m)Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
1) When the power supply cord or plug is damaged or frayed. 2) If liquid has been spilled into the product. 3) If the product has been exposed to rain or water.
4) If the product does not operate normally by following the operating instructions.
Adjust only those controls, that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
5) If the product has been dropped or the cabinet has been damaged. 6) If the product exhibits a distinct change in performance. n) Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
o) Do not use the telephone to report a gas leak in the vicinity of the leak.

Attention

Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the Digital Super Hybrid System. This unit should be kept free of dust, moisture, high temperature (more than 40 C) and vibration, and should not be exposed to direct sunlight. Never attempt to insert wires, pins, etc. into the vents or other holes of this unit. If there is any trouble, disconnect the unit from the telephone line. Plug the telephone directly into the telephone line. If the telephone operates properly, do not reconnect the unit to the line until the trouble has been repaired. If the telephone does not operate properly, chances are that the trouble is in the telephone system, and not in the unit. Do not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it with a soft cloth. The ISDN Line Unit (e.g. KX-TD280) is in accordance with the European Telecommunication Standards (ETS). If your telephone company provides an ISDN service which follows the standards other than ETS, some ISDN features in the Features Guide may not work properly. (e.g. Charge Fee Reference, CLIP, COLP, etc.) To use the point-to-multi-point configuration with the KX-TD286, the number on the name plate, which is on the back of the unit, must be or later.

About the other manuals Along with this Installation Manual, the following manuals are available to help you know the available features, programme and use the KX-TD816 / KX-TD1232 system. Features Guide Provides information about the system features. Programming Guide Provides system programming instructions. User Manual Provides operating instructions for the end users using proprietary telephones, single line telephones, consoles or DECT portable stations.

Table of Contents

1 System Outline
1.1 System Highlights.... 14 1.1.1 System Highlights... 14 1.2 Basic System Construction.... 16 1.2.1 Basic System Construction.... 16 1.2.2 System Connection Diagram... 17 1.3 Proprietary Telephones.... 21 1.3.1 Proprietary Telephones.... 21 1.4 Options.... 22 1.4.1 Options.... 22 1.4.2 Expansion Unit Combination... 25 1.5 Specifications.... 27 1.5.1 General Description.... 27 1.5.2 Characteristics... 29 1.5.3 System Capacity.... 30

General Installation

2.1 Before Installation.... 34 2.1.1 Before Installation.... 34 2.2 Installation of the Main Unit... 36 2.2.1 Unpacking.... 36 2.2.2 Location of Interfaces.... 37 2.2.3 Wall Mounting... 39 2.2.4 Frame Ground Connection.... 41 2.2.5 Opening the Front Cover.... 42 2.3 Connection.... 43 2.3.1 Outside Line Connection.... 43 2.3.2 Extension Connection.... 45 2.3.3 Parallelled Telephone Connection... 52 2.3.4 EXtra Device Port (XDP) Connection.. 54 2.3.5 Polarity Sensitive Telephone Connection.. 55 2.3.6 External Pager (Paging Equipment) Connection... 57 2.3.7 External Music Source Connection... 60 2.3.8 Printer and PC Connection.... 63 2.3.9 Installation of Lightning Protectors... 66 2.4 Installation of Optional Cards and Unit... 69 2.4.1 Location of Optional Cards and Units.. 69 2.4.2 4-CO Line Unit Connection.... 74 2.4.3 8-Station Line Unit Connection.... 75 2.4.SLT Line Circuit Unit.... 76 2.4.5 Installing Expansion Unit... 77 2.4.6 Pay Tone Card Installation... 84 2.4.7 DISA Card / Unit and Remote Card / Unit Installation... 87 2.4.8 Doorphone and Door Opener Connection... 94 2.4.9 SLT Message Waiting Lamp Adaptor Unit Connection.. 99 2.4.10 System Connection.... 107
2.4.11 Battery Adaptor Connection...109 2.5 Auxiliary Connection for Power Failure Transfer...112 2.5.1 Auxiliary Connection for Power Failure Transfer...112 2.6 Closing the Front Cover...114 2.6.1 Closing the Front Cover....114 2.7 Starting the System for the First Time...116 2.7.1 Starting the System for the First Time...116 2.8 System Restart...118 2.8.1 System Restart....118 2.9 System Data Clear....119 2.9.1 System Data Clear....119

Cordless Phone Data Terminal (one pair) (one pair) KX-T7000 series analogue proprietary telephones (three pair) (two pair)
DSS console (KX-T7340/KX-T7040)

Voice Processing System

Telephone Answering Machine with Facsimile KX-T7130 analogue proprietary telephone

Proprietary Telephones

The following Panasonic proprietary telephones are available with this system. Proprietary Telephone KX-T7520 KX-T7531 KX-T7533 KX-T7536 KX-T7550 KX-T7425 KX-T7433 KX-T7436 KX-T7450 KX-T7220 KX-T7230 KX-T7235 KX-T7250 KX-T7320 KX-T7330 KX-T7350 KX-T7130 KX-T7020 KX-T7030 KX-T7033 KX-T7050 KX-T7055 KX-TD7500 Description Digital, speakerphone, Jog Dial, 12 Flexible CO Digital, 1-line display, speakerphone, Jog Dial, 12 Flexible CO Digital, 3-line display, speakerphone, Jog Dial, 12 Flexible CO Digital, 6-line display, speakerphone, Jog Dial, 12 Flexible CO Digital, monitor, Jog Dial, 12 Flexible CO Digital, speakerphone, Jog Dial, 24 Flexible CO Digital, 3-line display, speakerphone, Jog Dial, 24 Flexible CO Digital, 6-line display, speakerphone, Jog Dial, 24 Flexible CO Digital, monitor, Jog Dial, 12 Flexible CO Digital, speakerphone, 24 Flexible CO Digital, 2-line display, speakerphone, 24 Flexible CO Digital, 6-line display, speakerphone, 12 Flexible CO Digital, monitor, 6 Flexible CO Speakerphone, 12 Flexible CO 1-line display, speakerphone, 12 Flexible CO Monitor, 12 Flexible CO 1-line display, speakerphone, 12 Flexible CO, 12 PF Speakerphone, 12 Flexible CO, 4 PF 1-line display, speakerphone, 12 Flexible CO, 4 PF 1-line display, speakerphone, 12 Flexible CO, 4 PF Monitor, 12 Flexible CO, 4 PF Monitor, 3 Flexible CO, 4 PF Digital, wireless, 3 Flexible CO
Note Flexible CO : Flexible CO buttton (programmable) PF : Programmable Feature button

Options

Max. Quantity on KXTD1 Max. Quantity on KX-TD1232 Single System System Connection 4 4

Model No.

Model Name

Description

KX-TD170 KX-TD174

8-Station Line Unit

Adds 8 extension lines.
16 SLT Line Circuit Adds 16 extension lines Unit which contain single line telephones. 4-CO Line Unit E&M (TIE) Line Unit Adds 4 outside lines. Adds 4 ports for E&M Line Service.
KX-TD180 KX-TD184 KX-TD280 KX-TD286 KX-TD290
2-ISDN S0 Line Unit Adds 2 ISDN S0 lines. 6-ISDN S0 Line Unit Adds 6 ISDN S0 lines. Primary Rate Interface ISDN Expansion Unit Adds 1 PRI ISDN line.
KX-TD144 KX-TD146 KX-TD142
Cell Station Interface Supports up to two Cell Unit Stations (KX-TD142). Cell Station Interface Supports up to six Cell Unit Stations (KX-TD142). Cell Station
(6 per Cell Station Interface Unit)

After completing all the required inside cabling, including outside lines, extensions, external pagers and external music sources, fasten the cables with the nylon tie (included) as shown.
Programming Guide References
[007] Console Port and Paired Telephone Assignment [109] Expansion Unit Type
Features Guide References

Console

Any single line telephone can be connected in parallel with a proprietary telephone as follows: Method 1: Using a Modular T-Adaptor
Modular T-Adaptor (Panasonic KX-J66 or USOC RJA2X) 2-conductor wiring cord Connect pins T and R.
4-conductor wiring cord For DPT: Connect pins D1 and D2 only. (T and R are not necessary.) For APT: Connect pins T, R, D1 and D2.
Digital / Analogue Proprietary Telephone

Single Line Telephone

Note The KX-TD1232 is illustrated as the main unit. The 6-conductor wiring cord (and the Modular T-Adaptor KX-J36) is required if the proprietary telephone KX-T7130 is to be used for parallel connection for KX-TD1232.
Method 2: For Digital Proprietary Telephones only
<Back of the KX-T7500/KX-T7400 Series DPTs>
To system To single line telephone
4-conductor wiring cord Connect pins T, R, D1 and D2. 2-conductor wiring cord Connect pins T and R.
Note: The above illustration is the KX-T7500. <Back of the KX-T7200 Series DPTs> Single Line Telephone Digital Proprietary Telephone
LCD ADJ PUSH TO EMSS TO TEL
Note The KX-TD1232 is illustrated as the main unit. Not only a single line telephone but a single line device such as an answering machine, a facsimile or a modem (personal computer) etc. can be connected in parallel with a proprietary telephone.

Parallelled Telephone

EXtra Device Port (XDP) Connection
A digital proprietary telephone and a single Line telephone can be connected to the same extension jack yet have different extension numbers (eXtra Device Port feature). System Programming is required for this jack. Method 1

4-conductor wiring cord Connect pins D1 and D2. (T and R are not necessary.)
2-conductor wiring cord Connect pins T and R.
Digital Proprietary Telephone
Note The KX-TD1232 is illustrated as the main unit.
Method 2 Section 2.3.3 Parallelled Telephone Connection, Method 2: for Digital Proprietary Telephone only is also available for XDP connection.

[600] EXtra Device Port

Polarity Sensitive Telephone Connection
If your telephone is polarity sensitive, follow the procedure below:
1. Complete all the required extension wiring. 2. Confirm that dialling can be done from all the extensions using a touch-tone telephone. If
dialling fails, the polarity between the extension and the system must be reversed.

3. Reverse as shown.

Extension Central Office Line Reverse here.
4. Set the Power Switch to "OFF" position. 5. Connect all outside lines. 6. Confirm that dialling can be done on the following extensions using a tone telephone.
KX-TD816 Extension (T, R) of jack 01: Outside line 01 Extension (T, R) of jack 02: Outside line 02 Extension (T, R) of jack 09 and 10 (Extension Expansion Card): Outside line 5 and 6 KX-TD1232 Extension (T, R) of jack 01: Outside line 01 Extension (T, R) of jack 02: Outside line 02 Extension (T, R) of jack 09: Outside line 03 Extension (T, R) of jack 10: Outside line 04 Extensions (T, R) of jacks 17 and 18 (Extension Expansion Card 1): Outside line 09 and 10 (Note: Extensions of jacks 09 and 10 for KX-TD816, and 17 and 18 for KX-TD1232 depend on the Power Failure Transfer connection. For details, refer to Section 2.5.1 Auxiliary Connection for Power Failure Transfer.) If dialling fails, the polarity between the system and the outside line must be reversed.

7. Reverse as shown.

8. Every time an extension telephone is replaced, repeat the above procedure.
External Pager (Paging Equipment) Connection
One external pager (user-supplied) can be connected to the KX-TD816 as illustrated below. Use an RCA connector and shielded cable. Output impedance: 600 Maximum length of the cable AWG 18 22: Under 10 m

16 SLT Line Circuit Unit

To add eight extensions which contain two single line telephones, use the optional 16 SLT Line Circuit Unit (KX-TD174). The unit can support 16 single line telephones per unit. Each single line telephone in the same jack has different extension number so that it can act as completely different extension like an eXtra Device Port feature. Note Installing this unit allows the eXtra Device Port setting to "Enable" automatically in system programming [600]. However, assigning "Disable" makes a single line telephone which is connected to the second jack (Jack xx-2) disable to use. This unit cannot support the proprietary telephone and Voice Mail Integration features. This unit has four DTMF receivers; two receivers in the first eight ports and two receivers in the last eight ports. The Ringing Patterns for all single line telephones which are connected to the system are changed as below;
Incoming call from outside line
Incoming call from extension
Auxiliary Connection for Power Failure Transfer
When there is a power failure, the first two jacks on this unit can be connected to specific CO lines mentioned below. An auxiliary connection is required to implement this feature. For more information about the connection between an extension jack to a CO line, refer to Section 2.5 Auxiliary Connection for Power Failure Transfer.
[109] Expansion Unit Type [600] EXtra Device Port
Installing Expansion Unit
The following procedures can be used to install the optional expansion units. The following steps 1 through 5 and 7 through 10 are the same for all expansion units. Step 6 is different for each unit. The KX-TD1232 is illustrated as the main unit.
1. Loosen the two screws on the cover plate. Insert fingers into the slits to remove the cover

plate.

Slit Slit
Note Any of the cover plates can be removed, as needed.
2. Connect the cabinet cord to the connector in the main unit firmly.
DIGITAL SUPER HYBRID SYSTEM
3. Hook the cabinet on the main unit and slide the cabinet to the left until it is secured.
4. Loosen the outside screw and slide the cover to the right.

Outside screw

5. Secure the inside screw (included) to fix the cabinet to the main unit.

Inside screw

Note Be sure to fix the inside screw to the main unit, or the unit may not work properly.
6. (If a option is to be installed)
If a KX-TD180 is to be installed; Insert the modular plugs of the telephone line cords (4-conductor wiring) into the modular jacks on the unit.

(T1/R1) (T2/R2) TD816: Outside Line 05, Outside Line 06 TD1232: Outside Line 09, Outside Line 10

D IG IT A L S U P E R

TD816: Outside Line 07, Outside Line 08 TD1232: Outside Line 11, Outside Line 12 T2 R1 T1 R2 R: Ring T: Tip View of TEL Jack (Outside Line)

ID S Y S TE

Jack for Power Failure Transfer
To terminal Board or Modular Jacks from the Central Office
Note For details about the jack for Power Failure Transfer, refer to Section 2.5.1 Auxiliary Connection for Power Failure Transfer. If a KX-TD170 and a KX-TD174 is to be installed; Insert the connector into the jack.
D IG IT AL SU PE R H YB R ID SY ST EM
To extensions (TD816 : Jacks 09 16, TD1232 : Jacks or 25 32)
Note For details about the jack for Power Failure Transfer, refer to Section 2.5.1 Auxiliary Connection for Power Failure Transfer. For cable pin numbers to be connected, see "Pin Number Chart" in Section 2.3.2 Extension Connection and "Pin Number Chart for the KX-TD174" on Page 83. For fixing the connector, see "Amphenol 57JE Type (screw-attach-type 50-pin connector) Connection" on Page 81.
7. Tie all of the cords into a bundle. If other cords are exposed in the upper cabinets, tie them
8. Close the cabinet cover and secure the outside screw. 9. Cover the cords with the cord holder (included).

Cord holder

10.Fix the cords to the wall as shown so that the front cover can be opened.
Note If two expansion units are installed, cut the cabinet cover(s) on the lower cabinet(s) to allow the cords from upper cabinet to go down through the cabinet cover(s). To protect the cords, smooth the cut edges.

Cut here

Amphenol 57JE Type (screw-attach-type 50-pin connector) Connection
To fix the Amphenol 57JE type (screw-attach type 50-pin connector) to the 8-Station Line Unit, follow the procedure below.
1. The 50-pin connector (Jack) on the Expansion Unit has two hook-pins. Remove the upper
hook-pin, and take out the screw.
50-pin connector Hook-pins
Note When installing a connector like the type shown below, unscrew the lower hook-pin also. Then drive both accessory screws.

Accessory screw Amphenol 57JE type 50-pin connector

Accessory screw

2. To attach the Amphenol 57JE type (Plug) to the connector, drive the accessory screw into
the upper part. Fasten the accessory wire tie around the lower hook-pin and the Amphenol 57JE type, as shown.

Amphenol 57JE type

Accessory wire tie

57JE type

Hook-pin Accessory wire tie
Pin Number Chart for the KX-TD174
CONN PIN Clip Terminal (KX-A205) No. For KX-TD816 Jack No.9-16 Jack. 09-1 Jack. 10-1 Jack. 11-1 Jack. 12-1 Jack. 13-1 Jack. 14-1 Jack. 15-1 Jack. 16-1 Jack. 09-2 Jack. 10-2 Jack. 11-2 Jack. 12-2 Jack. 13-2 Jack. 14-2 Jack. 15-2 Jack. 16-2 T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R For KX-TD1232 (Expansion 1) Jack No.17-24 Jack. 17-1 Jack. 18-1 Jack. 19-1 Jack. 20-1 Jack. 21-1 Jack. 22-1 Jack. 23-1 Jack. 24-1 Jack. 17-2 Jack. 18-2 Jack. 19-2 Jack. 20-2 Jack. 21-2 Jack. 22-2 Jack. 23-2 Jack. 24-2 T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R For KX-TD1232 (Expansion 2) Jack No.25-32 Jack. 25-1 Jack. 26-1 Jack. 27-1 Jack. 28-1 Jack. 29-1 Jack. 30-1 Jack. 31-1 Jack. 32-1 Jack. 25-2 Jack. 26-2 Jack. 27-2 Jack. 28-2 Jack. 29-2 Jack. 30-2 Jack. 31-2 Jack. 32-2 T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R T R
Pay Tone Card Installation
Installing to the Initial CO Line Card 1. Loosen four screws for KX-TD816 or eight screws for KX-TD1232 to open the inside cover
of the main unit. Note If any cards, units, or cords are installed in the main unit, remove them beforehand.
2. Attach the Pay Tone Card(s) (KX-TD189) to the CO Line Card, with the spacers (Accessary
included). One Pay Tone Card for KX-TD816, and up to two Pay Tone Cards for KX-TD1232 can be installed to the initial CO Line Card.

CO Line Card

Inside Cover

CO03,04 CO01,02

CO Line Card OPJPA D

OP JPH

CO07,08 CO05,06 CO03,04 CO01,02

CO Line Card OPJPA H

3. If you do not cut the wire of the J200 in Pay Tone Card, the detected mode is 16 KHz. If
you cut the wire of the J200 in Pay Tone Card (Open Mode), the detected mode is 12 KHz.
4. After installing the Pay Tone Card, if you hear a noise of the pay-tone signal, cut the option
Jumper Wires, OPJPA through OPJPH, in the CO Card. KX-TD816: OPJPA through OPJPD corresponds to outside line (CO) 01 through 04 respectively. KX-TD1232: OPJPA through OPJPH corresponds to outside line (CO) 01 through 08 respectively. <Example> When you install the Pay Tone Card A, you will detect the pay-tone signal from outside line (CO) 01 through 04, and cut the corresponding option Jumper Wires, if needed. When you install the Pay Tone Card B, you will detect the pay-tone signal from outside line (CO) 05 through 08, and cut the corresponding option Jumper Wires, if needed.

Feature Reference

System Connection

2.4.11

Battery Adaptor Connection
User-supplied car batteries can be used as a backup power supply in the event of a power failure. In case of a power failure, the batteries automatically maintain power to the main unit. The optional Battery Adaptor (KX-A46) is required. The Battery Adaptor should not be exposed to direct sunlight. Keep the adaptor and car batteries away from heating appliances and fire. Place car batteries in a well ventilated place.
When connecting the battery adaptor, keep the following in mind. Check the polarities of batteries and wires. Make sure that you do not short the batteries and wires. To connect the two batteries, use an accessory wire.
1. Assemble the cords and two car batteries (12 VDC each) as shown.
Car batteries Battery Adaptor Red (+) Yellow (-)

12 VDC

Blue (-) Accessory wire Fuse Holder
2. Insert the plug of the battery adaptor into the battery adaptor connector on the main unit.
Connect the ground wire to the ground terminal on the main unit.

Ground Wire

KX-TD816 Plug
Power Switch Ground Terminal

LED Power Switch

3. Turn on the power switch of the battery adaptor.
Wall Mounting 1. Drive the four small accessory screws into the bottom of the unit. 2. Place the metal plates so that the screw heads insert into the slots as shown. 3. Slide the metal plates in the direction of the arrows, and drive the screws. 4. Place the template on the wall to mark two screw positions, and install the big screws into

the wall.

5. Hook the battery adaptor onto the screw heads.
Metal Plates Front Screws (big) Wall Screws (small) Bottom
Mounting on Concrete or Mortar Walls;
At step 4, drill two holes and drive the anchor plugs with a hammer, flush to the wall, and install the big screws into the anchor plugs. Note If the Power LED does not go on, check the main unit, battery adaptor, batteries and wiring connection. After connection of the battery adaptor, keep the power switch on unless when the main unit is turned off. (Batteries will discharge.) To charge the discharged batteries, use a proper charging unit. Power Fuse: (8 A, 32 V) 2 If the Power LED light goes off during a power failure, the power fuse may have been blown. To change the fuse: 1. Turn the power switch off. 2. Turn the fuse holder in the direction of Arrow Arrow A. 3. Change the fuse. 4. Turn the fuse holder in the direction of Arrow Arrow A. 5. Turn the power switch on.

Fuse Holder

while pushing it in the direction of
Back-up Duration: depends on the amp-hour rating of the batteries used. E.g. When using two 12 VDC batteries 20 amp-hour, maintenance-free, car batteries, the power is maintained for about three hours.
Power Failure Transfer connects specific single line telephones to selected outside lines in the event of system power failure, as follows:
Outside Line 01 Extension (T, R) Jack 01 / Outside Line 02 Extension (T, R) Jack 02 / Outside Line 05 Extension (T, R) Jack 09 / Outside Line 06 Extension (T, R) Jack 10 Connections of outside lines 1, 2 and the respective extensions require no auxiliary connection. Outside lines 05 and 06 require auxiliary connection to implement this feature.
Outside Line 01 Extension (T, R) Jack 01 / Outside Line 02 Extension (T, R) Jack 02 / Outside Line 03 Extension (T, R) Jack 09 / Outside Line 04 Extension (T, R) Jack 10 / Outside Line 09 Extension (T, R) Jack 17 / Outside Line 10 Extension (T, R) Jack 18 Connections of outside lines 01 through 04 and the respective extensions require no auxiliary connection. Outside lines 09 and 10 require auxiliary connection to implement this feature. Insert the modular plugs of connection cords (4-conductor wiring) to the modular jacks of 4CO Line Unit and Extension Line Unit 1. (In the case of KX-TD816, one Extension Line Unit is available.)

FT po rts

D IG IT A L S U P E R H
T2 R1 T1 R2 R: Ring T: Tip View of TEL Jack (Outside Line)

FT P A R TS

Note In the event of a power failure, system memory is protected by a factory-provided lithium battery. There is no memory loss except the memories of Camp-on, Saved Number Redial, Last Number Redial, Call Park and Message Waiting. The system changes the current connection to this connection automatically when the power supply stops. If DC power is available from backup batteries if AC power fails, the system does not change the current connection to the above connection. The KX-TD1232 is illustrated as the main unit, and the KX-TD170 and KX-TD180 are illustrated as the expansion units.

Power Failure Transfer

Closing the Front Cover
1. Fasten all the cables and cords with the cord fastener.
Note Be sure to tighten two screws, or the unit may not work properly.

screw screw

be pulled out of the main unit.
Starting the System for the First Time
Set the Power Switch to the "OFF" position. Set the System Clear Switch to the "CLEAR" position. Plug the AC power cord into the system and an AC outlet. Turn the Power Switch on. Press the Reset Button with a pointed tool. (The power indicator will flash.)
6. Slide the System Clear Switch to the "NORMAL" position while the power indicator is
flashing (within approximately 10 seconds). The system will be initialised with default values. The system will also check the outside lines, extensions, and optional cards and units.

One E & M (TIE) Line Unit (KX-TD184) can be installed to either of the two expansion areas on the KX-TD816.
Expansion area 2 Expansion area 1

4 E&M

Note System Programming is required for expansion unit location. <SYS PRG [109]> Default : Area 1 = 4-CO Line Unit Area 2 = 8-Station Line Unit For unit combination, refer to Section 1.4.2 Expansion Unit Combination.
One E & M (TIE) Line Unit (KX-TD184) can be installed to any expansion area on the KXTD1232.
Expansion area 3 Expansion area 2

Expansion area 1

Note System Programming is required for expansion unit location. <SYS PRG [109]> Default : Area 1 = 4-CO Line Unit Area 2 and 3 = 8-Station Line Unit For unit combination, refer to Section 1.4.2 Expansion Unit Combination.
Installing one unit to the system allows four E&M (TIE) lines to be connected to outside lines 05 through 08 for the KX-TD816, or outside lines 09 through 12 or 21 through 24 for the KXTD1232. The KX-TD1232 is illustrated as the main unit.
6. Insert the Amphenol Connector into the jack.

D IG IT A L S U P E

B R ID S Y S T E M
To terminal Board from the E&M (TIE) Line.
Note To fix the connector, refer to Section 2.4.5 Installing Expansion Unit, Amphenol 57JE Type (screw-attach-type 50-pin connector) Connection for KX-TD170. For jack connection, please see "Pin Number Chart" in Section 4.2.3 E&M (TIE) Line Connection.

Programming References

E&M (TIE) Line Connection
Pin Number Chart (E&M Line)
Connect Pin Cable Color ORN-RED ORN-BLK YEL-RED YEL-BLK GRY-RED GRY-BLK WHY-RED WHY-BLK ORN-RED ORN-BLK YEL-RED YEL-BLK GRY-RED GRY-BLK WHY-RED WHY-BLK ORN-RED ORN-BLK YEL-RED YEL-BLK GRY-RED GRY-BLK WHY-RED WHY-BLK ORN-RED ORN-BLK YEL-RED YEL-BLK GRY-RED GRY-BLK WHY-RED WHY-BLK ORN-RED ORN-BLK YEL-RED YEL-BLK GRY-RED GRY-BLK WHY-RED WHY-BLK Clip No. Number of Dots E&M Line T 2-wire or 4-wire - send R T1 4-wire - receive R1 E Lead SG Lead SB Lead M1 Lead SG0 M Lead only for Type 5 T 2-wire or 4-wire - send R T1 4-wire - receive R1 E Lead SG Lead SB Lead M1 Lead SG0 M Lead only for Type 5
T 2-wire or 4-wire - send R T1 4-wire - receive R1 E Lead SG Lead SB Lead M1 Lead SG0 M Lead only for Type 5
Note 21-25, 46-50: Cannot be connected
Cable Pins to be Connected (E&M Line)

E&M Line Wiring

50-pin Connector

Block Terminal

E&M Line 1
Connecting to another KX-TD816/KX-TD1232 system (KX-TD184) 1. 2-wire voice path

KX-TD184

T R E SG M1 SB

Another KX-TD184

Using the Reset Button

If the system does not operate properly, use the Reset Button. (If Master and Slave Systems are in operation by System Connection for KX-TD1232, reset both systems.) Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. Note When the System Clear Switch is set to "NORMAL", pressing the Reset Button causes the following: 1. Camp-on is cleared. 2. Calls on Hold are terminated. 3. Calls on Exclusive Hold are terminated. 4. Calls in progress are terminated. 5. Call Park is cleared. All other data stored in memory is not cleared. When the System Clear Switch is set to the "CLEAR" position, you must press the Reset Button with caution. All data stored in memory will be cleared by the following operation: pressing the Reset Button and setting the System Clear Switch to the "NORMAL" position while the Power Indicator is flashing.
Operation 1. If the system does not operate properly, a) Make sure that the System Clear Switch is set to the "NORMAL" position. b) Press the Reset Button with a pointed tool. 2. If the system still does not operate properly, a) Set the System Clear Switch to the "CLEAR" position. b) Press the Reset Button with a pointed tool. c) Return the System Clear Switch to the "NORMAL" position while the Power Indicator
is flashing (approximately within 10 seconds).
3. If the system still does not work, switch the power off and on again after five minutes. 4. If the system still does not work, a) Switch the power off. b) Set the System Clear Switch to the "CLEAR" position. c) Switch the power on. d) Press the Reset Button with a pointed tool. e) Set the System Clear Switch to the "NORMAL" position while the Power Indicator is
flashing (approximately within 10 seconds).
5. If the system still does not work, switch the power off. If car batteries are connected to the
system, disconnect them, too. Then consult an authorised service person. When the power supply stops, certain extensions are automatically connected straight to specific outside lines:
KX-TD816 Extension (T, R) of jack number 01: Outside line 01 Extension (T, R) of jack number 02: Outside line 02 Extension (T, R) of jack number 09: Outside line 05 Extension (T, R) of jack number 10: Outside line 06 KX-TD1232 Extension (T, R) of jack number 01: Outside line 01 Extension (T, R) of jack number 02: Outside line 02 Extension (T, R) of jack number 09: Outside line 03 Extension (T, R) of jack number 10: Outside line 04 Extension (T, R) of jack number 17: Outside line 09 Extension (T, R) of jack number 18: Outside line 10 Connect single line telephones to the above extension jacks.

Section 7 Index

Numerics 16 SLT Line Circuit Unit (KX-TD174) 22 2-ISDN S0 Line Unit (KX-TD280) 22, 122, 123, 124, 127, 130 4-CO Line Unit (KX-TD180) 22, 69, 70, 74, 86 4-CO Line Unit Connection 74 6-ISDN S0 Line Unit (KX-TD286) 22, 122, 123, 124, 127, 130 8-Station Line Unit (KX-TD170) 22, 69, 70, 75, 79, 81 8-Station Line Unit Connection 75 A AC Adaptor (KX-A277) 24, 156, 157, 161 Add-on Key Module (KX-T7545) 24 Amphenol 57JE Type 81 Auxiliary Connection for Power Failure Transfer 112 B Backup Battery and Adaptor Card (KXA216) 71 Basic System Capacity 14 Basic System Construction 16 Battery Adaptor (KX-A46) 24, 103, 109 Battery Adaptor Connection 109 Before Installation 34 C Cell Station 158 Cell Station (KX-TD142) 22, 148, 154, 155, 156, 157 Cell Station ID Number 167, 169 Cell Station Interface Unit 158 Cell Station Interface Unit (KX-TD144) 22, 148, 154, 155 Cell Station Interface Unit (KX-TD146) 22, 148, 156, 157 Channel Number Switches 170 Characteristics 29, 100 Closing the Front Cover 105, 114 D DECT Portable Station (KX-TD7500) 148 Digital Attendant Console (KX-T7541) 24 Digital DSS Console (KX-T7240) 24 Digital DSS Console (KX-T7440) 24 Digital DSS Console (KX-T7540) 24 DIP-Switch Setting 170 DISA Card (KX-TD191) 23, 72, 87, 92 DISA Card (KX-TD199) 23, 69, 87, 88 DISA Unit (KX-TD190) 22, 69, 87, 90 Display Language 165 Door Opener Connection 94 Doorphone (KX-T30865) 24, 94 Doorphone Card (KX-TD160) 24, 71, 72, 94 Doorphone Connection 94 DSS Console (KX-T7040) 24 DSS Console (KX-T7340) 24 DSS Console for Attendant (KX-T7441) 24 E E & M (TIE) Line Connection 142 E & M (TIE) Line Service 15, 134 E & M (TIE) Line Unit (KX-TD184) 22, 134, 136, 137 Expansion Unit Combination 25 Extension Connection 45 External Music Source Connection 60 External Pager (Paging Equipment) Connection 57 EXtra Device Port (XDP) 14 EXtra Device Port (XDP) Connection 54 F Ferrite Core 160, 161 Frame Ground Connection G Ground

41, 101, 160

41, 101, 127, 128, 160 23, 69,
H High Speed Remote Card (KX-TD197) 72, 87, 88, 93
I Installing Expansion Unit 77 Internal ISDN S0 Line Connection 130 ISDN Line Service 15, 122 ISDN Terminal Equipment (TE) 131, 132 K KX-A216 (Backup Battery and Adaptor Card) 71 KX-A277 (AC Adaptor) 24, 156, 157, 161 KX-A46 (Battery Adaptor) 24, 103, 109 KX-T30865 (Doorphone) 24, 94 KX-T7040 (DSS Console) 24 KX-T7240 (Digital DSS Console) 24 KX-T7340 (DSS Console) 24 KX-T7440 (Digital DSS Console) 24 KX-T7441 (DSS Console for Attendant) 24 KX-T7540 (Digital DSS Console) 24 KX-T7541 (Digital Attendant Console) 24 KX-T7545 (Add-on Key Module) 24 KX-TD142 (Cell Station) 22, 148, 154, 155, 156, 157 KX-TD144 (Cell Station Interface Unit) 22, 148, 154, 155 KX-TD146 (Cell Station Interface Unit) 22, 148, 156, 157 KX-TD160 (Doorphone Card) 24, 71, 72, 94 KX-TD170 (8-Station Line Unit) 22, 69, 70, 75, 79, 81 KX-TD174 (16 SLT Line Circuit Unit) 22 KX-TD180 (4-CO Line Unit) 22, 69, 70, 74, 86 KX-TD184 (E & M (TIE) Line Unit) 22, 134, 136, 137 KX-TD189 (Pay Tone Card) 22, 71, 72 KX-TD190 (DISA Unit) 22, 69, 87, 90