Here you can find all about Paradox K32LED like manual and other informations. For example: review.
Paradox K32LED manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Paradox K32LED please write about it to help other people. [ Report abuse or wrong photo | Share your Paradox K32LED photo ]
Paradox K32LED, size: 558 KB
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Always Armed, Never Disarmed
For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions.
Limitations of Alarm Systems
We strongly advise that you review and take into consideration the Limitations of Alarm Systems document available on our website at http://paradox.com/Terms/.
Warning for Connections to Non-Traditional Telephony (e.g. VoIP)
Paradox alarm equipment was designed to work effectively around traditional telephone systems. For those customers who are using a Paradox alarm panel connected to a non-traditional telephone system, such as "Voice Over Internet Protocol" (VoIP) that converts the voice signal from your telephone to a digital signal traveling over the Internet, you should be aware that your alarm system may not function as effectively as with traditional telephone systems. For example, if your VoIP equipment has no battery back-up, during a power failure your system's ability to transmit signals to the central station may be compromised. Or, if your VoIP connection becomes disabled, your telephone line monitoring feature may also be compromised. Other concerns would include, without limitation, Internet connection failures which may be more frequent than regular telephone line outages. We therefore strongly recommend that you discuss these and other limitations involved with operating an alarm system on a VoIP or other non-traditional telephone system with your installation company. They should be able to offer or recommend measures to reduce the risks involved and give you a better understanding.
WARNINGS: Information to User
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to equipment intermittently, the user is encouraged to try to correct the interference by one or more of the following measures: (1) re orient or relocate the receiving antenna; (2) increase the separation between the equipment and receiver; (3) connect the equipment to an outlet on a circuit other than the one to which the receiver is connected, or (4) consult the dealer or an experienced radio/tv technician for assistance. CAUTION: The user is cautioned that any changes or modifications not expressly approved by Paradox Security Systems could void the users authority to operate/use the equipment.
One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406. Canadian and international patents may also apply. 2008 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. Esprit, Esprit E55 and Esprit E65 are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries.
If you are forced to arm or disarm your system, entering the user code with the duress option enabled will arm or disarm the system and immediately transmit a silent alert (Duress Code) to the monitoring station. The duress code must be enabled by your installer.
User Code Length
Your system can be programmed to use either 4- or 6-digit user codes, where each digit can be any value from 0 to 9. Six-digit codes are considered more difficult to crack and therefore, more secure. Avoid programming simple or obvious user codes, such as your telephone number, address, or codes such as 1234.
Adding / Modifying a User
How do I add / modify a user? 1 Press the [ ] key. 2 Enter your [MASTER CODE]. Select a user by entering a 2-digit user number (01 to 32). Enter a 4- or 6-digit [USER CODE]. Confirm the code. Press [ENTER]. Go to step 3 or press [CLEAR] to exit. For partitioned systems, go to step 7. 7 Press  and/or  to assign the user to a partition. 8 Press [ENTER]. Go to step 3 or press [CLEAR] to exit. Visual Feedback [ ] and  flash. When a number on the keypad is lit, the user is already programmed. Arm flashes. Sleep flashes. Stay flashes. Off flashes.
Deleting a User
How do I delete a user? 1 Press the [ ] key. 2 Enter your [MASTER CODE]. 3 Select a user by entering a 2-digit user number. 4 Press and hold the [SLEEP] key until you hear the confirmation beep.
Setting the Time & Date
How do I set the time & date? 1 Press the [TBL] key. 2 Press . 3 Enter time using the 24 hour format (e.g. 18:00 for 6:00 pm). 4 Enter the year (4 digits). 5 Enter the month (2 digits). 6 Enter the day (2 digits). You have now set the time & date. Press [CLEAR] to exit.
Setting Chime Zones
A chime-enabled zone will advise you every time it is opened by causing your keypad to beep. Each keypad must be chimed separately. How do I chime zones? For K636 & K10LED keypads: press & hold the zone key ( to [0(10)]) you wish to chime. For K32 & K32I keypads: press & hold the [ ] key and enter the 2-digit zone number. Confirmation beep = Chime on, Rejection beep = Chime off NOTE: For a description of the confirmation and rejection beeps, see Keypad Feedback on page 6. To identify your keypad, see page 7.
Your alarm system continuously monitors several trouble conditions that can be reported directly to your monitoring station. When a trouble condition occurs, the [TBL] key will illuminate. Press the [TBL] key, and the keypad will illuminate a number corresponding to the trouble the system is experiencing. We strongly suggest that you inform your monitoring station of the trouble and allow them to service your system. NOTE: If the keypad emits a BEEP every 5 seconds whenever a new trouble condition has occurred, press the [TBL] key to stop the Trouble Beep.
Accessing the Trouble Display Key / LED Trouble Type Lit
Power Trouble (press  to view Three types of power trouble: the type of power trouble; the  The control panel is experiencing low/no battery. corresponding key illuminate)  There is an AC failure on the control panel.  There is an auxiliary overload on the control panel.  Bell Trouble There is a bell disconnect/overload on the control panel.  Communication Trouble Your alarm system, if monitored, could not Press communicate with the monitoring station. [TBL]  Tamper/Zone Wiring Failure A wiring problem is occurring on one or more zones.  Module Tamper Trouble A modules anti-tamper switch has been triggered.  Timer Loss Your alarm systems clock must be reprogrammed. See Setting the Time and Date above to set your systems time and date. [0 (10)] Module Supervision Loss One or more modules are no longer communicating with the control panel. IMPORTANT: Except for the Timer Loss trouble, contact your monitoring station or installer to resolve the trouble condition.
When you enter information on the keypad, it will guide you with beep tones that communicate confirmation or rejection of your entries. You should be familiar with these two keypad beep tones: Confirmation Beep: When an operation (e.g. arming/disarming) is successfully entered on the keypad or when the system switches to a new status/mode, the keypad produces an intermittent beep tone (BEEP-BEEP-BEEPBEEP). Rejection Beep: When the system reverts to its previous status or when an operation is incorrectly entered on the keypad, it will emit a continuous beep tone (BEEEEEEEEP). The following are other types of auditory feedback, and will always be accompanied by the flashing of an arm key or LED ([ARM], [STAY], or [SLEEP]): Continuous beep = Alarm Variable beep = Fire alarm Intermittent beep = Beginning of exit delay Fast Intermittent beep = Last 10 seconds of exit delay
The keypad includes colored lights which convey the current status of your system. The state of each light represents a specific condition in your system. NOTE: Many of the features in your system must be enabled by the installer. If the feature is not programmed, the keypad will emit a rejection beep and the action will be cancelled. Refer to Zone Settings on page 3 for details.
When muted, the keypad will only emit the confirmation beep and rejection beep, and will beep when a key is pressed. Therefore, when muted, the keypad will not beep during an alarm and will not beep for chime enabled zones. Each keypad must be muted separately. How do I mute the keypad? Press & hold the [CLEAR] key for 6 seconds to enable or disable keypad muting. If the keypad emits a confirmation beep, Keypad Muting is enabled for that keypad. If the keypad emits a rejection beep, the feature is disabled.
The illumination level behind the keys can be modified to suit your needs. The [MEM] key is used to set the desired level. Each consecutive push of the [MEM] key will increase the backlight level until the maximum level is reached. After reaching the maximum level, the backlight level will return to the lowest level (backlight off) and the whole process is repeated. How do I modify the backlight? 1 Press and hold the [MEM] key. The [MEM] key will illuminate. 2 Press the [MEM] key to set the desired backlight level. 3 Press [CLEAR] twice to exit.
K636 Keypad Overview
[TBL] Trouble display
ON = Trouble(s) occurring (page 5)
[ARM] (page 10) [SLEEP] (page 10) [STAY] (page 11)
ON = System armed OFF = Zone disarmed Flash = Exit Delay Fast Flash = Exit Delay (final 10 sec.) / zone in alarm
[MEM] Alarm memory display
ON = Alarm(s) occurred (page 13)
[BYP] Bypass programming
ON = Zone(s) bypassed (page 13)
The keys  to [0(10)] correspond to zones 1 to 10 respectively: Key lit = Open or entry delay Key flash = In alarm
IMPORTANT: If installed on a partitioned system, the K636 will only display partition 1.
= Press once + [MASTER CODE] for Quick Menu Programming. (see Master Quick Menus on page 21)
Off Key (red): ON = Disarmed OFF = System armed Light (AC): ON = Power on OFF = Power off
StayD Light: ON = StayD on OFF = StayD off (see StayD Mode on page 9)
Esprit E55 / E65 9
Leaving the site without changing arm mode:
[OFF] for 2 sec. Press and hold the [OFF] key for 2 seconds on a keypad to leave the site without changing arm mode.
Advanced StayD Settings
Window Mode and Re-arm Delay
In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. To enter Window mode, press [OFF], then your [USER CODE]. All zones that can be opened flash. The system will start an exit delay, allowing you to open an exterior zone such as a window or a door. The system will only allow you to open one zone as the exit delay will end after doing so. When you close the open zone (window, door, etc.) that zone will re-arm. When closing an exterior zone such as a window or door, a delay will start allowing you to close the zone properly. The re-arm delay starts when you close the zone, and you must keep the zone closed for the entire delay period for it to re-arm. This is especially useful for windows that stick thus reducing false alarms.
Live View Mode:
During an alarm, press the [CLEAR] key to view the movement. The zone lights on the keypad will show the opening and closing of zones as they occur.
Arming & Disarming
Take full advantage of your system by familiarizing yourself with all the arming methods. If your system is not partitioned (see Partitioning on page 19), everything is considered as belonging to Partition 1. NOTE: If you cannot arm because a zone is open, the system will enter in Bypass Programming. Enter the two digit zone you wish to bypass and press [ENTER], or press [ENTER] to bypass all open zones.
This method will arm all the zones in the selected partition. Please note that Regular arming can also be activated using Auto-Arming (see Auto-Arming on page 12) or One-Touch Arming (see One-Touch Arming on page 12). How do I Regular arm? 1 Close all zones in the desired partition. 2 Press [ARM] + [USER CODE]. 3 If you have access to both partitions (see Partitioning on page 19): Press the key corresponding to the desired partition ( or ). For both partitions, press the other key after the confirmation beep.
Similar to Stay arming, Sleep arming allows users to remain in a protected area, but provides a higher level of protection. For example, in a two-story house, the perimeter is protected with Stay arming. With Sleep arming, the perimeter as well as the main floor are protected (motion detectors, etc.), allowing you to roam the second floor and sleeping quarters. Sleep zones are zones that are bypassed when Sleep arming. For example, when you go to sleep at night, the entire premises except your bedroom is fully armed. Sleep arming can also be activated using Auto-Arming (see Auto-Arming on page 12) or One-Touch Arming (see One-Touch Arming on page 12). How do I Sleep arm? 1 Close all zones in the desired partition (except Sleep zones). 2 Press the [SLEEP] key. 3 Enter your [USER CODE]. 4 If you have access to both partitions (see Partitioning on page 19): Press the key corresponding to the desired partition,  or . For both partitions, press the other key after the confirmation beep.
If an alarm has occurred on a zone, the respective zone key will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective keys will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. When the system is disarmed, the zone keys will turn off, while the [MEM] key remains lit. Press the [MEM] key to illuminate the key corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm occurs and after a valid code is entered or upon full-arming the system.
Disarming & Deactivating an Alarm
To disarm an armed system or an alarm, press [OFF] and enter your [USER CODE]. An entry point, like the front door, will be programmed with one of two Entry Delay Timers. When an entry point is opened, the keypad will beep until you disarm the system. Your alarm system will not generate an alarm until this timer elapses. Any user can disarm a partition they have been assigned to, except users assigned with the Arm Only Option or PGM Only Option. How do I disarm the system? Press [OFF] + enter [USER CODE].
In case of an emergency, the system can provide three panic alarms that can immediately generate an alarm after simultaneously pressing and holding two specific keys for three seconds. Based on your needs, these panic alarms can generate audible alarms (sirens or bells) or silent alarms and can communicate specific messages to your monitoring station. For instance, pressing  and  can mean call the police or anything you require. This feature must be set by your installer. Press and hold keys  and  for Panic type 1 (e.g. police). Press and hold keys  and  for Panic type 2 (e.g. medical). Press and hold keys  and  for Panic type 3 (e.g. fire).
Upon a fire alarm, the bell/siren will emit three squawks at 2 second intervals until silenced or reset by entering a valid user code. If the zone is a Delayed Fire Zone, there is a delay before the system contacts the monitoring station. This will prevent unnecessary reporting of false alarms. If there is no fire condition, contact your monitoring station immediately to avoid an unnecessary response. What do I do if a delayed fire zone was set off accidentally? 1 Press the [CLEAR] key within 30 seconds of the alarm. 2 Try to correct the problem. 3 If the problem persists, after 90 seconds, the alarm will sound again. Press the [CLEAR] key again.
Minimizing Fire Hazards
The three most common causes of fires: Cooking is the leading cause of home fires in the U.S. It's also the leading cause of fire injuries. Cooking fires often result from unattended cooking and human error, rather than mechanical failure of stoves or ovens. Careless smoking is the leading cause of fire deaths. Smoke detectors and smolder-resistant bedding and upholstered furniture are significant fire deterrents. Heating is the second leading cause of residential fires. However, heating fires are a larger problem in single family homes than in apartments since the heating systems in single family homes are often not professionally maintained.
Fire Safety Tips
In the event of a fire, escape first, then call for help. Develop a home fire escape plan and designate a meeting place outside. Make sure everyone in the family knows two ways to escape from every room. Practice feeling your way out with your eyes closed. Never stand up in a fire, always crawl low under the smoke and try to keep your mouth covered. Never return to a burning building for any reason; it may cost you your life. Finally, having at least one working smoke alarm dramatically increases your chances of surviving a fire. And remember to practice a home escape plan frequently with your family.
Providing a Fire Warning System
Household fires are especially dangerous at night. Fires produce smoke and deadly gases that can overcome occupants while they sleep. To warn against fire, smoke detectors should be installed outside each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements.
Testing & Maintenance
With the system disarmed and the OFF light illuminated, activate motion detectors by walking in the protected area. Open and close protected doors and verify that the corresponding lights illuminate. Your installer can advise you of the best way to test your particular system. Do not use open flame or burning materials to test your fire detection devices. Contact your installer for safe methods of testing your system. Under normal use, your system requires virtually no maintenance other than regular testing. It is recommended that the standby battery be changed every three years. Speak to your installer about the necessary tests and how often they should be performed.
Communicating Through the Internet (IP100)
You can communicate with your security system via the internet by using a system accessory called the IP100 Internet Module (sold separately). The IP100 controls and monitors your security system remotely through any web browser. It allows for E-mail notifications of important system events such as alarms, arm/ disarm events, and troubles. For example, receive an E-mail at work when your kids get back from school, or if an alarm occurs in your system at home.
You can also view live status of your system and arm/disarm your system. For example, you have just left your office for the weekend but are not sure you remembered to arm it. Simply check the status of your system from a laptop and arm it remotely. There is no PC software to install, as the IP100 is web-based. It uses a userfriendly web-page that puts you in control. Consult your installer or refer to the IP100 User manual for more information.
Communicating Using Text Messages (PCS100)
You can communicate with your security system using text messages (SMS) by using a system accessory called the PCS100 GSM Module (sold separately). The GSM module allows you to receive text messages of system events, such as alarms or troubles, on your cellular phone. It also allows you to send text messages to arm or disarm your system from anywhere in the world. Consult your installer for more information.
Receiving Text Messages
To receive text messages from your system you need to: Program the telephone numbers you wish to receive text notifications. Select which event groups (alarm, arm/disarm, trouble and trouble restore) will generate text messages. Select which partition the phone number is assigned to. How do I set up the GSM module to send me text messages? 1 Press the [ ] key. 2 Enter [MASTER CODE]. 3 Press [ARM]. 4 Using the [ ] / [SLEEP] and [ ] / [STAY] keys or by entering  to , select one of the eight telephone numbers you wish to program and press [ENTER]. 5 Enter the telephone number and press [ENTER]. 6 Select the which group of events will send a text message to the phone number set in step 5 (see Event Call options below). 7 Press [ENTER]. 8 Select which partition(s) is assigned to this telephone number by pressing , , or both. 9 To save, press [ENTER].
Event Call Options
Option     Events that send a text message Any alarm (e.g. fire, burglary etc.) Arming and disarming Any trouble (e.g. battery loss) Any trouble restore (e.g. battery restored)
Sample Text Messages
Alarm message Arming / disarming message Trouble message Trouble restore message
Sending Text Messages to Arm / Disarm
You can arm or disarm the system by sending a text message (SMS) from any cell phone. The message must be sent to the GSM modules phone number, as determined by the cell phone provider (consult your installer for more information). Text message commands have a specific format which follows this pattern: C[USER CODE].[ACTION].A[PARTITIONS].[PHONE NUMBER] NOTE: SMS commands must be entered in capital letters. Example:C1234.ARM.A1.5555551234 C1234.OFF.A1.5555551234 In the example above, user code 1234 will arm or disarm partition 1, and the confirmation message will be sent the following phone number: (555) 555-1234. User Code The first part of the text message is the user code (same code used on the alarm system). It must be prefaced with the letter C and followed by a period. Example:C1234. Action It is possible to arm or disarm the system. The command must be entered after the user code and followed by a period. To arm the system, enter the ARM command. To disarm the system, enter the OFF command. Example:C1234.ARM. Partition It is possible to arm or disarm specific partitions. The partitions must be prefaced by the letter A, and separated by commas for individual partitions. It is also possible to affect a series of partitions by writing TO between the start and end partitions of that series. The list of partitions must be followed by a period. Examples:C1234.ARM.A1. C1234.ARM.A1TO2. Phone Number This informs the system of which phone number must be notified by SMS to confirm the status change. Example:C1234.ARM.A1,3,5TO7.5555551234 IP Information It is possible to receive the IP address of the GSM module via text message. The GSM module will then send a text message to the specified phone number displaying the IP address of the GSM module. A valid user code must be entered to receive the IP address. The IP address can be used to configure remote software. Consult your installer for more information. Example:C1234.IP.5555551234
Your system is equipped with a partitioning feature that can divide your alarm system into two distinct areas identified as Partition 1 and Partition 2. When partitioned, each zone, each user code and many of your system's features can be assigned to either Partition 1, Partition 2, or both partitions. NOTE: If the system is not partitioned, all zones, user codes, and features will be recognized as belonging to Partition 1. Partitioning is not available when using a K636 keypad.
Quick Function Keys
Upon request of your installer or monitoring station you may have to perform one of the following. To enter Menu Programming, press [ ] and then enter your [MASTER CODE]. In Menu programming, press:
[MEM] +  If your system is monitored by a monitoring station, this feature will send a test report code to the monitoring station.
[MEM] +  Will initiate a call to the monitoring station that is using the WinLoad software.
[MEM] +  Will force your security system to answer a call made by your monitoring station that is using the WinLoad software.
[MEM] +  Cancels all communication with the WinLoad software if it has been initiated.
Is this system partitioned? Yes No Partition 1 = __________________________________________ Partition 2 = __________________________________________
Special Keys and Features
[ARM] One-Touch Regular arming is activated [STAY] One-Touch Stay arming is activated [SLEEP] One-Touch Sleep arming is activated [BYP] One-Touch Bypass Programming is activated
 &  Police or_____________
Off Off Off
 &  Aux. or_______________ Audible  &  Fire or_______________ Audible
PGM 1 ______________________________
PGM Utility Keys
 & : _____________________________  & : _____________________________  & : _____________________________ [CLEAR] + [ENTER] = Smoke Reset
 & : _____________________________  & : _____________________________  & : _____________________________
Enter and exit your premises through the designated doors. Exit Delay 1 (Partition 1): _______sec. = time to exit premises Exit Delay 2 (Partition 2): _______sec. = time to exit premises Entry Delay 1 = _______sec. = time to disarm before alarm; enter through zone #___________ Entry Delay 2 = _______sec. = time to disarm before alarm; enter through zone #___________ Alarm will activate siren or bell for ______ min.
Installed by:_______________________________________________________ Date: ________________________________ Serviced by:_______________________________________________________ Telephone: ____________________________ Monitored by:______________________________________________________ Telephone: ____________________________ Your account number: _______________________________________________ Alarm transformer location:___________________________________________ On circuit #:____________________________ Location of Telephone Connections:____________________________________
Master Quick Menus
Step Action [ ] + [MASTER CODE] [USER NUMBER] [CODE] [CONFIRM CODE] [ENTER]  and/or  + [ENTER] Details The [ ] key will flash. LED/key on = programmed user. [PARTITION MASTER CODE] may also be used. 2 digits: 01 to 32. Enter a 4 or 6-digit code. Re-enter 4 or 6-digit code. Press [ENTER]. Goes to the next available user, or if partitioned, go to step 6. Assign the user to one or both partitions and press [ENTER]. By default, users are assigned to partition 1. Goes to next available user.
Step 3 Action [ ] + [MASTER CODE] [TBL]  = Entry Delay 1 (sec.)  = Entry Delay 2 (sec.)  = Exit Delay (sec.)  = Bell Cut-Off (min.)  to  Details The [ ] key will flash. Default = 045 sec. Default = 045 sec. Default = 060 sec. Default = 004 min. ___/___/___ Enter a value between 000 and 255
Time and Date
Step 5 Action [ ] + [MASTER CODE] [TBL]  [HH:MM] [YYYY/MM/DD] Details The [ ] key will flash.
Enter time using the 24 hour format (e.g. 18:00 for 6:00 pm). Enter date.
Communicate with WinLoad
Step 3 Action Details The [ ] key will flash. [ ] + [MASTER CODE] [MEM]  = Start communication  = Cancel communication
Step 3 Action [ ] + [MASTER CODE] [MEM]  = Personal Phone #1  = Personal Phone #2  = Personal Phone #3  = Personal Phone #4  = Personal Phone #5  = Pager # [PHONE #] + [ENTER] [MESSAGE] + [ENTER] Details The [ ] key will flash.
Enter phone # (up to 32 digits) and press [ENTER]. Goes to next phone#, or go to step 5 if  = Pager # was selected. Step 5 for Pager # only. Enter pager message and press [ENTER].
Step 3 Action [ ] + [MASTER CODE] [MEM]  Details The [ ] key will flash. Press the [MEM] key. Send a test report to the monitoring station.
Step 5 Action [ ] + [MASTER CODE] [BYP]  = Auto arm (partition 1)  = Auto arm (partition 2) [HH:MM]  = Regular arm  = Sleep arm  = Stay arm Details The [ ] key will flash.
Enter time using the 24 hour format (e.g. 18:00 for 6:00 pm).
Step 3 Action [ ] + [MASTER CODE] [BYP]  = Regular arm  = Sleep arm  = Stay arm Details The [ ] key will flash. Toggle to have the siren squawk on arm/disarm with keypad.
Access Code Length...4 Adding a User..4 Advanced StayD...10 Advanced System Features..19 Alarm Display...13 Alarms...13 Arming...10 Arming & Disarming...10 Arming & Disarming with StayD..9 Auditory Feedback..6 Auto Arm...22 Auto-Arming...12 Internet... 14 IP100... 14
K10LEDV/H... 8 K32I.... 7 K32LED... 8 K636... 7 Keypad.... 7 Keypad Backlight... 6 Keypad Feedback.. 6 Keypad Muting... 6 Keypads... 6 Keys... 19
Backlight...6 Bypass Recall...11 Bypass Recall Feature...11 Bypassing a Zone...11
Limitations.. 0 Live View Mode.. 10
Chime Zones...5 Communicate...21 Communicating by Phone (VDMP3).17 Communicating Through the Internet (IP100).14 Communicating Using Text Messages (PCS100)..15 Communicator...22
Maintenance.. 14 Manual Bypass... 13 Master Code... 4 Master Codes.. 4 Master Quick Menus.. 21 Messages... 15
Date....5 Deactivating an Alarm..13 Delays....21 Deleting a User...4 Diagram...18 Disarming...10, 13 Display...13 Duress Code...4
No Movement Auto Arming.. 13
One-Touch Arming.. 12 One-Touch Bypass Programming.. 12 One-Touch Force Arming.. 12 One-Touch Stay Arming.. 12 Overviews.. 7
Event Call Options...15
Panic Alarms.. 13, 20 Partitioning... 19 PCS100... 15 PGMs.... 19 Programmable Outputs.. 19
Feedback...6 Fire Alarms...14 Fire Hazards..14 Fire Safety...14 Function...19
Quick Function Keys.. 19 Quick Programming.. 21
GSM Module Phone Number..16, 20
Re-arm Delay... 10 Receiving Text Messages... 15 Regular... 10 Regular Arming.. 10
Sample Text Messages..15 Sending Text Messages to Arm/Disarm..16 Settings....2 Sleep Arming...10 SMS Event Call Options..15 Special Keys..19 Stay Arming...11 StayD...9 System Master Code...4 System Notes...19 System Options..22 System Timers...20
Table of Contents...1 Test Report...22 Testing...14 Text...15 Time & Date...5 Time and Date...21 Timed Auto Arming..12 Trouble....5 Trouble Display...5
User...21 User Codes...4 User Settings...2 Utility Keys...20
VDMP3...17 VDMP3 Instructions...18 Visual Feedback...6
WARNINGS...0 Window Mode...10 WinLoad...21
Zone...19 Zone Setting...3 Zone Settings..3
We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit us at www.paradox.com.
Printed in Canada - 09/2008 EX5-EU00
Powershot S100 Antivirus 4 Siemens SL42 Ypt-400 WHP 990 JT-P770 AVR 130 H 4250 KX-FL511 R-7A53 NV-F75B XR-7850 PV-750 Plus LH-T502SH F1409TDS FW-C870 Iseos EL-531G 4 5 Seiko 7S36 M1713 L1742T-BF 360 Review 2033SW DV-SP403E 20-5102 GR-DVL157 Samsung E258 005736-0 Gpsmap 76S HP-137R U7142 AG-HMC41 Ifinder Hunt 775VM800 KP-53S4U EMP 100 PL-PRO-E K8upgrade-760GX Sport 197 V5000 WIL 11 Illustrator 10 Plw225s399 BX625FWD Scroll SAW Mini 110 Ecmp10 RDA-7 1 F-Z94 Color 1160 I865GM-7L Diva P90 Picturetel 210 VRX756VD EDE419M Smart Coolpix 880 Arxd 109 TTR125-2007 ICF-M60lrds Slider Phonefax 33S 4720Z VGN-CR31s W SRT 6126 CT-S280 Daihatsu BJC-4550 Backgammon LAV48580 SA-EX100 DVP-NS575PB Binatone E800 CD245 DP-01 Inventor 2010 Series LK-220 2253LW MAC 542E 12693 A-6000 Program Terminal Edition 883 LOW KX-T7531 SUP 016 CLP-820 MS-6577 Sdec-2500 PM-D870 KLR 100 World 242 2-5 50 2T Caplio R2 953BW LRH-790
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101