ORDER NO. MOD0108246C2

Microwave Oven

NE-2156 NE-2146 NE-1656

2001 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
NE-2156 / NE-2146 / NE-1656

CONTENTS

1 OUTLINE DIAGRAM 2 OPERATION PROCEDURE (NE-2156/NE-1656) 3 OPERATION PROCEDURE (NE-2146) 4 SCHEMATIC DIAGRAM NE-SCHEMATIC DIAGRAM NE-2156/NE-WIRING DIAGRAM 7 DESCRIPTION OF OPERATING SEQUENCE MEASUREMENTS AND ADJUSTMENTS 12 TROUBLESHOOTING GUIDE 13 EXPLODED VIEW AND PARTS LIST 14 PARTS LIST 15 DOOR ASSEMBLY 16 ESCUTCHEON BASE ASSEMBLY 17 PACKING AND ACCESSORIES 18 WIRING MATERIAL 19 DIGITAL PROGRAMMER CIRCUIT 20 DIGITAL PROGRAMMER CIRCUIT
8 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE COMPONENT TEST PROCEDURE 19

1 OUTLINE DIAGRAM

2 OPERATION PROCEDURE (NE-2156/NE-1656)
3 OPERATION PROCEDURE (NE-2146)
4 SCHEMATIC DIAGRAM NE-2146
5 SCHEMATIC DIAGRAM NE-2156/NE-1656

6 WIRING DIAGRAM

NOTE: When replacing, check the lead wire colour as shown.
7 DESCRIPTION OF OPERATING SEQUENCE
Variable power cooking control The coil of power relay A and B are energized intermittently by the digital programmer circuit, when the oven is set to MEDIUM or DEFROST power position. The digital programmer circuit controls the ON-OFF time of the power relay A and B contacts in order to vary the output power of the microwave oven. One complete ON and OFF cycle of the power relay is 44 seconds. The relation between indications on the control panel and the output power of the microwave oven is as shown in Figure.
8 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING
Unlike many other appliances, the microwave oven is high voltage, high current equipment. Though it is free from danger in ordinary use, extreme care should be taken during repair.
CAUTION Servicemen should remove their watches whenever working close to or replacing the magnetron.

Check the earthing

If the door lock, the door switch, the door seal or the door develops a malfunction, be sure not to operate the oven until complete repairs are made.
Do not operate on a 2 wire extension cord. The microwave oven is designed to be used in a completely earthed condition. It is imperative, therefore, to make sure it is properly earthed before beginning repair work.
If the oven is operated with any of these parts in imperfect condition, hazardous microwave leakage might occur.
WARNING Never operate the oven until the following are confirmed: 1. The door is tightly closed. 2. There is no broken hinge or door arm. 3. The door seal is not damaged. 4. The door is not bent or warped. 5. There is no other visible damage.
Warning about the electric charge in the high voltage capacitor.
WARNING Never touch any circuit wiring with your hand nor with an insulated tool during operation.
For about 30 seconds after the oven is turned off, an electric charge remains in the high voltage capacitor. When replacing or checking parts, remove the power plug from the outlet, wait 30 seconds and short the terminal of the high voltage capacitor (terminal of lead wire from diode) to chassis ground with an insulated jumper lead wire or an insulated handle screwdriver to discharge.

When parts must be replaced, always remove the power plug from the outlet, and discharge the high voltage capacitor. Confirm after repair
1. After repair or replacement of parts, make sure that the screws of the oven, etc. are neither loose nor missing. Microwave might leak if screws are not properly tightened. 2. Make sure that all electrical connections are tight before inserting the plug into the wall outlet.
Avoid inserting nails, wire, etc. through holes in unit during operation.
Never insert a wire, nail or any other metal object through the lamp holes on the cavity or any other holes or gaps, because such objects may work as an antenna and cause microwave leakage.
CAUTION MICROWAVE RADIATION Personnel should not be exposed to the microwave energy which may radiate from the magnetron or other microwave generating device if it is improperly used or connected all input and output microwave connections waveguides, flanges, and gasket must be secure. Never operate the device without a microwave energy absorbing load attached. Never look into an open waveguide or antenna while the device is energized. Important Note 1. High voltage above 250 volts are existing on following parts during operation. Magnetron High Voltage Transformer High Voltage Diode High Voltage Capacitor Unusual attention should troubleshooting of product. be paid during repair or
CAUTION High voltage parts may become uncovered when outer cabinet is removed.
2. If the microwave oven is operated with incorrect installed door hinge or magnetron, it can cause microwave leakage of over 5mW/sequar centimeter. Hence it is absolutely necessary to check if magnetron and door hinge are correctly and safely installed after repairs or replacement.
9 DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE
1. Discharge electric charge remaining on the high voltage capacitors. 2. Remove the entire rear panel by removing screws as shown. 3. Disconnect all lead wires from magnetron and thermal cutout. 4. Remove the 4 screws holding magnetron.
Replacement of magnetrons (Upper and Lower)

Upper magnetron

5. Remove 2 screws holding thermal cutout. 6. Remove the mounting bracket from magnetron and install it on the new magnetron. Lower magnetron 1. Discharge electric charge remaining on the high voltage capacitors. 2. Remove the entire rear panel by removing screws as shown. 3. Carefully place the unit on its left side (H.V.Capacitor side). 4. Remove the cover by removing 2 screws. 5. Remove the 4 screws holding magnetron by inserting screwdriver through the 4 openings on bottom plate. 6. Remove 2 screws holding thermal cutout. 7. Remove the mounting bracket from magnetron and install it on the new magnetron. NOTE: To prevent microwave leakage, tighten mounting screws properly making sure there is no gap between the waveguide and the magnetron.

CAUTION When connecting 2 filament lead wires to the magnetron terminals, be sure to connect the lead wires in the correct position. The lead wire with blue connector should be connected to FA terminal and white or pink one should be connected to F terminal.
Removal of Positive Lock connector The positive lock connector is a specially designed loose free connector and you will find this connector in many lead wire connections. To remove this connector, pull the lead wire by pressing an extruded lever in the center of receptacle terminal

as shown.

Replacement of power supply circuit board
Be sure to ground any static electric charge built up on your body, before handling the power supply P.C.B. and D.P.C. 1. Disconnect all lead wires from power supply circuit board. 2. Remove the power supply P.C.B. together with its mounting bracket by first removing the 2 bracket holding screws. 3. The power supply P.C.B. can be separated from mounting bracket by removing the 2 L.V.T. holding screws and unfastening the plastic clips.
Replacement of digital programmer circuit board
1. Remove grounding screw for membrane switch and D.P.C. ground. 2. Remove 3 screws holding control panel assembly to detach it from main unit then remove connectors. 3. Remove 2 screws holding the D.P.C. board and while pushing back on 2 plastic holding clips, remove the board. NOTE: Please use care in handling the power supply P.C.B. and D.P.C. board to avoid damage.
Replacement of upper antenna
CAUTION The upper and lower rotating antennas are different type and are not interchangeable each other. Care should be taken not to reverse the top and bottom antennas.
1. Remove ceiling plate by gently moving the left and right tabs inward while pulling the plate down and outward. 2. Using a small flat screwdriver or the like, remove two plastic clips located on the antenna ring. Next turn the antenna ring approx. 1/8 turn clockwise to unhook the tabs and pull off.
Replacement of floor shelf and lower antenna
1. To remove the floor shelf, insert a screwdriver through the small opening on the left side of the oven cavity and carefully lift the floor shelf. 2. For removal of lower antenna, use the same procedure as upper antenna.
Replacement of temperature sensor (Thermal protector)
1. Cut 2 lead wires at the top of sensor terminals. 2. Remove 2 screws holding temp sensor and replace with new one. 3. Solder the lead wires securely to the sensor terminals.
Disassembly of door assembly

1. Remove each 2 bolts holding upper and lower hinges. 2. Open the door and while pulling the door outward, work upper and lower hinges out through the holes of the front surface of oven. 3. Remove door C (choke cover) from door E by carefully pulling outward starting from the upper right hand corner. 4. Remove 2 screws holding door handle and separate door A from door E by carefully freeing catch hooks. 5. Remove door key, door key lever, door key spring and handle pins from door E. 6. Assemble the door by taking the above steps in a reverse order. Replacement 18
1. When mounting the door to the oven be sure to adjust the door parallel to the bottom line of the oven face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment. 2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door assembly is not mounted properly, microwave may leak from the clearance between the door and the oven. NOTE: Please refer to MEASURENMENT AND ADJUSTMENT.
10 COMPONENT TEST PROCEDURE
CAUTION 1. High voltage is present at the high voltage terminal of the high voltage transformer during any cook cycle. 2. It is neither necessary nor advisable to attempt measurement of the high voltage. 3. Before touching any oven components, or wiring, always unplug the oven from its power source and discharge the high voltage capacitor.
check continuity. 2. Normal (cold) resistance readings should be as follows: Secondary winding Approx. Filament winding Approx. 0 Primary winding Approx. 0 3
10.2. High voltage capacitor
1. Check continuity of capacitor with meter on highest OHM scale.
10.1. High voltage transformer
1. Remove connections from the transformer terminals and
2. A normal capacitor will show continuity for a short time, and then indicate 9M once the capacitor is charged. 3. A shorted capacitor will show continuous continuity. 4. An open capacitor will show constant 9M. 5. Resistance between each terminal and chassis should be infinite.

10.4. Diode

1. Isolate the diode from the circuit by disconnecting the leads. 2. With the ohmmeter set on the highest resistance scale, measure the resistance across the diode terminals. Reverse the meter leads and again observe the resistance reading. Meter with 6V, 9V or higher voltage batteries should be used to check the front-to-back resistance of the diode, otherwise an infinite resistance may be read in both directions. A normal diodes resistance will be infinite in one direction and several hundred k in the other direction.

10.3. Magnetron

Continuity checks can only indicate an open filament or a shorted magnetron. To diagnose for an open filament or shorted magnetron. 1. Isolate magnetron from the circuit by disconnecting the leads. 2. A continuity check across magnetron filament terminals should indicate one ohm or less. 3. A continuity check between each filament terminal and magnetron case should read open.

10.5. Membrane key board (Membrane switch assembly)
Check continuity between switch terminals, by tapping an appropriate pad on the key board. The contacts assignment of the respective pads on the key board is as shown in digital programmer circuit.

10.6. Protector diode

1. Isolate the protector diode assembly from the circuit by disconnecting its leads. 2. With the ohmmeter set on the highest resistance scale, measure the resistance across the protector diode terminals. Reverse the meter leads and again observe the resistance reading. A normal protector diodes resistance will be infinite in both directions. It is faulty if it shows continuity in one or both directions.
10.7. Temp sensor (Thermal protector)
A temp sensor is mounted on exhaust guide. Its purpose is to automatically shut off the oven in case the cavity overheats for any reason. The thermal protector will operate at 257F (125C). The device is connected to the DPC on touch control models. When the thermal protector exceeds its temperature it will turn off the power to oven cavity and display will go to reset mode. The cooking program can be reset after cool-down. THERMISTOR RESISTANCE VALUE 30K120K at 10C-30C (50F 86F)
11 MEASUREMENTS AND ADJUSTMENTS
11.1. Adjustment of Safety switch A, Safety switch B and short switch
1. When mounting Safety switch A, Safety switch B and short switch to door hook assembly, mount the Safety switch A, Safety switch B and the short switch to the door hook assembly as shown in table. NOTE: No specific adjustment during installation of Safety switch A, Safety switch B and short switch to the door hook is necessary. 2. When mounting the door hook assembly to the oven assembly, adjust the door hook assembly by moving it in the direction of arrow in table so that the oven door will not have any play in it. Check for play in the door by pulling the door assembly. Make sure that the latch keys move smoothly after adjustment is completed. Completely tighten the screws holding the door hook assembly to the oven assembly. 3. Reconnect the short switch and check the continuity of the monitor circuit and all latch switches again by following the components test procedures. 1. Fill the beaker with exactly one liter of tap water. Stir the water using the thermometer and record the beakers temperature. (recorded as T1) 2. Place the beaker on the center of glass cook plate. Set the oven for High power and heat it for exactly one minute. 3. Stir the water again and read the temperature of the beaker. (recorded as T2) 4. The normal temperature rise (T2-T1) at High power position for each model is as shown in table.

11.2. Measurement of microwave output
The output power of the magnetron can be determined by performing IEC standard test procedures. However, due to the complexity of IEC test procedures, it is recommended to test the magnetron using the simple method outlined below. Necessary Equipment: 1 liter beaker Glass thermometer Wrist watch or stopwatch NOTE: Check the line voltage under load. Low voltage will lower the magnetron output. Take the temperature readings and heating time as accurate as possible. TABLE (1 liter-1 min. test)
RATED OUTPUT 2100 W (IEC-705) 1600W (IEC-705) TEMPERATURE RISE Min. 18C Min. 14.5C

12 TROUBLESHOOTING GUIDE

CAUTION 1. Check grounding before checking for trouble. 2. Be careful of the high voltage circuit. 3. Discharge high voltage capacitor. 4. When checking the continuity of the switches or the high voltage transformer, disconnect one lead wire from these parts and then check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter. When disconnecting a plastic connector from a terminal, you must hold the plastic connector instead of the lead wire and then disconnect it, otherwise lead wire may be open or the connector cannot be removed. 5. Be sure to ground any static electric charge built up in your body, before handling the D.P.C. 6. A 230-240V AC is present at the shaded area ( ) of the power supply circuit board (Terminals of power relays and primary circuit of low voltage transformer). When troubleshooting, be cautious of possible electrical shock hazard.
First of all operate the microwave oven following the correct operating procedures described on pages 3 of this service manual in order to find the exact cause of any trouble. NOTE: If the unit shows faulty symptom as shown below, check the parts listed in possible cause column depending on failure indication e.g. F81, F82 in the display. [TROUBLE 1] Oven does not operate at all or oven does not start cooking.
DISPLAY F33 CONDITIONS Open temperature sensor (exhaust) POSSIBLE CAUSE 1. Temperature sensor failure 2. Digital programmer circuit failure 3. Loose connector CN4 1. Temperature sensor failure 2. Digital programmer circuit failure 1. Shorted power select switch 2. Shorted membrane switch 1. Burning food in the oven due to over cook It is appeared when failure occured. It is appeared 2 minuted after failure occured. It is appeared when exhaust temperature exceeds above 120C. TIMING OF FAILURE INDICATION It is appeared when failure occured.
F34 F44 F01 (With continuous beep sounds) F05 No display No display
Short temperature sensor (exhaust)
Exhaust temperature exceeds 120C Memory failure 1.25A fuse blown 1.25A fuse is OK
1. Digital programmer circuit failure 1. Switch failure SW4, SW5, SW6, SW7 2. Low-Voltage transformer failure 1. Switch failure SW1, SW2, SW3 2. Low voltage transformer failure 3. Digital programmer circuit failure 1. Relay failure RY-3 2. 10A fuse open 3. Digital programmer circuit failure 1. Relay failure RY-4 2. 10A fuse open 3. Digital programmer circuit failure 1. Relay failure RY-3 2. Digital programmer circuit failure 1. Relay failure RY-4 2. Digital programmer circuit failure It is appeared when failure occured. It is appeared when failure occured. It is appeared when cooking is completed.

No voltage supply to high voltage transformer (upper) No voltage supply to high voltage transformer (lower) Shorted contacts of RY3 Shorted contacts of RY4
It is appeared when cooking is completed.

F86 F87

13 EXPLODED VIEW AND PARTS LIST

14 PARTS LIST

NOTE When ordering replacement part(s), please use part number(s) shown in this parts list. Do not use description of the part. Important safety notice: Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer s specified parts.
Ref. No. Part No. 1 A00064080BP 1 ANE00062Q0EP 2 ANE0072Z70GP 3 ANE010T8U0AP 4 A02393A80BP 5 A05243A80BP 5 A05243A90BP 5 A05243A80EU 5 A05243A90EU 5 A05243A30EU 6 ANE0901000CD 7 ANE000Z000AD 7 ANE000Z000AD 7 ANE000Z000AD 7 ANE000Z000AD 8 ANE0911000MG 9 A8251-ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 10 ANE000Z000AA 11 XYEANE5+C16T 11 XYEANE5+C16T 11 XYEANE5+C16T 11 XYEANE5+C16T 12 ANE000Z000AB 13 ANE0962000AP 14 ANE0962000AV 15 A100A-A100Q-A1008-A1008-A1008-A1008-ANE10098U0AP 19 ANE10268U0AP 20 ANE10288U0AP 21 ANE10498U0AP 22 ANE1062-8UANE1062-8UANE1062-8UXTWANE3+8EX 23 XTWANE3+8EX 23 XTWANE3+8EX 23 XTWANE3+8EX 24 ANE11268U0AP 25 2M244-M1G 25 2M210-M1G 26 ANE11408A0AG 27 A11543170GP 28 ANE11668U0AP 29 ANE11748U0AP 30 A200A-A2011-3280S 32 A202K-A202R3320GP 34 ANE21208U0AP 35 A3020-3850 Part Name & Description CAUTION LABEL CAUTION LABEL CAUTION LABEL SHELF CORD LABEL NAME LABEL NAME LABEL NAME LABEL NAME LABEL NAME LABEL CUSHION RUBBER A CUSHION RUBBER A CUSHION RUBBER A CUSHION RUBBER A CUSHION RUBBER A CUSHION RUBBER B SPACER CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C CUSHION RUBBER C SCREW SCREW SCREW SCREW CUSHION RUBBER C CUSHION RUBBER D CUSHION RUBBER D BASE BACK PANEL RUBBER FOOT RUBBER FOOT RUBBER FOOT RUBBER FOOT CABINET BODY LAMP COVER ANTENNA MOTOR COVER CUSHION RUBBER CUSHION RUBBER B CUSHION RUBBER B CUSHION RUBBER B SCREW SCREW SCREW SCREW BASE BRACKET MAGNETRON MAGNETRON STOPPER BACK PANEL COVER BASE METAL SPACER OVEN CEILING PLATE ANTENNA(U) ANTENNA B(U) SPACER DOOR HOOK Pcs/Set 1 Remarks FOR BPQ FOR EUG
FOR BPQ NE-2156BPQ NE-2146BPQ NE-2156EUG NE-2146EUG NE-1656EUG NE-2156,NE-1656 NE-2146 NE-2156,NE-1656 NE-2156,NE-1656
5X16(FOR 5X16(FOR 5X16(FOR 5X16(FOR
MAGNETRON) MAGNETRON) MAGNETRON) MAGNETRON)
W/OUT FOOT & RUBBER FOOT (NOTE)
3X8(FOR 3X8(FOR 3X8(FOR 3X8(FOR

FOOT) FOOT) FOOT) FOOT)

Ref. No. Part No. 36 A3136-A3137-A3138-A31863A30EU 39 A31863A80BP 39 A31863A90BP 40 ANE32398U0AP 41 ANE32628U0AP 41 ANE32628U0AP 42 A400A3310GP 42 A400A3310GP 43 A400B-A400K-ANE40258U0AP 46 ANE40268U0AP 47 A4091-ANE41038U0AP 49 ANE50328U0AP 49 ANE50328U0AP 50 A601L5150AP 51 A603L3A30EU 51 A603L3A80BP 51 A603L3320GP 52 ANE6030Q50GN 53 ANE60408UAP 53 ANE60408UAP 54 A606V-A606W-ANE60708U0BP 57 A6070-A6070-A60713310BP 59 ANE6142-FANE61424L0AG 61 A6144-A61446030AP 63 A61454000AP 64 A61454210AP 64 A61454210AP 65 ANE61522Q0BP 66 ANE6161-3XA6170-ANE61888U0AP 69 A6202-A62024000AP 70 ANE62298U0AP 71 A62303A80BP 71 A62304210BP 72 ANE6238X20AP 73 A63903A80BP 73 A63903430GP 74 ANE64086Q0AP 75 A6408-ANE65448U0AP 77 A6585-A65943030GP 79 A65953170GP 80 ANE66038U0BP 81 A6688-A692M3310GP 83 A692Y3A90BP 84 A910A3A80BP 84 A910A3310GP 85 ANE900T8V0AP 85 ANE900T8V0AP 86 ANE90828U0AP 87 XYN40F10BN 88 ANE91438U0AP 89 ANE91448U0AP 90 ANE91628U0AP 91 A622A3A80EU 91 A622A3310GP 92 XTC4+10BC 92 XTC4+10BC

Part Name & Description HOOK SPACER A HOOK SPACER B HOOK SPACER C DOOR PANEL DOOR PANEL DOOR PANEL SPRING SPRING SPRING FAN MOTOR FAN MOTOR AIR FILTER FLAME EXHAUST GUIDE AIR GUIDE A AIR GUIDE B SCREW AIR GUIDE CUSHION B MAGNETRON BRACKET MAGNETRON BRACKET TEMP SENSOR D.P.CIRCUIT(U) D.P.CIRCUIT(U) D.P.CIRCUIT(U) INCANDESCENT LAMP OVEN LAMP SHEET OVEN LAMP SHEET PROTECTOR DIODE PROTECTOR DIODE B INSULATION SHEET A INSULATION SHEET A INSULATION SHEET A INSULATION SHEET B MICROSWITCH MICROSWITCH ANTENNA MOTOR ANTENNA MOTOR THERMAL CUTOUT THERMAL CUTOUT THERMAL CUTOUT SOCKET MICROSWITCH INSULATION SHEET C CAPACITOR BRACKET DIODE,SI DIODE,SI MOUNTING BRACKET FUSE FUSE SPACER H.V.CAPACITOR H.V.CAPACITOR WASHER WASHER SPACER A P.C.B.HOLDER MOTOR COVER FUSE OVEN LAMP BRACKET COVER L.V.TRANSFORMER(U) NOISE FILTER(U) AC CORD W/OUT PLUG(U) AC CORD W/PLUG (U) CLIP CLIP CLIP(BLACK) SCREW CLIP(GRAY) BRACKET CLIP B H.V.TRANSFORMER H.V.TRANSFORMER SCREW SCREW

Pcs/Set 4 4

Remarks

NE-1656 NE-2156 NE-2146

(55W) (55W)
UPPER LOWER FOR AIR FILTER FRAME
NE-1656 NE-2156 NE-2146 (240V 25W)
CONNECTOR COLOUR:RED CONNECTOR COLOUR:BLUE
(V-15G-3C26)SECONDARY LATCH SWITCH (V-16G-3C26)PRIMARY LATCH SWITCH LOWER(2.5W) UPPER(2.5W) FOR OVEN FOR MAGNETRON FOR MAGNETRON (V-16G-1C25)SHORT SWITCH
NE-2156,NE-2146 NE-1656 NE-2156,NE-2146(12A) NE-1656(10A) NE-2156,NE-2146(1.14MF,AC2300V) NE-1656(0.93MF,AC2300V) NE-2156,NE-1656 FOR AIR FILTER FRAME

(1.25A)

BPQ EUG FOR ANTENAA(U) FOR ANTENAA(U) FOR AIR FILTER 4X10(FOR NOISE FOR BACK PANEL
ANTENNA B (U) ANTENNA B (U) FRAME FILTER(U))
FOR AIR GUIDE A NE-2156 NE-2146 NE-1656(1.5KVA) 4X10(FOR CABNET BODY) 4X10(FOR CABNET BODY)
Ref. No. Part No. 92 XTC4+10BC 93 XTC4+10FC 94 XTC4+12BK 94 XTC4+12BK 95 XTT4+8E 96 XWC4BPN 96 XWC4BPN 97 XYD4+EE12F
Part Name & Description SCREW SCREW SCREW(BLACK) SCREW(BLACK) SCREW WASHER WASHER SCREW

Pcs/Set 2 10

XYD4+EE12F

101 101

XSWANE5+10U XSWANE5+10U A10923310GP A61713A80BP A1007-3280 A1007-3280 A1007-3280 A1007-3280
SCREW SCREW INTERRUPTION COVER B INSULATION SHEET D FOOT A FOOT A FOOT A FOOT A
Remarks 4X10(FOR CABNET BODY) 4X10(FOR LAMP COVER) 4X12(FOR BASE) 4X12(FOR BASE) 4X8(FOR BACK PANEL COVER) FOR BACK PANEL COVER LAMP COVER) FOR BACK PANEL COVER LAMP COVER) NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2156,NE-1656(4X12)FOR MOUNTING BRACKET, DIODE ,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER ,BASE METAL,WASHER NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL NE-2146(4X12)FOR MOUNTING BRACKET, DIODE,CAPACITOR BRACKET,AC CORD, ANTENNA MOTOR COVER,BASE METAL 5X10(FOR HINGE) 5X10(FOR HINGE)
NOTE: Please order name label together.

15 DOOR ASSEMBLY

Ref. No. Part No. D1 ANE3003-3510 D2 ANE30078U0AP D2 ANE30078U0AP D3 ANE301A8U0AP D4 ANE301H-3850 D5 ANE301Q-3500 D6 ANE3018-3850 D7 ANE3019-3850 D8 ANE30218U0AP D9 ANE30562Q0AP D9 ANE30562Q0AP D10 A30703170GP D11 ANE3081P60AP D12 ANE30858U0AP D13 ANE31348U0AP D14 ANE3145-3500 D15 ANE31468U0AP D16 XYE4+C16TS D16 XYE4+C16TS
Part Name & Description DOOR FRAME(U) HINGE HINGE DOOR A DOOR KEY LEVER B DOOR E(U) DOOR KEY DOOR KEY B DOOR KEY SPRING HANDLE PIN HANDLE PIN HANDLE PIECE A DOOR HINGE SPACER DOOR C HANDLE PIECE B DOOR SCREEN A DOOR SCREEN B SCREW SCREW

Pcs/Set 2

4X16(FOR DOOR E) 4X16(FOR DOOR E)
16 ESCUTCHEON BASE ASSEMBLY
Ref. No. Part No. E1 ANE03558Y0BP E2 A603M3310GP E2 A603M3310GP E3 ANE605Q8Y0BP E4 ANE61424L0AG E5 ANE61628Y0BP E6 ANE62648Y0BP E7 ANE63438Y0BP E8 A64793310GP E9 A6590-3280 E9 A6590-3280 E10 ANE800D8Y0BP E11 ANE801N8Y0BP E11 ANE801N8U0AP E12 ANE80028U0AP E12 ANE80028U0AP E13 ANE80068U0AP E13 ANE80068U0AP E14 ANE803X8Y0BP E15 ANE80348Y0BP E15 A800D3310GP E16 ANE80378Y0BP E17 A81263320GP E18 ANE0921000BA E18 ANE0921000BA E19 ANE82878Y0BP E20 A83373320GP E20 A8337-3280

Part Name & Description TIMER P.C.BOARD B(U) P.C.BOARD B(U) P.C.BOARD F(U) MICROSWITCH START SWITCH BRACKET SELECT SWITCH BUTTON TIMER BRACKET MEMBRANE SWITCH FLAT CABLE FLAT CABLE TIMER KNOB ESCUTCHEON A(U) ESCUTCHEON A(U) ESCUTCHEON B ESCUTCHEON B ESCUTCHEON D ESCUTCHEON D START BUTTON ESCUTCHEON BASE ESCUTCHEON BASE(U) COOK BUTTON SPRING SMOKE PANEL CUSHION RUBBER C CUSHION RUBBER C SPACER A ESCUTCHEON SHEET ESCUTCHEON SHEET

Pcs\Set NE-2146

NE-2146 NE-2146(V-16G-3C26) NE-2146 NE-2146 NE-2146 NE-2156,NE-1656
NE-2146 NE-2146 NE-2156,NE-1656
NE-2146 NE-2146 NE-2156,NE-1656 NE-2146 NE-2146 NE-2146 NE-2146 NE-2146 NE-2146 NE-2156,NE-1656
17 PACKING AND ACCESSORIES
Ref. No. Part No. P1 A00033A80BP P1 A00033A80EU P2 A01023A80BP P2 A01023A90BP P2 A01023A30EU P3 ANE01048U0AP P4 ANE01058U0AP P5 A01065200AP P6 ANE01072Q0AP P7 A01083310GP P8 A01453230BP P9 A04203310BP P10 A1134-3280
Part Name & Description INSTRUCTION BOOK INSTRUCTION BOOK PACKING CASE,PAPER PACKING CASE,PAPER PACKING CASE,PAPER UPPER FILLER LOWER FILLER VINYL COVER DOOR SHEET TRAY PACKING DOOR SHEET B OPERATING GUIDE FOOT BRACKET
Pcs/Set 1 BPQ EUG NE-2156 NE-2146 NE-1656

NE-2156,NE-1656

18 WIRING MATERIAL
Ref. No. Part No. W1 A030A3310GP W2 A030H3310GP W3 A03543320GP W4 A50966520UP W4 A50966520UP W4 A50966520UP W5 A61393230BP Ref. No. C1 C2,C3 Part No. ECQE2A474MWA ANE6169A20GN
Part Name & Description LEAD WIRE HARNESS LEAD WIRE HARNESS LEAD WIRE FERRITE CORE FERRITE CORE FERRITE CORE INSULATION TUBE

Pcs/Set 1

NE-2146
Part Name & Description Pcs/Set REF NO. 83 NOISE FILTER (U) POLYESTER CAPACITOR 1 0.47MF,250V,20% CAPACITOR 2 0.022MF,250V,20%
Ref. No. Part No. CN10 AEEMMD00703W D1 ERZC10DK621F D2,D3 ERZC10DK112R F1,F2 A62316010BP F3 A62316000GP L1 A621A3310GP R1 ERF15ZXJ240 ANE61158U0AP ANE65448U0AP ANE65458U0AP A6338-3280 XYN3+F25S CN100 AEEMMF01F05W CN101 AEEMMF03F06W CN102 AEEMMD04907W CN103 AEEMMD04907R CN104 AEEMMF00703W CN105 AEEMMF00703R CN106 AEEMMD24910W D100,D101 MA196-(TA5) ,D102,D10 3,D104,D1 05,D108 D106,D107 AEDNERA1506 IC100,IC1 AEICP25011HL 01 R100,R101 ERDS1TJ434T ,R102,RRY1 AEBG5B18P-1 RY2 AEBG5B1E18 RY3,RY4,R AEG5J1EM18B Y5 T100 ETP43KZN61CN ANE82848U0AP AEEMHLEM21S A64563080AP
Part Name & Description Pcs/Set CONNECTOR 1 3PIN VARISTOR 1 VARISTOR 2 FUSE HOLDER 4 FUSE HOLDER 2 FILTER COIL 1 RESISTOR 1 24,15W,5% REF NO. 82 L.V.TRANSFORMER (U) POWER RELAY BRACKET 1 SPACER A 6 SPACER B 2 INSULATION SHEET B 1 SCREW 2 3X25 CONNECTOR 1 5PIN CONNECTOR 1 6PIN CONNECTOR 1 7PIN CONNECTOR 1 7PIN CONNECTOR 1 3PIN CONNECTOR 1 3PIN CONNECTOR 1 10PIN DIODE,SI 7
DIODE,SI L.S.I CARBON FILM RESISTOR

CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
FILM FILM FILM FILM FILM FILM FILM FILM FILM
RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR
22,1/4W,5% 10K,1/4W,5% 680,1/4W,5% 33K,1/4W,5% 3.3K,1/4W,5% 4.7K,1/4W,5% 180K,1/4W,5% 100K,1/4W,5% 47,1/4W,5%
ZENER DIODE,SI ZENER DIODE,SI ZENER DIODE,SI
WP-592 (F) S-3A8 BPQ Printed in Japan

BEUK HORECA

I N T E R N A T I O N A L

Ovens & microwaves

If you would like to know more about one of our products please visit our internet site for more details, specifications and larger pictures.

OVENS & MICROWAVES

Convection-oven BEUK HORECA Convection-oven 2/3 GN measurements

50 C - 275 C

Picture Model Size mm (wxdxh) Description Content Capacity Size (wxdxh) Power kW Volt kg

*BE60UK*

BE60UK
Hotair analog control 625x600x600 panel 2/3 GN measurements

4 grids

340x430 mm

2,7 230

*BE115UK*

B E U K

690x700x510
Hotair liquid-injection analog control panel 2/3 GN measurements

3,3 230

1.395,-
Electric GN convection-oven
Entirely of AISI 304 stainless steel Stainless steel bakingspace The door is left hinged Including 4 grids 340x435 mm Suitable for 1/2, 1/3 and 2/3 GN-containers 1 autoreverse turbo engine Manual direct water-injection Timer from 10 up to 120 minutes with a buzzer as endingsignal Separate on/off switch
Entirely of AISI 304 stainless steel To be used for bake off, snacks, pizza, pasta, fish, meat, dishes. With 2 powerfull fans. Stainless steel oven casing/body and frame. Timer from 5 up to 120 minutes with continously position. Thermostat adjustable from 50 C up to 275 C. Separate on/off switch. Door with microswitch. Delivered with 4 adjustable feet. Including 4 grids 340x430 mm.
A l l p r i c e s a r e w i t h o u t VAT a n d c a n b e c h a n g e d a t a n y t i m e w i t h o u t p r i o r n o t i c e. A l l t e c h n i c a l i n f o r m a t i o n , d r a w i n g s , p i c t u r e s , w e i g h t s a n d m e a s u r e s , m o s t c a r e f u l l y p r e s e n t e d , a r e l i s t e d u n d e r r e s e r v a t i o n a n d d o n o t b i n d t h e s u p p l i e r i n n o w a y. O u r c o m p a n y r e s e r v e s the right to change designs without prior notice. Our general terms and sales conditions apply to all our products, offers and deliveries.
Convection-oven Convection-oven 1/1 GN measurements

BE230UK

Completely of AISI 304 stainless steel. Door with hardened glass and an easily replaceable gasket. Indoor lighting. Electronic thermostat. Temperature: 50 C - 275 C. Timer. Connection for water with manual water-injection. Two heavy fans which turn left and right alternately. to guarantee a good heat distribution through the whole oven. Internally the oven can be used without extra accessories, with gastronome containers and grids. (530x325 mm) as well as bakery norm (600 x 400 mm). Also very useful for out of door catering purposes.

Picture

Size mm (wxdxh)

Description

Content Capacity Size (wxd)

Power kW Volt

*BE230UK*
Hotair liquid-injection 880x750x525 analog control panel 1/1GN measurements
600x400 mm 4 grids 530x325 mm 3,35

2.095,-

*BEUKINF*

BEUKINF

Stainless steel wallframe for the ovens: BE60UK, BE115UK & BE230UK

Convection-oven Electric convection-ovens
The kitchen changes continuously
Cooking equipment has become faster, precise and versatile over the last couple of years. The expectations of efficiency and quality improvement keep getting higher. It is not a coincidence that especially Beuk Horeca, as a specialist on the ground of professional kitchen-equipment, recommends you the BEUK Turbo-Economic. To be used like you prefer from haute cuisine to fast food restaurant. From bakery to butchery. The BEUK Turbo-Economic is available in three models. Whatever type you choose, they work excellently alone but they are also the recipe to succes when used in a team. The Beuk Turbo-Economic combines speed and versatility to prepare several quick and tasty dishes at the same time, this makes the Beuk Turbo-Economic the ideal oven. The oven is compact, easy to use, quickly on the right temperature and prevents flavour transfer between the dishes. That is why the Beuk Turbo-Economic oven is in particular appropriate for restaurant kitchens, company cafeterias and fast food restaurants but also perfect for making tasty flavoured meat in the butchery, supermarket, bakery or croissants. With that, the Beuk Turbo-Economic is by far the most versatile and accessible oven in its class/kind Customer friendly The Turbo-Economic is an ideal instrument to regulate the workload. You can prepare the dishes in a quiet period, and in the busy hours you use the Beuk Turbo-Economic. You can prepare different/several dishes at the same time, without taste or flavour transfer. Result: optimal efficiency in the kitchen, fast serving time and satisfied customers. Easy to use The Turbo-Economic is very easy to use. The users friendly control panel does not leave you with any other questions about it. Cleaning the oven is as well 'a piece of cake'. Thanks to the round oven corners and a smooth emaille surface you finish to clean the oven in the neck of time. No level-differences The Turbo-Economic deliverers culinary top performances. The special turbo-fan takes care of an optimal circulation of the hot air. This makes sure that you use the maximum of the oven space. You will be confident about each dish you cook no matter which level you choose to use, all of your dishes will become evenly done and brown. Weight in the meat dish If you cook meat frequently, the Beuk Turbo-Economic with its core-temperature meter is an understandable option. You enter the prefered core-temperature on the oven and it will complete your request without any questions. If necessary superfast or on a very low rate with a minimum burn-out loss. With the use of the core-temperature meter is the roasting-proces completely controllable. You will hear a warnings signal when the core-temperature is reached. The Turbo-Economic will turn off automatically when the prefered core-temperature has been reached.

Safe and economical Thanks to the thick walled isolation and the double oven window the BEUK Turbo-Economic is very quick on temperature. Besides, these facilities make the oven safer and energy efficient when in use. The oven satisfies understandable on all safety demands and norms. Everywhere on its place The BEUK Turbo-Economic is only 74 cm wide and it is possible to assemble it on the wall because of its wall console. No need for the use of extra facilities, the use of an 230 Volt electric socket satisfies as an energy-supplier. Cleaning the oven is no problem at all. The BEUK Turbo-Economic oven is covered in solid stainless steel and has an extra smooth, easy to clean, emaille inside. Attention for de user The accessibility and the practical ease of use of the BEUK Turbo-Economic are unprecedented. Every detail is adjusted to that, like for example the door. The door can be opened up to 180 C which makes everything optimally accessible. Models The BEU5205K is just like the BEU5185K a hot air oven. Although its extra provided with a grill-element. The salamander/grill makes your BEUK Turbo-Economic an handy 2-in-one oven. With this optional grill you can cook au gratin and grill quickly. The salamander has a royal working space and a grill power of 3 kW. De BEU5255K has just like the BEU5202K a grill-element, next to that is the oven equipped with a core-temperature function.

BEU5185K

optimal control

Easy to adjust

Core-temperature meter
Salamander / grill BEU5205K & BEU5255K
Content Power kg Capacity Size (wxdxh) kW Volt

*BEU5185K*

2 grids 740x580x560 Hot air 5 levels 450x360x320 3,0 24

1.664,-

*BEU5205K*

BEU5205K

740x580x560
Hot air salamander / grill-element
2 grids 450x360x320 3,levels 230 25

1.738,-

*BEU5255K*

BEU5255K

Hot air 2 grids 740x580x560 salamander / grill-element 5 levels Core-temperature meter 450x360x320 3,0 25

2.035,-

Stainless steel wall frame for upper ovens
Convection-ovens Electric bake-off ovens
Picture Model Size mm (wxdxh) Description
Content Power Capacity Size (wxdxh) kW Volt

*BH310021*

BH310021

740x580x470

Temperature adjustable up to 260 C (without waterconnection)

3 grids

400x400 mm

3,5 230

2.995,-

*BH310030*

BH310030

940x580x470

Temperature adjustable up to 260 C provided with waterconnection R

2 grids

600x400 mm

3.210,-

*BH510063*

BH510063

930x820x670

5 grids

600x400 mm 12,8 400

5.760,-

*BH810064*

BH810064

930x820x940

8 grids

600x400 mm 15,8 400

6.660,-

Easy in use Digital time clock up to 90 minutes with buzzer Temperature adjustable up to 260 C Automatic liquid-injection Extra heavy heating-elements High quality stainless steel constuction Double glass door Autoreverse fan Heavy door-closure Optional deliverable with: Digital service or computer driven control base (movable) Extractor
Compact steamoven Compact steamoven
Description Temperature adjustable from 50 up to 100 C

*BSTM4G*

BSTM4G

495x460x395

1 adjustable grid to be used for build-in watertank also with solid waterconnection

2,0 230

1.180,-
Because of the very compact sizes you can place this little steam oven anywhere you prefer, even in the smallest places. Completely made of stainless steel. Provided with a integrated removable water tank (1 litre) which contains enough water to steam continuously on 100 C for at least 60 minutes. The oven is in less than 3 minutes from cold water on temperature to be able to steam. Also provided with build-in waterconnection. Electronic time clock adjustable from 1 up to 120 minutes. Digital temperature adjustment from 50 up to 100 C Removable grids for easy cleaning Easy control panel with a clear digital display Low-energy, uses only 2 kW Ideal for defrosting and regenerating of several fish species (because of low-pressure in the oven(room) makes it possible to prepare fresh fish species).

Microwaves Microwaves

Picture Model Size mm (wxdxh) Measurements mm (wxdxh) Description

kW Volt kg

20 memory settings
1000 W high 500 W medium interval 100 W low interval 340 W defrost interval 1,18

11 variable cooking controls

*R-15AT*

R - AT

520x406x309

351x372x211
pre-programmed programs 10 times not qualified for continuously proffesional use Content: 28 litre
2100 W high 1050 W medium interval 340 W Low interval 170 W Defrost interval 3,33

*R-25AM*

R-25AM
4 variable cooking controls

510x470x335

330x330x180
mechanical control panel Content 20 litre

1.308,-

2100 W high

*R-25AT*

1050 W medium interval 340 W low interval 170 W defrost interval 3,33
pre-programmed programs Content: 20 litre

1.410,-

*BR-INF*

BR-INF

Stainless steel frame
R-15AT Semi-professional microwave in- and external stainless steel implemented with an innerspace of 28 litre. Electric control 1000 Watt delivered power Express defrost function Double quantity function 20 memory settings 11 variable cooking controls 10 pre-programmed programs time-setting up to 30 minutes
1 microwavetube medium duty
R-25AM Pro Semi-proffessional microwave in- and external stainless steel implemented with a innerspace of 20 litre. mechanical control panel repeat-function 2100 Watt delivered power 4 variable cooking controls time-setting up to 30 minutes airfilter on frontside

2 microwavetubes compact

R-25AT Semi-professional microwave in- and external stainless steel implemented with a innerspace of 20 litre. Electric control repeat-function 2100 Watt delivered power Double quantity function 20 memory settings 11 variable cooking controls 10 pre-programmed programs time-setting up to 30 minutes
Picture Model Size mm (wxdxh) Size inside mm (wxdxh) Description

1000 W High

*NE-1027*

NE-1027

Mechanical settings,
500 W medium 1,W Low 340 W defrost 230 17,8

510x360x306 330x330x200

Max 30 min content: 22 litre

1.087,-

10 memory settings
1000 W High 500 W medium 340 W defrost 1,17,8

*NE-1037*

NE-1037
3 times, 3 steps, timer max 99 min content : 22 litre

1.190,-

*NE-10INF*

NE-10INF

combi-microwaves
1350 W high + 1840 W grill + 1800 W convection 3,W medium 420 W low 180 W defrost 230 41,0

*NE-C1475*

NE-C1475

99 memory settings

600x484x374 406x336x217
11 power levels content : 30 litre

3.890,-

*NE-14INF*

NE-14INF

NE-1027 Semi-professional microwave-oven of 1000 W. This Panasonic NE-1027 is ideal for snack sale places for example offices, stores, hospitals, etc and next to this THE solution for self-service situations when you want to warm up light snacks quick and evenly. Because of its stainless steel and ergonomic design is this microwave-oven perfect for keeping it clean. The oven is very easy to use and hygienic because of the flat bottom (no turning-plateau)
1 microwave tube medium duty
NE-1037 Semi-professional microwave-oven of 1000 W. This Panasonic NE-1037 is ideal for snack sale places for example offices, stores, hospitals, etc and next to this THE solution for self-service situations when you want to warm up light snacks quick and evenly. Because of its stainless steel and ergonomic design is this microwave-oven perfect for keeping it clean. The oven is very easy to use and hygienic because of the flat bottom (no turning-plateau) This oven has also 10 memory settings, besides the standard microwave functions. Touch-control 3 power levels from 340 up to 1000 W 10 programmable buttons Double quantity function Acoustic alert
NE-C1475 Professional combi-microwave-oven with a 1350 W microwave power and 1800 W convection power. Because of its stainless steel and ergonomic design is the Panasonic NE-C1475 perfect to keep clean. The oven can use the three functions (microwave, convection and grill) individually, but a combination of microwave-convection or microwave-grill is also possible. The convection-function is adjustable in temperature in steps of 10 C between 100 C and 250 C and can also cool down when you use the cooling-button. The unique defrost-system begins with a high power of 350 W and switches automatically to the low power of 140 W to prevent the dish from dehydrating. Electronic control panel with touch-control and turn-button Convection oven adjustable from 100C up to 250C 2 conductors for grids Prewarm 170 C / 210 C / 240 C (maximum of 4 hours) 99 memory settings Accelerated back-cooling for baking on low temperature and cleaning Acoustic alert

2 microwavetubes grill element, convection
pro-i heavy duty / compact size
Picture Model Size mm (wxdxh) Size mm (wxdxh) Description

*NE-1646*

NE-1646

Mechanical settings

1600 W high

422x508x337 330x310x175

timer maximum 30 minutes Content: 18 litre

800 W medium

2,6 230

1.960,-

340 W defrost

*NE-1656*

NE-1656
3 time settings, 3 power settings,

*NE-2146*

NE-2146

timer maximum 30 minutes

1050 W medium

3,2 230

2.331,-
2 levels cooking Content: 18 litre

*NE-2156*

NE-2156

2.480,-

2 levels cooking content: 18 litre

*NE-21INF*

NE-21INF
NE-1646 Professional microwave-oven with a power level of 1600 Watt. Because of its stainless steel and ergonomical design makes it perfect to keep the Panasonic NE-1646 clean and the double microwave tubes (up and down) makes warming up the food so well dosed that it becomes a qualitative better product and saves time. Mechanical control Adjustable power level from 340 up to 1600 W Time-clock Adjustable power button
NE-1656 A professional microwave-oven with a power of 1600 Watt. Because of its stainless steel and ergonomic design makes it perfect to keep the Panasonic NE-1646 clean and the double microwave tubes (up and down) makes warming up the food so well dosed that it becomes a qualitative better product and saves time. The oven is also implemented with 20 memory settings Touch control 3 power levels from 340 up to 1600 W 10 memory settings Double & triple quantity function Acoustic alert
All models: 2 microwave-tubes compact NE-2146 Professional microwave-oven with a power of 2100 Watt. Because of its stainless steel and ergonomical design makes it perfect to keep the Panasonic NE-2146 clean and the double microwave tubes (up and down) makes warming up the food so well dosed that it becomes a qualitative better product and saves time. Mechanical control Adjustable power level from 340 up to 2100 W Time-clock Adjustable power button
NE-2156 A professional microwave-oven with a power of 2100 Watt. Because of its stainless steel and ergonomic design makes it perfect to keep the Panasonic NE-2156 clean and the double microwave tubes (up and down) makes warming up the food so well dosed that it becomes a qualitative better product and saves time. The oven is also implemented with 20 memory settings Touch control 3 power levels from 340 up to 1600 W 10 memory settings Double & tripple quantity function Acoustic alert

Picture Model Size mm (wxdxh) Inner measurements Description mm (wxdxh)
pro-ii heavy duty / 1/1 gastronorm size

Power kW Volt kg

1800 W high 900 W medium 3,W low 340 W defrost 230 54,0

*NE-1840*

NE-1840

650x526x471 535x330x250

3.950,-

Content: 44 litre

16 memory settings
1800 W high 900 W medium 3,2 54,0 230

*NE-1880*

NE-1880
3 time settings 3 power settings

4.345,-

170 W low 340 W defrost
2100 W high 1050 W medium 3,W low 340 W defrost 400 54,0

*NE-2140*

NE-2140

4.180,-

3200 W high 1600 W medium 5,W low 340 W defrost 400 65,0

*NE-3240*

NE-3240

4.975,-

*NE-32INF*

NE-32INF

Stainless steel framework
The Panasonic PRO-II series contains 4 models with an inner space of 44 litre. The possibility through a ceramic middle-plate to divide the inner space in 2 compartments. Without problems you can fit four plates of 26 cm, 24 soup bowls or 2 x 1/1 GN plates in these microwave-ovens. The application of four microwave-tubes two up and two down, give the results of a very equal heatings patern. With the advantage of time saving and a qualitative better dish.
PRO-II HEAVY DUTY / 1/1 GASTRONORM SIZE
4 Microwave tubes Gastronorm
THE professional microwave-oven wich has the unique application to cook on 2 levels. Through the use of 2 microwave-tubes on each level and 1800 Watt power makes it possible to warm up evenly on a high tempo, this makes a qualitative better product and saves time. Because of its stainless steel and ergonomic design is the Panasonic NE-1840 perfect to keep clean. Mechanical control Adjustable power levels from 170 up to 1800 W Time-clock adjustable power button
THE professional microwave-oven wich has the unique application to cook on 2 levels. Through the use of 2 microwave-tubes on each level and 1800 Watt power makes it possible to warm up evenly on a high tempo, this makes a qualitative better product and saves time. Because of its stainless steel and ergonomic design is the Panasonic NE-1880 perfect to keep clean. This oven also has 8 programmable pre-prefered buttons wich you can use 2 times, this makes sure you can use the oven quick and easy. Touch control 4 power levels from 170 up to 1800 W 8 memory buttons
THE professional microwave-oven wich has the unique application to cook on 2 levels. Through the use of 2 microwave-tubes on each level and 2100 Watt power makes it possible to warm up evenly on a high tempo, this makes a qualitative better product and saves time. Because of its stainless steel and ergonomic design is the Panasonic NE-2140 perfect to keep clean. Mechanical control Adjustable power levels from 170 up to 2100 W Time-clock adjustable power button

THE professional microwave-oven wich has the unique application to cook on 2 levels. Through the use of 2 microwave-tubes on each level and 2100 Watt power makes it possible to warm up evenly on a high tempo, this makes a qualitative better product and saves time. Because of its stainless steel and ergonomic design is the Panasonic NE-3240 perfect to keep clean. Mechanical control Adjustable power levels from 170 up to 2100 W Time-clock adjustable power button
Microwaves Specifications

microwaves

Specifications
Model High Middle Delivered Low power Defrost Stand-by Quartz grill Hot air Combination functions Digital controls Cooking time memory Programmable programs Ext space Electric timer Hinge side Sound signal Ammount of Microwave tubes Airfilter front Stackable Errors report Company teller Spacing in Stainless steel Content preparing room Inside size (WxHxD) Outside size (WxHxD) Used power AC Weight
1000 Watt 1000 Watt 100 Watt 340 Watt/Interval
1000 Watt 500 Watt/Interval 500 Watt 340 Watt/Interval
1350 Watt 650 Watt/Interval 420 Watt/Interval 350-140 Watt/Interval Yes 1170 W / 1500 W /1800 W 1800 Watt (100-250C) Combination microwave and grill or hot air oven Yes
1600 Watt 800 Watt/Interval 340 Watt/Interval
2100 Watt 1050 Watt/Interval 340 Watt/Interval
10 function keys/ free programmable

99 pre-set programs

10 program keys/ 10 free keys.
20 function keys/ free keys
3 time settings 3 power settings Max 99 min. Leftside Yes 1 microwave tube 1000 Watt Yes Yes 22 Litre 330 x 200 x 330 mm
3 time settings 3 power settings Max 240 min. Leftside Yes
3 time settings 3 power settings Max 30 min. Leftside
3 time settings 3 power settings Yes Max 30 min. Leftside Yes
Max 30 min. (Mechanical) Leftside 1 microwave tube 1000 Watt Yes 22 Litre 330 x 200 x 330 mm

Max 30 min. Leftside

Yes Max 30 min. Leftside Yes
2 microwave tubes 675 Watt
2 microwave tubes 800 Watt
2 microwave tubes 1050 Watt
Yes Yes 30 Litre 406 x 217 x 336 mm
Yes Yes Yes Yes 18 Litre 330 x 175 x 310 mm
Yes Yes Yes Yes Yes 18 Litre 330 x 175 x 310 mm
510 x 306 x 360 mm 1490 Watt 230 V/50 Hz 17,8 kg
600 x 374 x 484 mm 3300 Watt 230 V/50 Hz 41 kg
422 x 337 x 508 mm 2600 Watt 230 V/50 Hz 30 kg
422 x 337 x 508 mm 3160 Watt 230 V/50 Hz 30 kg

Accessories

2 sliding runners 1 grid 1 ceramic plate

1 ceramic plate

manufacturer

Microwaves

1800 Watt 900 Watt/Interval 170 Watt/Interval 170 Watt/Interval
1800 Watt 900 Watt/Interval 340 Watt/Interval 170 Watt/Interval Yes
2100 Watt 1050 Watt/Interval 340 Watt/Interval 170 Watt/Interval
3200 Watt 1600 Watt/Interval 340 Watt/Interval 170 Watt/Interval

R-15AT

1000 Watt 500 Watt/Interval 100 Watt/Interval 340 Watt/Interval Yes

R-25AT

2100 Watt 1050 Watt/Interval 340 Watt/Interval 170 Watt/Interval Yes
16 function keys/ vrij programmable
20 function keys/ 10 preprogrammed

3 tijden en 3 steps

10 steps
Yes Max. 60 min. Under Yes
Yes Max 60 min. Under Yes
Yes Ma. 60 min. Under Yes

Max 30 min. Left side

4 microwave tubes 450 Watt
4 Microwave tubes 450 Watt
4 Microwave tubes 525 Watt
4 Microwave tubes 800 Watt
Yes Yes Yes Yes 44 Litre 535 x 250 x 330 mm (1/1 GN) 650 x 471 x 526 mm 3200 Watt 230 V/50 Hz 54 kg
Yes Yes Yes Yes 44 Litre 535 x 250 x 330 mm (1/1 GN) 650 x 471 x 526 mm 3650 Watt 400 V/50 Hz 54 kg
Yes Yes Yes Yes 44 Litre 535 x 250 x 330 mm (1/1 GN) 650 x 471 x 526 mm 4960 Watt 400 V/50 Hz 65 kg
Yes Yes Yes 28 Litre 351 x 372 x 211 mm
Yes Yes Yes 20 Litre 330 x 330 x 180 mm
Yes Yes Yes Yes 20 Litre 330 x 330 x 180 mm
520 x 406 x 309 mm 1600 Watt 230 V/50 Hz 18 kg
510 x 470 x 335 mm 2900 Watt 230 V/50 Hz 33 kg

1 Ceramic plate

Salamanders Infra salamanders with lift

high-lite

Picture Model Size mm (wxdxh) Grill Surface mm (wxdxh) Grid Lift Heath zones Power kW Volt

*SRH0505*

BHRS0505

400x450x500

340x300
Hood, stairless adjustable between 40/190mm.

3,0 230

2.075,-

*SRH2011*

B H R S 11

570x530x500

550x370

4,5 400

*SRH1010*

BHRS1010

735x530x500

710x370

6,0 400

3.635,-

High-lite salamanders
Stain solid steel * Three models with: 2,3 or 4 elements * Within 6 seconds on (company)temperature * Energy savings from approx. 65% to the aspect of standard salamanders * No extra (heat/warmth)-source in your kitchen * Only use when you need to * Digital timer with memory-function * Automatic turn-off with acoustic alert * User-friendly * Complete or parts of heating as you prefer adjustable * In height adjustable hood?

SRH1010

S R H 11

SRH0505

High-Lite - Auto-Start Function - Cook & Hold

BSRH2060

* Stainless steel * Three or four elements * Within 6 seconds on (company)temperature * Energy savings from approx. 65% to the aspect of standard salamanders * No extra (heat/warmth)-source in your kitchen * Only use when you need to * Digital timer with memory-function * Automatic turn-off with acoustic alert * User-friendly * Complete or parts of heating as you prefer adjustable * In height adjustable hood * Starts an automatic program when a plate or scale is placed * Cook & hold function

Grill surface mm (wxdxh)

Heath zones

power kW Volt

*BHRS2060*

BHRS2060

3.520,-

*BHRS1060*

BHRS1060

4.305,-

Salamanders Ultra rapid salamanders

timer: 0 sec. - 30 min.

Picture Model Size mm (wxdxh) Grill surface mm (wxd) Grid Heath zones Power kW Volt kg

*8134011*

540x420x390

380x390

*8134012*

8134012

790x420x390

630x390

1.068,-

Stainless steel 18/10.

The ceramic salamanders have special heating elements that gets salamanders very quickly to the desired temperature and within 20 seconds use. Together with the ceramic glass, which also features shielded against dirt, salamanders, those for a smooth and unique grill effect. The salamanders have a 30 minute timer and continuous mode. Standard version with drip tray and heavy chromed grill.
AISI 18/10 RVS Heating time: 20 sec. Heating equally Heating elements with ceramic safety guard
Salamanders salamanders with lift

Salamanders with lift

8134006

8134005

Housing from stainless steel 18/10. Because of the adjustable levels the grill-height is variable. The down reflecting heat-beams take care of an unique grill-action. Standard model with leak-container and heavy chromed grid. Model 8134006 is provided with two independently adjustable temperature-switches. Incoloy protected heating elements easy to clean. Elements are easy to clean.

*8134005*

400x350

Hood stepless adjustable

1.060,-

*8134006*

600x450x500

600x350

4,0 400

1.255,-

accessories

hanging frame

*BESALFRA*

BESALFRA

Stainless steel frame for the salamander, custom-made

Salamanders Salamanders

Without lift
Picture Model Size mm (wxdxh) Grill surface mm (wxd) Grids Heath zones Power kW Volt kg

*8133007*

8133007

670x340x360

3 heating-elements 2 grids internal measurements: 540x300x300

*8133006*

8133006

670x340x270

2 heating-elements 1 grid

*8134007*

8134007

540x400x390

380x380

*8134008*

8134008

790x400x390

630x380

Salamanders

8134007, 8134008,
Stainless steel 18/10. The infra-red beam-elements are being served through the use of a step less adjustable control-button. The heavy chromed working-grid can be placed on three different grill-heights. The grease-collection container is removable. The model 8134009 is for two independent functioning heating-zones.
Stainless steel. Provided with 2 separately adjustable incoloy protected under- and upper elements. The elements can be switched on how you prefer, through the time-switch, or through the headswitch. The timer is adjustable from 1 until 15 minutes. The toaster is provided with one removable grid, which can be adjusted in height. Provided with removable stainless steel greasecollection container. The warm-up time amounts 90 seconds.
Stainless steel. Provided with incoloy protected under-, middle- and upper element. These elements can be switched on together or separately. through the time-switch, or with/by the use of the head-switch. The timer can be adjusted from 1 until 15 minutes. The toaster is provided with two removable grids. Provided with removable steel grease-collection container. The warm-up time amounts 90 seconds.

Adjustable in height

0521702 0521701

0521704

Grill surface mm (wxd)

*0521712*

0521701

560x350x370

480x350

3 levels (no lift.)

2,5 230

1.085,-

*0521702*

0521702

800x400x314

530x325

5 levels

1.995,-

*0521704*

680x430x410

stepless in height adjustable 160 mm.

2.710,-

hinged

*BESLFR*

BESLFR
Stainless steel frame for the salamander, measure-work
Fast-food finisher Thermo-finisher
FA S T- F O O D F I N I S H E R S
The ideal device for fast warming of dishes or garnis of union soup, also usable for melting cheese and toppings. Grilling of bread or warm sandwiches, The warming of pizzas. chicken-wings, nachos and so on. The Hatco thermo-finisher is a lot faster then conventional methods and with less stress people would get a great result. The Thermo-finisher saves energy when its on stand by in the quieter moments. Easy to use and to clean. One of our sales representatives will gladly answer any of your questions.