinkler heads to the desired spray coverage. Then close the Manual Bleed Lever, the valve will shut off in a few moments. The system is now ready to be controlled electrically from the controller or manually by opening the Manual Bleed Lever. NOTE: The flow control is not a positive shut-off. DRAININGIn freezing areas, the valves and lines will need to be drained. Refer to the Orbit Layout Guide or your local dealer to recommend proper drain points. To insure the electric valves are completely drained in the fall, turn off the main sprinkler shut-off valve and electrically run each valve dry for a few minutes. Turn the timer to the off position until spring. CAUTION: If Static Water Pressure exceeds 80 PSI, a pressure regulator should be used. For outdoor use with cold water only: Do not use for indoor applications. Valves should be placed so that water drains away from the house. NOTES: Where possible, always protect valves with an Orbit Valve Box and place gravel in the bottom.

PROBLEM: THE VALVE WILL NOT CLOSE Check if.
1. Improper sizing. 2. Solenoid plunger is stuck. 3. Worn seat in valve body. 4. Debris between washer and valve seat. 5. Diaphragm is ruptured.
Check that the proper-sized automatic valve was purchased for your size and brand name of valve body. See conversion chart on reverse side. Turn off the water. Remove solenoid and clean out sand and debris. Be sure the plunger and o-ring are in place when reassembling. Turn off water. Remove the automatic converter and check that the lower seat of the valve body is not worn or damaged. Turn off water. Remove the Automatic Converter Valve by turning the hex nut counterclockwise. Clean out any debris. Turn off water. Replace Diaphragm Assembly.
PROBLEM: EXTERNAL VALVE LEAKS Check if.
1. Pressure is too high. 2. Leaking around screws. 3. Leaking below solenoid. 4. Adapter o-ring missing. 5. Hex Nut o-ring missing. 6. The diaphragm is split or torn.
Install a pressure regulator valve and set at about 80 PSI. Turn off the water. Undo the leaking screw 4 or 5 turns and retighten firmly. Turn off the water. Tighten the solenoid. Turn off the water. If using the Adapter Ring, check that the o-ring is in place. Turn off the water. Check that the Hex Nut o-ring or gasket is in place and is not pinched or otherwise unable to seal against the valve body. Turn off the water. Remove cap and change the diaphragm. Turn off the water. Check that the Automatic Converter Hex Nut has been installed into the valve body correctly. Attempt to reinstall the Automatic Converter into the valve body. If the threads are stripped, replace the Hex Nut.
INSTRUCTIONS FOR OPERATION
The Automatic Converter converts manual sprinkler valves to automatic. The Converter works with most 24-volt timers. Always check local codes before installing any sprinkler system. If static water pressure exceeds 80 PSI, a pressure regulator should be used.
ORBIT IRRIGATION PRODUCTS, INC. NORTH SALT LAKE, UTAH 84054
Orbit Irrigation Products, Inc. North Salt Lake, UT 84054 USA www.orbitonline.com | 1-801-299-5555
2007 Orbit Irrigation Products, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed.

PN 57029-32 Rev A

7. Hex Nut is cross threaded.

OTHER ORBIT PRODUCTS

PRODUCT

Automatic Rain Shut-Off

MANUAL VALVE
REPLACING THE MANUAL STEM WITH THE CONVERTER
Flow Control Manual Bleed Gasket or o-ring Anti-Siphon Cover

PARTS LISTING

Flow control Handle Solenoid Assembly 57041 Bleed Lever Solenoid Plunger Solenoid o-ring Cover Assembly S.S. Screws Spring Diaphragm Assembly

PART NUMBER

BENEFIT/DESCRIPTION OF USE
Automatically interrupts the watering cycle of sprinkler timer when it rains and returns the timer to automatic cycle when the water in the collecting pan evaporates. Allows outdoor installation of any brand of indoor mount timer. It is UL listed. Automatically activates pump for automatic watering (i.e. with well water).
Manual Valve Stem Anti-Siphon Cover
Weather Resistant Box UL Pump Start Relay

57095 57009

Flat Washer Valve Body
Cover Flat Washer Adapter Ring: Use when converting some plastic manual valves. Plunger
AUTOMATIC RAIN SHUT-OFF - 57069

PUMP START RELAY - 57009

Valve Body
WIRING THE CONVERTER TO THE TIMER
Valve Common Connection Single Common Wire Out (to timer) Grease Caps and Station Wire Connections
Body Assembly Hex Nut Sub-Assembly Seal Retainer Sub-Assembly Electrical requirements are 18 Volts A.C. minimum at the solenoid. Inrush volt-amps @24 V.A.C.= 5.5 VA Inrush current @24 V.A.C.=.35 AMPS Holding current @24 V.A.C.=.23 AMPS

To Timer

WEATHER RESISTANT BOX UL - 57095
Model 57030 includes a ring adapter required to convert most brands of manual valves to automatic.
Auto Converter brand compatibility table

3/4" Plastic

1" Plastic

3/4" Brass

57029 -

1" Brass

57030 PN 57029-32 REV B
ORBIT LIMITED 6 YEAR WARRANTY
Orbit Irrigation Products, Inc. warrants to its customers that its Orbit products will be free from defects in materials and workmanship for a period of six years from the date of purchase. We will replace, free of charge, the defective part or parts found to be defective under normal use and service for a period of up to six years after purchase: proof of purchase is required. We reserve the right to inspect the defective part prior to replacement. Orbit Irrigation Products, Inc. will not be responsible for consequential or incidental cost or damage caused by the product failure. Orbit Irrigation Products, Inc. liability under this warranty is limited solely to the replacement or repair of defective parts.

Champion Rainjet

Rainbird Richdel/Lawn Genie

proof no:

dimensions: flat: w: 11" h: 11.4" finished: w 5.7" h 3.67" d: 0" colors
Registration FOLD non printing PMS ???? color non printing PMS ???? PMS ????
Printers are responsible for meeting print production requirements. Any changes must be approved by the client and Fluid Studio. Printed piece must meet designated specifications on this form.
date: 05.13.07 des: RA spck: RA job no: 07WTM004005 client: ORBIT sku: 57029 p 9820 f 5815 www.fluid-studio.net 1065 South 500 West Bountiful, Utah 84010 upc: NA file name:

07WTM004005 57029-32 rB.indd

additional instructions:

software: InDesign CS2

 

Tags

C3800 250 SMS EWI4000S ICF-C773 2033 CV Nikon F70 Dell 1700 96888 213 PTZ Lide70 Aspire EL LQ-100 DES-1250G KX-P3626 V 2 Iwde 7145 Tahoe 2003 USR8000 5075E DVD-909 DVD-P375 LE15S51B ICF-C212 RC5215P Software H3600 CP-X960 LP-8600FX 42LG7000 BEU DR4810 PB2140 Hamachi 2 F88020VI P42W46X 30272 BM450 KX-TG1062 VLT4105 PM-300 EFP6411X SR-S583DW Junior 700 Kawai CA5 RM200B Prestige 650 A7V600-F LC-90MK2 B7620 CP3500 SF-345TP BDP-CX7000ES 1500G Backtrack 7045 KEY Picanto Hdcsd60 Pocket PC KX-TGA270S Platinum PRO-scratch 2 Azur 550A Attack-4 Edge 705 512SC UN40C7000 Grand Prix Finepix HS10 VP-D31I Clicksmart 420 Coche T4X BC-137 GX-50 WSP5010 SB-W500 CT-S280 ZS-M37 Digital Pets Review Lrbc20512WW AVM P2 R-315EX M402SR 94160TA HD NP-X20 US-144 N342I KDC-PSW9531 Rapid Polaroid I634 2 1 Crdh145-36 Portege 3440 MF3240 81919 GR-DVL320u-gr-dvl320 LE46C650 M200D 1 0 GHD8015F2 White Zoom H4N

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101