SCT-100-SENSORMATIC-PANASONIC Sensormatic RS-422 to Panasonic RS-485 Code Translator
The code translator converts Sensormatic RS-422 camera control code into Panasonic RS-485 code for a single P/T/Z. Only camera commands for the address matching the Address Selector switches will be converted. Output code is selectable from 2400 baud to 19.2K baud. The output is Panasonic conventional protocol without a unit address so the camera's address switch does not have to be set. A test mode sends a continuous square movement pattern to the P/T/Z so the wiring and baud settings between the translator and the P/T/Z can be checked without a Sensormatic controller.
Configuration Switches Switch 1: Unassigned Up: Down: Switch 2: Unassigned Up: Down: Switch 3: Unassigned Address Selector
Selects camera address. Valid range is 1 ~ 256

Rx Indicator

Flashes when there is any input data. Will stay on if input lines are reversed.

Error Indicator

Flashes when input code is not recognized as valid Sensormatic RS-422 code.

Status Indicator

Flashes to indicate code errors. Will stay on if address switch is out of limits.

Tx Indicator

Flashes when Panasonic code is sent.
Up: Down: Switches 4 &5: Panasonic Baud 4 Down 5 Down Up 5 Down Down 5 Up Up 5 Up 19.2K
Switch 6: Output test code Up: Output test pattern On Down: Output test pattern Off
The removable mounting clip can be snapped onto a din rail or screwed to a panel or wall.

Rsp Out

Data In
WARNING: Connect power to the Pwr inputs. Do not connect power wires to the Gnd.
Removable edge connector. Insert a small screwdriver in the upper slot to force open the wire clamp. Push all the way in to open fully. Place stripped wire end(s) in the open clamp and withdraw screwdriver.

T T (A) (B)

Panasonic RS-485 Out Connect to camera R(A) & R(B). (Set camera for 4 wire mode)

R(A) R(B) T(A) T(B) Gnd

Green Yellow Orange Red Brown Panasonic camera connector viewed from contact side
SPECIFICATIONS Size: Weight: Power: Environmental: 4.5" x 3.5" x 1.25" 0.5 lb 9Volt to 15Volt AC or DC at 75ma Indoor use only
Sennetech, Inc. 6455 W. Bath Rd, Perry, MI 48872 U.S.A. www.sennetech.net
Ph (517) 675-1150 Fax (517) 675-1151
NOTES Switch Settings Any changes in switch settings are effective immediately, they are not read only on power up. Addressing Only camera control code for the camera number set by the Address Switches is converted. The data is sent in a direct mode to the Panasonic camera, its address switches do not matter. Indicators The Rx LED will flash when there is data on the input. If it is on constantly, the input wires may be reversed. The Error LED will flash if the input code is not recognized as valid Sensormatic code. The Status LED will light if the address switches are not set to a valid address (1~256). The Tx LED flashes once for each Panasonic packet sent.
OPERATION PTZ The code translator converts pan, tilt, zoom, focus and iris code directly into Panasonic code Additional commands are converted according to the following table (From a TouchTracker controller). SENSORMATIC COMMAND Presets PANASONIC COMMAND
Define Quck View 1~4 Program preset 1~4 Quck View 1~4 Go to preset 1~4 Note: Presets are not available when used with an AD 2083-02 code translator. Run pattern 1 Define Pattern 2 End of Pattern Run Pattern 2 Iris Open + Iris Close Flip Autopan Patrol Learn Patrol Stop Patrol Play Auto Iris Auto Focus

Autopan Patterns

Auto Iris Auto Focus
Dome Setup Menu In a Sensormatic system, it requires multiple keystrokes to activate the configuration menu. Press and hold Iris Open, press and hold Focus Near or Focus Far, then press Zoom Out. While the menu is displayed, use the tilt to navigate and pan to change selection value Focus Far Focus Near Advance to next high-lighted menu Return to previous menu
(Any iris or zoom command will automatically exit the menu.)