11. To reduce the risk of electric shock, do not disassemble the product. Take the product to an authorized service center when service is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the product is subsequently used. 12. Unplug the product from power outlets and take to an authorized service center when the following conditions occur: A. When the power cord is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not work normally by following the operating instructions. Adjust only controls covered by the operating instructions. Improper adjustment may require extensive work by an authorized service center. E. If the product has been dropped or physically damaged. F. If the product exhibits a distinct change in performance. 13. During thunderstorms, avoid using telephones except cordless types. There may be a remote risk of an electric shock from lightning. 14. Do not use the product to report a gas leak, when in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

WARNING:
L To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. L Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact the Panasonic Call Center at 1-800-211PANA (1-800-211-7262). L Do not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use. L Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. L Completely insert the AC adaptor/ power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.
L Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. L Use caution when installing or modifying telephone lines. L Do not touch the plug with wet hands. L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Battery To reduce the risk of fire or injury to persons, read and follow these instructions. L Use only the battery(ies) specified. L Do not mix old and new battery(ies). L Do not dispose of the battery(ies) in a fire. They may explode. Check with local waste management codes for special disposal instructions. L Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed. L Exercise care when handling the battery(ies). Do not allow conductive materials such as rings, bracelets or keys to touch the battery(ies), otherwise a short circuit may cause the battery(ies) and/or the conductive material to overheat and cause burns. L Charge the battery(ies) provided, or identified for use with the product only, in accordance with the instructions and limitations specified in this manual. Medical L Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to

CAUTION:

Installation L Never install telephone wiring during a lightning storm. L Never install telephone line jacks in wet locations unless the jack is specifically designed for wet locations.
determine if they are adequately shielded from external RF (radio frequency) energy. (The product operates in the frequency range of 1.92 GHz to 1.93 GHz, and the power output is 125 mW (max.).) Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. Environment L Keep the product away from electrical noise generating devices, such as fluorescent lamps and motors. L The product should be kept free from excessive smoke, dust, high temperature, and vibration. L The product should not be exposed to direct sunlight. L Do not place heavy objects on top of the product. L When you leave the product unused for a long period of time, unplug the product from the power outlet. L The product should be kept away from heat sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 5 C (41 F) or greater than 40 C (104 F). Damp basements should also be avoided. L The maximum calling distance may be shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc. L Operating the product near electrical appliances may cause interference. Move away from the electrical appliances. Routine care L Wipe the outer surface of the product with a soft moist cloth. Do not use benzine, thinner, or any abrasive powder.

For best performance

Base unit location/avoiding noise The base unit and other compatible Panasonic units use radio waves to communicate with each other. L For maximum coverage and noisefree communications, place your base unit: at a convenient, high, and central location with no obstructions between the handset and base unit in an indoor environment. away from electronic appliances such as TVs, radios, personal computers, wireless devices or other phones. avoid facing radio frequency transmitters, such as external antennas of mobile phone cell stations (avoid putting the base unit on a bay window or near a window). L Coverage and voice quality depends on the local environmental conditions. L If the reception for a base unit location is not satisfactory, move the base unit to another location for better reception.

Setting up the base unit

Connecting the AC adaptor and telephone line cord
Connect the telephone line cord until it clicks into the base unit and telephone line jack (A). Connect the AC adaptor cord (B) by pressing the plug firmly (C). L Use only the included Panasonic AC adaptor PQLV207.
If you subscribe to a DSL service Please attach a noise filter (contact your DSL provider) to the telephone line between the base unit and the telephone line jack in the event of the following: Noise is heard during conversations. Caller ID features do not function properly.

(120 V AC, 60 Hz)

To single-line telephone jack (RJ11C)
Noise filter C To single-line telephone jack (RJ11C)

Setting up the handset

Connecting the AC adaptor
L Use only the included Panasonic AC adaptor PQLV209.
Note: L The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) L The AC adaptor should be connected to a vertically oriented or floormounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. L The unit will not work during a power failure. We recommend connecting a corded telephone to the same telephone line or to the same telephone line jack using a Panasonic T-adaptor (page 5).
Bottom of the charger Hooks Hooks Fasten the AC adaptor cord to prevent it from being disconnected.
Preparation Battery installation/ replacement 1 Press the notch of the handset cover
firmly, and slide it in the direction of the arrow. L When replacing batteries, remove the old batteries positive (S) end first. Attention:
A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800822-8837) for information on how to recycle this battery.

Battery charge

Place the handset on the base unit or charger for 7 hours before initial use. L While charging, Charging is displayed and the charge indicator on the handset lights. When the batteries are fully charged, Charge completed is displayed. Base unit:
2 Insert the batteries negative (T) end
first. Close the handset cover.
Important: L USE ONLY Ni-MH batteries AAA (R03) size. L Do NOT use Alkaline/Manganese/NiCd batteries. L Install the batteries in proper order (S, T), matching the correct polarity. L When replacing batteries, we recommend using the Panasonic rechargeable batteries noted on page 5, 7. L Wipe the battery ends (S, T) with a dry cloth. L When installing the batteries, avoid touching the battery ends (S, T) or the unit contacts.

Temporary tone dialing (for rotary/pulse service users)
You can temporarily switch the dialing mode to tone when you need to access touch tone services (for example, answering services, telephone banking services, etc.). Press {*} (TONE) before entering access numbers which require tone dialing.
Useful features during a call

MUTE button

While mute is turned on, you can hear the other party, but the other party cannot hear you. To mute your voice, press {MUTE}. L To return to the conversation, press {MUTE} or {C}.

Call share

This feature allows the handset to join an existing outside call. To join the conversation, press {C} when the other handset is on an outside call. Note: L A maximum of 3 parties (including 1 outside party) can join a conversation using 2 extension.

FLASH button

Pressing {FLASH} allows you to use special features of your host PBX such as transferring an extension call, or accessing optional telephone services such as Call Waiting. Note: L To change the flash time, see page 24.
For Call Waiting service users
To use Call Waiting, you must subscribe to Call Waiting service of your telephone service provider. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the For assistance, please visit http://www.panasonic.com/help

Handset phonebook

You can add up to 50 items to the handset phonebook and search for phonebook items by name.

Key {5}

Character J j K k L l o r v Y y 7 s Z z 9 9
M N O 6 m n P p T t Q R S q u U V
Adding items to the phonebook 1 {k} i {MENU} 2 {V}/{^}: New entry i {OK} 3 Enter the name (max. 16

characters). i {OK}

W X w x
4 Enter the phone number (max. 24

digits). i {OK}

Space 0

5 {V}/{^}: Save i {OK}

L To add other items, repeat from step 3.

6 {OFF}

Note: L Step 1 variation: {MENU} i {V}/{^}: Ph.book settings i {OK} Character table for entering names While entering characters, you can switch between uppercase and lowercase by pressing {*}. Key {1} Character Space # ; , {2} A a {3} d {4} g B b e h c F f i &. 4 / ( 1 )

pressing the desired handset number ({1} {6}). L When an item has been copied, Completed is displayed. L To continue copying another item: {V}/{^}: Yes i {OK} i Find the desired item. i {OK}
4 {OFF} Copying all items 1 {k} i {MENU} 2 {V}/{^}: Copy all i {OK} 3 Select the handset to copy to by
pressing the desired handset number ({1} {6}). L When all items have been copied, Completed is displayed.

4 {OFF}

Using Caller ID service
This unit is Caller ID compatible. To use Caller ID features, you must subscribe to Caller ID service of your telephone service provider. Caller ID features When an outside call is being received, the calling partys name and phone number are displayed. Caller information for the last 50 callers is logged in the caller list by the most recent call to the oldest. L Generally caller information is displayed from the 2nd ring. L If the unit cannot receive caller information, the following is displayed: Out of area: The caller dialed from an area which does not provide Caller ID service. Private caller: The caller requested not to send caller information. Long distance: The caller called you long distance. L If the unit is connected to a PBX system, caller information may not be received properly. Consult your PBX supplier. Missed calls If a call is not answered, the unit treats the call as a missed call. The number of missed calls is shown on the display. This lets you know if you should view the caller list to see who called while you were out. Custom name display When the Caller ID number is received and it matches a phone number stored in the phonebook, the stored name from
the phonebook is displayed and logged in the caller list. Call Waiting Caller ID display If you subscribe to both Caller ID and Call Waiting with Caller ID services, the 2nd callers information is displayed after you hear a Call Waiting tone (page 17). Please contact your telephone service provider for details and availability of this service in your area.

Caller list

Viewing the caller list and calling back 1 {MENU} 2 {V}/{^}: View Caller ID i
3 Press {V} to search from the most
recent call, or {^} to search from the oldest call.
4 To call back, press {C}.
To exit, press {OFF}. Note: L A Q is displayed in caller information which has already been viewed or answered.
Editing a callers phone number before calling back
You can edit a phone number in the caller list by removing its area code and/ or the long distance code 1.
1 {MENU} 2 {V}/{^}: View Caller ID i
3 {V}/{^}: Select the desired item. i

You can customize the unit by programming the following features using the handset.
Programming by scrolling through the display menus 1 {MENU} 2 Press {V} or {^} to select the desired menu. i {OK}
L If there is a sub-menu(s), press {V} or {^} to select the desired item. i {OK}
3 Press {V} or {^} to select the desired setting. i {OK}
L This step may vary depending on the feature being programmed.
Note: L In the following table, < > indicates the default setting. Main menu View Caller ID Answering device Sub-menu 1 Play new msg. Play all msg. Record greeting Answer on*1 Answer off*1 Default: Answer on Play greeting Erase message

Sub-menu 2

Page 26
Erase all*1 Erase greeting

Settings

Remote code*1 Default: 111 Ring count*1 <4 rings> Recording time*1 <3 min> Call screening*1 <On> Voice prompt*1 <English>
Main menu Ph.book settings Sub-menu 1 New entry Copy all Erase all Handset settings Ringer settings Sub-menu 2 Ringer volume <Level 6> Ringer tone*2 <Tone 1> Display settings Change language <English> Contrast <Level 3> Registration HS registration Deregistration Other settings Message alert <Off> Key tone*3 <On> Auto talk*4 <Off> Caller ID edit <On> Set date & time Date and time*1 Time adjustment*1, *5 <Caller ID[auto]> Set tel line Set dial mode*1 <Tone> Set flash time*1, *6 <700ms> Customer support Page 19 25
*1 If you program these settings using one of the handsets, you do not need to program the same item using another handset. *2 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 to 5). If you select a melody, you cannot distinguish lines by their ringers. The preset melodies in this product are used with permission of 2006 Copyrights Vision Inc. *3 Turn this feature off if you prefer not to hear key tones while you are dialing or pressing any keys, including confirmation tones and error tones. *4 If you subscribe to Caller ID service and want to view the callers information after lifting up the handset to answer a call, turn off this feature.

3 {V}/{^}: Answer on or Answer

offi {OK} i {OFF}

Screening calls
While a caller is leaving a message, you can listen to the call through the handsets speaker. You can answer the call by pressing {C} on the handset. Note: L To turn this feature off, see page 32.
Answering System 3 {V}/{^}: Play greeting i

Greeting message

When the unit answers a call, callers are greeted by a greeting message. You can record your own greeting message or use a prerecorded greeting message.

{OK} i {OFF}

Erasing your greeting message 1 {MENU} 2 {V}/{^}: Answering device i
Recording your greeting message
You can record your own greeting message (max. 2 minutes and 30 seconds). If you do not record a greeting message, a prerecorded greeting message is used.
3 {V}/{^}: Erase message i
4 {V}/{^}: Erase greeting i
5 {V}/{^}: Yes i {OK} i {OFF}
3 {V}/{^}: Record greeting i
4 After the handset beeps, speak
clearly about 20 cm (8 inches) away from the microphone.
5 To stop recording, press {OK}. 6 {OFF} Using a prerecorded greeting message
If you erase or do not record your own greeting message, the unit plays a prerecorded greeting message for callers and ask them to leave messages.
Playing back the greeting message 1 {MENU} 2 {V}/{^}: Answering device i
Listening to messages using the base unit
When new messages have been recorded, the MESSAGE indicator on the base unit flashes. Press {MESSAGE}. L The base unit plays new messages. L When you have no new messages, the base unit plays back all messages.
Listening to messages using the handset
When new messages have been recorded: New message is displayed. The message indicator on the handset flashes slowly if the message alert feature is turned on (page 32).
Operating the answering system
Key {>} or {<} Operation Adjust the speaker volume (during playback) Repeat message (during playback)*1 Skip message (during playback) Stop playback Erase message currently playing
3 {V}/{^}: Play new msg. or Play

all msg. i {OK}

4 When finished, press {OFF}.
Note: L To switch to the receiver, press {C}. Calling back (Caller ID subscribers only) If caller information was received for the call, you can call the caller back while listening to a message.
{<} {>} {STOP} {ERASE}
1 Press {MENU} during playback. 2 {V}/{^}: Edit & Call i {OK} 3 Press {MENU} repeatedly until the
phone number is shown in the desired format.
*1 If pressed within the first 5 seconds of a message, the previous message is played. Erasing all messages Press {ERASE} 2 times while the unit is not being used.

Erasing all messages

4 {V}/{^}: Erase all i {OK} 5 {V}{^}: Yes i {OK} i {OFF}

{V}/{^}: Settings i {OK} {V}/{^}: Ring count i {OK} {V}/{^}: Select the desired setting. {OK} i {OFF}
Answering system settings

Remote code

A remote code must be entered when operating the answering system remotely. This code prevents unauthorized parties from listening to your messages remotely. The default setting is 111.
3 {V}/{^}: Settings i {OK} 4 {V}/{^}: Remote code i {OK}
For Voice Mail service subscribers If you subscribe to a flat-rate service package that includes Caller ID, Call Waiting, Voice Mail, and unlimited local/ regional/long distance calls, please note the following: L To use the Voice Mail service provided by your telephone service provider rather than the units answering system, turn off the answering system (page 26). L To use this units answering system rather than the Voice Mail service provided by your telephone service provider, please contact your telephone service provider to deactivate your Voice Mail service.
If your telephone service provider cannot do this: Set this units Ring count setting so that this units answering system answers calls before the Voice Mail service of your telephone service provider does. It is necessary to check the ring count required to activate the Voice Mail service provided by your telephone service provider before changing this setting. Change the ring count of the Voice Mail service so that the answering system can answer the call first. To do so, consult your telephone service provider.
2 {V}/{^}: Handset settings i
3 {V}/{^}: Other settings i
4 {V}/{^}: Message alert i
Note: L While message alert is on, battery operating time is shortened (page 11).

Call screening

This feature allows you to monitor a message from the handsets speaker when the answering system is recording a message. The default setting is On.

Callers recording time

You can change the maximum message recording time allotted to each caller. The default setting is 3 min.
3 {V}/{^}: Settings i {OK} 4 {V}/{^}: Call screening i
3 {V}/{^}: Settings i {OK} 4 {V}/{^}: Recording time i
5 {V}/{^}: Select the desired setting. 6 {OK} i {OFF} Message alert
You can select whether or not the message indicator on the handset flashes slowly when new messages are recorded. The default setting is Off. Important: L If there are new Voice Mail messages present (page 33), the message indicator also flashes slowly.

1 {MENU}

Using Voice Mail service
Voice Mail is an automatic answering service offered by your telephone service provider. After you subscribe to this service, the telephone service providers Voice Mail system will answer calls for you when you are unavailable to answer the phone or when your line is busy. Messages are recorded by the telephone service provider, not your telephone. Important: L To use the Voice Mail service provided by your telephone service provider rather than the units answering system, turn off the answering system (page 26). Voice Mail message indication The unit lets you know that you have new Voice Mail messages in the following ways: New Voice Mail is displayed on the handset. The message indicator on the handset flashes slowly if message alert feature is turned on (page 33). In order to listen to your Voice Mail messages, you must dial your telephone service providers Voice Mail access number. Note: L If the handset still indicates there are new messages even after you have listened to new messages, turn it off by pressing and holding {CLEAR} until the handset beeps. L The indication of New Voice Mail may not display properly depending on availability of this service provider.

Please contact your telephone service provider for details.

Message alert

You can select whether or not the message indicator on the handset flashes slowly when there are new recorded messages in the Voice Mail system. The default setting is Off. Important: L If there are new answering system messages present (page 26), the message indicator also flashes slowly.
Multi-unit Operation 2 To stop paging:

Intercom

Intercom calls can be made between handsets Note: L If you receive an outside call while talking on the intercom, you hear 2 tones. To answer the call, press {OFF}, then press {C}. L When paging a unit for an intercom call, the paged unit beeps for 1 minute.
Base unit: Press {LOCATOR}. Handset: Press {OFF}.
Transferring calls between handsets, conference calls
Outside calls can be transferred between 2 handsets. 2 handsets can have a conference call with an outside party.
Making an intercom call 1 {INTERCOM} 2 Select the handset you want to page
by pressing the desired handset number ({1} {6}). L To stop paging, press {OFF}.
1 During an outside call, press
{TRANSFER} to put the call on hold.
2 Select the handset you want to
transfer to by pressing the desired handset number ({1} {6}). L If you do not wish to announce the transfer, skip to step 4.
3 When you finish talking, press

{OFF}.

3 Wait for the paged party to answer.
L If the paged party does not answer, press {C} to return to the outside call.
Answering an intercom call 1 Press {C} or {s} to answer the
4 To complete the transfer:
Press {OFF}. L The outside call is being routed to the handset. To establish a conference call: Press {MENU}. i {1} L To leave the conference, press {OFF}. The other parties can continue the conversation. Note: L If the paged party does not answer within 1 minute after you hang up, your phone rings and the call is returned to your phone. You can speak to the caller again by pressing {C}.

Mount the unit by inserting the mounting pins into the round openings on the adaptor (for pin 2, use round cut out at the bottom of the adaptor if you are using the 4 inches phone plate), then sliding the unit down to secure it. Connect the AC adaptor to power outlet (page 9). L There are two common types of wall phone plates. The distance between 1 and 2 may vary depending on the size of the wall phone plate installed. To remove the wall mounting adaptor While pushing down the release levers (A), remove the adaptor (B).
mm (31/4 inches) or 102 mm (4 inches) 2 (120 V AC, 60 Hz) 83 mm (31/4 inches) 102 mm (4 inches)

Belt clip

You can hang the handset on your belt or pocket using the included belt clip. To attach the belt clip
To remove the belt clip While pressing the top of the clip(A), pull the right edge in the direction of the arrow (B).

Headset (optional)

Connecting a headset to the handset allows hands-free phone conversations. We recommend using the Panasonic headset noted on page 5.
L Headset shown is KX-TCA86.

Error messages

If the unit detects a problem, one of the following messages is shown on the display. Display message Busy Cause/solution L The called handset is in use. L The handset you are calling is too far from the base unit. L There is no handset registered to the base unit matching the extension number you entered. L Other units are in use and the system is busy. Try again later. L Recording was too short. Try again. L The handset you tried to copy phonebook items to is in use. Try again later. L The destination handsets phonebook memory is full. Erase unnecessary items from the destination handsets phonebook (page 19). L There is no space to store new items in the phonebook. Erase unnecessary items (page 19). L There is no space in memory to record new messages. Erase unnecessary messages (page 28). L Your phonebook, caller list or redial list is empty. L The handset has lost communication with the base unit. Move closer to the base unit, and try again. L Confirm that the base units AC adaptor is plugged in. L The handsets registration may have been canceled. Re-register the handset (page 35). L A handset button was pressed while the handset was on the base unit or charger. Lift the handset and press the button again. L In order to set the alarm, you must first set the date and time (page 15).
Error!! Failed Incomplete
Memory full Messages full
No items stored No link to base. Move closer to base, try again.
Please lift up and try again. Please set current date & time.

Troubleshooting

General use Problem The unit does not work. Cause/solution L Make sure the batteries are installed correctly and fully charged (page 10). L Check the connections (page 9). L Unplug the base units AC adaptor to reset the unit. Reconnect the adaptor and try again. L The handset has not been registered to the base unit. Register the handset (page 35). L Confirm the telephone line cord is properly connected (page 9). L Disconnect the unit from the telephone line and connect a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your telephone service provider. L New messages have been recorded. Listen to the new messages (page 28). L New Voice Mail messages have been recorded. Listen to the new Voice Mail messages (page 33).

The caller list/incoming phone numbers are not edited automatically. I cannot dial the phone number edited in the caller list.
Problem The 2nd callers information is not displayed during an outside call. Cause/solution L In order to use Caller ID, Call Waiting, or Call Waiting Caller ID (CWID), you must first contact your telephone service provider and subscribe to the desired service. After subscribing, you may need to contact your telephone service provider again to activate this specific service, even if you already subscribed to both Caller ID and Call Waiting with Caller ID services (CWID).
Answering system Problem I cannot listen to messages from a remote location. Cause/solution L A touch tone phone is required for remote operation. L Enter the remote code correctly (page 31). L The answering system is off. Turn it on (page 31). L The answering system is off. Turn it on (page 26, 31). L The message memory is full. Erase unnecessary messages (page 28, 29). L If you subscribe to the Voice Mail service, messages are recorded by the telephone service provider not your telephone (page 31). L Someone is operating the answering system. L If someone is talking on a conference call, you cannot operate the answering system. Try again later.
The unit does not record new messages.
I cannot operate the answering system.
FCC and other information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------. If requested, this number must be provided to the telephone company. L Registration No.(found on the bottom of the unit) L Ringer Equivalence No. (REN).0.1B A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with the product. It is designed to be connected to a compatible modular jack that is also compliant. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for the product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isnt practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Service Center or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions

Accessory Purchases

Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@us.panasonic.com
You may also contact us directly at: 1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday - Friday 9 am to 9 pm, EST.) Panasonic Service and Technology Company 20421 84th Avenue South, Kent, WA 98032 (We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks.) TTY users (hearing or speech impaired users) can call 1-866-605-1277.

Service in Puerto Rico

Panasonic Puerto Rico, Inc. San Gabriel Industrial Park, Ave. 65 de Infantera, Km. 9.5, Carolina, Puerto Rico 00985 Phone (787)750-4300, Fax (787)768-2910

Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way, Secaucus, New Jersey 07094 PANASONIC PUERTO RICO, INC. San Gabriel Industrial Park, Ave. 65 de Infantera, Km. 9.5, Carolina, Puerto Rico 00985
Panasonic Telephone Products Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto Rico, Inc. (collectively referred to as the warrantor) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (Limited Warranty period), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor. Parts Labor One (1) Year One (1) Year During the Labor Limited Warranty period there will be no charge for labor. During the Parts Limited Warranty period, there will be no charge for parts. You must mail-in your product prepaid during the Limited Warranty period. This Limited Warranty excludes both parts and labor for batteries, antennas, and cosmetic parts (cabinet). This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended only to the original purchaser and only covers products purchased as new.

Alarm: 25 Answering calls: 16 Answering system Erasing messages: 28, 29, 30 Listening to messages: 28, 29, 30 Turning on/off: 26, 29, 30, 31 Auto talk: 17 B Battery: 10, 11 Belt clip: 37 C Call screening: 26, 32 Call share: 17 Call Waiting: 17 Call Waiting Caller ID: 21 Caller ID edit: 21 Caller ID number auto edit: 22 Caller ID service: 21 Caller list: 21, 22 Chain dial: 19 Conference calls: 34 Connections: 9 Customer support: 25 D Date and time: 15 Deregistration: 35 Dialing mode: 14 Display Contrast: 24 Language: 14 E Error messages: 39 F Flash: 17 Flash time: 24 G Greeting message: 27 H Handset locator: 34 Headset, optional: 38 I Intercom: 34 K Key tone: 24 M Making calls: 16 Memory capacity (message recording): 26 Message alert: 32, 33 Missed calls: 21 Mute: 17 A
Navigator key: 13 Pause: 16 Phonebook: 18 Phonebook copy: 20 Power failure: 9 Pulse service: 17 R Recording time: 32 Redial list: 16 Registration: 35 Remote code: 31 Remote operation: 29 Ring count: 31 Ringer off: 17 Ringer tone: 24 Rotary service: 17 S SP-phone: 16 T Time adjustment: 24 Toll saver: 31 Tone: 17 Transferring calls: 34 Troubleshooting: 40 TTY: 5, 48 V Voice guidance: 30 Voice guidance language: 14 Voice Mail: 31, 33 Volume Handset ringer: 24 Receiver: 16 Speaker: 16 W Wall mounting: 36 Warranty: 48 N P
If you need assistance with setup or operation
1 Visit our website: http://www.panasonic.com/help 2 Contact us via the web at: http://www.panasonic.com/contactinfo 3 Call us at: 1-800-211-PANA (1-800-211-7262)
TTY users (hearing or speech impaired users) can call 1-877-833-8855.
When you ship the product
L Carefully pack your unit, preferably in the original carton. L Attach a letter, detailing the symptom, to the outside of the carton. L Send the unit to Panasonic Service and Technology Company Customer Service Center, prepaid and adequately insured. L Do not send your unit to Panasonic Consumer Electronics Company listed below or to executive or regional sales offices. These locations do not repair consumer products.

To order by phone, call 1-800-332-5368 To order by web, visit http://www.pstc.panasonic.com/Epartr/PartsListChoice.asp Model No Spec Ni-MH : 70AAAx3 Model no for telephone Panasonic KX-TGA230 TGA271 TGA272 TG2352 TG2382 Panasonic KX-FPG378 TG2302 TG2318 TG2336 TG2357 TG2880 TG5213 TG5425 TG5438 TG5480 TG5822 TG6500 TG5653

HHR-P103A

Capacity

700mAh

Ni-MH : 90AAAx3 Capacity 830mAh

HHR-P104A

FPG379 TG2303 TG2319 TG2343 TG2386 TG5050 TG5230 TG5426 TG5439 TG5543 TG5831 TG6502 TGA520
FPF 391 TG2308 TG2322 TG2344 TG2388 TG5055 TG5240 TG5428 TG5451 TG5561 TG5832 TG5631 TGA523
TG2312 TG2313 TG2314 TG2316 TG2323 TG2326 TG2328 TG2335 TG2346 TG2348 TG2355 TG2356 TG2396 TG2480 TG2488 TG2489 TG5200 TG5202 TG5210 TG5212 TG5243 TG5421 TG5422 TG5423 TG5431 TG5432 TG5433 TG5436 TG5452 TG5453 TG5456 TG5471 TG5566 TG5571 TG5576 TG5821 TG5838 TG5839 TG5861 TG5871 TG5632 TG5634 TG5651 TG5652 TGA550 TGA551 TGA552 TGA650
Ni-MH : 90AAAx2 Capacity 830mAh

HHR-P105A

Panasonic KX-TG2411 TG2420 TG2421 TG2422 TG2423 TG2424 TG2431 TG2432 TG2433 TG2434 TG2620 TG2621 TG2622 TG2623 TG2624 TG2628 TG2629 TG2631 TG2632 TG2633 TG2634 TG2638 TG2810 TG2811 TG2815 TG2820 TG2822 TG2825 TG2826 TG2831 TG2832 TG2835 TG2836 TG2853 TG2854 TG2873 TG2910 TG2920 TG2922 TG2931 TG2932 TG2935 TG2936 TG5621 TG5631 TG5632 TG5652 TG5672 TG5761 TG5762 TG5766 TG5767 TG5771 TG5776 TG5778 TG5779 TG6700 TG6702 TGA570 TGA571 TGA572 TGA670
Ni-MH : 65AAAx3 Capacity 650mAh
Panasonic KX-TG3021 TG3022 TG3031 TG3032 TG3033 TG3034 TG3510 TG3511 TG3520 TG3521 TG3522 TG3526 TG3531 TG3532 TG3533 TG3536 TG6021 TG6022 TG6023 TG6025 TG6026 TG6031 TG6032 TG6033 TG6034 TG6051 TG6052 TG6053 TG6054 TG6071 TG6072 TG6073 TG6074 TG6075 TGA300 TGA301 TGA351 TGA600 TGA601 KX-GT GT1500 GT1540 GTA150 - IP Phone

HHR-P107A

Ni-MH : 35AAX3 Capacity 350mAh

HHR-P301A

Panasonic KX-T3610 T3620 T3640 T3702 T3705 T3710 T3712 T3720 T3725 T3730 T3732 T3800 T3805 T3807 T3822 T3823 T3824 T3825 T3832 T3848 T3850 T3855 T3860 T3870 T3875 T3908 T3910 T3912 T3920 T3925 T3930 T3932 T3935 T3940 T3945 T3950 T3960 T3962 T3965 T3967 T3968 T3980 T4108 T4109 T4168 T4169 T4200 T4300 T4310 T4330 T4340 T4342 T4350 T4360 T4365 T4370 T4400 T4410 T4500 T4550 T4600 TC100 TC109 TC150 TC155 TC157 TC160 TC162 TC162B TC163 TC165 TC170 TC180 TC183 TC185 TC187 TC190 TC197 TC280 TC282 TC289 TC906 TCC106 TCC116 TCC425 TCM410 TCM410-M TCM412 TCM412-B TCM415 TCM417 TCM418 TCM420 TCM422 TCM424 TCM440 TCM440-B
To order by phone, call 1-800-332-5368 To order by web, visit http://www.pstc.panasonic.com/Epartr/PartsListChoice.asp Model No Spec Ni-MH : 35AAX3 Capacity 350mAh Model no for telephone

HHR-P302A

Fits Cobra, GE, V-Tech, Nortwestern Bell, AT&T Southwestern Bell and SANYO CordlessPhone
Ni-MH : 35AAX3 Capacity 350mAh Fits AT&T, GE, Sears, Sony, Pacific Bell Bell South, Pac.Tel and Mognavox CordlessPhone

HHR-P303A

Ni-MH : 35AAX2 Capacity 350mAh Panasonic KX-TC1000 TC1000B TC1001 TC1001W TC1002
TC1005 TC1010 TC1040 TC1040W

HHR-P305A

Ni-MH : 120AAX3 Capacity 1150mAh
Panasonic KX-TG2396 TG2397 TG2400 TG2400B TG2405 TG2500 TG2505 TG2550 TG2560 TG2565 TG2570 TG2575

HHR-P401A

Ni-MH : 100AAX3 Capacity 1000mAh
Panasonic KX-TG2205 TG2207 TG2215 TG2217 TG2219 TG2227 TG2236 TG2237 TG2239 TG2247 TG2257 TG2267 TG2700 TG2720 TG2730 TG2740 TG2750 TG2770 TG2970 TG2970B TG5100 TG5110 TGA270 TGA273 TGA290 TGA290B TGA510

HHR-P402A

To order by phone, call 1-800-332-5368 To order by web, visit http://www.pstc.panasonic.com/Epartr/PartsListChoice.asp Model No Spec Ni-MH : 70AAX3 Model no for telephone Panasonic KX-TA38 FPC161 FPC165 FPC166 T800 T3800 T3815 T3821 T3830 T3831 T3835 T3842 T3845 T3880 T3900 TC901 TC904 TC907 TC907B TC911 TC917 TC917HSB TC933 TC933B TC934 TC934B TC935 TC935B TC955RUB TC956RUB TC976RUB TC1400 TC1401 TC1401B TC1403 TC1404 TC1405 TC1408 TC1410 TC1410B TC1413 TC1430 TC1430W TC1431 TC1431W TC1447 TC1447PK TC1450 TC1451B TC1451 TC1457 TC1460 TC1460B TC1460W TC1461 TC1461B TC1481 TC1481B TC1484 TC1493 TC1493CB TC1493CW TC1500 TC1501 TC1501B TC1520 TC1520B TC1503 TC1507 TC1696 TC1700 TC1701 TC1701B TC1703 TC1710 TC1710B TC1711 TC1711B TC1713 TC1720 TC1720B TC1721 TC1721B TC1722 TC1723 TC1731 TC1731B TC1733 TC1733CB TC1740 TC1740B TC1741 TC1741B TC1742 TC1743 TC1750 TC1750B TC1800 TC1800B TC1850 TC1850B TC1867 TC1870 TC1870B TC1890 TC1890B TC9568XB TCM939 TCM939B TCM941 TCM943 TCM944 TCM944B TCM947 TCM947B TCL100B Fits IBM, NorthwesternBell, SONY and Uniden Cordless Phone

HHR-P501A

Ni-MH : 150AAX3

HHR-P505A

1500mAh
P-P510A -> Replaced by HHR-P505A
Panasonic KX-TG200 TG200ALB TG200CB TG210 TG210ALB TGM240 TGM240B TC1801 TC1802 TC1805 TC1808 TC1811 TC1812 TC1831 TC1832 TC1851 TC1852 TC1855 TC1858 TC1861 TC1862 TC1863 TC1865 TC1866 TC1867 TC1868 TC1871 TC1872 TC1881 TC1882 TC1886 TC1887 TC1891 TC1892 TG2401 TG2403 TG2451 TG2481 TG2501 TG2502 TG2503 TG2506 TG2551 TG2552 TG2553 TG2559 TG2562 TG2563 TG2564 TG2581 TG2583 TG2584 TG2586 TG2593 TC1801 TC1811B TC1831B TC1851B TC1861B TC1866B TC1871B TC1886B TC1891B
2007.1- REPLACED Ni-MH : 150AAX2 Capacity 1500mAh Panasonic KX-TG2000 TG2000B TG4000 TG4000B TGA200 TGA400 TGA420

HHR-P506A

NI-cd Capacity 500mAh
Panasonic KX-TG2000 2000B TG4000 4000B

P-P507A

To order by phone, call 1-800-332-5368 To order by web, visit http://www.pstc.panasonic.com/Epartr/PartsListChoice.asp Model No Spec Ni-MH : 150AAX2 Capacity 1500mAh Model no for telephone Panasonic KX-TG2650 TG2670 TG2680 TG2650N TG2670N YG2680N TG2690N

HHR-P509A

Ni-MH : 160AAX2 Capacity 1500mAh
Panasonic KX-TG2208 TG2214 TG2216 TG2224 TG2226 TG2235 TG2238 TG2248 TG2258

HHR-P513A

Ni-MH : 70AAX3 Capacity 700Ah
Panasonic KX-T9500 T9505 T9509 T9520 T9550 TC905 TC930

HHR-P543A

No Data
Ni-MH : 150AAX2 Capacity 1500Ah Panasonic KX-TG1000 TG1050 TGA100 TGA100 TGA420B V Tech VT2431 VT2461 AT&T 2455

HHR-P546A

Ni-MH : 70AAX3 Capacity 700mAh
Panasonic KX-TC900 TC900B TC900W TC909 TC910 TC910B TC910DB TC914 TC919 TCC902 TCC912 TCC936 TCC942 TCM937 TCM938 TCM940 TCS970

HHR-P592A

To order by phone, call 1-800-332-5368 To order by web, visit http://www.pstc.panasonic.com/Epartr/PartsListChoice.asp Model No Spec Ni-MH : 150AAX3 Capacity 1500mAh Panasonic Model no for telephone

HHR-P515A

KX-THA16
Ni-MH : 110AAX5 Capacity 1000mAh Panasonic

HHR-P516A

KX-TG4500
Ni-MH : 70AAX1 Capacity 700mAh Panasonic KX-TGA101/1034/1033/1032 No Photo

HHR-4DPA