Panasonic Broadcast

AJ-HDX900 Menu Information
Chapter 7 Menu description tables

7-1 Menu configuration

MENU USER MENU MAIN MENU OPTION MENU OPTION
Items selected in <USER MENU SELECT>
SYSTEM SETTING PAINT RB GAIN CONTROL RGB BLACK CONTROL MATRIX COLOR CORRECTION LOW SETTING MID SETTING HIGH SETTING ADDITIONAL DTL SKIN TONE DTL KNEE/LEVEL GAMMA CAMERA SETTING
SYSTEM MODE REC FUNCTION OUTPUT SEL VIDEO OUT SETTING MONITOR OUT SETTING RC OUT SETTING DOWNCON SETTING GENLOCK OPTION MODE
VF OPERATION CAMERA ID SHUTTER SPEED SHUTTER SELECT USER SW SW MODE WHITE BALANCE MODE USER SW GAIN LENS IRIS
VF DISPLAY VF MARKER VF USER BOX VF INDICATOR1 VF INDICATOR2 MODE CHECK IND !LED

How to open the menus

USER MENU: Press MENU button to display. MAIN MENU: Hold down MENU button for 3 seconds or more to display. OPTION MENU: Press MENU button while holding down LIGHT button to display.
FILE MAINTENANCE SYSTEM CHECK DIAGNOSTIC LENS ADJ BLACK SHADING WHITE SHADING LENS FILE ADJ
CARD READ/WRITE CARD R/W SELECT LENS FILE LENS FILE CARD R/W SCENE INITIALIZE
VTR MENU USER MENU SELECT SYSTEM(USER) PAINT(USER) VF(USER) OPERATION(USER) FILE(USER) MAINTENANCE(USER) VTR(USER)
VTR FUNCTION BATTERY/TAPE BATTERY SETTING1 BATTERY SETTING2 MIC/AUDIO 1 MIC/AUDIO 2 TC/UB UMID SET/INFO VTR DIAG
<Notes> There is a total of 42 camera-related items on three pages (14 items per page) and 14 VTR-related items on one page which can be set. The items with the shading cannot be selected using <USER MENU SELECT>. The items with the underlining can be selected only using <USER MENU SELECT> on condition that all the items (equivalent to the number of items on one page) are selected together. Individual items cannot be selected.
How to interpret the menu lists
Item The following abbreviations indicate whether the menu changes are stored (written) in the corresponding data or loaded (read) from the data. The changes cannot be stored or loaded when / is indicated. S: The changes can be stored or loaded as scene file data. C: The changes can be stored or loaded using CARD READ/WRITE. U: The changes can be stored or loaded as user data. Refer to sections 7-6-4 SCENE and 7-6-5 INITIALIZE. F: The changes can be stored or loaded as READ FACTORY DATA. Refer to section 7-6-5 INITIALIZE. R: The changes can be stored or loaded using RC DATA SAVE. Refer to section 5-10 Connection of the remote control unit (AJRC10G). SYSTEM MODE
Variable range 1080-50i 1080-59.94i 720-50P 720-59.94P
Remarks For setting the system frequency and the recording format of the unit. When this item is switched, turn OFF the POWER switch on the unit and then turn it ON again.
This column indicates the variable range in which the item can be set and the choice of the settings which can be selected for the item.
Described in this column are the operations which can be expected to result when the items settings are selected.
Chapter 7 Menu description tables (continued)

7-2 SYSTEM SETTING

7-2-1 SYSTEM MODE
Item Item SYSTEM MODE For AJ-HDX900E For AJ-HDX900P Variable range 1080-50i 1080-59.94i 720-50P 720-59.94P Remarks For setting the system frequency and the recording format of the unit. When this item is switched, turn OFF the POWER switch on the unit and then turn it ON again. O When the remote control unit (AJ-RC10G) is connected, this item is not displayed. To switch this item, operate the main unit independently. For setting the video system for shooting. For 50 Hz REC TIME For 59.94 Hz Variable range 00s01f
Remarks For setting the recording time (one cut). When the CAMERA MODE item is set to 24P or 24PA, the value is set in increments of 5 frames.

59s29f For 50 Hz 00s01f

59s24f
PAUSE TIME For 59.94 Hz 00h00m00s01f
CAMERA MODE For AJ-HDX900E (1080-50i) 50i 25P (1080-59.94i) 60i 30P 24P 24PA (720-50P) 50P 25P (720-59.94P) 60P 30P 24P

00h04m59s29f

For setting the recording pause time. When the CAMERA MODE item is set to 24P or 24PA, the value is set in increments of 5 frames.
23h59m59s29f 00h00m00s01f

For AJ-HDX900P

00h04m59s24f

TAKE TOTAL TIME

23h59m59s24f NONE

TOTAL REC TIME 00m00s01f

For setting the time required for shooting. Select a setting from NONE (shooting continues until it is stopped manually) to 5DAY (5 days). For displaying the total recording time. The setting for this time cannot be changed. The total time yielded by adding the REC TIME, PAUSE TIME and TOTAL TAKE TIME is displayed. O This indication is just a guide for the recording time. It is impossible to record for a period longer than the recording time of the tape. For setting the availability of audio records during INTERVAL REC. For setting the time taken until recording is to start after the REC START button is pressed in the INTERVAL REC mode. For setting the PRE RECORDING function. OFF: Recording starts about 0.4 seconds after pressing the REC START button or the VTR button on the lens. ON: The PRE RECORDING function is activated. For details, refer to 3-4 To record video signals of a few seconds before starting recording (PRE-RECORDING function). For setting the length of time for which the video and audio signals can be recorded before the REC START button is pressed in PRE RECORDING. For setting the RETAKE function. ON: The RETAKE function is activated. OFF: The RETAKE function is not activated. It returns to OFF once the power is turned off. For details, refer to 3-6 To take the previous cut again (RETAKE function).

DETAIL For setting the detail function for the down converter output signals ON/OFF. The down converter output signals contain detailed components that are set during HD signal processing. In this setting, these signals overlap the detailed components dedicated to the down converter outputs. Even if this setting is turned off, it is impossible to turn off the detailed components set during HD signal processing. For setting the horizontal detail correction level for the down converter output signals.

GL PHASE HD SDI COMPOSIT

H.DTL LEVEL 00

V.DTL LEVEL

For setting the vertical detail correction level for the down converter output signals.

DTL CORING

H PHASE COARSE 100 For setting the noise elimination level of the details.

+100 H PHASE FINE 100

H.DTL FREQ. 1

2DLPF ON OFF

For selecting the horizontal frequencies. 1: 2.5 MHz 4: 4 MHz 2: 3 MHz 5: 4.5 MHz 3: 3.5 MHz

detail

For making fine adjustment for aligning phases of the horizontal synchronization, for executing the GENLOCK.
For setting the 2-D low path filter reducing cross colors. ON: Cross colors are reduced. OFF: Cross colors are not reduced.
SET UP For AJ-HDX900E For AJ-HDX900P 0% 7.5% For setting the setup level for the down converter output signals. <Note> When the system frequency is set to 50 Hz, the setup level will be 0%.

7-2-9 OPTION MODE

Item REC TALLY Variable range RED GREEN CHAR Remarks For selecting the method to access records on the unit when the unit is connected to peripheral devices and used remotely. RED: The red tally lamp lights. GREEN: The green tally lamp lights. CHAR: For displaying REC in the viewfinder. For selecting whether or not to hold the UMID GPS position information while the power is off and record the information as the data still held as the previous value until another measurement can be taken after the power is next turned on. HOLD: The data is held and recorded. CLEAR: The data is cleared at the same time as the power is turned off, and all zeros (no information) are recorded from the time the power is turned on until the measurement is next taken. For setting the transfer rate of signals output from the DVCPRO connector. S200: 200 Mbps S400: 400 Mbps For setting the input channel of signals input to the DVCPRO connector. 0 63: To fix to the designated value AUTO: To follow the settings of the externally connected devices For setting the input channel of signals output from the DVCPRO connector. 0 63: To fix to the designated value AUTO: To follow the settings of the externally connected devices For setting the control for recording start/stop operations of external devices that are connected to the DVCPRO connector. OFF: Do not control the externally connected devices. BOTH: To control both the unit and the externally connected devices For setting the control of recording stop operations of the external devices that are connected to the DVCPRO connector. REC_P: Operation to pause recording STOP: Stopping operation For setting metadata (UMID information) to output to the HD SDI signals. ON: To output OFF: Not to output For setting that the detection signals of the communication error is output to the HD SDI signals. ON: To output OFF: Not to output

S C U F R

B GAIN AWB PRE 200
For setting the Rch gain when the WHITE BAL switch is in the PRST position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.) For setting the Bch gain when the WHITE BAL switch is in the PRST position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.) For setting the Rch gain when the WHITE BAL switch is in the A position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.) For setting the Bch gain when the WHITE BAL switch is in the A position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.) For setting the Rch gain when the WHITE BAL switch is in the B position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.) For setting the Bch gain when the WHITE BAL switch is in the B position. O If the remote control unit is connected, settings made from the menu are disabled. (The set value is displayed.)

+200 100

R PEDESTAL +000

G PEDESTAL

+100 100

R GAIN AWB A 200

B PEDESTAL

B GAIN AWB A 200

PEDESTAL OFFSET

+100 ON OFF

R GAIN AWB B 200

R FLARE 100

B GAIN AWB B 200

AWB A GAIN OFFSET ON OFF

For setting the values of the Rch gain and the Bch gain when the auto white balance is executed as the WHITE BAL switch is in the A position. ON: To retain the values set in the items of R GAIN AWB A and B GAIN AWB A OFF: The values of the Rch gain and the Bch gain is set to 0. For setting the values of the Rch gain and the Bch gain when the auto white balance is executed as the WHITE BAL switch is in the B position. ON: To retain the values set in the items of R GAIN AWB B and B GAIN AWB B OFF: The values of the Rch gain and the Bch gain is set to 0. G FLARE 100

B FLARE 100

AWB B GAIN OFFSET ON OFF

7-3-3 MATRIX

Item MATRIX TABLE A B Variable range Remarks For selecting the color correction table for the linear matrix.

7-3-4 COLOR CORRECTION

Item R (SAT) Variable range 63
Remarks For performing correction of red. the color saturation

MATRIX R-G 63

For performing the linear matrix adjustment. (red/green)

R-Mg (SAT)

+63 63

MATRIX R-B

For performing the color saturation correction between red and magenta.
For performing the linear matrix adjustment. (red/blue)

Mg (SAT)

MATRIX G-R
For performing the correction of magenta.

saturation

For performing the linear matrix adjustment. (green/red)

Mg-B (SAT)

MATRIX G-B
For performing the color saturation correction between magenta and blue.
For performing the linear matrix adjustment. (green/blue)

B (SAT)

MATRIX B-R
For performing correction of blue.
For performing the linear matrix adjustment. (blue/red)

B-Cy (SAT)

MATRIX B-G
For performing the color saturation correction between blue and cyan.
For performing the linear matrix adjustment. (blue/green)

Cy (SAT)

L MATRIX TABLE
+63 OFF A B OFF A B OFF A B For selecting the color correction table when the GAIN switch is in the L position.
For performing the correction of cyan.

Cy-G (SAT)

M MATRIX TABLE
For performing the color saturation correction between cyan and green.
For selecting the color correction table when the GAIN switch is in the M position.

G (SAT)

H MATRIX TABLE
For selecting the color correction table when the GAIN switch is in the H position.
For performing the correction of green.

G-Yl (SAT)

<Note> Items with $ in front of their names are set by the PAINT MENU SW ($) R/W menu items on the <CARD R/W SELECT> screen. Items without $ in front of their names are set by the PAINT MENU LEVEL R/W menu item. For details, refer to 7-6-2 CARD R/W SELECT.
For performing the color saturation correction between green and yellow.

Yl (SAT)

For performing the correction of yellow.

Yl-R (SAT)

For performing the color saturation correction between yellow and red.

7-3-5 LOW SETTING

Item R (PHASE) Variable range 63
Remarks For performing the hue correction for red.

Item MASTER GAIN

Variable range 3dB
Remarks For setting the master gain to 3, 0, 3, 6, 9, 12, 15, 18, 21, 24, 27 or 30 dB.

R-Mg (PHASE)

For performing the hue correction between red and magenta. H.DTL LEVEL

30dB 00

For performing the correction level setting.

horizontal

Mg (PHASE)
For performing the hue correction for magenta. V.DTL LEVEL
For performing the vertical detail correction level setting.

Remarks For setting the center position on the I axis (for setting an area that enables skin tone.)

I WIDTH

255 000
SKIN TONE ZEBRA VF ON OFF
For setting the area width for enabling the skin tone on the I-axis of which the center is the I CENTER.

Q WIDTH

255 00
For setting the area width for enabling the skin tone on the Q-axis of which the center is the I CENTER

Q PHASE

90 180
SKIN TONE ZEBRA VOUT ON OFF
For setting phases of the area for enabling skin tone as setting the standard to the Qaxis.
SKIN TONE ZEBRA MONI ON OFF For the setting to superimpose the zebra pattern in the skin tone area output from the MON OUT connector. For selecting the skin tone table for enabling the skin tone details. For fetching the color information of A or B, which is selected in the SKIN TONE TABLE item, near the center marker. When this function is executed, data from I CENTER to Q PHASE are fetched automatically. The fetched data will be the table data of A or B, which is selected in the SKIN TONE TABLE item. It is impossible to obtain color information of both A and B at the same time. 0

SKIN TONE TABLE A B

SKIN TONE GET

Q-WIDTH I-WIDTH Y-MAX

SKIN DTL CORING
For setting the effect level of the skin tone detail.
For setting the maximum value of brightness for enabling the skin tone.

I-CENTER direction

+ direction

Q-PHASE

For setting the minimum value of brightness for enabling the skin tone. =SKIN TONE AREA

Y-MIN 0

7-3-10 KNEE/LEVEL
Item MASTER PED Variable range 200

7-3-11 GAMMA

Remarks Item MASTER GAMMA Variable range 0.30
Remarks For setting the master gamma in increments of 0.01 steps.
For performing the MASTER PEDESTAL setting.

MANUAL KNEE

+200 ON OFF For setting the mode which is to be established when the AUTO KNEE switch is at OFF. The KNEE POINT/SLOPE setting value is active when ON is selected. For setting the knee point position in increments of 0.5% steps.

0.75 15

R GAMMA
For performing the gamma setting for Rch.

KNEE POINT 70.0%

B GAMMA

+15 15

For performing the gamma setting for Bch.

KNEE SLOPE

107.0% 00

7-4-4 VF INDICATOR1

Item EXTENDER Variable range ON OFF ON OFF ON OFF ON OFF ON OFF Remarks For selecting ON or OFF for the extender display. For selecting ON or OFF for the shutter speed display. For selecting ON or OFF for the filter No. display. For selecting ON or OFF for the AWB PRE/A/B display. For selecting ON/OFF of the gain currently selected, S.GAIN, DS. GAIN and LINE MIX GAIN displays. OFF: Neither the super iris ON status nor the aperture value is displayed. IRIS: Only the aperture value is displayed. S+IRIS: Both the super iris ON status and aperture value are displayed. S: The super iris ON status is displayed. O The display of the aperture value and the display of the iris override are interlinked. When the iris override is changed, it is forcibly displayed for 3 seconds. For setting to record the camera ID. BAR: The camera ID is recorded when the color bar signals are recorded. OFF: It is not recorded. For setting the position to display the camera ID. UPPER R: Top right UPPER L: Top left LOWER R: Bottom right LOWER L: Bottom left For selecting an option to display year/month/day and hour/minute/second simultaneously when the camera ID is displayed. For selecting ON or OFF for the zoom position display. For selecting ON or OFF for the color temperature display. For selecting ON or OFF for the system mode display. For selecting ON or OFF for the camera mode display.

7-4-5 VF INDICATOR2

Item TAPE Variable range ON OFF ON OFF ON OFF TCG TCR TCG/TCR OFF Remarks For selecting ON or OFF for the remaining tape amount display. For selecting ON or OFF for the battery voltage display. For selecting ON or OFF for the audio level meter display. For selecting the time code which is to be displayed. TCG: The time code generator value is displayed in the E-E mode. TCR: For displaying the time code reader value during playback TCG/TCR: In EE mode, the time code generator value is displayed from the connectors; in playback mode, the time code reader value is displayed. OFF: The time code is not displayed at any time. For selecting how VTR warnings are displayed. ALWAYS: It is displayed every time a warning has occurred. NORMAL: It is displayed for 3 seconds when a warning has occurred and also for 3 seconds after recording has started and after recording has finished. OFF: It is not displayed at any time. For selecting ON/OFF of the compression mode, which is to be displayed. ON: COMP will be displayed when the COMPRESSION MODE item (the VTR FUNCTION screen on the VTR MENU page) is set to DARK. OFF: It is not displayed at any time. For setting the operation of the SAVE lamp. SAVE&TAPE: The lamp lights up when the VTR SAVE/STBY switch has been set to the SAVE position. It is off during recording. As the tape is approaching the end, it starts flashing in tandem with the warning alarm. SAVE: The lamp lights up when the VTR SAVE/STBY switch has been set to the SAVE position. It is off during recording.

P.ON IND

WHITE PRESET ON OFF

EXTENDER ON OFF

B.GAMMA ON OFF

MATRIX ON OFF

COLOR CORRECTION ON OFF

FILTER ON OFF

7-5 OPERATION

7-5-1 CAMERA ID

Item ID1: Variable range ********** Remarks CAMERA ID setting 1

7-5-3 SHUTTER SELECT

Item POSITION1 SEL For 59.94 Hz Variable range 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF 1/60 1/120 1/250 1/500 1/1000 1/2000 HALF For setting POSITION 2. the shutter speed for For setting POSITION 1. Remarks the shutter speed for
ID2: ********** CAMERA ID setting 2
ID3: ********** CAMERA ID setting 3
<Note> If READ FACTORY DATA is selected, this setting will be cleared.

For 50 Hz

7-5-2 SHUTTER SPEED
Item SYNCHRO SCAN Variable range ON OFF Remarks For selecting SYNCHRO SCAN as the shutter speed to be used.
POSITION2 SEL For 59.94 Hz

POSITION1

POSITION2
ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF
For selecting POSITION1 as the shutter speed to be used. For selecting POSITION2 as the shutter speed to be used. For selecting POSITION3 as the shutter speed to be used.
1/100 1/120 1/250 1/500 1/1000 1/2000 HALF 1/60 1/120 1/250 1/500 1/1000 1/2000 HALF

POSITION3

POSITION4
For selecting POSITION4 as the shutter speed to be used. For selecting POSITION5 as the shutter speed to be used. For selecting POSITION6 as the shutter speed to be used. POSITION3 SEL For 59.94 Hz

POSITION5

POSITION6

For setting POSITION 3.

shutter

7-5-4 USER SW

Item POSITION4 SEL For 59.94 Hz Variable range 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF 1/60 1/120 1/250 1/500 1/1000 1/2000 HALF For setting POSITION 5. the shutter speed for For setting POSITION 4. Remarks the shutter speed for Item USER MAIN SW Variable range INH S.GAIN DS.GAIN LINE MIX S.IRIS I.OVR S.BLK B.GAMMA AUDIO CH1 AUDIO CH2 REC SW Y GET RET SW PRE REC DRS INH S.GAIN DS.GAIN LINE MIX S.IRIS I.OVR S.BLK B.GAMMA AUDIO CH1 AUDIO CH2 REC SW Y GET RET SW PRE REC DRS INH S.GAIN DS.GAIN LINE MIX S.IRIS I.OVR S.BLK B.GAMMA AUDIO CH1 AUDIO CH2 REC SW Y GET RET SW PRE REC DRS Remarks For setting the function to be allocated to the USER MAIN button. For details, refer to 4-9-3 Allocating function to the USER MAIN, USER1 and USER2 buttons.

SHOCKLESS AWB OFF FAST NORMAL SLOW1 SLOW2 SLOW3

AWB AREA 25% 50% 90%

S.BLK LVL OFF 30 ON OFF

AUTO KNEE SW

SHD,ABB SW CTL ON OFF
For selecting ON/OFF of the AUTO KNEE function. When it is set to OFF, the AUTO KNEE may not function even if the AUTO KNEE switch is turned ON. For the setting to adjust the black shading automatically when the AUTO W/B BAL switch is held to the ABB side for 8 seconds or more. For selecting the color bar to be used. SMPTE: Color bar complied with the SMPTE standards FULL BARS: Full color bar SPLIT: SPLIT color bar for SNG (Satellite News Gathering) ARIB: Color bar complied with the ARIB standards For selecting the method used to release the super gain mode. L/M/H: The mode is released by making a change in the L/M/H switch position and the S.GAIN switch (USER switch). S.GAIN: The mode is released using only the S.GAIN switch (USER switch). For selecting the method used to release the digital super gain mode (cumulative gain). L/M/H: The mode is released by making a change in the L/M/H switch position and the DS.GAIN switch (USER switch). DS.GAIN: The mode is released using only the DS.GAIN switch (USER switch).

COLOR TEMP PRE 2300K;

COLOR BARS For AJ-HDX900P For AJ-HDX900E SMPTE FULL BARS SPLIT ARIB

AWB A TEMP 2300K;

AWB B TEMP 2300K;

S.GAIN OFF L/M/H S.GAIN

DS.GAIN OFF L/M/H DS.GAIN

7-5-7 USER SW GAIN

Item S.GAIN 30 dB Variable range 2 O Remarks For selecting whether or not to enable a setting of 30 dB for SUPER GAIN. 2 : The 30 dB setting is enabled. O : The 30 dB setting is disabled. For selecting whether or not to enable a setting of 36 dB for SUPER GAIN. 2 : The 36 dB setting is enabled. O : The 36 dB setting is disabled. For selecting whether or not to enable a setting increase of 6 dB for DS.GAIN. 2 : The 6 dB setting increase is enabled. O : The 6 dB setting increase is disabled. For selecting whether or not to enable a setting increase of 10 dB for DS.GAIN. 2 : The 10 dB setting increase is enabled. O : The 10 dB setting increase is disabled. For selecting whether or not to enable a setting increase of 12 dB for DS.GAIN. 2 : The 12 dB setting increase is enabled. O : The 12 dB setting increase is disabled. For selecting whether or not to enable a setting increase of 15 dB for DS.GAIN. 2 : The 15 dB setting increase is enabled. O : The 15 dB setting increase is disabled. For selecting whether or not to enable a setting increase of 20 dB for DS.GAIN. 2 : The 20 dB setting increase is enabled. O : The 20 dB setting increase is disabled.

DETECTION (DIG)

7-7-5 WHITE SHADING
Item CORRECT Variable range ON OFF 255
LENS R GAIN OFFSET Remarks
For selecting ON or OFF for the white shading compensation. For executing the white shading compensation manually. The sawteeth-shaped waveform and the parabola waveform of the respective RGB channels are adjusted in the horizontal direction and the vertical direction. LENS B GAIN OFFSET

+200 200

R H SAW R H PARA R V SAW R V PARA G H SAW G H PARA G V SAW G V PARA B H SAW B H PARA B V SAW B V PARA
For compensating Bch sensitivity of the lens used.

LENS R FLARE

+200 000
For adjusting the flare level of Rch.

LENS G FLARE

For adjusting the flare level of Gch.

LENS B FLARE

For adjusting the flare level of Bch.
O Data adjusted on the LENS FILE ADJ screen can be stored on an SD memory card as a lens file.

7-8 VTR MENU

7-8-1 VTR FUNCTION
Item HUMID OPE Variable range ON OFF Remarks For selecting whether or not to continue operation when HUMID alarm state has occurred. ON: Operation continues until tape slack is detected even when the HUMID alarm state has occurred during operation. OFF: Operation is stopped as soon as the HUMID alarm state occurs. If the HUMID alarm state occurs during recording, the recording operation will continue unless tape slack is detected regardless of whether ON or OFF has been selected as this items setting. For selecting how recording start is to be accepted. For selecting the time during which REC/ PAUSE is to continue.

7-8-2 BATTERY/TAPE

Item BATTERY SELECT Variable range PROPAC14 TRIMPAC14 HYTRON50 HYTRON120 DIONIC90 DIONIC160 NP-L7 ENDURA7 ENDURA10 ENDURA D PAG L95 BP-GL65/95 NICD14 TYPE A TYPE B AC_ADPT PROPAC14 TRIMPAC14 HYTRON50 HYTRON120 DIONIC90 DIONIC160 NP-L7 ENDURA7 ENDURA10 ENDURA D PAG L95 BP-GL65/95 NICD14 TYPE A TYPE B ON OFF Remarks For selecting the type of battery to be used. The remaining charge is detected in accordance with the battery which has been selected. The variable range is changed by the item settings selected on the 7-8-3 BATTERY SETTING1 and 7-8-4 BATTERY SETTING2 menus. The initial value for TYPE A is set to DIONIC100 while the same for TYPE B is set to HYTRON100.

AUTO MANUAL

TRIMPAC14

DIONIC160

HYTRON50

HYTRON120

ENDURA7
O When the digital battery is attached in the unit, the remaining capacity of the battery is displayed in percent.

7-8-4 BATTERY SETTING2

Item ENDURA/ Variable range Remarks For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. For selecting the voltage at which the battery charge is to be considered nearly depleted in 0.1 V steps when MANUAL has been selected as the setting for the menu item above. For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. For selecting the voltage at which the battery charge is to be considered nearly depleted in 0.1 V steps when MANUAL has been selected as the setting for the menu item above. END 2 / For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. For selecting the voltage at which the battery charge is to be considered nearly depleted in 0.1 V steps when MANUAL has been selected as the setting for the menu item above. For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. For selecting the voltage at which the battery charge is to be considered nearly depleted in 0.1 V steps when MANUAL has been selected as the setting for the menu item above. Item NICD/ Variable range Remarks For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting in 0.1 V steps the voltage at which the battery charge is to considered nearly depleted.

NEAR END

15.0 END 11.0
For selecting in 0.1 V steps the voltage at which the battery charge is to be considered depleted.

ENDURA-D

TYPE A
15./ For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. / : The selection is disabled. For selecting in 0.1 V steps the voltage at which FULL is to be displayed.

17.0 NEAR END 11.0

For selecting in 0.1 V steps the voltage at which the battery charge is to be considered nearly depleted.

15.0 11.0

PAG L95

TYPE B

BP-GL65/95

7-8-5 MIC/AUDIO1

Item FRONT VR CH1 Variable range FRONT W.L. REAR ALL OFF FRONT W.L. REAR ALL OFF FRONT REAR W.L. OFF FRONT REAR W.L. OFF FRONT REAR W.L. OFF FRONT REAR W.L. OFF ON OFF ON OFF ON OFF Remarks For setting whether or not to make the audio control operational for the input system selected for CH1. Item TEST TONE Variable range NORMAL ALWAYS OFF CHSEL Remarks For selecting the test signal. NORMAL: The test tone signal is output to all the channels when the CAM/BAR switch has been set to BAR and the CH1 AUDIO IN switch has been set to FRONT. ALWAYS: The test tone signal is always output to all the channels when the CAM/ BAR switch has been set to BAR. OFF: The test tone signal is not output. CHSEL: The test tone signal is output to the channels for which the CH1 or CH2 AUDIO IN switch has been set to FRONT when the CAM/BAR switch is set to BAR. It is not output to CH3 or CH4.

FRONT VR CH2

For setting whether or not to make the audio control operational for the input system selected for CH2.

MIC LOWCUT CH1

For selecting the microphone low-cut filter for CH1.

MIC LOWCUT CH2

For selecting the microphone low-cut filter for CH2.

MIC LOWCUT CH3

For selecting the microphone low-cut filter for CH3.

7-8-6 MIC/AUDIO2

Item Variable range ON OFF Remarks For selecting the phantom power supply for the front microphone.

MIC LOWCUT CH4

For selecting the microphone low-cut filter for CH4.

FRONT MIC POWER

LIMITER CH1
For selecting the limiter for CH1. REAR MIC POWER ON OFF For selecting the phantom power supply for the rear microphone.

LIMITER CH2

For selecting the limiter for CH2. MONITOR SELECT STEREO MIX For selecting the format of the signals to be output to the monitor.

AUTO LEVEL CH3

For selecting the automatic adjustment of the recording level.
FRONT MIC LEVEL 40dB 50dB For selecting the input level of the front microphone.
AUTO LEVEL CH4 ON OFF For selecting the automatic adjustment of the recording level.
REAR MIC CH1 LVL 50dB 60dB For selecting the input level of the rear microphone.
CUE REC SELECT CH1 CH2 CH3 CH4 CH1+2 CH3+4 For selecting the signals to be recorded on the CUE track.
REAR MIC CH2 LVL 50dB 60dB For selecting the input level of the rear microphone.
REAR LINE IN LVL For AJ-HDX900E For AJ-HDX900P 3dB 0dB +4dB For selecting the rear line input level.
<Note> The frequency characteristics when the microphone low-cut filter is applied are 200 Hz to 10 kHz.
AUDIO OUT LVL For AJ-HDX900E For AJ-HDX900P 3dB 0dB +4dB For selecting the rear audio output level.

FIRST REC TC REGEN PRESET
UB MODE USER TIME DATE EXT TCG FRM RATE REGEN

P.OFF LCD DISPLAY ON OFF

TC OUT TCG TCG/TCR

TC DISP SEL 30F 24F

VITC UB MODE USER/EXT TIME DATE TCG FRM RATE REGEN

TC VIDEO SYNCRO 2 3

REC REVIEW REGEN ON OFF

7-9 OPTION MENU

7-8-8 UMID SET/INFO
Item COUNTRY Variable range NO-INFO Remarks For inputting the name of the users country. NO-INFO is displayed until this is input. For inputting the name of the users organization or company. NO-INFO is displayed until this is input. For inputting the users name. NO-INFO is displayed until this is input. For displaying the ID number of the product. TOTAL CHROMA G 40

7-9-1 OPTION

Item ENG SECURITY Variable range ON OFF Remarks For selecting whether or not to place a restriction on the opening and closing of the MENU screen. ON: The MENU screen can no longer be opened. To release this restriction, consult your dealer. OFF:No restriction is placed on the opening and closing of the MENU screen. For setting the chroma level of the PR signals and the PB signals.

ORGANIZATION NO-INFO

USER NO-INFO

DEVICE NODE

CHROMA OUTPUT
+40 ON OFF FRAME RATE MENU When this is set to OFF, the color elements of the video signals are eliminated. For setting the users bits to record when the video system is set to 24P or 24PA, or when the recording format is set to 720P. FRAME RATE: For recording the shooting information (frame rate etc.) of the camera MENU: This follows the settings in the UB MODE item and the VITC UB MODE item of 7-87 <TC/UB> screen. This is the menu for expanding the DCVPRO connector. Use with DFLT in normal operation. For setting the interval between packets.

7-8-9 VTR DIAG

Item OPERATION Variable range Remarks For displaying the total time during which the power has been on. For displaying the total time during which the drum has rotated.

FRAME RATE UB

DRUM RUNNING
THREADING For displaying the total number of times cassettes have been loaded. For displaying the total time during which the drum has rotated after resetting. For displaying the total number of times cassettes have been loaded after resetting. For displaying the software version of the VTR SYSCON microcomputer. For displaying the software version of the SERVO microcomputer. For displaying the software version of the LCD microcomputer. For displaying the version of the FPGA for video signal processing. For displaying the version of the PLD for controlling the SD memory card. 1394 CONFIG DFLT 1

Panasonic Broadcast Mechanical Parts List

MODEL:

AJ-HDX900P/E/MC

CONTENTS

CASING & FRAME ASSEMBLY....PRT-1 OVERALL SECTION....PRT-1 [A] CASSETTE COVER ASSEMBLY...PRT-4 [B] SIDE CASE (L) ASSEMBLY...PRT-4 [C] L SIDE SECTION....PRT-5 [D] SIDE CASE (R) SECTION (1)...PRT-5 [D] SIDE CASE (R) SECTION (2)...PRT-6 [E] SIDE CASE (R)1 ASSEMBLY...PRT-7 [F] FRONT CASE SECTION...PRT-8 [G] FRONT CASE 1 ASSEMBLY...PRT-8 [H] CAMERA ASSEMBLY (1)....PRT-9 [H] CAMERA ASSEMBLY (1)....PRT-10 [J] BOTTOM CASE SECTION...PRT-11 [K] SHOULDER PAD ASSEMBLY....PRT-12 [L] TOP CASE SECTION (1)...PRT-12 [L] TOP CASE SECTION (2)...PRT-13 [M] HANDLE SECTION....PRT-13 [N] HANDLE COVER SECTION...PRT-14 [P] TOP OPERATION SECTION....PRT-14 [Q] RECEIVER COVER ASSEMBLY...PRT-14 [R] BACK CASE SECTION....PRT-15 [S] JACK PANEL SECTION....PRT-16 [T] BOTTOM COVER ASSEMBLY....PRT-16 [U] SIDE JACK ASSEMBLY....PRT-16
MECHANICAL CHASSIS ASSEMBLY (1)... PRT-17 MECHANICAL CHASSIS ASSEMBLY (2)... PRT-19 MECHANICAL CHASSIS ASSEMBLY (3)... PRT-21 PACKING PARTS ASSEMBLY... PRT-23
CASING & FRAME ASSEMBLY OVERALL SECTION (1)
D SIDE CASE (R) SECTION (Page PRT-5, 6)
C L SIDE SECTION (Page PRT-5) R BACK CASE SECTION (Page PRT-15) (Refer to "R- 8 ")
2 B SIDE CASE (L) ASS'Y (Page PRT-4)
1 A CASSETTE COVER ASS'Y (Page PRT-4) 13 12
SIDE JACK U ASS'Y (Page PRT-16)

107 111

Ref.No.

Part No.

Part Name & Description

OVERALL SECTION (1)

Remarks
VYF3116 VYP9178 VMP7620 VMT1435 VWJ40G7145L0 VWJ40G7180L0 VEE1C35 J0KE00000104
CASSETTE COVER ASS'Y SIDE CASE (L) ASS'Y CONNECTOR SUPPORT ANGLE CONNECTOR CUSHION FLEX. CABLE FLEX. CABLE L SIDE CABLE FERRITE CORE

109 111

XYN2+F6FJ XSB3+6FJK XYN3+J6FJ XYN26+F6FJ XSB3+16FJK VHD1774
SCREW SCREW SCREW SCREW SCREW SCREW

OVERALL SECTION (2)

105 Back side View of CAM DSP P. C. Board. 24 E113 E113 EE15

102 102

102 E17

E12 102

EE11 102
VEP85227A VEP81246 VEP81247A
HEAD BUFF P.C.BOARD CAMERA POWER P.C.BOARD VTR POWER P.C.BOARD
VWJ50G7032L0 VEE0W15 VXY1963 J0KG00000011 VSC5876
FLEX. CABLE RF POWER CABLE MECHANISM ASS'Y FERRITE CORE SHIELD SHEET

1 (M) 1 1

E16 E17
XYN2+F6FJ XYN26+J6FJ XYN3+J6FJ XYN26+J4FJ XYN26+F6FJ
SCREW SCREW SCREW SCREW SCREW

E4 E9 E10 E11 E12 E13

VEP23665A VFP21292A VEP23657A VEP86354A VEP84405A VEP85226A
ADC P.C.BOARD CAM DSP P.C.BOARD CAM DSP SUB P.C.BOARD ECC-SYSCON P.C.BOARD CUE P.C.BOARD RF EQ P.C.BOARD

OVERALL SECTION (3)

L TOP CASE SECTION (Page PRT-12, 13)
18 H CAMERA ASS'Y (Page PRT-9, 10) 110

105 105

T BOTTOM COVER ASS'Y (Page PRT-16)
R BACK CASE SECTION (Page PRT-15)

110 104

20 S JACK PANEL SECTION (Page PRT-16) P4529

P4255 P4256 P4521

J BOTTOM CASE SECTION (Page PRT-11)
VYK1W80 VMP7858 VWJ16G8100L0 VWJ24G7035L0 VEQ4535
BOTTOM COVER ASS'Y SHIELD PLATE FLEX. CABLE FLEX. CABLE CAMERA ASS'Y
XSB3+6FJK XSN3+12FJK XYN3+J6FJ XYN26+C6FJ XSB3+8FJK
A CASSETTE COVER ASSEMBLY
Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 2

B SIDE CASE (L) ASSEMBLY

52 Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. : Lock tight
CASSETTE COVER ASS'Y (VYF2881)
VMG1582 VMT1696 VMT1698 VXA8105 VSC5735 VMX3348 XSB3+16FJK XSB3+12FJK XSB3+6FJK
HEAT SINK (D) GASKET (A) GASKET (C) GROUND PLATE ASS'Y
ELECTRIC CONDUCTION SHEET (1)
2 FOR AJ-HDX400P ONLY 1 FOR AJ-HDX400E ONLY 1 FOR AJ-HDX400E ONLY 3 3

A-1 A-2 A-3 A-4 A-5

VGB0276 VGQ7133 VSC5736 VSC5737 VSC5738
PANASONIC BADGE CASSETTE COVER CLAW
ELECTRIC CONDUCTION SHEET (2) ELECTRIC CONDUCTION SHEET (3)
B-8 B-9 B-10 B-11 B-50 B-51

GROUND PLATE (3)

WASHER SCREW SCREW SCREW

A-50 A-51 A-52 A-53

XNKV0001 VMX2605 XSB26+14FJK XSB26+4FJK

NUT WASHER SCREW SCREW

B-52 B-53
SIDE CASE (L) ASS'Y (VYP8823)

B-1 B-2 B-3 B-4 B-5 B-6

VMG1270 VMG1512 VGB0540 VMG1504 VMG0832 VGB0609
E.E CAP GUARD DVCPRO HD BADGE
CASSETTE WATERPROOF RUBBER

1 (1m) 1

TUBE EX BADGE

C L SIDE SECTION

D SIDE CASE (R) SECTION (1)
E SIDE CASE (R) 1 ASS'Y (Page PRT-7) 20mm 1

C-1 C-2

VEK0K35 VMT1613

L SIDE ACC`Y BNC CUSHION

VEE0W26 VEE0W22
YEARPHONE CABLE TOGGLE SW CABLE

D-25 D-32

WZTU1014B-1M TUBE VHN0382 XYN2+J6FJK VEP80C64A NUT SCREW HP P.C.BOARD

VEP80D61A

L SIDE P.C.BOARD

D-41 D-50

SIDE CASE (R) SECTION (1) D-1 D-2 D-6 D-9 D-11 D-12 D-13 D-14 D-15 D-17 D-18 D-19 D-20 K0E112G00033 VYP9173 VGU9302 VGU8585 VGQ7244 VMG1505 VMX3283 VMP7602 VMS7304 VMT1433 VGH3361 VMS7629 VMB3907 TOGGLE SWITHC SIDE CASE (R) 1 ASS'Y VR KNOB REAR OPERATION BUTTON PHONE JACK COVER VG WATERPROOF RUBBER SHEET VR KNOB COLOUR REAR VR HOLDER ANGLE REAR VR POST WATERPROOF CUSHION VR NEME PLATE SPACER HELICAL SPRING 2
D SIDE CASE (R) SECTION (2)

EE37 E54 E5 E26 E41 54

SIDE CASE (R) SECTION (2)
VMX1312 VMX3355 VGQ3417 VGQ3418 VGQ4723 VMX0531 VHN0194 XTN26+6GFJ XQN2+A2FJK XYN26+J6FJ XYN2+F6FJ XYN2+C5FJ
WASHER SPACER PUSH BUTTON HOLDER A PUSH BUTTON HOLDER B RUBBER HOLDER COVER CLUCH SPACER NUT SCREW SCREW SCREW SCREW SCREW
D-3 D-4 D-5 D-7 D-8 D-10 D-16 D-21 D-22 D-24 D-26 D-27 D-28 D-29 D-30 D-31 D-33 D-34
VYF2895 VMZ3650 VGU9301 VGU9303 VMG0646 VEK0H99 VGU8993 VMG1085 VGU7688 VMP7599 VEE0W25 VEE0W21 VEE0W24 VGH4653 VGH4680 VGU9304 VJF1535 VMT1494
OPERATION PANEL (B) ASS'Y LCD BARRIER VR KNOB FRONT VR KNOB WATERPROOF SHEET SPEAKER ASS'Y OPERATION BUTTON SLIDE SW WATERPROOF RUBBER SLIDE SW COVER (B) TOGGLE SW HOLDER ANGLE FRONT HP CABLE FRONT VR CABLE USER SW CABLE VR NAME PLATE VR NAME PLATE OPERATIN RUBBER BUTTON CLAMPER WATERPROOF CUSHION
D-36 D-37 D-38 D-39 D-40 D-41 D-51 D-52 D-53 D-54 D-55
D-E8 D-E25 D-E26 D-E27 D-E28 D-E29
VEP84403A VEP80C59A VEP80C60A VEP80C61A VEP80C62A VEP80C64A
AUDIO LCD P.C.BOARD SYNCHRO P.C.BOARD FR VR P.C.BOARD USER P.C.BOARD TOGGLE P.C.BOARD HP P.C.BOARD
E SIDE CASE (R) 1 ASSEMBLY

: Lock tight 23 21

Ref.No. Part No.
SIDE CASE (R)1 ASS'Y(1)(VYP9173)

Pcs Remarks Ref.No.

E-1 (1m) E-19 E-20 E-21 E-22 E-23 E-24 E-25 E-50 E-51 E-52 E-53 E-54 E-55 E-56
VKN0149 VMG1092 VMG1096 VMG1195 VMS5505 VMP5578 VGH4295 VMT0809 VMX3348 XYN3+C6FJ XTN3+6GFJ XSB26+5FJ VMX3284 XSB3+10VJK XYN26+J6FJ
SPEAKER NET WATERPROOF RUBBER VR WATERPROOF RUBBER SLIDE SW RUIBBER (A) PIN LSLIDE SW HOLDER ANGLE FILTER NAME PLATE CUSHION (C) WASHER SCREW SCREW SCREW WASHER SCREW SCREW
E-1 E-2 E-3 E-3-1 E-4 E-5 E-6 E-7 E-8 E-9 E-10 E-11 E-12 E-13 E-14 E-15 E-16 E-17
VYP8684 VMG1418 VYF3117 VSQ1050 VMT1426 VMT1427 VMG1506 VMG0832 VDB1757 VKW2683 VGL1039 VGL0512 VGU7696 VGU7697 VGU7698 VGK2886 VGU8130 VKF2818
OPERATION PANEL ASSEMBLY WATERPROOF RUBBER (B) OPERATION DOOR ASS'Y RUBBER MAGNET FACE PAD WATERPROOF SHEET DOOR CUSHION TUBE DOOR HINGE (B) DISPLAY WIINDOW LED BACK LIGHT LED BACK LIGHT SHUTTER BUTTON (+) SHUTTER BUTTON (-) OPERATION BUTTON TOGGLE SW PLATE SLIDE SW COBER (A) SLIDE DOOR

F FRONT CASE SECTION

52 EE23
FRONT CASE 1 ASS'Y G 1 (Page PRT-8) 5

G FRONT CASE 1 ASSEMBLY

: Lock tight
Ref.No. Part No. Part Name & Description
FRONT CASE SECTION F-1 F-2 F-3 F-4 F-5 F-6 F-7 F-8 F-9 VYK1R08 VGU9299 VGQ7131 VMT1432 VGU9861 VMG1317 VEE0W38 VMG1140 VMX3298 FRONT CASE 1 ASS'Y MENU BUTTON BUTTON HOLDER PLATE WATERPROOF CUSHION MENU KNOB MENU WATERPROOF RUBBER FRONT JOG CABLE RAIN COVER SPONGE POST (2.6SQ-13) 1 G-50 F-50 F-51 F-52 F-53 XXEV2W4FP XYN3+C6FJ XYN26+J6FJ VMX1312 SCREW SCREW SCREW WASHER G-51 XYN2+C4FJ XSB2+4FJK SCREW SCREW G-1 G-2 G-3 G-4 G-5 G-6 G-7 G-8 VMG0832 VJF1256 VMG0948 VMC1210 VMP4850 VMS4088 VKF2485 VXU1620
FRONT CASE ASS'Y (VYK1R08) TUBE CABLE CLAMPER EVF RUBBER SHIELD FRONT DOOR PLATE SPRING FRONT DOOR ANGLE FRONT DOOR ANGLE PIN FRONT DOOR RUBBER BUTTON ASS'Y

F-E23 F-E24

VEP80C57D VEP80C58C
FRONT SW P.C.BOARD MENU SW P.C.BOARD

H CAMERA ASSEMBLY (1)

E only E5 E22

CAMERA ASS'Y (VEQ4535)

XQN2+B25FJ XQN2+C4FJ XYN26+C4FJ XYN26+J6FJ XYN3+J6FJ XWC3BFJ
SCREW SCREW SCREW SCREW SCREW WASHER
H-3 H-6 H-9 H-12 H-13 H-22 H-25 H-26 H-31 H-32 H-33 H-34
VEE0X28 VMP8675 VWJ14G8065L0 VSC5864 VSC5865 J0KD00000070 J0KD00000101 VSC5866 VWJ10G8037L1 J0KG00000001 VJF1158 VEE1C34
EARTH CABLE P.C.BOARD HOLDER ANGLE FRONT PULSE FFC SHIELD CASE (DRIVE) SHIELD CASE (PULSE) FERRITE CORE FERRITE CORE SHIELD CASE (PREAMP) SENSOR FFC FERRITE CORE BIND PREAM CABLE ASS`Y

H-51 H-54 H-55 H-56 H-60

H-E1 H-E2 H-E3 H-E5
VEP20B25C VEP23650A VEP23653A VEP23652A
CCD SENSOR P.C.BOARD DRIVE P.C.BOARD PULSE P.C.BOARD PRE AMP P.C.BOARD

H CAMERA ASSEMBLY (2)

Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type.
F FRONT CASE SECTION (Page PRT-8) 53 4
XQN2+C4FJ XSB3+6FJK XXEV26W3FP XQS2+A4FJK XYN26+F6FJ XQN2+A4FJK
SCREW SCREW HEX SCREW SCREW SCREW SCREW
H-2 H-4 H-5 H-11 H-14 H-15 H-16 H-17 H-18 H-20 H-21 H-23 H-29
VEE1C32 VGU8687 VGU8686 VYQ3863 VMA0T71 VMA0T72 VMA0T73 VXQ1446 VDS0169 VDW1228 VMA0N88 VMA0U87 VEE2804
ND/CC FILTER CABLE ASS'Y FILTER KNOB (CC) FILTER KNOB (ND) HEAD OPTICAL ASS'Y HEAT SINK (R) HEAT SINK (G) HEAT SINK (B) LPF ASS'Y MOUNT CAP MOUNT RING PIN GUIDE HEAT SINK BASE GND CABLE

H-52 H-53 H-57 H-59 H-61

PRT-10

J BOTTOM CASE SECTION

SHOULDER PAD ASS'Y (Page PRT-12) 5 K

E6 E56 16

10 E22 9

Accessories

J-1 J-2 J-3 J-4 J-5 J-5 J-6 J-7 J-8 J-9 J-10 J-11 J-12 J-13 J-14 J-15 J-16 J-17 J-18

Remarks Ref.No.

J-19 J-20 J-21 J-22 J-23 J-24 J-25 J-26 J-50 J-51 J-52 J-53 J-54 J-55 J-56 J-57 J-E6 J-E7 J-E22

1 5PIN CONNECTOR

VGM2155 VKN0170 VMT1425 VGQ7172 VYQ3763 VYQ3764 VMP4853 VGF0964 VMT1430 VEE1C33 VEE0W20 VYQ2306 VMZ3360 VMX3351 VKC0560 K1TZB9A00030 VEE0W16 VMP7617 VMX3512
BOTTOM CASE SECTION BOTTOMCASE BOTTOM NET BUTTON CUSHION BOTTOM LOCK PIECE SHOULDER PAD ASS'Y SHOULDER PAD ASS'Y LENS CONNECTOR ANGLE FRONT FOOT GUARD FRONT FOOT CUSHION LENS CONNECTOR ASS'Y FRONT MIC CABLE FOOT BASE REAR AUDIO INSULATION SHEET SPACE SHEET HINGE SDI CABLE POWER CABLE POWER CABLE COVER BUSH
VMP7751 VJF1535 J0KG00000001 VJF1158 VSC5739 VMT1633 VMT1700 VSC5875 XYN3+F8FJK XYN26+J6FJ XSN26+8FJK XSS3+8FJK XTN3+10JFJK XSB26+5FJ XQN2+A3FJ VHD1774 VEP80D60A VEP84404A VEP80C55B
P.C.B. MOUNT ANGLE CLIP FERRITE CORE BIND GROUND PLATE (2) FPC CUSHION GASKET (E) MIC SHIELD CASE SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW MOTHER P.C.BOARD REAR AUDIO P.C.BOARD FRONT MIC P.C.BOARD
1 FOR AJ-HDX900P 1 FOR AJ-HDX900E,MC 2

PRT-11

K SHOULDER PAD ASSEMBLY
E only 6 E only 52 P only 50

L TOP CASE SECTION (1)

P TOP OPERATION SECTION (Page PRT-14) 4 6
Q RECEIVER COVER ASS'Y (Page PRT-14)
SHOULDER PAD ASS'Y (VYQ3763,VYQ3764)
VKN0150 VJF0909 VMP6778 VMT1265 VEE0W17 VEE0W28 VEE0W43 VKN0171 VSC5558 VHD1462 XYN26+C4FJ XSN2+6FJK XSB4+6FJK XSS2+4FJK XYN26+C5FJ
NET (FRONT) CABLE CLAMPER RECEUVER BOX (C) CUSHION GPS CONNECTOR ASS'Y WIRELESS CONNECTOR ASS'Y EVF CONNECTOR ASS'Y NET (REAR) RECEIVER HEAT SINK SCREW SCREW SCREW SCREW SCREW SCREW
K-1 K-2 K-3 K-4 K-5 K-6 K-50 K-51 K-52
VMX3512 VML3912 VGQ7173 VMB3750 VMX3296 VMX3531 XYN3+F8FJK XYN26+J5FJ XSS3+6FJK
BUSH SHOULDER SLIDE LEVER SHOULDER LOCK PIECE SHOULDER RELEASE SPRING SLIDE SHEET BUSH SCREW SCREW SCREW
3 AJ-HDX900E,MC:2PCS 1 FOR AJ-HDX900E,MC ONLY 3 AJ-HDX900E,MC:2PCS FOR AJ-HDX900E,MC ONLY
L-10 L-11 L-12 L-13 L-14 L-15 L-17 L-23 L-50 L-51
TOP CASE SECTION (1) L-1 L-2 L-4 L-5 L-6 L-7 L-8 VGM2070 VMZ3378 VYF2894 VMP7898 VMP7589 VMP7590 VMG1508 TOP CASE SHIELD SHEET RECEIVER COVER ASS'Y RECEIVER BOX (A) RECEIVER BOX (B)
GPS CONNECTOR HOLDER ANGLE

L-L-54 L-55 L-63

RUBBER CAP

PRT-12

L TOP CASE SECTION (2)
M HANDLE SECTION (Page PRT-13) 59

60 x3 20

M HANDLE SECTION
N HANDLE COVER SECTION (Page PRT-14)

TOP CASE SECTION (2)

HANDLE SECTION
L-3 L-16 L-18 L-19 L-20 L-21 L-22 L-24 L-25 L-52 L-56 L-57 L-58 L-59 L-60 L-61 L-62 L-64
VYQ3866 VMG1530 VLP0186 VJF0980 VGU9401 VGM2168 VSC5555 J0KG00000001 VJF1158 VHD1793 XYN3+C4FJ XYN3+F8FJ XWA3BFJK XSB3+8FJK XXEV26W4FP XVE4A25VW XYN26+J6FJ XSS2+4FJK
SLIDER ASS'Y O-LING FERRITE CORE CLAMPER SHAFT LOCK LEVER VF BASE HEAT SINK (B) FERRITE CORE BIND SCREW SCREW SCREW WASHER SCREW HEX SCREW HEX SCREW SCREW SCREW

1 J0KE2 2

M-1 M-5 M-6 M-7 M-8
VYH0361 VGL0783 VMP5585 VMG0955 VMG0956
HANDLE TALLY COVER P.C.BOARD ANGLE P4 O-RING P8 O-RING

M-50 M-52 H-53 M-E31

XYN2+F5FJ XSB3+12FJK XXA5C5FJK VEP80A74D
SCREW SCREW MINUS BOLT BACK TALLY P.C.BOARD

PRT-13

N HANDLE COVER SECTION

P TOP OPERATION SECTION

Q RECEIVER COVER ASSEMBLY

HANDLE COVER SECTION

RECEIVER COVER ASS'Y (VYF2894)

N-1 N-2

VKF3678 VMG1502
HANDLE COVER HANDLE RUBBER

Q-1 Q-2 Q-50 Q-51

VMT1421 VMP7587 VMX3341 XSB3+8FJK XSB3+6FJK XTN2+4GFJ VMX1558
RECEIVER COVER CUSHION RECEIVER COVER ANGLE CUT WASHER SCREW SCREW SCREW CUT WASHER
TOP OPERATION SECTION P-1 P-2 P-3 P-4 P-5 P-6 P-50 P-51 P-E18 VGK2304 VKF2817 VGU8218 VMB2917 VMS5860 VEE0W18 XUC12VM XTN2+4GFJ VEP86149A VTR OPERATION BASE VTR OPERATION DOOR VTR OPERATION BUTTON DOORSPRING DOORSHAFT OPERATECABLE E-RING SCREW OPERATEP.C.BOARD 1

Q-52 Q-53 Q-54

PRT-14

R BACK CASE SECTION

Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 10

Black Red

14 (80mm) : Lock tight 11

Accessorie

BACK CASE SECTION
VMX2605 XSN26+6FJK XSB3+4FJK XSB3+6FJK XYN26+J6FJ VHD1774 XYN26+C6FJ
WASHER SCREW SCREW SCREW SCREW SCREW SCREW
R-1 R-2 R-3 R-5 R-6 R-7 R-8 R-9 R-10 R-11 R-12 R-13 R-14 R-16 R-17 R-18 R-19
VYK0Z63 VJF1476 VGF0960 VGF1058 VMX2606 VJF1347A VKC0601 VJF1498 VJR0696 VEE0W31 VEE1C28 VEE0W44 VMG0832 J0KG00000001 VJF1158 VGQ1712 VGF1057
BACK CASE 1U BATTERY ADAPTER B CONNECTOR COVER BACK CASE COVER SPACER BATTERY HOLDER HINGE (REAR) TERMINAL HOLDER CONNECTOR TERMINAL BATT CABLE ANTON CABLE BATT 2 CABLE TUBE FERRITE CORE BIND ANP BASE BACK BLIND SHEET

1 W/TUBE 1

R-51 R-52 R-53 R-54 R-55 R-56

VEP80D89A

INTERFACE

(1m) 1 1

PRT-15

S JACK PANEL SECTION

E50 12

T BOTTOM COVER ASSEMBLY

U SIDE JACK ASSEMBLY
Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. E5
S-1 S-2 S-3 S-4 S-5 S-6 S-7 S-8 S-9 S-10 S-11 S-12 S-13 S-14 S-15 S-50 S-51 S-E20 S-E30
VGM2175 VGU9300 VGL1038 VMG1508 VMG1511 VMG1085 VMG1523
JACK PANEL SECTION REAR JACK PANEL SLIDE SW KNOB BOTTOM TALLY COVER RUBBERCAP RUBBER CAP (C) RAIN COVER RUBBER BNC RUBBER CAP
T-1 T-2 T-3 T-4 T-5 T-50 T-51
VMT1442 VGQ7132 VMG1417 VMP6370 VMG0954 XSS26+6FJK XSB3+6FJK
BOTTOM COVER ASS'Y (VYK1W80) LED CUSHION BOTTOM PROTECT PLATE BRAKER CAP BACK LOCK ANGLE REAR FOOT SCREW SCREW
K1SYYYYA0002 CONNECTOR (FEMALE) K1AY104J0002 VEE1C30 VEE1B06 VMP8153 VMG1656 J0KG00000011 VEEIC29 XSN26+6FJK XSN26+6FC VEP80C52C VEP80D49A DC OUT CONNECTOR ASS'Y ECU CONNECTOR ASS'Y AUDIO OUT CONNECTOR ASS'Y CONNECTOR CAP ANGLE DC OUT CONNECTOR CAP FERRITECORE DC OUT CABLE SCREW SCREW REAR JACK P.C.BOARD EXT DC P.C.BOARD
SIDE JACK ASS'Y U-1 U-2 U-3 U-4 U-5 U-6 U-7 U-50 U-51 U-E32 VGM2176 VMG1654 VMG0832 VJF1555 VJF1491 VMG1635 VEE1B45 XYN2+J6FJ XSB2+6FJK VEP80D12G SIDE JACK CASE RUBBER CAP (A) SHIELD TUBE CONNECTOR HOLDER A CONNECTOR HOLDER B 1394 CONNECTOR CAP IEE1394 SCREW SCREW 1394 CNT P.C.BOARD 1 (1m) 1

PRT-16

MECHANICAL CHASSIS ASSEMBLY (1)

17 16-109 16

PRT-17

16 16-27

VEM0841 VEM0842 VXP1699C VMA0S69 VMD2588 L9AABYYB0001 VXL2705 VXL2706 VXA5582 VML3097 VXL2615C VMB2973 VXL2653C VWJ1848 VMB3168 VMB3080 VEK7694C VXA8213C
Part Name & DescriptionPcs
S REEL MOTOR ASS'Y T REEL MOTOR ASS'Y IDLER ARM ASS'Y M LOCK/RELEASE BRAKE RELEASE SOLENOID M CASSETTE BRAKE (S)A ASS'Y M CASSETTE BRAKE (T)A ASS'Y M CASSETTE BRAKE BASE ASS'Y CONNECTION ARM A CONNECTION ARM B ARM RELEASE SPRING CONNECTION ARM C MIC FPC LOCK SPRING M CASSETTE BRAKE SPRING CASSETTE DOWN PHOTO ASS'Y M SENSOR SW BASE ASS'Y (M) (M)

OR VEK7694C

XQN2+A3FJ XQN2+CF3FJ XQN2+A15FJ VMX0967 XQN2+CF4FJ
SCREW SCREW SCREW CUT WASHER SCREW

PRT-18

MECHANICAL CHASSIS ASSEMBLY (2)

53-14-4 14-3 14-32 110

53-1 107

55 117

PRT-19
13 13-14-1 14-2 14-53-1 53-61
VXA6630 VED0519 VXA6067 VMB2935 VEG1708 VXA5715C VEM0645C L9AABYYB0002 VXA8117C VES0918C VMA0A35 VXL3027C VXL2871C VMB3304 VXL3274 VXP1866 VMB3220 VXA6173 VXA8082C VXL3318C VMD3731 VXA8124 VHD0561 VXA7362 VXP1683C VXL2772 VMB2950 VXL3320C VMS5906 VMS5905 VMS5904 VMB2929 VMB2933 L2BB00000003 VEK0H98C VMA0T22 VXA8035C VXL2835C VXL2588C VXA8021C VXL3251C VXA8020C VXA8019C VXA8042 VXA5627C VDG1166 VDG1443 VDG1444 VXL2889C VDG1168 VMB2937 VXL2600C VXA8278 VMB2934 VMB3051 VXA6077C VXA8064C L9AAAYYB0002 VMA9877 VMM0429 VXQ0556 VMT0871 VMT0872 VMS7595 VMZ2737 VMB4089 VMB3192
A/C HEAD BASE (1) ASS'Y A/C HEAD A/C HEAD BASE (2) ASS'Y A/C HEAD HIGHT SPRING CYLINDER UNIT EMERGENCY SHAFT HOLDER ASS' LOADING MOTOR (1) ASS'Y PINCH SOLENOID MOTOR ANGLE ASS'Y MODE SW ASS'Y PINCH SOLENOID BASE CLEANING ARM ASS'Y T2 ARM ASS'Y T2 ARM SPRING TENSION ARM A ASS'Y TENSION ROLLER TENSION LEG SPRING MAGNET HOLDER ASS'Y TENSION REG.SPRING HOOK U S1 LOADING ARM ASS'Y LOADING RAIL T1 BOAT ASS'Y HEX SCREW S5 POST BASE A ASS'Y T4 CONNECTION GEAR ASS'Y T4 ARM ASS'Y T4 THRUST SPRING T LOADING ARM ASS'Y T3 UPPER FRANGE T3 SLEEVE T3 LOWER FRANGE T3 SPRING PINCH RELEASE SPRING DEW SENSOR LED HOLDER P.C.BOARD PINCH SOLENOID ANGLE TENSION SENSOR ASS'Y PINCH ARM ASS'Y PINCH GUIDE ARM ASS'Y T SECTOR GEAR ASS'Y TENSION REG. GUIDE ARM S SECTOR GEAR ASS'Y T4 SECTOR GEAR ASS'Y MAIN ROD ASS'Y THRUST SHAFT HOLDER ASS'Y MOTOR WARM GEAR EMERGENCY GEAR A MOTOR EMERGENCY GEAR B MAIN CAM ARM ASS'Y MAIN CAM GEAR A/C HEAD ADJUST SPRING EJECT ARM ASS'Y T1 GUIDE ASS'Y SPRING CLEANER RETURN SPRING CLEANER BASE 1 ASS'Y CLEANER SOLENOID ASS'Y CLEANER SOLENOID CLEANER SOLENOID BASE CLEANER INTERLOCK THRUST SCREW ASS'Y SILENCER A SILENCER B AZIMUTH SLEEVE MODE SW COVER SPRING SPRING 1

135 136

XQN2+AM2FJ XQN2+CF5FJ XQN2+CF3FJ XQN2+CF4FJ XUC12FP XVE2B4FJK XVE2B6FP XVE2B12FP VXQ1156 VMX0967 VMX1061 VMX1079 XWA2BFJ XWE2FJ XWE16VW XXE2A6FP XWG2FJ XWGV15Z32G VHN0365 VHN0312 XQN2+AQ35FJK XQN2+BQ55FJK XQN2+A15FJ XQN2+A5FJ XWGV2Z4G XYN2+J6FJ XYN2+J5FJ XQN2+CM3FJ XQN2+C4FJ VMX0967 XQN2+AM3FJ XYN2+J7FJ
SCREW SCREW SCREW SCREW E-RING HEX SCREW HEX SCREW HEX SCREW SCREW CUT WASHER WASHER CUT WASHER WASHER WASHER WASHER HEX SCREW WASHER WASHER NYLON NUT NUT SCREW SCREW SCREW SCREW WASHER SCREW SCREW SCREW SCREW CUT WASHER SCREW SCREW 2 1

(M) (M) (M) (M) (M)

(M) (M) (M)

103 104

VHD0356 XQN2+A3FJ XQN2+A2FJ XQN2+A35FJK

SCREW SCREW SCREW SCREW

PRT-20
MECHANICAL CHASSIS ASSEMBLY (3)

104 23

106 E110 21

110 16

109 106

PRT-21

VXA8012 VXA6362 VMC1290 VML3100 VMX0967 VMB2961 VXA6050 VDG0387 VXA6365 VXA6367 VXL2896 VXL2740 VMB2981 VMB3025 VXA5632C VXA5631C VDP1880 XWGV4Y6G VMA0T40 VMA0T43 VXA6368 VMA0T33 VSC5732
CASSETTE COMPARTMAENT TOP PLATE ASS'Y CASSETTE PRESSURE SPRING ADAPTOR STOPPER CUT WASHER SPRING SIDE PLATE (R)(1) ASS'Y DUMPER BACK PLATE ASS'Y SIDE PLATE (L)(1) ASS'Y RATCHET LOCK LEVER ASS'Y RATCHET ARM RATCHET SPRING SPRING T RECEIVER ANGLE ASS'Y S RECEIVER ANGLE ASS'Y MAIN ARM ROLLER WASHER H-BUFF ANGLE SUB CHASSIS CASSETTE HOLDER ASS'Y RF EQ ANGLE (T) SHIELD ANGLE 1 (M) 2 1

109 110

XYN2+C8FJ XUC2FP XWGV3Y5G XQN14+A3FJ XWGV2Y4G XQN2+CF3FJ XYN3+C5 XQN2+A2FJ XYN26+J6FJ XYN3+C4FJ
SCREW E-RING WASHER SCREW WASHER SCREW SCREW SCREW SCREW SCREW

VEP82248L

SERVO P.C.BOARD

PRT-22

PACKING PARTS ASSEEMBLY

E only

MC only MC only 13 MC only 13 MC only 13

MC only 13

13 MC only 13 MC only

MC only 14

PRT-23

PACKING PARTS ASSEMBLY

VYQ2741 VPF1176 VQT0X86 VQT0X87 VQT0X88 VYQ2742 VPG1H87 VPG1H88 VPG1H89 VYQ3868 VFC4149 VGU8322 XYN2+J6FJK VPF1016 VPK2298 VPK2280 VPN1791 VPG0T77
CUSHION U (UPPER) POLYETHYLENE BAG OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS CUSHION U (LOWER) PACKING CASE PACKING CASE PACKING CASE OPERATING INSTRUCTIONS SHOULDER BELT KNOB SCREW POLYETHYLENE BAG ACCESSORY BOX (B) ACCESSORY BOX (A) CORNER PAD PACKING CASE (OUT) 8 1
FOR AJ-HDX900P FOR AJ-HDX900E FOR AJ-HDX900MC FOR FOR FOR FOR AJ-HDX900P AJ-HDX900E AJ-HDX900MC AJ-HDX900E (CD-R)
FOR AJ-HDX900MC FOR AJ-HDX900MC

PRT-24