Denotes a potential hazard that could result in serious injury or death.
Denotes hazards that could result in minor injury or damage to the unit. L The following symbols are used to classify and describe the type of instructions to be observed. This type of symbol is used to alert users to a specific operating procedure that must be performed carefully. This type of symbol is used to alert users to a specific operating procedure that must not be performed. This type of symbol is used to alert users to a specific operating procedure that must be emphasized in order to operate the unit safely.
Installation Place the unit securely on a stable levelled surface. Serious damage and/or injury may result if the unit falls. To prevent the risk of fire or electrical shock, do not expose this product to rain or any type of moisture.
Detailed operating instructions are on the CD-ROM.
MB261_771E-PFQW2656ZA-QRG-en.book Page 4 Monday, June 25, 2007 3:13 PM
Make sure that the unit is installed in a well ventilated room so as not to increase density of ozone in the air. Since ozone is heavier than air, it is recommended that air at floor level be ventilated. Operating safeguards Unplug this unit from power outlets before cleaning. Do not use liquid or aerosol cleaners. Do not cover slots and openings on the unit. They are provided for ventilation and protection against overheating. Never place the unit near radiators, or in a place where proper ventilation is not provided. Never push any objects through slots in this unit. This may result in the risk of fire or electric shock. Never spill any liquid on the unit. To reduce the risk of electric shock, do not disassemble this unit. Take the unit to an authorised service centre when service is required. Opening or removing covers may expose you to dangerous voltage or other risks. Incorrect reassembly can cause electric shock when the unit is subsequently used. Follow all warnings and instructions marked on this unit. Unplug this unit from power outlets and refer servicing to an authorised service centre when the following conditions occur: L If the mains lead is damaged or frayed. L If liquid has been spilled into the unit. L If the unit has been exposed to rain or water. L If the unit does not work normally by following the operating instructions. Adjust only controls covered by the operating instructions. Improper adjustment may require extensive work by an authorised service centre. L If the unit has been dropped or physically damaged. L If the unit exhibits a distinct change in performance.

Installation and relocation After moving the unit from cold areas to warmer areas, let the unit adjust to the warmer temperature and do not connect the unit for about 30 minutes. If the unit is connected too soon after a sudden climate change, condensation may form inside the unit causing malfunction. Never install telephone wiring during a lightning storm (KX-MB771 only).
Do not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall socket, and do not use (KXMB771 only).
Never install telephone sockets in wet locations unless the socket is specifically designed for wet locations (KX-MB771 only). Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface (KX-MB771 only). Use caution when installing or modifying telephone lines (KX-MB771 only).
MB261_771E-PFQW2656ZA-QRG-en.book Page 5 Monday, June 25, 2007 3:13 PM
When moving the unit, make sure you are using the side grips (1). Note: L During or immediately after printing, the area near the recording paper exit (3) also gets warm. This is normal.
Laser radiation CLASS 1 LASER PRODUCT The printer of this unit utilises a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Toner cartridge Be careful of the following when you handle the toner cartridge: If you ingest any toner, drink several glasses of water to dilute your stomach contents, and seek immediate medical treatment. If any toner comes into contact with your eyes, flush them thoroughly with water, and seek medical treatment. If any toner comes into contact with your skin, wash the area thoroughly with soap and water. If there is skin irritation, seek immediate medical treatment. If you inhale any toner, move to an area with fresh air and consult local medical personnel. The fuser unit (2) gets hot. Do not touch it.
Laser diode properties Laser output : 5 mW max Wavelength : 760 nm 810 nm Emission duration : Continuous

Fuser unit

Important safety instructions
When using this unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, or personal injury. 1. Do not use this unit near water, for example near a bathtub, wash bowl, kitchen sink, etc. 2. During thunderstorms, avoid using telephones except cordless types. There may be a remote risk of an electric shock from lightning (KX-MB771 only). 3. Do not use this unit to report a gas leak, when in the vicinity of the leak (KX-MB771 only).
MB261_771E-PFQW2656ZA-QRG-en.book Page 6 Monday, June 25, 2007 3:13 PM

MB261_771E-PFQW2656ZA-QRG-en.book Page 8 Monday, June 25, 2007 3:13 PM
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse is of the same rating and that it is approved by ASTA or BSI to BS1362. Check for ASTA mark mark or the BSI
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green-and-Yellow: Earth Blue: Neutral Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-ANDYELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with letter L or coloured RED. How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse (and fuse cover).

on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. WARNING: THIS APPLIANCE MUST BE EARTHED.
MB261_771E-PFQW2656ZA-QRG-en.book Page 9 Monday, June 25, 2007 3:13 PM
Operating Instructions (CD-ROM)
1Detailed Instructions (CD-ROM) Operating operating instructions are on the CD-ROM.
Operating instructions in the CDROM
The operating instructions in the CD-ROM consist of the following contents. Adobe Reader is required to view them. L To view or install the operating instructions in the CD-ROM, see page 15.
1. Introduction and Installation
L Information prior to using the unit, for example how to install the toner cartridge and drum unit, and other accessories.

2. Preparation

L Main settings prior to activating the unit, such as Multi-function software information.

3. Printer

L More ways to use the printer, such as printing on special media.

4. Scanner

L More ways to use the scanner, such as saving as a file or sending as an e-mail attachment.

5. Copier

L More ways to use the copier, such as enlargement/reduction, and ways to save on your paper.

6. Fax (KX-MB771 only)

L Convenient ways to send faxes such as using one-touch dial feature and navigator directory, and broadcast transmission. L More ways to receive faxes, and preventing fax reception from undesired callers.
7. Caller ID (KX-MB771 only) 8. Programmable Features 9. Useful Information 10.Help

L Troubleshooting

11.Paper Jams 12.Cleaning 13.General Information

L Specifications

MB261_771E-PFQW2656ZA-QRG-en.book Page 10 Monday, June 25, 2007 3:13 PM

Table of Contents

1. Table of Contents
Table of Contents (Quick Reference Guide)
1. Introduction and Preparation

Accessories

1.1 1.2 1.3 Supplied accessories.. 11 Accessory information.. 11 Extension telephone adaptor for UK (KXMB771 only).. 11 Connections.. 12 Selecting the operation mode (Scan/Copy) (Fax: KX-MB771 only).. 13 Setting the original.. 13 Help function (KX-MB771 only). 14 Adjusting volume (KX-MB771 only). 14 Date and time (KX-MB771 only). 14 Your logo (KX-MB771 only).. 14 Your fax number (KX-MB771 only). 14 Installing Multi-Function Station. 14

Connections and Setup

1.4 1.5

Document Requirements

Volume

1.8 1.9 1.10 1.11 1.12

Initial Programming

2. How to Use

Printer
2.1 2.2 2.3 Printing from Windows applications. 16 Scanning from the unit (Push Scan). 16 Scanning from a computer (Pull Scan). 16 Making a copy.. 16 Sending a fax manually (KX-MB771 only). 17 Receiving a fax automatically Auto answer ON (KX-MB771 only).. 17 Cancelling the operations.. 17

Scanner

2.4 2.5 2.6
Sending Faxes Receiving Faxes

Useful Information

3. Help

Error Messages

3.1 Error messages Display.. 18

4. General Information

Condition of guarantee
4.1 Condition of guarantee.. 20
MB261_771E-PFQW2656ZA-QRG-en.book Page 11 Monday, June 25, 2007 3:13 PM
Accessories 1Detailed operating instructions 1 Introduction and Preparation are on the CD-ROM.

1.1 Supplied accessories

1 Mains lead (PFJA03A008Y)*CD-ROM (PFJKMB271Z)*1
1.2 Accessory information
To ensure that the unit operates properly, we recommend the use of a Panasonic toner cartridge and drum unit.
1.2.1 Sales and Support Information
Customer Care Centre L For customers within the UK: 3878 L For customers within the Republic of Ireland: L Visit our website for product information L E-mail: customer.care@panasonic.co.uk Direct Sales at Panasonic UK L Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am 5:30pm, Friday 9:30am - 5:30pm (Excluding public holidays). L Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk. L Most major credit and debit cards accepted. L All enquires transactions and distribution facilities are provided directly by Panasonic UK Ltd. L It couldnt be simpler! L Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details. Additional/replacement accessories Replacement toner cartridge*1 L Model No. (Part No.): KX-FAT92X Replacement drum unit*1 L Model No. (Part No.): KX-FAD93X
3 Drum unit (KX-FAD93X)*1
4 Starter toner cartridge*2
5 Quick reference guide (PFQW2656Z)*1
6 Quick installation guide (PFQW2639Z)*1
7 KX-MB771 only Telephone line cord (PQJA87S)*1*3
*1 Approx. 2,000 sheets of A4 size paper can be printed with KX-FAT92X. *1 Part numbers are subject to change without notice. *2 Prints about 500 A4-sized pages with a 5 % image area. *3 For UK. Note: L Save the original carton and packing materials for future shipping and transportation of the unit.
1.3 Extension telephone adaptor for UK (KX-MB771 only)
When using the unit with an external answering machine, please purchase an extension telephone adaptor (e.g., PQJA10058Z) by contacting one of the following: www.panasonic.co.uk Panasonic Customer Care Centre on Telephone number 3878
MB261_771E-PFQW2656ZA-QRG-en.book Page 12 Monday, June 25, 2007 3:13 PM
local Panasonic authorised dealer

1.4 Connections

To EXT socket S b1 a1 E (contact side)
Caution: L The mains lead must remain connected at all times. L Never install telephone wiring during a lightning storm. L When you operate this product, the power outlet should be near the product and easily accessible. L Be sure to use the telephone line cord supplied with this unit (KX-MB771 only). L Do not extend the telephone line cord (KX-MB771 only). 1 Mains lead L Connect to Household Mains Supply (220240 V, 50 Hz). 2 Telephone line cord*1 L Connect to telephone network. 3 [EXT] socket*1 L You can connect an answering machine or an extension telephone. Remove the stopper if attached. 4 Answering machine (not supplied)*1 *1 KX-MB771 only

To telephone line cord of external telephone or telephone answering machine
N. C b1 S E a1 N. C (view: A)
a1, b1: Line S : Shunt E : Earth Recall (This function is not provided on this fax machine.)
2 Extension telephone adaptor (not supplied) 4
* The pictured model is KX-MB771. Important notice for the USB connection L Do NOT connect the USB cable until prompted by the Multi-Function Station (page 15).
MB261_771E-PFQW2656ZA-QRG-en.book Page 13 Monday, June 25, 2007 3:13 PM
Note: L If any other device is connected to the same telephone line, this unit may disturb the network condition of the device (KX-MB771 only). L This unit does not provide a telephone handset. To talk to the other party, please connect an extension telephone (KX-MB771 only).

1.6 Setting the original

1.6.1 Using the scanner glass
1.5 Selecting the operation mode (Scan/Copy) (Fax: KX-MB771 only)
You can select the desired mode by pressing one of the following buttons.
1 Open the document cover (1). 2 Place the document FACE DOWN on the scanner
* The pictured model is KX-MB771. {SCAN}: Select this mode when using the unit as a scanner for the computer. {COPY}: Select this mode when using the unit as a copier. {FAX} (KX-MB771 only): Select this mode when using the unit as a fax machine. glass (2), aligning the top left of the document with the corner to which the m mark points.
3 Close the document cover. 1.6.2 Using the auto document feeder (KXMB771 only)
1 Insert the document (up to 20 pages) FACE UP into
the feeder until a single beep is heard.
2 Adjust the width of the document guides (1) to fit
the actual size of the document.
MB261_771E-PFQW2656ZA-QRG-en.book Page 14 Monday, June 25, 2007 3:13 PM

Help Initial Programming

1.7 Help function (KX-MB771 only)
The unit contains helpful information on the following topics which can be printed for reference purposes, as follows: BASIC SETTINGS FEATURE LIST DIRECTORY FAX RECEIVING COPIER REPORTS CALLER ID
1.9 Date and time (KX-MB771 only)

1 {MENU} i {#}{1}{0}{1} i {SET}

D:|1/M:01/Y:TIME: 00:00

2 Enter the current date/month/year/hour/minute by
selecting 2 digits for each. Press {*} repeatedly to select AM or PM, or 24-hour time entry. Example: 10 August, 2007 10:15 PM (12 hour clock format) 1. Press {1}{0} {0}{8} {0}{7} {1}{0} {1}{5}. D:|0/M:08/Y:TIME: 10:15 2. Press {*} repeatedly to select PM.
1 Press {MENU} repeatedly to display HELP. 2 Press {<} or {>} repeatedly to display the desired

item. i {SET}

3 Press {MENU} to exit.
1.8 Adjusting volume (KX-MB771 only)
Before adjusting volume, set the operation mode to fax mode (page 13). Ringer volume While the unit is idle, press {V} or {^}. L If there are any documents in the document entrance, you cannot adjust the volume. Confirm that there are no documents in the entrance. To turn the ringer OFF Press {V} repeatedly to display RINGER OFF= OK?. i {SET} L The unit will not ring. L To turn the ringer back ON, press {^}. Ringer pattern L You can select one of 3 ringer patterns (feature #161). Monitor volume While using the monitor, press {V} or {^}.
3 {SET} 4 Press {MENU} to exit.
1.10 Your logo (KX-MB771 only)
You can program your logo (name, company name, etc.) so that it appears on the top of each page sent.
1 {MENU} i {#}{1}{0}{2} i {SET}

LOGO=|

2 Enter your logo, up to 30 characters using the dial

keypad. i {SET}

1.11 Your fax number (KX-MB771 only)
You can program your fax number so that it appears on the top of each page sent.
1 {MENU} i {#}{1}{0}{3} i {SET}
2 Enter your fax number, up to 20 digits.
L L L L To enter a +, press {*}. To enter a space, press {#}. To enter a hyphen, press {RECALL}. To erase a number, press {STOP}.
1.12 Installing Multi-Function Station
L Install Multi-Function Station (CD-ROM) before connecting the unit to a computer with USB
MB261_771E-PFQW2656ZA-QRG-en.book Page 15 Monday, June 25, 2007 3:13 PM
cable. If the unit is connected to a computer with USB cable before installing Multi-Function Station, the [Found New Hardware Wizard] dialogue box will appear. Click [Cancel] to close it. L Software features and appearance are subject to change without notice. Warning: L To assure continued emission limit compliance, use only shielded USB cable. To view or install the operating instructions in the CD-ROM 1. Start Windows and insert the supplied CD-ROM into your CD-ROM drive. 2. Click [Operating Instructions], then follow the onscreen instructions to view or install the operating instructions in PDF format. L Adobe Reader is required to view them. Note: L If you install the operating instructions, you can view it anytime from [o] on the Multi-Function Station launcher.

1 Start Windows and exit all other applications.
L For Windows 2000, Windows XP and Windows Vista operating system users, you must be logged in as an administrator in order to install Multi-Function Station.
2 Insert the supplied CD-ROM into your CD-ROM

drive.

3 [Easy installation]
L The installation will start.
4 When the setup program starts, follow the on-screen

instructions.

5 The [Connect Type] dialogue box appears, select
[Connect directly with a USB cable.]. i [Next] L The [Connect Device] dialogue box will appear.
6 Connect the unit with the USB cable (1), then click

[Next].

* The pictured model is KX-MB771.
7 Click [Install], then follow the on-screen
instructions. L The files will be copied to your computer. Important notice If you use Windows XP or Windows Vista, a message may appear after connecting the unit with the USB cable. This is normal and the software will not cause any difficulties with your operating system. You can continue the installation with no problem. The kind of message is displayed: L For Windows XP users The software you are installing for this hardware has not passed Windows Logo testing to verify its compatibility with Windows XP. L For Windows Vista users Would you like to install this device software?
MB261_771E-PFQW2656ZA-QRG-en.book Page 16 Monday, June 25, 2007 3:13 PM
Printer 2Detailed operating instructions are on the CD-ROM. 2 How to Use Copy
2.1 Printing from Windows applications
You can print a file created in a Windows application. For example, to print from WordPad, proceed as follows.

2.4 Making a copy

Illegal copies L It is unlawful to make copies of certain documents. Copying certain documents may be illegal in your country. Penalties of fines and/or imprisonment may be imposed on those found guilty. The following are examples of items that may be illegal to copy in your country. Currency Bank notes and checks Bank and government bonds and securities Passports and identification cards Copyright material or trademarks without the consent of the owner Postage stamps and other negotiable instruments This list is not inclusive and no liability is assumed for either its completeness or accuracy. In case of doubt, contact your legal counsel. Notice: L Install your machine near a supervised area to prevent illegal copies from being made.
1 Open the document you want to print. 2 Select [Print.] from the [File] menu. 3 Select the units name as the active printer.
L If you have changed the name of the unit when installing, select that name from the list.

4 Click [Print] or [OK].

L The unit will start printing.
2.2 Scanning from the unit (Push Scan)

You can easily scan the document by operating the operation panel on the unit.
2.2.1 Scan to Multi-Function Viewer 1 Set the original (page 13). 2 {SCAN} 3 Press {V} or {^} repeatedly to select VIEWER. i
2.4.1 Using the scanner glass 1 If the {COPY} light is OFF, turn it ON by pressing

{COPY}.

4 Press {V} or {^} repeatedly to select USB HOST.

i {SET}

5 If necessary, change the scanning settings (scan
type / resolution / file format / brightness / contrast / scan size). Press {>}, press {V} or {^} repeatedly to select the desired setting. i {SET} i {START}
2 Set the original (page 13). 3 If necessary, change the resolution and contrast
according to the type of document.
4 If necessary, enter the number of copies (up to 99). 5 {START}
L The unit will start copying.
2.3 Scanning from a computer (Pull Scan)
2.3.1 Using Multi-Function scan application
By clicking an application icon, the selected application starts automatically after scanning.
6 After you finish copying, press {STOP} to reset the
settings you set in step 3 and 4.
2.4.2 Using the auto document feeder (KXMB771 only) 1 If the {COPY} light is OFF, turn it ON by pressing
1 Set the original (page 13). 2 Start Multi-Function Station. i [Scan] 3 Click the desired application icon.
MB261_771E-PFQW2656ZA-QRG-en.book Page 17 Monday, June 25, 2007 3:13 PM

Sending Faxes

2.5 Sending a fax manually (KXMB771 only)
2.5.1 Using the scanner glass 1 If the {FAX} light is OFF, turn it ON by pressing

{FAX}.

L When USER STOPPED is not displayed, go to step 2.

2 To cancel printing:

Press {STOP} repeatedly to display STOP PRINTING?. To cancel scanning (KX-MB771 only): Press {STOP} repeatedly to display STOP SCANNING?. To cancel copying: Press {STOP} repeatedly to display STOP COPYING?. To cancel sending or receiving faxes (KX-MB771 only): Press {STOP} repeatedly to display STOP FAX?. To cancel broadcast transmission (KX-MB771 only): Press {STOP} repeatedly to display BROAD CANCELLED?. To cancel fax redialling (KX-MB771 only): Press {STOP} repeatedly to display SEND CANCELLED?.

4 Dial the fax number.

L To send a single page, skip to step 7. L To send multiple pages, go to the next step.
5 Press {QUICK SCAN} to scan the document into

memory.

6 Place the next page on the scanner glass. i

{SET} L To send more pages, repeat this step.
7 {START} 2.5.2 Using the auto document feeder 1 If the {FAX} light is OFF, turn it ON by pressing

3 {SET}

4 {MONITOR} 5 Dial the fax number. i {START}

Receiving Faxes

2.6 Receiving a fax automatically Auto answer ON (KX-MB771 only)
2.6.1 Activating FAX ONLY mode
Press {FAX AUTO ANSWER} repeatedly to display FAX ONLY MODE. How faxes are received When receiving calls, the unit will automatically answer all calls and only receive fax documents.
2.7 Cancelling the operations
You can cancel the current operation from the unit. You can also select the desired operation to cancel.

1 {STOP}

L USER STOPPED is displayed.
MB261_771E-PFQW2656ZA-QRG-en.book Page 18 Monday, June 25, 2007 3:13 PM

3 Help

3.1 Error messages Display
If the unit detects a problem, one or more of the following messages will appear on the display. Display CALL SERVICE CARRIAGE ERROR CHANGE DRUM CHECK DOCUMENT Cause & Solution L There is something wrong with the unit. Contact our service personnel. L There is something wrong with the carriage sensor. Contact our service personnel. L There is something wrong with the drum unit. Replace the drum unit and the toner cartridge. L The document was not fed into the unit properly. Remove the document, then press {STOP} to clear the message. Re-insert the document. If misfeeding occurs frequently, clean the document feeder rollers and try again. L The drum unit is not inserted properly. Re-insert it correctly. L Recording paper is not installed or the paper input tray has run out of paper. Install paper. L Recording paper was not fed into the unit properly. Re-insert the recording paper. L The paper input tray is not installed or is not inserted completely. Insert the paper input tray into the unit. L Recording paper was not fed into the unit properly. Re-insert the recording paper. L The rear cover is open. Close it. L A recording paper jam occurred near the manual input tray. Remove the jammed paper. L There is no space to store new items in navigator directory. Erase unnecessary items. L The drum life is near to an end. Replace the drum unit as soon as possible. L The unit has a document in memory. See the other displayed message instructions to print out the document. L If feature #442 is set to ALWAYS, check the connection between the computer and the unit. L Copying has stopped due to a recording paper jam. See the other displayed message instructions to continue copying. L The inside of the unit is extremely cold and cannot be operated. Use the unit in a warmer area. While the unit cannot be operated, the received documents are temporarily stored into the memory, and will be printed out automatically when the unit warms up. L When performing memory transmission, the document being stored exceeded the memory capacity of the unit. Send the entire document manually. L When making a copy, the document being stored exceeded the memory capacity of the unit. Press {STOP} to clear the message. Divide the document into sections. L There is something wrong with the units modem. Contact our service personnel. L The other partys fax machine is busy or has run out of recording paper. Try again. Detailed operating instructions are on the CD-ROM.

CHECK DRUM CHECK PAPER #1
CHECK PICK UP INPUT TRAY #2 CHECK REAR COVER
DIRECTORY FULL DRUM LIFE LOW REPLACE SOON FAX IN MEMORY

KEEP COPYING LOW TEMP.

MEMORY FULL

MODEM ERROR NO FAX REPLY

MB261_771E-PFQW2656ZA-QRG-en.book Page 19 Monday, June 25, 2007 3:13 PM
Display OUT OF PAPER INPUT TRAY #2 PAPER JAMMED OPEN TOP COVER PC FAIL OR BUSY Cause & Solution L Recording paper is not installed in the manual input tray. Install paper. L A recording paper jam occurred. Remove the jammed paper. L The cable or the computer mains lead is not connected correctly. Check the connections. L The software is not running on the computer. Restart the software and try again. L The unit is warming up. Wait for a while. L The other partys fax machine does not offer the polling function. Check with the other party. L The other partys fax machine is busy or has run out of recording paper. Try again. L The document is jammed. Remove the jammed document. L Attempted to send or copy a document longer than 600 mm using the auto document feeder. Press {STOP} to remove the document. Divide the document into two or more sheets and try again. L The recording paper is installed in the manual input tray when trying to copy, receive faxes or print reports. Remove the recording paper from manual input tray. L The drum units service life is finished. Replace the drum unit immediately. L The memory is full of received documents due to a lack of recording paper or a recording paper jam. Install paper or remove the jammed paper. L If feature #442 is set to ALWAYS, check the connection between the computer and the unit. L The toners service life is finished. Replace the toner cartridge immediately. L The toners service life is near to an end. Replace the toner cartridge as soon as possible. L The top cover is open. Close it. L A transmission error occurred. Try again. L The inside of the unit is cold. Let the unit warm up. Wait for a while. L The fax message was printed on paper which is shorter than A4 size paper. Use the appropriate size paper.
PLEASE WAIT POLLING ERROR REDIAL TIME OUT REMOVE DOCUMENT
REMOVE PAPER IN INPUT TRAY #2 REPLACE DRUM CHANGE SUPPLIES RX MEMORY FULL
TONER EMPTY CHANGE SUPPLIES TONER LOW CHANGE SUPPLIES TOP COVER OPEN TRANSMIT ERROR WARMING UP WRONG PAPER
MB261_771E-PFQW2656ZA-QRG-en.book Page 20 Monday, June 25, 2007 3:13 PM

4 General Information

4.1 Condition of guarantee
1. This machine is supplied with a one year swap out warranty. Please retain your Proof of Purchase and Packaging in the unlikely event that your machine should require attention. For further information please contact us on 3878 for UK or for the Republic of Ireland, in addition you can visit our web site at www.panasonic.co.uk This warranty is in addition to and does not in any way affect any statutory or other right of consumer purchasers. This warranty relates only to product used within Mainland Great Britain, please refer to your dealer warranty information relating to use elsewhere within the United Kingdom and Ireland. This product is designed for use only on the United Kingdom and Irelands Public Switched Telephone Network and should be used only for normal purposes and in accordance with standard operating instructions. You should complete the registration form overleaf and fax it to us with 7 days of purchase; failure to do so may result in delays in providing warranty service. This warranty covers breakdowns due to design or manufacturing faults; it does not apply to damage, however caused, wear or tear, neglect, incorrect adjustment or repair, or to any items of limited natural life. This warranty does not cover consumables, i.e. ink films, film refills, ink cartridges, toner cartridges, drum units, paper and paper loads or any optional accessories which may have been purchased either at the same time as, or subsequent to, the main unit. Such accessories should be returned to the point of purchase if found to be faulty. In the event of a failure, please take the following action; a) Refer to the Help section of your instruction manual in order to identify and possibly correct the problem: b) If the problem is not resolved after referring to the user guide, please contact our customer helpline on 3878 for UK or for the Republic of Ireland In the event the helpline cannot resolve the problem, a like for like exchange fax will be despatched. The helpline operator will give you specific instructions on how the exchange will be executed. Failure to comply with these instructions may result in delay and cost to you. The exchange fax will be delivered in a customised case by courier. It is the customers responsibility to promptly remove the exchange fax and insert the faulty fax in the case provided for collection, to enable the courier to return it to Panasonic. The exchange fax is to be regarded as a like for like exchange under warranty and the balance of the warranty period will transfer to the exchange unit. The purchasers sole and exclusive remedy under this guarantee against Panasonic is for the repair or replacement of the appliance or any defective parts and no other remedy, including, but not limited to; incidental or consequential damage or loss of whatsoever nature shall be available to the purchaser. Where the original fax is found to be faulty as a result of unauthorised repairs or modifications or damage either by accident, misuse or improper installation then Panasonic reserves the right to charge the customer a contribution towards repair costs. If at any time during the guarantee period any parts of the appliance are replaced with parts not supplied or approved by us or of an objective quality, safe and suitable for the appliance, or has been dismantled or repaired by any person not authorised by us, we shall have the right to terminate this guarantee in whole or in part immediately without further notice. This warranty applies to the original purchaser only and is not transferable.

14. The warranty period applicable to this product shall be 12 months from the date of purchase.
Please keep these Operating Instructions with your receipt.
Panasonic Business Systems U.K.
Receipt No. Model No. KX-MB261E/KX-MB771E Date of Purchase Serial No.
MB261_771E-PFQW2656ZA-QRG-en.book Page 21 Monday, June 25, 2007 3:13 PM
MB261_771E-PFQW2656ZA-QRG-en.book Page 22 Monday, June 25, 2007 3:13 PM
MB261_771E-PFQW2656ZA-QRG-en.book Page 23 Monday, June 25, 2007 3:13 PM
MB261_771E-PFQW2656ZA-QRG-en.book Page 28 Monday, June 25, 2007 3:13 PM

: KX-MB261

0682 : KX-MB771

with Fax function

Sales Department: Panasonic Business Systems U.K. Panasonic House, Willoughby Road, Bracknell, Berkshire, RG12 8FP Manufacturer: Panasonic Communications Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Global web site: http://panasonic.net

PFQW2656ZA

CM0607CJ0

KX-MB771 Other Features

KX-MB771 Specifications
General Function Type: Printing Process: Standard Memory Capacity: PC Interface: Scanning System: Caller ID Ready*3: Dialing Mode: Automatic Document Feeder: Paper Tray: Warmup Time: Printer Function PC Interface: Printing Speed: Printing Resolution: Compatible OS*4: Emulation: Paper Handling: Copier Function First Copy Time: Memory Copy Speed: Resolution: Multi-Copy: Enlarge/Reduction Copy: Scanner Function Colour Scanning: Monochrome Scanning: Scanning Resolution: Desktop Laser 32-MB USB 2.0 CIS image sensor, fixed flatbed FSK/DTMF Tone (DTMF)/pulse 20-sheet 250-sheet Approx. 15 seconds (20C) USB 2.0 18-PPM 600 dpi x 600 dpi 98/Me/2000/XP/Vista GDI Letter/A4/Legal Approx. 17 seconds (A4) 18-CPM 600 dpi x 600 dpi Up to 99 copies 25 400% (1% step) Input 48 bits, output 24 bits Input 16 bits, output 8 bits 600 dpi x 300 dpi (ADF) 600 dpi x 1200 dpi (Flatbed) 9600 dpi x 9600 dpi (interpolated) TWAIN 18 ITU T G3 A4/letter 208 mm 33.6 kbps Approx. 4 seconds per page*1,*5 in ECM-MMR memory transmission MH / MR / MMR Standard/fine/super fine/photo 64 levels Max. 150 pages*2 Max. 170 pages*2 Approx. 6.5 W Approx. 65 W Approx. 320 W Approx. 950 W when the fuser lamp turns on AC 220 - 240V, 50/60 Hz 420 mm x 445 mm x 305 mm (16.54" x 17.52" x 12.00") Approx. 13 kg (28.7 lb.)
Versatile, high-performance functions greatly improve document handling efficiency

Multi-Function

4-in-1 multi-Function design dramatically improves business efficiency for every document-related task from faxing and copying to scanning and printing.

Laser Printer

High Speed 18-ppm Laser Print Speed 600 x 600 dpi Resolution Approx. 15 Seconds Warmup Time 250-Sheet Paper Capacity USB 2.0 Interface Works with Microsoft Windows 98/Me/2000/XP/Vista*4

KX-MB771

Flatbed Colour Scanner High Speed 18-ppm Laser Print Speed 600 x 600 dpi Print Resolution Automatic Document Feeder Up to 18-cpm Copy Speed 33.6 kbps Super G3 FAX

Multi-Function Printer

Flatbed Copier
Enhanced 600 dpi Laser Copy Quality Up to 18-cpm Copy Speed Multiple Copies: up to 99 from One Original Enlarge up to 400%, Reduce up to 25% Automatic Document Feeder (20-Sheet)

Colour Scanner

Copier

Printer

Colour Scanning with Flatbed and Automatic Document Feeder 9600 dpi (Interpolated) Scanning Capability 24-bit Colour Output, 8-bit Monochrome Output TWAIN Compatible Scan to PC as PDF, JPEG or TIFF*4 Convert Scanned Pages to Editable Documents with Readiris OCR Software*4 Easy-to-Use Image Viewer*4
Multifunctional Machine that Responds in Full to Today's Office Needs

Scanner

Laser Fax
33.6 kbps Super G3 FAX Resolution: Standard/Fine/Super Fine/Photo Reception Memory with backup, up to 170 pages*1,*2 Transmission Memory, up to 150 pages*1,*2 64-Level Photo Resolution Dual Access with Reserved Transmission Error Correction Mode (ECM) PC Fax*4 Junk Fax Prohibitor
Scanner Driver: Fax Function Compatibility: Paper Handling: Scanning Width: Modem Speed: Transmission Speed: Compression System: Resolution: Halftone: Memory Transmission: Memory Reception: Power Consumption: Sleep: Standby: Copy: Maximum: Power Source: Dimensions (W x D x H): Weight:

USB 2.0 for easy PC connection
2-MB memory unit for storing transmitted/received data Color scanning with both high quality and easy operation Reliable flatbed scanning

Option

KX-FA103 Handset Unit
*1 Based on ITU-T No.1 test chart. *2 Max. 170 pages for out-of-paper reception. Max. 150 pages for memory transmission. *3 Requires subscription to fee-based phone company service. *4 Available when connected to PC running Microsoft Windows 98/Me/2000/XP/Vista. Multi-function software is included. *5 5% coverage. *6 The drum longevity is tested by 20-sheet continued printout intervals. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries
Please refer to additional data for catalog editing on page 3 of the pdf file.

Consumables

KX-FAT92 Toner Cartridge (2,000 pages*1,*5) KX-FAD93 Drum Unit (Max. 6,000 pages*6)
Featuring 600 x 600-dpi laser printer
High Speed, 18-ppm output Dependable 20-sheet automatic document feeder
Global Web Sites: http://www.panasonic.co.jp/global
Design and specifications are subject to change without notice. 0M0707SK-KX-MB771-LT
T E L E C O M M U N I C AT I O N S
The Ultimate Full-Function Business Machine for Enhancing Business Efficiency
Helps to maximize the office's human resources!
The KX-MB771 is equipped with fax, copy, print and scan functions to handle virtually all office document processing needs. Its small footprint efficiently utilizes office space. Each KX-MB771 function features the high performance necessary to maximize office productivity. The new multifunctional KX-MB771 combines high speed, beautiful results and easy operation.

Quality Laser Printing

The laser printer function helps assure high quality reproduction at 600 dpi x 600 dpi resolution in every document and drawing you want to print or copy.

Flatbed Design

In addition to the 20-sheet Automatic Document Feeder, a built-in flatbed allows you to scan, copy, or fax a variety of originals in different shapes or sizes such as magazines, newspapers, ID cards, business cards, etc.

USB 2.0 PC Interface

Beauty Plus Convenience
Bringing new meaning to the word "copy"
The ultimate in detailed reproduction
Optimal document sending and receiving
The KX-MB771 comes standard with a USB 2.0 interface for easy connection to a PC. The bundled Multi-Function Station launcher software allows easy setup and selection of multiple functions.
High-Quality Image Reproduction
A CIS (Color Contact Image Sensor) image sensor makes possible high-speed scanning and high-resolution image reproduction even when the spine is raised slightly above the glass plate.
High-Speed 18-ppm Laser Printing
The KX-MB771 boasts high-speed printing and copying at speeds of up to 18 pages per minute with quick warmup time of 15 seconds.

High-Resolution Copier

With resolution of up to 600 dpi x 600 dpi, sharp, clear copies are assured. Multiple copies of up to 99-sheet are possible.

250-Sheet Paper Tray

Since the standard paper tray can hold up to 250-sheet, you dont have to worry about running out of paper out even during a high-volume print or fax job.

18-cpm Copy Speed

The KX-MB771 delivers high speed copying of up to18 copies per minute, with a warmup time of 15 seconds.
Colour Scanning with Flatbed and ADF
The KX-MB771 allows you to scan documents in colour or black-and-white at a high resolution of 600 dpi x 1200 dpi (with flatbed), or 600 dpi x 300 dpi with an 20-sheet Automatic Document Feeder. (Max. scanning resolution of 9600 dpi x 9600 dpi is available when interpolation is used.)
33.6 kbps High-Speed Fax Modem
The Panasonic laser fax is designed for fast, efficient fax transmission at speeds up to 33.6 kbps (4 seconds per page*1,*5).

Document Memory

This unit can store up to 170*2 pages in its built-in memory. Ideal for broadcasting multi-page documents to multiple locations, this feature also enables out-of-paper reception of up to 150*2 pages.

High-Quality Scanning

The KX-MB771 outputs scanning images with 24-bit colour gradations (48-bit input), or 8-bit black & white gray scales (16-bit input).
Dual Access Operation Image Processing Software
When the Multi-Function Station launcher software is installed on your PC, you can easily access a variety of image processing functions from the graphical menu. With the Viewer (Scan) menu, you can choose Page View, Reduction, Rotate, Duplicate, and Cut and Paste functions. OCR function is also available in 1-byte language designation models. Even while the KX-MB771 is busy sending or receiving a memory-based fax, you can store additional documents to send later.

64-Level Halftone with Digital Image Processing
You can send or copy everything from family photos to company documents with near-original quality, thanks to the clarity and detail of 64 level halftone reproduction.
Additional data for catalog editing
Asia Europe KX-MB778TW 110V 60Hz KX-FAT92X KX-FAD93X KX-MB771E 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771G 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771FR 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771JT 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771SP 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771GR 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771BL 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB771TK 220 240V 50/60Hz KX-FAT92E KX-FAD93E Africa KX-MB773SA 220 240V 50/60Hz KX-FAT92A KX-FAD93A

KX-MB770 series

Model Power Supply Consumables Voltage Herz Toner Drum KX-MB772CX 220 240V 50/60Hz KX-FAT92X KX-FAD93X
KX-MB770 series (w/Handset)
Europe Model w/Handset Power Supply Consumables Voltage Herz Toner Drum KX-MB773PD 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB773FX 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB773EX 220 240V 50/60Hz KX-FAT92E KX-FAD93E KX-MB773RU 220 240V 50/60Hz KX-FAT92A KX-FAD93A CIS KX-MB773UA 220 240V 50/60Hz KX-FAT92A KX-FAD93A