OPERATOR'S MANUAL

30cc String Trimmers and Brushcutter RY30000 Series
CS30 (RY30000, RY30000A, RY30021, RY30021A) SS30 (RY30002, RY30002A, RY30041, RY30041A)
BC30 (RY30004, RY30004A, RY30061, RY30061A)
Your new trimmer has been engineered and manufactured to Ryobis high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operators manual before
using this product. Thank you for buying a Ryobi trimmer.
SAVE THIS MANUAL FOR FUTURE REFERENCE

TABLE OF CONTENTS

Introduction...... 2 General Safety Rules..... 3 Specific Safety Rules..... 4 Symbols...... 5 - 6 Specifications..... 7 Unpacking..... 7 Features...... 8 - 9 Assembly..... 10 - 14 Operation..... 15 - 18 Maintenance..... 19 - 22 Troubleshooting..... 23 - 24 Warranty..... 25 - 26

INTRODUCTION

Trimming weeds and grass is an easy task using Ryobi Trimmers and Brushcutters. Safety, performance, and dependability have been given top priority in the design of this string trimmer making it easy to maintain and operate.

Page 2

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. Keep all parts of your body away from any moving part. To avoid hot surfaces, never operate the unit with the bottom of the engine above waist level. Do not touch area around the muffler or cylinder of the unit, these parts get hot from operation. Always stop the engine and remove the spark plug wire before making any adjustments or repairs except for carburetor adjustments. Inspect the unit before each use for loose fasteners, fuel leaks, etc. Replace any damaged parts before use. The string head or blade will rotate during carburetor adjustments. It has been reported that vibrations from hand-held tools may contribute to a condition called Raynauds Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. It is presently unknown what, if any, vibrations or extent of exposure may contribute to the condition. There are measures that can be taken by the operator to possibly reduce the effects of vibration: a) Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynauds Syndrome. b) After each period of operation, exercise to increase blood circulation. c) Take frequent work breaks. Limit the amount of exposure per day. d) Keep the tool well maintained, fasteners tightened and worn parts replaced. If you experience any of the symptoms of this condition, immediately discontinue use and see your physician about these symptoms. Mix and store fuel in a container approved for gasoline. Mix fuel outdoors where there are no sparks or flames. Wipe up any fuel spillage. Move 9 m (30 ft. ) away from refueling site before starting engine. Stop the engine and allow to cool before refueling or storing the unit. Allow the engine to cool; empty the fuel tank and secure the unit from moving before transporting in a vehicle.

READ ALL INSTRUCTIONS

For safe operation, read and understand all instructions before using this product. Follow all safety instructions. Failure to follow all safety instructions listed below, can result in serious personal injury. Do not allow children or untrained individuals to use this unit. Never start or run the engine in a closed or poorly ventilated area; breathing exhaust fumes can kill. Clear the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the cutting line or blade. Wear safety glasses or goggles that are marked to comply with ANSI Z87.1 standard when operating this product. Product users on United States Forest Service land, and in some states, must comply with fire prevention regulations. This product is equipped with a spark arrestor; however, other user requirements may apply. Check with your federal, state, or local authorities. Wear heavy, long pants, boots, and gloves. Do not wear loose fitting clothing, short pants, or go barefoot. Do not wear jewelry of any kind. Never operate this unit on the operator's left side. Secure long hair above shoulder level to prevent entanglement in moving parts. Keep all bystanders, children, and pets at least 15 m (50 ft.) away. Do not operate this unit when you are tired, ill, or under the influence of alcohol, drugs, or medication. Do not operate in poor lighting. Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance or exposure to hot surfaces.

Page 3

SPECIFIC SAFETY RULES
SPECIFIC SAFETY RULES FOR TRIMMER USE
Replace string head if cracked, chipped, or damaged in any way. Be sure the string head or blade is properly installed and securely fastened. Failure to do so can cause serious injury. Make sure all guards, straps, deflectors and handles are properly and securely attached. Use only the manufacturer's replacement string in the cutting head. Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury. Never operate unit without the grass deflector in place and in good condition. Maintain a firm grip on both handles while trimming. Keep string head below waist level. Never cut with the string head located over 76 cm (30 in.) or more above the ground. Replace any blade that has been damaged. Always make sure blade is installed correctly and securely fastened before each use. Failure to do so can cause serious injury. Use only the manufacturer's replacement TRI-ARC blade intended for use on this brushcutter. Do not use any other blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury. The TRI-ARC blade is suited for cutting thicker weeds or pulpy stalks only. Do not use for any other purpose. Never use the TRI-ARC blade to cut woody brush. Exercise extreme caution when using the blade with this unit. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly thrust the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut from the right to the left. In the event an unexpected object or woody stock is encountered, this could minimize the blade thrust reaction. Never cut any material over 13 mm (1/2 in.) diameter. Always wear the shoulder harness when using the brushcutter and adjust to a comfortable operating position. Maintain a firm grip on both handles while cutting with a blade. Keep the blade away from body and below waist level. Never use the brushcutter with the blade located 76 cm (30 in.) or more above the ground level.
SPECIFIC SAFETY RULES FOR BRUSHCUTTER AND BLADE USE
After engine stops, keep rotating blade in thicker weeds or pulpy stalks until it stops. Do not operate the brushcutter unless the brushcutter guard is firmly secured in place and in good condition. Use heavy gloves when operating the brushcutter and when installing or removing blades. Always stop the engine and remove the spark plug wire before attempting to remove any obstruction caught or jammed in the blade or before removing and installing the blade. Do not attempt to touch or stop the blade when it is rotating. A coasting blade can cause injury while it continues to spin after the engine is stopped or throttle trigger released. Maintain proper control until the blade has completely stopped rotating.

Page 4

SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning for safe operation of this product. SYMBOL NAME Safety Alert Symbol. Read the Operators Manual To reduce the risk of injury, user must read and understand operators manual before using this product. Wear eye protection which is marked to comply with ANSI Z87.1 as well as hearing protection when operating this equipment. Keep all bystanders at least 50 ft. (15 m) away. EXPLANATION Precautions that involve your safety.
Wear Eye and Hearing Protection

Keep Bystanders Away

50' 15m

Ricochet

Thrown objects can ricochet and result in personal injury or property damage.

No Blade

Do not install or use any type of blade on a product displaying this symbol.

Blade Thrust

Beware of blade thrust. Products authorized for blade use will display this symbol to warn of blade thrust.

Gasoline and Oil

Use unleaded gasoline intended for motor vehicle use with an octane rating of 87 ([R + M] / 2) or higher. This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil.

Page 5

The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. (Without Safety Alert Symbol) Indicates a situation that may result in property damage.
DANGER: WARNING: CAUTION: CAUTION:

SERVICE

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE DEALER for repair. When servicing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to operate this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing others who may use this product.
Observe all normal safety precautions related to avoid electrical shock.
The operation of any product can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87.1.

FRONT HANDLE LOCK WASHER WING NUT

BOLT FLAT WASHER Fig. 4

ATTACHING THE J BARRIER HANDLE BC30
See Figure 5. A barrier handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter. 1. Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator's left. 2. Insert the end of the handle between the clamps. 3. Align the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.) through the handle side. 4. Place short bolt (1/4-20 x 1 in.) through opposite side of clamp. Install flat washer, lock washers and hex nuts to hold the assembly in place. 5. After assembly is complete, adjust the position of the handle for best balance and comfort. 6. Tighten first the long bolt and then the short bolt.
BOLT 1/4-20 x 1 in. FRONT HANDLE

BOLT 1/4-20 x 1 1/2 in.

STRAP HANGER

FLAT WASHER LOCK WASHER

HEX NUT

Fig. 5

Page 11
ATTACHING THE GRASS DEFLECTOR

BOLT GRASS DEFLECTOR

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury. TO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30 See Figure 6. 1. Press the grass deflector onto the bottom of the curved shaft as shown. 2. Insert the hex head cap screw through the grass deflector and the bracket on the curved shaft. 3. Place the flat washer and lock washer on the hex head cap screw. 4. Place the wing nut on the hex head cap screw and tighten securely. TO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30 See Figure 7. 1. Remove the slotted hex head screw from the grass deflector. 2. Insert the tab on the mounting bracket in the slot on the grass deflector. 3. Align the screw hole in the mounting bracket with the screw hole in the grass deflector. 4. Insert the slotted hex head screw through the mounting bracket and into the grass deflector. 5. Tighten the screw securely.

BRACKET LOCK WASHER

FLAT WASHER

WING NUT

Fig. 6

HEX HEAD SCREW

STRAIGHT SHAFT GRASS DEFLECTOR SLOT
ATTACHING THE BRUSHCUTTER GUARD BC30
See Figure 8. The guard is shipped installed on these brushcutter models. Instructions have been included for reference when changing from string trimmer operation back to brushcutter operation. 1. With the string head removed, place the brushcutter guard on the gear head as shown. 2. Install the three screws from bottom through the guard and into the gear head. 3. Tighten the screws securely and torque to 40-50 in.lbs. minimum (finger right plus 1/4 turn).

GEAR HEAD

Fig. 7

BRUSHCUTTER GUARD

Fig. 8 Page 12
ATTACHING THE SHOULDER HARNESS BC30
See Figure 9. 1. Connect the latch on the shoulder harness to the strap hanger. 2. Adjust the strap to a comfortable position.
CONVERTING FROM BRUSHCUTTER TO STRING TRIMMER - BC30
To convert from the brushcutter to the string trimmer, remove the blade and brushcutter guard, attach the straight shaft grass deflector and install the string head. REMOVING THE TRI-ARC BLADE AND BRUSHCUTTER GUARD See Figures 10 and 11. 1. Align the slot in the flanged washer with the slot in the gear head. 2. Place the gear head locking tool through the slot in the flanged washer and gear head. 3. Remove the blade nut by turning it clockwise. 4. Remove the cupped washer and the blade 5. Remove the flanged washer from the gear head shaft and retain it for the string head installation. 6. Remove the three screws securing the brushcutter guard to gear head. 7. Remove the brushcutter guard. NOTE: Store the brushcutter parts together for later use. INSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD See Figures 10 and 12. 1. Install the grass deflector. Refer to To Attach the Straight Shaft Grass Deflector earlier in this manual. 2. Place the flanged washer on the gear head shaft. NOTE: The hollow side of the flanged washer should face the gear head. 2. Align the slot in the flanged washer with the slot in the gear head. 3. Place the gear head locking tool through the slot in the flanged washer and gear head. 4. Install the string head assembly onto the gear head shaft by turning counterclockwise. 6. Tighten the string head assembly securely.

SHOULDER HARNESS

Fig. 9
GEAR HEAD LOCKING TOOL Fig. 10 GEAR HEAD BRUSHCUTTER GUARD FLANGED WASHER
SLOT CUPPED WASHER BLADE NUT GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLY Fig. 11

LOOSEN Page 13

TIGHTEN Fig. 12
CONVERTING FROM STRING TRIMMER TO BRUSHCUTTER - BC30
To convert from the string trimmer to the brushcutter, remove the string head assembly and straight shaft grass deflector, attach the brushcutter guard and install the blade. REMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD See Figures 10 and 13. 1. Align the slot in the flanged washer with the slot in the gear head. 2. Place the gear head locking tool through the slot in the flanged washer and gear head. 3. Remove the string head assembly. 4. Remove the flanged washer and retain it for the blade installation. 5. Remove the screw securing the grass deflector. 6. Remove the grass deflector. NOTE: Store the string head parts together for later use. INSTALLING THE TRI-ARC BLADE AND BRUSHCUTTER GUARD See Figures 10 and 14. 1. Install the brushcutter guard. Refer to Attaching the Brushcutter Guard earlier in this manual. 2. Place the flanged washer over the gear head shaft with the hollow side toward the brushcutter guard. 3. Center the blade on the flanged washer, making sure the blade fits flat and the raised hub of the flanged washer goes through the hole in the blade. 4. Install the cupped washer with the raised center away from the blade. 5. Place the blade nut onto the gear head shaft. 6. Place the gear head locking tool through the slot in the flanged washer and gear head. 7. Install the blade nut by turning it counterclockwise (left handed threads). 8. Tighten the blade nut securely and torque to 120 in.lbs. minimum (finger tight plus 1/2 turn). GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLY

LOOSEN

TIGHTEN Fig. 13

FLANGED WASHER

SLOT CUPPED WASHER BRUSHCUTTER GUARD BLADE NUT

Fig. 14

Page 14

OPERATION

FUELING AND REFUELING THE TRIMMER
FUEL MIXTURE This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline. Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use. Mix a high quality 2-cycle engine oil at 2.6 oz. per gallon (US). Do not use automotive oil or 2-cycle outboard oil. DO NOT mix quantities larger than usable in a 30 day period. FUEL MIXTURE HIGH QUALITY 2-CYCLE ENGINE OIL GASOLINE OIL 1 gallon (US) 2.6 oz. 1 Liter 20 cc (20 ml)
To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Hold the trimmer with the right hand on the rear handle and the left hand on the front handle. Keep a firm grip with both hands while in operation. Trimmer should be held at a comfortable position with the rear handle about hip height. Always operate trimmer at full throttle. Cut tall grass from the top down. This will prevent grass from wrapping around the shaft housing and string head which may cause damage from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass. Prolonged cutting at partial throttle will result in oil dripping from the muffler.
FILLING TANK 1. Clean surface around fuel cap to prevent contamination. 2. Loosen fuel cap slowly. Rest the cap on a clean surface. 3. Carefully pour fuel into the tank. Avoid spillage. 4. Prior to replacing the fuel cap, clean and inspect the gasket. 5. Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use.
OPERATING THE CURVED SHAFT TRIMMER
Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. (9 m) from refueling site before starting engine. Do not smoke!

OPERATING THE TRIMMER

See Figure 15.
OPERATING THE STRAIGHT SHAFT TRIMMER
Always position the unit on the operator's right side. The use of the unit on the operator's left side will expose the user to hot surfaces and can result in possible burn injury.

Fig. 15

Page 15
TO ADVANCE THE CUTTING LINE String advance is controlled by tapping the string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap the spool retainer on ground to advance string. The string advances each time the spool retainer is tapped. Do not hold the spool retainer on the ground. NOTE: The line trimming cut-off blade on the grass deflector will cut the line to the correct length. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, stop the engine, and manually advance the string. TO ADVANCE THE CUTTING LINE MANUALLY Push the spool retainer down while pulling on string(s) to manually advance the string. CUTTING TIPS See Figures 16 and 17. Keep the trimmer tilted toward the area being cut; this is the best cutting area. The curved shaft trimmer cuts when passing the unit from right to left. The straight shaft trimmer cuts when passing the unit from left to right. This will avoid throwing debris at the operator. Avoid cutting in the dangerous area shown in Figures 16 and 17. Use the tip of string to do the cutting; do not force string head into uncut grass. Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, curbs, and wood may wear string rapidly. Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the string. GRASS DEFLECTOR LINE TRIMMING CUT-OFF BLADE See Figure 18. The trimmer is equipped with a line trimming cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance the string whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep the string long enough to advance properly. CURVED SHAFT TRIMMER DANGEROUS CUTTING AREA

DIRECTION OF ROTATION

BEST CUTTING AREA STRAIGHT SHAFT TRIMMER

Fig. 16

DANGEROUS CUTTING AREA

BEST CUTTING AREA

Fig. 17
STRAIGHT SHAFT TRIMMER LINE TRIMMING CUT-OFF BLADE
CURVED SHAFT TRIMMER LINE TRIMMING CUT-OFF BLADE Fig. 18

Page 16

OPERATING THE BRUSHCUTTER
See Figures 19 and 20. Hold the brushcutter with the right hand on the rear handle and the left hand on the J Barrier Handle. Keep a firm grip with both hands while in operation. Brushcutter should be held at a comfortable position with the trigger handle about hip height. Maintain your grip and balance on both feet. Position yourself so that you will not be drawn off balance by the kickback reaction of the cutting blade. Adjust the shoulder harness to position the brushcutter at a comfortable operating position and to assure that the shoulder harness will reduce the risk of operator contact with the blade.

TRI-ARC BLADE The TRI-ARC blade is suited only for thicker weeds and pulpy stalks. When the blade becomes dull, it can be turned over to extend the life of the blade. Do not sharpen the TRI-ARC blade. Use only TRI-ARC blade, part number AP04105, available at your local retailer. CUTTING TECHNIQUE - BLADE
Extreme care must be taken when using blades to ensure safe operation. Read the safety information for safe operation using the blade, refer to Specific Safety Rules for Brushcutter and Blade Use earlier in this manual. Always hold brushcutter on your right side with both hands when operating. Use a firm grip on both handles. Maintain your grip and balance on both feet. Position yourself so that you will not be drawn off balance by the kickback reaction of the cutting blade. Inspect and clear the area of any hidden objects such as glass, rocks, concrete, fencing, wire, wood, metal, etc. Never use blades near sidewalks, fencing, posts, buildings or other immovable objects. Never use a blade after hitting a hard object without first inspecting it for damage. Do not use if any damage is detected. The unit is used as a scythe, cutting from the right to the left in a broad sweeping action from side to side. Use only the TRI-ARC blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury. DIRECTION OF ROTATION
Fig. 19 BLADE THRUST Exercise extreme caution when using the blade with this unit. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly thrust the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut with the brushcutter, from the right to the left. In the event an unexpected object or woody stock is encountered, this practice could minimize the blade thrust reaction.
To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level.

CUTTING AREA

Fig. 20

Page 17

STARTING AND STOPPING
See Figures 21, 22, and 23. Trimmer should be on a flat, bare surface for starting. 1. Slowly press the primer bulb seven (7) times. 2. Set the choke lever to the FULL CHOKE position (A). 3. Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than eight (8) times. NOTE: Keep throttle trigger squeezed fully through STEP 6. 4. Set the choke lever to the HALF CHOKE position (B). 5. Pull the starter handle until the engine runs. Do not pull the starter handle more than six (6) times. 6. Allow the engine to run for 15 seconds, then set the choke lever to the RUN position (C).

PULL COVER TO OPEN Fig. 29

FILTER

SLOTS ON AIR FILTER BASE
REPLACING AND CLEANING AIR FILTER
See Figures 29 and 30. For proper performance and long life, keep air filter clean. 1 Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover. 2 Remove the filter, clean it in warm soapy water. Rinse and let dry completely. For best performance, replace annually. 3 Reinstall the filter. 4 Replace the air filter cover by inserting the tabs on the bottom of the cover into the slots on the air filter base; push the cover up until it latches securely in place.

TABS ON AIR FILTER COVER

Fig. 30

Page 21

FUEL CAP STORAGE (1 MONTH OR LONGER)
1. Drain all fuel from tank into a container approved for gasoline. Run engine until it stops. 2. Clean all foreign material from the trimmer. Store it in a well-ventilated place that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. 3. Abide by all ISO and local regulations for the safe storage and handling of gasoline. Excess fuel should be used up in other 2-cycle engine powered equipment.
A leaking fuel cap is a fire hazard and must be replaced immediately. The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine performance. If performance improves when the fuel cap is loosened, check valve may be faulty or filter clogged. Replace fuel cap if required.

SPARK PLUG

This engine uses a Champion RCJ-6Y with 0,63 mm (.025 in.) electrode gap. Use an exact replacement and replace annually.

Page 22

TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM Engine will not start: POSSIBLE CAUSE 1. No spark. SOLUTION 1. Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the starter rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug. 2. Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a servicing dealer. If primer bulb fills, engine may be flooded, proceed to next item. 3. Remove spark plug, turn trimmer so spark plug hole is aimed at the ground. Move choke lever to RUN and pull starter cord 10 to 15 times. This will clear excess fuel from engine. Clean and reinstall spark plug. Pull starter three times with choke lever at RUN. If engine does not start, move choke lever to CHOKE and repeat normal starting procedure. If engine still fails to start, repeat procedure with a new spark plug. 4. Contact a servicing dealer.

2. No fuel.

3. Engine is flooded.
4. Starter rope pulls harder now than when new. Engine starts but will not accelerate: Engine requires approximately three minutes to warm up.
Allow engine to completely warm up. If engine does not accelerate after three minutes, contact a servicing dealer. Contact a servicing dealer.
Engine starts but will only run at high speed at half choke: Engine does not reach full speed and emits excessive smoke:
Carburetor requires adjustment.
1. Check oil fuel mixture. 2. Air filter is dirty. 3. Spark arrestor screen is dirty.
1. Use fresh fuel and the correct 2-cycle oil mix. 2. Clean air filter. Refer to Replacing and Cleaning Air Filter earlier in this manual. 3. Contact a servicing dealer. Turn idle speed screw clockwise to increase idle speed. See Figure 31.
Engine starts, runs, and accelerates but will not idle:
Idle speed screw on carburetor needs adjustment.

Page 23

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM String will not advance when using the EZ Line tap advance system: POSSIBLE CAUSE 1. String is welded to itself. 2. Not enough string on spool. 3. String is worn too short. 4. String is tangled on spool. 5. Engine speed is too slow. Spool retainer hard to turn when using EZ Line tap advance system: Grass wraps around driveshaft housing and string head: Oil drips from muffler: Screw threads are dirty or damaged. SOLUTION 1. Lubricate with silicone spray. 2. Install more string. Refer to String Replacement earlier in this manual. 3. Pull strings while alternately pressing down on and releasing spool retainer. 4. Remove string from spool and rewind Refer to String Replacement earlier in this manual. 5. Advance string at full throttle. Clean threads and lubricate with grease - if no improvement, replace the spool retainer.
1. Cutting tall grass at ground level. 2. Operating trimmer at part throttle. 1. Operating trimmer at part throttle 2. Check oil/fuel mixture. 3. Air filter dirty.
1. Cut tall grass from the top down to prevent wrapping. 2. Operate trimmer at full throttle. 1. Operate trimmer at full throttle. 2. Use fresh fuel and the correct 2-cycle oil mix. 3. Clean per instruction in Maintenance Section.

IDLE SPEED SCREW

Fig. 31

Page 24

WARRANTY
THE FOLLOWING CARB STATEMENT ONLY APPLIES TO MODEL NUMBERS REQUIRED TO MEET (CARB) REQUIREMENTS. RYOBI TECHNOLOGIES INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Ryobi Technologies Inc. are pleased to explain the Emission Control System Warranty on your nonroad or small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state's stringent anti-smog standards. In other states, new 2000 and later model year nonroad engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regulations for small nonroad engines. The nonroad engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser. Ryobi Technologies Inc. must warrant the emission control system on your nonroad or small off-road engine for the period of time listed above provided there has been no abuse, neglect, or improper maintenance of your nonroad or small off-road engine. Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, the catalytic converter. Also included may be hoses, belts, and connectors and other emission related assemblies. Where a warrantable condition exists, Ryobi Technologies Inc. will repair your nonroad or small off-road engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor. MANUFACTURER'S WARRANTY COVERAGE: The 1995 and later small off road engines are warranted for two years in California. In other states, 1997 and later model year nonroad engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by Ryobi Technologies Inc. free of charge. OWNER'S WARRANTY RESPONSIBILITIES (a) As the nonroad or small off-road engine owner, you are responsible for the performance of required maintenance listed in your owner's manual. Ryobi Technologies Inc. recommends that you retain all receipts covering maintenance on your nonroad or small off-road engine, but Ryobi Technologies Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer. (b) As the nonroad or small off-road engine owner, you should be aware, however, that Ryobi Technologies Inc., may deny you warranty coverage if your nonroad or small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. (c) You are responsible for presenting your nonroad or small off-road engine to a Ryobi Technologies Inc., service dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact a Ryobi Technologies Inc., Customer Representative at 1-800-860-4050. COVERAGE: Ryobi Technologies Inc. warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small off-road engine will be designed, built and equipped, at the time of sale, to meet all applicable regulations. Ryobi Technologies Inc. also warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the nonroad or small off-road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Ryobi Technologies Inc. at no cost to the owner. Ryobi Technologies Inc. shall remedy warranty defects at any authorized Ryobi Technologies Inc. engine dealer or warranty station. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work determines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty. Ryobi Technologies Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty. The California Air Resources Board's Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA's regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.) These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter and Fuel Filter. MAINTENANCE REQUIREMENTS The owner is responsible for the performance of the required maintenance as defined by Ryobi Technologies Inc. in the operator's manual. LIMITATIONS The Emission Control Systems Warranty shall not cover any of the following: (a) repair of replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or replacements not conforming to Ryobi Technologies Inc. specifications that adversely affect performance and/or durability, and alterations or modifications not recommended or approved in writing by Ryobi Technologies Inc., and (b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement point. The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.

Page 25

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST Emissions Parts Inspect Before Clean Every Each Use 5 Hours Replace Every 25 Hours or Yearly Clean Every 25 Hours or Yearly
AIR FILTER ASSY INCLUDES: FILTER... X.. X SPARK SCREEN...... X CARBURETOR ASSY INCLUDES: HEAT DAM GASKETS FUEL TANK ASSY INCLUDES: FUEL LINES.. X FUEL CAP. X FUEL FILTER IGNITION ASSY INCLUDES: SPARK PLUG.... X ALL EMISSIONS - RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO THE PARTS FIRST SCHEDULED REPLACEMENT WHICH EVER COMES FIRST.

Page 26

Page 27
CS30 - RY30000, RY30000A, RY30021, RY30021A SS30 - RY30002, RY30002A, RY30041, RY30041A BC30 - RY30004, RY30004A, RY30061, RY30061A

SERVICE

Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi Authorized Service Center.

MODEL NO. AND SERIAL NO.

The model number of this tool will be found on a plate attached to the motor housing. Please record the model number and serial number in the space provided below.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: MODEL NUMBER SERIAL NUMBER

RYOBI TECHNOLOGIES INC.

1428 Pearman Dairy Road Post Office Box 1207 Anderson, SC 29625 Anderson, SC 29622 Phone 1-800-860-4050

983000-401

GardenProducts

www.texas-garden.com

Electric tillers. page 3 Hobby tillers..page 4-5 TX tillers..page 6-7 Futura tillers..page 8-9 Pro Trac tillers.. page 10-11 Lawn mowers.. page 12-15 Scarifiers and lawn edgers.. page 16-17 Lawn tractor accessories. page 17 Trimmer/Brushcutters. page 18-19 Leaf blowers.. page 20 Combi 650.. page 21 Pro / Handy sweepers.page 22 - 23 Log splitters.. page 24-26 Power saws and earth auger. page 27 Hedge trimmers. Page 28 Chain saws.. page 29 Tex Parts.. page 30
You are always welcome to contact us by mail, fax or phone. Phone: +99 Fax: +58 e-mail: export@texas.dk www.texas-garden.com
Dear TEXAS reader! Welcome to the newest catalogue of TEXAS garden products. This catalogue presents a wide range of products designed for use during spring, summer, autumn and winter. This means that no matter if you are an importer of Texas products, a dealer or if you are one of our many private or professional users of a Texas product, there is something to keep you busy all year round. TEXAS - Danish design and innovation Texas was founded in 1960 and is today 100% Danish owned. Our deep rotes in production and designing machines for the garden people are shown in our many new product designs that are created continously. Our product development division makes sure that we keep our status on the market as a proactive supplier that offer innovation and creative machine designs to our customers. Only such products carry our destintive Texas logo! TEXAS - total flexibility and low costs through own assembly Through our assembly line we handle big production series and manage coordination of productions and shipments within short time directly from factory - either in Texas branding or as personalised products in private brand. TEXAS - we guarantee a professional service When you work with Texas you are secured a professional after sales service that will guarantee you a safe investment in your machines. With more than 40.000 spare parts in stock and a full set of technical product documentation available on-line on www.texas-garden.com we ensure you the service you deserve. All our business partners work with Texas via our online service systems in a quick and smooth way where each order is processed from receipt till dispatch from our warehouse in minimum time. TEXAS - we supply to you any where, at any time The unique logistical system is a key factor to fast and cost efficient deliveries. We supply small shipments on a day-to-day basis from our central warehouse in Denmark. Most products are continously in stock for the season which means that the speed of deliveries through our distribution system is very fast. Should you need deliveries in container loads directly from our factory in the Far East this will be carried out in a quick and flexible way - at low cost. www.texas-garden.com Find more information of products, specifications, user manuals, pictures on our informative web site www.texas-garden.com. Here you will also find video presentations of products like our TX and Futura tillers and our sweepers. Use our web site as part of your marketing or simply as your own personal guide to find the information about Texas that you need. We hope that you will enjoy our catalogue!

Address:

Texas Andreas Petersen A/S Knullen 22 DK-5260 Odense S Denmark
Electric Mini Cultivators
With the electric Texas Mini Cultivators you get low weight, low noise and easy operation in one time. The cultivators are perfect in flowerbeds, between bushes and in general where the space is narrow and does not allow other machines to get in. You get a surprisingly big power output and consequently high work performance out of the machines.

5-in-1

Weeding out Cultivating and airing

FERTILIZER

Fertilizing

Planting

El Tex 750 Motor: 750 Watt / 230 V Working width: 28 cm Working depth: 20 cm Blades: Bolted (easy to replace) Weight: 9 kg.

Cat. no. 90062085

Edge cutting along with lawns or flower beds
How it works? The two knives are moving in opporsit directions which gives a steady and calm working proces. The result is incredible and a very effective way of a cultivating.
Jorden er luftig og fylder ca. det dobbelte

Kultiveret

Ikke kultiveret
Texas ES 300 Motor: 300 watt / 230V Working width: 15 cm Working depth: 10 cm Adjustable handle Handle: divisible Weight: 4,6 kg

Cat. no. 90063007

El Tex 1300 Motor: 1300 Watt / 230 V Working width: 28 cm Working depth: 20 cm Support wheels Weight: 15 kg.

(Needs rear console and 12 wheels)

Rake 80 cm

Cat. no. 91062500100

Weeder 65 cm

Cat. no. 91061500100

Wheels set 12

Cat. no. 91053000100
Wheel weight set kg each Iron wheels set 12

Cat. no. 91097000100

Cat. no. 91060600100

Rear console

Used when the accessory is rear mounted. (exept ridger)

Cat. no. 91059000100

Smart wheel support
Unique and smart support wheel system. Easy to operate with the foot. Quick conversion to transport mode.
The TX line - the choice for the demanding user.
The Texas TX tiller help you perform heavy garden tasks. The combination of low weight and large engine power makes the TX tiller an effective and easy-to-handle machine which is simple to use, yet strong in power. The rotor knives are made of hardened steel and detachable for maximum flexibility. The inside components are highly reliable for many hours of work - even in tough conditions. A wide range of accessories is available such as ridger, wheels, plough, how iron, snow blade and more.
User friendly transport wheel system The transport wheels can be activated by the foot thus making them very easy to operate. After transport the wheels are simply pushed backwards into cultivation position. Tool box The handle bar contains a small tool box for convenient storage of gloves, tools or other relevant material.
1 Ergonomic and adjustable handle. The handle is designed in the optimum size for the modern use and on the TX502 model the handle is multi adjustable. You can achieve the best working position for any type of job required. 2 Cultivation speed. The rotor speed is designed for best work output in most soil conditions. The speed is adapted to the weight of the tiller and ensures a high work output and leaves the soil well cultivated. 3 Rotor knives. Texas offers the best rotor knives on the market. There is lifetime guarantee against breakage! All knives are made of hardened steel, bolted and detachable for working widths form 30 to 85 cm.

Double gear handle The double handle function is an important safety feature that minimizes the risk of gear breakage.
High quality components inside The belts and gear components are vital for a tiller to function correctly. They are made of highest quality with reliable and precise dimensions giving the best and most reliable working output. TX501 TG Photo shown with extention rotors and side discs to be ordered separately. Engine: Texas Power Line TG510 4-stroke / 3.30kW / 168cc Tank capacity: 3.6 litres steel tank Transmission:1 forward + 1 reverse Rotor speed: 90-95 rpm at 3600 engine rpm Working width: 30-55-85 cm
(85cm achieved only with optional rotor knives)
Working depth: 33cm Detachable and botlted knives Handle: Adjustable all directions Weight: 58 kg.

Cat. no. 90050280

Texas Powerline engine - reliability and power The well known Texas Powerline engine is the preferred choice for many specialists over more than 5 years. With this engine you will experience reliability and high power output combined with a small spare part consumption.
TX501 B Engine: Briggs & Stratton 800 4-stroke/ 2.69kW / 205cc Tank capacity: 3.6 litres steel tank Transmission:1 forward + 1 reverse Rotor speed: 90-95 rpm at 3600 engine rpm Working width: 30-55-85 cm

Cat. no. 91056000100

(Needs rear console and iron wheels)
Working depth: 33cm Detachable and botlted knives Weight: 55 kg.

Cat. no. 90050140

Iron wheel set 12

Cat. no. 91060800100

Rotor knife set 30cm extention width

Cat. no. 91050700100

Side disc set

Cat. no. 91061000100

TX502 TG Engine: Texas Power Line TG510 4-stroke / 3.30kW / 168cc Tank capacity: 3.6 litres steel tank Transmission:1 forward + 1 reverse Rotor speed: 90-95 rpm at 3600 engine rpm Working width: 30-55-85 cm
Used when the accessory is rear mounted. Not ridger.

Cat. no. 91057000100

Weeder 60 cm

Cat. no. 91070000100

(Needs 12 wheels)

Lawn spiker 66 cm

Cat. no. 91051500100

(Needs rear console)

Cat. no. 90050180

Snow blade 75 cm

including attachement

Cat. no. 92000160100

(Needs front attachment plate and 12 wheels)
TX502 B Engine: Briggs & Stratton 800 4-stroke / 2.69kW / 205cc Tank capacity: 3.6 litres steel tank Transmission:1 forward + 1 reverse Rotor speed: 90-95 rpm at 3600 engine rpm Working width: 30-55-85 cm

Wheel weights set 12 - 10 kg each Front attachment plate

Cat. no. 90050240

Cat. no. 91058000100
Futura 6003 A multi machine with muscles
Texas introduces an upgraded version of our well known Futura series. With a rock solid construction, this versatile machine can be used as a powerful tiller as well as a strong ploughing machine that does the job for the demanding user. Easy change of speeds (no belts needed). The universal adapter ensures a large range of accessories such as 16 wheels, heavy duty iron wheels, turning ploug, trailer with seat etc. The number of work purposes are endless if you are an owner of a Texas Futura machine. 3 engine options available: Robin Subaru EX 17, B&S Vanguard series and Texas Powerline TG650
See video on www.texas-garden.com
Danish design and development
Futura 6003 R Engine: Robin Subaru EX17 4-stroke / 2.9 kW / 169 cc Tank size: 3.6 litres Transmission: 2 forward+1 reverse intergrated gear in box Rotor rotation speed: 1. gear for accessories 47 RPM 1. gear for accessories 65 RPM Standard 3 knife rotor set 36, 64, 85 cm Working depth: 33 cm Detachable and bolted knives Universal rear mounting plate Support wheels fully adjustable and foot operated Basic weight without weight blocks: 62kg

Cat. no. 90145525100

Support Wheel Foot operated support wheels. Easy and quick usable system which transforms the machine from working mode till transport mode. The wheels have ball bearings. Gear box 2 speed forward and 1 speed reverse. Adjust the speed for any pur ose you need and p depending on the accessory you work with. No risk of belt overloading and no need of exchanging belts when speed is changed.
Ajustable handle Multi adjustable handle can be moved in all directions. A solid metal lock secures the handle in the desired position even during very demanding work. High quality components inside The belts and gear components are vital for a tiller to function correctly. They are made of highest quality with reliable and precise dimensions giving the best and most reliable working output.
Ridger for Futura Cat. no. 91060500100

Plough 6

Cat. no. 91093000100
Iron wheels set 16 Cat. no. 91065700100
Side disc set Cat. no. 91065600100
Futura 6003 TG As Futura 6003 R but with Power Line TG650 4-stroke / 4.0 kW / 196 cc

Cat. no. 90145570100

6 turning plough

91052100100

Trailer with seat and brake

Cat. no. 91200160100

Weeder 60 cm Cat. no. 91070000100

Rake 80 cm Cat. no. 91062500100
Potatoe plough Cat. no. 91061200100
Futura 6003B B&S 6,5 As Futura 6003 R but with B&S Vanguard 4-stroke / 205cc

Cat. no. 90145546100

Snow blade 75 cm including attachment
(Needs front attachment plate and 16 wheels)
Wheels set 16 Cat. no. 91065500100
Wheel weights set 21,5kg each Front attachment plate Basis front weight 12 kg Extra front weight 12 kg
Cat. no. 91098000100 Cat. no. 91065800100 Cat. no. 91090000100 (Needs front attachment plate) Cat. no. 91090500100
Engine: Choose between 3 engine options:
TG650 Power Line engine at high quality and low costs. B&S Vangaurd well known brand and classic engine. Robin Subaru EX17 engine constructed for 3000 hours of use. Strong gear box with integrated gear shift (no belts are needed for this task) that ensures maximum strength even for heavy garden work.
Rear adapter fits most accessories available. Easy to use, no tools needed and made in solid metal. Transport wheels with ball beari ngs and foot operated support bracket that allows for quick conversion to transport mode and vice visa. This system is unique for the Futura and makes it very easy to transport the machine despite the high weight of the machine. Adjustable handle allows the correct working position for all tasks. Can be side adjusted when ploughing or cultivating to avoid walking directly on the trail. Rotor knives made in hardened steel and bolted for easy exchange should a breakage occur. Standard working width of 85 cm can be reduced to 30 cm by disassembling the number of rotor sets. Ergonomic cluch handle for easy engagement of gear box.
Texas Pro Trac 2-wheeled tractor - versatile machines with incredible power
The Texas Pro Trac series are universal two-wheeled tractors that cover the needs of a professional user. The models range from Pro Trac 500 up to Pro Trac 900 available with both gasoline and diesel engines. Handling is simple and straight forward despite the power and size of the machines. Large amount of accessories available. The Pro Trac can be converted to a sweeper simply by removing the rear tiller and then attach the sweeper unit to the quick clutch without the use of tools.

Easy transfer

Pro Trac 555R Engine: Texas Power Line TG 550B 4-stroke / 3.30 kW / 163 cc Starter: Recoil Transmission (rearmounted accessories): 3 forward, 2 reverse (frontmounted accessories): 2 forward, 2 reverse Wheel size: 3.50x8 Quick clutch Weight: 65 kg.

Cat. no. 55520870

Pro Trac 500R Engine: Texas Power Line TG 550 4-stroke / 3.10 kW / 163 cc Starter: Recoil Transmission (rearmounted accessories): 1 forward, 1 reverse (frontmounted accessories): 1 forward, 1 reverse Wheel size: 4.00x8 Weight: 51 kg.

Cat. no. 42020870

ACCESSORIES Pro Trac 500
Collection box Mounted with sweeper Cat. no. 93300200100
Pro Trac 900DE Engine: Texas Power Line TD 900E diesel with electric start / 6.62 kW / 406 cc Transmission: (rearmounted accessories): 4 forward, 3 reverse (frontmounted accessories): 3 forward, 3 reverse Wheel size: 5.00x10 Quick clutch Weight: 125 kg.

Cat. no. 90041260

Rotary tiller, 50 cm Needs 4.00 x 8.

Cat. no. 978511

Sweeper 80 cm Cat. no. 93300080100
Cutting bar 96 cm Cat. no. 9L2411
Pro Trac 700D Engine: Texas Power Line TD 600 deisel / 4.41 kW 296 cc Starter: Recoil Transmission (rearmounted accessories): 3 forward, 2 reverse (frontmounted accessories):2 forward, 2 reverse Wheel size: 5.00x10 Quick clutch Weight: 115 kg.

Cat. no. 70020960

ACCESSORIES Pro Trac 555
Rotary tiller, 37 - 58 cm Needs 4.00 x 8.

Cat. no. 978911

Sweeper 80 cm Cat. no. 93300180100
Cutting bar 117 cm Cat. no. 9L2811
Snow blade 100 cm Cat. no. 9E6411
Snow thrower 60 cm Cat. no. 9E6922

Easy Transfer

EASY TRANSFER
The Pro Tracs are easily converted in to a professional Sweeper machine. See page 22-23
ACCESSORIES Pro Trac 700 - 900
Rotary tiller Needs 4.00 x 8. Cat. no. 984611 (Pro Trac 900 - 37-68 cm) Cat. no. 984511 (Pro Trac 700 - 37-58 cm) Sweeper 80 - 100 cm

Cat. no. 93500080100

(Pro Trac 700 and 900 -80 cm) (Pro Trac cm)
Single plough Needs attachement frame

Cat. no. 93500100100

Cat. no. 943122
Turning plough Needs attachement frame

Cat. no. 943222

Ridger Needs attachement frame

Cat. no. 944122

Rake 75cm
Rotor cutter 75cm Needs front weight

Cat. no. 93500500100

Cat. no. 9L6411
Cutting bar 117cm Cat. no. 9L6911
Engine: Strong and reliable gasoline or diesel engines available from 163 cc up 1 to 406 cc. 2 Gear box: The gear box is of very high quality and guarantee you a reliable working platform. The gear box components are of high quality materials which are used in the assembly proces. The shift between the forward and reverse gear is easy and quickly made. 3 Handle bar: Handle bar with anti vibration increases the user comfort during long working days. Further more the handle can be turned 180 degrees depending on which accessories that are used. A plastic cover on top of the handle bar protects all wires and other sensitive parts and gives a nice design of the machine. 4 Gear: Differential gear is available on the 900 model which means that the machine can be used even on slippery surfaces with better traction. At the same time the wheels can turn in oppersit direction which makes it easier to change direction of the machine when working. 5 Quick clutch: Exchange accessories easily and without the use of tools. Fits all accessories for Pro Trac and Pro Sweep series.

Snow blade 125cm Cat. no. 9E6511

Snow thrower 70cm

Cat. no. 9E9622
Wheels set Cat. no. 900112 (4.00 x 8) Cat. no. 900412 (5.00 x 10) Light device complete ONLY 900DE

Cat. no. 93500350100

Front weight Attachment frame Pulling bar Counter part for quick clutch Iron Wheels - only 700
Cat. no. 9G4812 Cat. no. 945322 Cat. no. 9F4212 Cat. no. 954812 Cat. no. 920312
Texas Black Edition - new high end series of lawn mowers
The new black line from Texas, is the result of the latest development, and now offers more features and better specifications normally found on competitive lawn mower in this class. They are all fitted with some of the strongest engines in the market, with electric start as an option. Besides this, comfort grip with integrated toolbox, bottle/can holder and throttle control, big rear wheels, XL size height adjustment grip and 4-in-1 function is standard on all the black lawn mowers.

Collection bag

Ideal for most types of gardens, where the grass is cut regularly. The grass is collected into the big 60 ltr. collection bag and leaves the lawn in a beautiful condition with no trace of grass pieces. The collection bag can also be used in the autumn to vacuum the lawn for leafs and small branches.

Rear discharge

Suitable for places, where the grass is not cut so often and where it is therefore long. A collection bag would quickly be full and should be emptied many times. With a rear discharged lawn mower, you will get the work done faster and easier.

Mulching

Mulching is easy and gives a nice result. With the mulching plug fitted into the lawn mower, the grass is cut into very small pieces, which will disappear down into the lawn and works as a natural fertilizer. Mulching however, requires a regular lawn mowing, 1-2 times per week, where the grass is dry, in order to get the best result.

Side discharge

With side discharge you can cut longer grass, straws because it is easier for the lawn mower to get rid of the grass this way. It is a good solution for places, where the grass is long and not cut so often. Side discharge also has the advantage that the grass is being spread out on the lawn instead of being left clumping behind the lawn mower.

Comfort grip

Electric start
Engine: Self propelled Electric start Cutting system Working width Collection bag Deck Bearings Height adjustment Weight Cat. no.
Texas Black Edition XT 50 TR/W
TG675 (200 cc) Self propelled No 4incm 60 ltr. Steel Ball bearings Central 7 pos. 25-75 mm 36 kg 90066037
Texas Black Edition XT 50 TR/WE
TG675 (200 cc) Self propelled Yes 4incm 60 ltr. Steel Ball bearings Central 7 pos. 25-75 mm 36 kg 90066038

Texas Black Edition XTB 50 TR/WD
B&S DOV 750 (161 cc)* Self propelled Ready Start** 4incm 60 ltr. Steel Ball bearings Central 7 pos. 25-75 mm 36 kg 90066045
*The DOV 750 Series engine delivers breakthrough performance driven by technology that makes a difference you can see, feel and hear. The patented Direct Overhead Valve (DOV) engine delivers more torque, improved sound quality, and less noise and vibration than competitive engines in the same class. ** No primer, no choker.
Rain cover for lawn mower
Texas lawn mowers - value for money
The yellow line of Texas lawn mowers, are fitted either with the reliable 139 cc engine or the stronger 173 cc engine. The mowers are delivered with 46 cm or 50 cm cutting width, with comfortable soft grip, central height adjustment and ball bearings in the self propelled versions. A mulching plug is included with all collector models, to offer a 3-in-1 function. The yellow line offers strong lawn mowers with good features to a very competitive price. In addition to the gasoline line, 2 electric models are offered. One basic model for very small areas, and a bigger one with nice features as big rear wheels, powerful motor, central height adjustment and a new innovative design.
Engine: Self propelled Cutting system Working width Collection ba Deck Bearings Height adjustment Weight Cat. no.

Texas SPD 50 TR/W

TG575 (173 cc) Self propelled 4incm 60 ltr. Steel Ball bearings Central 7 pos. 25-75 mm 36 kg 90066028

Texas SP 50 TR/W

TG475 (139 cc) Self propelled 3incm 60 ltr. Steel Ball bearings Central 7 pos. 25-75 mm 34 kg 90066027
Spinner 40 H Working width: 40 cm Deck material/Wheels: Steel Height adjustment: 15-32 mm Weight: 8.5 kg Texas SP 46 TR
TG475 (139 cc) Self propelled 3incm 60 ltr. Steel Ball bearings Central 5 pos. 25-70 mm 31 kg 90066023 Central 5 pos. 25-70 mm 31 kg pos. 25-55 mm 26 kg 90066002 3incm 60 ltr. Steel Steel Sidedischarge 50 cm

Texas SP 46

TG475 (139 cc)

Texas MT510

Cat. no. 90062010

Electric Mowers

Texas XT1400 Motor: 1400 watt Working width: 37 cm Collection bag: 40 l. Deck: Plastic Height adjustment: Individual 3 pos. 25-55 mm Weight: 12 kg

Cat. no. 90066031

Texas 32EL Motor: 1000 watt Working width: 32 cm Collection bag: 26 l. Deck: Plastic Height adjustment: Central 5 pos. 30-70 mm Weight: 8,5 kg

Loading capacity: 300 Kg Loading size: 154x95x35 cm

Cat. no. 90053030

Collection box for grass and moss 96 cm

Capacity: 300 litres

Cat. no. 90053031
Small trailer can be tiped
Loading capacity: 150 Kg Loading size: 97x76x30 cm

Cat. no. 90053034

Scarifier 96 cm

Cat. no. 90053033

Gravel Spreader

Cat. no. 699025

Texas Brush cutters and trimmers
Texas has developed a product range of cost effective and strong brush cutters and trimmers in a reliable quality. The range goes from 26 cc up to 43cc and engines are 2-stroke or 4-stroke with high power rate. The brush cutters are developed in a unique Danish design, which gives a different and very attractive line of brush cutters. The brush cutters have low vibration and offers high level or ergonomic with comfortable carrying harness and ergonomic adjustable handles. A range of nylon trimmer lines and cutting blades is available. Further more a general range of accessories is available in our Tex Part packaging. (see page 30)
Advantages with a Lithium battery
Always ready for use almost no self discharge up to 50 percent lower weight and better effect than the traditional battery. It makes the machine lighter and more manageable. Charger 80 percent at half the normal charging time it gives only short breaks by working. The battery does not have to be discharged before new charging Lithium batteries are environmental friendly
Texas trimmer ET18 Li Battery: 18 volt Lithium 1.3 Ah Capacity: 25 - 35 min Charging time: 3-5 hours Cutting width: 23 cm Weight: 2.5 kg

Cat. no. 90063057

2-in-1
Texas Trimmer GTX300 Engine: 2-stroke Euro 2 / 30cc Recoil start Carburettor: Membran Trimmer Head: tapn go 2.0 mm Cutting width: 40 cm D-handle Curved shaft Weight: 5.1 kg Lawn edger

Cat. no. 90062035

ET 1000 Motor: 900 watt / 230 volt Cutting width: 38 cm Handle: 2-handle w. softgrip Cutting line diameter: 2 mm Weight: 5 kg

Cat. no. ET1000

Texas GTX260 As GTX300 but with 26 cc engine

Cat. no. 90062017

See page 30
Texas Brushcutter BC335-4 Engine: 4-stroke / 33.5cc Tank capacity: 0.65 ltr Cutting width: 42 cm w. line Trimmerhead: Tapn go 2.4mm 3-tooth cutting blade Cutting width: 25 cm w. blade V-handle Straight Shaft Incl. professionel harness Weight: 6.9kg

Cat. no. 90062038

Centrifuge spreader CS2500 Capacity: 25 ltr Max spreading width: 2 m Adjustable dosing Big pneumatic wheels Weight: 10 kg.

Cat. no. 90052014

THE INNOVATIVE COMBI MACHINE FROM TEXAS
Quick clutch system. makes exchange of accessories both simple and fast. Heavy duty construction with focus on simplicity and reliability Integrated gear shift (no belts required) for quick speed regulation. Big wheels for rough terrain
Texas Combi 650 Engine options: Texas Power Line TG650B 4-stroke / 4.0 kW / 196 cc Robin Subaru EX17 4-stroke / 2.9 kW / 169 cc Wheel size: 4.80x8 Direct transmission Speed: 3 forward + 1 reverse 1.Gear forward: 1.2 km/h 2.Gear forward: 2.2 km/h 3. Gear forward:3.2 km/h Gear reverse: 2.0 km/h
Cat. no. 90068002 (TG) Cat. no. 90068004 (Robin)

Choose accessory

Sweeper Working width: 80 cm Brush diameter: 45 cm Brush rotation speed: 260 rpm 3 adjustable sweeper positions

Cat. no. 90068010

Snow blade: Working width: 80 cm 3 adjustable working positions Reinforced blade edge Replaceable blade edge

Cat. no. 90068012

Snow thrower Working width: 66 cm Rotation speed: 115 rpm Adjustable snow chute 2-stage function

Cat. no. 90068011

Quick change in
Press the foot bracket down to release the accessory from the quick clutch

30 seconds 3

Tilt the machine down, push it under the accessory and press it up to fix it to the quick clutch.
Pull the machine back, and the accessory will slide off
Texas Sweepers all year cleaning machines
Texas Sweepers are unique designed cleaning machines for use at both summer and winter time. All machines are highly ergonomically designed and offer simplicity in use with high effectiveness in the work carried out. Use the machines for cleaning of leafs, sand and dirt around houses, blocks, parking spaces etc. Due to the strong construction of the brushes the Handy Sweep and Pro Sweep series are also ideal for snow cleaning.
Pro Sweep 900DE - 100 cm Engine: Texas Power Line TD 900E diesel with electric start / 6.62 kW / 406 cc Transmission (frontmounted acc.): 3 forward, 3 reverse (rearmounted acc.): 4 forward, 3 reverse Wheel size: 5.00x10 Quick clutch 3 adjustable sweeper positions Weight: 225 kg.

Cat. no. 90190060100

Diesel engine with electric start for professional use

See on page 10-11

Accessories
Pro Sweep 700D - 80 cm Engine: Texas Power Line TD 600 deisel / 4.41 kW 296 cc Starter: Recoil Transmission (frontmounted acc.): 2 forward, 2 reverse (rearmounted acc.): 3 forward, 2 reverse Wheel size: 5.00x10 Quick clutch 3 adjustable sweeper positions Weight: 206 kg.

Cat. no. 90170060100

Pro Sweep 500 R Engine: Texas Power Line TG 550 4-stroke / 3.10 kW / 163 cc Transmission: 1 forward & 1 reverse Working width: 80 cm Brush diamater: 450 mm 3 adjustable sweeper positions Weight: 99 kg.

Cat. no. 90052005

Cross splitter head for Power Split 600

Cat. no. 90052008

Texas log splitters and log saws
A smaller range for the hobby segment is also available. Both 5 and 6 tons versions are strong and arsy to handle and are available with support stands for optimum working positions. Log saws are available in two versions. these machines are ideal for utting logs in the right dimensions before splitting with the logsplitter.
Easy operation Power Split 600H and 520H is equiped with 2 handels for easy and safe operation
Power Split 600H incl. support stand Motor: 2200 watt / 230 volt Capacity: 6 tons Working length: 52 cm 2-hand operation Strong support legs Weight: 52,5 kg

Cat. no. 90052081

Power Split 520H Motor: 1500 Watt / 230 volt Capacity: 5 tons Working length: 52 cm Horizontal working position 2 hand operation Weight: 50,5 kg

Cat. no. 90052096

5 tons capacity
Steel table for Power Split 520 H

Cat. no. 90052095

Max cutting width 210 mm
With Texas Power Saw 3000 you can quickly handle the hard work sawing wood. With a motor of 3000 Watt it can saw lengths up to 1,5 m with maximum diameter of 210 mm. The electric motor is furthermore equipped with a motor brake, which automatically turns off the motor at overload. Power Saw 3000 Motor: 3000 watt / 380 volt Blade: 600 mm Cutting diameter: 30-210mm Weight: 99 kg

Cat. no. 90052083

Power Saw 2201 Motor: 2200 Watt / 230 volt Cutting diameter: 125 mm Blade: 400 mm Weight: 51 kg

Cat. no. 90052000

Max cutting width 125 mm
Earth auger NEG 52 Motor: 52 cc 2-stroke Drilling depth: 70 cm Ergonomic handle Extention bar can be adapted Excl. drills Weight: 10.5 kg

Cat. no. NEG52

100 mm auger

Cat. no. 55720040

150 mm auger

Cat. no. 55720170

200 mm auger

Cat. no. 55720350

Extention bar 40 cm

Cat. no. 55750360

Texas chain saws and hedge trimmers
Everyone with garden and hedge need a hedge trimmer, and why not choose a hedge trimmer which has all the qualities which will help you to do the cutting. Texas presents a range of hedge trimmers and the user can choose models with either an electric or gasoline engine, or a battery-powered model. The Electric hedge trimmers have the advantages that they are easy to maintain, economic in operation and they weigh less than the gasoline models. With Texas gasoline hedge trimmers you are free and flexible without any cables.

Mr. Texas

Andreas Petersen realised his dream about becoming independent and getting his own company. What was more natural than to name the company TEXAS? Not only because this was the nickname Andreas Petersen received when working in the forests but also because everything from over there was very popular in this particular period. But also especially due to constant product developNot alone due to the strong products, and wide product range, large range of accessories and a high quality after sales service.

Selling tillers

ment in close dtialogue with the customers and users.read the full Texas story on www.texas.dk !

The Texas history.

The year is 1960 The Texas Year
The company Texas is founded in 1960 in Odense, Denmark. This is where the beginning of a business success takes place - but how did it all start up?
Andreas Petersen now participated in several fairs, which gave him the option to show the product and the interest was enormous. Consequently he started developing his own tiller for the Danish market and in January 1966 Andreas Petersens first Danish manufactured tiller was a reality.
Development of the company Texas
In the following years the company experienced an enormous growth. Stiga, the Swedish lawn mower manufacturer, caught interest in Andreas Petersen and his garden machine. This was the beginning of a true export adventure. During the following 10 years 60% of the production of the company was exported to more than 25 countries. Later on also many other partners in Europe helped founding the basis of Texas as an international company. Through the years Texas has succeeded in maintaining its market position and stay as one of the top suppliers and manufacturers within total solutions for the Garden and outdoor industry.
Here follows some history.
Andreas Petersen, a fresh and youthful son of a farmer from the Southern part of Denmark, had in the 1950es the wish to see something of the big wide world. He wished to go to Texas in the USA. It was particularly the forestry, Andreas Petersen was interested in, and in the USA he got acquainted with a tool which within a couple of years should revolutionize the forestry in Denmark: The chain saw.
Sales possibilities in Denmark
After getting back to Denmark Andreas Petersen was convinced about the sales possibilities in the product for the Danish forests and forest workers. He quickly discovered an enormous interest in the products in