Radio-Controlled Projection Clock with Indoor Temperature
(Model #: RM988P / RM988PU) User Manual
Safety and care... 7 Warnings... 7 Additional resources... 8 Troubleshooting... 8 Specifications... 8

TABLE OF CONTENTS

About this guide... 2 Product overview... 2 Getting started.. 4 Batteries.. 4 AC power adapter... 4 Change settings... 4 Clock.... 5 Alarm.... 5 Temperature.. 6 Backlight... 6 Projector.... 6 Reset system... 7

ABOUT THIS GUIDE

Congratulations on your selection of the Oregon Scientific Radio-Controlled Projection Clock with Indoor Temperature (RM988P / RM988PU). This powerful device bundles time keeping, alarm, projection, and indoor temperature measurement features. Keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know. In this box, you will find: Main unit Batteries AC/DC power adapter TOP VIEW

PRODUCT OVERVIEW

DESCRIPTIONS 1. Snooze / Light button ( 6, 7) 2. Projection lens ( 7)

Product colors may vary.

FRONT VIEW

LCD DISPLAY

DESCRIPTIONS
1. Low battery icon ( 4) 2. RF Reception Signal ( 5) 3. Beep alarm (shows when ringing) ( 5) 4. Min / Max indoor temperature ( 6) 5. Time ( 5) 6. Alarm set time ( 5) 7. Alarm on / off (shows when on) ( 6) 8. Temperature ( 6)
BUTTON DESCRIPTIONS 1. LCD Display ( 3) 2. Alarm set / activate / deactivate alarm ( 5) 3. Mode switch modes ( 4) 4. Up / Down increase / decrease setting or activate / deactivate auto-synchronization ( 5)
5. Mem view minimum / maximum temperature measurements ( 6) 6. Projector ( 6) 3

EN BACK VIEW BATTERIES

GETTING STARTED
Batteries are supplied with this product. Replace them ) displays. The battery whenever the low battery signal ( cover is located on the back of the unit. Slide to open. Be sure to match the correct polarity, as shown in the battery compartment. After you change the batteries, press the RESET button with the point of a blunt object (such as a ball point pen). Do not use rechargeable batteries.
AC POWER ADAPTER An AC power adapter is supplied for use with this product. You must connect the power adapter if you wish to use the continuous projection feature. The jack is located on the bottom of the unit. If the AC power becomes unavailable, the unit will automatically switch to battery power.
DESCRIPTIONS 1. Projector focus knob ( 6) 2. Projector ( 6) 3. Image rotation knob ( 6) 4. 180 rotation (flip image) button (side) ( 6) 5. Projection on switch ( 7) 6. AC power adaptor jack (bottom 4) 7. Battery compartment ( 4) AC power adapter not shown. Reset button (located in battery compartment) not shown. 4

CHANGE SETTINGS

Press and hold MODE or ALARM for 2 seconds to enter UP or DOWN to change setting mode. Then, press each setting. Press and hold to enter fast-setting mode. Press MODE or ALARM to switch between settings.
This product can automatically synchronize the date and time with official time-keeping organizations in Frankfurt, Germany (RM988P) and Rugby, England (RM988PU). When the unit is within 1500 km (932 miles) of a RF signal, the reception icon will blink during reception. RECEPTION Reception takes minutes to complete. Once complete, the icon will stop blinking. Strong signal Weak signal No signal
SET OR CHANGE THE CLOCK Clock auto-synchronization must be deactivated before you manually set the clock. 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Select the date / month format, display language, weekday, UP or DOWN to change hour, and minute. Press the setting. Press MODE to confirm. The language options are (E) English, (D) German, (F) French, (I) Italian, and (S) Spanish. VIEW DAY OF WEEK OR SECONDS Press MODE.
For best results, place the unit away from metal or electrical objects, and near a window with a clear view to the sky. TO DISABLE OR ENABLE AUTO-SYNCHRONIZATION UP and DOWN for 2 seconds to disable Press and hold the auto-synchronization. The unit will not respond to radio signals until you reactivate the synchronization. To enable auto-reception, press and hold DOWN for 2 seconds. UP and 5

When activated, the Alarm starts quietly, then gradually becomes louder until it crescendos. It shuts off at one minute. The LCD display lights up for the first 8 seconds. SET ALARM 1. Press and hold ALARM for 2 seconds to enter setting mode. 2. Select the hour and minute. Press change the setting. 3. Press ALARM to confirm. UP or DOWN to
EN SNOOZE Press SNOOZE/LIGHT to temporarily disable the alarm for 8 minutes. The alarm icon will blink while Snooze is activated. TO TURN THE ALARM OFF OR ON Press ALARM, MODE, MEM, UP, or DOWN. To turn the alarm off completely (deactivate it for the next day), press ALARM until the icon disappears.

PROJECTOR

This product has a built-in projector for viewing the time. The maximum projection range is 2 meters (6 feet). The image gets larger the farther you display it.
PROJECT THE TIME In a darkened room, press SNOOZE/LIGHT to display the time for 5 seconds.

TEMPERATURE

This product measures current indoor temperature. MOVE IMAGE Adjust the projector arm. VIEW MIN / MAX / CURRENT MEASUREMENTS Press MEMORY. FLIP IMAGE Press the 180 Rotation button while the projector is on. CLEAR MIN / MAX MEASUREMENTS Press and hold MEMORY for 2 seconds until a beep sounds. ROTATE IMAGE The ROTATION knob is located on the back of the projector. Rotate to adjust.

BACKLIGHT

Press SNOOZE/LIGHT to illuminate the backlight for 5 seconds. 6 FOCUS IMAGE The FOCUS knob is located on the back of the projector. Rotate to adjust.
CONTINUOUS PROJECTION The AC power adapter must be plugged in to use this feature ( 4). Slide the PROJECTOR switch located on the back of the product to the ON position.

WARNINGS

This product is designed to give you years of service if handled properly. Observe the following guidelines: Never immerse the unit in water. This can cause electrical shock and damage the unit. Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. Do not tamper with the internal components. Do not mix new and old batteries or batteries of different types. Do not use rechargeable batteries with this product. Remove the batteries if storing this product for a long period of time. Do not scratch the LCD display. Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The contents of this user guide are subject to change without notice. Images not drawn to scale. Colors may vary.

RESET SYSTEM

The RESET button is located inside the battery compartment. Press it whenever you change the batteries, or whenever the product is not performing as expected (e.g., unable to establish radio frequency link with automatic clock). This will return all settings to default value, and you will lose any stored information (alarm and clock settings).

SAFETY AND CARE

Wash the unit with a slightly damp cloth and mild detergent. Avoid dropping the unit or placing it in a location where the AC power adapter will be stepped on.

ADDITIONAL RESOURCES

Visit our website (www.oregonscientific.com) to learn more about your new product and other Oregon Scientific products such as digital cameras, hand-held organizers, health and fitness gear, and weather stations. The website also includes contact information for our customer service department, in case you need to reach us. LxWxH Weight Temperature Unit

SPECIFICATIONS

Main unit dimensions 156 x 28 x 103 mm 248 g
C -5 C to 50 C (23 F to 122 F) 0.1 C (0.2 F)

TROUBLESHOOTING

Check here before contacting our customer service department. Problem Temp Calendar Clock Symptom Shows LLL or HHH Strange day of week Cannot auto-synch Remedy Temperature is out of range. Change language ( 5) Adjust batteries, press RESET ( 7), and manually activate auto-synch ( 5). If it still fails, you may be too far from a signal. Disable autosynching ( 5) 8
Range Resolution Radio-controlled clock Synchronization Clock display Hour format Calendar Alarm Snooze Power Main unit
Auto or disabled HH:MM:SS 12hr AM/PM (MSF format) 24hr (DCF format) DD/MM; weekday selection in 5 languages (E, D, F, I, S) Beep; 1 minute crescendo 8 minutes
2 x UM-3 (AA) 1.5V alkaline batteries AC/DC 4.5V power adapter (for continuous projector)

Cannot change clock

EC-DECLARATION OF CONFORMITY
This product complies with the essential requirements of Article 3 of the R&TTE 1999/5/EC Directives, if used for its intended use and that the following standard(s) has/have been applied: Efficient use of radio frequency spectrum (Article 3.2 of the R&TTE Directive) applied standard(s) Electromagnetic compatibility (Article 3.1.b of the R&TTE Directive) applied standard(s) ETS 300 683:1997 N/A
Additional information: The product is therefore conform with the Low Voltage Directive 73/23/EC, the EMC Directive 89/336/EC and R&TTE Directive 1999/5/EC (appendix II) and carries the respective CE marking. VS-Villingen / Germany August 2003 Gerhard Preis EC representative of manufacturer

COUNTRIES RTTE APPROVAL COMPLIED
Safety of information technology equipment (Article 3.1.a of the R&TTE directive) applied standard(s) EN 60950:1997
All EC Countries, Switzerland, CH and Norway N
2003. Oregon Scientific. All rights reserved

086-003025-02 9