From i-ADF From Platen Original Guide
FLS B4 A5 R A4 A4 R A5 A3
i-ADF Tray Original Guides Adjust to the originals width
C Place originals face down on the platen or face up on the i-ADF. C If the original is not positioned properly, a portion of the original may not be copied. C For originals smaller than A5 size, position the original within the A5 area and select A5.
I Commonly Used Functions and Operating Procedures

Full Size

Makes a copy that is the same size as the original

Reduction or Enlargement

Copies the original at a fixed reduction or enlargement ratio

(See page 16)

(See page 18)

I Memory Capacity

If the memory becomes full during original scanning, the message Cannot Complete / Job Exceeds Memory Capacity will be displayed on the LCD. If this occurs, follow the instructions on the LCD. When additional memory is required, consult with an authorised servicing dealer.
C If the fusing temperature drops excessively on the DP-4510/6010 during a multi-copy cycle, there is a remote possibility that the copying speed will be reduced. The copying speed will automatically return to normal when the fusing temperature rises enough to ensure good fusing performance.
P004-005_4510(pb).p7/31/02, 10:44 AM
Operation Chart Touch Panel Display

I Function Categories

B C D E F
Features C Initial Ready to copy screen. C Original Mode, Exposure Control and Paper Tray BASIC MENU selection. C Job selection (Tandem/Remote, Proof Set and etc.). C Reserved Job(s) verification. 2-SIDED/ORIG. \ C 2-Sided, 2 Page, Booklet Copy Mode, Multi-Size COPY Feed and/or SADF function selection. C Electrical Sort Mode and/or optional Finisher SORT/FINISH selection. C Zoom Copy Mode or Creative Features (Book, Edge, ZOOM/EFFECTS Margin, Stamping, Centering, Image Repeat or Inverse Mode) selection. INSERTION/ C Insertion, OHP Interleaving, Overlay or File Edit OVERLAY Mode selection. JOB MEMORY C Job Memory Mode selection.

Tab Name

See Page

27 37, 84, 89, 46 54

Enter the New IP Address by using the Keypad and then touch the OK button. Ex: 123.123.012.002 NOTE: When entering a one or two digit address, add 00 or 0 in front of the numerical address. Then enter the new machine name by using the QWERTY keyboard then touch the OK button. (Up to 15 characters) Ex: DP-6010 SALES Then enter the new key name (up to 15 characters). (By default, the key name will be up to 15 characters of the stations name. If you do not want to change it, touch the OK button.)
P022-023_4510(pb).P8/2/02, 10:39 AM
Basic Menu Tandem/Remote Copy Settings (Deleting)
I To delete the registered machine.
Use the same procedure as the Registration of the selected machine. (See page 22)
Scroll to screen 05/05 and select 22 Delete tandem desti.
Touch the YES button to confirm the deletion.
P024_4510(pb).P8/2/02, 10:39 AM

Basic Menu Job Queue

I Can refer to a job list waiting for printing, delete or change of priority

(only for print job).

I Procedure
Ex. Delete print job. # Touch JOB QUEUE button.
$ Touch PRINT JOB QUEUE button.
% Input password (4-digit) then touch the OK button.
& Select the job(s)* you wish to delete and then touch DELETE button.
( Confirm whether to delete by selecting YES or NO.
) Touch CLOSE 2 times to return to the BASIC MENU. If you want to delete more jobs repeat steps & and (.
C The PRINT JOB QUEUE requires the Key Operators Password, however, the COPY JOB QUEUE does not require a password. C The Job Queue selection function is only available when the optional HDD is installed. You can select to delete multiple or all jobs. Priority can be selected for print jobs only.
P025_4510(pb).p7/31/02, 10:44 AM
Basic Menu Completion Notice

I Completion Notice

You or a selected party can be notified with a Job Completion Notice via a pop up screen on your PC when the Copy Job is completed. You must set the Job Completion Notice feature prior to starting the job and set up the Status Monitor. The PC IP Addresses will be automatically displayed into the Address Book on your network (contact your network administrator for detail). C Before using the Completion Notice, install the Panasonic-DMS included with the machine. Then, set the Status Monitor as follows; # Right click the Status Monitor icon. $ Select the Job Completion Notice \ Pop up Display.
Set function and Completion Notice
Number of Copies Press START Pop up screen will be shown on your PC
Touch the COMPLETION NOTICE button.
# Select the desired PC Address. $ Touch the OK button.
C This Completion Notice is available only when connected to the network. C To reset the Completion Notice, press the CANCEL button.

Originals

Full Size A3 A4
Copies Reduction A4/A4 R A4/A4 R

Enlargement

C Multi-Size Feeding function cannot be combined except SADF in another 2-sided/original \ copy function.
P034-035_4510(pb).p7/31/02, 10:44 AM
2-Sided/Original \ Copy SADF Mode
I SADF (Single Sheet Automatic Document Feeder) Function
This mode adds a 5 second delay to allow another original to be placed on the i-ADF. Special originals (like thin paper, etc.) can be fed from the i-ADF Tray and copied continuously using the SADF Mode. This is useful, when copying multiple sets of originals that exceed the maximum capacity of the i-ADF Tray of 70 sheets (80 g/m2). (See the Example below) Before using this feature, the SADF Mode must be enabled in the copier function settings. (See page 67)
Place the Original One at a Time or up to 70 sheets (80 g/m2)
Number of Press Copy # Select Copies START 2-SIDED/ ORIG. \ COPY $ Select SADF Function
Place the next original within 5 sec. of last ejected copy.
(Continued on the next page)
C SADF function cannot be combined with 2 \ 1 and 2 \ 2. (See page 59) C Optional Image Memory or Hard Disk Drive may be required.
Example: To make 5 sets of sorted copies of 100-sheet of originals. (a) Place the first 70 sheets of originals on the i-ADF Tray. (b) Touch the 2-SIDED/ORIG. \ COPY menu and select SADF. (c) Touch the SORT/FINISH menu and select the desired sorting/finishing end result. (d) Press the START key. (e) After scanning the first 70 sheets, you can place the remaining 30 sheets of originals on the i-ADF Tray within 5 second to continue copying without interrupting the cycle. Or if you do nothing the machine will display Another original? / YES or NO. (f) Place the remaining 30 sheets of originals on the tray and select YES. (g) After scanning the remaining 30 sheets, Another original? / YES or NO will display, select NO to start the printing process.
Originals: 70 sheets <1st scan>
1st and 2nd Scanned Data are combined into one job. Originals: Remaining 30 sheets <2nd scan> 5 sets of 100-sheet sorted copies are printed
P036_4510(pb).p7/31/02, 10:44 AM

Sort/Finish

Sort/Finish Button
I When using Sort Mode without optional Finisher

1. Features

Sort Rotate-Sort Rotate-Group

2. Operation

Select SORT/ FINISH mode

(See page 51)

(See page 52)

(See page 53)
C To reset INSERTION/OVERLAY, press the RESET key. C The i-ADF is required for PAGE INSERTION/OVERLAY.
P046-047_4510(pb).p7/31/02, 10:45 AM

Insertion/Overlay Cover

I Cover
Adds cover page(s) to the copies. Original

Blank Paper

Original

Colour Paper

Select Blank/Copy and select PAPER TRAY # Select COVER mode.
Place the Originals Select INSERTION/ (Up to 70; 80 g/m2 paper) OVERLAY mode and select Cover mode
$ Select BLANK/COPY with Front or Front + Back. % Select PAPER TRAY. & Touch the OK button.
Insertion/Overlay Page Insertion

I Page Insertion

Insert paper between the copies. Original Blank Paper Original Copied Paper

Insertion Insertion

Place the Originals (Up to 70)
Select INSERTION/ Select Blank/Copy Input insert OVERLAY mode and select PAPER position and select Page TRAY Insertion mode
# Select PAGE INSERTION mode. $ Select BLANK/COPY. % Select PAPER TRAY. & Touch the OK button.
# Input insert page position with Keypad. (Up to 20) $ Touch the OK button.
P048-049_4510(pb).p7/31/02, 10:45 AM
Insertion/Overlay OHP Interleaving

I OHP Interleaving

Inserts paper between OHP film. Original

Copied Paper

OHP1 OHP(1) OHP2 OHP(2)
Place the OHP (Sheet Bypass)
Select INSERTION/ OVERLAY mode and select OHP Interleaving mode
Select Blank/ Copy and select PAPER TRAY
# Select OHP INTERLEAVING mode. $ Select BLANK/COPY. % Select PAPER TRAY. & Touch the OK button.
C To reset each menu mode, touch the CANCEL button on the touch panel. C Certain types of transparency film may not be compatible and may damage your machine. Consult with an authorised Panasonic dealer for advice regarding non-standard paper types. (Panasonic has tested 3M PP2500 transparency film and found it to be compatible.)
Insertion/Overlay Presentation

I Presentation

Inserts paper between OHP film and make copied sets for hand-outs.

Blank Paper OHP1

OHP(1) OHP2 OHP(2)
Select INSERTION/ OVERLAY mode and select Presentation mode
# Select PRESENTATION mode. $ Select BLANK/COPY. % Select PAPER TRAY. & Touch the OK button.

P050-051_4510(pb).p7/31/02, 10:45 AM
Insertion/Overlay Overlay

I Overlay

Overlays a second image onto the first by using a second original. 1st-page

Select Overlay Mode

Press START After the overlay is copied, confirm whether you want to store it in the machine
Place the Select INSERTION/ Originals OVERLAY Mode (Up to 70)
# Adjust the density (transparency) of the page being produced using the LIGHTER and DARKER buttons. $ Touch the OK button.
# If you DO NOT want to store the overlay image into memory for later use, touch NO. $ If you DO want to store the overlay image into memory for later use, touch YES.
C Do not turn Off the power switch if the file has been stored, otherwise the file will be erased. C Only A4 sized originals can be stored as a file. C When storing the new file, new file will overwrites on the stored file. C A registered file can be erased by File Edit mode. (See page 52) C When selecting Overlay in 2-sided copy mode, the first page of the original will be copied to 1-sided.
Insertion/Overlay File Edit

I File Edit

There are three File Edit available in the Form Overlay function. Register: To Add a new file Erase: To Erase a registered file Title Edit: To Change the title of a file

File Key

Select File Edit mode and desired function

Press START (Register)

Place the Select INSERTION/ Original OVERLAY Mode (Register)
REGISTER* # Touch each File Key then, touch the REGISTER button. $ Set the registered density. % Press Start. & Touch the OK button to confirm registration. ( Input the file name by using the QWERTY keyboard then touch the OK button. Refer to entering the station name of the Network Scanner. (See page 98)
ERASE # Select the File Key to erase. $ Touch the ERASE button. % Touch the OK button.
FILE NAME EDIT # Select the File Key to edit. $ Touch the FILE NAME EDIT button. % Change the file name by using the QWERTY keyboard then touch the OK button. Refer to entering the station name of the Network Scanner. (See page 98) & Touch the OK button.
Up to 5 image files can be registered. If the selected File Key already contains a registered file image, the new image will over-write the current image. C Function to select the file is only available when the optional Hard Disk Drive (DA-HD60) is installed.

Sleep/Auto Off Mode*

# Automatically enters the Sleep/Auto Off Mode after 90 minutes from the last copy. The copier power will drop and the indicator will light. $ To make copies, press the ENERGY SAVER key.

Interrupt Mode INTERRUPT

C This mode can interrupt other copy jobs while making copies. # Touch the INTERRUPT key, the indicator will light. $ Make another copy job. % Touch the INTERRUPT key again to continue the original job.
C Energy saver time (15 minutes) and Sleep/Auto Off time (90 minutes) can be changed by the key operator. (See page 67) C Sleep Mode and Auto Off Mode can be selected by the key operator. (See page 70) Modes Normal Operation Power Consumption Approximately 240 Wh (6010) Approximately 210 Wh (4510) Approximately 160 Wh (3510) Approximately 180 Wh (6010) Approximately 170 Wh (4510) Approximately 20 Wh Approximately 4 Wh (Approximately 3 Wh, for DP-3510 and except Europe) Warm Up Time N/A Min. 30 sec. recovery (6010/4510) 180 sec. recovery (6010/4510) 30 sec. recovery (3510) 180 sec. recovery (6010/4510) 30 sec. recovery (3510)
Energy Saver Mode Sleep Mode Auto Off Mode
The machine will not go into Sleep Mode when the Weekly Timer is selected.
P056-057_4510(pb).p7/31/02, 10:45 AM
Other Features Skyshot Mode
I Skyshot allows copying a manuscript without generating dark borders even if the platen cover or ADF is opened.
Skyshot mode eliminates dark borders around the originals, and is especially convenient for copying small-sized originals like bank checks or documents with unusual shapes (round, oval, etc.). These documents can be reproduced without generating any unnecessary black areas simply by making a copy with the cover open. Two types of Skyshot modes can be selected; Digital Skyshot Mode : The scanning area (size) is not pre-determined. Manual Skyshot Mode : The scanning area (size) is pre-registered into memory (M1 and M2) in advance. (See page 72)
Place the Original on the platen (Opening the Platen Cover/ADF)
Select the Digital Skyshot Mode
The Digital Skyshot has been 2 modes ( copy or copy ). The default setting of Digital Skyshot Mode is None. Before using this mode, select each setting by using the Function setting. # Press the FUNCTION Key. $ Touch the COPIER SETTINGS button. % Touch the [ button to advance to the 02/04 Display Screen of Copier Settings menu. & Touch the 06 Digital skyshot mode button. ( Select the desired function and touch the OK button. 06 Digital skyshot setting No : None Freeshp (Free shape) : Copy is made with slant. Parallel : Copy is made to parallel. (within 5 degrees)
C An incorrect exposure may occur when there is a black line at the edge of the original or an image which the copier interprets as a black pattern in the skyshot mode. C An incorrect position detection of the original may occur when a strong light shines onto the glass during skyshot mode.

I Digital Skyshot Mode

I Manual Skyshot Mode
When using this function, the custom size should be registered into memory (M1, M2) in advance. C Set 07 Manual Skyshot Mode in Copier Settings first. (See page 53) Platen UpperLeft Corner

Place the Original*

Touch the JOB MEMORY button
Select Custom Size (M1 or M2)
Changing the default M1/M2 size This setting should be carried out by a Key Operator. # Select the COPIER SETTINGS in Function Setting mode. (See page 68) $ Touch the FG buttons to advance to the 04/04 Display Screen of Copier Settings menu. % Touch the 19 Set key operator code button. & Enter the Key Operators ID Code and then press the OK button. ( Touch the FG buttons to advance to the 03/05 Display Screen. ) Select 12 M1, size and 13 M2, size and enter the originals size. * Touch the OK button.
If using i-ADF, place original on the centre position of ADF Tray. The i-ADF tray can be fed only 50 -105 g/m2 plain paper. C When changing the M1 or M2 Size, consult with the key operator. C When using the manual skyshot mode, the M1 and M2 are turned On and other job memory cannot be used. C To reset the manual skyshot mode, press the RESET key.
P058_4510(pb).p7/31/02, 10:45 AM

Combined Function Table

Next Selections 2-SIDED/ORIG. \ COPY SORT/ FINISH ZOOM/ EFFECTS INSERTION/ OVERLAY Others

First Selections

1\2 2\1 2\2 Book \ Page N in 1 Booklet Multi-Size Feeding SADF Sort Shift-Sort Rotate-Sort Staple-Sort Shift-Group Rotate-Group Non-Sort Punch Zoom Auto Zoom Edge Book Margin Stamping Image Repeat Centering Inverse Cover Insertion OHP Interleaving Presentation Overlay Form Overlay Interrupt Proof Copy Tandem Copy Copy Reservation Manual Skyshot Digital Skyshot

2-SIDED/ORIG. \ COPY

1\ 2 2\ 1 2\ 2 Book \ Page N in 1 Booklet Multi-Size Feeding SADF Sort Shift-Sort Rotate-Sort Staple-Sort Shift-Group Rotate-Group Non-Sort Punch Zoom Auto Zoom Edge Book Margin Stamping Image Repeat Centering Inverse Cover Insertion OHP Interleaving Presentation Overlay Form Overlay Interrupt Proof Copy Tandem Copy Manual Skyshot Digital Skyshot
A A A A A A A b b b b b b b b b b b b b b b A b b b b b b b b b b b A A A A A A A A b b b b b b b b b A b b b b A A b b b b b b b b b b A A A A A A A A b b b b b b b b b A b b b b A A b b b b b b b b b A A A A A A A b b b b b b b b b b A b b b A A b b b b b b A A A A A A A b b b b b b b b b b A b b b A A b b b b b b A A A A A A A b b b b b b b b b b A b b b A A b b b b b b b A A A A A A A b b b A A A A A A b A b b A A b b b b b R b b b b b b b b b A b b b b A A b b b b b b b b b b R b b b b b b b b b A b b b b A A b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b A A A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b R b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b A A b b b b b b b b b b b b b b b b b b b b b b b b b b b A A b b b b b b b b b b b b b b b b b b b b b b b b b b A b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b A b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b A b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b A b b b b b b b b b b b b b b b b b b b b b A A A A R A b b b b b b b b b b b b b b b b A R b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b R b b b b b b b b b b b b b b b A A A A A A b b b b A A A b b A b b b b A A b A b A A b b b b b b b b A A A A A A b b b b A A A b b A b b b b A A b b A A A b b b b b A b A A A A A A A A A A A A A b A b A b b b b A A b A A A A b b b b b A A A A A A A A A b b b b A A A A b A b b b b A A b A A A A b b b b b b b b b b b b b b b b b b b A b b b b A A b b b b b A A b b b b b b b b b b b b b b b b b A b b b b A A b b b b b A A b b b A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A R A A A A A b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b R b b b b b b b b b b b b b b b b b b b b b b b b b b b b b A A b b b A A A A A A A A A A A A A A A b A A A A A A A A A A A A A A A A b b b A A b b b b b b b b b b b b b b b b b b b b b b b b A

01 Auto reset time

02 Power save mode timer

03 Sleep/off mode timer

04 Language default
90 (DP-4510/ 6010) 15 (DP-3510) English

05 Special paper tray 1

None Sets the paper drawer for special paper (ex: coloured). C None, Paper Tray 1, Paper Tray 2, Paper Tray 3, Paper Tray 4, Sheet Bypass, LCT Sets the paper drawer for special paper None (ex: coloured). C None, Paper Tray 1, Paper Tray 2, Paper Tray 3, Paper Tray 4, Sheet Bypass, LCT Sets the output bin. C Upper, Bottom Sets the output bin. C Upper, Bottom Sets the output bin. C Upper, Bottom Upper

06 Special paper tray 2

07 Output Bin Copy

08 Output Bin Printer

Bottom

09 Output Bin FAX/E-MAIL

C It is necessary to input the Key Operator ID code before changing items on this page. Only 3 kind of Paper Size (Letter, A4, B5) will be available when selecting Tray 1. AUTO Paper Size can be selected for Tray 2.
Initial Setting Consult with an authorised service dealer 1 min.
Modes 10 Auto paper out rotate
Function Copier will automatically rotate image and print when selected paper tray is empty. C Off, On Beep sound when touching the panel. C Off, Soft, Loud Beep sound when original is set on the Platen. C No, Yes Beep sound when original is set in the ADF. C No, Yes Monitors copy usage of each department. (1) Print usage of each department (2) Print limit of each department (3) ID code of each department C -4 - +4 mm C -4 - +4 mm

Initial Setting Off

11 Beep sound in Touch Panel 12 Original set beep sound 03/Original set beep sound in ADF 14 Dept. counter mode
Soft No Yes Consult with an authorised service dealer 0 mm 0 mm 0 mm Off
15 Fold position (A3/LDG) 16 Fold position (B4) 04/09
17 Fold position (A4/LTR-R) C -4 - +4 mm 19 Language select priority C Off, On
C It is necessary to input the Key Operator ID code before changing items on this page.
P068-069_4510(pb).p7/31/02, 10:49 AM
Modes 20 Date time setting 21 Weekly-timer 22 DHCP default
Function Sets date time registered. C Month, Day, Year, Time Sets the weekly On/Off timer. C Off, On Sets the DHCP.** CNo, Yes Sets user IP address.** C 3 digits 4 Sets the subnet mask.** C 3 digits 4 Sets the gateway address.** C 3 digits 4 Sets the DNS server.** C No, Yes Selects the hard disk format. C Stop, Start Selects the hard disk error check. C Stop, Start

Off Yes

05/TCP/IP address 24 TCP/IP subnet mask 25 TCP/IP default gateway 26 DNS server address 06/Hard disk format 28 Hard disk error check
Not required in copying mode, but needed when installing options for advanced functions (see page 126). When the No. 22 to 26 function is set, turn OFF and ON the Power Switch. C It is necessary to input the Key Operator ID code before changing items on this page.
P068-069_4510(pb).p7/31/02, 10:50 AM
Modes 30 Sleep/Off mode selection 31 General settings print
Function Selects Sleep or Auto Off mode. C Sleep, Auto Off Sets print of general function. C Stop, Start Sets clean the corona wire. C Off, On Indicates the MAC address. Input group ID for address book. C 0 ~ 99

Initial Setting Sleep

32 Corona wire cleaning 33 MAC address 34 Address book group ID
35 Tandem user parameter Input parameter of user machine. 36 Community Name(1) Selects to change the SNMP of Community Name (1).* C Enables read only. Selects to change the SNMP of Community Name (2).* C Enables read/write. Input the device name when necessary.* (For Status Monitor/EtherTalk Machine Name) Input the device location when necessary.* (For Status Monitor) Sets the daylight time. C No, Yes

37 Community Name(2)

38 Device Name 39 Device location 09/Daylight time
C It is necessary to input the Key Operator ID code before changing items on this page. When the No. 36 to 39 function is set, turn OFF and ON the Power Switch.
P070-071_4510(pb).p7/31/02, 10:50 AM
Function Copier Settings for Key Operator
Modes 00 Paper size priority
Function Selects paper size priority C A3, B4, A4, B5, A5, LEDGER, LEGAL, LETTER, INVOICE, 8 13, 8.Selects original setting C Text, T/P (Text/Photo), Photo Selects contrast for Text mode C1 ~ 7 Selects contrast for Text/Photo mode C1 ~ 7 Selects contrast for Photo mode C1 ~ 7 Selects OHP interleaving paper C Blank, Copy Selects page insertion C Blank, Copy Selects cover paper C F, Blank, F, Copy FB, Blank, FB, Copy (F: Front, FB: Front + Back) Enables or disables the use of SADF function. C No, Yes
01 Original mode default 01/Text contrast 03 T/P contrast 04 Photo contrast 06 Interleaving default 07 Page insertion default 02/Cover mode default
T/P 4 Blank Blank F, Blank

09 SADF mode

Modes 10 Maximum copy setting 12 M1, Size
Function Determines whether to limit number of copies (0-99). Input a size in job memory 1 for frequently used size. C X: 5~432/Y: 5~297 mm (See page 54) Input a size in job memory 2 for frequently used size. C X: 5~432/Y: 5~297 mm (See page 54) Selects the task to perform when memory overflow occurs C Print, Cancel Selects the toner save in Text mode. C None, Level 1, Level 2* Selects the toner save in Photo/Text mode. C None, Level 1, Level 2* Selects the toner save in Photo mode. C None, Level 1, Level 2*

IUpper Bin

Rotate 3 2

C Sort by rotating sets

C 4-Hole punch (A3, A4)
ILower Bin Shift Punch Punch and Shift Punch and Staple Staple Sort
C Offset using electronic sorting (A4)
C Offset using C Sort by punching punching and and stapling sets electronic sorting (A4) (A4)
C Sort by stapling sets C Up to 30 sheets (A4) C Paper weight: 64 - 80 g/m2
P088_dp4510(pb).p7/31/02, 10:50 AM
Face-Up Platen Staple Position (ex. $-1)
Place the Select Original SORT/ FINISH mode Select Finisher Mode

Face-Down

In the 4 hole punch mode, A3 size and A4 B size are available.
Select the type of copy group mode into 2-bin finisher and press OK. # SORT Multiple copies are sorted automatically and stacked with shift. $ ROTATE-SORT (Upper bin only) Copied sets are separated by rotation and exited onto tray. % ROTATE-GROUP (Upper bin only) Grouped copies are rotated and exited onto tray. & NON-SORT Copy is stored on the tray. ( PUNCH* Sorted copies are punched and exited onto tray. (Except Rotate-Sort and Rotate-Group modes) ) SHIFT-SORT (Lower bin only) Copied sets are offset and exited onto tray. * STAPLE-SORT (Lower bin only) Sorted copies are stapled and exited onto tray. + SHIFT-GROUP (Lower bin only) Grouped copies are offset and exited onto tray.
C The above sort modes may not work if you are using gray originals, as this may cause a memory overflow. C In such a case, it is recommended either make copies by separate lots (except staple-sort) or install optional Hard Disk Drive (DA-HD60). C If output sheets are curled, or not properly aligned, remove the paper from the paper tray, turn it over, and replace it in the paper tray.
P089_dp4510(pb).P7/31/02, 10:50 AM
4. Replacing the staple cartridge
The message shown on the left appears when the staples run out.

Stapler Cover

Stapler Unit
# Close the stapler cover. $ Return the finisher to the original position. Check the operation. Select the staple-sort mode with control panel and print the desired data.

P098-099_dp4510(pb).P7/31/02, 10:50 AM
Then enter the key name (up to 15 characters). (By default, the key name will be up to 15 characters of the stations name. If you do not want to change it, touch the OK button.) If you want to assign this address into the Favourite section, press YES, otherwise press NO. Note: The Address Book area is reduced by the number of assigned Favourite stations. Select PC* then touch the OK button.
If you select DD, input will be noticed as DD server. (See page 103 ) C If you make a mistake, use I or H to move the cursor beyond the incorrect character, press CLEAR then re-enter the new character. C The Address Book cannot be changed or erased until the communication has finished. To change or erase the settings, wait until finish communication.
Touch the OK button. Do not change the default Port Number without your Network Administrators approval. (Up to 65535, default is 06509) To record another PCs IP Address, repeat steps 3 to 8.
I Editing the Address Book
If you have to change or erase any of the Address Book stations, follow the steps below. To change the settings of an Address Book station
Touch the Scanner Settings button and touch 06 Edit address book.
Select the station you wish to change. Ex: SALES DEPT
Then enter a new IP Address and touch the OK button. Ex: 123.001.056.220 NOTE:When entering one or two digit address, add 00 or 0 before that address.
P100-101_dp4510(pb).P7/31/02, 10:50 AM
Delete the current station name using the Back Space button. Then enter a new stations name. Ex: PANASONIC Delete the current button name using the Back Space button. Then enter a new button name. Ex: PANASONIC If you want to assign this address into the Favourite section, press YES, otherwise press NO.
Then select a new selection, PC or DD.*
*Do not change the default Port Number without your Network Administrators approval. Default: 0650
C If you select DD, the input will be assigned as DD Server. (See page 103) C If you make a mistake, use I or H to move the cursor beyond the incorrect character, press C (CLEAR) key, then re-enter a new character.
To delete an entry from the Address Book

Touch the Function Key.

Touch the Scanner Settings button and touch 07 Delete address.
Enter the station you wish to delete and touch the OK button. Ex: SALES DEPT

Touch YES.

P102-103_dp4510(pb).P7/31/02, 10:50 AM

P127_dp4510(pb).p7/31/02, 10:51 AM
1 \ 2 Copy.. 28 1-Bin Saddle-Stitch Finisher (DA-FS355). 92-\ 1 Copy.. \ 2 Copy.. Bin Finisher (DA-FS600).. 83-Bin Saddle-Stitch Finisher (DA-FS605). 83-in 1 Copy.. Page Copy.. 30 2-Bin Finisher (DA-FS330).. 88-91 2-Sided/Orig. \ Copy Button.. 27 3000-Sheet Tray (LCT).. in 1 Copy.. in 1 Copy.. 31
Edge.. 41 Editing the Address Book. 100-101 ENERGY SAVER Key... 13 Energy Saver Mode.. 56 Exit Tray.. 82 Expansion Board.. 82
File Edit.. 52 Finisher Functions Indication. 14, 15 For Your Safety... 9 Form Overlay.. 53 Full Size... 4 Full Size Copying.. 16 Function.. 60 Function Categories.. 5 FUNCTION Key.. 13
Accessories... 82 ACTIVE LED (GREEN).. 13 Adding a New PCs IP Address.. 98-99 Adding Paper.. 105-106 Address Book... 98-104 ALARM LED (RED).. 13 Auto Zoom Copying.. 40
GENERAL FUNCTIONS. 61 GENERAL FUNCTIONS for Key Operator.. 67-70
Basic Operation.. 4 Before Calling Service. 119-120 Book.. 41 Book \ 2 Copy.. 29 Booklet Copy.. 33
Handling... 10 HDD Unit.. 82
i-ADF (Inverting Automatic Document Feeder). 17 Image Memory... 82 Image Repeat copy.. 45 Insertion/Overlay.. 46 Installation... 11 INTERRUPT Key.. 13 Interrupt Mode.. 56 Inverse copy.. 45
Centering copy... 45 Changing the Paper Size. 76-77 CLEAR Key... 13 Combined Function Table.. 59 Completion Notice... 26 Completion Notice Button.. 14, 15, 26 Concurrent Copying.. 55 Control Panel.. 13 Copier Care.. 120 COPIER SETTINGS.. 62 Copier Settings for Key Operator. 71-73 Copy Icon... 14, 15 Copy Image and Paper Image Indication. 14, 15, 16 COPY Key... 13 Copy Ratio Indication.. 14, 15, 16 Copy Size Indication.. 14, 15 Cover... 47
Job Memory.. 54 Job Queue... 25 Job Queue Button.. 14, 15, 25 Job Settings Button.. 14, 15, 16

Light Copies... 119

Machine/User Error Code Indication (E1-01, U13, etc.). 14, 15, 120 Machine Outline with Tray Selection. 14, 15 Main Power Switch... 4, 15 Manual Exposure Select Buttons (Lighter and Darker). 14, 15, 16 Manual Skyshot Mode.. 58 Margin... 41 Marked Copies.. 120 Memory Capacity.. 4 Multi-Size Feeding... 34
Density Indicator (7 steps).. 14, 15 Department Counter.. 78-79 Digital Skyshot Mode.. 57 Document Scanning.. 97
P128-129_dp4510(pb).P7/31/02, 10:51 AM
N in 1 Copy.. 31 Network Scanner (Option).. 97-104 Network Settings.. 81 Rotate-Sort.. 37
Saddle-Stitch.. 84, 92 SADF (Single Sheet Automatic Document Feeder) Function. 35, 36 SADF/Multi-Size Feed Mode Indication. 14, 15 SCANNER SETTINGS.. 64 Skyshot Mode... 57 Sleep Mode... 56 Sort... 37 Sort/Finish... 37 Specifications... 122 Stamping (Date Stamp).. 43 Stamping (Issue Number Stamping). 44 Stamping (Page Numbering).. 42 Staple-sort... 84, 88, 92 STOP Key... 13 Supplies.. 127 Supplying the Saddle Stitcher Unit with Staples (DA-FS605). 86 System Console.. 82
OHP Interleaving.. 49 Operation Chart.. 4 Options and Supplies.. 126-127 Original Icon.. 14, 15 Original Image Indication. 14, 15, 16 Original Mode Select Button (Text; Text/Photo; Photo). 14, 15, 16 Original Size Indication.. 14, 15 Overlay... 51