ILLUSTRATED PARTS LIST

MODEL NUMBER SB270 PRODUCT NUMBER 00-06 MFG. ID. NUMBER 96191000612
430428 Rev. 1 10.14.09 SR

REPAIR PARTS

SNOW THROWER - MODEL NO. SB270 (96191000612), PRODUCT NO. 00-06
AUGER HOUSING / IMPELLER ASSEMBLY

01.07.026-C

2 (EXPLODED)
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 2

KEY NO. 37

PART NO. 41-42 71-18 89-42 71-17 53-18 40-19 21-40 54-80 04-78 04-42 79-16 31-42 71-42 71-90 06-18 03-19 41-40 77-42 73-42 73-40 77-40 77-17 46-40 77-40 77-18 92-40 77-17 46-42 71-78 36-17 46-17 46-40 77-40 77-40 77-42 73-19 20-90
DESCRIPTION IMPELLER GEARBOX ASSEMBLY BEARING IMPELLER PULLEY DISCHARGE BASE CORNER BRACKET CLEAN OUT TOOL TOOL CLIP NUT 1/4-20 SCREW 1/4-20 X.625 NUT 5/16-18 SCREW 5/16-18 X.625 IMPELLER HUB IMPELLER SLEEVE NUT 3/8-16 CARRIAGE BOLT SCREW 13-16 X.625 PLUG GEARBOX COVER RH GASKET SEAL BEARING THRUST WASHER 1.00 WORM GEAR AUGER SHAFT SQUARE KEY BEARING THRUST WASHER IMPELLER SHAFT ROLL PIN THRUST WASHER THRUST BEARING BEARING O-RING SCREW 5/16-18 X.750 GEARBOX COVER LH SHEAR BOLT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 3

3 (5x) 4 (5x) 2

01.07.002-A

KEY NO. 3 4

PART NO. 52-40 77-27 05-15 53-77
DESCRIPTION AUGER HOUSING 27 SCRAPER BAR CARRIAGE BOLT 5/1618 X.625 NUT 5/1618

01.07.018-A

KEY NO. 1 2

PART NO. 11-42 11-23

DESCRIPTION AUGER 27 LH AUGER 27 RH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 4

3 01.11.001-A 1

PART NO. 40-18 40-27 05-75 11-53
DESCRIPTION SKID PLATE LH SKID PLATE RH CARRIAGE BOLT 5/1618 X.75 NUT 5/1618

3 01.07.024-B

KEY NO. 3
PART NO. 04-41 19-17 95-82
DESCRIPTION AUGER BEARING BEARING PLUG SCREW 5/1618 X 1.00
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 5
CONTROL PANEL / DISCHARGE CHUTE
KEY NO. 7 *8 *9 *10 *11 *14 PART NO. 00-18 45-42 06-42 03-41 42-12 84-50 10-17 98-19 17-25 05-75 11-18 45-42 06-42 06-72 DESCRIPTION CHUTE WELDMENT DEFLECTOR WELDMENT 6 DEFLECTOR CONTROL ASSEMBLY DEFLECTOR SEAL KNOB BLACK 1 POP RIVET SCREW 10-24 X.625 SHOULDER SCREW NUT 1/4-20 CARRIAGE BOLT 5/16-18 X.50 NUT 5/16-18 DEFLECTOR SPRING (SERVICE PART) DEFLECTOR CONTROL HEAD (SERVICE PART) DEFLECTOR CONTROL CABLE

*11 *10

01.09.002-D
NOTE: 1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT. 2. ITEMS 13 AND 14 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 6

KEY NO. *3 *4 *5 *6 *7

PART NO. 82-50 10-42 06-40 59-42 06-42 82-42 83-10
DESCRIPTION LEVER/CABLE ROTATOR ASSEMBLY SCREW 10-24 X.625 ROTATOR HEAD ROTATOR PIVOT BRACKET PULLEY PIVOT CABLE ASSEMBLY ADJUSTABLE CABLE ASSEMBLY HEAT SHIELD

01.09.010-B

NOTES: 1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
KEY NO. PART NO. 12-04 10-24

01.15.009-A

DESCRIPTION STEER CABLE SCREW 1024 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 7

HANDLES

KEY NO. 4
PART NO. 11-42 11-78 05-75 11-53
DESCRIPTION LOOP HANDLE LH LOOP HANDLE RH SCREW 5/1618 X 1.50 NUT 5/1618

01.08.004-B

01.08.007-B

KEY NO. 5 6

PART NO. 62-41 45-17 88-16 96-06 04-42 18-14
DESCRIPTION INTERLOCK SPRING INTERLOCK CAM TORSION SPRING RETAINER SCREW 1/420 X.625 INTERLOCK STOP
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 8

01.08.002-F

KEY NO. PART NO. 55-42 88-42 88-42 90-42 90-41 26-42 16-16 96-06 04-41 42-41 42-17 88-13 13-12 06-18 DESCRIPTION CONTROL PANEL CONTROL LEVER LH CONTROL LEVER RH TRACTION ROD ARM IMPELLER ROD ARM INTERLOCK ROD SPACER RETAINER SCREW 1/4-20 X.62 KNOB BLACK KNOB RED HANDLE KNOB WASHER 3/8 CARRIAGE BOLT 3/8-16 X 2.25
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 9
KEY NO. PART NO. 04-40 57-18 04-18 77-18 04-17 86-18 09-27 05-15 53-16 96-75 DESCRIPTION IMPELLER ROD ASSEMBLY TRACTION ROD ASSEMBLY SHIFTER ROD TOP SHIFTER ROD BOTTOM SPRING SLEEVE IMPELLER SPRING TRACTION SPRING CARRIAGE BOLT 5/16-18 X.75 NUT 5/16-18 RETAINER

01.12.001-E

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 10
KEY NO. PART NO. 10-42 21-42 88-00 06-16

DESCRIPTION LOWER TUBE PIVOT SUPPORT BOLT 5/16-18 X.750 SCREW 3/8-16 X 1.00

01.05.003-C

KEY NO. 7
PART NO. 96-17 86-17 86-18 44-17 52-18 09-40 16-20
DESCRIPTION PANEL CONSOLE HEADLIGHT BEZEL HALOGEN HEADLIGHT SHOULDER SCREW SCREW 1024 X 1.25 WIRE HARNESS BULB

01.10.026-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 11

01.02.011-B_Sheet_1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 12

KEY NO. 35

PART NO. 05-75 11-18 00-93 05-19 95-17 98-17 86-76 05-17 53-00 00-18 00-18 00-19 29-17 92-18 00-18 01-40 54-05 70-42 75-19 85-18 40-18 78-17 88-18 01-18 71-08 51-70 02-42 88-41 67-41 54-41 68-41 54-41 54-40 28-19 17-30
DESCRIPTION BOLT 5/16-18 X.500 NUT 5/16-18 FLANGE BEARING NUT 5/16-18 RUBBER WHEEL PLATE RUBBER WHEEL RING RUBBER WHEEL HUB BOLT 5/16-18 X.875 TRUNNION BEARING ASSEMBLY RETAINER HEX SHAFT PINION GEAR AUXILIARY PLATE SPACER PLATE INTERMEDIATE GEAR AUXILIARY SHAFT CONTROL ARM WASHER CONTROL SHAFT ASSEMBLY CLEVIS PIN SHIFTER LEVER PIVOT BRACKET PIVOT PIN SPRING SHIFTER LINK RETAINER CLIP SCREW 5/16-18 x.750 REAR PLATE SHIFTER PLATE BRACKET CLUTCH PLATE BRACKET SHIFTER PLATE CLUTCH PLATE SHOULDER BOLT 1/4-20 X.500 NUT 1/4-20
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 13

26 01.02.011-B_Sheet_2

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 14

KEY NO. 27

PART NO. 88-50 10-19 77-19 77-17 53-00 00-27 05-18 89-18 25-18 40-18 40-17 86-08 51-40 33-49 05-18 40-15 53-19 10-11 15-04 05-95 05-41 45-17 90-17 88-41 08-18 44-41 66-82
DESCRIPTION SPEED SELECTOR HEAD ASSEMBLY SCREW 10-24 X.625 DRIVE PLATE WELDMENT HEX SHAFT TRUNNION BEARING ASSEMBLY RETAINER CARRIAGE BOLT 5/16-18 X.625 FLANGE BEARING SPACER LEVER SHIFTER PLATE SHIFTER SUPPORT BRACKET PIN RETAINER CLUTCH ROD BOLT 5/16-18 X.500 DRIVE MOUNT PLATE NUT 5/16-18 TRACTION PULLEY WASHER LOCKWASHER 5/16 SCREW 5/16-18 X.750 TRACTION SPRING RETURN SPRING BRAKE SPRING BOTTOM PAN SCREW 10-24 X.625 TRACTION SPRING BRACKET

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 15

1b 8 3

1b 7 1a

01.03.001-A 3

KEY NO. 1 1a 1b 8
PART NO. 49-40 43-18 42-18 00-17 46-17 98-14 63-49 05-15 54-18 92-82
DESCRIPTION (assy of 1a,1b) AXLE ASSEMBLY AXLE SHAFT ROLL PIN 3/16 GEAR THRUST WASHER AXLE BEARING SCREW 5/1618 X.625 BOLT 5/1618 X.500 CLIK PIN SQUARE KEY
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 16

CHASSIS / PULLEYS

KEY NO. -01.00.018-C
PART NO. --------55-15 04-06
DESCRIPTION TECUMSEH ENGINE MODEL OH318SA-221813B FRAME BOLT 3/816

KEY NO. 1 PART NO. 86-84

DESCRIPTION COVER ASSEMBLY

01.21.015-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 17

01.21.003-B

KEY NO. 11 12
PART NO. 80-41 97-42 92-18 05-42 65-78 05-42 92-42 88-42 42-75 11-18 77-18 05-22
DESCRIPTION IMPELLER BELT TRACTION BELT IDLER ARM BRACKET IDLER PULLEY NUT 5/16-18 SCREW 5/16-18 X 1.50 IDLER BRACKET SCREW 5/16-18 X.625 SHOULDER BOLT 5/16-18 X.500 NUT 5/16-18 NYLOCK TRACTION IDLER ARM TRACTION PULLEY

KEY NO. 23 24

PART NO. 05-05 92-80 05-85 10-40 00-42 64-42 64-61 05-04 05-15 54-05 05-17 53-31
DESCRIPTION SCREW 5/16-18 X 1.00 WASHER NUT 5/16-18 SCREW 3/8-24 X 1.375 WASHER PULLEY ENG IMPELLER PULLEY ENG TRACTION SCREW 5/16-18 X 1.00 LOCKWASHER 5/16 BELT GUIDE LOCKWASHER 5/16 IDLER BUSHING
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 18

WHEELS

01.15.001-A
PART NO. 51-18 44-00 00-19 21-18 24-18 76-19 49-17 91-18 92-19 49-17 46-19 95-19
DESCRIPTION COVER SHOULDER SCREW RETAINER RING WHEEL DRIVER RETAINER RING WHEEL LOBE CLUTCH SLIDE SPRING SQUARE KEY AXLE LOBE THRUST WASHER STEERING YOKE
PART NO. 41-49 05-19 95-19 95-18 18-60 04-40 50-70 02-08 51-19 38-18 20-19 95-12
DESCRIPTION STEERING BRACKET SCREW 5/1618 X.50 PIVOT BRACKET BELLCRANK BELLCRANK PIN SCREW 1/420 X.375 STEERING LINK RETAINER RETAINER SPRING LEVER PIN PIVOT BRACKET

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 19

01.06.005-A

PART NO. 95-19 95-04
DESCRIPTION WHEEL 16 X 4.80 X LH WHEEL 16 X 4.80 X RH
KEY NO. PART NO. 52-18 78-59

01.15.002-A

DESCRIPTION STEER CABLE BRACKET LH STEER CABLE BRACKET RH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 20

BAG OF PARTS

01.14.005-C

KEY NO. 10 11

PART NO. 96-42 91-17 98-19 17-25 05-75 11-80 06-13 13-19 20-80 04-00
DESCRIPTION RETAINER PIN WRENCH SHOULDER BOLT 1/420 LOCKNUT 1/420 CARRIAGE BOLT 5/1618 X 5/8 LOCKNUT 5/1618 LOCKNUT 3/816 WASHER 3/8 SHEAR BOLT 1/420 X 13/4 LOCKNUT 1/420

KEY NO. 1

PART NO. 50-62
DESCRIPTION SAFETY IGNITION KEY

01.14.008-A

2.31 01.14.013-A
PART NO. 04-18 77-27 05-15 53-77
DESCRIPTION SHIFTER ROD TOP SHIFTER ROD BOTTOM CARRIAGE BOLT 5/16-18 X.75 NUT 5/16-18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

DECALS

KEY NO. -----
PART NO. 40-19 96-18 40-19 96-18 04-18 40-40 58-40 58-40 58-40 92-49
DESCRIPTION DECAL, FUEL SHUT OFF DECAL, DANGER, DEFLECTOR DECAL, DANGER DECAL, AUGER SAFETY DECAL, NOISE LEVEL DECAL, BELT GUARD OPERATORS MANUAL, EUROPEAN OPERATORS MANUAL, SCANDINAVIAN OPERATORS MANUAL, EAST BLOC OPERATOR'S MANUAL, BALTIC
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 22

www.ersatzteil-service.de

REPAIR PARTS MANUAL

MODEL NUMBER SB270B Snow Thrower

79-07 07.30.03 BY

Printed in U.S.A.
Ihr Ersatzteilspezialist im Internet
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - - MODEL NUMBER SB270B 48
SNOW THROWER - - MODEL NUMBER SB270B
KEY PART NO. NO. DESCRIPTION
38-18 10-17 53-15 53-18 03-27 05-17 88-18 45-18 40-18 40-17 53-11 15-04 05-95 05-17 95-80 04-80 05-15 54-18 40-17 92-27 05-18 56-17 46-17 46-18 74-18 40-18 41-18 41-17 46-17 47-17 46-17 46-17 46-17 46-17 46-15 00-08 64-17 46-17 46-17 47-17 88-17 46-17 46-17 46-18 41-78 04-17 53-18 42-05
Washer, Flat Pulley, Impeller Bearing Assembly, Flange Nut, Hex Flange 5/16-18 Bolt, Flat Head, Carriage 5/16-18 x 5/8 Bolt, Carriage 5/16-x 5/8 Nut, Cage 3/8-16 Housing, Auger Bar, Scraper Bracket, Corner Discharge Base, Discharge Chute Washer, Flat Washer, Lock 5/16 Screw, Hex Head 5/16-18 x 3/4 Screw, Hex Head 5/16 x 1 Nut, Hex Lock 1/4-20 Nut, Hex Lock 5/16-18 Washer, Flat Skid Plate, RH Washer, Nylon, Friction Bolt, Carriage 5/16-18 x 3/4 Bolt, Shoulder Bearing, Auger Washer, Thrust, 1" Bolt, Shear Skid Plate, LH Auger Assembly, RH Auger Assembly, LH O-Ring Bushing, Flange 3/4 Washer, Thrust 3/4 Bearing, Thrust 3/4 Shaft, Impeller Washer, Thrust 5/8 Bushing, Flange 5/8 Screw, Hex Head 5/16-18 x 3/4 Plug, Case Housing, Gearbox, RH Seal, Oil Bushing, Flange, 1" Key, Square 1/4 x 1/4 x 7/8 Gear, Worm Shaft, Auger Housing, Gearbox, LH Impeller Assembly Screw, Hex Head 1/4-20 x 1-5/8 Gasket, Gearbox Pin, Roll 3/16 x 1-1/8
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE
REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE

KEY PART NO. NO.

DESCRIPTION
33-50 10-17 86-80 06-13 13-17 86-18 40-15 00-18 45-17 98-05 38-80 04-25 05-80 05-18 45-18 45-17 91-12 84-18 33-27 05-04 10-15 54-18 76-78 05-15 53-17 92-16 96-18 04-18 77-16
Knob, Lever Screw #10-24 x 5/8 Control Assembly, Deector Nut, Lock 3/8-16 Washer, Flat 3/8 Control Assembly, Chute Rotater Support, Pivot Screw, Hex Head 5/16-18 x 3/4 Spring, Deector Bolt, Shoulder Washer, Flat 1/4 Nut, Lock 1/4-20 Bolt, Carriage 5/16-18 Nut, Lock 5/16-18 Chute Assembly Deector Assembly Seal, Deector Rivet, Blind Knob, Speed Control Lever Bolt, Carriage 5/16-18 x 3/4 Screw #10-24 x 1-1/2 Washer, Flat 5/16 Control Assembly, Power Steering Screw, Hex Head 5/16-18 x 1-3/4 Nut, Lock 5/16-18 Lever Assembly, Speed Control Retainer, Hairpin Rod, Upper, Speed Control Rod, Lower, Speed Control

HANDLES

41-18 41-17 94-17 88-16 96-18 04-17 86-18 40-17 86-18 41-78 05-78 05-18 41-18 41-80 05-13 13-17 88-17 90-17 90-18 04-35 05-12 06-18 40-18 04-18 09-17 86-21 06-18 04-18 29-17 52-18 44-18 41-18 35-06 80-17 88-17 86-17 86-17 86-18 09-64
Lever, Auger Control, RH Lever, Traction Drive Control, LH Nut, Cage 1/4-20 Bushing, Flange Retainer, Hairpin Screw, Hex Head 1/4-20 x 3/4 Rod, Interlock Tube Assembly, Interlock, RH Tube Assembly, Interlock, LH Panel, Control Screw, Hex Head 5/16-18 x 1-1/2 Screw, Hex Head 5/16-18 x 1-3/4 Handle Tube, LH Handle Tube, RH Nut, Lock 5/16-18 Washer, Flat 3/8 Knob, Handle Rod, Auger Control Rod, Traction Control End, Control Rod Nut, Hex, Jam 5/16-18 Bolt, Carriage 3/8-16 x 2-1/4 Handle Tube, Lower Sleeve, Spring Spring, Traction Drive Spring, Auger Control Screw, Hex Head 3/8-16 x 1 Clip, Panel Console, Panel Screw, Hex Head, Tapping #10-24 x 1-1/4 Screw, Hex Head, Tapping #10-24 x 1/2 Latch, Interlock Bolt, Shoulder Nut, Lock 1/4-20 Spring, Torsion Spring, Interlock Headlight, Halogen Bezel, Headlight Harness, Headlight (Halogen)
63-80 05-15 54-49 05-18 00-18 01-17 92-18 40-18 00-18 00-18 77-18 00-17 88-18 40-17 53-18 78-17 98-18 40-93 05-17 86-76 05-08 51-18 01-18 00-17 86-17 53-17 86-17 53-18 40-18 40-27 05-17 88-17 53-18 40-18 25-17 53-15 53-11 15-04 05-95 05-00 00-17 90-18 42-06
Screw, Hex Head 5/16-18 x 3/4 Nut, Lock 5/16-18 Washer, Flat Screw, Hex Head 5/16-18 x 1/2 Bearing, Flange Shaft, Auxiliary Spacer, Plate Plate, Auxiliary Gear, Intermediate (12/58) Gear, Pinion Rod, Clutch Shaft, Long, Hex Pin, Pivot Lever, Shifter / Wheel Trunnion Bearing Assembly Bracket, Pivot, Shift Ring, Rubber Wheel Plate, Rubber Wheel Nut, Lock 5/16-18 Hub, Rubber Wheel Screw, Hex Head 5/16-18 x 7/8 Retainer, Hairpin Spring, Bias Gear, Axle (58 Teeth) Pin, Pivot Lever Plate Assembly, Drive Shaft, Axle Shaft, Short Hex Lever, Shifter Plate Bracket, Shifter Support Bolt, Carriage 5/16-18 x 5/8 Key, Square 1/4 x 1/4 x 7/8 Bearing, Flange Plate, Drive Mounting Spacer, Bearing Pulley, Traction Drive Nut, Lock 5/16-18 Washer, Flat Washer, Lock 5/16 Screw, Hex Head 5/16-18 x 3/4 Ring, Retaining Spring, Return Pin, Roll

REPAIR PARTS CHASSIS / ENGINE / PULLEYS
CHASSIS / ENGINE / PULLEYS
10-44 Spring, Traction Idler 05-22 Pulley, Idler (2-1/4) --Engine, Tecumseh, Model Number OHSK90 (Order parts from Engine manufacturer) 05-20 Screw, Hex Head 5/16-18 x 1-1/05 92-89 Washer, Flat 05-00 Nut, Jam, Lock 5/16-17 53-30 Pin, Idler Pivot 90-92 V-Belt, Traction Drive 05-00 Washer, Lock 5/49 05-08 Screw, Hex Head 5/16-18 x 3/17 92-59 Impeller Idler Arm Assembly 51-79 Retainer, Hairpin 88-28 Spring, Brake 35-33 V-Belt, Impeller Drive 04-06 Screw, Hex Head 3/8-16 x 1-1/18 48-04 Arm, Idler 05-24 Screw, Hex Head 5/16-18 x 1-1/17 53-31 Bushing, Idler Pivot 05-23 Pulley, Idler (2-3/4) 05-16 Screw, Hex Head 5/16-24 x 17 93-71 Spacer, Engine Pulley 04-78 Pulley, Engine, Traction Drive 91-57 Pulley, Engine, Impeller Drive 27-35 Washer, Flat 3/85 02-63 Washer, Lock 3/85 10-84 Screw, Hex Head 3/8-24 x 1-3/15 54-52 Guide, Belt 04-65 Cover, Belt 88-30 Cover, Toolbox 04-08 Screw, Hex Head 1/4-20 x 1/17 92-56 Bolt, Shoulder 5/16-18 78-53 Bellcrank Shifter 04-01 Screw, Hex Head 1/4-28 x 3/17 92-40 Arm, Auger Control 05-00 Nut, Lock 5/16-18 40-86 Bellcrank Assembly 71-01 Link, Speed Control 90-64 Trunnion, Clutch 88-90 Nut, Cage 3/8-70 02-79 Pin, Cotter 3/32 x 1/17 90-65 Pin, Bellcrank 40-85 Bracket, Bellcrank 06-24 Screw, Hex Head 3/8-16 x 1-1/18 40-74 Pivot Bracket, Impeller Idler Arm 40-84 Pan, Frame Bottom 05-12 Screw, Hex Head 5/16-18 x 3/18 11-56 Nut, Speed 5/16-18 45-07 Frame Assembly 83-69 Plate, Frame End 40-82 Shaft, Auger Control 70-79 Washer, Hardened 90-62 Roller 00-10 Ring, Retaining
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 11

WHEELS

78-15 54-18 18-18 44-80 05-15 54-21 06-18 78-18 78-14 63-49 05-18 43-18 78-18 20-18 43-18 19-18 20-18 18-08 51-18 41-17 91-18 24-17 91-17 91-17 91-17 91-17 88-17 46-17 98-18 44-18 78-70 02-00 00-45
Wheel Assembly, 16", Power Steering, LH Pin, Klik 1/4 Cover, Power Steering Bolt, Shoulder #10-24 x 1/2 Nut, Lock 5/16-18 Washer, Flat 5/16 Screw, Hex Head 3/8-16 x 1 Bracket, Steering Cable, RH Bracket, Steering Cable, LH Screw, Hex Head 5/16-18 x 5/8 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Yoke, Steering Pin, Steering Lever Bellcrank Assembly Bracket Assembly, LH Steering Bracket Assembly, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Lever Assembly Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 Washer, Thrust (1") Bearing, Axle Spring, Return Wheel Assembly, 16", Power Steering, RH Clip, Retainer Ring, Retaining

DECALS

40-18 79-18 40-18 40-18 79-18 40-18 40-18 40-18 40-18 40-18 39-18 39-18 41-18 04-18 40-18 40-18 42-18 42-18 42-18 79-07
Decal, Danger Decal, Partner, 69cm Decal, Danger, Deector Decal, Instruction, Owner's Manual Decal, Partner / Electrolux Decal, Instruction Decal, Traction Lever Decal, Auger Lever Decal, Speed Control Decal, Remote Deector Decal, LH Trigger Decal, RH Trigger Decal, Height Adjustment Decal, Sound Level Decal, Belt Guard Decal, Fuel Shut-Off Operators Manual, European Operators Manual, Scandinavian Operators Manual, East Bloc Euro Repair Parts Manual, English

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we nd to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions: 1. 2. This warranty does not apply to the engine. Please contact your nearest dealer where they will send the machine to the engine manufacturer. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by your dealer. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we nd to be defective in manufacture, during the rst ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must be maintained in accordance with the instructions furnished. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original purchase. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product. Exclusions: Excluded from this Warranty are belts, normal wear, normal adjustments, standard hardware and normal maintenance. In case of any problem within the boundaries of this warranty, contact the nearest department store, indicate the model number, serial number and the date of purchase of your machine. This warranty does not apply to accidental damages. All implicit warranties are limited to the same time frames. Or contact:
E.M. Services 54 Rue Lambrechts 92400 Courbevoie France Telephone: (1) 46678078 Fax: (1) 46678095
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES. ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN.