DV1800

D ES T

POP UP

SET UP
MOBILE NAVIGATION SYSTEM NAVIGATIONSSYSTEM SYSTEME DE NAVIGATION MOBILE MOBIEL NAVIGATIESYSTEEM SISTEMA DI NAVIGAZIONE MOBILE

MOVILE NAVIGATION SYSTEM

CN-DV1800EN Installation Instruction
Einbauanleitung Instructions dinstallation Installatie-aanwijzingen Instruzioni per linstallazione
Please read these instructions carefully before using this product and save this manual for future use. Bitte lesen Sie diese Bedienungsanleitung vor der Verwendung dieses Produktes aufmerksam durch und bewahren Sie sie danach fr sptere Nachschlagzwecke sorgfltig auf. Prire de lire ces instructions attentivement avant dutiliser le produit et garder ce manuel pour lutilisation ultrieure. Leest u deze instructie alstublieft zorgvuldig door voor u dit product in gebruik neemt en bewaar deze handleiding voor later gebruik. Si prega di leggere attentamente queste istruzioni prima di usare questo prodotto e di conservare questo manuale per usi futuri.

ENGLISH DEUTSCH FRANAIS

Installation Guide
Preparation 4 Cautions 5 Installation Procedure 6 Attaching the Remote Control Holder 6 Installation of GPS Antenna 7
Wiring Connection 8 Final Check 11
Installationsanleitung 10
Vorbereitungen 12 Vorsichtsmassnahmen 13 Installationsverfahren 14 Anbringen des Fernbedienungshalters 14 Installation der GPS-Antenne 15
Kit-Anschluss 16 Abschliessende Prfung 19

Guide dinstallation 10

Prparation 20 Prcautions prendre 21 Procdure dinstallation 22 Fixation du porte-tlcommande 22 Installation dune antenne de GPS 23
Connexions lectriques 24 Vrification finale 27

NEDERLANDS

Installatieaanwijzingen 10
Voorbereiding 28 Voorzorgen 29 Installeren 30 Bevestigen van de houder voor de afstandsbediening 30 Installeren van de GPS-antenne 31
Aansluitdiagram 32 Laatste controle 35

ITALIANO

Guida allinstallazione 10
Preparativi 36 Precauzioni 37 Procedura di installazione 38 Fissare il portatelecomando 38 Installazione delantenna GPS 39
Collegamenti elettrici 40 Controlle finale 43

ENGLISH

Preparation
Disconnect the lead from the negative () battery terminal.
Caution: Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts.

Installation Precautions

If possible, have the equipment installed by a professional installer. If you should encounter any difficulties, please consult your nearest authorized Panasonic Service Centre. 1. This unit is designed exclusively for use in vehicles having a 12-volt negative ground battery system. 2. Follow the instructions for electrical connection carefully. Failure to do so may result in damage to the unit. 3. Connect the power lead (red) after all other connections are made. 4. Be sure to connect the battery lead (yellow) to the positive (+) terminal of the battery or to the fuse block (BAT) terminal. 5. Insulate all exposed wires to prevent short circuiting. 6. Secure all loose wires after installing the unit. 7. Carefully read the operating and installation instructions of the respective equipment before connecting it to the unit.

Supplied Hardware

No. q w e Item
Tapping Screws with Washers (5 mm x 6 mm) Tapping Screws (5 mm x 16 mm)

Diagram

No. i o !0
Item Remote Control Unit Batteries (R6PU) L-Shaped Bracket

Speed Pulse Cord (5 m)

GPS Antenna

Clip Type Connector

Power Connector
L-Shaped Bracket Cord Clamps (including Double-Sided Tape) Double-Sided Tape

RGB Cord

Remote Control Holder

Cautions

Notes:
It is natural that the unit becomes warm during prolonged use. The unit may not function properly if installed in a location where it is exposed to high temperature such as in the trunk. Preferably install it in the driver's compartment. Install the main unit on a firm base inside the driver's compartment, such as on the floor or in the console box. Any changes in its position may cause the position of your vehicle to deviate in the screen. Choose the location for installing the main unit so that it is easy to reach it for inserting and removing the map DVD-ROM and points in a convenient direction. Do not install the main unit on its side or upside down. This may cause malfunctions. Install the main unit in horizontal position. The permissible tilt is within 10 side to side and within 30 front to back.

Within 10

Within 30
Do not install the main unit in locations that tend to get very hot, such as on the dashboard or in the glove compartment. This may cause damage to the unit. To prevent damage, avoid installing the main unit in places where it is exposed to: Direct sunlight Air flow from the air conditioner Heat generated by other equipment

Precautions

We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
Installation Procedure - Navigation System
Note: Disconnect the cable from the negative () battery terminal.
Attach the L-Shaped Brackets !0 on both sides of the unit with the Tapping Screws with Washers q.
Install the unit with Tapping Screws w.
t Power Connector w Tapping Screws
!0 L-Shaped Brackets q Tapping Screws with washers

e q w e

Secure the rear of the unit. a) Check the electrical connections by referring to this operating instructions. b) Insert Power Connector t to the unit.

After installation, reconnect the negative () battery terminal.
Attaching the Remote Control Holder
Attach the double-sided tape !4 to the back of the Remote Control Holder u. i Remote Control Unit
Remove the backing from the double-sided tape, then press the Remote Control Holder u onto the surface where you want to attach it. u Remote Control Holder Put the remote control i in the holder. !4 Double-Sided Tape
Note: Place the Remote Control Holder where it will not interfere with driving.
Installation of GPS Antenna
Install the GPS antenna in the vehicle where the system can receive GPS satellite signals from all directions.
Do not pull on the cord to remove the antenna. Otherwise you might disconnect the cord or scratch the vehicle surface. Wipe the installation surface clean before attaching the antenna.
Installation inside the Vehicle (Dashboard or Rear Tray) (Recommended)
Install the antenna in horizontal position on the dashboard or in the center of the rear tray near the rear window. Lead the antenna cord inside the vehicle.
This end to face the windshield or rear window !2 L-Shaped Bracket
Wipe the installation surface clean before peeling off the backing paper and attaching the bracket. Windshield at least 20 cm GPS antenna

Display unit

Install the antenna at least 20 cm (recommended clearance) away from the monitor and other electronic components as these may reduce the reception sensitivity. Do not bend, cut or otherwise modify the metal bracket (L-shaped). The metal bracket is supplied exclusively for installation inside the vehicle. Use only the supplied metal bracket !2.
Notes: The body shape of some vehicles may interfere with proper signal reception. Some types of window glass may block signal reception. If the reception sensitivity is not satisfactory with the antenna installed inside the vehicle, please consult your nearest authorized Panasonic Service Centre.
Cautions: This product is designed to be used in a car having 12-volt negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. Do not insert the power connector into the unit until the wiring is completed. Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. Your in-vehicle navigation system requires a complex installation procedure to ensure reliable operation. If you experience any operational difficulties, or require a repair, please refer to the original installer or your supplying dealer for assistance.

Connecting the Handbrake Switch
Handbrake Switch Brake Light

Handbrake Switch

Cut here Handbrake lead (5m) !1Clip Type Connector (Blue/yellow) SIDE BRAKE
Connecting the Engine Control Computer Unit

Caution:

Ask the shop where the system was purchased to adjust the vehicle speed signal reception. Engine Control Computer Unit Clamp Type Connector (ECU) Do not Cut (Gray) Do not cut excess length of cord. Bundle it and fasten with tape. Speed Puls lead (0.3m) (Light green) SPEED
e Speed Puls lead (5m) (Light green)
Connecting the Reverse Cord
Check the Backlight !1Clip Type Connector Backlight
* Take it out of the back of the tail lamp mount.

Cut R N N D 2 L

Reverse lead (4m) REVERSE (Violet/white)
Cautions: If noise is generated in proportion to engine revolutions, the earth conductor of the navigation power cord and that of the monitor unit should be connected to the same place of the metallic block of the car body. Take the same action if the brightness of navigation screen is not constant.

t Power Connector

To connect any lead of the power connector to any lead of the vehicle wiring harness, cut off the terminal and use the clamp type connector supplied instead. Do not cut the speed pulse lead or the remote control lead.

Cut here

Illumination lead (4m) ILLUMINATION

iOrange/white j

!1Clip Type Connector
To the power supply for vehicle lighting
Battery lead (5 m) (Yellow)

BATTERY 5A

To the the vehicle battery, continuous +12V DC

Accessory lead (5 m)

Panasonic

To ACC power, +12V DC

Ground lead (2m)

iBlack j

To clearn, bare metallic part of the vehicle chassis
Navi Mute lead (5m) (Orange)

NAVI MUTE

To NAVI Mute/Telephone Mute of audio reciever
For use with Panasonic audio systems provided with NAVI Mute function. For details refer to the operating instructions of your audio system.
Infrared Receiver (option)
This receiver is required to connect a monitor other than Panasonics. Infrared Receiver lead (4 m) RM-DATA (Black) Receiver lead (3 m) (Black/green) Speaker Cord (0.25 m) SPEAKER (Black)

ER POW

Not Used
Make sure the connectors are plugged firmly into all units. Do not install this kit in places where it could be exposed to splash water or the air flow from the air-conditioner, or near the vehicle entrance where it could be stepped on.

I Panasonic Monitor Connection (CQ-VA707N, CY-VM1500EX, CY-VM1200EX, etc.) Remote Control Sensor
Point the remote control of the navigation system at this sensor to operate it.
Panasonic Monitor CQ-VA707
(Not Supplied) y RGB Cord

CN-DV1800EN

RGB-OUT
r GPS Antenna t Power Connector Note: Non-Panasonic Monitor Connection It is required to buy an optional infrared receiver.
Insert the connector obliquely.

Final Check

Make sure to carry out a final check of connections and GPS reception after installation and wiring are complete.

Connection Check

Press SET UP. Select [System Information] and press ENTER.
Select [Wiring Check] and press ENTER.

GPS Check

Select [GPS] and press ENTER.
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan

YEFM292705