TCD150E(E).book Page 1 Wednesday, May 25, 2005 4:58 PM

Operating Instructions

Digital Cordless Phone

Model No.

KX-TCD150E
Charge the batteries for about 7 hours before initial use.

Table of Contents

Introduction.. 2 Preparation... 3 Making/Answering Calls.. 8 Phonebook.. 9 Useful Telephone Settings.. 10 Caller ID Service... 13 Useful Information.. 14
You must subscribe to Caller ID service to use this feature. Caller ID
Please read these operating instructions before using the unit and save them for future reference.
TCD150E(E).book Page 2 Wednesday, May 25, 2005 4:58 PM

Introduction

Thank you for purchasing a new Panasonic digital cordless phone. For your future reference Attach or keep original receipt to assist with any repair under warranty. Serial No. (found on the bottom of the unit) Date of purchase Name and address of dealer Note: L This equipment is designed for use on the UK and Republic of Ireland analogue telephone network. L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co., Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.doc.panasonic.de Contact: Panasonic Services Europe a Division of Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany

Included accessories

AC adaptor Part No. PQLV19EY (PQLV19E) Telephone line cord Part No. PQJA87S (for UK) Rechargeable batteries AAA (R03) size Part No. HHR-4EPT (Order No. P03P)
Handset cover Part No. PQYNTCD150ER

Operating instructions

Helpline Tel. No.: U.K. 076 R.O.I. 01289 8333
TCD150E(E).book Page 3 Wednesday, May 25, 2005 4:58 PM

Preparation

Important information
General L Use only the AC adaptor included with this product, noted on page 2. L Do not connect the AC adaptor to any AC outlet other than a standard 220240 V AC outlet. L This product is unable to make calls when: The portable handset battery(ies) need recharging or have failed. There is a power failure. The key lock feature is turned on. The call bar feature is turned on (only phone numbers stored in the unit as emergency numbers can be called). L Do not open the base unit or handset other than to replace the battery(ies). L This product should not be used near emergency/intensive care medical equipment and should not be used by people with pacemakers. L Care should be taken that objects do not fall onto, and liquids are not spilled into, the unit. Do not subject this product to excessive smoke, dust, mechanical vibration or shock. L Only the included handset can be used with the base unit. No other handsets can be registered or used. Environment L Do not use this product near water. L This product should be kept away from heat sources such as radiators, cookers, etc. It should also not be placed in rooms where the temperature is less than 5 C or greater than 40 C. L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the unit and is easily accessible.
Warning: L To prevent the risk of electrical shock, do not expose this product to rain or any other type of moisture. L Unplug this unit from power outlets if it emits smoke, an abnormal smell or makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorised service centre. Battery caution L We recommend using the battery(ies) noted on page 2. Use only rechargeable battery(ies). L Do not mix old and new batteries. L Do not dispose of the battery(ies) in a fire, as they may explode. Check local waste management codes for special disposal instructions. L Do not open or mutilate the battery(ies). Released electrolyte from the battery(ies) is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed. L Exercise care when handling the battery(ies). Do not allow conductive materials such as rings, bracelets or keys to touch the battery(ies), otherwise a short circuit may cause the battery(ies) and/or the conductive material to overheat and cause burns. L Charge the battery(ies) in accordance with the information provided in these operating instructions. L Only use the included base unit (or charger) to charge the battery(ies). Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the battery(ies) to swell or explode. Safety caution The ringer tone is reproduced through the handset receiver. To avoid damage to hearing, we recommend you answer

TCD150E(E).book Page 4 Wednesday, May 25, 2005 4:58 PM
incoming calls before holding the phone to your ear. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
TCD150E(E).book Page 5 Wednesday, May 25, 2005 4:58 PM

Connections

Battery installation
Insert the batteries negative (T) terminal first. Close the handset cover.
To telephone network (220240 V, 50 Hz)
Note: L Use only rechargeable batteries (page 2).
Use only the included AC adaptor and telephone line cord.
Note: L Never install telephone wiring during a lightning storm. L Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. L The unit will not work during a power failure. We therefore recommend you also connect a standard telephone to the same telephone line using a T-adaptor. Your Panasonic sales shop can offer you more information about connection possibilities. L To turn the power on, press {ih} for about 1 second. L To turn the power off, press {ih} for about 2 seconds. Location For maximum distance and noise-free operation, place your base unit: Away from electrical appliances such as TVs, radios, personal computers or other phones. In a convenient, high and central location.

Battery charge

Place the handset on the base unit for about 7 hours before initial use. Battery strength Battery icon 074 Battery life Panasonic Ni-MH batteries (700 mAh) Operation While in use (talking) While not in use (standby) Operating time 10 hours max. 120 hours max. Battery strength Fully charged. High Medium Low Needs to be charged.

TCD150E(E).book Page 6 Wednesday, May 25, 2005 4:58 PM

Controls

Handset

A B C D E F G H I

Displays
Icons w 0w4 x k C l 5 Meaning Within range of base unit Out of range, no registration or no power on base unit Paging, intercom mode or accessing base unit Making or answering a call Phonebook mode Setting mode Battery strength Call bar is on (page 10). Direct call is on (page 10). Key lock is on (page 8). Ringer volume is off (page 10). Displayed when you press {#}. Displayed when base unit number is selected for standby mode display (page 10). Displayed when handset number is selected for standby mode display (page 10).

J K L M H

A B C D E F G H I J K L M
Receiver Display {k} (Phonebook) {C} (Talk) Navigator ({e}/{v}/{>}/{<}) {R} (Redial/Pause) {R} (Recall) Charge contacts Microphone {j/OK} (Menu/OK) {ih} (Off/Power) {C} (Clear) {INT} (Intercom)

Base unit

A Charge contacts B {x} (Page)
4 new calls When new calls have been received, the display will show the number of new calls.
TCD150E(E).book Page 7 Wednesday, May 25, 2005 4:58 PM
Symbols used in this manual
These are the symbols that will navigate through these operating instructions. Symbol {j/OK} i Meaning Press {j/OK}. Proceed to the next operation. Press {e} or {v} to select the words in quotations shown on the display.
Setting the date and time
Important: L Confirm that the AC adaptor is connected.
1 {j/OK} 2 SETTING BS ({v}) i {>} i {*} 3 Enter the current hour and minute (24hour time entry). L If you make a mistake, press {C}. Digits will be cleared from the right.
4 {>} 2 times i {*} 2 times 5 Enter the current day, month and year.
L If you make a mistake, press {C}. Digits will be cleared from the right.

Display language

To change the display language

6 {>} i {ih}

{j/OK} SETTING HS ({v}) i {>} DISPLAY OPT i {>} LANGUAGE i {>}
Select the desired language. i {>} i {ih} Note: L If you select a language you cannot read, reset the handset to its default settings: {j/OK} i {v} i {>} i {e} i {>} Enter handset PIN (default: 0000). {v} i {>} i {ih}
TCD150E(E).book Page 8 Wednesday, May 25, 2005 4:58 PM

Making/Answering Calls

Making calls
1 Dial the phone number. i {C} 2 When finished talking, press {ih} or
place the handset on the base unit.
Redialling/storing/editing before calling/erasing 1 {R} i Select the item ({v}). 2 Redialling:
{C} Storing: {>} i SAVE TEL NO i {>} i {j/OK} i Enter the name (9 characters max.; page 9). i {j/OK} Editing before calling: {>} i EDIT CALL NO i {>} i Edit the number. i {C} Erasing: {>} i CLEAR/ALL CLEAR i {>} i YES i {>} i {ih}

Answering calls

1 Press {C} to answer the call.
L You can also answer a call by pressing any dial key from {0} to {9}, {*}, {#}, or {INT}. (Any key answer feature)
2 When finished talking, press {ih} or
place the handset on the base unit. Handset locator
1 Press {x} on the base unit. 2 To stop paging, press {x} on the base
unit or press {C} on the handset.

Key lock

The handset can be locked so that no calls or settings can be made. Incoming calls can be answered, but all other functions are disabled while key lock is on. To turn key lock on, press {j/OK} for about 2 seconds. To turn key lock off, press {j/OK} for about 2 seconds.
To adjust the receiver volume
Press {e} or {v} while on a call.
Pause button (for PBX/long distance service users)
A pause is sometimes required when making calls using a PBX or long distance service. Pressing {R} 1 time creates 1 pause. Press {R} repeatedly to create longer pauses.
Call waiting - {R} button
If a second call is received while in conversation with the first caller, a beep tone will be heard. Press {R} button to switch between callers. This service requires a subscription, consult your service provider for details. Note: L If your unit is connected to a PBX (private branch exchange), consult your PBX dealer for details.
TCD150E(E).book Page 9 Wednesday, May 25, 2005 4:58 PM

Phonebook

Adding entries to the phonebook
The phonebook allows you to make calls without having to dial manually. You can add 20 names and phone numbers to the phonebook.
Making calls/editing/erasing 1 {k} i Display the desired entry ({e}/

2 Making calls:

{C} Editing: {>} i EDIT i {>} i Edit the phone number. i {j/OK} i Edit the name. i {j/OK} Erasing: {>} i CLEAR i {>} i YES i {>} i {ih}
1 {j/OK} 2 times 2 Enter the partys phone number (24 digits

max.). i {j/OK}

3 Enter the partys name (9 characters
max.). i {j/OK} i {ih} Note: L When caller information is received and it matches a phone number stored in the units phonebook, the stored name will be displayed. Character table Keys {1} {2} {3} {4} {5} {6} {7} {8} {9} {0} Characters # A D G J P T [ B E H K Q U ] C F I L O R V Y * 6 S 8 Z 7 , / 1

Hot key (quick dial)

Assigning an entry in the phonebook to a hot key Dial keys {1} to {9} can each be used as a hot key, allowing you to dial a number from the phonebook by simply pressing a dial key.
1 {k} i Display the desired entry ({e}/

{v}). i {j/OK}

2 HOT KEY REG i {>} 3 Select the desired dial key. i {>}
L If the dial key is already assigned as a hot key, the displayed number will flash.

4 YES i {>} i {ih}

Making calls/erasing

W X (Space)

1 Press and hold the desired hot key ({1} to
To edit/correct a mistake
1 Move the cursor to the right of where you
want to correct the number/character ({<}/{>}).
{C} Erasing: {>} 2 times i YES i {>} i {ih}
2 {C} i Enter the correct number/

character.

TCD150E(E).book Page 10 Wednesday, May 25, 2005 4:58 PM
Useful Telephone Settings
Guide to handset settings
To customise the handset:
{j/OK} i SETTING HS i {>} Select the desired item in the handset settings menu ({v}). i {>} Select the desired item in sub-menu ({v}). i {>} Select the desired setting ({v}) or follow the instructions in the Feature column of the chart. L To exit the operation, press {ih}. Sub-menu SET TIME Feature (default setting) Set time alarm. Enter the desired hour and minute (24hour time entry). i {>} Select the desired setting. i {>} Change alarm frequency (OFF). Handset ringer volume (level 6)*1 Ringer type for external calls (RING TYPE 1) Ringer type for internal calls (RING TYPE 1) Ringer type for page (RING TYPE 1) Ringer type for alarm (RING TYPE 1) Keytones on/off (ON) Call waiting tone on/off (ON) Range alarm on/off (OFF) Battery low alarm on/off (ON) Standby mode display (CLOCK) Talk mode display (TALK TIME) Display language (ENGLISH): page 7 Call bar on/off (OFF)*2 Enter handset PIN (default: 0000). Select the desired setting. i {>} Store direct call number.*3 Enter a phone number (24 digits max.). {j/OK} 2 times i ON Direct call on/off (OFF)

Handset settings menu TIME ALARM
SET ALARM RINGER OPT RINGER VOL EXT RINGER INT RINGER PAGING ALARM TONE OPT KEY TONE CALL WAITING RANGE ALARM BATTERY LOW DISPLAY OPT STANDBY MODE TALK MODE LANGUAGE CALL OPT CALL BAR

DIRECT NO

SET DIRECT
TCD150E(E).book Page 11 Wednesday, May 25, 2005 4:58 PM
Handset settings menu OTHER OPT Sub-menu HSPIN CHANGE Feature (default setting) Change handset PIN (0000).*4 Enter the current 4-digit handset PIN. Enter the new 4-digit handset PIN. Enter the new 4-digit handset PIN again. Auto talk on/off (OFF)*5 Reset handset to its default settings. Follow steps 1 and 2. Enter handset PIN (default: 0000). {v} i {>}

AUTO TALK RESET HS

*1 If you set to level 3 to 6 or *6, each ringer will start ringing with lower volume, then gradually increase in volume when receiving a call. Levels 6 and *6 are the highest settings. Their ringing methods are slightly different. *2 Call bar feature prohibits making outside calls. When call bar is turned on, only emergency calls can be made. To store emergency numbers, see page 12. *3 Direct call feature allows you to dial a preset phone number simply by pressing {C}. No dialling is necessary. *4 If you change the PIN, please write down your new PIN as the unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. *5 Auto talk feature allows you to answer calls simply by lifting the handset off the base unit. You do not need to press {C}.
Guide to base unit settings
To customise the base unit:
1 {j/OK} i SETTING BS i {>}
L INPUT CODE is displayed.
2 Enter the desired code number. Follow the instructions in the Feature column of the
chart. L To exit the operation, press {ih}. Code No. {0} {2} {2} Feature (Default setting) Reset base unit to its default settings.*1 Enter base unit PIN (default: 0000). i {>} Base unit ringer volume (Medium) Select the desired setting by pressing {1} for low, {2} for medium, {3} for high or {0} for off. i {>} Change base unit PIN (0000).*2 Enter the current 4-digit base unit PIN. Enter the new 4-digit base unit PIN. Enter the new 4-digit base unit PIN again.
TCD150E(E).book Page 12 Wednesday, May 25, 2005 4:58 PM
Code No. {6} Feature (Default setting) Call restriction*3 Setting call restriction Enter base unit PIN (default: 0000). i {1} i {>} Enter the phone number to be restricted (8 digits max.). L To select a different memory location, press {>} repeatedly and enter a number. {>} Turning on/off call restriction Enter base unit PIN (default: 0000). L Handset number will be displayed. Flashing number indicates call restriction is on; non-flashing number indicates call restriction is off. Press {1} to turn on/off. i {>} Emergency number (112, 999)*4 Enter base unit PIN (default: 0000). i {*} Storing: Enter the emergency number (8 digits max.). L To select a different memory location, press {>} and enter a number. {>} Editing: Display the desired number ({>}). i {C} i Enter the new emergency number. i {>} {*} Time and date: page 7 *1 Only the emergency number setting will not be reset. *2 If you change the PIN, please write down your new PIN as the unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. *3 Call restriction feature restricts the handset from dialling certain phone numbers. You can assign up to 10 phone numbers (memory locations 09) to be restricted. *4 Emergency number feature determines which phone numbers may be dialled while the call bar feature is turned on. A total of 4 emergency numbers (memory locations 14) can be stored.

TCD150E(E).book Page 13 Wednesday, May 25, 2005 4:58 PM

Caller ID Service

Using Caller ID service
Important: L This unit is Caller ID compatible. To use Caller ID features (such as displaying caller phone numbers), you must subscribe to Caller ID service. Consult your service provider for details.
Consult your service provider for details of this service.
Storing/editing/erasing 1 Display the desired entry ({e}/{v}). i

{>}

2 Storing:
SAVE TEL NO i {>} i {j/OK} i Enter the partys name (9 characters max.; page 9). i {j/OK} i {ih} Editing: EDIT CALL NO i {>} Move the cursor to the right of where you want to edit the number ({<}/ {>}). i Edit the phone number. i {C} Erasing: CLEAR/ALL CLEAR i {>} i YES i {>} i {ih}

Caller ID features

Display indications L When new calls have been received, the display will show the number of new calls. Example: 4 new calls have been received.
L Phone numbers of the last 50 different callers will be logged in the caller list. Example:

Voice mail service

Voice mail is an automatic answering service offered by your service provider. If you subscribe to this service, your service providers voice mail system can answer calls for you when you are unavailable to answer the phone or when your line is busy. Messages are recorded by the service provider, not your telephone.
*1 Shown when this call has already been viewed or answered. Press {C} to call back. L OUT OF AREA: When the caller dialled from an area which does not provide Caller ID service. L PRIVATE: When the caller requested not to send caller information. Call Waiting Caller ID This is a service of your service provider and will only operate if you have subscribed to this service. When you hear a call waiting tone during a conversation, the display will show the second callers information. You can answer the second call by pressing {R}. The first caller will be placed on hold.
TCD150E(E).book Page 14 Wednesday, May 25, 2005 4:58 PM

Useful Information

Troubleshooting
If you still have difficulties after following the instructions in this section, disconnect the AC adaptor and turn off the handset, then reconnect the AC adaptor and turn on the handset. Problem w is flashing. Cause & solution L The handset is too far from the base unit. Move closer. L The AC adaptor is not connected. Check the connections. L You are using the handset or base unit in an area with high electrical interference. Locate the handset and base unit away from interference sources, such as antenna and mobile phones. L The handset registration is cancelled. Register the handset to the base unit using the following method.

{j/OK} SETTING HS i {>} REGISTRATION i {>} REGISTER HS i {>} Press and hold {x} on the base unit until the registration tone sounds. L The rest of the procedure must be completed within 1 minute.
6 Select a base unit number ({v}). i {>} 7 Wait until BS PIN is displayed. i Enter
base unit PIN (default: 0000). i {>} L A confirmation tone will sound, and w will stop flashing. I cannot make or receive calls. L The AC adaptor or telephone line cord is not connected. Check the connections. L The call bar feature is turned on. Turn it off (page 10). L You dialled a call restricted number (page 12). L The key lock feature is turned on. Turn it off (page 8). L The ringer volume is turned off. Adjust the ringer volume (page 10, 11). L The handset is not turned on. Turn the power on (page 5).
The unit does not ring. The handset display is blank.
TCD150E(E).book Page 15 Wednesday, May 25, 2005 4:58 PM
Problem The handset will not turn on. Cause & solution L Make sure that the batteries are installed correctly (page 5). L Fully charge the batteries (page 5). L The handset is too far from the base unit. Move closer and try again. L Locate the handset and the base unit away from other electrical appliances. L Move closer to the base unit. L Your unit is connected to a telephone line with DSL service. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack. L You are using the handset or base unit in an area with high electrical interference. Locate the handset and base unit away from interference sources, such as antenna and mobile phones. L The redialled number was more than 24 digits long. Redial the number manually. L Clean the charge contact and charge again (page 5). L It is time to replace the batteries (page 5). L You must subscribe to Caller ID service. L Your unit is connected to a telephone line with DSL service. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack.
A busy tone is heard when {C} is pressed. Static, sound cuts in/out, fades. Interference from other electrical units.
Noise is heard during a call.
Pressing {R} does not display/ dial the last number dialled. I fully charged the batteries, but 074 still flashes. Caller information is not displayed.

TCD150E(E).book Page 16 Wednesday, May 25, 2005 4:58 PM

Specifications

Standard: DECT (Digital Enhanced Cordless Telecommunications) Number of channels: 120 Duplex Channels Frequency range: 1.88 GHz to 1.9 GHz Duplex procedure: TDMA (Time Division Multiple Access) Channel spacing: 1,728 kHz Bit rate: 1,152 kbit/s Modulation: GFSK (Gaussian Frequency Shift Keying) RF transmission power: Approx. 250 mW Power source: 220240 V, 50 Hz Power consumption, Base unit: Standby: Approx. 3.5 W Maximum: Approx. 9.2 W Operating conditions: 5 C40 C, 20 %80 % relative air humidity (dry) Dimensions: Base unit: Approx. 58 mm 123 mm 115 mm Handset: Approx. 143 mm 48 mm 32 mm Mass (weight): Base unit: Approx. 185 g Handset: Approx. 115 g Note: L Specifications are subject to change. L The illustrations used in these operating instructions may differ slightly from the actual product.

Wall mounting

Hooks Hook

Screws

TCD150E(E).book Page 17 Wednesday, May 25, 2005 4:58 PM

Conditions of guarantee

This guarantee is in addition to and does not in any way affect any statutory or other rights of consumer purchasers. If within the applicable guarantee period, the appliance proves to be defective by reason of faulty design, workmanship or materials, we undertake subject to the following conditions to have the defective appliance (or any part or parts there of) repaired or replaced free of charge. 1. The appliance shall have been purchased and used solely within either the UK or ROI and in accordance with standard operating instructions and the technical and/or Safety Standards required in the UK. 2. The appliance should be returned together with this guarantee and proof of date of purchase promptly on being found defective at the purchasers risk and expense to the authorised dealer from whom the appliance was purchased or to the nearest authorised dealer. All enquires must be through such dealers. 3. This guarantee shall not apply to damage caused through fire, accident, lightning, misuse, wear and tear, neglect, incorrect adjustment or repair, to damage caused through installation, adaption, modification or use in an improper manner or inconsistent with the technical and/or safety standards required in the country where this appliance is used, or to damage occurred during transit to or from the purchaser. 4. If at any time during the guarantee period any part or parts of the appliance are replaced with a part or parts not supplied or approved by us or of an objective quality safe and suitable for the appliance, or the appliance has been dismantled or repaired by any person not authorised by us, we shall have the right to terminate this guarantee in whole or in part immediately without further notice. 5. The purchasers sole and exclusive remedy under this guarantee against us is for the repair or replacement of the appliance or any defective part or parts and no other remedy, including, but not limited to, incidental or consequential damage or loss of whatsoever nature shall be available to the purchaser. 6. This guarantee shall not apply to batteries and any other items of limited natural life. 7. Our decision on all matters relating to complaints shall be final. Any appliance or defective part which has been replaced shall become our property. 8. The guarantee period applicable to this product shall be 12 months. Please keep these operating instructions with your receipt. Panasonic Business Systems U.K. Receipt No. Model No. Date of purchase Serial No.

TCD150E(E).book Page 18 Wednesday, May 25, 2005 4:58 PM
TCD150E(E).book Page 19 Wednesday, May 25, 2005 4:58 PM
TCD150E(E).book Page 20 Wednesday, May 25, 2005 4:58 PM
Sales and support information
Customer Care Centre L For customers within the UK: 076 L For customers within the Republic of Ireland: L Visit our website for product information: www.panasonic.co.uk L E-mail: customer.care@panasonic.co.uk Direct Sales at Panasonic UK L Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm (Excluding public holidays). L Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk L Most major credit and debit cards accepted. L All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. L It couldnt be simpler! L Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details.
Customer Care Helpline Tel. No.: U.K. 076 / R.O.I. 01289 8333

1999/5/EC

Sales Department: Panasonic Business Systems U.K. Panasonic House, Willoughby Road, Bracknell, Berkshire, RG12 8FP Panasonic Communications Zhuhai Co., Ltd. 3 Ping Xi 8 Lu, Nanping Keji Gongye Yuan, Zhuhai, Guangdong, China 519060 Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. 2005 Panasonic Communications Co., Ltd. All Rights Reserved.

PQQX14832ZA

DC0605PN0

Note: Use only rechargeable P03P (HHR-4EPT) batteries.

BATTERY

Battery Installation
Insert the batteries negative ( ) terminal first. Close the handset cover.

4.1.2.

Battery Charge
Place the handset on the base unit for about 7 hours before initial use.

4.1.3.

Battery Life

4.2.1.

LOCATION OF CONTROLS

Base Unit

4.2.2.

Handset

Connection

4.4.1.

Guide to Settings
Cross Reference: For Service Hint (P.10)

4.4.2.

For Service Hint
5 DISASSEMBLY INSTRUCTIONS

5.1. Base Unit

Shown in Fig.1 2
To Remove Lower Cabinet Main P.C. Board Screws (2.6 12)..(A) 2 Solders Main P.C. Board

Remove

Shown in Fig.5
To Remove Cabinet Cover Main P.C. Board Screws (2 8)..(B) 2 Follow the procedure. Screw (2 8).(C ) 3 Tapes and Solders Main P.C. Board

Charger Unit

Shown in Fig.6 7
To Remove Lower Cabinet Main P.C. Board
Remove Screws (2.6 14)..(D) 2 Solders Main P.C. Board

6 ASSEMBLY INSTRUCTIONS

6.1. Warning When Constructing the Base Unit
CHG terminal is properly fit in the cabinet.
CHG terminal comes out of rib by pulling black lead wire when opening the cabinet and turning the PCB over. The terminal cannot have enough elastic force, cannot have good contact with handset, and it will result in charge problem.
How to Replace the Handset LCD

7 TROUBLESHOOTING GUIDE

Flow Chart
Cross Reference: Check Power (P.17) Bell Reception (P.22) Check Battery Charge (P.18) Check Link (P.19) Check Handset Transmission (P.21) Check Handset Reception (P.21) SIGNAL ROUTE (P.46)

7.1.1.

Check Power
Is the AC Adaptor inserted into AC outlet? (Check AC Adaptors specification.)
Cross Reference Power Supply Circuit (P.41)

Note: BBIC is IC2.

7.1.2.
Cross Reference Power Supply Circuit/Reset Circuit (P.44)

Note: BBIC is IC1.

7.2.1.

Check Battery Charge

Cross Reference: Power Supply Circuit (P.41)

7.2.2.

Cross Reference: Check Power (P.17) Charge Circuit (P.44)

7.2.3.

Cross Reference: Power Supply Circuit (P.45)

7.3.1.

Check Link
Cross Reference: Power Supply Circuit (P.41) Check Point (Base Unit) (P.23)

7.3.2.

Cross Reference Power Supply Circuit/Reset Circuit (P.44) Check Point (Handset) (P.31)
Check Handset Transmission
Cross Reference: SIGNAL ROUTE (P.46)

Check Handset Reception

Cross Reference: HOW TO CHECK THE HANDSET SPEAKER (P.37). SIGNAL ROUTE (P.46)

Check Caller ID

7.7.1.

Bell Reception

7.7.2.
Cross Reference: Telephone Line Interface (P.42) Check Link (P.19)
8 TROUBLESHOOTING BY SYMPTOM (BASE UNIT AND CHARGER UNIT)
If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester (*1) or not.
Note: (*1) A general repair is possible even if you dont have the DECT tester because it is for confirming the levels, such as Acoustic level in detail. (*2) Refer to Check Point (Base Unit) (P.23)

Check Point (Base Unit)

Please follow the items below when BBIC or EEPROM is replaced. After the measuring, sock up the solder of TP. *: PC Setting (P.27) is required beforehand. The connections of simulator equipments are as shown in Adjustment Standard (Base Unit) (P.28).
Items (A) 2.65V Supply Confirmation Adjustment Point Procedure 1. Confirm that the voltage between TP187 and GND is 2.65V 0.2V. Check or Replace Parts IC2,Q8,C23, C24,C25, C26,C27,C38, R33,R36, D5,C41,R41, R42,Q9, C40,D4,X1, C32,C33, C36,C37 D4,C40,Q9, R41,R42, C41,D5,C75, C78,C69, C66,C67,C76, IC3 IC2,Q8,C23, C24,C25, C26,C27,C38, R33,R36, D5,C41,R41, R42,Q9, C40,D4,R33, X1,C32, C33

4.0V Supply Confirmation

1. Confirm that the voltage between TP91 and GND is 4.0V 0.2V.
VBACK Status Confirmation
1. Confirm that the voltage between J102 and GND is 0V 0.4V.
Items (D)* BBIC Confirmation

Adjustment Point -

Procedure 1. BBIC Confirmation (Execute the command getchk). 2. Confirm the returned checksum value. Connection of checksum value and program number is shown below.
Check or Replace Parts IC2,X1,C32, C33
(E)* BBIC Clock Adjustment (Important)
1. Execute the command deactmac. 2. Execute the command conttx. 3. Input Command rdeeprom 02, then you can confirm the current value. 4. Adjust the frequency of TP1 executing the command setfreq 00 xx (where xx is the value) so that the reading of the frequency counter is 10.368000MHz 10Hz. 1. Connect J1 (Telephone Socket) to Tel-simulator which is connected with 600. 2. Set line voltage to 48V at on-hook condition and line current to 40mA at offhook condition of normal telephone. 3. Execute the command hookoff 4. Confirm that the line current is 40mA 5mA. 5. Execute the command hookon.

Check or Replace Parts IC2,IC3,L1, C43,C78, C75,C69,C48, C72,C66, C67,C76,C57, C73,L3, DA1,R66,R67, C55,C56, R78,R79,C54, C58,C86, R38 IC2,IC3,L1, C43,C78, C75,C69,C48, C72,C66, C67,C76,C57, C73,L3, DA1,R66,R67, C55,C56, R78,R79,C54, C58,C86, R38 IC2,IC3,L1, C43,C78, C75,C69,C48, C72,C66, C67,C76,C57, C73,L3, DA1,R66,R67, C55,C56, R78,R79,C54, C58,C86, R38 IC2,C21,R31, C20,C11, R18,R16,D3, R12,Q2, R7,R8,Q3, R9,R10, D2,C1,C2, R77,IC3, L1,C43,C78, C75,C69, C48,C72,C66, C67,C76, C57,C73,L3, DA1,R66, R67,C55,C56, R78,R79, C54,C58,C86, R38
Items (O)* Transmit Audio Check and Adjustment

Adjustment Point ANT J1

Procedure 1. Configure the DECT tester (CMD60) as follows; <Setting> Test mode: FP Mode: Normal PMID: 00000 2. Execute the command testmode. 3. Initiate connection from DECT tester. 4. Execute the command hookoff. 5. Execute the command openau. 6. Connect J1 (Telephone Socket) to Tel-simulator which is connected with 600. 7. Set line voltage to 48V and line current to 40mA. 8. Input audio signal (30mVrms/1kHz tone) to DECT tester. <DECT tester setting> Scramble: On AF Gen. to ADPCM: On AF Meter Input: AF Voltm AF Gen. Frequency: 1000Hz AF Gen. Level: 30mVrms 9. Confirm hearing tone: 330mVrms 100mVrms. 10. Adjust audio level if required. (Make sure current value using getspkrgain. And then execute the command setspkrgain xx, where xx is the value.)
Check or Replace Parts IC2,R32,C22, R23,C80, C14,C13,R22, R21,Q6, R18,R19,R20, C12,D2, C1,C2,R77, R16,D3, R12,Q2,R7,R8 ,R9, R10,Q3,IC3, L1,C43, C78,C75,C69, C48,C72, C66,C67,C76, C57,C73, L3,DA1,R66, R67,C55, C56,R78,R79, C54,C58, C86,R38

(P) (Q)*

Charging Check Audio Check
11. Confirm that the audio distortion at 600R of Tel-simulator is < 5%. 1. Connect Charge Contact 12/2W resistor between charge+ and charge-. 2. Measure and confirm voltage across the resistor is 2.3V 0.2V. 1. Link with Handset. 2. Set line voltage to 48V and line current to 40mA. 3. Input -45dBm/1kHz to MIC of Handset. Measure the Level at Line I/F and distortion level. 4. Confirm that the level is -23 2dBm and that the distortion level is < 5% at TEL Line (600 Load). 5. Input -20dBm/1kHz to Line I/F. Measure the level at Receiver of Handset and distortion level (*Receive volume set to second position from minimum). 6. Confirm that the level is -9 2dBm and that the distortion level is < 5% at Receiver (Volume Middle, 150 Load).

BBIC Confirmation

1. BBIC Confirmation (Execute the command getchk). 2. Confirm the returned checksum value. Connection of checksum value and program number is shown below.
(D) Charge Control Check & Charge Current Monitor Confirmation
1. Apply 6V between TP20(+) and TP21(-) with current limit of PSU to 250mA. 2. Confirm that the charge current is ON/OFF. 3. SW to decrease current limit of PSU to 100mA.
(E)* Charge Detection (OFF) Confirmation
4. Confirm that the charge current is stable. 1. Stop supplying 6V to TP20(+) and TP21(-). 2. Execute the command charge. 3. Confirm that the returned value is 0x00 (hex).
IC1,D4,L4, L5,Q2,Q3, R6,D2,R22, C26,F1,R21, R4,C33 IC1,D4,L4, L5,Q2,Q3, R6,D2,R22, C26,F1,R21, R4,C33
Items (F)* Battery Monitor Confirmation & Adjustment (Important)
Procedure 1. Apply 2.3V 0.005V between TP3(+) and TP4(-) with DC power. 2. Execute the command deactmac to stabilize the value. 3. Then,execute the command readbatt.The returned value is XX. 4. Confirm that XX is between 98 and A8. 98 < XX < A8(Hex)
Check or Replace Parts IC1,D4,L4, L5,Q2,Q3, R6,D2,R22, C26,F1,R21, R4,C33
(G) Battery low Confirmation (Important)
(If XX is out of range,change BBIC) 1. Apply 2.40V between TP3(+) and TP4(-). 2. Confirm that there is no Speaker sound (Battery low alarm). 3. Apply 2.20V between TP3(+) and TP4(-).
(H)* BBIC Clock Adjustment (Important)
4. Confirm that there is Speaker sound (Battery low alarm). 1. Apply 2.6V between TP 3(+) and TP 4(-) with DC power. 2. Execute the command deactmac. 3. Execute the command conttx. 4. Input Command rdeeprom 01",then you can confirm the current value. 5. Adjust the frequency of TP19 executing the command setfreq 00 xx (where xx is the value).
IC1,F1,R21, R4,C33, C12,C31,R17, R20,C10, C11,D6,D7 IC1,L3,C57, IC3,X1,C16, C17
so that the reading of the frequency counter is 10.368000MHz 10Hz. Remove the Antenna before starting steps from 1 to 5. Replace C58 with RESISTOR (0). Be sure to mount C58 back to the same place after checking. 1. Configure the DECT tester(CMD60) as follows; <Setting> Test mode: PP RFPI: 0102030405 Traffic Channel: 5 Traffic Slot: 4 Mode: Loopback 2. Execute the command testmode. 3. Execute the command regcmd60 4. Initiate connection from DECT tester.
IC1,IC3,C54, C66,C60, L3,C57,C55, C56,C62, R23,R24,C63, C64,C65, R18
5. Confirm that the NTP value at A201 (TP15) is 20dBm ~ 25dBm Follow steps 1 to 4 of (I) above. 5. Confirm that the B-Field Modulation is 340kHz/div ~ 402kHz/div using data type Fig31.

Sensitivity Receiver Confirmation
IC1,IC3,C54, C66,C60, L3,C57,C55, C56,C62, 6. Adjust the B-Field Modulation if required. (Execute the command Readmod R23,R24,C63, and Writemod xx, where xx is the value.) C64,C65, R18 Follow steps 1 to 4 of (I) above. IC1,IC3,C54, 5. Confirm that the frequency offset is -50kHz ~ +50kHz. C66,C60, L3,C57,C55, C56,C62, R23,R24,C63, C64,C65, R18 Follow steps 1 to 4 of (I) above. IC1,IC3,C54, 5. Set DECT tester power to -88dBm. C66,C60, L3,C57,C55, 6. Confirm that the BER is < 1000ppm. C56,C62, R23,R24,C63, C64,C65, R18 Follow steps 1 to 4 of (I) above. IC1,IC3,C54, 5. Confirm that the Timing accuracy is < 2.0ppm. C66,C60, L3,C57,C55, C56,C62, R23,R24,C63, C64,C65, R18 Follow steps 1 to 4 of (I) above. IC1,IC3,C54, 5. Set DECT tester power to -88dBm. C66,C60, L3,C57,C55, 6. Execute the command readrssi C56,C62, R23,R24,C63, 7. Confirm: 25 < returned value < 43 (hex) (0x34 F (hex)) C64,C65, R18
Items (O)* Receive Audio Check and Confirmation

Adjustment Point TP15

Procedure 1. Configure the DECT tester (CMD60) as follows; <Setting> Test mode: PP Mode: Normal RFPI: 0102030405 2. Execute the command testmode. 3. Execute the command regcmd60 4. Initiate connection from DECT tester. 5. Execute the command openaudio. 6. Confirm that the value of EEPROM address F3F is 02. (If the value is not 02 (by User), set 02 and power off and power on, and return to clause 2.) 7. Input audio signal (50mVrms/1kHz tone) from DECT tester. <DECT tester setting> Scramble: On AF Gen. to ADPCM: On AF Meter Input: AF Voltm AF Gen. Frequency: 1000Hz AF Gen. Level: 50mVrms 8. Confirm hearing tone: 300mVrms 250mVrms (Just check Audio path)
Check or Replace Parts IC1,C67,C68, R17,R20, D7,D6,IC3, C54,C66, C60,L3,C57, C55,C56, C62,R23,R24, C63,C64, C65,R18
Transmit Audio Check and Confirmation
9. Confirm that the audio distortion with DECT tester is < 5%. 1. Configure the DECT tester (CMD60) as follows; <Setting> Test mode: FP Mode: Normal RFPI: 0102030405 2. Execute the command testmode. 3. Execute the command regcmd60. 4. Initiate connection from DECT tester. 5. Execute the command openaudio. 6. Confirm that the value of EEPROM address F3F is 02. (If the value is not 02 (by User), set 02 and power off and power on, and return to clause 2.) 7. Input audio signal (30mVrms/1kHz tone) to DECT tester. <DECT tester setting> Scramble: On AF Gen. to ADPCM: Off AF Meter Input: ADPCM AF Gen. Frequency: 1000Hz AF Gen. Level: 30mVrms 8. Confirm hearing tone: 300mVrms 250mVrms (Just check Audio path)
IC1,C8,R7, R8,C6, C7,C5,R5, R1,C4, IC3,C54,C66, C60,L3, C57,C55,C56, C62,R23, R24,C63,C64, C65,R18
Audio Check and Confirmation
9. Confirm that the audio distortion with DECT tester is < 5%. 1. Link to BASE which is connected to Line Simulator. 2. Set line voltage to 48V and line current to 40mA. 3. Input -45dBm/1KHz to MIC and measure Line output level. 4. Confirm that the level is -23 2dBm and that the distortion level is < 5% at TEL Line (600 Load). 5. Input -20dBm/1KHz to Line I/F and measure Receiving level at SP+ and SP-. 6. Confirm that the level is -9 2dBm and that the distortion level is < 5% at Receiver. (vol = middle, 150 Load)

PQUP11176W

CHARGETP21
TP19 SPSP+ 150 AF Volt Meter Oscilloscope GND Frequency (H) Counter

Current Probe

(D) Oscilloscope
(A) - (P) is referred to Check Point (Handset) (P.31)
(*1) Refer to Connections (P.34)
10 THINGS TO DO AFTER REPLACING IC
Cautions: Since this page is common to each country, it may not apply to some models in your country. The contents below are the minimum adjustments required for operation.

10.1. Base Unit

IC Programs for Voice processing, interface for RF and EEPROM EEPROM Adjustment parameter data (country version batch file, default batch file, etc.) BBIC Necessary Adjustment 1. Clock adjustment: Refer to Check Point (E). (*1) 1. Default batch file: Execute the command Default4KB. 2. Country version batch file: Execute the command 150XXvYY. (*2) 3. Clock adjustment: Refer to Check Point (E). (*1)
Note: (*1) Refer to Check Point (Base Unit) (P.23) (*2) XX: country code, YY: revision number XX and YY vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIGs and PC (P.27).

10.2. Handset

BBIC IC Programs for Voice processing, interface for RF and EEPROM Necessary Adjustment 1. Clock adjustment: Refer to Check Point (H). (*3) 2. 4.0 V setting and battery low detection: Refer to Check Point (A), (F) and (G). (*3) 1. Default batch file: Execute the command Default. 2. Default batch file (remaining); Execute the command 115ADJvYY. (*4) 3. Melody Initialize batch file; Execute the Command InitMelodies143vYY 4. Country version batch file: Execute the command 115XXvYY. (*4) 5. Clock adjustment: Refer to Check Point (H). (*3) 6. 4.0 V setting and battery low detection: Refer to Check Point (A), (F) and (G). (*3)
EEPROM Adjustment parameter data (country version batch file, default batch file, etc.)
Note: (*3) Refer to Check Point (Handset) (P.31) (*4) XX: country code, YY: revision number XX and YY vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIGs and PC (P.34).

11 RF SPECIFICATION

11.1. Base Unit
Item TX Power Modulation Frequency Offset RX Sensitivity Timing Accuracy RSSI Level Value More than 20 dBm ~ 25 dBm 340 kHz/div ~ 402 kHz/div -50 kHz ~ +50 kHz < 1000 ppm < 2.0 ppm 0x34 hex F hex Refer to -. * Check Point (Base Unit) (H) Check Point (Base Unit) (I) Check Point (Base Unit) (J) Check Point (Base Unit) (K) Check Point (Base Unit) (L) Check Point (Base Unit) (M)

15.5. Pulse Dialling

During pulse dialing the hookswitch (Q4,Q5) is used to generate the pulses using the HOOK control signal, which is set high during pulses. To force the line impedance low during the pause intervals between dial pulses, the PULSE_DIAL signal turns on Q12.
16 BLOCK DIAGRAM (HANDSET)

42 EARPIECE 45 D/A

Speech Decoding Speech Encoding
Burst Decoding Burst Encoding

12 RXDA 16 TXDA

RF Module 10
48 RSSI Analog Front End TP5 + CHARGE CONTACTS TPEEPROM SCL 67 SDA 66 VDDBAT 36 SWITCHED SUPPLY SWITCH 28 CPU 4.0V D3 VDDLR 34 53~55, 59, 60 ROWS 17~21 CHARGE CIRCUIT CHARGE 38 CHARGE DETECT ADPCM Codec Filter DSP RF Interface 23 SYRI 13 SYEN

BMC 33 XTAL 10.368 MHz

ON SWITCH

TP3 BATTERY TERMINAL TP4

KEYPAD COLUMNS
LCD 14 Seg Display pin 2, 5~9 COM 0~5 segment 0~29
pin1, 90~100, 87, 78~84, 72~76, 61, 62, 56~58
KX-TCA115 BLOCK DIAGRAM (HANDSET)
17 CIRCUIT OPERATION (HANDSET)

17.1. Outline

Handset consists of the following ICs as shown in BLOCK DIAGRAM (HANDSET) (P.43). DECT BBIC (Base Band IC): IC1 All data signals (forming/analyzing ACK or CMD signal) All interfaces (ex: Key, Detector Circuit, Charge, DC/DC Converter, EEPROM, LCD) RF Module: IC3 PLL Oscillator Detector Compress/Expander Amplifier for transmission and reception EEPROM: IC2 Temporary operating parameters (for RF, etc.)
17.2. Power Supply Circuit/Reset Circuit
Circuit Operation: When power on the Handset, the voltage is as follows; BATTERY(2.2 V ~ 2.6V: TP3) TP14(4V) IC3(6, 25), D3 IC1(37) IC1(39, 63) (2.65V) The Reset signal generates R19, C23 and 2.65V.

17.3. Charge Circuit

Circuit Operation: When charging the handset on the Base Unit, the charge current is as follows; DC+(5.5V ~ 6V) D4 R43, R44 CHARGE+(Base) CHARGE+(Handset) L4 Q2 F1 BATTERY+. Battery. BATTERY- R21 GND L5 CHARGE-(Handset) CHARGE-(Base) GND DC-(GND) In this way, the BBIC on Handset detects the fact that the battery is charged. The charge current is controlled by switching Q2 of Handset. Refer to Fig.101 in Power Supply Circuit (P.41).
17.4. Battery Low/Power Down Detector
Circuit Operation: Battery Low and Power Down are detected by BBIC which check the voltage from battery. The detected voltage is as follows; Battery Low Battery voltage: V(Batt) < 2.3V The BBIC detects this level and " Power Down Battery voltage: V(Batt) < 2.2V The BBIC detects this level and power down. " starts flashing and battery alarm starts ringing.

18 CIRCUIT OPERATION (CHARGER UNIT)
18.1. Power Supply Circuit
The power supply is as shown.

19 SIGNAL ROUTE

20 CPU DATA (BASE UNIT)

20.1. IC2 (BBIC)

Pin Description VDD VSS PA_Driver_Amp TX/RX SW RX_Data PLL_Strobe PLL_Data PLL_Clk TX_Data (NO USE) RF_System_Clk VDD VSS RESETQ VDDPM VSSO LOAD XTAL VDDLR LRB VDDA VSSA Audio_Out_N Audio_Out_P Bandgap_Ref Differential_Line_P Differential_Line_N Audio_In_N ADC_Ref RSSI AD2(MPCINP) AD3 (NO USE) (NO USE) (NO USE) (NO USE) VDD VSS Supply_EEP Serial_Data(I2C) Serial_Clk(I2C) MODE (NO USE) BELL/PAGING VBACK (NO USE) (NO USE) VDD (NO USE) (NO USE) (NO USE) (NO USE) VSS VDD KEY_IN (NO USE) PULSE_CTRL (NO USE) (NO USE) (NO USE) HOOK_CTRL (NO USE) I/O D.O D.O D.I D.O D.O D.O D.O D.O D.O A.I D.O D.I A.I A.I A.I A.I A.O A.O A.I A.I A.I A.I A.I A.I A.I A.I D.I D.I D.I D.I D.O D.I/O D.O D.I D.O D.O A.I D.I D.I D.I D.I D.I D.I D.I/O D.I/O D.I/O D.I/O D.I/O D.O D.I/O Hi PA_ON TX Data Latch Normal (I_PU) (I_PU) (I_PU) (I_PU) (Fixed) RINGER_ON (Fixed) No Key Q7_ON Make Hi-z Low PA_OFF RX Data Normal Reset (Fixed) (Fixed) RINGER_OFF (I_PD) (Fixed) (Fixed) (Fixed) (Fixed) Key (I_PD) Q7_OFF (I_PD) (I_PD) (I_PD) Break (I_PD) Remarks 10.368 MHz for Bell Clip for Bell Clip for Polarity for Polarity -

Pin 63 64

Description ANT1 ANT2

I/O D.O D.O

Hi ANT1_ON ANT2_ON

Hi-z -

Low ANT1_OFF ANT2_OFF

Remarks -

Note: I_PU; Internal Pull-Up, I_PD; Internal Pull-Down

21 CPU DATA (HANDSET)

21.1. IC1 (BBIC)
Pin 55 Description LCD_SEGMENT LCD_COMMON VDD VSS LCD_COMMON LCD_COMMON LCD_COMMON LCD_COMMON LCD_COMMON PA_SW T/R SW RX_DATA SYEN SYDA SYCL TX_DATA KEY_IN KEY_IN KEY_IN KEY_IN KEY_IN (NO USE) Reference clock VDD VSS POWER_SW CHARGE_DET DCDCDRV DCDCCMR RESET VSSO LOAD XTAL VDDPM VDDLO VDDBAT VDDLR CHARGE_START VDDA VSSA LSRN LSRP BANDGAP_REF MICS MICP MICN Reference Voltage RSSI P0.4 AD4N AD4P (NO USE) KEY_STRB KEY_STRB KEY_STRB I/O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.I D.O D.O D.O A.O D.I D.I D.I D.I D.I D.O D.O A.I A.I D.O A.I A.I A.I A.I A.O A.O A.I A.O A.O A.O A.O A.O A.I A.I A.O A.I D.I A.I A.I D.I D.O D.O D.O Hi PA ON Transmit No Key No Key No Key No Key No Key SW OFF Charge Non Active Active Active Active Hi-z Low PA OFF Recieve Key_In Key_In Key_In Key_In Key_In SW_ON No_charge Active Non_Active Non_Active Remarks for charge -

Pin 100

Description LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT KEY_STRB KEY_STRB LCD_SEGMENT LCD_SEGMENT VDD VSS VDD for EEPROM I2DAT I2CLK MODE R2 (NO USE) VBACK/P0.7 LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT VDDLI LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT VSS VDD LCD_SEGMENT (NO USE) Power Select LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT LCD_SEGMENT
I/O D.O D.O D.O D.O D.O D.O D.O D.O D.I/O D.I/O D.I D.I D.O D.I D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O D.O
Hi Active Active Low Power -
Low Non_Active Non_Active High Power -

22 ENGINEERING MODE

22.1. Base Unit
Note: *: When you enter the address, please refer to the table below.
Desired Number (hex) 0 1. 9 Input Keys 0 1. 9 Desired Number (hex) A B C D E F Input Keys [R] + 0 [R] + 1 [R] + 2 [R] + 3 [R] + 4 [R] + 5
Items (*2) C-ID (FSK) sensitivity C-ID (DTMF) sensitivity Frequency ID Bell length PULSE Dial speed (10PPS -> 20PPS) Address 0A1D~0A1E 0A 2D 00 00~00 20~0F 12 0F 06 0F 07 0F 0A Default Data 00 6D 60 Given value New Data (3dB up) (6dB up) 00 AE7 (3dB up) (6dB up) 38 3C 14 (2sec) Remarks When hex changes from 006D to 00A4 or 00E7, gain increases by 3dB or 6dB. When hex changes from 34 to 38 or 3C, gain increases by 3dB or 6dB. Use these items in a READ-ONLY mode to confirm the contents. Careless rewriting may cause serious damage to the computer system. This is time until bell stops ringing. (Unit: 100ms) This is pulse make time. (Unit:1ms) This is pulse break time. (Unit:1ms) This is inter-digit time in pulse mode. (Unit:10ms)
64 (10sec) (*1) 1E (3sec) 28 (40msec) (*1) 14 (20msec) 3C (60msec) (*1) 1E (30msec) 4A (740msec) (*1) 2C (440msec)
Bell length PULSE Dial speed (10PPS -> 20PPS) 64(hex) = 100(dec) 100 100msec = 10000msec (10sec) 28(hex) = 40(dec) 40 1msec = 40msec 3C(hex) = 60(dec) 60 1msec = 60msec 4A(hex) = 74(dec) 74 10msec = 740msec
Items C-ID (FSK) sensitivity C-ID (DTMF) sensitivity Frequency ID Bell length PULSE Dial speed (10PPS -> 20PPS) Description FSKGain_shiftgain Foutgains:HPFilter Foutgains Setting value of FREQ_TRIM_REG ID Time until it stops bell. Pulse MakeTime and BreakTime. bMakeTime:Pulse MakeTime Unit: 1ms bBreakTime:Pulse Break Time Unit: 1ms Inter-digit time in Pulse mode. Unit:10ms

3. While the solder melts, remove it together with the IC pins.
When you attach a new IC to the board, remove all solder left on the land with some tools like a soldering wire. If some solder is left at the joint on the board, the new IC will not be attached properly.
23.3. FLAT PACKAGE IC INSTALLATION PROCEDURE
1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins.
*Check the accuracy of the IC setting with the corresponding soldering foil. 2. Apply flux to all pins of the FLAT PACKAGE IC.
3. Solder the pins, sliding the soldering iron in the direction of the arrow.
23.4. BRIDGE MODIFICATION PROCEDURE
1. Lightly resolder the bridged portion. 2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.
24 CABINET AND ELECTRICAL PARTS (BASE UNIT)
25 CABINET AND ELECTRICAL PARTS (HANDSET)
Note: (*1) The rechargeable Ni-MH battery P03P (HHR-4EPT) is available through sales route of Panasonic. (*2) Attach the spacer (No. 117) to the exact location described above. (*3) This cable is fixed by welding. Refer to How to Replace the Handset LCD (P.15).
26 CABINET AND ELECTRICAL PARTS (CHARGER UNIT)
27 ACCESSORIES AND PACKING MATERIALS

27.1. KX-TCD150FXB/FXC

27.2. KX-TCD152FXB
28 TERMINAL GUIDE OF THE ICs, TRANSISTORS AND DIODES

28.1. Base Unit

28.2. Handset

28.3. Charger Unit

29 REPLACEMENT PARTS LIST
1. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. 2. Important safety notice Components identified by the mark indicates special characteristics important for safety. When replacing any of these components, only use specified manufactures parts. 3. The S mark means the part is one of some identical parts. For that reason, it may be different from the installed part. 4. ISO code (Example: ABS-94HB) of the remarks column shows quality of the material and a flame resisting grade about plastics. 5. RESISTORS & CAPACITORS Unless otherwise specified; All resistors are in ohms () K=1000, M=1000k All capacitors are in MICRO FARADS (F)P=F *Type & Wattage of Resistor

D2 D3 D4 D5 D9 DA1 L1 L3 L4 J1 J2 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R16 R18 R19 R20 R21 R22 R23 R24 R25 R26 R27 R28 R29 R30 R31 R32 R38 R41 R42 B0EDER000009 PQVDRLZ20A B0JAME000095 MA2Z74800L MA111 B0DDCM000001 PQLQR4D4R7K G1C4N7Z00007 G1C2N7Z00008 PFJJ1T007Z PQJJ1B4Y ERJ3GEYJ155 ERJ3GEYJ155 ERJ3GEYJ224 ERJ3GEYJ184 ERJ3GEYJ224 ERJ3GEYJ184 ERJ3GEYJ104 ERJ3GEYJ272 ERJ3GEYJ103 ERJ3GEYJ222 ERJ3GEYJ133 ERJ3GEYJ392 ERJ12YJ220 ERJ12YJ560 ERJ3GEYJ104 ERJ3GEYJ333 ERJ3GEYJ560 PQ4R18XJ100 ERJ3GEYJ391 ERJ3GEYJ103 ERJ3GEYJ681 ERJ3GEYJ751 ERJ3GEYJ101 ERJ3GEYJ101 ERJ3GEYJ101 ERJ3GEYJ560 ERJ3GEYJ330 ERJ3GEYJ101 ERJ3GEYJ221 Ref. No. Part No. PQKF10581Z2 PQHA10023Z PQGT18084Z PQGT18084Y Part Name & Description Remarks CABINET COVER ABS-HB FOOT RUBBER NAME PLATE (for KX-TCD150FXB) (for KX-TCD152FXB) NAME PLATE (for KX-TCD150FXC)
29.1.2. Main P.C.Board Parts
Note: (*1) When replacing IC1 and IC2, data need to be written to it with PQZZTCD150FX.
Ref. No. PCB1 IC1 IC2 Q9 Q2 Q3 Q6 Q7 Q8 Q10 Part No. PQWP1D150FXH PQWICD150EH C2HBAK000012 C0CBAYF00016 B1ACGP000007 PQVTBF822T7 2SD1994A B1ABCE000009 B1ADGE000004 B1ABGE000006 Part Name & Description MAIN P.C.BOARD ASSY (RTL) (ICs) IC (EEPROM) (*1) IC (BBIC) (*1) IC (TRANSISTORS) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) (DIODES) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) (COILS) COIL COIL COIL (JACKS) JACK, MODULATOR JACK, DC (RESISTORS) 1.5M 1.5M 220K 180K 220K 180K 100K 2.7K 10K 2.2K 13K 3.9K 100K 33K 390 10K 220 Remarks

29.1. Base Unit

29.1.1. Cabinet and Electrical Parts
Ref. No. Part No. PQGG10245W3 PQGG10245W4 PQKM10586W2 PQJT10203Z PQKE10356Z2 PQSA10182Z PQSA10132Z PQHG10728Z Part Name & Description GRILLE (for KX-TCD150FXB) (for KX-TCD152FXB) GRILLE (for KX-TCD150FXC) CABINET BODY CHARGE TERMINAL GUIDE, CHARGE TERMINAL ANTENNA, MAIN ANTENNA, SUB RUBBER PARTS, BUZZER Remarks ABS-HB ABS-HB ABS-HB POM-HB
Ref. No. R43 R44 R52 R53 R54 R57 R58 R59 R61 R66 R67 R68 R78 R79 R81 R82 R89 R90 C57 L59 C1 C2 C3 C4 C7 C11 C12 C13 C14 C15 C16 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C32 C33 C34 C35 C36 C37 C38 C40 C41 C42 C48 C49 C50 C53 C54 C56 C58 C59 C66 C67 C69 C72 C73 C74 C76 C78 C83 C89

Part No. ERJ1WYJ330 ERJ1WYJ330 ERJ3GEY0R00 ERJ3GEYJ565 ERJ3GEYJ184 ERJ3GEYJ103 ERJ3GEYJ103 ERJ3GEYJ471 ERJ2GEJ470 ERJ3GEYJ180 ERJ3GEYJ151 PQ4R18XJ221 ERJ3GEYJ151 ERJ3GEYJ180 ERJ3GEYJ565 ERJ3GEYJ184 ERJ3GEYJ102 PQ4R18XJ221 ERJ3GEY0R00 ERJ3GEY0R00 ECKD2H681KB ECKD2H681KB ECQE2223KF ECQE2223KF PQCUV1A225KB ECUV1C223KBV PQCUV1C474KB ECUV1A105KBV PQCUV1C224KB ECEA1HKA100 PQCUV1H154KR ECUV1H100DCV ECUV1H100DCV ECUV1C104KBV ECUV1H100DCV PQCUV1C224KB ECUV1C104KBV ECUV1C104KBV ECEA1CKS100 ECUV1C104KBV ECUV1C104KBV ECUV1C683KBV ECUV1C683KBV ECUV1H182KBV ECUV1H270JCV ECUV1H1R0CCV ECUV1C104KBV ECUV1C333KBV ECUV1C104KBV ECUV1C104KBV ECUV1C104KBV ECEA1CK101 ECEA0JKA101 ECUV1H030CCV ECUV1H330JCV ECUV1H103KBV ECUV1H100DCV ECUV1H100DCV ECUV1H060DCV ECUV1H100DCV ECUV1H100DCV ECUV1H100DCV ECUV1H020CCV ECUV1A475KB ECUV1H100DCV ECUV1H020CCV ECUV1H100DCV ECUV1H103KBV ECUV1H060DCV ECUV1H020CCV ECJ1VC1H1R5C ECUV1H102KBV
Part Name & Description 0 5.6M 180K 10K 10K 18 5.6M 180K 1K 0 (CAPACITORS) 680P 680P 0.022 0.022 2.2 0.022 0.0.0.15 10P 10P 0.1 10P 0.22 0.1 0.0.1 0.1 0.068 0.068 0.0018 27P 1 0.1 0.033 0.1 0.1 0.100 3P 33P 0.01 10P 10P 6P 10P 10P 10P 2P 4.7 10P 2P 10P 0.01 6P 2P 1.5P 0.001

Remarks

Ref. No. C90 C94 C96 C97 C98 C100 C101 C105 C106 L58 IC3 CN4 S1 SA1 X1
Part No. ECUV1H101JCV ECUV1H0R5CCV ECUV1H100DCV ECUV1H100DCV PQCUV1H0R5CC ECUV1H100DCV ECUV1H100DCV ECUV1H030CCV ECUV1H030CCV ECUV1H020CCV PQLP10268Z L0DACA000024 K0H1BB000018 J0LF00000026 H0D103500003
Part Name & Description 100P 0.5P 10P 10P 0.5P 10P 10P 3P 3P 2P (OTHERS) RF UNIT BUZZER SPECIAL SWITCH, TACTILE VARISTOR (SURGE ABSORBER) CRYSTAL OSCILLATOR

29.2. Handset

29.2.1. Cabinet and Electrical Parts
Ref. No. 111 Part No. PQGP10225V2 PQHS10553Z PQKM10587Z3 PQKM10587Z2 PQHS10554Y PQBC10375Z1 PQSX10310Z PQHS10719Z PQHX11202Z PQJT10204Z PQJT10205Z PQKF10582Z3 PQKF10582Z2 PQJC10056Y PQJC10057Z PQJC10058Z PQGT18093Z PQGT18093Y PQHX11253X PQHS10561Y PQKK10134X3 PQKK10134X2 Part Name & Description PANEL, LCD TAPE, DOUBLE SIDE CABINET BODY (for KXTCD150FXB) (for KX-TCD152FXB) CABINET BODY (for KXTCD150FXC) SPACER, LCD PUSH BUTTON, NAVI KEYBOARD SWITCH NET, MIC INSULATOR TERMINAL (L) TERMINAL (R) CABINET COVER (for KXTCD150FXB) (for KX-TCD152FXB) CABINET COVER (for KXTCD150FXC) BATTERY TERMINAL BATTERY TERMINAL (-) BATTERY TERMINAL (+) NAME PLATE (for KX-TCD150FXB) (for KX-TCD152FXB) NAME PLATE (for KX-TCD150FXC) PLASTIC PARTS, BATTERY COVER SHEET SPACER, BATTERY COVER LID, BATTERY COVER (for KXTCD150FXB) (for KX-TCD152FXB) LID, BATTERY COVER (for KXTCD150FXC) Remarks AS-HB ABS-HB ABS-HB

29.4. Accessories and Packing Materials
Note: (*1) You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

29.4.1. KX-TCD150FXB/FXC

Ref. No. A1 A2 A3 A4 P1 P2 P3 P4 Part No. PQLV19CEX PQJA10075Z PQQX14847Z PQQT23002Z PFPH1018Z PQPP10084Z PQPK14943Z PQPD10672Z Part Name & Description AC ADAPTOR CORD, TELEPHONE INSTRUCTION BOOK (*1) WEEE LABEL PROTECTION COVER (for Unit) PROTECTION COVER Handset) GIFT BOX CUSHION Remarks

Base (for

29.4.2. KX-TCD152FXB
Ref. No. A1 A2 A3 A4 A5 A6 Part No. PQLV19CEX PQLV200CEX PQJA10075Z PQQX14847Z PQQW14890Z PQQT23002Z Part Name & Description AC ADAPTOR (for Base Unit) AC ADAPTOR (for Charger) CORD, TELEPHONE INSTRUCTION BOOK (*1) LEAFLET, 2 PACK WEEE LABEL Remarks

Ref. No. P1 P2 P3 P4 P5

Part No. PFPH1018Z PQPP10084Z PQPP10086Z PQPK14954Z PQPD10667Z
Part Name & Description PROTECTION Unit) PROTECTION Handset) PROTECTION Charger) GIFT BOX CUSHION COVER (for Base (for (for

COVER COVER

29.5. Fixtures and Tools
Note: (*1) See The Setting Method of JIG (Base Unit) (P.27), and The Setting Method of JIG (Handset) (P.34). (*2) When replacing the Handset LCD, See How to Replace the Handset LCD (P.15).
Part No. PQZZTCD420BX PQZZ1CD705BX PQZZ2CD705BX PQZZ3CD705BX PQZZTCD150FX PQZZ430PIR PQZZ430PRB Part Name & Description I2C PCB (*1) RS232C CABLE (*1) CLIP CABLE (*1) DC CABLE (*1) BATCH FILE CD-ROM (*1) TIP OF SOLDERING IRON (*2) RUBBER OF SOLDERING IRON (*2) Remarks

30 FOR SCHEMATIC DIAGRAM

30.1. Base Unit (SCHEMATIC DIAGRAM (BASE UNIT))
Notes: 1. DC voltage measurements are taken with voltmeter from the negative voltage line.
2. This schematic diagram may be modified at any time with the development of new technology.
30.2. Handset (SCHEMATIC DIAGRAM (HANDSET))
Notes: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
30.3. Charger Unit (SCHEMATIC DIAGRAM (CHARGER UNIT))
31 SCHEMATIC DIAGRAM (BASE UNIT)
L2 TP2 TP5 JMP1 NC TP3 TP39 NC C63 NC R77 NC

LINE VOL TAGE 60V DC

C77 NC JMP6 NC
+60V DC ON-HOOK +10V DC OFF-HOOK 0V ON-HOOK +0.7V DC OFF-HOOK

D2 Q2 TP45

60v DC

680P/500V

2.7K C6
JMP2 NC JMP3 NC JMP4 NC +2.65V

NC R74

C7 10K

220K R5

220K C5
OPTION4 RLY1 NC 1 D10 C3 K0.022 C4 K0.022 R1 1.5M R2

Q11 NC

R72 NC

180K R6

180K C49

D10P D10P C18 C19

(3) (4) (5)