Wear gloves for safety. Make sure that wiring is completed before installation. To prevent damage to the unit, do not connect the power connector until the whole wiring is completed. Do not connect more than one speaker to one set of speaker leads. (except for connecting to a tweeter)
Observe the following cautions when installing.
Refer wiring and installation to qualified service personnel.
Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your own installation of the unit.
Observe the following cautions when handling the battery for the remote control unit.
Use only specified battery (CR2025). Match the polarity of the battery with the (+) and () marks Replace a dead battery as soon as possible. Remove the battery from the remote control unit when not Insulate the battery (by placing them in a plastic bag or Dispose of the battery according to the local regulations. Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water. covering them with vinyl tape) before disposal or storage. using it for an extended period of time. in the battery case.
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the product could cause an accident or fire.
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, screws, and moving parts such as seat rails. Do not scratch, pull, bend or twist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by winding them with vinyl tape or similar protection.
In case of battery leakage Thoroughly wipe the battery liquid off the battery case and
If any part of your body or clothing comes into contact If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical attention. with battery liquid, wash it with plenty of water. insert new battery.

CAUTION:

PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING,
INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED.
Safety Information (continued)

THIS PRODUCT IS A CLASS I LASER PRODUCT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
The following applies only in the U.S.A. Part 15 of the FCC Rules
FCC Warning: Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device.
This system is designed so that you cannot see moving pictures while you are driving.
Park your car in a safe place and pull the side brake (parking brake) lever before watching the monitor. A rear monitor (option) displays moving pictures while driving.
Note: Be sure to connect the side brake (parking
NOTICE: This product has a fluorescent lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>
brake) connection lead. (a Installation Instructions)

Notice

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Notes on Use

Liquid Crystal Panel
Do not cause impact to the liquid crystal panel. Usage temperature range: 0 C to 40 C {32 F to 104 F} When the temperature is very cold or very hot, the image may not appear clearly or may move slowly. Also, movement of the image may seem to be out of synchronization or the image quality may decline in such environments. Note that this is not a malfunction or problem. In order to protect the liquid crystal panel, keep it out of direct sunlight while the unit is not in use. Sudden changes in the temperature inside the car such as those which occur immediately after the cars air conditioner or heater has been turned on may cause the inside of the liquid crystal panel to cloud over due to water vapor or it may cause condensation (droplets of water) to form and, as a result, the panel may not work properly. Do not use the unit while these symptoms are in evidence but leave the unit standing for about and hour, and then resume or start use.

q Remove the battery holder with the remote control unit placed on a flat surface. q Stick your thumbnail into the groove and push the holder in the direction of the arrow at the same time. w Pull it out in the direction of the arrow using a tough pointed object. Tough pointed object
USER (user settings)( a page 32) display unit, clock, ID code, memory clear, other SCREEN (screen settings)(a page 34)

dimmer, picture

AUDIO (audio settings)(a page 34)
sound setup, graphic equalizer, CS Auto, speaker setup, speaker level, time alignment, source level, cross over
(DVD settings)(a page 38)
language, display, pro logic, down mix, dynamic range compression, multiple channel
w Put a battery in the case with (+)-side facing up. e Put the case back.
INPUT/OUTPUT (AV-IN/OUT settings)(a page 39)

source skip

Lithium battery (CR2025) Battery case
(radio settings)(a page 40)
FM set up, AM set up Note: Refer to Settings (a page 30) for further information about operations, settings, and others of the menu screen.
Keep batteries away from children to avoid the risk of accidents. If an infant ingests a battery, please seek immediate medical attention.
You may need to set the following depending on the devices to be connected.
Remove and dispose of an old battery immediately. Do not disassemble, heat or short a battery. Do not throw a battery into a fire or water. Follow local regulations when disposing of a battery. Improper use of a battery may cause overheating, an explosion or ignition, resulting in injury or a fire. Note: Battery Information: Battery Type: Panasonic lithium battery (CR2025) Battery Life: Approximately 6 months under normal use (at room temperature)

Subwoofer

Execute

SP LEVEL

(speaker level). (a page 36)
AV1/AV2 (Camcorder, VCR, etc.)

Adjust

SOURCE LEVEL

(AV1/AV2 input level).

(a page 37)
When you connect external devices to AV1-IN/ AV2-IN (AV1/AV2), be sure to connect the side brake connection lead (aInstallation Instructions).
Symbols used in this manual

Pictographs

You can perform some operations of this unit in one or more methods with the touch panel or remote control. This book explains such operations in tabular form as follows. Refer to the following for the pictographs located in the upper part of each table.

Compatible Discs

Disc Marks
The following pictographs are used for the descriptions of disc operation. (a page 19-23)
DVD : DVD VCD : VCD (Video CD) CD : CD MP3 : CD-R/RWs containing MP3 files WMA : CD-R/RWs containing WMA files

How to Call up Operation Screen

Source

Radio (a page 26)

Standard Screen

Operation Screen
Disc Player (DVD/VCD (*1)/ CD/MP3/WMA) (a page 20)
How to Cancel OSD (On Screen Display)

AV1/AV2 (*1) (a page 28)

OSD OFF *2
*1 To switch Operation Screen ON, touch the center of touch panel or press [ENTER]. *2 The operation screen is not available in the video mode. Note: Refer to the description of each mode for how to operate the operation screen.
Showing the hidden part of the screen.
Some items have continued parts. You can see the continued parts by pressing DVD mode or.

General

ASPECT ASP

[TILT]

[OPEN]

TILT TILT CQ-VD7005U

OPEN OPEN

MUTE MUTE

[MUTE]

[SRC] (PWR: power)

[] ] [[ ]

Remote Control Sensor

Preparation: Turn your cars ignition key to the ACC or ON position.

General Operations

Operations

Power Power

ON : OFF :

VTR CH-C

Note: You cannot turn on the power via the remote control when ACC SELECT is set to OFF. (a ACC SELECT , page 33)

Display Open/Close

Press once to open. Press again to close.
Note: When the display is opened or closed, a loud beep sounds three times. If the unit stops halfway, press [OPEN] again to draw it all the way out. Opening/closing the display can be done when the power is off.

Source selection

(a page 14)
[SRC] RADIO (AM/FM) (a page 26) (a page 20) (a page 28) (a System Upgrade Guidebook)
DVD (DVD/VCD (Video CD)/CD/MP3/WMA) AV1/AV2 Sources connected to the Expansion Module (CY-EM100U) *1
*1 When the Expansion Module (CY-EM100U, option) is connected. (a System Upgrade Guidebook)
Note: If there is no external sources connected, AV1/AV2 mode can be set to skip. (a page 39)
Touch/Press and hold for more than 2 seconds

[+] [] (VOL)

General Operations (continued)

Volume

Note: The sound level for each source is stored in memory.

q [+] w []

q Up w Down
Setting Range: 82 dB to 0 dB, default: 40 dB Note: The volume level can be set independently for each source and each disc format. [MUTE] [MUTE] Mutes the sound. To cancel, press again. q Press and hold for more than 2 seconds. w Press to adjust. Setup is the same as from MENU. Refer to DISPLAY UNIT for details. (a page 32)

Mute Tilt Angle

[]] or [[]
Do not touch the unit while the display is moving. Inserting hands, fingers or foreign objects into the unit can cause injuries and damage to the unit.
Note: Vertical angle (TILT) is saved in the memory, so when the display is drawn out next, it is automatically set at the angle and in the position adjusted before. After adjusting its angle, adjust the brightness as well. (a page 34) The car model and installation conditions may impose some restrictions on the adjustment of the monitor's angle.

Folding Down the Display Temporarily
To raise the display, press again. [TILT] Note: Even when the unit power is off, you can fold down the display temporarily.
Avoid physical shock to the monitor. Do not place any object on the display, or subject it to undue force. Do not move the display forcibly. The monitor movable range may be limited by the type of car, the position where the display is mounted, etc.

Before Disc Playback

Discs that can be Played Back

Disc Type

DISC DVD VCD (Video CD) CD CD-R/RW

Symbols used on jackets

(Examples of such symbols include)
: Number of subtitle languages : Number of audio tracks : Number of angles

Mark/logo

Recordable

ReWritable

Disc Size Video Format NTSC/PAL LPCM, MPEG1, MPEG2, dts, Dolby Digital 1 (ALL)

12 cm {5}

The numbers indicate the number of languages, tracks, angles, etc., recorded on the disc. Screen size (H:V aspect ratio)

4:3 LB

: 4:3 standard size : Letterbox (a page 38)

Audio Format

LPCM, MPEG1
LPCM LPCM (CD-DA), (CD-DA), MP3/ dts WMA

16:9 wide size

16:9 LB 16:9 PS

Region No.

Note: About CD-Rs/RWs and DVD-Rs/RWs, refer to Notes on CD-Rs/RWs and DVD-Rs/RWs. (a page 48) Some copy-protected music CDs are not playable.
: Playback in LETTERBOX (letterbox) format on a standard screen (4:3). : Playback in PAN & SCAN (pan and scan) (a page 38) format on a standard screen (4:3).

Notes on DVD-Rs/RWs

Only video formatted discs are playable. Discs in the video recording (VR) format are unplayable. Unfinalized discs are unplayable. Some discs are unplayable depending on the disc itself, device, drive and software that are used for disc recording.
Note: The size of the image that is displayed on the screen depends on the screen mode (Aspect Ratio a page 40), and on the screen size for the content on the disc.
Region Management Information
This product is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this product, this product does not play the disc. The Region number for this product is 1 and ALL.

Example:

Touch/Press and hold

AV1/AV2
Please refer to the separate System Upgrade Guidebook for how to operate this unit when optional devices are connected. Preparation: Connect an optional external device to the AV1/AV2.

AV Mode Selection

You can view the images and listen to the sounds from the connected external devices in the AV1/AV2 mode respectively.
q Touch Source Button. d / w Touch (AV1/AV2) on the Source Selection Screen.
Press [SRC] to change to the desired mode. To switch Operation Screen ON, touch the center of touch panel or press [ENTER]. Note: You can set up the system so that the AV mode is not selected (source skip). (a page 39) (AV set to NAVI INPUT is not skipped even if SOURCE SKIP is set to ON.) is If no operation is performed for 10 seconds or touched, the operation buttons disappear. AV terminal is not used for the Panasonic car navigation system (available in future). Refer to NAVI SETUP for setting. (a System Upgrade Guidebook)

Settings

Preparation: To display menu in French, Execute
USER DISPLAY UNIT CLOCK ID-CODE MEMORY CLEAR OTHER SCREEN DIMMER PICTURE AUDIO SOUND SETUP GRAPHIC-EQ CS Auto SP SETUP SP LEVEL TIME ALIGNMENT SOURCE LEVEL CROSS OVER DVD LANGUAGE DISPLAY DVD SOUND MULTI-CH INPUT/OUTPUT NAVI SETUP CAMERA SETUP SOURCE SKIP INPUT SELECT OUTPUT SELECT H-F SETUP RADIO FM SETUP AM SETUP XM SETUP SIRIUS SETUP User Display adjustment Clock setting ID Code Setting Memory clearance Other settings Screen Adjusting the brightness Display appearance Audio Sound setting Setting and adjusting of graphic equalizer CS Auto setting Setting of the absence/presence of each speaker Adjusting the output balance of each speaker Delay time setting of each speaker Setting the AV1/AV2 input level Cut off frequency DVD Language Setting Appearance of DVD image DVD sound setting Sound output selection Input/output Navigation setting Rear view camera setting Source skip Input selection Output selection Hands-free setting Radio Setting for FM stations Setting for AM stations Setting for XM radio Setting for Sirius satellite radio

MENU DISPLAY

(Language setting). (a page 33)
(a page 32) (a page 32) (a page 32) (a page 33) (a page 33)

(a page 34) (a page 34)

(a page 34) (a page 34) (a page 35) (a page 36) (a page 36) (a page 37) (a page 37) (a page 37)
(a page 38) (a page 38) (a page 39) (a page 39)
(*1) (*1) (a page 39) (*1) (*1) (*1)
(a page 40) (a page 40) (*1) (*1)
(*1) Please refer to the System Upgrade Guidebook.

MENU Operation

(Example: DVD mode)

in Operation Screen.

Touch desired setting.
(Example: setting screen of DISPLAY UNIT a page 32) Determines the setting and goes back to the previous menu out of the menu.
Determines the setting and gets out of the menu.
Note: The display returns to the previous status if there is no operation for more than 60 seconds after changing to the setting menu.

MENU MENU

[SRC] (Exit from the menu)
[MENU] (Shows the menu display/ Goes back to the previous menu)

[] ] [[ ] [}] [{]

(Select/adjust)

(Determine)

Settings (continued)

SCREEN

INPUT/OUTPUT

DISPLAY UNIT

Display adjustment

ID-CODE

ID Code Setting
Prior to operating this unit, it is advisable to assign a 4digit ID code for security. Once the ID code has been set, the unit cannot be operated if the main power supply is disconnected then re-connected. It is electronically locked so that a thief cannot use the stolen unit unless that person knows the code you have set. The ID code operation must be performed only by the person to whom the unit belongs. Generally, it is not necessary to enter the ID code each time when using the unit if it has not been disconnected from the main power supply (car battery).

(Tilt angle adjustment)

default: 5

OPEN/CLOSE

AUTO MANUAL
(Monitor setting when power on)
: the monitor is opened automatically when turning ON ACC. : the monitor is not opened automatically. default:

MANUAL

0 to 9
4 digits numeric code default: none
Note: The monitor position setting menu can also be displayed by pressing the [TILT] button on the main unit for more than 2 seconds. (a page 17)

possible (at least 100 Hz or lower)

CENTER

(Center speaker setting)

SP LEVEL (Speaker level)

Adjusting the output balance of each speaker (Left front speaker output balFRONT L ance)

] : down,

: when not using a center speaker is not possible : for large speakers, when bass playback is possible (at least 100 Hz or lower)
SMALL : for small speakers, or when bass playback LARGE
[ : up (Center speaker output balance)
default: NONE * A center speaker (option, EAB-CF2 recommended) is required.
[ : up (Right front speaker output balance)

FRONT R

(Surround speaker setting)
[ : up (Right surround speaker output balance)
: when not using a surround speaker is not possible : for large speakers, when bass playback is possible (at least 100 Hz or lower)
[ : up (Left surround speaker output balance)
[ : up (Subwoofer speaker output balance)

SUB - W

(Subwoofer speaker setting)
: when using a subwoofer : when not using a subwoofer

[ : up

Setting range: 10 dB to +10 dB (1 dB steps) default: 0 dB for all speakers
default: NO * A subwoofer (option, CJ-SW3003 recommended) is required. A power amplifier (option) is also required for connecting a subwoofer.
Note: While the private mode is active, only adjusted.
If the speaker setting is NONE or NO for a speaker, the test signal is not output and that speaker cannot be selected. Turn rotary volume controller or press [+] or [] (VOL) to adjust the volume of the test signal.

can be

Note: While the private mode is active, only FRONT L and FRONT R can be adjusted.
Setting the AV1/AV2 input level Make this setting if it is not possible to adjust the volume through the connected device (on the output side).

AV1 LEVEL TEST TONE

(Test tone output)

(Setting for AV1)

LOW HIGH
: sets the level low/sound volume increases. : sets the level high/sound volume decreases.
: enables the test tone. : disables the test tone.

AV2 LEVEL

(Setting for AV2)
When the test tone is set to on, test signal (a continuous tone) is output from each speaker for approximately 2 seconds. Adjust the output balance so that the tone appears to have the same volume from each speaker.
Adjusting the output balance: Adjust the volume of all of the other speakers to the volume level of the speaker from which the test signal appears to be the quietest.

TIME ALIGNMENT

Adjusting the timing with which the audio from each speaker reaches the listeners position (Center speaker delay time setCENTER ting)

The angle mark is displayed to indicate the parts where multi-angle data is recorded.
: activates angle mark. : inactivates angle mark. default:

SCREEN AUDIO

DVD SOUND

DVD sound setting

NAVI SETUP (Navigation set up)
(a System Upgrade Guidebook) (5.1 channel listening in Dolby surround sound)

PRO LOGIC

CAMERA SETUP
(a System Upgrade Guidebook)
: activates Pro Logic. : inactivates Pro Logic. default:

SOURCE SKIP

Source skip
Note: This setting is enabled only in the DVD/VCD/CD player mode. ON selection in some audio settings may disable audio output from the subwoofer.

AV1 SKIP

(AV1 skip)
If AV1 is not used, the AV1 mode is skipped when changing the mode.
: skips AV1 : does not skip

DOWN MIX

Lo/Ro Lt/Rt
(To use the down mix function, specify the type.)
: simple stereo down mix (Lo = Left only, Ro = Right only) : surround element decodable down mix (Lt = Left total, Rt = Right total)

AV2 SKIP

(AV2 skip)
If AV2 is not used, the AV2 mode is skipped when changing the mode.
Note: This function is available only when Dolby Digital or dts source is playing and when sound comes out only from the front speakers adjusted with SP SETUP. default:
: skips AV2 : does not skip

DR COMP

(Dynamic Range Compression)
Maintaining the ambience even while listening at a low volume level Compression style selecting
default: OFF Note: When external devices are connected to this unit without involving the Expansion Module (CY-EM100U, option), AV2 SKIP is not enabled because the connected external devices are identified as AV2.

INPUT SELECT

STD MIN OFF
: DR COMP ON : made with the greatest compression, roughly equivalent to a TV broadcast. : DR COMP OFF default:

OUTPUT SELECT

H-F SETUP
MULTI-CH (Multiple channel)
Sound output of Dolby Digital 2 ch. from all speakers
: changes sound from 2 ch. to 5.1 ch. : keeps the source output 2 ch. sound.
USER SCREEN AUDIO DVD INPUT/OUTPUT

Aspect Ratio

Default: NORMAL Mode: 4 types
Press and hold [ASP] on the main unit to change the aspect ratio as follows. [ASP]

FM SETUP

Setting for FM stations

NOISE SUPPRESSION

(FM IF filter switching)
: adjusted automatically received to prioritize noise reduction.
NARROW : narrows the frequency bandwidth to be WIDE
: widens the frequency bandwidth to be received to prioritize sound quality. default:

Common (continued)

The speaker channels are reversed between right and left. The power of the unit fails unintentionally.
The speaker wiring is reversed between right and left. aPerform the speaker wiring in accordance with the wiring diagram.
The safety device works. aConsult your dealer, or your nearest Panasonic Servicenter.

Radio

Antenna installation or wiring of antenna cable is faulty. aCheck whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely connected to the chassis. No power is supplied to the antenna amplifier (when using a film antenna, etc.). aCheck the wiring of the antenna power lead.

Poor reception or noise

The number of auto preset stations is less than 6. Preset stations cannot be stored.
The number of receivable stations is less than 6. aMove to an area where receivable stations number is maximum, and try presetting. The contact of the battery lead is poor, or the battery lead is not always powered. aMake sure that the battery lead is connected securely, and preset stations again.
No playback or disc ejected
The disc is inserted upside down. aInsert a disc correctly. There is a flaw or foreign object on the disc. aRemove the foreign object, or use a flawless disc. There is a flaw or foreign object on the disc. aRemove the foreign object, or use a flawless disc. The unit is not sufficiently secured. aSecure the unit to the console box. The unit is tilted at over 30 in the front-to-end direction. aMake the angle 30 or less. Something such as a peeled label obstructs the disc coming out. aPress and hold the [u] for more than 10 seconds (disc forced ejection). In case that the disc forced ejection does not work, consult your dealer. The microcontroller in the unit operates abnormally due to noise or other factors. aUnplug the power cord and plug it again. In case the unit is still out of order, consult your dealer.

Sound skipping or noise

Sound skipping due to vibration

Disc unejectable

Troubleshooting (continued)

MP3/WMA

No playback or disc ejected The CD-R/RWs that are playable on other devices are not playable on this unit.

The disc has unplayable formatted data. aRefer to the description about MP3/WMA for playable sound data except CDDA (i.e. music CD). The playability of some CD-R/RWs may depend on the combination of media, recording software and recorder to be used even if these CD-R/RWs are playable on other devices such as a PC. aMake CD-R/RWs in a different combination of media, recording software and recorder after referring to the description about MP3/WMA. There is a flaw or foreign objects on the disc. aRemove the foreign objects, or use a flawless disc. For MP3/WMA, refer to the description about MP3/WMA. Playing VBR (Variable Bit Rate) files may cause sound skipping. aPlay Non-VBR files. Note: Refer to Notes on MP3/WMA (a page 24)
Cannot switch the audio language/subtitle language/angle. The audio/subtitle language selected in the DVD settings is not used.
It is not possible to switch if the disc does not have multiple audio languages/subtitle languages/angles recorded on it. (Refer to the guide provided with your disc.) Some discs permit switching through a menu screen. Sometimes, switching angles is possible only with certain scenes.
If audio or subtitles in that language are not recorded on the disc, the audio or subtitles do not switch to that language. (Some discs permit switching through a menu screen. Refer to the guide provided with your disc.)
A DVDR or DVDRW is not playable.
The disc is still unfinalized. aFinalize the disc. Refer to Before Disc Playback (a page 18) or Notes on Discs (a page 48) for other cases. The disc is in the video recording (VR) format. aPlay video formatted discs. Refer to Before Disc Playback (a page 18) or Notes on Discs (a page 48) for other cases.

Display Settings

The brightness of the screen is not stable. The picture is dark. The picture is whitish. Something is wrong with the picture. The picture is light in color. The display does not go back into the unit.
AUTO dimmer is selected. aSelect one of the dimmer levels from among 1 to 4 to make the dimmer adjustment become free from light intensity.
The screen is not adjusted properly. aMake every adjustment of the screen.
The monitor stops on the way to the home position. aPress [OPEN] (CLOSE).

Remote Control Unit

The battery is inserted in the wrong direction. A wrong battery is inserted. aInsert a correct battery in the correct direction. The battery is weak. aReplace the battery with new one.
No response to pressing buttons
The aiming direction of the remote control unit is wrong. aAim the remote control unit at the sensor of the unit and press buttons. The sensor is exposed to direct sunlight. (The remote control unit may not be operable when the sensor is exposed to direct sunlight. In such a case, the system is not faulty.) aBlock off sunlight to the sensor. REAR is selected for the remote control setting. aSelect FRONT for the remote control setting.

If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Servicenter. The product should be serviced only by a qualified technician.

If the Unit Begins to

Malfunction.
Reset switch Insert a hard, slender stick into the hole and push the switch. Important Push the switch only when the unit fails to operate with any buttons. (Stored settings and adjustments are not cleared.) If the unit fails to return to normal condition, call the nearest Panasonic Servicenter and ask for repairs.

Replacing the Fuse

Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher rating, or connecting the product directly without a fuse, could cause fire or damage to this unit. If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.
Reset switch Note: If the ID-CODE has been already set, you will be asked to enter the ID-CODE right after the unit is restarted.

Maintenance

Caution on Cleaning

Alcohol Alcohol

Pesticide Pesticide

Cleaning this Unit

When the unit is dirty, wipe the surface of the display using the Wiping Cloth (supplied).
Cleaning without the supplied cloth
1 Moisten the soft cloth in dishwashing soap diluted with water and wring well. 2 Wipe lightly. Go over the same surface with a dry cloth.

Thinner Thinner

Wax Wax

Benzine Benzine

Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry soft cloth for routine exterior cleaning. Never use benzine, thinner or other solvents.
Note: Since there is the possibility of water drops getting inside of the unit, do not directly apply cleanser to the surface. Do not scratch the screen with your nails or other hard objects. The resulting scratches or marks will obscure the images.
If water drops or similar wet substances get inside the monitor, it may cause a malfunction.

Notes on Discs

How to hold the disc Do not touch the underside of the disc. Do not scratch the disc. Do not bend disc. When not in use, keep disc in the case. Disc insert The surfaces of new discs tend to be slippery. Therefore, when using such a disc for the first time, it may not load satisfactorily even when it has been inserted into the unit. At a time like this, insert the disc into the unit as far as it will go until it is loaded properly.
When inserting a disc into or ejecting and removing it from the unit, insert it straight in or eject and remove it straight out in parallel with the unit. Otherwise, the disc may be scratched or marked in the process. When inserting a disc, do not put one disc on another. Failure to observe this may cause the discs to be jammed.

Installation/Montage/Instalaci n
WARNING/AVERTISSEMENT/ADVERTENCIA

CA-LSR01U

To System-up connector of head unit*(e.g. CQ-RX400U, CQ-RX200U, CQ-C800U, CQ-C700U, CQ-C500U, CQ-C300U, CQ-C8405U, CQ-C8305U, CQ-C7205U, CQ-C7105U, CQ-C5405U, CQ-C5305U, CQ-C3405U, CQ-C3305U, CQ-VX100U, CQ-VW100U, CQ-VD7005U, CQ-VD6505U , CN-NVD905U, CN-NX100U and CN-NW100U)/Expansion Module (CY-EM100U) Au connecteur du systme de l'unit principale*(par ex. CQ-RX400U, CQ-RX200U, CQ-C800U, CQ-C700U, CQ-C500U, CQ-C300U, CQ-C8405U, CQ-C8305U, CQ-C7205U, CQ-C7105U, CQ-C5405U, CQ-C5305U, CQ-C3405U, CQ-C3305U, CQ-VX100U, CQ-VW100U, CQ-VD7005U, CQ-VD6505U , CN-NVD905U, CN-NX100U et CN-NW100U)/Module d'expansion (CY-EM100U). Para conectar la unidad de cabezal con conector System-up*(p. ej. CQ-RX400U, CQ-RX200U, CQ-C800U, CQ-C700U, CQ-C500U, CQ-C300U, CQ-C8405U, CQ-C8305U, CQ-C7205U, CQ-C7105U, CQ-C5405U, CQ-C5305U, CQ-C3405U, CQ-C3305U, CQ-VX100U, CQ-VW100U, CQ-VD7005U, CQ-VD6505U , CN-NVD905U, CN-NX100U y CN-NW100U)/mdulo de expansin (CY-EM100U).
Disconnect the cable while pressing the buttons on both sides. Dbrancher le cble tandis que vous pressez sur les boutons sur les deux cts. Desconecte el cable mientras pulsa los botones a ambos lados.
CA-LSR01U Bottom / Bas du CA-LSR01U / Inferior de CA-LSR01U
Before Wiring / Avant le cblage / Antes de realizar las conexiones How to install the unit / Montage de l'appareil / Instalacin de la unidad

SC INPUT POWER

Disconnect the cable while pressing the buttons on upper side. Dbrancher le cble tandis que vous pressez sur les boutons sur les deux cts. Desconecte el cable mientras pulsa los botones a ambos lados.
Customer Services Directory / Rpertoire des services la clientle U.S.A. Mounting / Montage / Montar
Select a location (carpet, dry surface, etc.) where the main unit should be mounted. Fix the main unit with a double-faced adhesive tape or a velcro tape. Please consult with your local dealer if needed. Choisissez un emplacement (tapis, surface sche, etc.) o l'unit principale doit tre monte. Fixez l'unit principale l'aide d'adhsif double face ou de bande velcro. Veuillez consulter votre revendeur local au besoin. Seleccione una ubicacin (tapete, superficie seca, etc.) para montar la unidad principal. Fije la unidad principal con la cinta adhesiva de doble cara o una cinta con velcro. Consulte a su distribuidor local si fuera necesario. Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: http://www.panasonic.com/support or, contact us via the web at: http://www.panasonic.com/contactinfo You may also contact us directly at: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST. For hearing or speech impaired TTY users,TTY: 1-877833-8855 Accessory Purchases: Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at: http://www.pasc.panasonic.com or, send your request by E-mail to: npcparts@panasonic.com You may also contact us directly at: 1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday-Friday 9 am to 8 pm, EST.) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (We accept Visa, MasterCard, Discover Card, American Express, and Personal Checks) For hearing or speech impaired TTY users, TTY: 1866-605-1277 Service in Puerto Rico Panasonic Puerto Rico, Inc. Panasonic Sales Company Factory Servicenter: Ave. 65 de Infantera, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Phone (787) 750-4300, Fax (787) 768-2910

To Sirius SC-C1 Sirius SC-C1 A Sirius SC-C1
Power Cable Cordon dalimentation Cable de alimentacin

FILTER & FUSE BOX

CANADA
WARRANTY SERVICE FOR PRODUCT OPERATION ASSISTANCE, please contact: Our Customer Care Centre: Telephone #: (905) 624-5505 1-800 #: 1-800-561-5505 Fax #: (905) 238-2360 Email link: Contact Us on www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicentre at www.panasonic.ca: Link : ServicentresTM locator under Customer support IF YOU SHIP THE PRODUCT TO A SERVICENTRE Carefully pack and send prepaid, adequately insured and preferably in the original carton. Include details of the defect claimed, and proof of date of original purchase.
RPARATION SOUS GARANTIE Pour de laide sur le fonctionnement de lappareil, veuillez contacter notre service la clientle au : N de tlphone : (905) 624-5505 Ligne sans frais : 1-800-561-5505 N de tlcopieur : (905) 238-2360 Lien courriel : Contactez-nous www.panasonic.ca Pour la rparation des appareils, veuillez consulter notre site www.panasonic.ca pour connatre le centre de service agr le plus prs de votre domicile : Lien : Centres de service sous support la clientle Expdition de l'appareil un centre de service Emballer soigneusement l'appareil, de prfrence dans le carton dorigine, et lexpdier port pay et assur au centre de service. Inclure la description dtaille de la panne et la preuve de la date dachat dorigine.
CARRY-IN OR MAIL-IN SERVICE For Carry-In or Mail-In Service in the United States, call 1-800-211-PANA (7262) or visit Panasonic Web Site: http://www.panasonic.com For assistance in Puerto Rico, call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910. LIMITED WARRANTY LIMITS AND EXCLUSIONS This warranty ONLY COVERS failures due to defects in materials and workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred during shipment, failures which are caused by products not supplied by the warrantor, failures which result from accident, misuse, abuse, neglect, bug infestation, mishandling, misapplication, alteration, faulty installation, set-up adjustment, maladjustment of consumer control, improper maintenance, improper antenna, inadequate signal reception or pickup, power line surge, improper voltage supply, lightning, modification, commercial use (such as use in hotels, offices, restaurants, or other business uses) or rental use of the product, or service by anyone other than the technician from Factory Servicenter or other authorized service centers, or damage that is attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED WARRANTY COVERAGE". THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the servicer, and loss of media, data or other memory contents. The items listed are not exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to warrantor's Consumer Affairs Department at the addresses of the warrantor. PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY. Customer's Record Model No. Serial No. Dealer's No. Code No. Dealer's Address Date of Purchase

Limited Warranty / Garantie Limite U.S.A.
PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way, Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, DIVISION OF PANASONIC PUERTO RICO, INC. Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park Carolina, Puerto Rico 00985 PANASONIC AUTO PRODUCTS LIMITED WARRANTY LIMITED WARRANTY COVERAGE If your product does not work properly because of defects in materials and workmanship. Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as "the warrantor") will, for the length of the period indicated in the chart below, which starts with the date of original purchase ("warranty period"), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or refurbished product. The decision to repair or replace will be made by the warrantor.
Categories Audio Components (except items listed below) MXE Series Audio Components (except items listed below) Speakers Defective Car Audio Speakers under warranty must be exchanged at the place of purchase. Contact your Dealer for details. Accessories (in exchange for defective items) Parts One (1) Year Two (2) Years One (1) Year Labor One (1) Year Two (2) Years Not Applicable
Specifications / Spcifications / Especificaciones
Power supply: DC 12 V(11-16 V), test voltage 14.4 V, negative ground Current consumption: Less than 1.0 A Dimensions(WxHxD): (Main Unit) 46.7 x 24 x mm {1 13/16" x 15/16" x 42 1/8"} Weight: 0.19 kg {0.4 lbs.} Alimentation : CC 12 V(11 - 16 V), test de tension 14,4 V, terre ngative Consommation actuelle : Moins de 1,0 A Dimensions (LxHxP) : (Unit principale) 46,7 x 24 x mm {1 13/16" x 15/16" x 42 1/8"} Poids : 0,19 kg {0,4 lbs} Fuente de alimentacin: DC 12 V(11-16 V), voltaje de prueba 14,4 V, masa negativa Consumo de corriente: menos de 1,0 A Dimensiones (AxHxP): (Unidad principal) 46,7 x 24 x mm {1 13/16" x 15/16" x 42 1/8"} Peso: 0,19 kg {0,4 lbs}

Ninety (90) Days

Not Applicable
During the "Labor" warranty period, there will be no charge for labor. During the "Parts" warranty period, there will be no charge for parts. You must carry-in or mail-in your product prepaid during the warranty period. If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold "as is". A purchase receipt or other proof of the original purchase date is required for warranty service.