TG8070_TG8090E(e)_QG.fm Page 1 Wednesday, May 30, 2007 11:23 AM

Digital Cordless Phone

Model No.

KX-TG8070E

Digital Cordless Answering System

Quick Guide

Connections

Base unit (KX-TG8070)

KX-TG8090E/KX-TG8092E KX-TG8093E
Base unit (KX-TG8090/KX-TG8092/ KX-TG8093)
To telephone network To AC mains outlet (220240 V, 50 Hz)
To AC mains outlet (220240 V, 50 Hz) To telephone network
Use only the supplied AC adaptor and telephone line cord. Insert the AC adaptor plug until a short beep sounds.
Charger (KX-TG8092/KX-TG8093)
25 mm To AC mains outlet (220240 V, 50 Hz)

Screws

PQQW15624YA

DC0407DM1057

TG8070_TG8090E(e)_QG.fm Page 2 Wednesday, May 30, 2007 11:23 AM
Battery installation/Battery charge

Initial charge: 8 hours

Rechargeable Ni-MH ONLY Base unit *1 Charger *2
*1 The pictured model is KX-TG8070. *2 KX-TG8092/KX-TG8093
Note: L USE ONLY rechargeable Ni-MH batteries. L Do NOT use Alkaline/Manganese/Ni-Cd batteries.

Screen saver mode

If the handset is not on the base unit or charger
The backlight will turn off completely after 1 minute of inactivity, even when: on a call operating the answering system To use the handset when it is in screen saver mode, activate the handset display again by: pressing {^} or {V} when on a call or operating the answering system pressing {i} for all other times

While charging

The backlight will be dimmed after 1 minute of inactivity. The backlight can be turned off completely depending on the setting. To use the handset when it is in screen saver mode, lift the handset to activate the handset display again.
TG8070_TG8090E(e)_QG.fm Page 3 Wednesday, May 30, 2007 11:23 AM

Operating tips

Using the navigator key
Press {^}, {V}, {<}, or {>} to navigate through menus and to select items shown on the display.

{^} {<} {>} {V}

Adjusting the receiver or speaker volume Press {^} or {V} while on a call.

Menu icons

When in standby mode, pressing the right soft key reveals the handsets main menu. From here you can access various features and settings. h x q r SMS (Short Message Service) Caller List Display Setup Handset Setup h s ( Base Unit Setup Answer System*1 Ringer Setup*2
*1 KX-TG8090/KX-TG8092/KX-TG8093 *2 KX-TG8070

Soft keys

The handset features 2 soft keys. By pressing a soft key, you can select the feature or operation indicated by the soft key icon shown directly above it.

INT MENU

Dialling mode (tone/pulse)
{MENU} (right soft key) Select h by pressing {^}, {V}, {<}, or {>}. i {OK} Enter the base unit PIN (default: 0000). i {OK} Press {^} or {V} to select Call Options. i {OK} Press {^} or {V} to select Dial Mode. i {OK} Press {^} or {V} to select the desired setting. i {OK} i {i}

Date and time

{MENU} (right soft key) Select r by pressing {^}, {V}, {<}, or {>}. i {OK} Press {^} or {V} to select Set Date & Time. i {OK} Enter the current date, month, and year. i {OK} Enter the current hour and minute. {OK} i {i}
TG8070_TG8090E(e)_QG.fm Page 4 Wednesday, May 30, 2007 11:23 AM

Basic operations

C Making/Answering calls (Handset) Making calls Answering calls Hanging up Receiver/speaker volume Making a call using the redial list Handset ringer volume Dial the phone number. i {C}/{s} {C}/{s} {i} Press {^} or {V} while on a call. {V/R} i {^}/{V}: Select the desired number. i {C}
{MENU} (right soft key) i r i {OK} {^}/{V}: Ringer Setup i {OK} {^}/{V}: Ringer Volume i {OK} {^}/{V}: Select the desired volume. i {OK} i {i}
k Phonebook (Handset) Adding entries (names and phone numbers) {k} i {MENU} {^}/{V}: New Entry i {OK} Enter the partys name (15 characters max.). i {OK} Enter the partys phone number (24 digits max.). i {OK} i {i} L To enter a name, see the character table in the operating instructions.

Making calls

1 {k} 2 {^}/{V}: Select the desired entry. i {C} 1 {MENU} (right soft key) i s i {OK} 2 {^}/{V}: Answer On/Off i {OK} 3 {^}/{V}: Answer On or Answer Off i {OK} i
s Answering system (Handset): KX-TG8090/KX-TG8092/KX-TG8093 Answering on/off

Listening to messages

1 {MENU} (right soft key) i s i {OK} 2 {^}/{V}: Play All Msg. i {OK}
L The handset plays back all messages, new messages first.
TG8070_TG8090E(e)_QG.fm Page 5 Wednesday, May 30, 2007 11:23 AM
Frequently asked questions
Question Why is w flashing and Register! is shown on the handset display? Cause & solution L The handset is cancelled. If you want to register the handset to the base unit(s), follow Registering a handset to a base unit, page 6. If you want to use a base unit(s) which was registered to the handset before cancellation, select it by following Selecting a base unit in the operating instructions. L The handset is too far from the base unit. Move closer. L The base unit AC adaptor is not connected. Check the connections. L You may have selected the wrong base unit. Select the right base unit. L You are using the handset or base unit in an area with high electrical interference. Place the handset and base unit away from interference sources, such as antennas and mobile phones. L The handset is in screen saver mode. If charging, lift the handset to activate the handset display again. If the handset is not on the base unit or charger, activate the handset display again by: pressing {^} or {V} when on a call or operating the answering system pressing {i} for all other times L Dimmed Backlight is set to Off. Change the setting. L The dialling mode setting is incorrect. Set to Tone or Pulse as needed. L Make sure that the batteries are installed correctly. L Fully charge the batteries. L Clean the charge contacts and charge again. L When you are using fully-charged Ni-MH batteries (supplied batteries); In continuous use: 10 hours max. In continuous standby mode: 100 hours max. L It is normal for batteries not to reach full capacity at the initial charge. Maximum battery performance is reached after a few complete cycles of charge/discharge (use). L Actual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby). L Even after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries. L If the batteries are fully charged until @ is displayed, but / is displayed after a few calls, replace the batteries with new ones.

Why is w flashing and Searching. is shown on the handset display?
Why is the handset display blank?
Why can I not make calls? What should I do when the handset does not turn on? How long is the battery operating time?
Can I keep the handset on the base unit or charger when I am not using it? When should I replace the batteries?
TG8070_TG8090E(e)_QG.fm Page 6 Wednesday, May 30, 2007 11:23 AM
Question What is a PIN? Cause & solution L The PIN is a 4-digit number that must be entered in order to change certain base unit settings. The default PIN is 0000. L You need to subscribe to Caller ID service. Consult your service provider/telephone company for details.
What do I need to do to display caller information?
Registering a handset to a base unit
The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, register the handset.
1 Press and hold {x} on the base unit for
about 5 seconds until a beep is heard. L If all registered handsets start ringing, press {x} to stop, then repeat this step. L After a beep is heard, the rest of this procedure must be completed within 1 minute.

{x} KX-TG8070

{x} KX-TG8090/KX-TG8092/ KX-TG8093
{MENU} (right soft key) i r i {OK} {^}/{V}: Registration i {OK} {^}/{V}: Register Handset i {OK} {^}/{V}: Select a base unit number. i {OK}

{MENU}/{OK}

6 Enter PIN is displayed. Enter the base
unit PIN (default: 0000). i {OK}
TG8070_TG8090E(e)_QG.fm Page 7 Wednesday, May 30, 2007 11:23 AM
Optional services (Caller ID and SMS)
If you subscribe to Caller ID service, you can:

Tom 012345

display caller information
To use SMS, you must subscribe to Caller ID and/or appropriate service.
SMS (Short Message Service)
Sales and support information
Customer Care Centre L For customers within the UK: 3898 L For customers within the Republic of Ireland: L Visit our website for product information: www.panasonic.co.uk L E-mail: customer.care@panasonic.co.uk Direct Sales at Panasonic UK L Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm (Excluding public holidays). L Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk L Most major credit and debit cards accepted. L All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. L It couldnt be simpler! L Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details.

Customer Care Helpline Tel. No.: U.K. 3898 / R.O.I. 01289 8333
TG8070_TG8090E(e)_QG.fm Page 8 Wednesday, May 30, 2007 11:23 AM

IMPORTANT

If you have problems setting up or operating this product please call the Panasonic DECT Helpline 3898 (UK) (Repl of Ireland)