Reviews & Opinions
Independent and trusted. Read before buy Panasonic KX-T206E!

Panasonic KX-T206E

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Panasonic KX-T206E, size: 257 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Panasonic KX-T206EAbout Panasonic KX-T206E
Here you can find all about Panasonic KX-T206E like manual and other informations. For example: review.

Panasonic KX-T206E manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Panasonic KX-T206E please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Panasonic KX-T206E photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 8. Page 1 of 1. Average Rating:
allelopath 3:10pm on Saturday, October 23rd, 2010 
This is not a PC headset, it works great with my AT&T 2-line desk phone. Slips on easily, ear piece is comfortable.
sashenkaa 9:53am on Friday, October 15th, 2010 
i work from home and this is good but not great. i will be upgrading soon is good to start.
sbalneav 11:13am on Saturday, September 25th, 2010 
Just bought 2 more of these. The first broke after 4 years but I like them so much I keep buying. Very clear on both ends. Keeps one ear free. Bought this headset last week. Very happy so far. Clear Reception","Durable
Damaris Trujillo 8:57pm on Wednesday, July 14th, 2010 
Great quality ; low price ; comfortable ; Clear sound ; Loud for the person on the other end :D Maybe too loud.. :P Great quality and price. Works with all my wireless and wired phones that have a 2.5 mm jack Shipping cost
cosmopolite 9:58am on Saturday, June 26th, 2010 
I purchased 6 of these for my technicians to use. Hands free operation in a noisy environment while they walk, climb ladders and use hand tools. Love this headset! It is super comfortable and makes it so easy to be on the phone while getting other things done...
WinXP_Powered 9:40pm on Saturday, June 19th, 2010 
I would not buy a Panasonic KX-TCA60 Headset again. I expect phone headsets to last longer than five months before failing like this one did.
blad 4:13pm on Wednesday, April 28th, 2010 
Excellent headset Great sound quality with my Panasonic cordless phone. I had one before but broke it putting it on over my baseball cap.
repager 3:02am on Thursday, March 25th, 2010 
Don't take the risk of brain tumors - use a corded headset. 4 ft cord","Clear Reception","Durable","Excellent sound quality". Unfortunately, I have 4 slipped disks in my neck for which the pain radiates down my arm and into my hand. Great for high noise area's Clear Reception","Durable","Easy Controls

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

Electronic Modular Switching System
Panasonic Telephone Systems

Panasonic KX-T206E

Panasonic KX-T7206E, KX-T206, KXT206, T206

www.voicesonic.com

Phone: 877-289-2829
Please read this manual before connecting the Electronic Modular Switching System.
ELECTRONIC MODULAR SW ITCHING SYSTEM

MODEL KX-T206E

Thank you for purchasing the Panasonic Model KX-T206E, Electronic Modular Switching System.

System Component

Model No. Service Unit Telephone KX-T206E KX-T7130E KX-T7020E KX-T7050E Description Electronic Modular Switching System Proprietary telephone with display Proprietary telephone Proprietary telephone

Optional Equipment

KX-T20691E DISA/FAX Detect Card KX-T30865E Doorphone
In this Installation Manual, the suffix E of each model number is omitted. A proprietary telephone is abbreviated as PT. A single line telephone is abbreviated as SLT.
APPROVED for connection to telecommunication systems specified in the instructions for use subject to the conditions set out in them.

504100

The serial number of this product may be found on the label affixed to the bottom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid in identification in the event of theft. MODEL NO.: KX-T206E SERIAL NO.: For future reference DATE OF PURCHASE NAME OF DEALER DEALERS ADDRESS

Important Information

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. WARNING : THIS APPLIANCE MUST BE EARTHED. IMPORTANT : The wires in this mains leads are coloured in accordance with the following code: Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. How to replace the fuse : Open the-fuse compartment with a screwdriver and replace the fuse and fuse cover.
This equipment should be used on PSTN lines requiring 2-wire Loop calling unguarded clearing with Loop Disconnect or DTMF address signalling. The equipment must be connected to direct extension lines and a payphone should not be connected as an extension. Operation in Power Failure In the event of a power failure, CO2 is connected to extension 22 automatically. Set the Dialling Mode (Tone or Pulse) of your telephone, according to the CO line. 999 and 112 can be dialled on the apparatus for the purpose of making outgoing calls to the BT emergency (999) and (112) service. Satisfactory performance can not be guaranteed for every allowed combination of host and subsidiary apparatus. 999 and 112 can be dialled on the apparatus after accessing the CO line for the purpose of making outgoing calls to the BT emergency (999) and (112) service. During dialling, this apparatus may tinkle the bells of other telephones using the same line. This is not a fault and we advise you not to call Fault Repair Service. Prevention of access by user. This apparatus is intended to be accessible only to authorized personnel. This apparatus must be installed in a locked room or similar environment, such that user access is prevented. Failure to prevent such user access will invalidate any approval given to this apparatus. Caution: Do not push the PAUSE button more than twice following the initial access digit (or digits). Failure to comply with this requirement may result in unsatisfactory operation. Notice: This PBX should only be used on BT lines on which specific BT services or facilities are provided.

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Precaution

Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps, motors and television. These noise sources can interfere with the performance of the Electronic Modular Switching System. This unit should be kept free of dust, moisture, high temperature (more than 40C/104F) and vibration, and should not be exposed to direct sunlight. Never attempt to insert wires, pins, etc. into the vents or other holes of this unit. If there is any trouble, disconnect the unit from the telephone line. Plug the telephone directly to the telephone line. If the telephone operates properly, do not reconnect the unit to the line until the trouble has been repaired. If the telephone does not operate properly, chances are that the trouble is in the telephone system, and not in the unit. Do not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it with a soft cloth. WARNING THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED SERVICE PERSONNEL. WHEN A FAILURE OCCURS WHICH RESULTS IN THE INTERNAL PARTS BECOMING ACCESSIBLE, DISCONNECT THE POWER SUPPLY CORD IMMEDIATELY AND RETURN THIS UNIT TO YOUR DEALER. DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION PRIOR TO RELOCATING THE EQUIPMENT, AND RECONNECT THE POWER FIRST. THIS UNIT IS EQUIPPED WITH AN EARTHING CONTACT PLUG. FOR SAFETY REASONS THIS PLUG MUST ONLY BE CONNECTED TO AN EARTHING CONTACT SOCKET WHICH HAS BEEN INSTALLED ACCORDING TO REGULATIONS. THE POWER SOCKET WALL OUTLET SHOULD BE LOCATED NEAR THIS EQUIPMENT AND BE EASILY ACCESSIBLE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
73/23/EEC 89/336/EEC 92/31/EEC 93/68/EEC

Table of Contents

Specifications.... Before Installation.... Unpacking.... Name and Location.... Wall Mounting.... Opening Front Cover.... Frame Ground Connection... System Connection Diagram... CO Line Connection.... Extension Connection.... Paralleled Telephone Connection... Installation of Optional Card and Unit... Installation of Lightning Protectors.... Power Failure Transfer.... Starting the System.... General Programming Instructions.... System Programming.... System Speed Dialling Number Set... Dial Type Selection... Outgoing Permitted CO1 Assignment (Day/Night)... Outgoing Permitted CO2 Assignment (Day/Night)... CO1 Ringing Assignment (Day/Night)... CO2 Ringing Assignment (Day/Night)... Doorphone Assignment (Day/Night)... Toll Restriction (TRS) Class Assignment (Day/Night).. TRS Denied Code (CLASS 2, 3).... TRS Denied Code (CLASS 3)... OGM Recording.... OGM Play.... Fax Connection.... CO1 Delayed Ringing Assignment... CO2 Delayed Ringing Assignment... Delayed Ringing Count Selection... TRS Excepted Code.... Door Opener Assignment.... Day/Night Switching Mode.... Day/Night Starting Time.... System Data Clear.... Other programs.... Least Cost Routing (LCR) Programs... Tone / Ring Tone..... Programming Tables.... Templet..... 34 39

Specifications

General Descriptions
1. Capacity. CO line Extension 2 6
2. Control Method.. Stored Program CPU: 8 bits CPU Control ROM: 64 KB, Control RAM: 8 KB 3. Switching Method. Space Division CMOS Crosspoint Switch 4. Power Supplies.. Primary Secondary Power Failure 5. Dialling Outward Internal Mode Conversion 6. Connector.. CO Extension Doorphone 7. EXT Connection.. Cable AC 110240 V, 50/60 Hz Circuit Volt: +5V, +15 V, +30 V CO 2 assigned to extension 22 Dial Pulse 10 PPS Tone Dial Dial Pulse 10 PPS, 20 PPS Tone Dial DP-DTMF, DTMF-DP 4-pin connector 4-pin connector 4-pin connector 1 pair wire (single line telephone) 2 pair wire (proprietary telephone)
8. Intercom paths.. 2 (including the doorphone path)

Characteristics

1. Station Loop Limit.. Proprietary telephone Single line telephone Doorphone 2. Minimum Leak Resistance. 15000 ohms 3. Maximum Number of Station Instruments per line. 1 (proprietary telephone) or 3 (single line telephone) 4. Ring Voltage.. 90 Vrms at 25 Hz depends on Ringing Load 5. Primary Power. AC 110240 V, 50/60 Hz, 0.5 A maximum 6. Central Office Loop Limit. 1600 ohms maximum 7. Environmental Requirements. 040C, 10%90% (Humidity) 40 ohms 600 ohms including set 20 ohms

Before Installation

Please read the following notes concerning installation and connection before installing the system.
Safety Installation Instructions
When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines.

Installation Precautions

This set is exclusively made for wall mounting only. Avoid installing in the following places. (Doing so may result in malfunction, noise, or discoloration.) 1. In direct sunlight and hot, cold, or humid places. (Temperature range: 0C-40C/32F-104F) 2. Sulfuric gases produced in areas where there are thermal springs, etc. may damage the equipment or contacts. 3. Places in which shocks or vibrations are frequent or strong. 4. Dusty places, or places where water or oil may come into contact with the unit. 5. Near high-frequency generating devices such as sewing machines or electric welders. 6. On or near computers, telexes, or other office equipment, as well as microwave ovens or air conditioners. (It is preferable not to install in the same room with the above equipment.) 7. Install at least 1.8 m (6 feet) from radios and televisions. (both the main unit and a proprietary telephone) 8. Do not obstruct area around the main unit (for reasons of maintenance and inspection be especially careful to allow space for cooling above and at the sides of the main unit).

Wiring Precautions

Make sure to keep the following instructions when wiring. 1. Do not wire the telephone cable in parallel with an AC power source, computer, telex, etc. If the cables are run near those wires, shield the cables with metal tubing or use shielded cables and ground the shields. 2. If cables are run on the floor, use protectors or the like to protect the wires where they may be stepped on. Avoid wiring under carpets. 3. Avoid using the same power supply outlet for computers, telexes, and other office equipment. Otherwise, the KX-T206s system operation may be interrupted by the induction noise from such equipment. 4. Please use one pair telephone wire for extension connection of (telephone) equipment such as standard telephones, answering machines, etc., except proprietary telephones (KX-T7130, KX-T7020, KX-T7050, etc.). 5. The AC cord must be plugged off during wiring. After all the wirings are completed, plug the AC cord into an AC outlet. 6. Mis-wiring may cause the system to operate improperly. 7. If an extension does not operate properly, disconnect the telephone from the extension line and then connect again, or plug off the AC cord of the system and then on again. 8. The KX-T206 is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. 9. Use twisted pair cable for CO line connection. 10. CO lines should be installed with lightning protectors. For details, see pages 17 and 18.

Unpacking

Main Unit.. one AC Cord. one Screw and Washer. three 4-pin Plug.. eight

Name and Location

Overview of the Main Unit

AC Inlet

Power Indicator
Inside View of the Main Unit

Door Opener Connector

DOOR OPENER
Cable Holders Extension 4-pin Jacks
EXTN. 6 EXTN. 4 EXTN. 2 DPH

EXTN. 5 EXTN. 3 EXTN. 1

SYSTEM

CO 2 CO 1

CO 4-pin Jack Doorphone Jack Ground Terminal

GROUND

Notes Doorphone Jack and Door Opener Connector are at SELV. CO Line 4-pin Jack and Extension 4-pin Jacks are at TNV.

Wall Mounting

1. Place the templet (on page 39) on the wall to mark the three screw positions.

Templet

2. Install the three screws and washers (included) into the wall. 3. Hook the main unit on the screw heads.

Opening Front Cover

1. Loosen the screw. 2. Slide the cover in the direction of the arrow while pressing the marked position.
ELECTRONIC MODULAR SW I TC HING SYSTEM

Frame Ground Connection

ELECTRONIC MODULAR SWITCHING SYSTEM

To Earth

IMPORTANT!!! Connect the frame of the main unit to earth. 10
System Connection Diagram
2 CO Lines to CO1 and CO2
Doorphone KX-T30865 Door Opener
ELECTRONIC MODULAR SWIT CHING SYSTEM

Panasonic

Doorphone 6 Extensions (one pair) (two pair) KX-T7130 (two pair)
Single Line Telephone (one pair)

Pa nas

oni c nas oni

KX-T7050 (two pair)

N O AUT SCA
nic N aso SCA Pan O AUT nic aso Pan
Cordless Phone (one pair) KX-T7020 Telephone Answering Machine with Facsimile

CO Line Connection

Wire Specification
The wire specifications are as follows: Wire Solid wire Diameter of conductor 0.4 0.65mm
Diameter with coating Connection

0.66 1.05mm

Use a 4-pin plug (included) to connect CO lines. A single plug is able to connect two CO lines. Use twisted pair cable. 1. Lift the transparent part. 2. Insert the required telephone wires into the holes of the plug. Then press the transparent part back into the black part. Note: Do not strip the wires. Insert the wires all the way into the plug.

A B A B CO 2

A B A B
To Modular Jacks from the Central Office Note You can use cable holders to fix the wires.

Extension Connection

The wire specifications are as follows: Wire Solid wire Diameter of conductor 0.4 0.65 mm

0.66 1.05 mm

Use a 4-pin plug (included) to connect extension lines. There are 6 plugs to connect extensions to EXTN. 1 through EXTN. 6 jacks. 1. Lift the transparent part. 2. Insert the required telephone wires into the holes of the plug. Then press the transparent part back into the black part. Note: Do not strip the wires. Insert the wires all the way into the plug.
For a proprietary telephone

H A B L

For single line telephones

EXTN. 1

To extensions Notes A facsimile must be connected to EXTN.6 jack if an optional DISA/FAX Detect card (KXT20691) is installed. See page 16 to install the card. System programming is also required. The #12 Fax Connection program should be assigned as ENABLE. See page 25. The #24 Call Incoming Mode Selection program should be assigned as DISA. See page 28. The EXTN.1 through EXTN.6 jacks correspond to extension numbers 21 through 26 respectively. You can use cable holders to fix the wires. 13

Installation of Lightning Protectors

Overview

A lightning protector is a device to be installed on a CO line to prevent a dangerous surge from entering the building and damaging equipment. A dangerous surge can occur if a telephone line comes in contact with a power line. Trouble due to lightning surges have been showing a steady increase with the development of electronic equipment. In many countries, there are regulations requiring the installation of a lightning protector. A lightning strike to a telephone cable which is 10 m above ground can be as high as 200,000 volts. This system should be installed with lightning protectors. In addition, grounding (connection to earth ground) is very important for the protection of the system.

Installation

CO Lightning Protectors CO Main Distribution Frame CO Main Unit EXTN

EXTN SLT Earth

EXTN PT
Earth Terminal Frame Earth

Outside

CO Protectors (Another Building) CO CO Main Main Distribution Unit Frame EXTN EXTN EXTN EXTN Lightning Protector SLT PT (Main Building)

TEL Earth

Notice If you install an extension outside of the main building, the following precautions are recommended: (1) Install the extension wire underground. (2) Use a conduit to protect the wire. Note The lightning protector for an extension is different from that for CO.
Installation of an Earth Rod

Lightning Protector CO

Earth Wire

Main Unit

(1) (2) (3) (4) (5)
Installation location of the earth rod. Near the protector Check obstructions.. None Composition of the earth rod.. Metal Depth of the earth rod.. More than 50 cm Size of the earth wire.. Thickness is greater than 1.6 mm

(Underground)

Earth Rod
Notes The above figures are recommendations only. The length of earth rod and the required depth depend on the composition of the soil. 18

Power Failure Transfer

In the event of a power failure, CO2 is connected to extension 22 automatically. Note The system programmed data is protected by the factory provided lithium battery.

Starting the System

Plug the AC power cord into the system and an AC outlet. The power indicator of the system will light.
General Programming Instructions
Default Setting This system has a default factory setting. If any of the programming needs to be changed, you can change the setting by system programming. You can use any of the following telephones for system programming: Proprietary Telephone (PT): KX-T7130, KX-T7020, KX-T7050 Single Line Telephone (SLT): tone type All telephones (except KX-T7130) do not have display panels, so you cannot check the setting you have made. Therefore, please use KX-T7130 to check the programming. Extensions Used for Programming To Check the Programmed Data System programming can only be performed from extension 21. Use KX-T7130. When you check the assignment, set the MEMORY switch on PT to PROGRAM. Enter # and the program address. You cannot check programs #60, #62, #63, #65, #67, #84 and #85, as they are not displayed on the display panel. To enter the system programming mode:

Required Telephone Set

Before Programming

[Off-hook] 6

After Programming
To exit the system programming mode:

System Programming

System Speed Dialling Number Set

Description

Used to program System Speed Dial numbers. These numbers are available to all extension users. There are 40 numbers from 00 through 39.

Condition

A maximum of 32 digit numbers can be stored. You must store an automatic line access code (9 or 0), or an individual line code (81 or 82) first. The automatic line access code is assigned in #52 CO Line Access Number Selection. If you store a pause, press.
Input Format Explanation Default

[AA] [Phone No.]

Phone number: 32 digits max.
[AA]=Speed dial number: 00 through 39 Not stored

Dial Type Selection

Assigns the Dial Type (tone or pulse) to CO line.

[A]= 1: CO1/ 2: CO2

[A] [B]

[B]= 0: PULSE/ 1: TONE

Both COs 1: TONE
Outgoing Permitted CO1 Assignment (Day/Night)
Determines the extensions which can have access to CO line 1 in both day and night modes. The extension users can make outgoing CO calls if their extensions are assigned as ENABLE.

Input Format Explanation

(for day)

(for night)

[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 0: DISABLE/ 1: ENABLE All extensions 1: ENABLE

Default

Outgoing Permitted CO2 Assignment (Day/Night)
Determines the extensions which can have access to CO line 2 in both day and night modes. The extension users can make outgoing CO calls if their extensions are assigned as ENABLE.
CO1 Ringing Assignment (Day/Night)
Assigns the extensions which will ring when a call from CO line 1 is received in both day and modes.
[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 0: DISABLE (not ring)/ 1: ENABLE (ring) extension 211: ENABLE other extensions 0: DISABLE
CO2 Ringing Assignment (Day/Night)
Assigns the extensions which will ring when a call from CO line 2 is received in both day and modes.
Doorphone Assignment (Day/Night)

Description Condition

Assigns the extensions which will ring when a doorphone call is received and enables to call the doorphone in both day and night modes.

All extensions must be assigned as 0: DISABLE, if you do not connect a doorphone to the system.
[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 0: DISABLE/ 1: ENABLE extension 211: ENABLE other extensions 0: DISABLE
Toll Restriction (TRS) Class Assignment (Day/Night)
Assigns a Toll Restriction Class to each extension in both day and night modes. The Toll Restriction feature can prohibit certain extension users from placing unauthorized toll calls. The following four classes are available: Class CLASS 1 None CLASS 2 Numbers programmed in #08 Denied code (Class 2, 3) CLASS 3 Numbers programmed in #08 Denied code (Class 2, 3) and #09 Denied code (Class 3) CLASS 4 All CO calls Restricted calls
Emergency call numbers 112 and 999 are excepted from toll restriction.
[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 1: CLASS 1/ 2: CLASS 2/ 3: CLASS 3/ 4: CLASS 4 All extensions 1: CLASS 1
TRS Denied Code (CLASS 2, 3)
Allows you to specify the numbers which are toll-restricted for TRS Class 2 and Class 3.
The character can be any number.

[A] [Denied code No.]

Denied code number: 7 digits,
[A]= Code No.: 0 through digit All codes Not stored
TRS Denied Code (CLASS 3)
Allows you to specify the numbers which are toll-restricted for TRS Class 3.

OGM Recording

Used to record an outgoing message for Direct Inward System Access (DISA).
The recording time is a maximum of 16 seconds. If you perform programming with a PT, the message RECORDING will be displayed on its panel. If the DISA/FAX Detect card is not installed, you will hear a reorder tone and the program is finished. Message example: This is AAA company. Please enter 1 for Mr. AA, 2 for Mr. BB. 6 for Ms. FF. Thank you.

Input Format

(Record your message)

OGM Play

Confirms the outgoing message recorded in the OGM Recording program.
If you perform programming with a PT, the message PLAYBACK will be displayed on its panel.

Fax Connection

Allows the system to detect the CNG tone from a facsimile. If it is set to ENABLE, extension 26 will receive fax transmission data.
The optional DISA/FAX Detect card (KX-T20691) should be installed. The #24 Call Incoming Mode Selection program should be assigned as DISA. Extension 26 should be assigned as DISABLE in the #04/#74 CO1 Ringing Assignment (Day/Night), #05/#75 CO2 Ringing Assignment (Day/Night) and #06/#76 Doorphone Assignment (Day/Night) programs.
[A]= 0: DISABLE (not detect)/ 1: ENABLE (detect) 0: DISABLE

CO1 Delayed Ringing Assignment
Assigns delayed ringing to extensions when a call from CO line 1 is received.
The number of delayed rings is assigned by the #15 Delayed Ringing Count Selection program. This feature is not available for the calls sent by the DISA feature.
[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 0: DISABLE (not delayed)/ 1: ENABLE (delayed) All extensions 0: DISABLE
CO2 Delayed Ringing Assignment
Assigns delayed ringing to extensions when a call from CO line 2 is received.
Delayed Ringing Count Selection
Assigns the number of delayed rings that will be sent to the assigned extensions from the CO lines.
[A]= 1: After 1 ring/ 2: After 2 rings/ 3: After 3 rings/ 4: After 4 rings 2: After 2 rings

TRS Excepted Code

Assigns the numbers which are exceptions to the toll restriction. You can store a maximum of 30 codes.

[A] [Excepted code No.]

Excepted code number: 7 digits,
[A]= Code No.: 00 through digits All codes Not stored

Door Opener Assignment

Assigns each extension to have access to door opener or not.
[A]= 1 through 6 (corresponding to extension no. 21 through 26) [B]= 0: DISABLE/ 1: ENABLE

All extensions 1: ENABLE

Day/Night Switching Mode
Assigns automatic or manual day/night mode.
If automatic switching mode is assigned, day/night mode is switched at the time programmed in #71 Day/Night Starting Time.
[A]= 0: Manual/ 1: Automatic 0: Manual

Day/Night Starting Time

Sets the starting time when automatic day/night mode is programmed in the #70 Day/ Night Switching Mode program.

[A] [BB] [CC] [D]

[BB]= Hour: 01-12 [D]=0: AM / 1: PM
[A]= 1: Day start time / 2: Night start time [CC]=Minute: 00-59 Day 9:00 AM

Night5:30 PM

System Data Clear
Allows the system to re-initialize the system-programmed data. The features mentioned in Station Feature Clear are also re-initialized. See page 11 of the User Manual. When all the programmed data is cleared, the system will restart with the default setting.

Other Programs

Host PBX Access Code Assignment
Assigns a Host PBX access code to make an outside call, if the system is installed behind the host PBX. A pause is automatically inserted after the access code and the toll restriction feature applies to the number after the code. Input Format: #21 [A] [code] # [A]=1: CO1/ 2: CO2 [code] = 2 digits max. (Default : Not stored) Sets the time to send the flash signal to each CO line. Input Format: #22 [A] [B] [A]=1: CO1/ 2: CO2 [B]=0: 80 ms/ 1: 100 ms (default)/ 2: 160 ms/ 3: 300 ms/ 4: 600 ms / 5: 900 ms / 6: 1200 ms

Tone Waiting Time After OGM
Sets the time between sending an outgoing message and sending the ringback tone. Input Format: #40 [A] [A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/ 3: 15 SEC Assigns the length of the hold recall timer and transfer recall timer. The hold recall timer is used to alert an extension that a call has been held for an extended period of time. The transfer recall timer is used to alert an extension that a transferred call has not been answered for an extended period of time. Input Format: #50 [A] [A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/ 3: 3 MIN/ 4: 4 MIN/ 5: DISABLE Assigns the method to put a call on hold with SLTs. Input Format: #51 [A] [A]=1: MODE 1 (hooking) (default) 2: MODE 2 (hooking and dial 6) Selects the automatic line access number. Input Format: #52 [A] [A]=1: 9 (default)/ 2: 0 Assigns whether or not to delete the conference tone. You hear the tone when the conference or the executive busy override feature begins and finishes. Input Format: #53 [A] [A]=0: DISABLE/ 1: ENABLE (default) Selects whether or not to use internal music as the music on hold. Input Format: #54 [A] [A]=1: MODE 1 (NO MUSIC) (default)/ 2: MODE 2 (MUSIC)

Hold Recall Time

Hookswitch Flash Time Assignment

CO Pulse Selection

Assigns to send the pulse to CO line during a conversation with an outside party when the #01 Dial Type Selection program is assigned as Pulse. Input Format: #23 [A] [A]=0: DISABLE/ 1: ENABLE (default) Assigns whether to use the DISA feature or not. This program is available when the DISA/FAX Detect card is installed. Input Format: #24 [A] [B] [A]=1: CO1/ 2: CO2 [B]=0: NORMAL (default)/ 1: DISA Sets the time between one bell signal detection and the next signal from a Central Office. Input Format: #25 [A] [A]=1: 6 SEC/ 2: 3 SEC (default) Assigns the intercom alerting mode to each extension when an intercom call reaches. Input Format: #30 [A] [B] [A]=1 through 6 (corresponding to extension no. 21 through 26) [B]=0: TONE (default)/ 1: VOICE Assigns whether each extension will be connected in parallel with a single line telephone or not. Input Format: #31 [A] [B] [A]=1 through 6 (corresponding to extension no. 21 through 26) [B]=0: DISABLE (default)/ 1: ENABLE

Hold Mode Selection for SLT
Call Incoming Mode Selection
CO Line Access Number Selection

Conference Tone

Bell Off Detection
Intercom Alerting Assignment

Music on Hold Use

Paralleled Telephone Connection
Other Programs (continued)
DISA Ringing Time Assignment
Sets the time to forward a call sent by the DISA feature to other extensions. If the call is not answered by the designated extension within the programmed time, the call is forwarded to extensions which are not assigned as DISABLE in the #04/#74 CO1 Ringing Assignment (Day/Night) and #05/#75 CO2 Ringing Assignment (Day/Night). If DISABLE is selected in this program, the telephone at the designated extension rings for 60 seconds and the call is not forwarded. Input Format: #60 [A] [A]=0: DISABLE / 1: 10 SEC/ 2: 20 SEC (default)/ 3: 35 SEC
Hookswitch Flash Time Range Assignment
Sets the hookswitch flash time range. Input Format: #65 [A] [A]=1: 801000ms / 2: 80150ms 3: 50150ms (default) Assigns the length of the Door Opener time. The door is unlocked for the assigned time. Input Format: #67 [A] [A]= 1: 1 sec/ 2: 2 sec/ 3: 3 sec/ 4: 4 sec/ 5: 5 sec (default) / 6: 6 sec/ 7: 7 sec / 8: 8 sec

Door Opener Access Time

Toll Restriction Code Check
Assigns whether or # is to be checked or not when a user dials them in the Toll Restriction code. Input Format: #62 [A] [A]=0: DISABLE/ 1: ENABLE (default)

CO Indicator Assignment

Assigns whether an incoming CO call indicates or not on the CO button. Also it allows an extension user to answer the call by pressing the CO button when DISABLE is selected in the #04/#74 CO1 Ringing Assignment or the #05/ #75 CO2 Ringing Assignment program. Input Format: #63 [A] [A]=0: DISABLE (The indicator lights red and a user cannot answer the call.) 1: ENABLE (The indicator is flashing and a user can answer the call.) (default)
Note You cannot check the assignments of the programs, #60, #62, #63, #65 and #67 by setting the MEMORY switch to PROGRAM, and entering # and the program address.
Least Cost Routing (LCR) Programs
Least Cost Routing (LCR) is a system programmable feature that automatically selects the least expensive route available at the time a long distance call is made. It is not necessary to dial the access code of the least expensive carrier. You must assign the programs on the next page to activate the LCR feature. The following chart shows the procedure of LCR feature. LCR Sequence chart

[#77] Toll Restriction (TRS) Class Assignment (Night)
[#08] TRS Denied Code [#09] TRS Denied Code [#13] CO 1 Delayed Ringing Assignment (CLASS 2, 3) (CLASS 3) Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
Code Number (7 digits) Code Number (7 digits) 0: DISABLE 1: ENABLE
[#14] CO 2 Delayed Ringing Assignment
0: DISABLE 1: ENABLE Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
[#15] Delayed Ringing Count Selection
1: 1 RING 2: 2 RINGS 3: 3 RINGS 4: 4 RINGS 19 Default Selection

[#16] TRS Excepted Code

Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits)
[#61] Door Opener Assignment
[#70] Day/Night Switching Mode
0: MANUAL 1: AUTO Default Selection
[#71] Day/Night Starting Time
Default Selection 1: DAY 9:00AM 2: NIGHT 5:30PM
[#83] LCR Route Selection Code

Route 1

No. Code (6 digits max.) No. 38 39

Route 2

Code (6 digits max.) No. 38 39

Route 3

Route 4

Code (6 digits max.)

[#88] LCR Route Exceptional Code
No. Code (6 digits max.) No. 18 19
Code (6 digits max.) No. 18 19

Install a screw here

Copy the templet and place it on the wall.

106 mm

See More Panasonic Manuals

Printed in Japan

PSQX1141ZB KW0397KM1097

 

Tags

TX-492RDS Siemens C28 40 D DMA-2500 B-63874HU 05 IP2700 Ls-40 ED VCT-D680RM Designjet 100 Chair Windstar-1998 DGS-3224TGR PDX-1500 RQ-SX33 WM-FS555 Forerunner 101 WFS709TP Touchman 233 Casio 2515 RR-US361 HD 755 SRU5150 87 AWT 2256 FW-C85-02RW Mark II HFC22 08A N676U Dremel 398 HT-C555 Yamaha GW50 DVP-F11 J1453S 970 IS Graph25 TL-WN350G MT400 DV 3300 Rj45 18M HT-X810 P5553SD F-801S NON-stop Girl WS3650 Smac1200 Omnibook 900B T240HD S24AWN-n56 IP 650 LE40R74BD DRA-500AE HTS7540 CU-AV100 HQ5830 CF-VDW07 Se400S Yamaha DX7S Office LE40F86 TX-SR607 Burnout-revenge Fostex E-8 Calculator M2794D-PZ X5150 Subwoofer S-W40S Omniaccess Samsung L310 GR-572TF F3-FOX CI DMC-LZ5 CH-X1500 CTX S700 LC-30HV2E GLC2500L DCR-TRV940 YP-U3 Photo Essentials 3 Prodigy HD403LJ DSK-8 DA-20 PSR-2500 Anachronox ST40 Wind Motif6-motif7-motif8 Ikarus 1200 3YM20 Kdadv5380J-KD-adv5380 Messenger SFP 630 GR-L218STB DI251F TW911P2 TA785G3 HD Neumatico KDL-32EX711 PC-midi SCC-B2303P Review

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101