Entry/Exit with a Keypad

When entering with a keypad, the path zones will fall into entry delay, allowing you to reach the keypad. Use the keypad to disarm the system and switch to Stay arm mode. When exiting with a keypad, only the path zones will fall into delay (same as exit delay), allowing you to leave while the rest of the premises remains secure.
Entry/Exit with a Remote Control
When using a remote control, the path you use is defined by a designated entry point. For example: if after pressing the remote control to disarm the system you trigger zone 1, the system will check to see which path(s) include zone 1. All paths that include zone 1 will open. Only after reaching the designated entry point will the system know which path you are taking, and thus will re-arm all other paths. After entry with a remote, the system will automatically arm in Stay mode. To disarm the system with a remote control: Press once to disarm partition 1, twice for partition 2, and three times for both partitions. Press the button four times to cancel the exit delay and arm the system in Stay mode.
Window Mode and Re-arm Delay
In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. To enter Window mode, press [OFF], then your [ACCESS CODE]. All zones that can be opened flash. The system will start an exit delay, allowing you to open an exterior zone such as a window or a door. The system will only allow you to open one zone as the exit delay will end after doing so. When you close the open zone (window, door, etc.) that zone will re-arm. Re-arm Delay is a delay timer set so that when you close the open exterior zone (window, door etc.), it does not re-arm instantly. Instead the system starts the delay to allow you to close the zone properly. The delay will start every time you open the zone while trying to close it, and you must close the zone for 5 seconds for it to arm. This is especially useful for eliminating false alarms caused by windows that stick.

Advanced Settings

Section [720] Data __/__/__ (000 to 255) sec. Description Flex-Instant = Instant and follow zones will follow the delay at section [720] when Stay or Sleep armed (default is 15 seconds / 000 = instant zone). Description (000 to 255) sec. Re-arm delay (delay before zone re-arms). Default = 000 (no delay)

Section [721]

Data __/__/__

Magellan / Spectra SP 21

Part 7: Zone Programming
When programming zones, the zone assignments are dependent on the designation of the wireless transmitters, assignment of keypad zones, and the detection devices that are connected to the panel. For wireless assignment, see Wireless Transmitter Programming on page 30 or the Installer Quick Menu of the programming guide. For keypad assignment, see Configuring the Keypad Zone Number on page 16. After assigning the required zones, you must set the zones definitions, partition assignment, and options see Figure 8 below. Certain Zone Definitions change if a Flex-Instant delay is activated (section [720]). See see Zone Definition Status on page 26. Table 3: Zone Recognition Table Wireless Zone 1 Zone 2 Zone 3 Zone 4 Yes Yes Yes Yes Keypad Yes Yes Yes Yes Yes Hardwire Yes (Input Z1) Yes (Input Z2) Yes (Input Z1 with ATZ) Yes (Input Z2 with ATZ) No

Zone 5 to 32 Yes

If a zone is already programmed and you assign a device to the same zone, a wireless zone will overwrite a keypad/hardwire zone, and a keypad zone will overwrite a hardwire zone. Figure 8: Zone Programming

Zone Definitions

00 = Zone disabled 01 = Entry Delay = Entry Delay = Entry Delay 1/Stay/Sleep 04 = Entry Delay 2/Stay/Sleep 05 = Follow 06 = Follow /Stay 07 = Follow/Stay/Sleep 08 = Instant 09 = Instant/Stay 10 = Instant/Stay/Sleep 11 = Instant Fire 12 = Delayed Fire 13 = Instant Fire Silent 14 = Delayed Fire Silent 15 = 24Hr. Buzzer 16 = 24Hr. Burglary 17 = 24Hr. Hold-up 18 = 24Hr. Gas 19 = 24Hr. Heat 20 = 24Hr. Water 21 = 24Hr. Freeze 22 = 24Hr. Panic 23 = Instant No Pre-Alarm 24 = Follow no Pre-Alarm 25 = Keyswitch Maintain* 26 = Keyswitch Momentary* * On-board hardwire control panel zones only
Partition Assignment [1]- Partition 1 [2]- Partition 2 [3]- Both partitions

30 Reference & Installation Manual
RF Supervision Timer Settings
Section [706]: Supervision Options Option [1] OFF = Check-in supervision interval is every 24 hours (default) Option [1] ON = Check-in supervision interval is every 80 minutes Option [1] defines the time period that the control panel will expect a check-in status signal from its assigned wireless transmitters. For example, if the timer is set to 80 minutes (option [1] = ON), the control panel will expect a check-in status signal to be sent from its assigned wireless transmitters within 80 minutes. If the control panel does not receive a signal from one of its wireless transmitters within the period of time defined here, it can then generate a trouble, an alarm, and/or can transmit a report code to the monitoring station (see Supervision Options on page 30).

RF Jamming Supervision

Section [700]: Zone Options Option [5] OFF = RF Jamming Supervision Disabled Option [5] ON = RF Jamming Supervision Enabled (default) With option [5] ON, a trouble will be generated when the panels RF signal is jammed or encounters interference for a minimum of 10 seconds.
Wireless Serial Number Display
Section [960]: Find Wireless Serial Number Display To see the wireless serial number display, enter section [960]. Press the anti-tamper switch of the desired module to be viewed. The first digit of the serial number will illuminate on the keypad. Press [ENTER] to see each consecutive digit. Press [CLEAR] to exit.
Remote Control Programming
The control panel accepts up to thirty-two fully programmable remote controls. Programming the remote controls is accomplished in two steps: 1) Assign the remote controls to the control panel. 2) Program the buttons on the remote controls.
Assigning a Remote Control to the Control Panel
Sections [651] to [682]: Remote Controls 1 to 32 respectively Remote controls are assigned to the panel using the Automatic Learning method via the MAster Quick Menu Programming or by entering the serial number. How Do I Assign a Remote Control to the Control Panel? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) 3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]). 4) Enter the six-digit serial number of the remote.
Deleting Assigned Remote Controls
Sections [651] to [682]: Remote Controls 1 to 32 respectively Remote controls can be deleted by deleting the corresponding user (see the Quick Menu in the user guide). How Do I Delete a Remote Control? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) 3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]). 4) Press the [0] button six times to delete the serial number.

36 Reference & Installation Manual
Part 10: Arming and Disarming Options
10.1 Switch to Stay Arming if no Entry Delay is opened
Section [741]: Partition 1, Section [742] = Partition 2 Option [5] OFF = Switch to Stay Arming Disabled (default) Option [5] ON = Switch to Stay Arming Enabled If a user Regular arms a partition, but does not exit through (open and close) an entry delay zone during the exit delay, the control panel can be programmed to switch from Regular arming to Stay arming.
When Delay Zone is bypassed Follow Zones become Entry Delay 2
Section [741]: Partition 1, Section [742] = Partition 2 Option [6] OFF = Follow zones become entry delay 2 when delay zone is bypassed disabled (default) Option [6] ON = Follow zones become entry delay 2 when delay zone is bypassed enabled If a user has an entry point defined as a delay, and a motion detector set as a follow zone, this option allows the user to bypass a delay zone so that the motion detector becomes an entry delay 2 zone. For example, if a user has a malfunctioning door contact, they can bypass the delay zone and have the motion detector become an entry delay 2 zone so that they have sufficient time to disarm the system. All follow zones become entry delay 2 if at least one delay zone is bypassed.
Regular Arming switches to Force Arming
(Not to be used with UL Installations)
Section [704]: Arming/Disarming Options Option [1] OFF = Regular Arming Switches to Force Arming Disabled Option [1] ON = Regular Arming Switches to Force Arming Enabled (default) With this feature enabled, the control panel will always Force arm (if a force-enabled zone is open, see Force Zones on page 27) instead of Regular arm when a valid user access code with the Force Arming Option is entered.
Stay Arming switches to Stay Force Arming
Section [704]: Arming/Disarming Options Option [2] OFF = Stay Arming Switches to Stay Force Arming Disabled Option [2] ON = Stay Arming Switches to Stay Force Arming Enabled (default) With this feature enabled, the control panel will always Stay Force arm (if a force-enabled zone is open, see Force Zones on page 27) instead of Stay arm when a valid user access code with the Force Arming Option is entered.
Sleep Arming switches to Sleep Force Arming
Section [704]: Arming/Disarming Options Option [3] OFF = Sleep Arming Switches to Sleep Force Arming Disabled Option [3] ON = Sleep Arming Switches to Sleep Force Arming Enabled (default) With this feature enabled, the control panel will always Sleep Force arm (if a force-enabled zone is open, see Force Zones on page 27) instead of Sleep arm when a valid user access code with the Force Arming Option is entered.

Timed Auto-Arming

Section [741] = Partition 1, [742] = Partition 2 Option [1] OFF = Timed Auto-Arming Disabled (default) Option [1] ON = Timed Auto-Arming Enabled Each partition can be programmed to arm every day at the time specified by the Auto-arm Timer. The auto-arming options (see Auto-Arming Options on page 39) determine the partition's arming method. Any open zones detected when a partition is autoarmed will be bypassed regardless of their definition (except 24Hr zones). The control panel will enter a 60-second exit delay period before arming the system. At this point, auto-arming can be cancelled by entering a valid access code. Once the partition has successfully armed, the control panel can transmit the Timed Auto-arming report code programmed in section [860]. Example: To automatically arm partition 2 everyday at 6:15PM, enable Timed Auto-arming for partition 2 by turning on option [1] in section [742]. Then key in 18:15 into section [762].

10.10.1 Auto-Arm Timer

Section [761] = Partition 1, [762] = Partition 2 Select the section corresponding to the desired partition and program the time (use the 24-hour clock i.e. 6:30PM = 18:30) that you wish the control panel to attempt to arm the selected partition and/or send the Late to Close report code.

No Movement Auto-Arming

Section [741] = Partition 1, [742] = Partition 2 Option [2] OFF = No Movement Auto-Arming Disabled (default) Option [2] ON = No Movement Auto-Arming Enabled If no movement occurs in a partition's protected area for the period specified by the No Movement Timer, the control panel can automatically arm that partition. The Auto-arming Option determines the partition's arming method. Any open zones detected when a partition is Auto-armed will be bypassed regardless of their definition (except 24Hr zones). Upon arming, the control panel will transmit the No Movement report code if programmed in section [860]. Regardless of whether the system was successfully armed or not, the control panel will always transmit the No Movement report code if programmed in section [860]. If No Movement Auto-arming is disabled, the control panel will still send the No Movement report code at the time specified by the No Movement Timer. Example: To arm partition 1 whenever there is no movement for a period of 4 hours, enable No Movement Auto-arming for partition 1 by turning on the [2] Option in section [741]. Then in section [749] enter 016 (16x15min = 240min = 4 hours).
10.11.1 No Movement Timer

Flex-Instant Delay

Section [720] The Flex-Instant Delay is used to prevent false alarms when the premises is Stay/Sleep armed. In section [720] enter a 3-digit value (000 to 255, 000 = disabled) representing the number of seconds that the panel will delay an alarm allowing you to disarm the system (default 15 seconds).
42 Reference & Installation Manual
Part 12: Reporting and Dialer settings
The following section explains all the features and options that must be programmed in order for your security system to properly report system events to a monitoring station. When an event (e.g. zone in alarm) occurs in the system, the control panel verifies if a report code was programmed in the section corresponding to the event (except Ademco Contact ID All Codes). If a report code was programmed, the control panel will dial the monitoring station telephone number defined by the Event Call Direction feature. When the monitoring station answers, the control panel will transmit the System Account Code, followed by the programmed report code.

Zone Reporting Codes

Sections [141] to [172] A report code can be programmed for each of the available 32 zones. When an alarm, alarm restore, tamper, or tamper restore occurs on a zone, the control panel can send the appropriate report code to the monitoring station.

User Reporting Codes

Sections [471] to [502] A report code can be programmed for each of the available 32 users. When a user arms, disarms or cancels an alarm, the control panel can send the appropriate report code to the monitoring station.
Special Arming Report Codes
Sections [860] and [861] When the system is armed using one of the special arming features listed below, the control panel can send the appropriate report code to the monitoring station identifying how the system was armed. Section [860] Auto-Arming: A partition has armed itself at the programmed time. Late to Close: Reports every day at the time specified by the Auto-arm Timer. No Movement: No movement has been detected for the programmed amount of time in the partition. Partial Arming: A partition was Stay, Sleep, or Force armed or armed with Bypassed zones. Section [861] Quick Arming: A partition was armed using a One-touch arming feature. Arming via PC: A partition was armed using the Winload software. N/A N/A

Special Disarming Report Codes
Section [862] When using one of the special disarming features, the control panel can send the report code to the monitoring station, identifying how the system was disarmed. Cancel Auto-Arm: A partition is disarmed during the Timed Auto-arm's 60-second exit delay. Only reports if Disarming Reporting Options are set to always report disarming. Disarming via PC: System is disarmed using the WinLoad software. Only reports if Disarming Reporting Options are set to always report disarming. Cancel alarm with user or WinLoad: An alarm is cancelled using the WinLoad software. Cancel Paramedic Alarm: A paramedic alarm is cancelled.
Special Alarm Report Codes
Sections [863] and [864] When the system generates an alarm due to one of the conditions listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of alarm. Section [863] Emergency Panic: Panic keys [1] and [3] have been pressed. Auxiliary Panic: Panic keys [4] and [6] have been pressed. Fire Panic: Panic keys [7] and [9] have been pressed. Recent Closing: Reports when an alarm is generated after arming the system within period defined by the Recent Close Delay. Section [864] Zone Shutdown: A zone communicates more than the programmed number of transmissions in a single armed period. Duress: A Duress access code is keyed in. Keypad Lockout: If a consecutive number of invalid codes are entered into a keypad, the control panel can be set to deny access from all keypads for a specified period. Paramedic Alarm: A parademic alarm is sent to the monitoring station.

Magellan / Spectra SP 43

System Trouble Report Codes
Section [865] to [869] When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble. Section [865] N/A AC Failure: The control panel has detected a loss of AC power. Transmission of this report code can be delayed. Battery Failure: Backup battery is disconnected or battery voltage is low. Auxiliary Supply: Auxiliary power supply has overloaded. Section [866] Bell Output Overload: Bell/siren output has overloaded. Bell Output Disconnected: Devices connected to the Bell Output have been disconnected. Timer Loss: The control panel has detected a loss in time or clock failure. Fire Loop Trouble: The control panel has detected a tamper trouble on a fire zone. Section [867] Fail To Communicate: The control panel has failed all attempts to communicate with the monitoring station. The report code will be transmitted upon the next successful attempt. RF Interference: Will report if the RF signal is being jammed. Module Lost: The control panel has failed to communicate with one or more modules (including keypads). Module Tamper: The anti-tamper switch of a module (including keypads) has been triggered. Section [868] Module AC Fail: The AC voltage of a module has dropped below recommended limits. Module Low/No Battery: The battery voltage of a module has dropped below recommended limits. Wireless Zone Low Battery: The battery voltage of a wireless transmitter has dropped below recommended limits. Wireless Zone Supervision Lost: The control panel has lost communication with a wireless zone. Section [869] Wireless PGM Supervision Lost: The control panel has lost communication with a wireless PGM. Wireless PGM Tamper: The anti-tamper switch of a wireless PGM has been triggered. N/A N/A

System Trouble Restore Report Codes
Sections [870] to [874] When the system restores one of the troubles listed in System Trouble Report Codes above, the control panel can send the appropriate report code to the monitoring station identifying the type of system trouble restore. If Telephone Line Monitoring is enabled, the control panel can also transmit a TLM Restore report code.
System Special Report Codes
Sections [875] to [876] When the system generates one of the instances listed below, the control panel can send the appropriate report code to the monitoring station identifying the type of system occurrence. Section [875] Cold Start: The control panel was completely shutdown (no battery, no AC) and then was re-started. Test Report: A test report has been generated automatically. WinLoad In: The control panel has commenced communication with WinLoad. WinLoad Out: The control panel has ended communication with WinLoad. Section [876] Installer In: Installer/Maintenance has entered the programming mode. Installer Out: Installer has exited the programming mode. Closing Delinquency: The control panel will send a Closing Delinquency report code if the system has not been armed within a programmed amount of days. N/A

Clear Reporting Codes

Section [966]: Clear Reporting Codes Option [1] OFF = Clear zone reporting codes Option [1] ON = Clear zone reporting codes (default)
44 Reference & Installation Manual
Option [2] OFF = Clear user reporting codes Option [2] ON = Clear user reporting codes (default) Option [3] OFF = Clear arm/disarm/alarm reporting codes Option [3] ON = Clear arm/disarm/alarm reporting codes (default) Option [4] OFF = Clear trouble reporting codes Option [4] ON = Clear trouble reporting codes (default) Enable all options you want to clear. The respective sets of reporting codes will be cleared after exiting the section.

Reset Reporting Codes

Section [967]: Reset Reporting Codes Option [1] OFF = Reset zone reporting codes Option [1] ON = Reset zone reporting codes (default) Option [2] OFF = Reset user reporting codes Option [2] ON = Reset user reporting codes (default) Option [3] OFF = Reset arm/disarm/alarm reporting codes Option [3] ON = Reset arm/disarm/alarm reporting codes (default) Option [4] OFF = Reset trouble reporting codes Option [4] ON = Reset trouble reporting codes (default) Enable all options you want to reset to default. The respective sets of reporting codes will be reset after exiting the section.
Monitoring Station Telephone Numbers
Section [815] = Phone#1, [816] = Phone#2, [817] = Backup Phone#, [818] = Pager #, [819] = Numeric Message Sent with Pager Reporting: Up to 32 digits The control panel can dial up to 2 different monitoring station telephone numbers. You can enter any digit from 0 to 9 and any special keys or functions (see Table 5 on page 45) up to a maximum of 32 digits. After the maximum dialing attempts (see Maximum Dialing Attempts on page 47) to one monitoring station telephone number have failed, the control panel will then dial the backup telephone number. If the Alternate Dial Option (see Alternate Dial Option on page 48) is enabled, the control panel will dial the programmed backup telephone number after every failed attempt. If no backup telephone number is programmed, the control panel will never report to the backup telephone number. Also see Delay Between Dialing Attempts on page 47. Table 5: Special Keys for Telephone Numbers Press [OFF] [BYP] [MEM] [TBL] [SLEEP] [ ] * # switch from pulse to tone dialing or vice versa 4-second pause deletes current digit inserts blank space Action or Value

12.27.1 TLM Fail Timer

Section [830] 016 to 255 x 2 seconds, Default = 32 seconds If TLM does not detect the existence of a telephone line for the duration of this period, the control panel will generate the condition(s) defined by the TLM options.

Magellan / Spectra SP 49

Pager Reporting Delay
Section [834]: Communication Timers 000 to 255 seconds, Default = 20 seconds When using the Pager Reporting Format, the control panel will wait for the Pager Delay period before transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the welcome message before sending data.
Pager Reporting Message Repetition
Section [835]: Communication Timers 000 to 255 times, Max. 10, Default = 3 When using the Pager Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged.

Personal Reporting Delay

Section [836]: Communication Timers 000 to 255 times, Max. 127, Default = 5 When using the Personal Reporting Format, the control panel will wait for the Personal Delay period before transmitting the report codes. This is to allow time for the system to provide a dial tone or to bypass the welcome message before sending data. This section applies to the Plug-in Voice Dialer when using a VDMP3.
Personal Reporting Message Repetition
Section [837]: Communication Timers 000 to 255 times, Max. 10, Default = 3 When using the Personal Reporting Format, the control panel will repeatedly send the report codes to the pager until the transmission has been acknowledged. This section applies to the Plug-in Voice Dialer when using a VDMP3.

Disable Reporting

Sections [800] Option [1] OFF = Dialer Activated (default) Option [1] ON = No Dialer With this option disabled (default), the control panel will continue to report events. With the option enabled, reporting is disabled.
50 Reference & Installation Manual
Part 13: Programmable Outputs
A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. The control panel includes two/four onboard PGMs. It can support up to a total of 16 PGMs. A Wireless PGM module can be assigned to any PGM. It will work in parallel with the Control Panel Output.

If enabled, the panel can wait for each of its assigned wireless transmitters to send a status signal within a specified time to confirm their presence and functionality. Option [4] OFF Option [4] ON = PGM Activation Mode Steady (default) = PGM Activation Mode Pulse
This option sets the PGM to be either steady (ON), or pulsed (ON/OFF) when it is activated.

Magellan / Spectra SP 51

Option [5] OFF Option [5] ON
= PGM Pulse once every 30 seconds disabled (default) = PGM Pulse once every 30 seconds enabled
When armed, the PGM will pulse once every 30 seconds. Option [6] OFF = PGM Pulse on any alarm disabled (default) Option [6] ON = PGM Pulse on any alarm enabled This option sets the PGMs to pulse on any alarm. Option [7] OFF Option [7] ON = PGM Pulse on any alarm Partition 1(default) = PGM Pulse on any alarm Partition 2
Program PGMs to pulse during an alarm for either partition. With this feature enabled, and in combination with the Follow Arm/ Stay Arm/Sleep Arm PGM type, the PGM will mimic the Arm LED.

PGM Programming

Sections [301] to [316] The programming of the PGMs is accomplished in two steps: 1. Assign the PGMs to the panel. 2. Program the PGMs. PGM Programming can be executed through the Installer Quick Menu in the programming guide. How Do I Assign PGMs to the Panel? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) 3) Enter the desired [SECTION NUMBER] (from sections [301] to [316]). 4) Enter the 6-digit [SERIAL NUMBER] of the PGM. How Do I Delete Assigned PGMs? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111) 3) Enter the desired [SECTION NUMBER] (from sections [301] to [316]). 4) Press the [0] key six times to clear the serial number.
Viewing the PGM Signal Strength
Sections [321] to [336] Once PGMs have been installed and assigned to the panel, the signal strength of each PGM can be verified in sections [321] to [336]. Sometimes moving the PGM or control panel by a small amount will greatly increase the signal reception. How Do I View a Wireless Transmitters Signal Strength? 1) Press the [ENTER] key. 2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (empty by default) 3) Enter the desired [SECTION NUMBER] (from sections [321] to [336]). 4) Press the transmitters anti-tamper switch or open the corresponding zone. 5) The keypad will illuminate numbers 1 to 10. Signal Strength Indicator 8 to 10 / 3 beeps = Best signal

Call Back WinLoad

Section [900]: Dialer Options Option [1] OFF = Call Back WinLoad Disabled (default) Option [1] ON = Call Back WinLoad Enabled For additional security, when a PC using the WinLoad software attempts to communicate with the control panel, the control panel can hang up and call the PC back in order to re-verify identification codes and re-establish communication. When the control panel hangs up, the WinLoad software automatically goes into Wait for Call mode, ready to answer when the control panel calls back. Please note that the PC Telephone Number must be programmed in section [915] in order to use the Call Back feature.

Connecting to WinLoad

Computer containing WinLoad software Standard DB-9 cable (9-pin serial cable) 306 Adapter/ CONV3USB Converter 4-pin connector cable Serial Connector
56 Reference & Installation Manual

Part 16: User Operation

16.1 Alarm Display
If an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory. These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live display mode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones LEDs will turn off, while the [MEM] key remains lit. Press the [MEM] key to illuminate the LEDs corresponding to the zones that were in alarm. The alarm memory will be erased when the next alarm occurs and after a valid code is entered or upon full-arming the system.

Trouble Display

Press the [TBL] key to view the Trouble Display. Please note that the keypad can be programmed to emit a beep every 5 seconds whenever a new trouble condition has occurred. Press the [TBL] key to stop the beeping. To view the sub-menu, press the corresponding key in the main menu. Main Menu Trouble [1] Wireless zone low battery [2] Power trouble Sub-Menu Trouble Menu [1] to [32] Zones in low battery [1] Low/No battery on the control panel [2] AC failure on control panel [3] Auxiliary overload on control panel [4] Wireless keypad AC failure [5] Wireless keypad battery failure [6] Wireless repeater AC failure [7] Wireless repeater battery failure [1] Bell disconnect on control panel [2] Bell overload on control panel [1] Telephone Line Monitoring on control panel [2] Fail to communicate on Monitoring Telephone 1 on control panel [3] Fail to communicate on Monitoring Telephone 2 on control panel [4] Fail to communicate on pager telephone on control panel [5] Fail to communicate on voice telephone on control panel [6] Fail to communicate with PC on control panel [1] to [32] Zones in tamper and zone wiring failure [1] MG-2WPGM [2] Keypad bus [5] Wireless keypad [1] to [32] Zones in fire loop trouble [1] to [32] Zones in supervision lost [STAY] RF interference trouble [1] MG-2WPGM [2] Keypad bus (Panel reset will not clear this trouble, clear it in section [955]) [5] Wireless keypad supervision failure [6] Wireless repeater supervision failure

[3] Bell trouble [4] Communication trouble
[5] Tamper and zone wiring failure [6] Module tamper trouble
[7] Fire loop trouble [8] Timer loss [9] Wireless zone supervision loss [0 (10)] or [10] Module supervision loss
[16] Keypad fault (MG32LED/MG32LRF only) [SLEEP] Keypad fault (MG10LEDV/H only)

Magellan / Spectra SP 57

Numerics
24 Hr. Burglary Zones... Hr. Buzzer.. Hr. Freeze Zones... Hr. Gas Zones.. Hr. Heat Zones... Hr. Hold-up Zones.. Hr. Water Zones.. 25 Bell Cut-Off Timer.. 41 Bell Output Connection... 11 Disconnected Report Code.. 44 Overload Report Code.. 44 Bell Squawk On Arm/Disarm With Keypad... 39 With Remote Control.. 39 Bypassable Zones... 26
AC Failure Report Code.. 44 AC Power... 3 Access Codes... 18 Length.. 18 Account... 47 Ademco Contact ID.. 46 Ademco Express... 46 Advanced Settings... 21 Advanced Technology Zone (ATZ) Connections. 13 alarm... 42 Alarm Display... 57 Alarm Options... 41 Alarm Report Code Transmission, Delay. 27 Alarm Types... 27 Alternate Dial Option.. 48 Answer WinLoad Software... 56 Answering Machine Override.. 55 Armed Report Delay... 48 Arming and Disarming Options.. 37 ATZ Wiring Options.. 28 ATZ Zone Doubling.. 28 Audible.... 42 Audible Trouble Warning Except AC Failure. 54 Audible Trouble Warning on AC Failure. 54 Auto Event Buffer Transmission.. 56 Auto Force Arming... 37 Auto Test Report... 48 Auto Zone Shutdown.. 26 Counter... 26 Report Code... 43 Auto-Arming Options... 39 Timer... 38 Timing.. 38 Auxiliary Panic Report Code.. 43 Auxiliary Power... 11 Auxiliary Supply Report Code.. 44
Call Back Feature.. 56 Call WinLoad Software.. 56 Cancel Auto-Arm Report Code.. 43 Charge Current... 53 Closing Delinquency... 49 Cold Start Report Code... 44 Configuring The LED Keypads.. 16 Connecting Bells or Sirens... 11 Fire Zones.. 14 PGMs... 11 Single Zone Inputs.. 12 Telephone Lines... 11 Counter, Auto Zone Shutdown.. 26
Data Display Mode... 16 Daylight Savings Time... 54 Delay... 40, 50 Before Alarm Report Code Transmission. 27 Between Dialing Attempts.. 47 Power Failure Report... 49 Delayed Fire Silent Zones.. 24 Delayed Fire Zones.. 24 Dial.... 48 Dialer settings... 43 Dialing Attempts.. 47 Dialing Method... 47 Disable Test Reporting.. 50 Disarmed Report Delay... 48 Display.... 55 Display Entry Delay.. 55 Display Exit Delay.. 55 Duress.... 19 Duress Report Code... 43
Backup Battery... 3 Battery Charge Current... 53 Battery Failure Report Code.. 44 Battery, Backup... 3 Beep On Exit Delay.. 39
Emergency Panic Report Code.. 43 Entry Delay 1 / Stay / Sleep Zones.. 23 Entry Delay 2 / Stay / Sleep Zones.. 23 Entry Delay on LCD keypad.. 55 Entry/Exit... 21 Entry/Exit with a Keypad.. 21 Entry/Exit with a Remote Control.. 21

Zone Definition Status...26 Zone Definitions...22 Zone Input 1 Becomes a 2-wire Smoke Input.28 Zone Options Delay Before Alarm Report Code Transmission..27 Force Zones...27 Zone Programming...22 Zone Restore Report Options..49 Zone Shutdown, Auto..26 Zone Timers...28

Magellan / Spectra SP 61

Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions.
Limitations of Alarm Systems
It must be understood that while your Paradox alarm system is highly advanced and secure, it does not offer any guaranteed protection against burglary, fire or other emergency (fire and emergency options are only available on certain Paradox models). This is due to a number of reasons, including by not limited to inadequate or improper installation/positioning, sensor limitations, battery performance, wireless signal interruption, inadequate maintenance or the potential for the system or telephone lines to be compromised or circumvented. As a result, Paradox does not represent that the alarm system will prevent personal injury or property damage, or in all cases provide adequate warning or protection. Your security system should therefore be considered as one of many tools available to reduce risk and/or damage of burglary, fire or other emergencies, such other tools include but are not limited to insurance coverage, fire prevention and extinguish devices, and sprinkler systems. We also strongly recommend that you regularly maintain your security systems and stay aware of new and improved Paradox products and developments.
Warning for Connections to Non-Traditional Telephony (e.g. VoIP)
Paradox alarm equipment was designed to work effectively around traditional telephone systems. For those customers who are using a Paradox alarm panel connected to a non-traditional telephone system, such as "Voice Over Internet Protocol" (VoIP) that converts the voice signal from your telephone to a digital signal traveling over the Internet, you should be aware that your alarm system may not function as effectively as with traditional telephone systems. For example, if your VoIP equipment has no battery back-up, during a power failure your system's ability to transmit signals to the central station may be compromised. Or, if your VoIP connection becomes disabled, your telephone line monitoring feature may also be compromised. Other concerns would include, without limitation, Internet connection failures which may be more frequent than regular telephone line outages. We therefore strongly recommend that you discuss these and other limitations involved with operating an alarm system on a VoIP or other non-traditional telephone system with your installation company. They should be able to offer or recommend measures to reduce the risks involved and give you a better understanding.