THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND CANADA (For wireless system) The following mark and symbols are located on bottom of the unit.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 10) Protect the power cord from being walked on or pinched particularly 2) Keep these instructions. at plugs, convenience receptacles, and the point where they exit from 3) Heed all warnings. the apparatus. 4) Follow all instructions. 11) Only use attachments/accessories specified by the manufacturer. 5) Do not use this apparatus near water. 12) Use only with the cart, stand, tripod, bracket, or table 6) Clean only with dry cloth. specified by the manufacturer, or sold with the 7) Do not block any ventilation openings. Install in accordance with the apparatus. When a cart is used, use caution when manufacturers instructions. moving the cart/apparatus combination to avoid injury 8) Do not install near any heat sources such as radiators, heat registers, from tip-over. stoves, or other apparatus (including amplifiers) that produce heat. 13) Unplug this apparatus during lightning storms or when 9) \U.S.A.\and\Canada] unused for long periods of time. Do not defeat the safety purpose of the polarized or grounding-type 14) Refer all servicing to qualified service personnel. Servicing is required plug. A polarized plug has two blades with one wider than the other. when the apparatus has been damaged in any way, such as A grounding-type plug has two blades and a third grounding prong. power-supply cord or plug is damaged, liquid has been spilled or The wide blade or the third prong are provided for your safety. If the objects have fallen into the apparatus, the apparatus has been provided plug does not fit into your outlet, consult an electrician for exposed to rain or moisture, does not operate normally, or has been replacement of the obsolete outlet. dropped.

COMPONENT VIDEO IN

[COMPONENT\VIDEO] This connection provides a much purer picture than the

VIDEO OUT terminal.

Y PB PR
After making this connection, select DARKER from the BLACK LEVEL in the VIDEO menu ( 23). To enjoy progressive video Connect to a progressive output compatible TV. Set VIDEO OUT (I/P) in VIDEO menu to PROGRESSIVE and then follow the instructions on the menu screen ( 23, VIDEO menu).
All Panasonic televisions that have 480p input connectors are compatible. Consult the manufacturer if you have another brand of TV.
Connect to terminals of the same color.
[Note] Do not make the video connections through the video cassette recorder. Due to copy guard protection, the picture may not be displayed properly. Only one video connection is required. Choose one of the video connections above depending on your TV.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 9 Thursday, February 28, 2008

Other audio connection

Optical digital audio cable Do not bend sharply when connecting.

OPTICAL OUT

Main unit terminal [\\\\\\OPTICAL\IN\\\\\\]
This unit can decode the surround signals received through cable TV box, digital broadcasting or satellite broadcasts. Refer to your equipments operating instructions for details. Only Dolby Digital and PCM can be played with this connection. After making this connection, make settings to suit the type of audio from your digital equipment ( 30).

Speaker connections

Be careful not to cross (short circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers.
Connecting the speakers to the main unit: Connect to terminals of the same color. Speaker 1 FRONT (L) Terminal/connector color White Red Green Purple
FRONT (R) CENTER SUBWOOFER
Main unit Speaker cable sticker (included) Attach the speaker-cable stickers to make connection easier.

e.g. Center speaker

R L CENTER FRONT
Insert fully. Insert the wire fully. i: White j: Blue Wireless system Push!
e.g. [PT760] Surround speaker (R)

i: White

j: Blue
Insert the wires correctly.
Insert the wires, taking care
not to insert beyond the wire insulation.

(Continued on next page)

SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 10 Thursday, February 28, 2008

AM ANT

Preparing the remote control
Do not use rechargeable type batteries. Do not heat or expose to flame. Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed.

Batteries

Insert so the poles (i and j) match those in the remote control.

Do not:

Press in and lift up. mix old and new batteries. use different types at the same time. take apart or short circuit. attempt to recharge alkaline or manganese batteries. use batteries if the covering has been peeled off. Mishandling of batteries can cause electrolyte leakage which can severely damage the remote control. Remove the batteries if the remote control is not going to be used for a long period of time. Store in a cool, dark place.

R6/LR6, AA

Replace the cover.
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions.
Aim at the remote control signal sensor ( 15), avoiding obstacles, at a maximum range of 7.0 m (23 ft) directly in front of the unit.
Digital transmitter connection / AC cord connections / Preparing the remote control
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 12 Thursday, February 28, 2008

Performing QUICK SETUP

Preparation Turn on your TV and select the appropriate video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.). To change your TVs video input mode, refer to its operating instructions. This remote control can perform some basic TV operations ( 14).
The QUICK SETUP screen assists you to make necessary settings.
Turn on the unit. Select DVD/CD. Show the setup menu.
MAIN DISC VIDEO AUDIO DISPLAY HDMI OTHERS

TV / VIDEO

-2ND SELECT

SELECT

SET RETURN

EXIT : SETUP

OK RETURN

Select OTHERS.

-CD MODE

SLOW / SEARCH

ONE TOUCH PLAY

Select QUICK SETUP.

ON NCTI S FU

TOP MEN

Select SET.
RETURN PLAY LIST -PLAY MODE SOUND PL -REPEAT FL DISPLAY
W.S. SUBWOOFER LEVEL MUTING

CANCEL

Select Yes.
OTHERSQUICK SETUP SELECT THE MENU LANGUAGE.

-SLEEP -CH SELECT

ENGLISH FRANAIS ESPAOL
Follow the messages and make the settings.
MENU LANGUAGE TV TYPE TV ASPECT
To return to the previous screen, press [RETURN].

Details of settings

MENU LANGUAGE
Choose the language for the on-screen messages. ENGLISH FRANAIS ESPAOL
Finish QUICK SETUP. Exit.

5 DISC SELECTOR

EXCHANGE

OPEN CLOSE

SW BOOST

TUNE MODE

FM MODE

VOLUME

CLO SE

SW BOOS T

1 Standby/on switch [POWER /I] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. ( 16) DISC SELECTOR Select a disc directly ( 16) 3 Disc exchange Open the disc tray to exchange the disc. ( 16) 4 Open/Close the disc tray ( 16) 5 Turn Subwoofer Boost on/off ( 29) 6 Select the source
DVD/CD#FM#AM#AUX#D-IN#IPOD ^--------------------------------------------------------------}
9 Play discs / Memorize the receiving radio stations ( 16, 29) : Connect iPod ( 30) ; Remote control signal sensor < Display = Adjust the volume of the main unit > [PT960] Jog LED
Lights when the unit is turned on.
? Connect headphones (not included)
Headphone plug type: 3.5 mm (1/8z) stereo mini plug Reduce the volume before connecting. Audio is automatically switched to 2-channel stereo. To prevent hearing damage, avoid listening for prolonged periods of time. Excessive sound pressure from earphones and headphones can cause hearing loss.
7 Skip or slow-search play / Select the radio stations ( 13, 16) 8 Stop playing / Select the tuning mode / Adjust the FM reception condition ( 13, 16)

Utilizing the START menu

You can select desired source or access playback/menus by using the START menu. When a disc is loaded, you can also access playback or menus from the START menu. e.g. [DVD-V]
DVD/CD Playback Disc TOP MENU (DVD) MENU (DVD) Input select Home theater

Show the START menu.

DVD/CD Home theater

Playback/menu access

Input select
When the on-screen control panel appears

Select an item.

To exit press [START].
e.g. [DVD-V] (when Playback Disc is selected from the START menu)
When Input select is selected
You can select a desired source from the menu. DVD/CD ( 12), FM ( 13), AM ( 13), AUX ( 30), DIGITAL IN ( 30), iPod ( 30) (TV) will appear beside AUX or DIGITAL IN, indicating the TV audio setting for VIERA Link HDAVI Control ( 26). Press [3, 4], then press [OK] to make the settings.

SEARCH PLAY STOP

SEARCH RETURN
You can operate the playback with the indicated controls.
Control reference guide / Utilizing the START menu
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 16 Thursday, February 28, 2008

Basic play

Preparation To display the picture, turn on your TV and change its video input mode.

Using the main unit

Turn on the unit.

Select DVD/CD.

Label facing up

Open all the disc trays.

To select a desired tray ( below, Selecting the desired tray). Press [<OPEN/CLOSE] again to close all the disc trays.

Start play.

Turn [`, i VOLUME] to adjust the volume. You can enjoy surround sound when you press [PLII] on the remote control to turn on Dolby Pro Logic II ( 28).

Load the disc.

Load double-sided discs so the label for the side you want to play is facing up. Press [EXCHANGE] to load discs one by one. For DVD-RAM, remove the disc from its cartridge before use. Do not: Load more than one disc per tray. Push or pull out the tray by hand.

(Stop)

, + VOLUME
Press to select a disc directly.
You can also select the disc using the remote control ( 17, Selecting a disc).
Press to skip. Press and hold to
search during play start slow-motion play during pause Press [1] (Play) to start normal play.

During play,

Selecting the desired tray
Change discs without interrupting playback
Press [<OPEN/CLOSE] again to close the tray.
All trays are opened (except the tray that the disc is playing). Press [EXCHANGE] to close the top tray. Press again until all the trays are closed.
[Note] DISC CONTINUES TO ROTATE WHILE MENUS ARE DISPLAYED. To preserve the units motor and your TV screen, press [] (Stop) when you are finished with the menus. Total title number may not be displayed properly on iR/iRW.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 17 Thursday, February 28, 2008
If you are experiencing problems, refer to troubleshooting ( 34 to 36). Using the remote control
Disc information screen is displayed.
To exit the screen, press [DISC]. e.g. [DVD-V]

DISC CHANGE

Select

SLOW/SEARCH

ONE TOUCH PLAY OK RETURN FL DISPLAY

Selecting a disc

DVD-VIDEO CD DATA-DISC UNCHECKED NO DISC

Confirm or

Empty tray

Not yet read

TOP MENU, DIRECT NAVIGATOR MENU, PLAY LIST
Enter number One touch play
The main unit automatically turns on and starts playing the disc in the tray. The position is memorized while RESUME STOP is on the screen. Press [1 PLAY] to resume. Press [ STOP] again to clear the position. Press [1 PLAY] to restart play.

If all loaded discs are DVDs, CD Mode does not work. Video CD playback control are disabled. You cannot turn CD Mode on or off during program or random mode. If you want to play a DVD, press and hold [CD MODE] again while stopped to cancel CD Mode. (CD Mode is also canceled when you switch the unit to standby, select another source, or when the disc tray is opened.)

Repeat play

This works only when the elapsed play time can be displayed. It also works with all JPEG content.

1 During play -PLAY MODE

-REPEAT

Show the repeat mode.

Random play
(press and hold) repeat 2 While thedisplayed mode is

-PLAY MODE -REPEAT

Select an item to be repeated.
e.g. [DVD-V] `TITLE ---. `CHAP. ---. `OFF ^------------------------------------------------------b To cancel, select OFF.

1-Disc random

[VCD] [CD] You can playback all the items on a disc in the selected tray in random order. [DVD-V] [WMA] [MP3] [JPEG] You can playback selected item(s) on a disc in the selected tray in random order.
(Only when the disc has groups or multiple titles.)

Select a group or title.

Items shown differ depending on the type of disc and playback mode. e.g. [DVD-V] represents selected. To deselect, press [OK] again.
DVD-V RANDOM SELECT TITLE TITLE 1 TITLE 2 TITLE 3

Program and Random play

To enjoy program or random play with: 1 disc : ensure CD Mode ( above) is off all discs: ensure CD Mode is on While stopped

Select the play mode.

Program and random playback screens appear sequentially. Program ------------------------------------------) Random ^--- Exit program and random screens (}
P R E S S P L AY T O S TA R T
[DVD-VR] Select DATA in DVD-VR/DATA ( 24, OTHERS menu) to play WMA, MP3 or JPEG contents. [DVD-V] Some items cannot be played even if you have programmed them.
All-Disc random (when CD Mode is on)
[VCD] [CD] You can playback all the items on all the discs in random order. Press [1 PLAY].
ALL DISC RANDOM PRESS PLAY TO START

e.g. [CD]

SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 19 Thursday, February 28, 2008

Using navigation menus

Selecting the picture in Thumbnail menu

[JPEG]

1 While picture is displayed

NAV I TOP ME NU G ATOR

e.g. Group and content number

G 1/ 1:C 3/ 9

SKIP STOP

Group name

JPEG images
DIRECT NAVIGATOR TOP MENU MENU, PLAY LIST

Select a picture.

Press [:, 9 SKIP] to skip page by page.

Playing data discs

[WMA] [MP3] [JPEG] [DVD-VR] Select DATA in DVD-VR/DATA ( 24, OTHERS menu) to play WMA, MP3 or JPEG contents.
To go to other group 1 Press [3] to select the group name. 2 Press [2, 1] to select the group and press [OK].

If the picture is distorted, press and hold [CANCEL] until the picture is displayed correctly. (The output will return to 480p.)
This works when the HDMI connection is being used with VIDEO PRIORITY ( 24, HDMI menu) set to ON. To select suitable picture color with your TV YCb Cr (4:2:2) Luminance and color details is sent separately. Most of the picture details are in luminance. The color rate is much higher than composite video. Compatible for all TV models. YCb Cr (4:4:4) All color details is sent. Luminance and color details are in same signal. RGB Component video type of signal. If the setting above is not compatible with your TV, it will not be displayed.

TRANSFER MODE

COLOR SPACE

Menu 3 (Audio)

To make the dialogue in movies easier to hear [DVD-V] (Dolby Digital, DTS, 3-channel or higher, with the dialogue recorded in the center channel) OFF, ON OFF, MOVIE, MUSIC ( 28, Using Dolby Pro Logic II)

DIALOGUE ENHANCER

Terms are descriptions of the sample formats used in digital video. YCb Cr is a video signal for luminance (Y), blue (Cb) and red (Cr) details.

Dolby PL II

Confirming HDMI information

HDMI --- INFORMATION

CONNECTED STATE AUDIO STREAM MAX CHANNEL VIDEO FORMAT COLOR SPACE
CONNECTED PCM 2ch 720p YCbCr 4:4:4
1 Connection status 2 Shows the output signal type. 3 Shows the number of audio channels. 4 ( above, VIDEO FORMAT) 5 ( above, COLOR SPACE)
[Note] When OFF is selected in AUDIO OUT ( 24, HDMI menu), will be displayed in AUDIO STREAM.
The numbers displayed depend on the disc being played. One of the above numbers is displayed.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 22 Thursday, February 28, 2008
Changing the player settings

Show the setup menu.

Select the menu.
Display the current setting of the items below
DISC SETTING STATE AUDIO SUBTITLE MENUS RATINGS PASSWORD ENGLISH AUTO ENGLISH 8 NO LIMIT

Setting

To return to the previous screen, press [RETURN].
The settings remain intact even if you switch the unit to standby. Underlined items are the factory settings in the following table.
QUICK SETUP enables successive settings of the items in the shaded area.

DISC menu

Choose the audio language. ENGLISH AUTO3 ENGLISH FRENCH ENGLISH FRENCH SPANISH FRENCH SPANISH ORIGINAL1 SPANISH OTHER 2 OTHER 2
Choose the subtitle language.
Choose the language for disc menus. Changing the menu language in QUICK SETUP also changes this setting.

OTHER 2

RATINGS
Set a rating level to limit DVD-Video play.

To start disc playback.

This units speakers will be automatically activated ( 27).
This function also works if you press [1 PLAY] on this units remote control when this unit is in standby mode. [Note] Playback may not be immediately displayed on the TV. If you miss the beginning portion of playback, press [:] or [6] to go back to where playback started.

Auto input switching

When you switch the TV input to TV tuner mode, this unit will automatically switch to AUX or D-IN. (This does not work when this unit is in IPOD mode.) When you start disc play, the TV will automatically switch its input mode for this unit.

Power off link

When the TV is turned off, this unit goes into standby mode automatically. This function works only when DVD/CD, AUX or D-IN is selected as the source on this unit. When the TV is turned on, this unit does not turn on automatically. (Power on link is not available.) [Note] When you press [], only this unit turns off. Other connected equipment compatible with VIERA Link HDAVI Control stays on.
AUX or D-IN (DIGITAL IN) works depending on the TV AUDIO
setting ( above, Setting the TV audio for VIERA Link HDAVI Control).
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 27 Thursday, February 28, 2008

Speaker control

You can select whether audio is output from this units speakers or the TV speakers by using the TV menu settings. For details, refer to the operating instructions of your TV. Home theater This units speakers are active. When this unit is in standby mode, changing the TV speakers to this units speakers in the TV menu will automatically turn this unit on and select AUX or D-IN as the source. The TV speakers are automatically muted. You can control the volume setting using the volume or mute button on the TVs remote control. (The volume level is displayed on the main units FL display.) To cancel muting, you can also use this units remote control ( 14). If you turn off this unit, TV speakers will be automatically activated. TV TV speakers are active. The volume of this unit is set to 0. This function works only when DVD/CD, AUX or D-IN is selected as the source on this unit. Audio output is 2-channel audio. When switching between this unit speakers and TV speakers, the TV screen may be blank for several seconds. 2
VIERA Link Control only with TVs remote control [for HDAVI Control 2 (or later)]
You can control the playback menus of this unit with the TVs remote control. When operating the TVs remote control, refer to the below illustration for operation buttons. 1 Select this units operation menu by using the TV menu settings. (For details, refer to the operating instructions of your TV.) The START menu will be shown. e.g. [DVD-V]

Using the iPod

You can play an external source through your home theater system. Preparation To view photos/videos from the iPod Ensure the video connection to the VIDEO OUT terminal on this unit ( 8). Operate the iPod menu to make the appropriate photo/video output settings for your TV. (Refer to operating instructions of your iPod.) To display the picture, turn on the TV and select the appropriate video input mode. Before connecting/disconnecting the iPod, turn the main unit off or reduce the volume of the main unit to its minimum.

Enjoying TV audio

Preparation Confirm the audio connection to the AUX terminal on the main unit ( 8).

Select AUX.

Connect the iPod (not included) firmly.
Reduce the volume on the TV to its minimum, and then adjust the volume of the main unit. You can enjoy surround sound effect when you press [PLII] to turn on Dolby Pro Logic II ( 28). Recharging starts when the iPod is inserted. e.g. iPod Dock adapter (not included) Dock for iPod Main unit

Enjoying digital audio

Preparation Confirm the audio connection to the OPTICAL IN terminal on the main unit ( 9).
Select D-IN (Digital In).
Hold the dock when connecting/disconnecting the iPod. Attach the dock adapter which should be supplied with your iPod to the dock for the stable use of the iPod. If you need an adapter, consult your iPod dealer.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 31 Thursday, February 28, 2008

Select IPOD.

The iPod automatically switches to this units display mode. Music menu appears on the TV. e.g.
iPod Playlists Ar tists Albums Songs Podcasts Genres Composers Audiobooks OK Home theater

Enjoying photos/videos

Switch the iPod to its own display mode.
Proceed operations through display of iPod.
a slideshow or video on 2 Playpicture will be displayed on youryour iPod. The TV.
You can also use the remote control to operate iPod menu. [3, 4]: To navigate menu items [OK]: To go to the next menu [RETURN]: To return to the previous menu
To operate through display of iPod, press [FUNCTIONS].

Music discs

Recorded discs (: Playable, : Not playable)
Disc Logo Recorded on a DVD video recorder, etc.

[DVD-VR]2 [DVD-V]4

Recorded on a personal computer, etc.

[WMA] [MP3] [JPEG]

Finalizing6

DVD-RAM

Not necessary

DVD-R/RW

Necessary

DVD-R DL

()5 ()5

iR/iRW iR DL CD-R/RW

Necessary Necessary Necessary7
It may not be possible to play all the above-mentioned discs in some cases due to the type of disc, the condition of the recording, the recording method, or how the files were created ( 33, Tips for making data discs).
This unit can play CD-R/RW recorded with CD-DA or Video CD format. Discs recorded on DVD recorders or DVD video cameras, etc. using Version 1.1 of the Video Recording Format (a unified video recording standard). Discs recorded on DVD recorders or DVD video cameras using Version 1.2 of the Video Recording Format (a unified video recording standard). Discs recorded on DVD recorders or DVD video cameras using DVD-Video Format. Recorded using a format different from DVD-Video Format, therefore some functions cannot be used. A process that allows play on compatible equipment. To play a disc that is indicated as Necessary, the disc must first be finalized on the device it was recorded on. Closing the session will also work.
Note about using a DualDisc
The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so playback may not be possible.
Disc handling precautions
Do not attach labels or stickers to discs. This may cause disc warping, rendering it unusable. Do not write on the label side with a ball-point pen or other writing instrument. Do not use record cleaning sprays, benzine, thinner, liquids which prevent static electricity, or any other solvent. Do not use scratch-proof protectors or covers. Do not use the following discs: Discs with exposed adhesive from removed stickers or labels (rented discs, etc.). Discs that are badly warped or cracked. Irregularly shaped discs, such as heart shapes.
Discs that cannot be played
Blu-ray, HD DVD, AVCHD discs, DVD-RW version 1.0, DVD-Audio, DVD-ROM, CD-ROM, CDV, CD-G, SACD, DivX Video Discs and Photo CD, DVD-RAM that cannot be removed from their cartridge, 2.6 GB and 5.2 GB DVD-RAM, and Chaoji VCD available on the market including CVD, DVCD and SVCD that do not conform to IEC62107.
SC-PT760-960P-PC_RQTX0105-P_eng (PX).book Page 33 Thursday, February 28, 2008
Tips for making data discs

Format

CD-R/RW

Extension

[PT960] [PT954] [Surround\speakers\SB-HS960] Type Speaker unit(s) Full range Input power (IEC) Output sound pressure Frequency range Dimensions (WtHtD) Mass [Weight] [Center\speaker\SB-HC760] Type Speaker unit(s) 1. Full range 2. Full range Input power (IEC) Output sound pressure Cross over frequency Frequency range Dimensions (WtHtD) Mass [Weight] [Subwoofer\SB-HW560] Type Speaker unit(s) 1. Woofer 2. Passive Radiator Input power (IEC) Output sound pressure Frequency range Dimensions (WtHtD) Mass [Weight] 1 way, 1 speaker system (Kelton type) Impedance cm (61/2z) Cone type 25 cm (10z) 250 W (Max) 78 dB/W (1.0 m) 35 Hz to 200 Hz (j16 dB) 40 Hz to 198 Hz (j10 dB) 181 mmk361 mmk315 mm (71/8zk147/32zk1213/32z) 4.7 kg (10.4 lbs) 1 way, 1 speaker system (Bass reflex) Impedance 3 6.5 cm (21/2z) Cone type 125 W6 (Max) 80 dB/W (1.0 m) 86 Hz to 25 kHz (j16 dB) 98 Hz to 22 kHz (j10 dB) 252 mmk1123 mmk235 mm (929/32zk447/32zk91/4z) 2.4 kg (5.2 lbs)
approx. 0.3 W approx. 0.4 W
WIRELESS SYSTEM AND DIGITAL TRANSMITTER
[AMPLIFIER\SECTION] RMS output power Surround Ch 125 W per channel (3 ), 1 kHz, 10 % THD Total RMS power 250 W FTC output power Surround Ch 34 W per channel (3 ), 120 Hz to 20 kHz, 1 % THD Total FTC power 68 W [RF\SECTION] Wireless module Frequency range No. of channels
2 way, 2 speaker system (Bass reflex) Impedance 6 6.5 cm (21/2z) Cone type 6.5 cm (21/2z) Cone type 250 W6 (Max) 82 dB/W (1.0 m) 5 kHz 80 Hz to 25 kHz (j16 dB) 96 Hz to 22 kHz (j10 dB) 270 mmk94 mmk95 mm (105/8zk311/16zk33/4z) 1.3 kg (2.9 lbs)
2.400 GHz to 2.4835 GHz 3
[GENERAL] Power supply [U.S.A.]and]Canada] [Others] Power consumption

Dimensions (WtHtD)

Mass [Weight]
Power consumption in off mode [U.S.A.]and]Canada] [Others]
approx. 0.2 W approx. 0.3 W
Rating with low-cut filter equipped amplifier
[Note] 1. Specifications are subject to change without notice. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by a digital spectrum analyzer.
AC 120 V, 60 Hz AC 110 V to 240 V, 50/60 Hz Digital transmitter 1.5 W Wireless system [U.S.A.]and]Canada] 35 W [Others] 43 W Digital transmitter 65 mmk52 mmk8.6 mm (29/16zk21/16zk11/32z) Wireless system 165 mmk90 mmk164 mm (61/2zk317/32zk615/32z) Digital transmitter 0.02 kg (0.04 Ibs) Wireless system 0.655 kg (1.54 Ibs)

Our Customer Care Centre:
Telephone #: 1-800 #: Fax #: Email link:
(905) 624-5505 1-800-561-5505 (905) 238-2360 Customer support on www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicentre at www.panasonic.ca : Link : ServicentresTM locator under Customer support
IF YOU SHIP THE PRODUCT TO A SERVICENTRE Carefully pack and send prepaid, adequately insured and preferably in the original carton. Include details of the defect claimed, and proof of date of original purchase.
SC-PT760-960P-PC_Body6_Eng (PX).fm Page 44 Monday, March 3, 2008

2:27 PM

Accessories
Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts. (Product numbers correct as of December 2007. These may be subject to change.) Only for U.S.A.: To order accessories, refer to Accessory Purchases on page 42. For other areas: To order accessories, call the dealer from whom you made your purchase. 1 Remote control (N2QAYB000214) 1 FM indoor antenna AC power supply cords Pipes (RSA0007-M) 2 Cords [U.S.A.]and]Canada] 2 Set of pipes (with cable) (K2CB2CB00021) [PT760] [PT954] [RYBX0182-K (white)] [RYBX0183-K (red)] 2 Speaker cables [PT760] 2 Cords [Others] (REEX0449K-2K) (K2CQ2CA00007) [PT960] [PT954] (RYBX0185-K) 1 Video cable (K2KA2BA00001) 1 Speaker cable (REEX0858) 2 Power plug adaptors \For\areas\except\U.S.A.\ [and\Canada] (K2DA42E00001) 2 Stands (with cable) [PT960] [RYPX0303-KL (white)] [RYPX0303-KR (red)] Bases 2 Bases [PT760] [PT960] 4 Bases [PT954] (RYBX0176-K)
2 Remote control batteries
2 Bases [PT960] (RYPX0206-1K2)
Screws (XTN5+10FFJK) 8 Screws [PT760] 16 Screws [PT960] [PT954] Small screws (XTB3+8JFJK) 4 Screws [PT760] [PT960] 8 Screws [PT954]
1 AM loop antenna (N1DAAAA00002)
1 Sheet of speaker cable stickers
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. DO NOT OBSTRUCT THE UNITS VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS. DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT. DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY MANNER. The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle. This product may receive radio interference caused by mobile telephones during use. If such interference is apparent, please increase separation between the product and the mobile telephone. For units with PX printed on the outer packaging THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.