Audio microphones and mic accessories
Microphones Microphones are designed to pick up sound in a certain way, and can be classified accordingly; Omni-directional Will pick up sound equally from a 360 degree circle around it. It is of most use when placed amongst a group of people, on a table at a meeting for instance. Cardioid Will pick up sound mainly from the direction in which it is pointed. This is almost always the type of microphone that is fitted as standard to your camcorder. Super cardioid Similar to the cardioid, but has a narrower field of response and so is more directional. Sometimes referred to as shotgun microphones, these are the most common accessory type of microphone, bought to supplement the camcorders own microphone. Hyper cardioid A fairly specialised piece of equipment that has an even narrower response field than the super cardioid. Stereo Most people change microphones because they want a different response pattern to that of the on-board microphone. To go very directional it is difficult to preserve a stereo image as both left and right elements pick up sound at the same time. To get a directional response with a stereo camcorder choose a mono microphone and use a stereo to mono conversion lead. The other main reason for using an off-camera microphone is to defeat motor noise, in which case choose a stereo microphone to maintain the soundstage. Other microphone groups include: Tie clip A very small and unobtrusive microphone, designed to be attached to a tie or lapel. The microphone is connected to a small battery holder which will fit easily into a pocket, and this is in turn connected to the camcorder by a good length of cable (usually ft). They have a number of uses; to add commentary at the time you are filming, to position on string or key instruments, or for interview type situations. Radio microphone Consists of a matching radio transmitter and receiver. The transmitter has a socket which will accept either the tie clip microphone provided with the unit, or if you prefer, a separate microphone can be used. The receiver plugs into the microphone socket on the camcorder. The bees knees of add-on microphones. Specification: Frequency response 150Hz17kHz Impedance 200 ohm Weight excl cable 60g approx Sensitivity in free field, no load (1kHz) 16mV/Pa 2.5 dB Equivalent noise level weighted as per CCIR 4683 28dB Equivalent noise level 18dB Dimensions: 230 x 65 x 50mm Power supply 1 x SR44 (included) approx life 200hrs use [MKE300] 149.99 Special offer: Buy MKE300 plus matching Rycote Special 190 windgag together and save s [MKDEAL] 159.99

Audio microphone pre-amps & adaptors
VIVANCO MA222 MICROPHONE PRE-AMP.
Allows microphones to be connected to an amplifiers line input. An adjustable impedance control allows matching for almost any microphone. Input sockets are 2 x 6.3mm with mono/stereo changeover switch. Supplied with UK mains adaptor. Dimensions 118 x 30 x 55mm. [MA222]
Battery operated microphone pre-amps MB7 microphone pre-amplifier
This allows a mono microphone to be connected to an amplifier (or tape deck etc) with a phono line input. The input is a 6.3mm jack socket and the output is fed equally to the 2 phono line outputs making easy connection to stereo equipment. It has a high 40dB gain and very low noise. It is powered by a 9V PP3 battery, which is switched off automatically when you unplug the mic. Microphone pre-amp MONO [MB7]
Microphone windgags Windgags for external microphones
The professionals answer to wind noise. A model to fit most microphones. Complete with elasticated base and Velcro fastenings.
Windgags, Mic pre-amps & adaptors

Standard mini windjammer

Model Max diameter Small 3cm Extended small 3cm Special small 4cm Medium 4cm Extended medium 4cm Large 4cm Max length 3cm 5cm 4cm 6cm 7.5cm 10cm [Order Code] [RWS] [RWES] [RWSS] [RWM] [RWEM] [RWL] Price 21.99 21.99 21.99 22.99 22.99 22.99
MB8 microphone pre-amplifier
This is allows a stereo microphone to be connected to an amplifier (or tape deck etc) with a stereo phono line input. The mic input is a 6.3mm jack socket (an adaptor could be used for 3.5mm mic jacks) and the gain is 40dB. The power supply is a 9V PP3 battery, which is switched off automatically when you unplug the mic. Microphone pre-amp STEREO [MB8] 69.99

Special windjammer

Designed with the professional in mind these use an especially long 3cm synthetic for maximum effectiveness.
Model Special Special Special Special Special Special Special Special Max 90 (pictured) 190 diameter 5cm 5cm 5cm 5cm 5cm 5cm 5cm 5cm Max length 6cm 8cm 9cm 10.5cm 13cm 15.5cm 16cm 19cm [Order Code] [SPEC60] [SPEC80] [SPEC90] [SPEC105] [SPEC130] [SPEC155] [SPEC160] [SPEC190] Price 21.99 21.99 21.99 21.99 22.99 22.99 22.99 29.99

Video editing

Hama Easycut
A simple-to-use edit controller with built in audio mixer, giving you an easy way to cut all your unwanted footage, rearrange the scenes and add music or commentary. Very easy to use, with onscreen displays and full instructions. Compatible with all Control-L LANC and Panasonic 5 pin and 11 pin camcorders it has a 192 scene memory with options of straight cut, fade to and from white or STAND ALONE LINEAR black transitions. Connections are: Player (source machine) 3 x RCA phono plus s-video; Auxiliary audio input 2 x RCA phono; Mic input 2 x 3.5mm jack sockets (for L & R); Recorder (destination machine) 3 x RCA phono plus s-video; Player and Recorder control jacks; 2.5mm stereo headphone jack. Includes UK power supply, 1 x LANC cable, 1 x Panasonic 5 pin cable, 1 x 3 phono 3 phono cable, 1 x 2 phono - 2 phono cable, 1 x IR wand, 1 x commentary microphone, 1 pair stereo headphones and instruction manual. Originally 185.00 [HEC] 39.99

Datavideo SE-200

Combines an audio mixer (3 stereo channels with LED metering), colour processor (RGB control with joystick, colour saturation and brightness), special effects generator (24 different wipe patterns with T-bar control), colour titler (3 fonts, 4 text sizes, eight background colours plus video, 24 characters per line, 11 lines per page, 2600 STAND ALONE LINEAR character/110 line memory, text can be wiped, scrolled or crawled at varying speeds), and edit controller (can control two source decks and one record deck. Memory holds up to four EDLs each up to 99 scenes, RCTC and VITC compatible). Can be combined with the TBC 2000 or TBC 3000 time base correctors to give two source A/B edit control with cross-fades, rolls and dissolves Supports RCTC, VITC and GPI triggers. Connections info: Player 1 and 2 connections each 3 x RCA phono + 4-pin S-video, GPI trigger socket, IR socket, 2 x LANC sockets, aux. in 2 x RCA phono, 3 x RCA phono + 4-pin S-video recorder connections, DC power socket Included: Microphone, UK power supply, IR wand, 2 x Pana control cables, JLIP control cable, 2 x LANC control cables, Instruction manual, instructional video (VHS) [SE200] 229.99 Source machine Where the signal is coming from. Most commonly a camcorder, but could also be another VCR. Destination machine Where the signal is being sent. Most commonly a VCR or TV.

Composite to S-video adaptor/connector
Phono plug to s-video socket adaptor. Useful for converting s-video to composite video. (If you need to convert composite to s-video we recommend the Keene STOC (above) which has passive filtering for better results.) [KA162]

RGB TO S-VIDEO CONVERTOR

RGB is a great method of sending video, with picture resolution as good as s-video and vastly superior to a std composite signal. The problem is not everything can accept an RGB signal and often composite is your only option. Well, here's another problem solved! This Box converts the RGB scart output from Sky Digital/OnDigital boxes and DVD players into S-video plus audio. Its ideal for making high resolution connections to AV amplifiers, SVHS/DVHS recorders and Plasma screens.
[RGB2S] 59.99 BULK PRICING (50+) and OEM AVAILABLE on this product
Component video to RGB transcoder
The Kramer FC-12E (pic shows both front and rear panels) is a high quality format converter designed to transcode between component video (Y, R-Y, B-Y) as coming from say a DVD player, and the RGBS Scart input of a TV or a video monitor. The FC12E can pass through standard video (to and from a Scart equipped VCR), as well as toggle the TV between video/RGBS/RF modes. The usual Kramer build quality applies. Technical Specifications INPUTS: 1 component video - (Y, R-Y, B-Y) 1V, 0.7V, 0.7Vpp/75 ohm on BNCs. 1 audio stereo 1Vpp/50 k nom. on RCAs. OUTPUTS: RGBS on a Scart type connector, with video/audio pass through. BANDWIDTH: 20 MHz -3dB MAX. VIDEO LEVEL: 2.1 Vpp. NON LINEARITY:0.3% S/N RATIO:>69 dB. CONTROL:VCR/DVD selector switch, AV/RF selector switch DIMENSIONS: 22cm x 18cm x 4.5cm WEIGHT:1.3 kg POWER SOURCE: 12 V DC, 500 mA (UK adaptor supplied) [FC12E] 239.99
RGB explained: www.syncblaster.com
See also Leads and Cables RGB and component video cables
RGB answers: www.syncblaster.com
Keene RGB2C RGB/Component video transcoder
Another in-house product from KE Keene Electronics, the RGB2C can convert an RGB input to a component (Y Pb Pr) output, and vice versa. It can cater for sync on green or composite sync input and also provide sync on green or composite sync output. LED indicators provide useful information on the type of signals present and which process is being performed. Designed to be installed in-line with the signal path, has SCART input and output connectors to make connection simple. Supplied complete with UK mains adaptor and KA150 scart to 3 phono adaptor. [RGB2C] 89.99 BULK PRICING (50+) and OEM AVAILABLE on this product Also available with 2m output connecting cable: RGB2C as above plus 2m output cable scart to 15 pin HD plug [RGVGA] 110.00 RGB2C as above plus 2m output cable scart to 5 x phono plugs [RGRCA] 114.99 RGB2C as above plus 2m output cable scart to 5 x BNC plugs [RGBNC] 119.99 Component video connection kit for use with Optoma projectors This kit contains the Keene RGB2C convertor and a component video output cable to go straight to the 15pin HD connector on your Optoma projector. The RGB2C is designed to take an RGB scart input direct from say a digi-box or DVD player. For further technical details please see http://www.syncblaster.com [OPTAKIT] 99.99

Turn any monitor into a TV! A really useful device thats ideal for use with screens and projectors with a 15pin HD (computer) input. Basically it is a video switchbox that can line double (output to SVGA) and also incorporates a terrestrial TV tuner (analogue). You can use it to turn your display into a true multimedia centre by linking it to your DVD player, VCR, Camcorder, Game Console, satellite receiver or simply using it as a TV with the built in tuner. Theres also a pass-through connection for your PC. At time of writing 15 LCD monitors can be picked up for under 200 - just add this box and youll have yourself a 15 LCD TV for less than 300! Features: PAL PLUS mode for sharp-edged smooth moving pictures Accepts Composite and S-Video signals from any video source Scales up to 1024x728 (XGA) at 60Hz or 75Hz refresh rate Accurate auto-scan and advanced channel search function Fine-tune setting, stored per individual channel Channel swap and channel label function Pull-down detection and correction for film-based sources Sport and Static video mode Plug and play easy set up with on-screen display Inputs: RF signal from antenna or cable (UK PAL I); composite video (RCA); Audio (L & R RCA); S video; VGA 15 pin D type connector ; audio - headphone jack Outputs: VGA 15 D type connector; audio headphone jack Power cable AC adaptor with 12Vdc output Dimensions: 32mm x 229mm 150mm. Weight: 450 gm WHATS IN THE BOX? PV200, UK mains power supply, remote control, AV cables: 1 x 15pin HD male to 15pin HD female, 1 x 3.5mm st jack plug to 3.5mm st jack plug, 1 x 2 phono plugs to 2 phono plugs and 1 x single phono plug to single phono plug( composite video). You might also need a 15pin HD VGA male to male output cable to connect the PV200 output to your display eg [15HDPP02] or similar PLEASE NOTE - the internal tuner is compatible with the UK PAL-I system only! [PV200] 84.99
We accept payment by Visa, Mastercard, Switch, Solo and Delta
iScanHD video scaling processor and hub Video scalers

Self-standing PRO monopod MN682
Robust three-section aluminium professional monopod with the handy addition of three retractable legs. The 682 features a sure rubber grip, wrist carrying strap, quick action lever leg lock system with 45 flip, large 2.3" camera/head platform with plastic cover and dual 1/4"|3/8" camera screw. SPECIFICATIONS Material: silver aluminum Maximum height: 172 cm (67.7 in.) Minimum Height: 74 cm (29.1 in) Leg Sections: 3 Foot type: rubber Maximum load capacity: 26.4 Ib Weight: 1.1 kg (2.4 lb) [MN682] 69.99
MANFROTTO UNIVERSAL FOLDING MONOPOD BASE MN678
Turn your monopod into a self supporting stand! This unique accessory allows the addition of a base made of three foldable high strength steel legs for monopods 679, 680, 681 and old style 479, 434, 3249. The legs can be folded and stored inside the bottom section of the monopod ready for use in just a few seconds. SPECIFICATIONS Maximum Load Capacity: 13.9 kg (30.8lb) Weight: 0.4 kg (.9lb) [MN678] 34.99

MN676 MONOPOD

Four section, lightweight monopod with rapid action extension locks. Suitable for compact and 35mm cameras and smaller min-DV camcorders. 1/4" camera fixing screw. SPECIFICATIONS Maximum height with extended centre column: 154 cm (60.7in) Closed length: 48 cm (18.9in) Maximum load capacity: 4.5 kg (10lb) Weight: 0.4 kg (0.9lb) Black finish [MN676B] 24.99 62

Slik Mini tripod

A beautifully made miniature tripod from Slik. Weighing just 320g it has two-section legs to provide a maximum operating height of 215mm. Ideal for table top work or can be used on car roofs, walls etc when out and about. Especially suited to compact cameras, digital cameras and Palmcorders this tripod really is small and light enough to be carried anywhere and should easily fit into most gadget bags [SMT] 19.99
Tripods and video heads (continued) Manfrotto MN055 Professional tripod series MN055A
Lightweight portable and sturdy the 055A is a classic tripod, ideal for 35mm, medium format and video camera applications. The extra long centre column is reversible, allowing the camera to be supported underneath the tripod, ideal for macro & nature work. 3 section quick lock (twist type) legs with triangular centre column which eliminates rotation even when not fully locked. Like all Manfrotto kit the build quality is superb. Specifications Closed height: 61cm Minimum working height: 56cm Fully extended height: 137cm Fully extended with fully extended centre column: 181cm Weight: 2.2Kg Max rec. weight 6Kg [MN055] Also available in black finish [MN055AB]

TV AERIAL RF connection AV stereo audio AV video Signal direction VIDEO RECORDER
Connecting up a Surround Sound or AV system
So now you've bought yourself a Surround Sound AV (Audio Video) amplifier. The next step is to connect everything together. Let's assume that you have a VCR, a CD player, a DVD player, a satellite receiver and of course a TV. First, in order to remain reasonably user (family!) friendly, it's best to maintain the RF connections. So that's aerial into satellite receiver, satellite receiver out to VCR in, VCR out to TV in This completed, normal transmissions from BBC, ITV etc will be viewable on TV and recordable on the VCR. Perhaps you didn't know that when a satellite receiver receives a signal, or a VCR plays back a tape, the audio signal is available in stereo at the scart socket only. The RF aerial signal is mono, so if you watch a satellite channel on TV via the RF connections, the sound will be in mono, even if you've got a Nicam stereo TV! In order to get everything working in stereo or Surround Sound, the easiest approach is usually to use your AV amp as the heart of the system. The leads required. Typical leads for connections would be: 2 phono plugs to 2 phono plugs (eg Sterling Gold SG21/2/3/4), stereo audio link CD player to AV amp. If supported by both player and amp you could also make digital audio connections, either optical or coaxial SG91/92 or SG11/12 etc. Scart to 6 phono plugs, eg SG71/2/3/4, Scart on VCR to AV amp connection, stereo audio and video to and from VCR; 3 phono plugs to 3 phono plugs eg SG31/2/3/4, stereo audio plus composite video connection DVD or other AV source to AV amp. If supported by both player and amp you could alternatively use s-video connections SG42/42 etc; Scart plug (signal out of scart) to 3 phono plugs, eg SG61/2/3/4, stereo audio plus video connection satellite receiver to AV amp; 3 phono plugs to scart plug (signal into scart), eg SG61/2/3/4, stereo audio plus video connection AV amp to TV. If supported by amp and TV you could alternatively use s-video connections SG42/42 etc. It is worth using good quality cable, particularly on longer runs, and screened scart leads. Keene Sterling Gold cables are designed specifically for this sort of application. Their gold plated end connectors also stop the connection deteriorating with age. Note that this approach assumes that your TV has only the one AV (scart) input and so uses your AV amplifier as the hub of the system making for easy AV switching between devices. It is increasingly common for TVs to have multiple scarts and other AV sockets, and also for the devices themselves to have multiple outputs. This being the case we still advocate making the initial connections via the AV amp and then making whatever additional direct connections you are able to the TV, for example Satellite RGB scart to TV. It is also worth remembering that there is no strictly "correct" way to connect this equipment if you've come up with a different wiring method that works (ie you can view, hear and record what you like when you like) then great problem solved! If you'd like some help we will work out the leads you need. We need to know what connectors are on each piece of equipment, and the length each lead needs to be. Equipment model numbers are not much use for this it is the

Order code [SG11] [SG12] [SG13] [SG14] [SG15] [SG21] [SG22] [SG23] [SG24] [SG25] [SG202] [SG204] [SG205] [SG31] [SG32] [SG33] [SG34] [SG35] [SG41] [SG42] [SG43] [SG44] [SG45] [SG51] [SG52] [SG53] [SG54] [SG55]
Price 9.99 12.99 15.99 19.99 24.99 9.99 12.99 15.99 19.99 24.99 12.99 19.99 24.99 12.99 15.99 19.99 24.99 29.99 9.99 12.99 15.99 19.99 24.99 12.99 15.99 19.99 24.99 29.99
2 phono plugs to 2 phono plugs Stereo audio link eg VCR to TV or AV amplifier
3.5mm stereo jack plug to 2 phono plugs
3 phono plugs to 3 phono plugs Stereo audio plus video link eg VCR to VCR or AV amplifier
S-video plug to S-video plug Hi-8mm or S-video link eg Camcorder VCR to TV or AV amplifier Scart plug to Scart plug eg VCR to VCR or TV, satellite to TV
Scart plug to Scart plug Straight entry, flat cable
0.75m 1.5m 3.0m 5.0m 0.75m 1.5m 3.0m 5.0m 0.75m 1.5m 3.0m 5.0m
[SG51F] [SG52F] [SG53F] [SG54F] [SG61] [SG62] [SG63] [SG64] [SG71] [SG72] [SG73] [SG74]
14.99 19.99 24.99 29.99 12.99 15.99 19.99 24.99 15.99 19.99 24.99 29.99
Scart plug to 3 phono plugs (switchable in/out of Scart) eg VCR to AV amplifier
Scart plug to 6 phono plugs eg VCR to VCR
Scart plug to S-video plug plus 2 phono plugs, wired signal OUT of scart eg DVD player to AV amp, S-video VCR to TV Scart plug to S-video plug plus 2 phono plugs,wired signal IN to scart eg DVD player to AV amp, S-video VCR to TV Scart plug to S-video plug plus 2 phono plugs, signal switchable IN/OUT of scart eg DVD player to AV amp, S-video VCR to TV CoAx plug to coax plug, with ferrite interference suppressors. RF aerial lead CoAx plug to coax socket, with ferrite interference suppressors. RF aerial lead Toslink to Toslink optical
0.75m 1.5m 3.0m 5.0m 10.0m 0.75m 1.5m 3.0m 5.0m 10.0m 0.75m 1.5m 3.0m 5.0m 10.0m 1.5m 5.0m 1.5m 1.0m 2.5m 5.0m
[SG81] [SG82] [SG83] [SG84] [SG85] [SG81A] [SG82A] [SG83A] [SG84A] [SG85A] [SG81S] [SG82S] [SG83S] [SG84S] [SG85S] [SGA2] [SGA4] [SGA2A] [SG91] [SG93] [SG95]
15.99 19.99 24.99 29.99 34.99 15.99 19.99 24.99 29.99 34.99 15.99 19.99 24.99 29.99 34.99 6.99 9.99 6.99 14.99 19.99 24.99 75
RGB & Component video cables
Scart 3 x phono plugs. Application: RGsB or component video.
2.0m [SBB72] 5.0m [SBB74] 10.0m [SBB75]
SCART 15 PIN HD MALE RGB WIRED RGBs FOR SANYO. Suitable for use with Sanyo PLVZ1 projectors, chassis numbers Z1xx onwards. The connections are as follows Scart pin VGA pin Blue Screen Blue signal Green Screen Green signal Red screen Red signal 5 13

24.99 34.99 39.99

Special terms and conditions relating to made to measure leads
We will do our best to supply your lead quickly but it may on occasion take up to 14 days. We can only work to the nearest half-metre. We havent as yet found a way to shrink or stretch a lead so it is essential that you measure correctly. Faulty leads may of course be returned for repair/replacement but leads ordered in error will be subject to a 50% re-stocking charge. To avoid confusion please use order codes as per the example above. We will attempt to manufacture leads to other combinations but you may be asked to send confirmation of the connection details. Leads correctly supplied to your connection details may not be returned for credit or replacement. RGB Leads To Go: We're happy to make RGB wired scart cables to any configuration you like, and will connect them either as per your instructions, or via the most common method. We must point out that there is a lot of variation in the way the scart socket on the equipment itself can be configured. Similarly, the equipment you wish to connect to might be happy with the signal your scart socket delivers or it might require different or stronger sync levels. These results can be difficult to predict so please double check the configurations and specifications on each item before ordering a custom lead.
Home installation and DIY leads components
Loose cable 80 End connectors 82 Wall outlet plates 83 Modular switch & connector panels 84
Loose cable for home installations and DIY leads
Cable description/application Order code Reel /m /m length (m) (singles) (10m+) /reel (equals /m)

Audio interconnects

HQ screened stereo
Core thickness 2 x 0.14mm2, Core composition=2 x 18 x 0.1mm, colour=black, screening=individual, dimensions 3.0 x 6.0mm

[KBL5]

110.25 (1.10)
7 x 0.19mm copper conductor with high density polythene insulation, copper braided sheath and black PVC outer, overall diameter 5.8mm, capacitance 67pF/metre. Uses: video, digital audio. Single screened cable for general audio use, 7/0.2mm copper core, overall diameter 3.1mm, grey PVC sheath Stereo screened cable for general audio use, 13/0.2mm copper conductor, overall 2.5 x 5.5mm grey PVC sheath

RGB cable

A special cable for RGB signals, with 3 coaxial cores plus 2 twisted pairs. Ideal for RGsB, VGA, s-video, s-video plus composite or component video. Specifications: Construction: 3 x75ohm coaxials laid up around 2 x twisted pair conductors with overall screen and outer jacket. Outer Jacket PVC 8.9mm overall diameter, metre marked. Coaxes inner conductor 7 x 0.16mm; dielectric foamed polyethylene; screen tinned copper braid 96% optical coverage; Jacket PVC 3.3mm. Capacitance 62pf/m nominal Impedance 75 @ 200MHz nominal; Attenuation 2 dB/10m max @100 MHz. Twisted Pair: Inner conductor 7 x 0.16mm tinned copper wire 0.42mm; dielectric polyethelyne 0.85mm. Screen aluminium polyester tape with drain wire

New RGB cable

[KBL28]

240.00 (2.40)

[KBL29] RGB cable

309.00 (3.09)

A special cable for RGB signals with 5 coaxial cores. Ideal for RGB plus H & V sync. Can also be used for VGA, component, composite or s- video applications. Specifications: Each conductor is a 26 AWG, 75 ohm, coaxial conductor, colour-coded, and wrapped in a single jacket. Features Doubleshielded foil and copper serve to reduce interference, a ripcord to reduce cable damage during installation, stranded filler to maintain tight bundle & eliminate shift and twist and 5 colour-coded 26 AWG stranded coax conductors for easy identification of RGBHV. Capacitance 54.8pF/m nominal, impedance 75ohm@ 200MHz nominal, attenuation 17.6dB/100m 100MHz. Overall outer diameter 9.17mm bend radius 3.7cm.

[KBL30]

1050.00 (7.00)
GP screened cables for mic extensions, LANC extensions, IR wands etc

Screened stereo audio

Stereo screened cable for general audio use, twin 7/0.2mm copper conductors with lapped screening and cotton insulation, overall diameter 4.8mm, black PVC sheath

[KBL19]

103.50 (1.04)
See also Budget screened mono [KBL17] and budget screened stereo [KBL18]

GP non screened

Extraflex power cable, black Extraflex power cable, red 15 amp power cable
Very flexible single core wire, 55/0.1mm copper, overall 2.8mm, max current 6A. Black sheath Very flexible single core wire, 55/0.1mm copper, overall 2.8mm, max current 6A. Red sheath. TWO CORE 15 AMP CAPACITY WITH SOFT PVC JACKET, 3.3mm x 6.6mm
[KBL20B] [KBL20R] [KBL22]

0.34 0.34 0.52

0.30 0.30 0.50
6.30 (0.26) 6.30 (0.26) 38.85 (0.39)

Network

CAT5 network cable
Adaptors & connectors
CAT5E Unshielded twisted pair (UTP) cable 4 twisted pairs of 24AWEG solid conductor cable, conforms BS EN50173

[KBL23]

61.50 (0.21)

Coaxial cable clips

Nail-in securing clips for coaxial aerial cable, box of 100 [CC7] 2.99

Coaxial cable stripper

BASIC KIT

This kit, comprising the Keene IR Distribution Amplifier, 240V UK mains power adaptor, 1 x low power emitter wand (see output component [IRLPW] below), 1 x high power emitter wand (see output component [IRHPW] below) and instruction leaflet. Requires input device (not included). [IRBKIT] 34.99 BULK PRICING (50+) and OEM AVAILABLE on this product

INPUT COMPONENTS

Standard IR Receiver 40kHz suitable for most domestic equipment. [IRSR] 7.99 Wide Band IR Receiver Up to 100kHz for more esoteric equipment. [IRWBR] 12.99 Powermid IR lead To feed a Powermid RF receiver output directly to the IR Distribution Amp input (3.5mm stereo jack plug to 3.5mm stereo jack plug 1.2m long) [KLDE6] 5.99 Wavecom IR lead To feed a Wavecom RF receiver output directly to the IR Distribution Amp input (2.5mm stereo jack plug to 3.5mm stereo jack plug 1.5m long). [KLDE10] 8.99 Input splitter 1 x 3.5mm stereo jack plug to 2 x 3.5mm stereo jack sockets adaptor. Allows the IR Distribution Amp input to be fed by both a cabled feed (from say a Powermid RF receiver) and an inroom IR receiver. [KA109] 1.89

IR COMMANDER BASIC KIT

Comprises: Keene IR Commander 240V UK mains power adaptor 1 x high power emitter wand [IRHPW] 1 x instruction leaflet. [IRC] 99.99 BULK PRICING (50+) and OEM AVAILABLE on this product

OUTPUT COMPONENTS

Low Power Wand. Can be attached directly to the equipment facia or will work up to 4 metres away. Even when attached directly the equipment will still respond to external IR signals. Only to be used in the IR Distribution Amp low power output sockets. [IRLPW] 5.99 High Power Wand. Will operate equipment from up to 10 meters away. Can also be used in the IR Distribution Amp low power output sockets if required, but will then only perform as a low power emitter. Not suitable for one-to-one operation. [IRHPW] 7.99 Side Firing Wand. A short range emitter for direct attachment to the equipment fascia. [IRSFW] 7.99
Same IR receivers and input adaptors as for the Keene IR Distribution Amplifier, plus IR Commander FOUR INPUT EXPANSION MODULE The module is connected to the Commander by CAT5 cable and may be located up to 50m away. 4 receivers may be connected to this module. [IRC4A] 19.99

RF transmitter modules for use with the SC2800 Telephone Base Station
See SC2800 details above Also available (with other components) as part of the MS9700 security kit. KR21E Key Fob remote (for easy arm/disarm) [KR21E]
SM600 remote control (for full remote system control) [SM600] 24.99
GB10E glass break sensor [GB10E]
DS10E Door/window sensor [DS10E]

IR Command Centre

This unit lets you use an infra-red remote to control X10 modules. It is designed to be used with the universal X10 remote although of course you could also use this remote to "teach" any compatible learning remote such as the Pronto or Marantz RC5000 etc. As well as IR operation it also has its own keypad for direct push button control of up to eight devices. [IR7243]
MS10E PIR motion sensor [MS10E]

34.99 107

A multi-device remote control that can replace the IR remotes for up to seven other devices, It has a built in code library for all popular brands as well as a learning facility. Not only can it do all this, but it is also works as an X10 wireless (RF). transmitter When used with the TM12U transceiver module you can directly control up to 16 different X10 addresses with on/off and dim/bright. There's also an "all lights on" button which sends an immediate 'on' command to all lights set to the same house code (whether via a lamp module or a wall dimmer switch), particularly useful if there is a suspected intruder or one of those annoying 'bumps in the night'. There is also an 'all units off' function instructing everything connected to the house code to switch to the 'off' position. Powered by AAA batteries. Very simple and very useful. Note, for X10 use TM12U transceiver module required [UNIREM]

Remote control

An easy to use remote control, about the size of a cigarette packet. Can be used hand held, or attached to a wall. It can send an 'on' or an 'off' command to each of addresses 1 to 8 or 9 to 16 on a particular house code. In addition it allows a dim up or down to be carried out (which will be interpreted by a module or switch with dimming capability and will not affect any other item). RF signalling means that it does not have to be pointed at the unit to be controlled, but must be used in conjunction with the TM12U transceiver module, set to the same house code. The effective range is up to 30 metres., usually enough for the remote to address any item connected to the system form anywhere in the house. A small LED (which also acts as a battery indicator) illuminates when a signal is sent. Powered by AAA batteries. The combination of a remote control and transceiver being used to activate command groups set up by a computer interface model is extremely powerful and allows the user to take a high degree of control over electrical items in the home. More than one remote control can be used to send signals to a transceiver module and in practise many users find that one upstairs and one downstairs is often a sensible configuration. Note: TM12U transceiver module required [HR10] 24.99

ARC100 audio cassette cleaner

Hi-tech brush system

VHS-C/S-VHS-C cleaning cassette
Hi-tech brush system for perfect cleaning. Washable brush reaches even the tiniest head drum grooves. With cleaning fluid [VRC107] 7.99
8mm version of VRC01. Hi-tech brush system for perfect cleaning. Washable brush reaches even the tiniest head drum grooves. With cleaning fluid [VRC108] 9.99

[ARC100]

CD cleaner
By Vivanco, rotating cleaning cushion effectively cleans CDs. C/w fluid [ACD24] 9.99
8mm/Hi-8 cleaning cassette

Minidisc lens cleaner

CD restorer polish
Sony original dry cleaner [8mmSC] 14.99 This does exactly what it says on the label its a polish that restores your CDs. You get a bottle of fluid and a super-soft cloth. Each pack will treat up to 200 CDs and it cleans and polishes away light scratches and marks to help prevent music CDs skipping or CDROMs mis-reading in your PC. [BIB635N] 4.99
MINI DV HEAD CLEANING CASSETTE

Audio cleaning cassette

Removes deposits from the tape head. C/w fluid
Provides gentle dry cleaning of the laser assembly in Minidisc players/recorders. Background images and music display on the MD whilst cleaning is in progress. Complete with storage box [MDC] 8.99
Safely removes deposits from heads and tape guides, this dry head cleaning cassette can be reused approx 50 times [49679] 7.99

[ARC21]

Wet or dry? Use a dry clean first this usually shifts the deposits. If it doesnt, use a wet clean, but allow at least 5 minutes drying time with the tape door open before trying a tape.

See page 59

AV Distribution Amplifier

Front Rear

Gives four identical AV outputs from one input RCA phono and S connections for video, RCA phono for audio Very wide bandwidth very low distortion design, using state of the art professional ICs DC coupled and fully buffered on both audio and video (Chroma AC coupled) Works with both composite and S video Line drive feature gives improved results when driving long cable lengths (drive video up to 100m) Mains adaptor included Made in England
Keene Electronics, Unit 9, Old Hall Mills Business Park, Little Eaton, Derbys DE21 5DN UK Tel 9000 Fax www.keene.co.uk
Cleaning brushes Record brush
Carbon fibre anti-static cleaning brush for records [ACB25] 3.99