Panasonic Broadcast Mechanical PARTS LIST
MODEL: AG-DVX100BP/BE/BAN, AG-DVX102BEN, AG-DVC180B

CONTENTS

FRAME & CASING PARTS ASSEMBLY (1)...MPL
FRAME & CASING PARTS ASSEMBLY (2)...MPL
HANDLE EVF PARTS ASSEMBLY....MPL
LCD PARTS ASSEMBLY.....MPL
PACKING PARTS ASSEMBLY....MPL
FRAME & CASING PARTS ASSEMBLY (1)

103 103

103 E22 101

103 E23

101 102

101 108

103 E20 E19

101 E3

101 101

109 E7

101 E6

109 103

FRAME & CASING PARTS ASSEMBLY(1)

Ref.No.

Part No.
VKM6819 VGH4856 VJF1470 VKW3295 VGU9194 VMG1460 VYQ3546 VYK1R55 VGQ6902 VGU9246 VML3710 VMP8588 VMP8198 VGQ8097 VMG1517 VWJ10G6033L0 VSC5793 VWJ1806 VGQ8096 VWJ20G6055L0 VGP6147 VMX0531 K4ZZ04000036 VYF2920 VGU9219 VHN0194 VMB3210 VGU8582 VJF1469 VYQ3547 VGU9197 VGL1012 VEE1A51 VMP7340 VWJ16G6033L0 VWJ1804 VWJ16G6090L0 VMG1715 VGU9209 VGU9199 VGQ8692 VWJ10G6050L0 VYK1R48 VGU9887 VMS7187 VMB3659 VGQ6901 VMB3996 VMP7331 VGQ8750 VGQ8751 VMT1633 VGQ8817 VSC5792 VGQ8753 VGQ8752 VGU9886 VMZ3612 VGU9894 VGH4857 VGQ8613 VWJ06G6033L0 VMB4000 VGU9893 VGU9222 VGQ6906 VGU9211 VGU9213 VGQ8612 VWJ12G6080L0 VWJ10G6050L0 VGU9217 VMG1418 VMG1520
Part Name & DescriptionPcs
CENTER FRAME U SIDE JACK NAME PLATE SIDE JACK CAP AWB WINDOW MIC SWITCHING KNOB SLIDE SW RUBBER COVER START/STOP U SIDE CASE R 1U MIC SWITCHING KNOB HOLDER ZOOM CLUCH KNOB CLUTCH SLIDE PLATE CLUTCH LEVER TRIPOD FRAME COOLING SHEET C3 LENS HEAT SINK SHEET (2) FLEXIBLE CABLE CF HEAT SINK FLEXIBLE CABLE COOLING SHEET C2 FLEXIBLE CABLE BACK CASE U CLUTCH SPACER BATTERY TERMINAL EVR COVER U CAMERA/VCR BUTTON SPACER BATTERY LOCK SPRING BATTERY LOCK BUTTON H.P CAP MODE DIAL U P.C.BOARD MONITOR LOCK KNOB MODE PANEL LIGHT DC CABLE DC IN ANGLE FLEXIBLE CABLE FLEXIBLE CABLE FLEXIBLE CABLE LCD CUSHION JOY STICK BUTTON MENU BUTTON VF CASE (R) FLEXIBLE CABLE TOP PANEL U VTR BUTTON2 LCD LOCK SHAFT MONITOR OPENER SPRING MONITOR KNOB POP UP SPRING OPENER HOLDER ANGLE COOLING SHEET C5 COOLING SHEET C6 FPC CUSHION COOLING SHEET R4 CAMERA HEAT SINK COOLING SHEET R3 COOLING SHEET R2 VTR BUTTON1 HINGE FPC HOLD SHEET SLIDE KNOB SLIDE KNOB SHEET ND FILTER HOLDER FLEXIBLE CABLE FOCUS KNOB SPRING CAMERA OP BUTTON ND SWITCHING KNOB HOLDER BLIND SHEET FOCUS BUTTON FOCUS SLIDE KNOB LCD HINGE COVER FLEXIBLE CABLE FLEXIBLE CABLE W.BAL KNOB (UPPER) RAIN COVER RUBBER (B) TOGGLE SW CUSHION 1 1

Remarks

VGQ8614 VGU9885 VGU9223 VGQ7175
CAM RIB CASE IRIS BUTTON W.BAL KNOB (LOWER) ND KNOB SHEET 1 2

DELETED

XQN2+B4FN XYN26+A6FJK XQN2+B4FJK XYN2+C5FJ XQN2+BJ4FJK XQN16+BJ4FJK XQN2+BJ6FJ XYN2+C3FJ XQN2+CJ6FJK
SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW

VYK1R53 DELETED DELETED

E2 E2 E3 E4 E5 E6 E7 E8 E12 E15 E16 E18 E19 E20 E21 E22 E23
VEP23638A VEP23638B VEP06G09A VEP06G11A VEP06G12A VEP06G13A VEP06G14A VEP06G10A VEP001K6A VEP04892A VEP06G07A VEP04893A VEP04895A VEP04894A VEP06G08A VEP01971A VEP01972A
CAMERA C.B.A. CAMERA C.B.A. R SIDE C.B.A. CAM OP1 C.B.A. CAM OP2 C.B.A. CAM OP3 C.B.A. CAM OP4 C.B.A. MENU C.B.A. BACK CONNECT C.B.A. REAR JACK C.B.A. POWER SW C.B.A. SIDE JACK C.B.A. MIC CH2 C.B.A. MIC CH1 C.B.A. MODE SW C.B.A. DC IN C.B.A. BATTERY C.B.A.
1 FOR AG-DVX100BP/AN 1 FOR AG-DVX100BE/EN/MC 1
FRAME & CASING PARTS ASSEMBLY (2)

including E102 103

32 101

108 29

108 34

106 106

VFB0215 VGP6148 VMS7653 VMP8331 VMP7325 VGH4860 VGQ8611 VGF1043 VXY1903Z1 VYQ3542 VXK1835 L2BB00000001 VSC5766 VKA0340 VGP6149 VXA8179 VXL3325 VMA0U09 VSC5765 VML3898 VHD1546 VGQ8545 VMP7605 VYK0Z96 VXW0742 VXW0743 VGQ8618 VMP8473 VGP6155 VGU9255 VMG1107 VMB3680 VEE1B96 VJF1468 VXQ1372 VXQ1373 VXW0741 L6DABBHC0001

GRIP BELT GRIP COVER CASSETTE COVER SHAFT BELT FIX ANGLE GRIP BELT ANGLE (FRONT) CASSETTE COVER WINDOW GARAGE COVER HOLDER GRIP SHEET MECHA U ZOOM SW U MECHA FRAME U DEW SENSOR POWER SHIELD (B) GRIP DUSTPROOF RUBBER GRIP FRAME LOCK U LINK ARM U LINK GUIDE POWER SHIELD (A) CLEANING ROLLER U SCREW LENS HOOD LENS HOOD WINDOW LENS CAP U CAMERA LENS U VXW0742/S CAMERA LENS U VXW0743/S BOTTOM COVER CASSETTE LOCK ANGLE SIDE TOP PANEL HOOD FIX PIECE MECH DUMPER RUBBER EJECT LOCK BUTTON SPRING AUDIO CABLE XLR CAP PRISM U VXQ1372/S PRISM U VXQ1373/S LENS U ZOOM MOTOR U 1 1
FOR AG-DVX100BP/AN FOR AG-DVX100BE/EN/

109 110

XQN2+B4FN XQN16+BJ6FJK XQN2+B4FJK VHD1133 XTB26+6GFJK XQN2+B4FJK XUC15FJ XQN2+BJ5FJK XQN14+B25FJ XQN16+CJ5FJ
SCREW SCREW SCREW SCREW SCREW SCREW E-RING SCREW SCREW SCREW

E1 E1 E13 E17

VEP03G82A VEP03G82B VEP001K7A VEP06G16A
VTR C.B.A. VTR C.B.A. TOP CONNECT C.B.A. ZOOM SW FLEX C.B.A.
1 FOR AG-DVX100BP/AN 1 FOR AG-DVX100BE/102BEN/180B 1 1
HANDLE EVF PARTS ASSEMBLY

E103 8

101 25

23 E10

VKH0425 VYF3062 VJF1421 VMC1697 VGQ6887 VGQ6888 VGU9207 VMG1479 VMP8479 VKC0594 VGQ6892 VYK1R58 VYQ3545 VYQ2773 VGQ6890 VMG1460 VGU9888 VYF3072 VYK1R40 VGQ6878 VMG1711 VMP8483 VYK0K76 VWJ1805 VWJ24G6070L0 VJF1158 VWJ1590 VXW0567 VYK1R66 VMG1286 VMZ3361
HANDLE REAR TALLY COVER U SHOE SPRING MIC CASE (LOWER) HANDLE FRONT COVER HANDLE S/S BUTTON HANDLE S/S BUTTON RUBBER HANDLE SW HOLD ANGLE VF HINGE EVF HINGE COVER EVF CASE U EVF LCD HOLDER U HELICOID ASS'Y EVF FILTER HOLDER SLIDE SW RUBBER COVER HANDLE SLIDE KNOB HANDLE COVER U MIC U MIC RUBBER FIX PIECE MIC RUBBER HOLDER MIC HOLDER ANGLE MIC CASE ASS'Y EVF FPC FLEX. CABLE CLAMPER INT MIC FLEX. EVF LENS ASS'Y EYE CAP U CUSHION RUBBER SUPPORT SHEET 1

111 112

XQN2+B4FN XQN2+BJ4FJK XQN2+B4FJK XQN2+BJ3FJK XQN2+CJ6FJK XQN2+BJ4FJ XQN2+B4FJK XSS2+4FJK XSN2+4FC XQN2+B4FN XQN2+BJ4FJK XQN2+BJ5FJK
SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW

E9 E10 E11

VEP06G15A VEP66499A VEP29166A
HANDLE C.B.A. F TALLY FLEX C.B.A. EVF CONNECT C.B.A.

LCD PARTS ASSEMBLY

VYK1R42 VYK1R60 VYK1R62 VGP6152 VGQ8616 VXD0465 VGQ8617 VMT1717 VMZ3610 VYK1R54 VYK1R63 VYK1R64 VMG1286
LCD U LCD U LCD U LCD CASE (BOTTOM) HINGE COVER (LOWER) HINGE HINGE COVER (TOP) WATERPROOF PAD LCD PCB INSULATION SHEET LCD CASE U LCD CASE U LCD CASE U CUSHION RUBBER 1
FOR AG-DVX100BP/AN/E FOR AG-DVX102BEN FOR AG-DVC180BMC

XQN16+B3FJK XQN16+B4FN

SCREW SCREW

VEP08346A

LCD LEV C.B.A.

PACKING PARTS ASSEMBLY

Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type.

(E,EN)

(E,EN,MC)
VPG1F32 VPG1F33 VPG1F34 VPG1F35 VPF1F36 VPN5826 VPN5825 VPF0884 VPN5930 VFA0459 VFC3891 VMG1458 VFC4136 VYC0890 VQT0U08 VQT0U09 VQT0U10 VQT0U11 VQT0U12 DE-852DE DE-811DE DE-811FE DE-811HE VPK0825 VYC0936 K2GJ2DZ00024 K2CB2CB00006 K2CT3DA00004 K2CA2DA00030 K2CP2DA00002 K2CR2DA00004 VFC3684 VPG0T56
PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE CUSHION (LOWER) CUSHION (UPPER) POLYETHYLENE BAG PARTITION PLATE WIRELESS REMOTE CONTROLLE SHOULDER BELT EYE CAP CAP STRAP MIC HOLDER ADAPTOR OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS AC ADAPTOR AC ADAPTOR AC ADAPTOR AC ADAPTOR ACCESSORY BOX MIC HOLDER U DC CABLE ASS'Y POWER CORD POWER CORD POWER CORD POWER CORD POWER CORD ACCESSORY 1U PACKING CASE (OUT) 1 FOR FOR FOR FOR FOR
AG-DVX100BP AG-DVX100BE AG-DVX102BEN AG-DVC180BMC AG-DVX100BAN
FOR FOR FOR FOR FOR FOR FOR FOR FOR
AG-DVX100BP AG-DVX100BE AG-DVC180BMC AG-DVX102BEN AG-DVX100BAN AG-DVX100BP AG-DVX100BE/102BEN AG-DVC180BMC AG-DVX100BAN
FOR FOR FOR FOR FOR FOR FOR
AG-DVX100BP AG-DVX100BE/102BEN AG-DVC180BMC AG-DVX100BAN AG-DVX100BE/102BEN AG-DVX100BE/EN/MC AG-DVC180BMC

MPL-10

Panasonic Broadcast
AG-DVX100B Menu Information

Using the setup menus

Use the setup menus to change the settings to suit the scenes you are shooting or what you are recording. You can also use the menu buttons on the remote control. (Page 19)
Press the OPERATION lever (h) (or move it y) to display the items.

Example:

OTHER FUNCTIONS

REMOTE DV CONTROL

OPERATION lever MENU button

DV CMD SEL

END SEARCH REC LAMP BEEP SOUND CLOCK SET TIME SHIFT
OFF REC_P BLANK OFF OFF OFF

PUSH MENU TO RETURN

When not shooting or recording, press the MENU button. The camera enters the menu mode and the following is displayed on the screen.

Camera mode

CAMERA MENU 1. SCENE FILE 6 7. CAMERA SETUP. SW MODE. AUTO SW. RECORDING SETUP. DISPLAY SETUP. OTHER FUNCTIONS
Move the OPERATION lever e or r to highlight the item you want to change.
VCR1 OFF REC_P BLANK OFF OFF

PUSH MENU TO EXIT

VCR mode
VCR FUNCTIONS 1. PLAYBACK FUNCTIONS 4 5. RECORDING SETUP. AV IN/OUT SETUP. DISPLAY SETUP. OTHER FUNCTIONS
Press the OPERATION lever (h) (or move it y), then move it e or r to select the setting you want to change. To change a setting, move [q], then move the OPERATION lever e or r. Example:
Initializing the menu settings
The setup menus are divided into user files and scene files. You can initialize these separately. To initialize the user file (all items except the scene files) In the OTHER FUNCTIONS screen, USER FILE, select INITIAL. The settings for the current user file are returned to the factory settings. (Page 78) To initialize the scene files From the 6 scene files, select the one you want to initialize with the scene dial. Then in the SCENE FILE screen, SAVE/INIT, select INITIAL. The settings for the selected scene file are returned to the factory settings. (Page 70) There is no effect on the other scene files.
VCR1 OFF REC_P BLANK OFF FRONT REAR BOTH
To change other settings, repeat steps 4 and 5. When you have finished, press the MENU button to return to the function screen. To change other settings, repeat steps 2 to 5. When the menu mode is finished, press the MENU button again and return to the normal screen.

Setup menu structure

Camera mode menu

CAMERA MENU SCENE FILE

(Pages 69 and 70)

CAMERA SETUP

(Page 71)
SYNCRO SCAN ASPECT CONV COLOR BAR SETUP MID GAIN HIGH GAIN ATW HANDLE ZOOM IRIS DIAL USER1 USER2 USER3

SW MODE

(Pages 71 and 72)

AUTO SW

(Page 72)

A.IRIS AGC ATW AF

DETAIL LEVEL V DETAIL LEVEL DETAIL CORING CHROMA LEVEL CHROMA PHASE COLOR TEMP MASTER PED A. IRIS LEVEL GAMMA KNEE MATRIX SKIN TONE DTL V DETAIL FREQ PROGRESSIVE NAME EDIT SAVE/INIT REC SPEED AUDIO REC MIC ALC MIC GAIN 1 MIC GAIN 2 TC MODE TCG FIRST REC TC TC PRESET UB MODE UB PRESET ONE-SHOT REC REC TIME

RECORDING SETUP

(Pages 74 and 75) (Page 76)
DISPLAY SETUP OTHER FUNCTIONS

(Pages 77 and 78)

REMOTE DV CONTROL DV CMD SEL END SEARCH REC LAMP BEEP SOUND CLOCK SET TIME SHIFT POWER SAVE LANGUAGE H.P MODE FILE TRANS USER FILE HOUR METER
ZEBRA DETECT 1 ZEBRA DETECT 2 MARKER VIDEO OUT OSD DATE/TIME LEVEL METER ZOOM FOCUS TAPE BATTERY OTHER DISPLAY LCD BACKLIGHT LCD SET EVF SET SELFSHOOT EVF MODE EVF COLOR DISPLAY ASPECT

VCR mode menu

VCR FUNCTIONS PLAYBACK FUNCTIONS

(Page 73)

32K (12bit) AUDIO AUDIO OUT

(Pages 74 and 75)

AV IN/OUT SETUP

(Page 75) (Page 76)

A. DUB INPUT DV OUT DATE/TIME LEVEL METER TAPE BATTERY OTHER DISPLAY VIDEO OUT OSD CAMERA DATA LCD BACKLIGHT LCD SET EVF SET EVF MODE EVF COLOR DISPLAY ASPECT

DISPLAY SETUP

REC SPEED AUDIO REC 1394 TC REGEN TC MODE TCG FIRST REC TC TC PRESET 1394 UB REGEN UB MODE UB PRESET DV IN PRESET REMOTE END SEARCH CLOCK SET TIME SHIFT LANGUAGE USER FILE FILE RECEIVE HOUR METER

Setup menu list

SCENE FILE screen
Item/ (Display mode) Description of settings Item/ Display mode) GAMMA (camera) Description of settings Selects gamma curve. LOW: Using the gamma curve, which the slope of low-brightness is modest, makes it staid image. The contrast become sharp. NORMAL: Makes standard images. HIGH: Using the gamma curve, which the slope of low-brightness is modest, spreads out the tone of dark parts and makes it bright image. The contrast become soft. B.PRESS: Makes the contrast sharper than LOW. CINELIKE: Uses the gamma curve to complete the cine-line image. Images have less noise than CINELIKE_D. CINELIKE_D: Dynamic range is higher than CINELIKE. CINELIKE_V: Uses the gamma curve to complete the cine-like image of the emphasis on contrast. When CINELIKE Gamma is selected, we recommend that the lens aperture is set to the lower level (about 1/2) than normal image level for making full use the characteristics. KNEE (camera) To avoid an over exposure, use this to set the compression level (knee point) of the high-intensity video signals which the CCD received. AUTO: Sets the level automatically according to the received signals. LOW: Low setting (compression begins from approximately 80%) MID: Medium setting (compression begins from approximately 90%) HIGH: High Setting (compression begins from approximately 100%) are the factory settings.
DETAIL LEVEL Adjusts the amount of detail. (camera) -7 - 0 - +7 V DETAIL LEVEL (camera) DETAIL CORING (camera) Adjusts the level of outline correction in vertical screen. -7 - 0 - +7 Adjusts the level of removing noises of the detail signal. -7 - 0 - +7 Set to - for a clearer image. Noise increases slightly. Set to + to decrease noise. Adjusts chroma level. -7 - 0 - +7 Finely adjusts chroma phase. -7 - 0 - +7 Finely adjusts color temperature (after adjusting white balance). -7 - 0 - +7 Adjusts the black master pedestal as the basis for images. -15 - 0 - +15 Sets AUTO IRIS level. -4 - 0 - +4
CHROMA LEVEL (camera) CHROMA PHASE (camera) COLOR TEMP (camera) MASTER PED (camera) A. IRIS LEVEL (camera)
Setup menu list (continued)
Item/ (Display mode) MATRIX (camera) Description of settings Chooses a MATRIX table, and sets the color for shooting. NORM: Makes colors suitable for a shooting in the open air or in using a halogen lamp as the source of light. ENRICHED: Makes colors brighter than the NORM1 mode. FLOU: Makes colors suitable for shooting indoors under fluorescent lights. CINE-LIKE: Makes colors suitable for movie-like shooting. Sets the skin tone details to ON or OFF. When ON is selected, skin tone details are reduced, which softens the skin tones. ON OFF Sets the vertical detail when shooting in progressive mode. THIN : Select this to thin the detail of images. MID : Select this to slightly thicken the detail of images. THICK : Select this to thicken the detail of images. When images were shot in the progressive mode in which the vertical detail is set as THIN or MID and are played on a monitoring television (60i interlace), you will feel flickers caused on horizontal lines and almost horizontal oblique lines. When you play images under the progressive mode, set the detail as THIN or MID. This gives you higher resolution images than setting the detail as THICK. Item/ (Display mode) Description of settings

PROGRESSIVE Sets the shooting in progressive mode. (camera) OFF: Select this to disable progressive mode. 30P: Select this to shoot in 30P mode (30 frames/second). 24P: Select this to shoot in 24P mode (24 frames/second). The tape is recorded in [2:3] conversion. 24P (ADV): Select this to shoot in 24P advanced mode (24 frames/second). The tape is recorded using advanced conversion. NAME EDIT (camera) SAVE/INIT (camera) Edits the name of the selected scene file you have selected with the scene file dial. SAVE: The changed settings in the scene file are saved. The original scene file settings will be restored when the menu mode is released, the operation is switched to the VCR mode or when the power is turned off if you do not select SAVE. INITIAL: The selected scene file settings in the SCENE FILE dial are returned to the factory settings.

SKIN TONE DTL (camera)

V DETAIL FREQ (camera)
are the factory settings.

CAMERA SETUP screen

Item/ (Display mode) Description of settings

SW MODE screen

Item/ (Display mode) MID GAIN (camera) Description of settings Sets the gain value which is to be allocated to the M position of GAIN switch. 0dB 3dB 6dB 9dB 12dB Sets the gain value which is to be allocated to the H position of GAIN switch. 0dB 3dB 6dB 9dB 12dB Sets the operation of the ATW (Auto Tracking White) function which is to be allocated to the WHITE BAL switch. OFF: Disables the ATW function. However, if the ATW function is set to the AUTO button or USER button, the operation of that button becomes effective. Ach: Activates the ATW function when the WHITE BAL switch is set to A. Bch: Activates the ATW function when the WHITE BAL switch is set to B. PRE: Activates the ATW function when the WHITE BAL switch is set to PRST. Sets the zoom speeds allocated to the setting positions of the HANDLE ZOOM switch. L/OFF/H: Sets LOW (speed) /OFF/HIGH (speed) to each position of 1/2/3 (zoom is disabled when set to OFF). L/M/H: Sets LOW/MID (medium speed)/ HIGH to each position of 1/2/3. Sets the rotation and the aperture control of the IRIS dial (when in MANUAL IRIS mode). DOWN OPEN: The iris opens when the IRIS dial is turned downward. UP OPEN: The iris opens when the IRIS dial is turned upward. are the factory settings. Menus
SYNCRO SCAN Adjusts the synchro scan shutter speed used for shooting images on a (camera) TV screen, etc. If you move and hold the OPERATION to e or r, changing speeds up and a beep sounds. PROGRESSIVE MODE OFF: 1/60.3 1/250.0 PROGRESSIVE MODE 30P: 1/30.1 1/48.0 1/250.0 PROGRESSIVE MODE 24P/24PA: 1/24.1 1/48.0 1/250.0 ASPECT CONV Selects the aspect ratio of the images which are to be recorded. (Page 34) (camera) NORMAL LETTER BOX SQUEEZE COLOR BAR (camera) Sets the color bar to ON or OFF. ON OFF Even if the color bar is set to ON, it reverts to OFF when the unit is switched to VCR mode or when the power is turned off. Adds the setup level (black level). 0%: The setup level is not added. 7.5%: A 7.5% setup level is added for recording.

HIGH GAIN (camera)

ATW (camera)

SETUP (camera)

HANDLE ZOOM (camera)

IRIS DIAL (camera)

Item/ (Display mode) USER1 (camera) Description of settings Enables a function to be allocated to the USER1 button. COLOR BAR: Color bar display (Page 35) SPOTLIGHT: Sets the auto iris control for the spotlight to ON or OFF. BACKLIGHT: Auto iris control for the backlight compensation (Page 35) BLACKFADE: Blackfade (Page 35) WHITEFADE: Whitefade (Page 35) MODECHECK: Press the button to check the status of the current camera setting displayed on the viewfinder and LCD monitor. ATW: Sets the ATW function to ON or OFF. ATWLOCK: Press the button to fix the value of white balance. Press again and the ATW function is activated. GAIN: 18 dB: Press the button to set the gain value to 18 dB. This function is disabled in progressive mode and slow shutter mode. When the gain value is set to 18 dB or set from 18 dB to another value, the image can be disordered for a moment. INDEX: INDEX recording (Page 35) SLOWSHUT: Slow shutter mode (Page 40) Enables a function to be allocated to the USER2 button. For further details, refer to USER1 above. BACKLIGHT Enables a function to be allocated to the USER3 button. For further details, refer to USER1 above. INDEX

AUTO SW screen

Item/ (Display mode) A.IRIS (camera) Description of settings ON: Performs auto iris control when in auto mode. The IRIS button is disabled. OFF: Disables the auto iris control when in auto mode. This performs the iris control selected with the IRIS button. Sets the Auto Gain Control function for when the A. IRIS option is set to ON. 6dB: Enables the Auto Gain Control function (max 6 dB) when the Auto Mode is selected. 12dB: Enables the Auto Gain Control function (max 12 dB) when the Auto Mode is selected. OFF: Disables the Auto Gain Control function when the Auto Mode is selected. ON: Enables the ATW (Auto Tracing White Balance) function when the Auto Mode is selected. You cant enable or disable the ATW function with the WHITE BAL switch or the USER button when this is selected. If ATWLOCK is assigned to the USER button, however, you can set the White Balance value with the USER button. OFF: Disables the ATW function when the Auto Mode is selected. The ATW function that has been selected with the WHITE BAL switch applies. ON: Performs auto focus when the auto mode is established. Neither FOCUS switch nor the PUSH AUTO button works. OFF: Performs no auto focus when the auto mode is established. The focusing is performed by the FOCUS switch or PUSH AUTO button.

AGC (camera)

USER2 (camera)

AF (camera)

USER3 (camera)
PLAYBACK FUNCTIONS screen

Item/ (Display mode) 32K (12bit) AUDIO (VCR) Description of settings Sets the sound to be output as CH1 and CH2 signals when playing back a tape that was recorded in the 32K (12bit) audio mode. ST1: Selects the sound that was recorded during shooting. CH1 signals = CH1 track CH2 signals = CH2 track ST2: Selects the sound that was dubbed on the recording. CH1 signals = CH3 track CH2 signals = CH4 track MIX: Mixes the sound that was recorded during shooting and the sound that was dubbed on the recording. CH1 signals = CH1 track + CH3 track CH2 signals = CH2 track + CH4 track Note When the sound is recorded in the 48K (16bit) audio mode, CH3 and CH4 do not exist so the following is always the case. CH1 signals = CH1 track CH2 signals = CH2 track Item/ (Display mode) AUDIO OUT (VCR) Description of settings Sets the audio signals to be output from the AUDIO IN/OUT pin jack when the tape is played back. CH1CH2: CH1 output = CH1 signals CH2 output = CH2 signals CH1: CH1 output = CH1 signals CCH2 output = CH1 signals CH2: CH1 output = CH2 signals CH2 output = CH2 signals
32K (12bit) AUDIO item/AUDIO OUT item settings and audio track signals output from the AUDIO IN/ OUT jack
Audio recording mode 32K (12bit) AUDIO item setting ST1 32K (12bit) AUDIO OUT item setting CH1CH2 CH1 CH2 CH1CH2 CH1 CH2 AUDIO IN/OUT jack CH1 output CH1 CH1 CH2 CH3 CH3 CH4 CH1+CH3 CH1 CH1 CH2 AUDIO IN/OUT jack CH2 output CH2 CH1 CH2 Menus CH4 CH3 CH4 CH2+CH4 CH2 CH1 CH2

ST2 MIX

CH1CH2 CH1 CH2

48K (16bit)

RECORDING SETUP screen
Item/ (Display mode) REC SPEED (camera) (VCR) AUDIO REC (camera) (VCR) MIC ALC (camera) Description of settings Set the recording-time mode. SP: SP (standard) mode LP: LP (long) mode Set the audio recording mode for conversion to PCM audio. 32K (12bit): 12bit/21kHz 48K (16bit): 16bit/48kHz Sets microphone level auto control to ON or OFF. ON OFF Set this ON to reduce distortion at high input levels. You should also adjust the input level with the AUDIO control whatever you set here. Sets the input level of the external microphone connected to the INPUT 1 terminal. -50dB -60dB Sets the input level of the external microphone connected to the INPUT 2 terminal. -50dB -60dB Selects the time code used when signals from equipment connected with the DV terminal is recorded. ON: Records with the time code signal input through the DV terminal. OFF: Records with the time code set at TC MODE/TCG/FIRST REC TC. This setting has priority over any setting you have made in TC MODE/ TCG/FIRST REC TC. If there is no input to the DV terminal, the setting follows the ones set at TC MODE/TCG/FIRST REC TC. Selects the correction mode of the internal time code generator. DF : Uses the drop frame mode. NDF : Uses the non-drop frame mode. The non-drop frame mode will be used when you are shooting in a progressive mode, 24P or 24P (ADV). Item/ (Display mode) TCG (camera) (VCR) Description of settings Use this to set the mode in which to advance the time code. FREE RUN: The time code advances regardless of the operation mode. REC RUN: The time code advances only when recording.

MIC GAIN 1 (camera)

MIC GAIN 2 (camera)

1394 TC REGEN (VCR)

FIRST REC TC Select the time code to be recorded when you start recording. (camera) (VCR) REGEN: Select to record the time code so that it continues from the time code already on the tape. PRESET: The time code does not continue from the time code on the tape. The value you set at TC PRESET is used as the initial value when recording the time code. The time code does continue on from the one on the tape, however, if you continue recording from something on the tape. TC PRESET (camera) (VCR) Sets the initial time code. This is effective when you have select PRESET in FIRST REC TC. Set the frame value to 0 or a multiple of 5 when you are shooting in a progressive mode, 24P or 24P (ADV). Using any other value will cause the time code to differ. Selects the user information used when signals from equipment connected with the DV terminal is recorded. ON: Records with the user information signal input through the DV terminal. OFF: Records the user information set with UB MODE. If you select ON here, this has priority over the settings in UB MODE. If the signal has no user information, the none is recorded. If there is no signal being input through the DV terminal, then the UB MODE settings are used. is the factory setting.

1394 UB REGEN (VCR)

TC MODE (camera) (VCR)
RECORDING SETUP screen (continued)
Item/ (Display mode) UB MODE (camera) (VCR) Description of settings Set the information you want for user information. USER: Records user information. TIME: Records the current time. DATE: Records the current date. TCG: Records the data from the time code generator. FRM. RATE: Records the frame conversion frame rate. Item/ (Display mode) UB PRESET (camera) (VCR) ONE-SHOT REC (camera) REC TIME (camera) Description of settings Set user information. Make sure you have set USER in UB MODE. Set ONE-SHOT recording mode. (Page 34) ON: OFF: Sets the length of time for ONE-SHOT recording. (Page 34) 0.5s: 0.5 seconds 1s: 1.0 second 1.5s: 1.5 seconds 2s: 2.0 seconds
DV IN PRESET Synchronizes the cameras TCG with the TC from DV input when you press (VCR) the TC SET button. ON: The mode is on. OFF: Cancels the mode.

a: Checking information for user information b: Frame sequence No. 0 to 4 are displayed during 24P/ 24P (ADV) mode. F is displayed during 60i/30P mode. c: Frame rates Frame rate (60/30/24) I/P ID Conversion data Frame rate coefficient d: Recording management data Frame updates REC START/STOP data

AV IN/OUT SETUP screen

Item/ (Display mode) A DUB INPUT (VCR) Description of settings Selects the sound to be recorded for audio dubbing. (Page 56) MIC: A_IN: Select ON to convert analog input signals into digital signals and output them from the DV connector. (Page 58) ON OFF are the factory settings. Menus

DV OUT (VCR)

DISPLAY SETUP screen
Item/ (Display mode) ZEBRA DETECT 1 (camera) ZEBRA DETECT 2 (camera) Description of settings Sets the brightness level of the leftleaning zebra patterns on the screen. 80%, 85%, 90%, 95%, 100%, 105% Sets the brightness level of the rightleaning zebra patterns on the screen. 80%, 85%, 90%, 95%, 100%, 105%, OFF Note The zebra patterns do not appear if you select OFF. Select ON to display the marker. ON OFF To display the marker, press the ZEBRA button. (Page 33) Select ON to output information displayed in the viewfinder and LCD monitor together with the signals from the VIDEO IN/OUT jack. ON OFF Sets whether to display the date and time on the screen and whether to output from the VIDEO IN/OUT jack. OFF: The date and time are not displayed. TIME: The time is displayed. DATE: The date is displayed. TIME&DATE: The time and date are displayed. If you select any setting other than OFF, the date and/or time are included in the image output signals regardless of the VIDEO OUT OSD setting. Item/ (Display mode) Description of settings
CAMERA DATA Select ON to show the camera settings (such as image stabilizer, F-number, (VCR) and gain value) during tape playback. OFF ON LCD BACKLIGHT (camera) (VCR) LCD SET (camera) (VCR) Adjusts the backlight of the LCD monitor. Select HIGH for a brighter backlight than usual. HI NORMAL Adjusts the display level of the images on the LCD monitor. (Page 25) LCD COLOR LEVEL: LCD BRIGHTNESS: LCD CONTRAST: Adjusts the display level of the images on the viewfinder. (Page 25) EVF COLOR LEVEL: EVF BRIGHTNESS: EVF CONTRAST: Select the LCD mirror mode for selfportrait shooting. Select MIRROR to reverse left and right during self-portrait shooting. NORMAL MIRROR Select when to show images on the viewfinder. ON: Images always appear on the viewfinder. AUTO: Images do not appear on the viewfinder when the LCD is open. Select color or black and white for the images on the viewfinder. ON: Color OFF: Black and white Select the aspect ratio of the LCD monitor and viewfinder. AUTO: Changes automatically to suit the recording or play mode. 4:3: Fixed at 4:3 16:9: Fixed at 16:9 There is a 10% overscan on the LCD when the setting is 16:9 (but not on the viewfinder). You will see the whole image on both the LCD and viewfinder when the setting is 4:3. are the factory settings.

MARKER (camera)

VIDEO OUT OSD (camera) (VCR) DATE/TIME (camera) (VCR)

EVF SET (camera) (VCR)

SELFSHOOT (camera)

EVF MODE (camera) (VCR)

LEVEL METER Select ON to display the audio level meter. (camera) (VCR) ON OFF ZOOM FOCUS (camera) TAPE BATTERY (camera) (VCR) OTHER DISPLAY (camera) (VCR) Select ON to display the zoom and focus values. ON OFF Select ON to display the remaining tape and battery charge. ON OFF Select how much information to display. (Page 65) OFF, PARTIAL, ALL
EVF COLOR (camera) (VCR) DISPLAY ASPECT (camera) (VCR)

OTHER FUNCTIONS screen

Item/ (Display mode) REMOTE (camera) (VCR) Description of settings Sets the operations of the supplied remote control unit. (For settings on the remote control (Page 20) VCR1: Accepts commands from a remote control set to VCR1. VCR2: Accepts commands from a remote control set to VCR2. OFF: Operations are not accepted from any remote control. Sets the control method for backup recording with a backup unit connected to the DV connector. OFF: The backup unit is not controlled. EXT: The backup unit can be controlled by the START/STOP button. The images shot by the video camera are stored in the backup unit. Note that the video camera does not record them. BOTH: The images shot by the video camera are recorded by both the video camera and backup unit. CHAIN: When the video cameras tape approaches its end during shooting, the backup unit set in the recording stand-by mode automatically starts to record the images. Sets how the START/STOP button works for the backup unit. REC_P: The button works as a REC/REC PAUSE button. STOP: The button works as a REC/REC STOP button. Note If the backup unit does not have a rec pause function, select STOP. Sets the operation to be performed when a blank search is conducted. (Page 51) BLANK: REC END: Item/ (Display mode) REC LAMP (camera) Description of settings Sets lighting of the tally lamp. OFF: Tally lamp does not light. FRONT: Front tally lamp (microphone side) lights. REAR: Rear tally lamp (viewfinder side) lights. BOTH: Both tally lamps light. Selects ON/OFF for the beeps. ON OFF Select ON to be warned by a beep in the following situations. When a beep sounds, the audio signals from the OUT jack are muted and the beep is output instead. One beep when you set the power switch to ON when you start shooting Two beeps when you pause shooting Three beeps when you have set the cassette tape write-protect when condensation has formed inside the camera-recorder when a problem has occurred in the camera-recorder Ten beeps when it is not possible to record to the tape CLOCK SET (camera) (VCR) TIME SHIFT (camera) (VCR) Sets the camera-recorders calendar. Menus

DV CONTROL (camera)

BEEP SOUND (camera)

DV CMD SEL (camera)

The time set using this item is added to the clock time of the internal calendar (time difference compensation) and displayed on the screen. The added time is also recorded on the tape. +23h - +1h, OFF, -1h - -23h (In 1-hour increments) are the factory settings.
END SEARCH (camera) (VCR)
Item/ (Display mode) POWER SAVE (camera) Description of settings Select the power saving mode. When you dont perform any specified operations for five minutes* ON: the camera recorder turns off automatically. OFF: the cylinder head pauses and goes into standby mode without cutting the power. *The camera recorder does not go into power save mode if you use the following controls. AUTO Button FOCUS switch PUSH AUTO button GAIN switch. WHITE BAL switch WHITE BAL switch IRIS button and dial CH1/CH2 SELECT switch INPUT1/2 switch AUDIO control OIS button SHUTTER button SPEED SEL button Zoom button and ring HANDLE ZOOM switch Opening or closing the LCD Select headphone output. TAPE: Sound recorded on the tape is output. LIVE: Current input is output. The beep sound is not output even if you have selected ON for BEEP SOUND. Use this when you are shooting in the 24P mode or any other time that sound delay becomes noticeable. LOAD: The previous scene file settings are loaded. SAVE: The changed user file settings are saved. INITIAL: The user file settings are returned to the factory settings. After LOAD or INITIAL, switch camera-recorder OFF and then back ON to ensure that the settings take effect. Item/ (Display mode) FILE TRANS (camera) Description of settings Make settings for scene file transfer. (Page 47) SCENE: Transfer the scene file currently selected with the SCENE dial. SCENE ALL: Transfer all scene files. USER: Transfer all user scene files. Note When in FILE TRANS mode, only the menu operation buttons will function. Makes the camera ready to receive scene files from another camera. (Page 47) Note RECEIVE MODE appears on the screen after you set this mode. When in FILE RECEIVE mode, only the menu operation buttons will function. Displays the total running time (a 5digit figure in 1-hour increments) of the cylinder head.

FILE RECEIVE (VCR)

HOUR METER (camera) (VCR)

HP MODE (camera)

USER FILE (camera) (VCR)