12 Reference & Installation Manual
Advanced Technology Zone (ATZ) Connections
The ATZ feature is a software oriented feature that enables two detection devices to be installed per hardwired input terminal. Each detection device has its own zone, displays its zone status on the keypad and sends its own alarm codes. Fire zones cannot be doubled. Figure 4: Advanced Technology Zone Connections

Magellan / Spectra SP 13

Fire Circuits
When a zone is programmed as a fire zone, the zone becomes normally open and requires an EOL resistor. If a line short occurs or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel will generate an alarm. If a trouble occurs on a fire zone, the Fire Loop Trouble will appear in the keypads trouble display (see Trouble Display on page 57) and the control panel can transmit the Fire Loop Trouble report, if programmed, in section [866]. Figure 5: Fire Circuits

2.17.1

4-Wire and 2-Wire Installation:
For 4-wire installation, program the Activation Event so that the smoke detectors can be reset by pressing the [CLEAR] + [ENTER] keys for three seconds. See Event Group # 6 in the Event Description list in the programming guide. For 2-wire smoke detector installation, connect the 2-wire smoke detectors. If a line short occurs or the smoke detector activates, whether the system is disarmed, the control panel will generate an alarm. If the line is open, the Zone Fault trouble indication appears on the trouble display and the report code is sent to the monitoring station, if programmed. To reset 2-wire smoke detectors, press the [CLEAR] + [ENTER] keys for three seconds.
14 Reference & Installation Manual
Part 3: Programming Methods
3.1 WinLoad Software for Windows
Program the control panels remotely or on-site using the WinLoad Software (V2.80 or higher) for Windows. For more information, contact your local Paradox Distributor or visit our web site at paradox.com. If you are using the WinLoad software, you must program the features (see Settings for WinLoad Software on page 55). Update the panels firmware by connecting it to a PC via a 306 Direct Connect Interface and then using the Winload software. (Not investigated by UL).

Entry/Exit Paths

StayD consists of programmed pathways, where the user enters and exits the property through pre-defined routes, with only the routes respective zones open for passage. A path can be programmed for each individual keypad, with a maximum of four zones per path. Path zones must be defined as follow or delay zones only. StayD is automatically enabled when a path is programmed to a keypad. The first zone programmed in a path is its designated entry point (e.g. doors, garage). Designated entry points are not common to multiple paths. There is only one designated entry point per path. Also, they are only used when entering/exiting with a remote control (see below). The system only disables the path zones corresponding to the keypad at the point of entry/exit, while re-arming as you enter/ exit. If another path zone opens before trying to disarm the system, you can validate the zone by entering your user code. For example, you have entered your home through Path 1 and are at your keypad. Before disarming the system, you notice a Path 2 zone has opened. If you know it is a member of your family and would like to validate the open zone, enter your user code. All paths, including Path 1, will subsequently be validated. If the path 2 zone opens after you have entered your code to validate Path 1, you must enter your code again to validate Path 2. You must enter your code for every zone that opens that is not part of any path. For example, if you have entered through Path 1 and a non-path zone opens, you must enter your code once to validate your path and once for the non-path zone. If you do not validate the non-path zone, the system will fall in alarm.

Entry/Exit with a Keypad

When entering with a keypad, the path zones will fall into entry delay, allowing you to reach the keypad. Use the keypad to disarm the system and switch to Stay arm mode. When exiting with a keypad, only the path zones will fall into delay (same as exit delay), allowing you to leave while the rest of the premises remains secure.

Viewing the Wireless Transmitter Signal Strength
Sections [101] to [132] Once wireless transmitters have been installed and assigned to the control panel, the signal strength of each transmitter can be verified in sections [101] to [132]. Each section represents the signal strength viewer for a specific device. For example, section [101] is the viewer for zone 1 and section [132] is the viewer for the zone 32. Sometimes moving the transmitter or control panel by a small amount will greatly increase the signal reception. How Do I View a Wireless Transmitters Signal Strength? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) 3) Enter the desired [SECTION NUMBER] (from sections [101] to [132]). 4) Press the transmitters anti-tamper switch or open the corresponding zone. 5) The keypad will illuminate numbers 1 to 10. Signal Strength Indicator 8 to 10 / 3 beeps = Best signal
5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)

Supervision Options

The Supervision Options cannot be used with any remote controls assigned to the control panel.
Supervision Bypass Options
Section [705]: Arming/Disarming Options Option [8] ON = Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone (default) Option [8] OFF = No Supervision Loss if detected on a Bypassed Wireless Transmitter Zone When this feature is disabled, the Wireless Transmitter Supervision Options will follow the zones bypass definition. This means the control panel will not perform any action if a Supervision Loss occurs on a bypassed zone. When this feature is enabled, the Wireless Transmitter Options will ignore the bypass definition. This means the control panel will generate an incident as per Wireless Transmitter Supervision Options if a supervision loss occurs on a bypassed zone.
30 Reference & Installation Manual
RF Supervision Timer Settings
Section [706]: Supervision Options Option [1] OFF = Check-in supervision interval is every 24 hours (default) Option [1] ON = Check-in supervision interval is every 80 minutes Option [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless transmitters. For example, if the timer is set to 80 minutes (option [1] = ON), the control panel will expect a check-in status signal to be sent from its assigned wireless transmitters within 80 minutes. If the control panel does not receive a signal from one of its wireless transmitters within the period of time defined here, it can then generate a trouble, an alarm, and/or can transmit a report code to the monitoring station (see Supervision Options on page 30).

Wireless Repeater Options
Section [587]: Wireless Repeater Options Option [1] OFF Option [1] ON = Repeater 1 Supervision Disabled = Repeater 1 Supervision Enabled (default)
Option [2] OFF = Repeater 2 Supervision Disabled Option [2] ON = Repeater 2 Supervision Enabled (default) If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality.

Magellan / Spectra SP 33

Wireless Options
Section [551] (Repeater 1) and Section [562] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of wireless keypads in this section. Enabling these options for keypads means that the repeater will retransmit any signals relevant to them. Option [1] OFF Option [1] ON Option [2] OFF Option [2] ON Option [3] OFF Option [3] ON Option [4] OFF Option [4] ON Option [5] OFF Option [5] ON Option [6] OFF Option [6] ON Option [7] OFF Option [7] ON Option [8] OFF Option [8] ON = Repeat Wireless Keypad 1 Signals (default) = Repeat Wireless Keypad 1 Signals = Repeat Wireless Keypad 2 Signals (default) = Repeat Wireless Keypad 2 Signals = Repeat Wireless Keypad 3 Signals (default) = Repeat Wireless Keypad 3 Signals = Repeat Wireless Keypad 4 Signals (default) = Repeat Wireless Keypad 4 Signals = Repeat Wireless Keypad 5 Signals (default) = Repeat Wireless Keypad 5 Signals = Repeat Wireless Keypad 6 Signals (default) = Repeat Wireless Keypad 6 Signals = Repeat Wireless Keypad 7 Signals (default) = Repeat Wireless Keypad 7 Signals = Repeat Wireless Keypad 8 Signals (default) = Repeat Wireless Keypad 8 Signals
Section [552] (Repeater 1) and Section [562] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them. Option [1] OFF Option [1] ON Option [2] OFF Option [2] ON Option [3] OFF Option [3] ON Option [4] OFF Option [4] ON Option [5] OFF Option [5] ON Option [6] OFF Option [6] ON Option [7] OFF Option [7] ON Option [8] OFF Option [8] ON = Repeat Wireless Zone 1 Signals (default) = Repeat Wireless Zone 1 Signals = Repeat Wireless Zone 2 Signals (default) = Repeat Wireless Zone 2 Signals = Repeat Wireless Zone 3 Signals (default) = Repeat Wireless Zone 3 Signals = Repeat Wireless Zone 4 Signals (default) = Repeat Wireless Zone 4 Signals = Repeat Wireless Zone 5 Signals (default) = Repeat Wireless Zone 5 Signals = Repeat Wireless Zone 6 Signals (default) = Repeat Wireless Zone 6 Signals = Repeat Wireless Zone 7 Signals (default) = Repeat Wireless Zone 7 Signals = Repeat Wireless Zone 8 Signals (default) = Repeat Wireless Zone 8 Signals
Section [553] (Repeater 1) and Section [563] (Repeater 2): Wireless Repeater Options Enable or disable the repetition of zone signals in these sections. Enabling these options for zones means that the repeater will retransmit any signals relevant to them. Option [1] OFF Option [1] ON Option [2] OFF Option [2] ON Option [3] OFF Option [3] ON Option [4] OFF Option [4] ON Option [5] OFF Option [5] ON = Repeat Wireless Zone 9 Signals (default) = Repeat Wireless Zone 9 Signals = Repeat Wireless Zone 10 Signals (default) = Repeat Wireless Zone 10 Signals = Repeat Wireless Zone 11 Signals (default) = Repeat Wireless Zone 11 Signals = Repeat Wireless Zone 12 Signals (default) = Repeat Wireless Zone 12 Signals = Repeat Wireless Zone 13 Signals (default) = Repeat Wireless Zone 13 Signals

Sleep Arming switches to Sleep Force Arming
Section [704]: Arming/Disarming Options Option [3] OFF = Sleep Arming Switches to Sleep Force Arming Disabled Option [3] ON = Sleep Arming Switches to Sleep Force Arming Enabled (default) With this feature enabled, the control panel will always Sleep Force arm (if a force-enabled zone is open, see Force Zones on page 27) instead of Sleep arm when a valid user access code with the Force Arming Option is entered.
Restrict Arming on Battery Failure
Section [703]: Arming/Disarming Options Option [5] OFF = Permit arming on battery failure (default) Option [5] ON = Restrict arming on battery failure If this option is enabled, the control panel will not arm the system if the control panel detects that the backup battery is disconnected, that its fuse is blown, or that the battery voltage drops to less than 10.5V. The control panel will not arm the system until all battery trouble conditions are rectified.
Restrict Arming on Tamper Failure
Section [703]: Arming/Disarming Options Option [6] OFF = Permit arming on tamper failure (default) Option [6] ON = Restrict arming on tamper failure If this option is enabled, the control panel will not arm the system if the control panel detects a tamper trouble on one or more zones. The control panel will not arm the system until all tamper trouble conditions are rectified. This feature will not function if the tamper recognition options (see Tamper Recognition on page 41) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 42).

Magellan / Spectra SP 37

Restrict Arming on Wireless Supervision Trouble
Section [703]: Arming/Disarming Options Option [7] OFF = Permit arming on wireless supervision failure (default) Option [7] ON = Restrict arming on wireless supervision failure If this option is enabled, the control panel will not arm the system if the control panel detects a wireless supervision trouble on one or more zones. The control panel will not arm the system until all wireless supervision trouble conditions are rectified. This feature will not function if the tamper recognition options (see Tamper Recognition on page 41) are disabled or whenever the tampered zone is bypassed and the tamper bypass options have been enabled (see Tamper Bypass Options on page 42).

10.11.1 No Movement Timer
Section [749] = Partition 1, [750] = Partition to 255 x15min, Default = Disabled Select the section corresponding to the desired partition and program the interval of time without movement you wish the control panel to wait before arming and/or sending the No Movement report code. If No Movement Auto-arming is disabled, the control panel can still send the No Movement report code when no movement has been detected for the period specified by the No Movement Timer.
38 Reference & Installation Manual

Auto-Arming Options

(Not to be used with UL installations)
Section [741] = Partition 1, [742] = Partition 2 [3] OFF OFF ON [4] OFF ON OFF Regular Sleep Stay
When using Timed Auto-arming or No Movement Auto-arming, the control panel can Regular, Sleep or Stay arm the selected partition.

One-Touch Arming

Section [703]: Options [1] to [3] Option [1] ON = Press & hold the [ARM] key for One-touch Regular Arming. Option [2] ON = Press & hold the [STAY] key for One-touch Stay Arming. Option [3] ON = Press & hold the [SLEEP] key for One-touch Sleep Arming. The One-touch arming features allow users to arm the system without having to enter any access codes. To arm the system, press and hold the appropriate key (see above) for approximately 3 seconds. If the system is partitioned, you must also press the key corresponding to the partition you wish to arm.
One-Touch Bypass Programming
Section [703]: Options [4] Option [4] ON = Press & hold the [BYP] key for One-touch Bypass Programming. Bypass programming allows users to program the alarm system to ignore (deactivate) specified zones the next time the system is armed. Press and hold the [BYP] key for three seconds to access bypass programming mode.

Exit Delay

Section [745] = Partition 1, [746] = Partition to 255 seconds, Default = 60 seconds, Maximum 60 seconds for UL Listed systems After entering the required arming sequence (i.e. user access code, etc.), the exit delay parameter determines the amount of time a user has to leave the protected area before the control panel arms the partition. The exit delay applies to all zones in the selected partition. When enabled, the keypad will beep once every second during the exit delay and will beep rapidly during the final 10 seconds of the exit delay.

12.13.5 Account Numbers

Section [811]: Partition 1, Section [812]: Partition 2 All report codes are preceded by a 4-digit or 3-digit Partition Account Number to ensure correct identification in a partitioned system. Partition account numbers can be any hexa-digit from 1 to F. To enter a 3-digit account number, simply press the [SLEEP] key followed by a 3-digit account number. Also, when using 3-digit account numbers, you must use 1-digit report codes.

Dialing Method

Section [800]: Dialer Options Option [6] OFF = Pulse Dialing (see Pulse Ratio on page 47). Option [6] ON = Tone/DTMF Dialing (default)

Pulse Ratio

Section [800]: Dialer Options Option [7] OFF = European Pulse Ratio of 1:2 Option [7] ON = U.S.A. Pulse Ratio of 1:1.5 (default) When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the 1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not providing the desired results, the 1:2 ratio may be used.

Maximum Dialing Attempts

Section [831] 000 to 255 attempts, Default = 8 attempts The value programmed in section [081] determines how many times the control panel will re-dial the same monitoring station telephone number before proceeding to the next number.
Delay Between Dialing Attempts
Section [832] 000 to 255 seconds, Default = 20 seconds This delay determines the amount of time the control panel will wait between each dialing attempt. This section applies to the Plug-in Voice Dialer when using a VDMP3.
Switch to Pulse on 5th Attempt
Section [800] Option [3] OFF = Switch to Pulse on 5th Attempt Disabled (default) Option [3] ON = Switch to Pulse on 5th Attempt Enabled With option [3] ON, the control panel will switch to pulse dialing on the 5th attempt of reaching the monitoring station.

Magellan / Spectra SP 47

Alternate Dial Option
Section [800]: Dialer Options Option [4] OFF = Alternate Dial Disabled (default) Option [4] ON = Alternate Dial Enabled With option [4] OFF, the control panel will dial the backup programmed in section [817] after all attempts to one monitoring station number have failed. With option [4] ON, the control panel will dial the backup number after every failed attempt.

Force Dial Option

Section [800]: Dialer Options Option [5] OFF = Force Dial Disabled Option [5] ON = Force Dial Enabled (default) With option [5] is enabled, the panel will dial a telephone number even if no dial tone is present after 4 seconds.

Telephone Line Monitoring (TLM)
When enabled, the system verifies the existence of a telephone line once every second. A line test failure occurs when the TLM detects less than 3 volts for the period defined by the TLM Fail Timer. If the line test fails, the control panels STATUS LED flashes and generates one or more conditions as defined by the TLM settings below. These will be restored when the control panel detects the telephone line again. Please note that when the dialer detects an incoming call, the TLM test will stop for 1 minute. Section [800]: Dialer Options [1] OFF / [2] OFF: TLM Disabled [1] OFF / [2] ON: Trouble Only Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 57). [1] ON / [2] OFF: Audible Alarm If System Armed Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 57) and if the system is armed, the control panel will generate an audible alarm. [1] ON / [2] ON: Silent Alarm Becomes Audible Upon line test failure, a TLM Trouble will appear in the keypads trouble display (see Trouble Display on page 57) and causes a silent zone or silent panic alarm to switch to audible.

12.27.1 TLM Fail Timer

Section [830] 016 to 255 x 2 seconds, Default = 32 seconds If TLM does not detect the existence of a telephone line for the duration of this period, the control panel will generate the condition(s) defined by the TLM options.

Magellan / Spectra SP 49

Pager Reporting Delay
Section [834]: Communication Timers 000 to 255 seconds, Default = 20 seconds When using the Pager Reporting Format, the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the welcome message before sending data.
Pager Reporting Message Repetition
Section [835]: Communication Timers 000 to 255 times, Max. 10, Default = 3 When using the Pager Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged.

Personal Reporting Delay

Section [836]: Communication Timers 000 to 255 times, Max. 127, Default = 5 When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the report codes. This is to allow time for the system to provide a dial tone or to bypass the welcome message before sending data. This section applies to the Plug-in Voice Dialer when using a VDMP3.

Personal Reporting Message Repetition
Section [837]: Communication Timers 000 to 255 times, Max. 10, Default = 3 When using the Personal Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged. This section applies to the Plug-in Voice Dialer when using a VDMP3.

Disable Reporting

Sections [800] Option [1] OFF = Dialer Activated (default) Option [1] ON = No Dialer With this option disabled (default), the control panel will continue to report events. With the option enabled, reporting is disabled.
50 Reference & Installation Manual
Part 13: Programmable Outputs
A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The control panel includes two/four onboard PGMs. It can support up to a total of 16 PGMs. A Wireless PGM module can be assigned to any PGM. It will work in parallel with the Control Panel Output.

PGM Activation Event

Sections [220], [222], [224], [226], [228], [230], [232], [234], [236], [238], [240], [242], [244], [246], [248], and [250] This feature allows you to program the control panel to activate a PGM when a specific event occurs in the system. The PGM will remain in its active state until the programmed PGM Deactivation Event occurs or when the PGM Delay period elapses. For the Event List see the programming guide. To program a PGM Activation Event: 1) 2) 3) 4) Enter section that represents the desired PGM. PGM1 = [220], PGM2 = [222], etc. Enter the Event Group #. Enter the Sub-Group #. Enter the Partition # (01 = Partition = Partition = Both Partitions) The AC Loss PGM Event will only occur after the power failure report delay elapses (see Power Failure Report Delay on page 49).

PGM Deactivation Event

Sections [221], [223], [225], [227], [229], [231], [233], [235], [237], [239], [241], [243], [245], [247], [249], and [251] After PGM activation, the PGM will return to its normal state (deactivate) when the programmed PGM Deactivation Event occurs. Instead of deactivating the PGM when a specific event occurs, the PGM can deactivate after a programmed period elapses (see PGM Delay on page 51). For the Event List see the Programming Guide. If using the PGM Delay, these sections can be used as a second activation event. 1) 2) 3) 4) Enter section that represents the desired PGM. PGM1 = [221], PGM2 = [223], etc. Enter the Event Group #. Enter the Sub-Group #. Enter the Partition # (01 = Partition = Partition = Both Partitions)

Installer Function Keys

To access the Installer Function keys, press: [ENTER]+[INSTALLER CODE]+[MEM] = Test Report: Send the Test Report report code programmed in section [875] to the monitoring station. [ENTER]+[INSTALLER CODE]+[STAY] = Cancel Communication: Cancels all communication with the WinLoad software or with the monitoring station until the next reportable event. [ENTER]+[INSTALLER CODE]+[SLEEP] = Answer WinLoad Software: Will force the control panel to answer an incoming call from the monitoring station that is using the WinLoad software. [ENTER]+[INSTALLER CODE]+[BYP] = Call WinLoad Software: Will dial the PC telephone number programmed in section [915] in order to initiate communication with a computer using the WinLoad software. [ENTER]+[INSTALLER CODE]+[TBL] = Installer Test Mode: The installer test mode will allow you to perform walk tests where the siren will squawk to indicate opened zones. Press the [TBL] key again to exit.

Daylight Savings Time

Section [730]: General Zone Options 2 Option [1] OFF = Daylight Savings Time Disabled (default) Option [1] ON = Daylight Savings Time Enabled With section [730] option [1] ON, the panel adjusts the systems clock (time) for daylight savings changes. At 2:00AM on the second Sunday of a full weekend in March, the control panel will add one hour to the programmed time (clock). At 2:00 AM on the first Sunday of a full weekend in November, the control panel will subtract one hour from the programmed time (clock). By default, when section [730] is set at 18, the time is set for the US, Canada etc. For other countries see Daylight Savings Programming in the programming guide and set the country code in section [731]. Country Code List (Default = bold) 00 = US, Canada, Mexico, St.Johns, Bahamas, Turks and Caicos 01 = Cuba 02 = Brazil 03 = Chile 04 = Falklands 05 = Paraguay 06 = European Union, UK, and Greenland 07 = Russia and most states of the former USSR 08 = Australia- South Australia, Victoria, Australian Capital Territory, New South Wales 09 = Lord Howe Island- Tasmania 10 = New Zealand, Chatham 11 = Tonga 12 = Iraq and Syria 13 = N/A 14 = Lebanon, Kirgizstan 15 = Palestine 16 = Egypt 17 = Namibia 18 = USA, Canada (New Daylight Saving Time for 2007) 19 = New Zealand (New Daylight Saving Time for 2007)
Audible Trouble Warning Except AC Failure
Section [700]: General System Options Option [3] OFF = Audible trouble warning except AC failure (default) Option [3] ON = Audible trouble warning except AC failure When this option is enabled the panel will generate an audible trouble warning on all troubles except AC failure.
Audible Trouble Warning on AC Failure
Section [700]: General System Options Option [4] OFF = Audible trouble warning on AC failure (default) Option [4] ON = Audible trouble warning on AC failure When this option is enabled the panel will generate an audible trouble warning in the event of an AC failure.

Connecting to WinLoad

Computer containing WinLoad software Standard DB-9 cable (9-pin serial cable) 306 Adapter/ CONV3USB Converter 4-pin connector cable Serial Connector
56 Reference & Installation Manual

Part 16: User Operation

16.1 Alarm Display
If an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones LEDs will turn off, while the [MEM] key remains lit. Press the [MEM] key to illuminate the LEDs corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm occurs and after a valid code is entered or upon full-arming the system.

Trouble Display

Press the [TBL] key to view the Trouble Display. Please note that the keypad can be programmed to emit a beep every 5 seconds whenever a new trouble condition has occurred. Press the [TBL] key to stop the beeping. To view the sub-menu, press the corresponding key in the main menu. Main Menu Trouble [1] Wireless zone low battery [2] Power trouble Sub-Menu Trouble Menu [1] to [32] Zones in low battery [1] Low/No battery on the control panel [2] AC failure on control panel [3] Auxiliary overload on control panel [4] Wireless keypad AC failure [5] Wireless keypad battery failure [6] Wireless repeater AC failure [7] Wireless repeater battery failure [1] Bell disconnect on control panel [2] Bell overload on control panel [1] Telephone Line Monitoring on control panel [2] Fail to communicate on Monitoring Telephone 1 on control panel [3] Fail to communicate on Monitoring Telephone 2 on control panel [4] Fail to communicate on pager telephone on control panel [5] Fail to communicate on voice telephone on control panel [6] Fail to communicate with PC on control panel [1] to [32] Zones in tamper and zone wiring failure [1] MG-2WPGM [2] Keypad bus [5] Wireless keypad [1] to [32] Zones in fire loop trouble [1] to [32] Zones in supervision lost [STAY] RF interference trouble [1] MG-2WPGM [2] Keypad bus (Panel reset will not clear this trouble, clear it in section [955]) [5] Wireless keypad supervision failure [6] Wireless repeater supervision failure

Keyswitch

Arm Only...29 Definitions..29 Keyswitch Numbering...29 Maintained...29 Momentary...29 Options...29
Pager...50 Panel Answer Options...55 Panel Identifier...55 Panic...42 Panic Options..42, 51 Partial Arming Report Code..43 Partition Account Numbers...45 Partition Assignment, Zone...26 Partitioning...53 Paths...21 PC Password..55

Magellan / Spectra SP 59

PC Telephone Number.. 56 Personal... 50 Personal Dialing Numbers.. 45 PGM... 51 PGM (Control Panel) Activation Event... 51 Deactivation Event.. 51 PGM Delay... 51 PGM Activation, User Code Option.. 19 Power... 3 Power Failure Report Delay.. 49 Programmable Output Connections.. 11 Programmable Outputs... 51 Programming Methods... 15 Using a Keypad... 15 Wireless Features... 30 Pulse... 47 Pulse Ratio... 47
Report Code, System Trouble AC Failure.. 44 Auxiliary Supply... 44 Battery Failure... 44 Bell Output Disconnected... 44 Bell Output Overload.. 44 Fail to Communicate.. 44 Fire Loop Trouble.. 44 Module Fault... 44 Timer Loss... 44 Wireless Low Battery.. 44 Reporting... 50 Reporting and Dialer settings.. 43 Reporting Formats... 46 Reset, Hardware.. 53 Restrict Arming On Battery Fail.. 37 On Tamper Trouble.. 37, 38 RF Jamming Supervision.. 31 RF Supervision... 26 Rings... 55

Quick Arming.. 39

Re-arm.... 21 Recent Close Delay.. 48 Recent Closing Report Code.. 43 Recycle Alarm... 41 Regular Arming Switches to Force Arming.. 37 Remote Arming Report Code.. 43 Remote Controls Deleting... 31 Programming... 31 Programming Remote Control Buttons.. 31 Remote Disarm Report Code.. 43 Repetition.. 50 Report... 49 Report Code, Special Cold Start... 44 Installer In.. 44 Installer Out... 44 Test Report... 44 Report Code, Special Alarm Auto Zone Shutdown.. 43 Auxiliary Panic... 43 Duress.. 43 Emergency Panic.. 43 Fire Panic... 43 Keypad Lockout... 43 Recent Closing.. 43 Report Code, Special Arming Late to Close... 43 No Movement.. 43 One-Touch Arming.. 43 Partial Arming.. 43 Remote Arming.. 43 Timed Auto-Arming.. 43 Report Code, Special Disarming Cancel Auto-Arm.. 43 Remote Disarm.. 43