Reviews & Opinions
Independent and trusted. Read before buy Partner P 33!

Partner P 33

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Partner P 33, size: 1.2 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Partner P 33About Partner P 33
Here you can find all about Partner P 33 like manual and other informations. For example: review.

Partner P 33 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Partner P 33 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Partner P 33 photo ]

Video review

Resident Evil 5 HD Professional Chapter 5 3 Monarch Room & Battle Continues P33

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 3. Page 1 of 1. Average Rating:
notyet 12:08am on Tuesday, May 18th, 2010 
An improvement for an excellent laptop I have been using an HP Elitebook 8530w for several months. HP Elitebook 8530w notebook workstation HP EliteBook Mobile Workstation 8530w - Core 2 Extreme X9100 / 3.
OverFlow 3:15am on Friday, April 2nd, 2010 
Fast and sturdy machine This is a very fast and sturdy machine with a nice design. It comes with Windows XP Pro SP2 installed.
oldchow 6:20pm on Monday, March 29th, 2010 
This is a WorkHorse This laptop has met and exceeded al my expectations I have been using one everday for well over 2 years.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

ELECTROLUX OUTDOOR PRODUCTS

953900457

Type/Prefix/nd

PARTNER

Number of Pages 1 of 4

Factory:

IIQ - Valmadrera
Product Group: OP 93 Petrol Portable Sub Group 9430
Publication Number: EIPL2005_VP0502021 Publication Date: 21/02/05

doc1

INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. MANUEL DINSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant dutiliser cet appareil, veuillez lire atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour rfrence ultrieure. BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Gerts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, da Sie alle Anweisungen verstanden haben und gut aufbewahren. MANUAL DE INSTRUCCIONES INFORMACIN IMPORTANTE: Lea atentamente las instrucciones y asegrese de entenderlas antes de utilizar esta aparato. Conserve las instrucciones para la referencia en el futuro.
545167620 Rev. 1 9/20/07 BRW
IDENTIFICATION (WHAT IS WHAT?)
Chain Adjustment Tool (Bar Tool) Front Hand Guard Front Handle Starter Rope Idle Speed Screw Chain Muffler ON/STOP Switch Primer Bulb

Bar Oil Fill Cap

Starter Housing
Fuel Mix Fill Cap Bumper Spike
Bar Guard Cylinder Cover Throttle Lockout Rear Handle

Adjusting Screw

Chain Direction of Travel
Throttle Choke/ Trigger Fast Idle Chain Brake Lever

Chain Catcher

Chain Brake Nuts

Guide Bar

Bar Sprocket Hole
IDENTIFICATION OF SYMBOLS

WARNING!

This chain saw can be dangerous! Careless or improper use can cause serious or even fatal injury. Read and understand the instruction manual before using the chain saw.
Always wear appropriate ear protection, eye protection and head protection.

Sound power level

Always use two hands when operating the chain saw.
WARNING! Contacting the guide bar tip with any object should be avoided; tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious injury. 2

Starting Reminder

Move ON/STOP switch to the ON position. Pull the starter rope sharply 5 times with your right hand.
Slowly press primer bulb 6 times.
Push the choke/fast idle lever in to the HALF CHOKE position.
Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).
Pull the starter rope sharply with your right hand until the engine starts.

SAFETY RULES

WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. Because a chain saw is a high-speed woodcutting tool, special safety precautions must be observed to reduce the risk of accidents. Careless or improper use of this tool can cause serious injury.

PLAN AHEAD

S Read this manual carefully until you completely understand and can follow all safety rules, precautions, and operating instructions before attempting to use the unit. S Restrict the use of your saw to adult users who understand and can follow safety rules, precautions, and operating instructions found in this manual. Safety Hat Hearing Protection Eye Protection Snug Heavy Duty Fitting Gloves Clothing S Always use approved hearing protection. Regular users should have hearing checked regularly as chain saw noise can damage hearing. Long-term exposure to noise can result in permanent hearing impairment. S Keep all parts of your body away from the chain when the engine is running. S Keep children, bystanders, and animals a minimum of 10 Meters away from the work area. Do not allow other people or animals to be near the chain saw when starting or operating the chain saw. S Do not handle or operate a chain saw when you are fatigued, ill, or upset, or if you have taken alcohol, drugs, or medication. You must be in good physical condition and mentally alert. Chain saw work is strenuous. If you have any condition that might be aggravated by strenuous work, check with your doctor before operating a chain saw. S Carefully plan your sawing operation in advance. Do not start cutting until you have a clear work area, secure footing, and, if you are felling trees, a planned retreat path.

WARNING: Never use a chain saw with defective safety equipment. Safety equipment must be inspected and maintained. If your chain saw does not pass inspection, take the saw to your nearest service dealer for repair. S Chain brake. Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake. For additional information, see OPERATING YOUR UNIT section. S Throttle trigger lock- out. Check that the throttle trigger can not be operated until the throttle lock-out is pressed. S Chain catcher. Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw. S Vibration damping system. Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit. S ON/STOP switch. Start the engine and make sure the engine stops when you move the ON/STOP switch to the STOP position.
MAINTAIN YOUR SAW IN GOOD WORKING ORDER
S Have all chain saw service performed by a qualified service dealer with the exception of the items listed in the maintenance section of this manual. For example, if improper tools are used to remove or hold the flywheel when servicing the clutch, structural damage to the flywheel can occur and cause the flywheel to burst. S Make certain the saw chain stops moving when the throttle trigger is released. For correction, refer to CARBURETOR ADJUSTMENTS. S Never modify your saw in any way. Use only attachments supplied or specifically recommended by the manufacturer. S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fasteners securely tightened. S Use only Partner accessories and replacement parts as recommended.

WARNING:

HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or while operating the saw. S Eliminate all sources of sparks or flame in the areas where fuel is mixed or poured. There should be no smoking, open flames, or work that could cause sparks. Allow engine to cool before refueling. S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fueling site before starting engine.
S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. S Store the unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

Avoid obstructions

Clear the working area

KICKBACK

WARNING: Avoid kickback which can result in serious injury. Kickback is the backward, upward or sudden forward motion of the guide bar occurring when the saw chain near the upper tip of the guide bar contacts any object such as a log or branch, or when the wood closes in and pinches the saw chain in the cut. Contacting a foreign object in the wood can also result in loss of chain saw control. S Rotational Kickback can occur when the moving chain contacts an object at the upper tip of the guide bar. This contact can cause the chain to dig into the object, which stops the chain for an instant. The result is a lightning fast, reverse reaction which kicks the guide bar up and back toward the operator. S Pinch-Kickback can occur when the the wood closes in and pinches the moving saw chain in the cut along the top of the guide bar and the saw chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation. The saw is driven straight back toward the operator. S Pull-In can occur when the moving chain contacts a foreign object in the wood in the cut along the bottom of the guide bar and the saw chain is suddenly stopped. This sudden stopping pulls the saw forward and away from the operator and could easily cause the operator to lose control of the saw. Avoid Pinch- Kickback: S Be extremely aware of situations or obstructions that can cause material to pinch the top of or otherwise stop the chain. S Do not cut more than one log at a time. S Do not twist the saw as the bar is withdrawn from an undercut when bucking. Avoid Pull- In: S Always begin cutting with the engine at full speed and the saw housing against wood. S Use wedges made of plastic or wood. Never use metal to hold the cut open. Kickback Path

REDUCE THE CHANCE OF KICKBACK
S Recognize that kickback can happen. With a basic understanding of kickback, you can reduce the element of surprise which contributes to accidents. S Never let the moving chain contact any object at the tip of the guide bar. S Keep the working area free from obstructions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting through a particular log or branch. S Keep your saw chain sharp and properly tensioned. A loose or dull chain can increase the chance of kickback occurring. Follow manufacturers chain sharpening and maintenance instructions. Check tension at regular intervals with the engine stopped, never with the engine running. Make sure the bar clamp nuts are securely tightened after tensioning the chain. S Begin and continue cutting at full speed. If the chain is moving at a slower speed, there is greater chance of kickback occurring. S Cut one log at a time. S Use extreme caution when re-entering a previous cut. S Do not attempt cuts starting with the tip of the bar (plunge cuts). S Watch for shifting logs or other forces that could close a cut and pinch or fall into chain. S Use the Reduced-Kickback Guide Bar and Low-Kickback Chain specified for your saw.

MAINTAIN CONTROL

Stand to the left of the saw
Never reverse hand positions

Elbow locked

Thumb on underside of handlebar
S Keep a good, firm grip on the saw with both hands when the engine is running and dont let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encircling and your left thumb under the front handlebar. Keep your right hand completely around the rear handle whether your are right handed or left handed. Keep your left arm straight with the elbow locked. S Position your left hand on the front handlebar so it is in a straight line with your right hand on the rear handle when making bucking cuts. Never reverse right and left hand positions for any type of cutting. S Stand with your weight evenly balanced on both feet. S Stand slightly to the left side of the saw to keep your body from being in a direct line with the cutting chain. S Do not overreach. You could be drawn or thrown off balance and lose control of the saw. S Do not cut above shoulder height. It is difficult to maintain control of saw above shoulder height.
S Low-Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Low-Kickback Chain Contoured Depth Gauge Elongated Guard Link Deflects Kickback Force And Allows Wood To Gradually Ride Into Cutter S Handguard, designed to reduce the chance of your left hand contacting the chain if your hand slips off the front handlebar. S Position of front and rear handlebars, designed with distance between handles and in-line with each other. The spread and in-line position of the hands provided by this design work together to give balance and resistance in controlling the pivot of the saw back toward the operator if kickback occurs.

KICKBACK SAFETY FEATURES

WARNING: The following features are included on your saw to help reduce the hazard of kickback; however, such features will not totally eliminate this dangerous reaction. As a chain saw user, do not rely only on safety devices. You must follow all safety precautions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury. S Reduced-Kickback Guide Bar, designed with a small radius tip which reduces the size of the kickback danger zone on the bar tip. A Reduced-Kickback Guide Bar has been demonstrated to significantly reduce the number and seriousness of kickbacks.
Reduced Kickback Symmetrical Guide Bar

Small Radius Tip

WARNING: DO NOT RELY UPON ANY OF THE DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Reduced-kickback guide bars and low-kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kickback chain and bar as original equipment. Repairs on a chain brake should be made by an authorized servicing dealer. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. S Tip contact in some cases may cause a lightning fast reverse REACTION, kicking the guide bar up and back toward the operator. S Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back toward the operator. S Either of these reactions may cause you to lose control of the saw which could result in serious injury. Do not rely exclusively upon the safety devices built into your saw.

Symmetrical Guide Bar

Large Radius Tip

ASSEMBLY

Protective gloves (not provided) should be worn during assembly.
ATTACHING THE BUMPER SPIKE
The bumper spike may be used as a pivot when making a cut. 1. Loosen and remove the chain brake nuts and the chain brake from the saw. 2. Attach the bumper spike with the two screws as illustrated.
ATTACHING THE BAR & CHAIN
(If not already attached)

Cutters

Depth Gauge
WARNING: Recheck each assembly step if the saw is received assembled. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving! 1. Loosen and remove the chain brake nuts and the chain brake from the saw. 2. Remove the plastic shipping spacer (if present).

Adjusting Screw - 1/4 Turn -
WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury. WARNING: Muffler is very hot during and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.
S Lift up the tip of the bar and securely tighten the chain brake nuts with the bar tool. S Recheck chain tension.

OPERATING YOUR UNIT

BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubrication. Lubrication is provided by the automatic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar. Only use Bar and Chain Oil for bar and chain lubrication. Oil Cap Fuel mix cap
tem of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front handle as far as possible. The chain brake must be disengaged before cutting with the saw.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. A 40:1 ratio is obtained by mixing 0,125 liter of oil with 5 liters of unleaded gasoline. DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel sys-
WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CARBURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns. To stop the engine, move the ON/STOP switch to the STOP position. To start the engine, hold the saw firmly on the ground as illustrated below. Make sure the chain is free to turn without contacting any object. Use only 15 --- 18 of rope per pull. Hold saw firmly while pulling starter rope.

IMPORTANT POINTS TO REMEMBER
When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly. For cold weather starting, start the unit at full choke; allow the engine to warm up before squeezing the throttle trigger. NOTE: Do not cut material with the choke/fast idle lever at the FULL CHOKE position.
STARTING A COLD ENGINE (or a warm engine after running out of fuel) NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically. ON/STOP SWITCH (SIDE VIEW) ON STOP 1. Move ON/STOP switch to the ON position. 2. Slowly press primer bulb 6 times. 3. Pull out choke/fast idle to the full extent (to the FULL CHOKE position). 4. Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step. NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step. 5. Push the choke/fast idle lever in to the HALF CHOKE position. CHOKE/FAST IDLE LEVER (SIDE VIEW)
Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE.
WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0,02 (0,5 mm) thick. Repairs on a chain brake should be made by an authorized service dealer. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. S This saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs. S The inertia activated chain brake is activated if the front hand guard is pushed forward, either manually or by centrifugal force. S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible. S When cutting with the saw, the chain brake must be disengaged. Disengaged Engaged
Choke/ fast idle lever OFF
Braking function control CAUTION: The chain brake must be
checked several times daily. The engine must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the engine running. Place the saw on firm ground. Grip the rear handle with your right hand and the front handle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

6. Pull the starter rope sharply with your right hand until the engine starts. 7. Allow the engine to run for approximately 30 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1. Move ON/STOP switch to the ON position. 2. Slowly press the primer bulb 6 times. 3. Pull the choke/fast idle lever out to the HALF CHOKE position. 4. Pull the starter rope sharply with your right hand until the engine starts. 5. Squeeze and release throttle trigger to allow engine to return to idle speed.
Inertia activating function control
DIFFICULT STARTING (or starting a flooded engine)
The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.
WARNING: When performing the following procedure, the engine must be turned off. Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14 (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS
S Check chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section. S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. S The bumper spike may be used as a pivot when making a cut. S Stop the saw if the chain strikes a foreign object. Inspect the saw and repair parts as necessary. S Keep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and increase the possibility of kickback. S Practice cutting a few small logs using the following techniques to get the feel of using your saw before you begin a major sawing operation. S Squeeze the throttle trigger and allow the engine to reach full speed before cutting. S Begin cutting with the saw frame against the log. S Keep the engine at full speed the entire time you are cutting. S Allow the chain to cut for you. Exert only light downward pressure. S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, unnecessary wear can occur. S To avoid losing control when cut is complete, do not put pressure on saw at end of cut. S Stop the engine before setting the saw down. Remove dirt, stones, loose bark, nails, staples, and wire from the tree where cuts are to be made. Plan a clear retreat path

S Watch out for springpoles. Use extreme caution when cutting small size limbs. Slender material may catch the saw chain and be whipped toward you or pull you off balance. S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released. S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them.
S Start at base of the felled tree and work toward the top, cutting branches and limbs. Remove small limbs with one cut. S Keep the tree between you and the chain as much as possible. S Remove larger, supporting branches with the cutting techniques described in BUCKING WITHOUT A SUPPORT. S Always use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job. S Make your fist cut 1/3 of the way through the bottom of the limb. S Next make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch collar from the trunk of the tree.

Second cut Third cut

LIMBING
S Always limb a tree after it is cut down. Only then can limbing be done safely and properly. S Leave the larger limbs underneath the felled tree to support the tree as you work.

Collar

First cut Pruning technique

SERVICE AND ADJUSTMENTS

Disconnect the spark plug before performing maintenance, except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer.
AIR FILTER CAUTION: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evaporative emissions.

Cleaning the air filter:

MAINTENANCE SCHEDULE Check: Fuel mixture level. Before each use Bar lubrication. Before each use Chain tension. Before each use Chain sharpness. Before each use For damaged parts. Before each use For loose caps. Before each use For loose fasteners. Before each use For loose parts. Before each use Inspect and Clean: Bar. Before each use Complete saw. After each use Air filter. Every 5 hours* Chain brake. Every 5 hours* Spark arresting screen and muffler. Every 25 hours* Replace spark plug. Yearly Replace fuel filter. Yearly * Hours of Operation
A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt and sawdust from falling into the carburetor chamber when the cover is removed. 2. Remove the parts as illustrated below. 3. Wash the filter in soap and water. Rinse in clean cool water. Air dry completely before reinstalling. 4. Add a few drops of oil to the filter; squeeze filter to distribute oil. 5. Reinstall parts. Air Filter Cylinder Cover Screws

Cylinder Cover

BAR MAINTENANCE
If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole. To maintain guide bar: S Move ON/STOP switch to the STOP position. S Loosen and remove chain brake nuts and chain brake. Remove bar and chain from saw. S Clean the oil holes and bar groove after each 5 hours of operation. Remove Sawdust From Guide Bar Groove

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENTS

WARNING: The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Chain moves at idle. See IDLE SPEED-T adjusting procedure. S Saw will not idle. See IDLE SPEED- ad-T justing procedure.

Idle Speed---T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T. S Turn idle speed screw (T) clockwise to increase engine speed. S Turn idle speed screw (T) counterclockwise to decrease engine speed.
Oil Holes S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file. S When rail top is uneven, use a flat file to restore square edges and sides. File Rail Edges and Sides Square Worn Groove Correct Groove Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

STORAGE

SPARK PLUG
The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and nonadjustable. 1. Loosen 3 screws on cylinder cover. 2. Remove the cylinder cover. 3. Pull off the spark plug boot. 4. Remove spark plug from cylinder and discard. 5. Replace with Champion RCJ-7Y spark plug and tighten securely with a 19 mm socket wrench. Spark plug gap should be 0,5 mm. 6. Reinstall the spark plug boot. 7. Reinstall the cylinder cover and 3 screws. Tighten securely. Cylinder Screws Cover Spark Plug Boot

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children. S Before storing, drain all fuel from the unit. Start engine and allow to run until it stops. S Clean the unit before storing. Pay particular attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces. S Do not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc. S Store in a dry area out of the reach of children. S Ensure the machine is cleaned and that a complete service is carried out before longterm storage. S The guide bar and chain must always be covered with a scabbard when the machine is being transported or in storage in order to prevent accident contact with the sharp chain. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

Spark Plug

CAUTION: It is important to prevent
gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Al-
cohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

TROUBLE

Engine will not start or will run only a few seconds after starting.
1. Ignition switch off. 2. Engine flooded. 3. Fuel tank empty. 4. Spark plug not firing. 5. Fuel not reaching carburetor. 1. Idle speed requires adjustment. 2. Carburetor requires adjustment. 1. 2. 3. 4. Air filter dirty. Spark plug fouled. Chain brake engaged. Carburetor requires adjustment. 1. Too much oil mixed with gasoline. 1. Idle speed requires adjustment. 2. Clutch requires repair.

REMEDY

1. Move ignition switch to ON. 2. See Difficult Starting in Operation Section. 3. Fill tank with correct fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. 1. See Carburetor Adjustment in the Service and Adjustments Section. 2. Contact an authorized service dealer. 1. 2. 3. 4. Clean or replace air filter. Clean or replace plug and regap. Disengage chain brake. Contact an authorized service dealer.

Engine will not idle properly. Engine will not accelerate, lacks power, or dies under a load. Engine smokes excessively. Chain moves at idle speed.
1. Empty fuel tank and refill with correct fuel mixture. 1. See Carburetor Adjustment in the Service and Adjustments Section. 2. Contact an authorized service dealer.
DECLARATION OF CONFORMITY
EC Declaration of Conformity (Only applies to Europe) We, Husqvarna Outdoor Products Italia, S.p.A., Valmadrera, Italy. Tel: +39-0341-203211, declare that the chain saw models Partner P33XT, P351XT, P4-18XT and P4-20XT CSI---AV from serial numbers 2007-151(N or D) 00001 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCILS DIRECTIVES: of 22 June 1998 relating to machinery 98/37/EC, annex IIA; of 3 May 1989 relating to electromagnetic compatibility 89/336/EEC, and applicable supplements; and of 8 May 2000 relating to the noise emissions in the environment in accordance with Annex V of 2000/14/EC. The measured sound power is 110 dB(A), the guaranteed sound power is 118 dB(A) and the net power is 1,1 kW, 1,2 kW or 1,3 kW. The following standards have been applied: ISO 11681- 1:2004, EN/ISO 12100- 1:2003, EN/ISO 12100- 2:2003, and CISPR 12:2001. Notified body, 0404 the Swedish Machinery Testing Institute, Fyrisborgsgatan 3 S-Uppsala, Sweden, has carried out EC type approval. The certificate(s) is numbered: 404/07/1193. The supplied Chain Saw conforms with the sample that underwent the EC type approval. 07- -31 -05Michael S. Bounds, Director Product Safety and Standards Handheld Consumer Products

TECHNICAL DATA SHEET

P33XT Engine P351XT P4-18XT 4-20XT Cylinder volume, cmStroke, mm 32 Idle speed, rpm 3000 Recommended max. speed, unloaded, rpm 13000 Power, kW 1,1 1,2 1,3 Ignition system Manufacturer Type of ignition system Spark plug Electrode gap, mm Fuel and lubrication system Manufacturer Carburetor type Fuel capacity, litre Oil pump capacity at 8500 rpm, ml/min Oil capacity, litre Type of oil pump Weight Without bar and chain, kg Length Inches Phelon CD Champion 0,5 Walbro WT-662 0,38 4- 8 0,2 Automatic 4,7 P33XT/P351XT Noise levels P4-18XT/P4-20XT Equivalent (see note 1) noise pressure level at operators ear, measured according to relevant international standards, dB(A) 96,3 Equivalent (see note 1) noise power level, measured according to relevant international standards, dB(A) 110 Vibration levels (see note 2) Front handle, m/s2 Rear handle, m/s2 Chain/bar Standard bar length, in/cm Recommended bar lengths, in/cm Usable cutting length, in/cm Chain speed at maximum power, m/sec Pitch, inches Thickness of drive link, mm No. of teeth on drive sprocket

2,4 3,6 14/35 14/35 13,5/0,375 1,3 6
BAR CHAIN Pitch Max Inches Tip Radius 0,375 7T Oregon 91VJ 0,375 7T Oregon 91VG
Note 1: Equivalent noise level is, according to ISO 22868, calculated as the time-weighted energy total for noise levels under various working conditions with the following time distribution, 1/3 idle, 1/3 full load, 1/3 full speed. Note 2: Equivalent vibration level is, according to ISO 22867, calculated as the time-weighted energy total for vibration levels under various working conditions with the following time distribution: 1/3 idle, 1/3 full load, 1/3 full speed.
in/cm :dl 91VJ 91VG 0,375 0,375 0,050/1,3 0,050/1,3 5/32 / 4,0 5/32 / 4,0 0,025/0,65 0,025/0,65 14/35:52 14/35:52
ADDRESS: Husqvarna Outdoor Products Italia S.p.A.
Via Como 72 Valmadrera, Lecco ITALY I-23868

 

Tags

Hyundai I30 SG-DV1660LC A6Y12f2b-E DCR-TRV18E PSR-640 VGN-FJ270-B Lapc-1 EW1079F DV-525 DCR-DVD810 NP-R530-js05ES 2 00 RRM320PU AD-44 CM148 Handheld W958C 5 5 570B-TFT Diplomacy RX-V496RDS Doro BM48 553ELX GR-642AP LAC-M1501 Aqxxf 129 795MB Plus GXT800 Photo PN42A400c2D CE1071 DCR-TRV19 MX4LR 3232C Scan Dual ZZR1400 ABS DP392G PSR-185-PSR-77 BV9455 Client Vpointhd RE-21CC30RX SA-AK22 MS8188E Magicolor 5440 SPH-A900 ES250PW Yamaha MD4 Cyber 3 LE32A465c1W Aficio 615C UNO RTS HT30744 DCR-HC46 Flash DCR-HC35E SM-6100SA Cherokee 455 FC383 Nizo 6080 1200 4V AWF1373S DC-FX1 LG-95Z Recorder Manager ALL-IN-wonder X800 Review Dmcfx66 Fisio 825 Stitch Watch A414 LV880 TI-5630 Digitv HD Bizhub C10P DSC-HX1 Turbo Jamo S60 WF-T752A SLV-E285VC MSV-01 20-keyl Cardio CW Wixe13 Montana 2000 S3600I DVD-H40A Ddlt21 30518 Ascona TX-SR303E 150D 1TB Roland E-36 DMC-300SC BV8965B EZ-J24 604 Wifi XSU-00350B DV438AGR 7965G

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101