RZ_IB_Farbpistole_Deck.fh10 31.07.2003 14:27 Uhr Seite 4

C M Y CM MY CY CMY K

Spray Gun
Komperna Handelsgesellschaft mbH Burgstr. 21 D-44867 Bochum (Germany)

Probedruck

RZ_IB_Farbpistole_Klap.fh10 31.07.2003 14:42 Uhr Seite 4
Preparation of material to be sprayed

PFSPS 150 Spray Gun

Dear Customer, it is recommended to familiarise yourself with the functions of the spray gun before using it and to study the operating instructions carefully, including the safety information. The spray gun should only be used as described and for the specified applications.
Commercially available lacquers, paints and varnishes are usually adjusted for brushing and not for spraying. For a correct working result, the viscosity of the lacquers, paints and varnishes should be adjusted according to DIN guidelines (see table). The necessary dilution can be achieved using suitable thinner. 1.) Mix undiluted product well at 20C 2.) Add suitable thinner 3.) Check viscosity as described above -- see Fig. C --

PFSPS Technical Data

Nominal power : Delivery: Viscosity: Nominal pressure head: Tank capacity: Protection class: Test mark: 150 Watt 380 g/ min (water) max. 100 DIN-sec max. 100 bar 0,765 Liter CE, TV GS

Accessories

- 3x Spray nozzle 0,6+ 0,8 mm (1 x assembled) - 3x Pressure suction valve (1 x assembled) - 1x Spring - 1x Cleaning nozzle - 1x Nozzle extension - 1x Measuring cup
Never adjust synthetic paint with diluent for cellulose lacquers !
Material example Car paint Acrylic paint Synthetic paint Primer DIN guide values 16-20 DIN-sec 25-30 DIN-sec 25-30 DIN-sec 30-35 DIN-sec

Spraying

The surface to be sprayed must be clean, dry and free from grease. Observe the safety information 1.) Spray jet regulation -- see Fig. A --. The jet is correctly adjusted when no drops form and the spray is fine and regular. 2.) Do not switch the spray gun on/off over the spraying area, but start and end spraying about 10 cm outside the spraying area. 3.) Spray as shown in Fig. D. Move the spray gun parallel with the surface - do not move from side to side. Move the spray gun at a constant speed. Apply the material as thinly as possible. The paint coats need to dry before the next coat is applied crosswise -- see Fig. E --. 4.) Do not empty the tank completely as this will produce drips !
Noise and vibration measured according to EN 50144-1:1998, EN 50144-2-7:2000 The A-rated sound pressure level of the device is typically 93,9 dB(A). The sound power level can exceed 106,9 dB(A) during use. Hearing protectors should be worn! The hand vibration is typically lower than 2.5M/s2

PFSPS features

1. Regulating knob 4. Spray nozzle 7. Pressure suction valve 10. Pump piston 2. On/Off switch 5. Fixing screw 8. Aperture 3. Tank 6. Motor housing 9. Spring
Safety information relating to the use of the spray gun
Read the information in the enclosed General safety information booklet Inhaling the spray is dangerous to health Wear a protective mask ! When working in closed rooms, ensure good ventilation Explosion hazard ! No naked flame in the working area Do not smoke ! Do not spray any flammable or explosive liquids Never aim the spray jet at people or animals The spray gun must not be used in an environment where gases are present or can develop
Maintenance and cleaning General information
1.) 2.) 3.) 4.) Disconnect the mains plug, also when working on the gun and when the gun is not in use. Spray thinner or water through the spray gun after each use. Spray sewing machine oil through the spray gun after cleaning for protection against rust. Never immerse the spray gun in cleaning agent.
Maintenance and cleaning Special information
1.) 2.) 3.) 4.) 5.) 6.) Disconnect the mains plug, also when working on the gun and when the gun is not in use. Unscrew locking screw 5 -- see Fig. B --. Remove pump unit downwards. Unscrew nozzle 4, remove valve 7. Remove piston 10 and spring 9 from the spray gun. Clean the components 4, 7, 9, 10.

0,6 mm

0,8 mm
WORKING INFORMATION DIN-Sec / viscosity
The Parkside PFSPS 150 spray gun can be used for the application of up to maximum 100 DIN-sec. (viscosity). The viscosity can be determined with a simple measuring procedure using the supplied measuring beaker. 1.) Fill the measuring beaker full to the brim. 2.) Measure the efflux time in seconds. 3.) This time is termed DIN-seconds.
Environmental compatibility and material disposal
Paints, varnishes and lacquers are special waste and must be disposed of accordingly. Observe the local regulations. Follow the manufacturers directions. Environmentally harmful chemicals must be prevented from entering the soil, groundwater and lakes, rivers or canals. Spraying in the area of lakes, rivers or canals or surrounding areas (catchment area) is therefore forbidden. When purchasing paints, lacquers and varnishes, it must be ensured that these are environmentally compatible.