ORDER No.0154 I0

AUTOMOTIVE ELECTRONICS

HONDA CQ-EH9160A

AM/FM MPX ELECTRONIC TUNING RADIO with Stereo Cassette Tape Player and 6-Disc CD Changer
PART No. : 39100-S6M-A100 ID CORD : 1TJ2 VEHICLE : ACURA RSX DESTINATION : North America PRODUCED AFTER : Apr., 2001

Specification*

General Power Supply DC 12V (11V - 16V), Test Voltage 13.2V Negative Ground Current Consumption Output Voltage Output Impedance Less than 1.0A (at VOL. MAX) More than 400mVrms 1.5k Weight** AM Radio Frequency Range Usable Sensitivity 530 - 1,710kHz 24dB/V (S/N 20dB) * Specifications and the design are subject to possible modification without notice due to improvements. ** Dimensions and Weight shown are approximate. FM Stereo Radio Frequency Range Usable Sensitivity 87.75 - 107.9MHz 6dB/V (S/N 30dB) Doldy noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trade marks of Dolby Laboratories Licensing Corporation. Cassette Player Reproduction System Tape Speed Wow and Flutter Signal to Noise Ratio 4-Track, 2-Program Stereo 4.76cm/sec. Less than 0.2% (WRMS) More than 40dB 2.4kg Dimensions** (WHD) 180102165mm CD Player Signal to Noise Ratio Total Harmonic Distortion Channel Separation More than 70dB (IHF-A) Less than 0.4% More than 50dB (IHF-A)

HONDA / CQ-EH9160A

CONTENTS
1 FEATUERS 2 LASER PRODUCTS 3 REAR VIEW 4 FRONT VIEW AND FUNCTIONS 5 WIRING CONNECTIONS 6 BLOCK DIAGRAM (Main, Display, Tape Block) 7 BLOCK DIAGRAM (CD Servo Block) 8 TERMINALS DESCRIPTION 9 ALIGNMENT INSTRUCTIONS 10 ALIGNMENT POINTS 11 CD DISC CENTERING ALIGNMENT 12 PACKAGE AND IC BLOCK DIAGRAM 13 REPLACEMENT PARTS LIST 14 EXPLODED VIEW (Unit) 15 CD CHANGER PARTS LIST 16 EXPLODED VIEW (CD Deck-1) 17 EXPLODED VIEW (CD Deck-2) 18 EXPLODED VIEW (CD Deck-3) 19 TAPE PLAYER PARTS 20 EXPLODED VIEW (Tape Deck) 21 WIRING DIAGRAM 22 SCHEMATIC DIAGRAM (1) 23 SCHEMATIC DIAGRAM (2)

1 FEATUERS

PLL (Phase Locked Loop) synthesized tuning. 18-station preset (12-FM, 6-AM). 6-Disc CD changer (in dash board). Dolby noise reduction. Electronic control of power and sound. Correspondence with BOSE Amp. Anti-Theft function.

3 REAR VIEW

2 LASER PRODUCTS
4 FRONT VIEW AND FUNCTIONS

5 WIRING CONNECTIONS

6 BLOCK DIAGRAM (Main, Display, Tape Block)
7 BLOCK DIAGRAM (CD Servo Block)

8 TERMINALS DESCRIPTION

Pin No. 59 60

Main Block

Port BEEP IDC-ST/SP EVOL CLK EVOL DATA SEC-LED VOL A VOL B LCD-CLK LCD-DI LCD-DO RESET XT2 XT1 VSS X2 X1 REGOFF REGC VDD VOL C VOL D LCD-CE BOSE SEC-CS SEC-CLK SEC-DI SEC-DO SET-SEC1 SET-SEC2 SET-TIME P.CONT ACC CNT AMPCNT LCD ON TUNER +B PLL-CE PLL-DO PLL-CLK PLL-DI VSS VDD AREA ST-IND CA.PON CM.PON M2 M1A M1B T.IN MSM A/B M2F EQ(MTL) F/R DOLBY T.LOAD MS(PL/FF) MS REMO3/4 BUSOUT Description Beep output CD.C start/stop Electronic volume clock Electronic volume data Security LED on/off Rotary encoder data Rotary encoder data Shift clock for LCD data LCD data LCD data Reset input Crystal oscillator terminal Crystal oscillator terminal Ground Crystal oscillator terminal Crystal oscillator terminal (Connecting to VDD) (Connecting to VDD) +5V power supply Rotary encoder data Rotary encoder data LCD driver enable (VDD pull-up) Security ROM chip select Data shift clock for security ROM Serial data Serial data (Ground pull-down) (Ground pull-down) (VDD Pull-up) COM8V power switch ACC 5V power switch Amp power control LCD illumi. on/off Motor antenna power PLL chip select PLL data Shift clock for PLL data PLL data Ground +5V power supply (Ground pull-down) FM stereo detection Tape power control Tape power control Main motor control Loading motor control Loading motor control Tape-in detection MS gain contrl Tape side detection Main motor control Metal tape mode selection Tape head change Dolby NR on/off Tape loading detection MS mode selection MS detection (VDD pull-up) Not used I/O O O O O O I I O O I I I I O I O O I O O O O O O O O O I I O O O O O I O I O O O O I O I (V) 0 4.0 4.9 0.5 0.5.4.9 2.4 0.2.3 1.8 4.9 4.9 4.9 4.8 0.4.0 4.9 4.8 4.9 4.9 4.9 4.5.4.0.3 4.9 4.0 4.0 4.4.4.9 -

IC601 : C2CBHG000069

99 100
NAVI-IN NC NC NAVI-MUTE BIT1 END.A END.B BIT2 EQ BIT3 NC NC IC/VPP REMO SW.A SW.B F-MUTE R-MUTE NC VSM AMP MUTE AVDD AVREF1 AVSS NC NC ACC-DET TAPE EJ BUS.IN GAIN IDCEJECT BAT-DET EJ.INH IDC-SI RXD TXD IDC-CLK IDC-SO CD-RESET CDON

(ACC5V pull-up) No connection No connection Navi mute control Tape mode switch Tape end signal Tape end signal Tape mode switch Metal/Normal switchl Tape mode switch No connection No connection (Connecting to ground) Remote control signal CD.C mute Not used Front mute Rear mute No connection Phase diff. level detection Not used +5V power supply Analog reference voltage Ground (Connecting to ground) No connection ACC level detection Tape eject SW Not used (+5V pull-up) CD disc eject SW Battery level detection Tape/Disc eject SW CD.C serial data Not used Not used Shift clock for CD.C data CD.C data CD.C reset CD.C controller enable
O I I I I I I O O O O I I I I I I I O O O O O
4.4.6 1.5 2.4 4.5.0.6 4.9 5.0 4.5 4.6 4.8 4.8 4.7 4.5 4.4 4.4.9 4.9 1.2 4.9 4.9
Note : Voltage measuerments are with respect to ground, with a voltmeter (Internal resistance : 10M ohms.)
Pin No. 1, 4-40 41-45-49 50-59 60

Display Block

Port S1, 2 S3 S4-40 COM1-3 S41 KS2-6 KI1-4 KI5 TEST VDD VDD1 VDD2 VSS OSC Description Disc LED on/off Not used LCD segment data LCD common LCD segment data Key strobe Key data (Connecting to ground) (Connecting to ground) +5V power supply LCD angle LCD angle Ground Oscillator terminal I/O O O O O O I (V) 0 2.5 2.5 2.5 0.5.1 3.3 1.3.9

IC901 : YEAMLC75853

DO CE CL DI
Key data output LCD driver chip enable Shift clock for LCD data LCD data input

O I I I

Pin No. 15 16-22,51 52-56 57-63

CD Servo Block

Port VDD D0 D1 /WE /RAS D2 D3 /CAS0 /CAS1 A8 A7 A6 A5 A4 A9 A0 A3 VSS2 VDD2 TVD PC ECS TRD FOD FBAL TBAL VREF FE TE RFENV OFT /RFDET BDO LDON ARF IREF DRF DSLF DSLF2 PLLF VCOF AVDD2 AVSS2 OUTL AVSS1 OUTR AVDD1 FLAG FCLK TX MCLK MDATA MLD Description +5V power supply D-RAM data D-RAM data D-RAM data write D-RAM row address strobe D-RAM data D-RAM data D-RAM columun address strobe D-RAM columun address strobe D-RAM address D-RAM address D-RAM address D-RAM address D-RAM address D-RAM address D-RAM address D-RAM address Ground +5V power supply Not used Traverse motor control Not used Spindle motor control Tracking coil drive Focus coil drive Focus balance Tracking balance Refence voltage Focus error Tracking error RF envelope Off track signal RF detecting signal Drop-out signal Laser on signal RF signal Reference current input Bias for DSL Loop filter for DSL Loop filter for DSL Loop filter for PLL Not used +5V power supply Ground L channel output Ground R channel output +5V power supply (Connecting to ground) Flag output Frame clock Not used Not used Clock for I/F command Date for I/F command I/F command load I/O I/O I/O O O I/O I/O O O O O O O O O O O O O O O O O I I I I I I I O I I I I/O I/O I/O O O O O I I I (V) 5.0 2.3 1.8 4.9 3.4 0.3.0.6 1.1 0.1.1 0.4 1.0 5.0 2.5 2.4 2.5 2.4 1.9 3.0 2.5 2.5 2.5 2.4.5 2.5 1.2 2.4 2.5 2.2 1.4 5.2.2.3 4.1.0 3.1 5.0

IC201 : MN662783RPW

BLKCK SQCK SUBQ DMUTE STAT /RST CSEL PMCK SMCK SUBC SBCK /CLDCK /TEST X1 X2 VDD1 VSS1
Subcode block clock Ext.clock for sub code-Q Code for sub. code-Q Mute input Status signal Reset input (Connecting to ground) Clock output Clock output Serial data of sub code Shift clock for SUBC Not used (Connecting to VDD) Crystal oscillator Crystal oscillator +5V power supply Ground

O I O I O I O O O I -

0 5.0 3.5.0 5.2.5 2.0.6 5.0 0.4 3.2 5.0 0

IC301 : MN1873260AB4

Pin No. 39 40-Port VDD OSC2 OSC1 VSS XI XO CM VREFH SW13 SW12 SW11 SW10 SW4 SW3 SW2 SW1 VREFL /RESET SCKM SIM SOM SQCK SUBQ CD.ON BLKCK P.ON MUTE SENS CLVS FLOCK TLOCK VMI HMI HVMUTE SW9 SW8 SW7 SW6 SW5 Description +5V power supply Crystal oscillator Crystal oscillator Ground (Connecting to ground) Not used (Connecting to ground) Reference voltage Shuter SW Horizontal origin Clump SW Play SW Shuter SW Tray origin SW Inner SW Outer SW (Connecting to Ground) Reset input (Ground pull-down) Clock for serial data CD changer serial data CD changer serial data Ext. clock for sub. code-Q Code for sub. code-Q Not used (Ground pull-down) CD changer start/stop Not used Sub. code block clock In operation CPU Mute output (Ground pull-down) Servo status Servo status Focus servo lock Tracking servo lock Horizontal motor control Vertical motor control H/V motor mute (Ground pull-down) Disc-in (B) SW Disc-in (L) SW Disc-in (F) SW Disc push SW Tray hight SW I/O I I I I I I I I I I I I O O I I I O O O O O O O O O I I I I I (V) 5.0 2.2 2.5.0 4.9 4.0 4.4.8 4.4.5.0 1.3 4.3 5.0 1.5.5.0 5.0 5.0 0.2.4.5
BDO DQSY /RST STAT DMUTE XE P.DOWN MLD MDATA MCLK SPMT MUTE12 MUTE4 LDOI TRV SYNC
Drop-out signal Not used Reset output Status signal Mute output Not used Power down signal No connection I/F command load Data for I/F command Clock for I/F command Spindle mute Focus/Tracking mute Loading motor mute Loading motor control Forced traverse control Not used
I O I O O O O O O O O I/O I/O -
0 5.0 2.0 5.0 3.1 4.1 5.4.8 2.5 2.4 -

9 ALIGNMENT INSTRUCTIONS

9.1. Alignment Conditions

Balance, Fader Control : center Power Supply Voltage : DC13.2V Output Impedance : 4 Output Power : 0.5W Note : Do not align the FM/AM package block. When the package block is necessary, it will be supplied already aligned at the factory. Bass, Treble Control : Center Dolby NR: OFF

Step (1) (2)

Dolby NR Alignment
Alignment Item DOLBY NR Rch DOLBY NR Lch Test Tape RFKZ0038 RFKZ0038 VTVM Connection TP201 TP301 Adjust VR201 VR301 Remarks Adjust for 388mV 1.0dB Adjust for 388mV 1.0dB

10 ALIGNMENT POINTS

11 CD DISC CENTERING ALIGNMENT
This adjustment is for assuring that compact discs will be placed in the center of the turntable. <Adjustment Condition / Jig> Power Supply Voltage : 13.2V Test Disc : TCD-784M
<Adjustment Procedures> 1. Attach the adjusting screw to the upper chassis (See Figure 1.). 2. Insert the test CD (TCD-784M) into the disc No.1 position and play it. 3. After checking whether the disc is centered on the turntable, turn the adjusting screw unit it is in the center. <Check Items> Check that the disc is correctly centered. Check that the disc is securely clamped. Check that no abnormal noise is produced when clamping the disc. [Directions of Turning the Adjusting Screw] CD stops before its proper position : Turn the screw counterclockwise. CD overruns : Turn the screw clockwise.
4. After the adjustment, lock the screw.
12 PACKAGE AND IC BLOCK DIAGRAM

12.1. Main Block

PK50 : YEP0PTA514B0

IC602 : MN1382KTX

IC205 : C0JBAS000030

IC201 : C1BB00000284

IC611 : YEAMLC72135C

IC702 : AN8065SE1

IC603 : YEAMS29130AD

IC961 : AN6277NK

IC701 : YEAMA61W12ST

12.2. Tape Block

IC1 : YEAMCXA2565Q

12.3. CD Servo Block

IC101 : YEAMBA6354BF

IC603 : YEAMT4W53FUL

IC601 : YEAMBA5971FP

IC202 : C3ABMB000010

IC501 : YEAMPC358G2T

IC401 : YEAMBA6792FY

13 REPLACEMENT PARTS LIST
Notes : 1. Be sure to make your orders of replacement parts according to this list. 2. Important safety notice: Components, identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers specified parts. 3. Location keys in the remarks column indicates the general location of the parts shown in the exploded drawing, as in a road map. 4. The marking (RTL) indicates that Retention Time is limited for this item. After the discontinuation of assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. 5. "MCC" marks in remarks column are indicated supply parts of Matsushita Communication Industrial Corp. of America (MCC).

Part Name & Description Connector, 15P Connector, 14P Case, LCD Upper Cover Bottom Cover Side Plate (L) Side Plate (R) Front Cover Escucheon Assy Knob, VOL. Knob Heat Sink Holder, LED Holder, LCD Optical Shade Insulator Bracket Bracket Bracket, Deck Bracket, IC701 Bracket, Q753 PCB w/Component PCB w/Component Tapping Screw, Tapping Screw, Screw Tapping Screw, Screw Tapping Screw, Tapping Screw, M2x6mm Screw Tapping Screw, M3x6mm Screw, M3x5mm

RTL RTL

LCD LCD901

L5AAALC00020

COILs L923

YELTBMHS800T

LAMPs PL901 PL902 PL903 PL904 PL905 PL906 PL907 PL908
YEALHSIR043 YEALHSIR043 YEALHSIR043 YEALHSIR043 YEALHSIR043 YEALHSIR043 YEALHSIR043 YEALHSIR043
Pilot Pilot Pilot Pilot Pilot Pilot Pilot Pilot
Lamp Lamp Lamp Lamp Lamp Lamp Lamp Lamp
VARIABLE RESISTORs VR901 K9AA015B0013 VR902 K9AA015B0013
Variablr resistor Variablr resistor
Mechanical Parts MISCELLANEOUS ANT51 YEAA10064 AT1 YEFX0213797 AT2 YEFX0213797 AT3 YEFX0213919 AT5 YEAT03346A CNP1 YEAES17A050A
Antenna Receplacle Bracket Bracket Terminal Terminal Connector, 17P

14 EXPLODED VIEW (Unit)

15 CD CHANGER PARTS LIST
15.1. ICs and Transistors

SERVO BLOCK [E8586C]

Ref. No. IC101 IC201 IC202 IC301 IC401 IC501 IC601 IC602 IC603 Q101 Part No. YEAMBA6354BF MN662783RPW C3ABMB000010 MN1873260AB4 YEAMBA6792FY YEAMPC358G2T YEAMBA5971FP C0JBAS0051 YEAMT4W53FUL 2SB766ATX Part Name & Description IC IC IC IC IC IC IC IC IC Transistor Remarks

[E2685A]

Ref. No. Q1 Q2 Q3 Part No. PN147 PN147 PN147 IC IC IC Part Name & Description Remarks
Ref. No. C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C301 C302 C305 C401 C402 C403 C501 C503 C504 C601 C602 C603 C604 C605
Part No. YECUS1H123KX YECUS1C334KX YECUS1C104KX YECSW1C106MS ECEV0JA470SR YECUS1C104KX YECUS1C104KX YECSW1C106MS YECUS1C104KX YECUS1A105KX YECUS1C104KX YECSW1C106MS YECUS1H103KX YECUS1C104KX ECEV1CA470SP YECUS1C104KX YECUS1C104KX YECUS1E273KX YECUS1E393KX YECUS1C104KX ECEV1CA470SP YECUS1C104KX YECUS1C104KX YECUZ1H821KX
Part Name & Description Ceramic, 0.012F 50WV Ceramic, 0.33F 16WV Ceramic, 0.1F 16WV Tantalum, 10F 16WV Electrolytic, 47F 6.3WV Ceramic, 0.1F 16WV Ceramic, 0.1F 16WV Tantalum, 10F 16WV Ceramic, 0.1F 16WV Ceramic, 1F 10WV Ceramic, 0.1F 16WV Tantalum, 10F 16WV Ceramic, 0.01F 50WV Ceramic, 0.1F 16WV Electrolytic, 47F 16WV Ceramic, 0.1F 16WV Ceramic, 0.1F 16WV Ceramic, 0.027F 25WV Ceramic, 0.039F 25WV Ceramic, 0.1F 16WV Electrolytic, 47F 16WV Ceramic, 0.1F 16WV Ceramic, 0.1F 16WV Ceramic, 820pF 50WV

Part No. ERJ6GEYJ471 ERJ6GEYJ471 ERJ6GEYJ471 ERJ6GEYJ471 ERJ6GEYJ471 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ222 ERJ6GEYJ222 ERJ6GEYJ101 ERJ6GEYJ103 ERJ6GEYJ103 ERJ6GEYJ222 ERJ6GEYJ103 ERJ6GEYJ123 ERJ6GEYJ103 ERJ6GEYJ273 ERJ6GEYJ103 ERJ6GEYJ183 ERJ6GEYJ393 ERJ6GEYJ103 ERJ6GEYJ472 ERJ6GEYJ472
Part Name & Description Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, 470 1/10W 470 1/10W 470 1/10W 470 1/10W 470 1/10W 47k 1/10W 47k 1/10W 47k 1/10W 47k 1/10W 47k 1/10W 47k 1/10W 2.2k 1/10W 2.2k 1/10W 100 1/10W 10k 1/10W 10k 1/10W 2.2k 1/10W 10k 1/10W 12k 1/10W 10k 1/10W 27k 1/10W 10k 1/10W 18k 1/10W 39k 1/10W 10k 1/10W 4.7k 1/10W 4.7k 1/10W

15.7. Mechanical parts

MISCELLANEOUS
Ref. No. FXPart No. YEAE012348A YEAP2683 YEATSD00405 YEFA011711G YEFA011713A YEFA011714D YEFA011716 YEFA011718A YEFA011720B YEFA011722A YEFA011724B YEFS04707 YEFV011897 YEFW04158 YEFW04159A YEFW04161A YEFW04167 YEFW05389 YEFW062351 YEFW062461B YEFX003872 YEFX003873 YEFX003874 YEFX003875 YEFX003877 YEFX003878A YEFX003879 YEFX003882A YEFX003883B YEFX003884 YEFX003885 YEFX0031057 YEFX003891A YEFX0031003 YEFX003894 YEFX003895A YEFX003896 YEFX003897A YEFX003898 YEFX003899B YEFX003929 YEFX003931 YEFX003932A YEFX0052269 YEFX0052272 YEFX0052274B YEFX0052275A YEFX0052276A YEFX0052277 YEFX0052278 YEFX0052279 YEFX0052494 YEFX0052447 YEFX0052284 YEFX0052285A YEFX0052287A YEFX0052288A YEFX0052289A YEFX0052290A YEFX0052291B YEFX0052292A YEFX0052335 Part Name & Description Cord w/Connector Suspension FPC Terminal Upper Chassis Assy Side Chassis (R) Side Chassis (L) Assy Suspension Chassis Assy Suspension Chassis(Bottom) Assy Swing Chassis Assy Stocker Plate Assy Main Chassis Assy Damper Insulator Bearing Roller Shaft Holder(L) Feed Screw Housing Disc Collar Stocker Cam Ring Disc Roller Shaft Roller Shaft Assy Elevator Gear(1) Elevator Gear(2) Elevator Gear(3) Elevator Gear(4) Traverse Gear(2) Traverse Gear(3) Traverse Gear(4) Stocker Cam Gear(1) Stocker Cam Gear(2) Stocker Cam Gear(3) Disc Hold Gear Load Gear Push Gear(1) Push Gear(2) Horizontal Cam Gear(1) Horizontal Cam Gear(2) Horizontal Gear(1) Horizontal Gear(2) Horizontal Gear(3) Horizontal Gear(4) Horizontal Cam Gear(3) Horizontal Gear(5) Push Cam Gear FPC Hold Spring Guide Spring(B) Suspension Lock Spring Swing Spring Stocker Spring(1) Stocker Spring(2) Thrust Spring Sencer Lever Spring Damper Spring Balance Spring(1) Push Spring Spring Roller Hold Spring(L) Roller Hold Spring(R) Push Lever Spring Feeder Spring Push Plate Spring Change Spring Guide Spring(F) Remarks (4-A) (1-E) (1-F) (3-B) (1-C) (4-A) (1-D) (1-D) (3-D) (4-F) (3-D) (4-D) (2-F) (3-D) (2-B) (1-E) (2-B) (4-E) (3-F) (2-A) (2-B) (3-F) (2-F) (3-F) (3-E) (3-E) (2-F) (2-D) (2-D) (1-D) (3-F) (3-E) (2-F) (3-E) (2-F) (3-F) (3-B) (3-B) (3-B) (3-D) (2-E) (3-E) (3-E) (3-E) (3-D) (3-E) (3-D) (2-D) (3-B) (2-D) (1-B) (3-D) (3-D) (4-D) (4-E) (4-D) (4-E) (1-E) (1-E) (1-F) (4-D) (3-D) (3-A) (4-B) (2-B) (2-B) (4-E) (4-B) (3-B) (1-D) (2-B)

15.5. Connectors

Ref. No. CN1 CN101 CN301 CN401 CN402 CN501 Part No. YEAE5220715 YEAE5220715 YEAE5227112 YEAE5220706 YEAE5326102 YEAE5227110 Part Name & Description Connector, Connector, Connector, Connector, Connector, Connector, 15P 15P 12P 6P 2P 10P Remarks
Ref. No. JD1 Part No. YEAE5227106 Part Name & Description Connector, 6P Remarks

15.6. Electric Parts

SWITCHES
Ref. No. SW1 SW1 SW10 SW11 SW12 SW13 Part No. ESE102MH4 ESE102MH4 ESE102MH4 ESE102MH4 ESE102MH4 ESE102MH4 Part Name & Description Switch Switch Switch Switch Switch Switch Remarks

CRYSTAL

Ref. No. XL301 Part No. YEXLSTCC737T Part Name & Description Crystal OSC Remarks

CERAMIC FILTERS

Ref. No. XL201 Part No. H2D169500001 Part Name & Description Ceramic Filter Remarks
Ref. No. L101 Part No. YELTLM41P750 Part Name & Description Coil Remarks

Ref. No. 141

Part No. YEFX0052366 YEFX0052495 YEFX0052449A YEFX0052445 YEFX018552 YEFX018553D YEFX018595 YEFX018556A YEFX018596 YEFX018638 YEFX018600 YEFX0461903A YEFX0461905A YEFX0461914B YEFX0461917 YEFX0461918 YEFX0461919A YEFX0461922D YEFX0461924C YEFX0461926A YEFX0461931A YEFX0462062B YEFX219129 YEFX0462002C YEFX0462003B YEFX0462026 YEFS02342 YEFX0462029 YEFX206135C YEFX206136D YEFX206137A YEFX206138C YEFX206139E YEFX206140 YEFX206141A YEFX206143 YEFX206144 YEFX218296 YEFX218299 YEFX219124A YEFX219126D YEFX233504A YEFX233505A YEFX233506 YEFX234192 YEFX249486 YEFX9992184 YEFX9992237 YEFX9991903 YEJT03220 YEP0FX3384 YEP0FX3633 YEP0FX3661S YEP0FX3660S YEP0FX3662S YEP0FX3663S YEFX9992192A YEFX9992193 YEFX0052448 YEFX218308 YEFX0031053 YEFX0031054 YEFX014040 YEP0PT8586A2 YEP0PT2682A0 YEP0PT2684A0 YEP0PT2685A0
Part Name & Description Stocker Thrust Spring Damper Spring (R ) Damper Spring (L) Lock Spring Travese Motor Bracket Assy Guide(F) Bracket Guide(B) Bearing Bracket Stopper Plate Gear Bracket Assy Elevator Motor Bracket Guide Lever (B) Assy Guide Lever (F) Assy Senser Cover Stocker Rack Senser Lever(B) Sneser Lever(FA) Feeder Plate Push Lever Rack Lever Push Lever Escape Lever(1) Guide (F) Guide Cam Plate(F) Guide Cam (B) Plate Assy Lever Guide Plate Assy Felt Feeder Guide Plate Assy Guide(BL) Guide(BU) Guide(FL) Guide(FU) Disc Guide Traverse Guide FPC Guide Disc Guide(S) Disc Guide(U) Disc Roller Disc Roller Guide (B) Base Assy Guide Base (F) Assy Stocker Tray Housing Disc Holder(L) Disc Holder(U) Elevator Cam Feeder Arm Assy Suspension Balancer (1) Stocker Tray Feed Screw Guide Feed Screw Assy Optical Pick-up Assy Spindle Motor Assy Horizontal Motor Assy Vertical Motor Assy Loading Motor Assy Traverse Motor Assy Suspension Balancer Suspension Balancer (3) Balance Spring (B) Roller Load Gear (2) Load Gear (3) Retaining Ring, 2mm PCB w/Component PCB w/Component PCB w/Component PCB w/Component

VARIABLE RESISTORS

Ref. No. VR201, 301 Part No. EVNDXAA00B13 Part Name & Description Variable Resistor Remarks
Ceramic, 0.012F 50WV Ceramic, 0.033F 25WV Ceramic, 0.1F 16WV Electrolytic, 22F 16WV Electrolytic, 33F 10WV Ceramic, 0.01F 100WV Ceramic, 0.033F 25WV Electrolytic, 0.33F 50WV Ceramic, 0.0047F 50WV Electrolytic, 10F 16WV Ceramic, 0.0047F 50WV Ceramic, 0.33F 25WV

19.7. Mechanical Parts

Ref. No. Part No. YGFX0052472 YGFX0052454 YGFX0462100 YGFX0462104 YGFA011830 YGFX234194 YGFX0052427 YGFX209271 YGFX0052471 YGJW04131 YGFX0052475 YGFX0031035 YGFA011827 YGFX0052444 YGP0PT8790A0 YGP9FZ2973 YGFX0462105 YGFX0052478 YGFX0052477 YGFX239470 YGFX0462097 YGFX0031031 YGP0FX3845 YGFX0052474 YGFX218305 YGFX0031033 YGFX0462102 YGFW062600 YGFX218306 YGFX213213 YGFX0031001 YEFX003753B YGFX014075 YGFX003970 YGJT03250 YGFX0052446 YGFX0031030 YGP0FX3846 YGFX030102 YGFX0031026 Part Name & Description Lock Plate Spring Spring Cassette Holder (U) Assy Cassette Holder(L) Head Chassis Assy Cam Back Tension Spring Reel (R) Assy Holding Spring Washer Lack Plate Spring Lack Plate Main Chassis Assy EQ Lever Spring Dolby P.C.B. Assy Head Assy Lever Vibration-proof Spring Spring Cassette Guid Plate PRO Change Plate Idler Gear Plate (F) Assy Main Motor Assy Lack Return Spring Pinch Roller (F) Assy Idler Gear Plate (R) Assy Lack Return Link Lack Return Link Shaft Pinch Roller (R) Assy Flywheel Assy Drive Gear (2) Play Idler Gear Lock Ling Gear Gear Shaft Idler Gear Plate Spring Worm Gear Loading Motor Assy Worm Gear Stopper Drive Gear (3) Remarks
Ref. Part No. No. C1 to 3 YECUS1H471JM Part Name & Description Ceramic, 470PF 50WV Remarks

19.4. Resistors

Ref. No. R201,R207 R301,R307 R402 R403 R404 R405 R406 R408 R409 R501 Part No. ERJ6GEYJ683 ERJ8GEYJ181V ERJ6GEYJ683 ERJ6GEYJ181 ERJ6GEYJ183 ERJ6GEYJ473 ERJ8GEYJ334V ERJ8GEYJ392V ERJ6GEYJ273 ERJ8GEYJ223V ERJ6GEYJ273 ERJ6GEYJ472 Part Name & Description Chip, 68k 1/10W Chip, 180 1/8W Chip, 68k 1/10W Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, Chip, 180 1/10W 18k 1/10W 47k 1/10W 330k 1/8W 3.9k 1/8W 27k 1/10W 22k 1/8W 27k 1/10W 4.7k 1/10W Remarks
Ref. No. R1,2 R3 R4 to 6 R7, 8 Part No. ERJ8GEYJ683V ERJ6GEYJ472 ERJ8GEYJ472V ERJ8GEYJ821V Part Name & Description Chip, Chip, Chip, Chip, 68k 1/8W 4.7k 1/10W 4.7k 1/8W 820 1/8W Remarks

Ref. No. 66 67

Part No. YGFA011851 YGP0PT8791A0 YGFX209270 YGFX0052473 YGFX003971 YEFR03083 YGFX0031029 YEJE01004 YEJE01036 XYN2+J6FX XYN2+C8FX YEJT03167 YEJS06097A YEJT03271
Part Name & Description Drive Chassis Assy Reel P.C.B. Assy Reel (F) Assy Pinch Roller Spring PRO Change Gear Belt Drive Gear E-Ring E-Ring Screw, 2 x 6mm Screw, 2 x 8mm Screw, Screw, 2 x 2.5mm Screw,
20 EXPLODED VIEW (Tape Deck)

22 SCHEMATIC DIAGRAM (1)

22.1. Tape Block

To E-6857A CN962

<Symbol Table>

To E-6857A CN961

23.1. Display Block

23 SCHEMATIC DIAGRAM (2)

6.8 6.12
To Main P.C.B. E-6857A CN902
To Main P.C.B. E-6857A CN901

23.2. Main Block

23.3. CD Servo Block

Printed in Japan (K)

2001.8

(Recycled Paper)

To Main P.C.B. E-8861Ab CN923