Surround Sound

TV Audio
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 4 Thursday, February 28, 2008

Assembling the speakers

Preparation To prevent damage or scratches, lay down a soft cloth and perform assembly on it. For assembly, use a Phillips-head screwdriver. For optional wall mount, refer to page 7.
[PT760] [PT954] : Front speakers [PT960] [PT954] : Surround speakers
Make sure you have all the indicated components before starting assembly, setup, and connection. [PT760] [PT954] 2 Front speakers [PT760] [PT954] 2 Set of pipes (with cable): For front speakers [PT960] [PT954] 2 Set of pipes (with cable): For surround speakers [PT760] [PT960] 2 Bases [PT954] 4 Bases [PT760] [PT960] 8 Screws [PT954] 16 Screws [PT760] [PT960] 4 Small screws [PT954] 8 Small screws
[PT960] [PT954] 2 Surround speakers

1 Join the pipes.

2 Tighten securely.

Small screws

Match these holes when you insert the pipe. Slide into the groove.
Thread the cable through the base.

Tighten securely. Screws

Phillips-head screwdriver (not included)
Pull and press the cable into the groove.

Tighten securely. Cable

Insert the wire fully. i: White j: Blue Push!
Attach the pipes to the speaker.

5 Press into

Pipe Speaker Screws the groove.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 5 Thursday, February 28, 2008

[PT960] : Front speakers

Make sure you have all the indicated components before starting assembly, setup, and connection. 2 Front speakers 2 Stands (with cable) 2 Bases 8 Screws

Slide into the groove.

Tighten securely.
Insert the wire fully. i: White j: Blue Position the cable between the ridges. Push! Press into the groove. Tighten securely. Leave about 90 mm (317/32z)

Speaker assembly option

Thread the speaker cable through the base. Leave about 100 mm (315/16z) Attach the speaker. Insert the wire fully. i: White j: Blue Push! Press into the groove. Tighten securely.
You can remove and use the cable from the stand. To reattach the cable, refer to page 7.
Preventing the speakers from falling
You will need to obtain the appropriate screw eyes to match the walls or pillars to which they are going to be fastened. Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper attachment may result in damage to the wall or speakers. e.g. [PT760] [PT954] Front speakers String (not included) Thread from the wall to the speaker and tie tightly. e.g. [PT960] Front speakers String (not included) Thread from the wall to the speaker and tie tightly.

Rear of the speaker

Screw eye (not included)

Approx. 150 mm (529/32z)

SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 6 Thursday, February 28, 2008

Positioning

[Note] Keep your speakers at least 10 mm (13/32q) away from the system for proper ventilation. Setup example Place the front, center, and surround speakers at approximately the same distance from the seating position. The angles in the diagram are approximate.
How you set up your speakers can affect the bass and the sound field. Note the following points: Place speakers on flat secure bases. Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with thick curtains.
Subwoofer Place to the right or left of the TV, on the floor or a sturdy shelf so that it will not cause vibration. Leave about 30 cm (1113/16q) from the TV.
e.g. [PT760] [PT954] Front speakers
Center speaker Put on a rack or shelf. Vibration caused by the speaker can disrupt the picture if it is placed directly on the TV.

Main unit

Digital transmitter
To allow for proper ventilation and to maintain good airflow around the main unit, position it with at least 5 cm (2q) of space on all sides.
e.g. [PT760] Surround speakers
Wireless system Place the wireless system within approximately 10 m (33 ft) from the main unit.
Do not use the wireless system or the digital transmitter in a metal cabinet or bookshelf.
To avoid interference, maintain the following distances between the wireless system and other electronic devices that use the same radio frequency (2.4 GHz band). Wireless system Wireless LAN: approx. 2 m (61/2 ft) Cordless phone and other electronic devices: approx. 2 m (61/2 ft)
The wireless system will automatically seek a clear channel if any of these other devices interfere with its communication. When this happens, the wireless link indicator ( [W1] ) flashes on the main unit, and there is a brief interruption in audio coming from the surround speakers. This is the normal operation of the product working to assure the best possible performance of your home theater system. If the interference persists, try moving the other devices to another location outside the range of the wireless system or move the wireless system nearer to the main unit.
Expand your listening options with a multi-room wireless sound system. Optional Panasonic wireless accessory SH-FX85
Notes on speaker use Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be negatively affected. You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods. Reduce the volume in the following cases to avoid damage: When playing distorted sound. When the speakers are reverberating due to a record player, noise from FM broadcasts, or continuous signals from an oscillator, test disc, or electronic instrument. When adjusting the sound quality. When turning the unit on or off.

VIERA Link HDAVI Control

If your Panasonic TV is an HDMI control compatible, you can operate your TV synchronizing with home theater operations or vice versa ( 26, Using the VIERA LinkTM HDAVI ControlTM). Make the audio connection ( above) when you use VIERA Link HDAVI Control function.

COMPONENT VIDEO IN

[COMPONENT\VIDEO] This connection provides a much purer picture than the

VIDEO OUT terminal.

Y PB PR
After making this connection, select DARKER from the BLACK LEVEL in the VIDEO menu ( 23). To enjoy progressive video Connect to a progressive output compatible TV. Set VIDEO OUT (I/P) in VIDEO menu to PROGRESSIVE and then follow the instructions on the menu screen ( 23, VIDEO menu).
All Panasonic televisions that have 480p input connectors are compatible. Consult the manufacturer if you have another brand of TV.
Connect to terminals of the same color.
[Note] Do not make the video connections through the video cassette recorder. Due to copy guard protection, the picture may not be displayed properly. Only one video connection is required. Choose one of the video connections above depending on your TV.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 9 Thursday, February 28, 2008

Other audio connection

Optical digital audio cable Do not bend sharply when connecting.

OPTICAL OUT

Main unit terminal [\\\\\\OPTICAL\IN\\\\\\]
This unit can decode the surround signals received through cable TV box, digital broadcasting or satellite broadcasts. Refer to your equipments operating instructions for details. Only Dolby Digital and PCM can be played with this connection. After making this connection, make settings to suit the type of audio from your digital equipment ( 30).

Speaker connections

Be careful not to cross (short circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers.
Connecting the speakers to the main unit: Connect to terminals of the same color. Speaker 1 FRONT (L) Terminal/connector color White Red Green Purple
FRONT (R) CENTER SUBWOOFER
Main unit Speaker cable sticker (included) Attach the speaker-cable stickers to make connection easier.

e.g. Center speaker

R L CENTER FRONT
Insert fully. Insert the wire fully. i: White j: Blue Wireless system Push!
e.g. [PT760] Surround speaker (R)

i: White

j: Blue
Insert the wires correctly.
Insert the wires, taking care
not to insert beyond the wire insulation.

(Continued on next page)

SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 10 Thursday, February 28, 2008

AM ANT

LOOP ANT GND

EXT LOOP

FM ANT (75 )
Radio antenna connections

[AM\loop\antenna]

(included) Stand the antenna up on its base. Place the antenna where reception is best. Black Red Adhesive tape White Click!

FM ANT (75 ) AM ANT

Keep loose antenna cables away from other wires and cables.

[FM\indoor\antenna]

(included) Affix this end of the antenna where reception is best.
Using an FM/AM outdoor antenna (optional)
Use outdoor antenna if FM/AM radio reception is poor. Disconnect the antenna when the unit is not in use. Do not use the outdoor antenna during an electrical storm. FM outdoor antenna [Using a TV antenna (not included)] The antenna should be installed by a competent technician. AM outdoor antenna [Using a vinyl wire (not included)] Run a piece of vinyl wire horizontally across a window or other convenient location.
5.0 m to 12 m (16 ft to 39 ft) 75 coaxial cable (not included) Leave the AM loop antenna connected.
\U.S.A.\and\Canada] Antenna plug (not included)
Rework your outdoor antennas 75 coaxial cable as follows. 1 Remove a piece of the outer vinyl insulator. 2 Carefully pull the tabs apart to remove the cover. 3 Install the coaxial cable. Clamp the cable conductor, and wind it on so that it does not contact anything else. 4 Attach the cover.

10 mm (13/32z)

Clamp with pliers

Peel back

7 mm (9/32z)
SC-PT760-960P-PC_Body2_Eng (PX).fm Page 11 Friday, February 29, 2008

8:49 AM

Digital transmitter connection

VOLT ADJ

7 Skip or slow-search play / Select the radio stations ( 13, 16) 8 Stop playing / Select the tuning mode / Adjust the FM reception condition ( 13, 16)

Utilizing the START menu

You can select desired source or access playback/menus by using the START menu. When a disc is loaded, you can also access playback or menus from the START menu. e.g. [DVD-V]
DVD/CD Playback Disc TOP MENU (DVD) MENU (DVD) Input select Home theater

Show the START menu.

DVD/CD Home theater

Playback/menu access

Input select
When the on-screen control panel appears

Select an item.

To exit press [START].
e.g. [DVD-V] (when Playback Disc is selected from the START menu)
When Input select is selected
You can select a desired source from the menu. DVD/CD ( 12), FM ( 13), AM ( 13), AUX ( 30), DIGITAL IN ( 30), iPod ( 30) (TV) will appear beside AUX or DIGITAL IN, indicating the TV audio setting for VIERA Link HDAVI Control ( 26). Press [3, 4], then press [OK] to make the settings.

SEARCH PLAY STOP

SEARCH RETURN
You can operate the playback with the indicated controls.
Control reference guide / Utilizing the START menu
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 16 Thursday, February 28, 2008

Basic play

Preparation To display the picture, turn on your TV and change its video input mode.

Using the main unit

Turn on the unit.

Select DVD/CD.

Label facing up

Open all the disc trays.

To select a desired tray ( below, Selecting the desired tray). Press [<OPEN/CLOSE] again to close all the disc trays.

Start play.

Turn [`, i VOLUME] to adjust the volume. You can enjoy surround sound when you press [PLII] on the remote control to turn on Dolby Pro Logic II ( 28).

Load the disc.

Load double-sided discs so the label for the side you want to play is facing up. Press [EXCHANGE] to load discs one by one. For DVD-RAM, remove the disc from its cartridge before use. Do not: Load more than one disc per tray. Push or pull out the tray by hand.

On-screen item select

Confirm
[DVD-VR] [DVD-V] [VCD] [CD] e.g. To select 12: [S10] [1] [2]
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 18 Thursday, February 28, 2008

Other playback functions

CD MODE STOP
Program play (up to 30 items) 1-Disc program
[DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG] You can program all the items on a disc in the selected tray.
OK RETURN PLAY MODE REPEAT

e.g. [DVD-V]

DVD-V PROGRAM SELECT TITLE TITLE 1 TITLE 2 TITLE 3 TITLE 4 TITLE CHAP. CLEAR ALL
RETURN PLAY LIST -PLAY MODE SOUND PL -REPEAT FL DISPLAY W.S. SUBWOOFER LEVEL MUTING
Playing CDs sequentially (CD Mode)
[VCD] [CD] [WMA] [MP3] This feature allows you to play all loaded CDs sequentially. Select an applicable disc before playing ( 17, Selecting a disc). While stopped

S TA R T: P L AY

Repeat this step to program other items. To return to the previous menu, press [RETURN].

P.MODE

CD W1 W2
All-Disc program (when CD Mode is on)
[VCD] [CD] You can program all the items on all the discs. 1 Press [3, 4], and then press [OK] to select the disc. 2 Press [3, 4], and then press [OK] to select the track. 3 Repeat step 1 and 2 to program other items. To return to the previous menu, press [RETURN]. 4 Press [1 PLAY]. To select all the items Press [3, 4] to select ALL and press [OK]. To clear the selected program 1 Press [1] and then press [3, 4] to select the program. 2 Press [CANCEL]. To clear the whole program Press [1] several times to select CLEAR ALL, and then press [OK]. The whole program is also cleared when the disc tray is opened, the unit is turned off or another source is selected.
If all loaded discs are DVDs, CD Mode does not work. Video CD playback control are disabled. You cannot turn CD Mode on or off during program or random mode. If you want to play a DVD, press and hold [CD MODE] again while stopped to cancel CD Mode. (CD Mode is also canceled when you switch the unit to standby, select another source, or when the disc tray is opened.)

Repeat play

This works only when the elapsed play time can be displayed. It also works with all JPEG content.

To start from a specific item [VCD] This does not work when using playback control. e.g. [DVD-V] : T2 C5 To select numbers for data disc e.g. 123: [S10] [1] [2] [3] [OK] [DVD-VR] [DVD-V] To change play speed from k0.6 to k1.4 (in 0.1-unit steps) Press [1 PLAY] to return to normal play. After you change the speed Dolby Pro Logic II has no effect. Audio output switches to 2-channel stereo. Sampling frequency of 96 kHz is converted to 48 kHz. This function may not work depending on the discs recording. ( 18, Repeat play) A-B Repeat (To repeat a specified section) Except [JPEG] [DVD-VR] (Still picture part) [VCD] (SVCD) Press [OK] at the starting and ending points. Select OFF to cancel. [DVD-V] (with multiple subtitles) [VCD] (SVCD only) To select subtitle language On iR/iRW, a subtitle number may be shown for subtitles that are not displayed.

PLAY SPEED

[DVD-V] (with multiple soundtracks) To select audio soundtrack [DVD-VR] [VCD] To select L, R, L+R or L R [DVD-V] (Karaoke disc) To select ON or OFF for vocals To select OFF, V1, V2 or V1+V2 for vocal selections Actual operations depend on the disc. Read the discs instructions for details. Signal type/data LPCM/PPCM/D/DTS/MP3/MPEG: Signal type kHz (Sampling frequency)/bit/ch (Number of channels) e.g. 3/2.1ch.1: Low frequency effect (not displayed if there is no signal).0: No surround.1: Mono surround.2: Stereo surround (left/right).1: Center.2: Front leftiFront right.3: Front leftiFront rightiCenter

REPEAT MODE

SUBTITLE
[DVD-VR] (with subtitle on/off information) To select ON or OFF This may not work depending on the disc. [DVD-V] (with multiple angles) To select a video angle
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 21 Thursday, February 28, 2008
[JPEG] To select ON or OFF for pictures date display

Menu 4 (HDMI)

DATE DISPLAY
To rotate a picture (during pause) [JPEG] : 0,------. 90,------.180,------.270 ^--------------------------------------------J
To show HDMI information. ( below, Confirming HDMI information) This works when the HDMI connection is being used with VIDEO PRIORITY ( 24, HDMI menu) set to ON.

HDMI STATUS

ROTATION

Menu 2 (Video)

NORMAL CINEMA1: Mellows images and enhances detail in dark scenes. CINEMA2: Sharpens images and enhances detail in dark scenes. DYNAMIC: Enhances the contrast for powerful images. ANIMATION: Suitable for animation. To select zoom sizes NORMAL, AUTO ([DVD-VR] [DVD-V] [VCD]), k2, k4

HD ENHANCER

To sharpen the 720p, 1080i and 1080p picture quality OFF, 1 (weakest) to 3 (strongest) This works when the HDMI connection is being used with VIDEO PRIORITY ( 24, HDMI menu) set to ON. To select suitable picture quality with your TV (Video recordings will be converted to, and output as, high-definition video.)

DISPLAY menu

LANGUAGE

HDMI menu

VIDEO PRIORITY
ON: When using the HDMI AV OUT terminal for video output. The resolution of the video output from the HDMI AV OUT terminal is optimized according to the capability of the connected equipment (e.g. TV). OFF: When not using the HDMI AV OUT terminal for video output. Video output will not depend on the connected equipment, but on this unit. ON: When audio output is from the HDMI AV OUT terminal. (Depending on the capabilities of the connected equipment, audio output may differ from the audio settings of the main unit.) OFF: When audio output is not from the HDMI AV OUT terminal. (The audio is output using the settings of the main unit.)
STANDARD This works only when COLOR SPACE ENHANCED: When the black and white images are not distinct. in Menu 4 (HDMI) is set to RGB ( 21).

RGB RANGE

VIERA Link
ON: The VIERA Link HDAVI Control function is available ( 26). OFF

OTHERS menu

JPEG TIME
Set the speed of the slideshow. Factory preset: 3 SEC 1 SEC to 15 SEC (in 1-unit steps) 15 SEC to 60 SEC (in 5-unit steps) 60 SEC to 180 SEC (in 30-unit steps) BRIGHT DIM AUTO: The display is dimmed, but brightens when you perform some operations. SET Follow the on-screen instructions. DVD-VR: To play the video programs on DVD-RAM or DVD-R/-RW. DATA: To play the data files on DVD-RAM or DVD-R/-RW. RESET The password screen is shown if RATINGS ( 22) is set. Please enter the same password, then turn the unit off and on again.

FL DIMMER

Change the brightness of the units display.

QUICK SETUP DVD-VR/DATA

Select to play only DVD-VR or DATA format.

DEFAULTS

This returns all values in the MAIN menu to the default settings.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 25 Thursday, February 28, 2008
Selecting the delay time of the speakers
(Effective when playing 5.1-channel sound) (Center and surround speakers only) For optimum listening with 5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position. If you have to place the center or surround speakers closer to the seating position, adjust the delay time to make up for the difference.

To start disc playback.

This units speakers will be automatically activated ( 27).
This function also works if you press [1 PLAY] on this units remote control when this unit is in standby mode. [Note] Playback may not be immediately displayed on the TV. If you miss the beginning portion of playback, press [:] or [6] to go back to where playback started.

Auto input switching

When you switch the TV input to TV tuner mode, this unit will automatically switch to AUX or D-IN. (This does not work when this unit is in IPOD mode.) When you start disc play, the TV will automatically switch its input mode for this unit.

Power off link

When the TV is turned off, this unit goes into standby mode automatically. This function works only when DVD/CD, AUX or D-IN is selected as the source on this unit. When the TV is turned on, this unit does not turn on automatically. (Power on link is not available.) [Note] When you press [], only this unit turns off. Other connected equipment compatible with VIERA Link HDAVI Control stays on.
AUX or D-IN (DIGITAL IN) works depending on the TV AUDIO
setting ( above, Setting the TV audio for VIERA Link HDAVI Control).
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 27 Thursday, February 28, 2008

Speaker control

You can select whether audio is output from this units speakers or the TV speakers by using the TV menu settings. For details, refer to the operating instructions of your TV. Home theater This units speakers are active. When this unit is in standby mode, changing the TV speakers to this units speakers in the TV menu will automatically turn this unit on and select AUX or D-IN as the source. The TV speakers are automatically muted. You can control the volume setting using the volume or mute button on the TVs remote control. (The volume level is displayed on the main units FL display.) To cancel muting, you can also use this units remote control ( 14). If you turn off this unit, TV speakers will be automatically activated. TV TV speakers are active. The volume of this unit is set to 0. This function works only when DVD/CD, AUX or D-IN is selected as the source on this unit. Audio output is 2-channel audio. When switching between this unit speakers and TV speakers, the TV screen may be blank for several seconds. 2
VIERA Link Control only with TVs remote control [for HDAVI Control 2 (or later)]
You can control the playback menus of this unit with the TVs remote control. When operating the TVs remote control, refer to the below illustration for operation buttons. 1 Select this units operation menu by using the TV menu settings. (For details, refer to the operating instructions of your TV.) The START menu will be shown. e.g. [DVD-V]

NODISC F61 F76 DVD U11 ERROR DVD H DVD F stands for a number. [W1] is flashing.

11, 14

U70 stands for a number. The actual number following U70 will depend on the state of the main unit. REMOTE 1 or REMOTE 2

LOADING

General operation
No response when any buttons are pressed. This unit cannot play discs other than the ones listed in these operating instructions. The unit may not be operating properly due to lightning, static electricity or some other external factor. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC supply cord, and then reconnect it. Condensation has formed. Wait 1 to 2 hours for it to evaporate. Check that the batteries are installed correctly. The batteries are depleted. Replace them with new ones. Aim the remote control at the remote control signal sensor and operate. Change the remote control operating mode. CD Mode is on. Press and hold [CD MODE] to turn CD Mode off. Check the video or speaker connection. Check the power or input setting of the connected equipment and the main unit. Check that the disc has something recorded on it. While stopped and DVD/CD is the source, press and hold [] (Stop) on the main unit and [S10] on the remote control until INITIALIZED disappears from the TV. Turn the unit off and on again. All settings will return to the default values. (This does not work during program and random modes, or when setup menu or START menu is displayed.) Depending on the condition of this unit or the connected equipment, it may be necessary to repeat the same operation so that the function can work correctly. The settings for TV ASPECT1 and LANGUAGE2 will automatically follow to the settings of the TV. Select using TV settings.

18 8, 9

No response when remote control buttons are pressed. Other products respond to the remote control. Cannot play DVDs. No picture or sound.
You have forgotten your ratings password. Reset all the settings to Factory Preset. The VIERA Link HDAVI Control function does not respond.
The setting you made in TV ASPECT ( 23, VIDEO menu) or LANGUAGE ( 24, DISPLAY menu) does not work.
When using VIERA Link HDAVI Control with HDAVI Control 3 compatible TV When using VIERA Link HDAVI Control with HDAVI Control 2 (or later) compatible TV
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 35 Thursday, February 28, 2008

SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 43 Thursday, February 28, 2008
Limited Warranty (ONLY FOR CANADA)

Panasonic Canada Inc.

PANASONIC PRODUCT LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase. Technics Audio Product Panasonic Portable / Clock Radio (without Tape, CD, MD) Panasonic Audio / SD Audio Product Panasonic DVD Product Panasonic Combination DVD Player / VCR Panasonic Combination DVD Recorder / VCR Accessories including rechargeable batteries One (1) year, parts and labour One (1) year, parts and labour One (1) year, parts and labour One (1) year, parts and labour One (1) year, parts and labour One (1) year, parts and labour Ninety (90) days
LIMITATIONS AND EXCLUSIONS This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed, subjected to usage for which the product was not designed, misused or abused, damaged during shipping, or which has been altered or repaired in any way that affects the reliability or detracts from the performance, nor does it cover any product which is used commercially. Dry cell batteries are also excluded from coverage under this warranty. This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. WARRANTY SERVICE FOR PRODUCT OPERATION ASSISTANCE, please contact:
Our Customer Care Centre:
Telephone #: 1-800 #: Fax #: Email link:

(Inside of product) The laser product label has not been attached to products for the U.S.A. and Canada.
THE FOLLOWING APPLIES ONLY IN CANADA.
This device complies with RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation of the device. For wireless system Product Identification Marking is located on the bottom of unit. [For[U.S.A.] [For[Canada] [For[Others[

(Side of product)

Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America
One Panasonic Way Secaucus, New Jersey 07094 http://www.panasonic.com
5770 Ambler Drive Mississauga, Ontario L4W 2T3 www.panasonic.ca
Matsushita Electric Industrial Co., Ltd. Corporate Management Division for the Americas
Sales Office for North America Tokyo Panasonic Sales Section 32nd Floor, World Trade Center 4-1, Hamamatsu-cho, 2-Chome, Minato-Ku, Tokyo 105-6132, Japan
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantera, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Marketing Europe G.M.B.H.
Wiesbaden N. (a Division of Panasonic Marketing G.M.B.H.) Military Sales Department 6200 Wiesbaden-Biebrich, Hagenauerstr. 43 Germany
C 2007 Matsushita Electric Industrial Co., Ltd. Printed in Singapore

F1207AD4038