GAUCHO ROCKIN

Model Number IGOD0024

PEG PEREGO S.p.A.

via DE GASPERI ARCORE (MI) ITALIA tel. 03960881 fax 039615869-616454 assistenza: tel. 0396088213 fax 0393309992

PEG PEREGO U.S.A Inc.

3625 INDEPENDENCE Dr. FORT WAYNE IN 46808 phone 2604828191 fax 2604842940 call us toll free 18007282108 llame USA gratis 18002251558 llame Mexico gratis 18007101369

PEG PEREGO CANADA Inc.

585 GRANITE COURT PICKERING ONT. CANADA L1W3K1 phone 9058393371 fax 9058399542 call us toll free 18006615050

www.pegperego.com

Conforms a EN 50088 Recargeable battery 12V 12Ah sealed lead-acid battery. Two 230W motors
terminal C. 49 Once the battery has been recharged, unplug the battery charger from the wall outlet, then disconnect terminals C and B. 50 Connect terminal B and A till you hear the final click. Once recharging is complete, don't forget to close the simulated motor with the screw. REPLACING BULBS (3,5 VOLT) 2 spare bulbs, placed underneath the imitation motor, are included with the product.To facilitate its removal, turn the bulb and pull it out at the same time. HEADLIGHTS 51 Remove the glass covering the headlight, levering it out with a tool. 52 Take out the non functioning bulb and its housing. Holding the housing still, unscrew the bulb and replace it with a spare one. Reposition the glass covering the front headlight using pressure. REARLIGHTS 53 Remove the glass covering the rearlight, levering it out with a tool. 54 Take out the non functioning bulb and its housing. Holding the housing still, unscrew the bulb and replace it with a spare one. Reposition the glass covering the rearlight using pressure.
as shown in the figure. 22 On top of these adhesives, place the 2 plastic signs, pressing down as you do so. 23 Apply adhesive no.1 (see adhesive sheet) to the antenna. Insert the antenna, pressing down as you do so, into its appropriate housing, situated on the right rear mudguard. 24 Unscrew the panel. 25 Once you have removed the panel, fit the battery (9V -not included) into its holder, taking care to respect correct polarity. 26 Connect the wires to the battery. Screw the panel back on. 27 Fit the horn unit into the hole in the middle of the steering wheel. 28 Remove the radio from its packaging. Unscrew the cover from the battery chamber. Insert two 1.5 Volt AA batteries (not supplied with the vehicle) into the compartment, taking care to position the positive and negative poles correctly. Close the battery compartment cover and screw into place. 29 Insert the wire from the antenna and the radio into their appropriate housing on the dashboard, making sure to place them the right way up, as shown in the figure. 30 Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine. 31 Plug battery terminal A into vehicle wiring terminal B. 32 Lower the imitation motor and screw it down again. Close the hood, securing it in place with the 2 hooks. The vehicle is now ready for use. VEHICLE FEATURES AND INSTRUCTIONS FOR USE 33 Hood support shaft. 34 Below the box you can find four removable toy tools. To remove the box, pull out and unfasten the four couplings. 35 A: HORN. Push the yellow button the horn will sound. B: RADIO. A real autoradio, which is removable and can function independently. To switch on, press button 3 (for AM frequency) or button 4 (for FM frequency). To switch off, press button 5. To tune the frequency, use control 1. To control the volume, use control 2. To change the clock, hold down the SET button, and simultaneously press down the HOUR button to change the hour and the MIN button to change the minutes. C: SIMULATED START-KEY. The key provided is only a toy key and does not turn the vehicle , on or off. D: Accelerator/electric brake pedal. The electric braking system stops the vehicle automatically when your child lifts his foot off the pedal. 36 To unfasten the safety belts:1 push towards the middle and simultaneously press the button; 2 detach the buckle. 37 GEAR SHIFT LEVERS: 1: first speed. 2: second speed. R: reverse. 38 SECOND SPEED: When the red lock-out is positioned as shown in the figure, the vehicle will run in first speed and reverse only. The turtle on the lock-out is in the up position. To use the second gear, follow the instructions: loose the screw on the red lock-out. 39 Remove the red lock-out. 40 Rotate it 180 until the hare is in the up position. Insert the lock-out into the hole provided. 41 Tighten the screw. By pushing the gearshift lever backward, the vehicle moves into second gear. REPLACING THE BATTERY 42 Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine. 43 Unscrew and remove the battery fastener. 44 Replace the battery. Replace the battery fastener. 45 Connect the two plugs. 46 Replace simulated engine in vehicle and secure with screw. BATTERY RECHARGE WARNING: BATTERY CHARGING AND EVERY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE CARRIED OUT BY ADULTS ONLY. THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE TOY. 47 Disconnect the electrical system terminal A from the battery terminal B pressing with the fingers on the sides. 48 Plug the battery charger terminal to a wall outlet following the instructions provided. Connect the terminal B and the battery charger

Years 3 - 8

ASSEMBLY 1 Place from bumper on body and tighten four screws as shown in the drawing. 2 Take out the 2 bulbs placed on the bottom of the rear part of the vehicle (in the area of the shock absorbers). Proceed by inserting the bulbs into the rear bumper, as shown in the figure. 3 Place rear bumper on body. 4 Tighten three screws as shown in the drawing. 5 Put the tool box on the bonnet and fix it as shown in the figure. 6 Assemble the two parts of the steering wheel. 7 Insert the steering wheel on the steering wheel column. 8 Align steering wheel column holes with steering wheel: nut fits into haxagon hole, bolt into round hole. 9 Insert the windscreen. 10 Secure it by means of the two screws. 11 Fit the removable seat cover as shown in the figure. 12 Hook the front elastic bands. 13 Position the other two elastic bands. 14 Place seat on body. Adjust seat position. Secure it with washer and thumb nut. 15 Detach parts A and C of the Roll-Bar; join A to B; 16 join A-B to the upper section of the Roll-Bar C, insert and rotate to secure. 17 Place Roll-Bar on body. Tighten four screws as shown in the drawing. 18 Screw the net down to the body. 19 Snap it around the roll-bar as shown in the drawing. 20 Insert the rearview mirrors in the direction shown by the arrow. 21 Apply the 2 adhesives nos. 6D and 6S (see adhesive sheet) to the 2 sides of the bodywork,

36 32b 60 47

MEPU0003 MEPU0002

ELECTRONIC CARD

MEDI0014

MEPU0001 bk w

SAGI0050

MOTOR RIGHT SAGI9995

LIGHTS SYSTEM

MOTOR LEFT

GAUCHO ROCK'IN

SAGI9995

SAGI0050 IKCB. MMEV0266 SPST3833N
LAMP MEVA0028 r MEPU0003 MEPU0002 LAMP MEVA0028 MEDI0014

FRONT LIGHTS bk

REAR LIGHTS

TIMER MEVA0023

b r LAMP MEVA0028

MEIE0466

LAMP MEVA0028

b r r R

M2+ M1+

MEPU0001

r bk w b

31 32a 32b 51 52

MOTOR RIGHT
QRCG = b OSCG = bk MCG = r HCG = w
ASGI0135NA SAGI3263NA SPST0132 SPST3821KM ASGI0053A SOPF1639L30 IAKB0015 SPST8235N SAGI3029GR SAGI0183GR SPST8210N ASGI0118RGR ASGI0024R ASGI0122GRN ASGI0054GR SAGI0127N SAGI3822KN SPST0465 MEVA0021 SPST8609GR ASGI0016R SAGI3969N CSGAUC00-QL79RI53 SPST0452N SAGI0445KR SAGI0162N SAGI0321R SPST3867N ASGI0043GPN SPST3562N SPST3508N SPST3824N SPST3823N SPST3839R SPST3507GP SAGI0318KN SPST3055A/RF SPST3552N ASGI0056R SARP3513NGR SOFF0489L30 SPST3627N SAGI9970 SOFF2075L30 SPST3546N SAGI3510XN ASGI0094Y SAGI3977JY SPST3185R SPST3522R SPST3827M SPST3511R SAGI0705 SAGI0709 SPST0316N SPST3538GR SARP3512NGR SPST3102N SPST0283 SOTF1693L30 SPST0315KGR MEVA0028 MEVA0023 MEIE0466

FIMX0701G29

EN ES FR

USE AND CARE EMPLEO Y MANUTENCION UTILISATION ET ENTRETIEN
MONTABLE PARA NIOS MARCA: GAUCHO ROCK'IN MODELO: IGOD0024US ESPECIFICACIONES ELECTRICAS 12 V c.c. INCLUYE: CARGADOR DE BATERIA c.a./c.c. MODELO: 25200011 HECHO EN CHINA MARCA: PEGPEREGO ENTRADA: 120 V ~ 60 Hz 16 W SALIDA: 12 V c.c. 12 W BATERIA RECARGABLE MARCA: PEG-PEREGO 12 V c.c. 12Ah RADIO FM 3 V c.c. (EMPLEA 2 BATERIAS TIPO "AA") ANTES DE USAR EL PRODUCTO LEA EL INSTRUCTIVO Y CONSERVELO SI EL CORDON DE ALIMENTACION ES DAADO, ESTE DEBE SER REEMPLAZADO POR EL FABRICANTE O SU AGENTE DE SERVICIO O POR PERSONAL CALIFICADO PARA EVITAR EL RIESGO. IMPORTADOR: COMERCIALIZADORA MEXICO AMERICANA, S. DE R.L. DE C.V. AV. NEXTENGO No. 78, COL. SANTA CRUZ ACAYUCAN, DEL. AZCAPOTZALCO, MEXICO D.F. C.P.02770, R.F.C. CMA 9109119L0 TEL. 5899-1200
Requires 2 AA batteries and 1 9-volt battery (not included) Requerir 2 AA bateras e 1 9-voltios battera (no inclusa) Exige 2 batteries de AA et 1 batterie de 9 volt (ne pas inclus)

GAUCHO ROCKIN

Model Number IGOD0024
SEE VERBAL INSTRUCTIONS AFTER THE PICTURES VER LAS INSTRUCCIONES DESPUS DE LOS DISEOS VOIR LES INSTRUCTIONS APRS LES DESSINS
ASSEMBLY MONTAJE MONTAGE 1

C A B A

VEHICLE FEATURES AND INSTRUCTIONS FOR USE CARACTERSTICAS Y USO DEL VEHCULO CARACTERSTIQUES ET UTILISATION DU VEHICULE

SET HOUR MIN

- VOLUME +

A 36 C D 37

davanti front devant vorn delante parte dianteira n dietro posterior arrire heck trasera parte traseira arka
REPLACING THE BATTERY CAMBIO DE LA BATERA REPLACEMENT DE LA BATTERIE 41 42
BATTERY CHARGING CARGA DE LA BATERA CHARGE DE LA BATTERIE 46 47
REPLACING BULBS PARA CAMBIAR LAS BOMBILLAS REPLACEMENT DES AMPOULES

b r LAMP MEVA0028

FRONT LIGHTS bk

LAMP MEVA0028

TIMER MEVA0023
b REAR LIGHTS r LAMP MEVA0028

MEIE0466

THERMO PROTECTOR bk

MOTOR RIGHT

52033 N?

SAGI9995

MOTOR LEFT

MEIE0480

b w SAGI9995

MEPU0001

GAUCHO ROCK'IN
b = blue bk = black r = red w = white b = azul bk = negro r = rojo w = blanco b = bleu bk = noir r = rouge w = blanc
MEIE0480 IKCB. MMEV0266 SPST3833N

59 32a 8 26

36 32b 48
ELECTRONIC CARD TARJETA ELECTRNICA CARTE ELECTRONIQUE

REAR LIGHTS r

b LAMP MEVA0028
LIGHTS SYSTEM INSTALACIN LUCES SYSTEME DECLAIRAGE

31 32a 32b 61 62

ASGI0135NA SAGI3263NA SPST0132 SPST3821KM ASGI0053A SOPF1639L30 IAKB0015 SPST8235N SAGI3029GR SAGI0183GR SPST8210N ASGI0118RGR ASGI0024R ASGI0122GRN ASGI0054GR SAGI0127N SAGI3822KN SPST0465 MEVA0043 SPST8609GR ASGI0016R SAGI3969N CSGAUC00-QL79RI53 SPST0452N SAGI0445KR SAGI0162N SAGI0321R SPST3867N ASGI0043GPN SPST3562N SPST3508N SPST3824N SPST3823N SPST3839R SPST3507GP SAGI0318KN SPST3055A/RF SPST3552N ASGI0056R SARP3513NGR SOFF0489L30 SPST3627N SAGI9970 SOFF2075L30 SPST3546N SAGI3510JJN ASGI0188R SAGI3977JY SPST3185R SPST3522R SPST3827M SPST3511R SAGI8744N SPST0316N SPST3538GR SARP3512NGR SPST3102N SPST8741N SOTF1693L30 SPST0315KGR MEVA0028 MEVA0023 MEIE0466

ENGLISH

PEG PEREGO thanks you for choosing this product. For over 50 years, PEG PEREGO has been taking children for an outing: first with its famous baby carriages and strollers, later with its pedal and battery operated toy vehicles. Read this instruction manual carefully to learn the use of this vehicle and to teach your child safe and enjoyable driving. Please keep this manual for use as a reference in the future. Our toys conform with the safety requirements provided by the Council of the EEC, of the T.V.; of the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and the U.S. Consumer Toy Safety Specification F963. Peg Perego S.p.A. is an ISO 9001 certified company. The fact that we are certified provides a guarantee of our honesty for our customers, and fosters trust in the companys way of working. Peg Perego reserves the right to modify or change their product. Price, literature, manufacturing processes or locations or any combination of these above mentioned entities may change at any time for any reason without notice with impunity.
Years 3-8 Weight capacity 130 lbs CAUTION:
ELECTRIC VEHICLE NOT RECOMMENDED FOR CHILDREN UNDER 3 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK. RECHARGER INCLUDED.120 VOLTS, 60Hz, 30W INPUT, 12 VOLTS (DC) OUTPUT.

CUSTOMER SERVICE

PEG PEREGO offers after-sales services, directly or with a network of authorized service centers for repairs or replacement parts. See the back cover of this instruction manual for contact information.
steering wheel: nut fits into haxagon hole, bolt into round hole. 9 Insert the windscreen. 10 Secure it by means of the two screws. 11 Fit the removable seat cover as shown in the figure. 12 Hook the front elastic bands. 13 Position the other two elastic bands. 14 Place seat on body. Adjust seat position. Secure it with washer and thumb nut. 15 Detach parts A and C of the Roll-Bar; join A to B; 16 join A-B to the upper section of the Roll-Bar C, insert and rotate to secure. 17 Place Roll-Bar on body. Tighten four screws as shown in the drawing. 18 Insert the end of the safety belt in the slot situated centrally in the bottom of the seat, as shown in the figure. 19 Screw the net down to the body. 20 Snap it around the roll-bar as shown in the drawing. 21 Insert the rearview mirrors in the direction shown by the arrow. 22 Apply the 2 adhesives nos. 6D and 6S (see adhesive sheet) to the 2 sides of the bodywork, as shown in the figure. 23 On top of these adhesives, place the 2 plastic signs, pressing down as you do so. 24 Apply adhesive no.1 (see adhesive sheet) to the antenna. Insert the antenna, pressing down as you do so, into its appropriate housing, situated on the right rear mudguard. 25 Unscrew the panel. 26 Once you have removed the panel, fit the battery (9V -not included) into its holder, taking care to respect correct polarity. 27 Connect the wires to the battery. Screw the panel back on. 28 Fit the horn unit into the hole in the middle of the steering wheel. 29 Remove the radio from its packaging. Unscrew the cover from the battery chamber. Insert two 1.5 Volt AA batteries (not supplied with the vehicle) into the compartment, taking care to position the positive and negative poles correctly. Close the battery compartment cover and screw into place. 30 Insert the wire from the antenna and the radio into their appropriate housing on the dashboard, making sure to place them the right way up, as shown in the figure. 31 Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine. 32 Plug battery terminal A into vehicle wiring terminal B. 33 Lower the imitation motor and screw it down again. Close the hood, securing it in place with the 2 hooks. The vehicle is now ready for use. VEHICLE FEATURES AND INSTRUCTIONS FOR USE 34 Hood support shaft. 35 Below the box you can find four removable toy tools. To remove the box, pull out and unfasten the four couplings. 36 A: HORN. Push the yellow button the horn will sound. B: RADIO. A real removable car radio that works independently. To switch on, press key 3 FM. To switch off, press key 4. To tune using the automatic search function, turn knob 1. Once the radio is turned off, the station does not stay in the memory. To adjust the volume turn knob 2. To adjust the clock, keep the SET key pressed and set the time by using the HOUR and MIN keys. C: SIMULATED START-KEY. The key provided is only a toy key and does not turn the vehicle , on or off. D: Accelerator/electric brake pedal. The electric braking system stops the vehicle automatically when your child lifts his foot off the pedal. 37 To unfasten the safety belts:1 push towards the middle and simultaneously press the button; 2 detach the buckle. 38 GEAR SHIFT LEVERS: 1: first speed. 2: second speed. R: reverse. 39 SECOND SPEED: When the red lock-out is positioned as shown in the figure, the vehicle will run in first speed and reverse only. The turtle on the lock-out is in the up position. To use the second gear, follow the instructions: loose the screw on the red lock-out. 40 Remove the red lock-out. 41 Rotate it 180 until the hare is in the up position. Insert the lock-out into the hole provided. 42 Tighten the screw. By pushing the gearshift lever backward, the vehicle moves into second gear.

REPLACING THE BATTERY 43 Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine. 44 Unscrew and remove the battery fastener. 45 Replace the battery. Replace the battery fastener. 46 Connect the two plugs. 47 Replace simulated engine in vehicle and secure with screw. BATTERY RECHARGE

WARNING:

WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE CARRIED OUT BY ADULTS ONLY. THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
48 Disconnect the electrical system terminal A from the battery terminal B pressing with the fingers on the sides. 49 Plug the battery charger terminal to a wall outlet following the instructions provided. Connect the terminal B and the battery charger terminal C. 50 Once the battery has been recharged, unplug the battery charger from the wall outlet, then disconnect terminals C and B. 51 Connect terminal B and A till you hear the final click. Once recharging is complete, don't forget to close the simulated motor with the screw. REPLACING BULBS (3,5 VOLT) 2 spare bulbs, placed underneath the imitation motor, are included with the product.To facilitate its removal, turn the bulb and pull it out at the same time. HEADLIGHTS 52 Remove the glass covering the headlight, levering it out with a tool. 53 Take out the non functioning bulb and its housing. Holding the housing still, unscrew the bulb and replace it with a spare one. Reposition the glass covering the front headlight using pressure. REARLIGHTS 54 Remove the glass covering the rearlight, levering it out with a tool. 55 Take out the non functioning bulb and its housing. Holding the housing still, unscrew the bulb and replace it with a spare one. Reposition the glass covering the rearlight using pressure.
BATTERY MAINTENANCE AND SAFETY
Before riding, charge your battery for 18 hours to initiate them. Failure to do this will result in permanent battery damage.

ASSEMBLY INSTRUCTIONS

CAUTION:
ADULT ASSEMBLY REQUIRED. USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE HAZARD. BATTERY ALREADY INSTALLED IN VEHICLE.
ASSEMBLY 1 Place from bumper on body and tighten four screws as shown in the drawing. 2 Take out the 2 bulbs placed on the bottom of the rear part of the vehicle (in the area of the shock absorbers). Proceed by inserting the bulbs into the rear bumper, as shown in the figure. 3 Place rear bumper on body. 4 Tighten three screws as shown in the drawing. 5 Put the tool box on the bonnet and fix it as shown in the figure. 6 Assemble the two parts of the steering wheel. 7 Insert the steering wheel on the steering wheel column. 8 Align steering wheel column holes with
Only adults should recharge batteries, never children. Never allow children to handle batteries. Only use the batteries specified by the manufacturer. Only use the charger specified by the manufacturer. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. CHARGING THE BATTERY Charge the batteries no longer than 24 hours, following the

instructions enclosed with the battery charger. Charge the battery, as the vehicle shows low power, in this way you will avoid damage to the battery. If you dont use your vehicle for a long period of time unplug the battery from the main wire harness of the vehicle. Remember to charge the battery at least every three months. Never charge the battery upside down. Do not forget batteries during charging! Check them periodically. Never use a replacement recharger or batteries unless they are approved by PEG PEREGO. Batteries are sealed and maintenance free. Battery polarity must be observed when connecting battery to wiring.

CAUTION 1,5V 9V BATTERY

The insertion of batteries must only be carried out or supervised by adults. Do not let children play with the batteries. The batteries should be replaced by an adult. Use only the type of battery specified by the manufacturer. Respect the polarity +/ Do not allow the batteries to be in contact with metal parts (risk of fire or explosion). Always remove the batteries if the toy is not in use for a long period. Never attempt to charge batteries that are not rechargeable. Remove dead batteries from the toy. Dispose of dead batteries into appropriate containers provided for their recycling.
power. After 10 or more seconds,the circuit breaker will automatically reset, however you must eliminate overload conditions to resume normal driving. Periodically lubricate (with a light weight oil) moving parts, such as wheel bearings, steering linkages, where they rotate or touch one another. The vehicles surface can be cleaned with a dampcloth. Do not use abrasive cleaners. The cleaning must be carried out by adults only. Never disassemble the vehicle mechanisms or motor unless authorized by PEG PEREGO. Conforms a EN 50088 Recargeable battery 12V 12Ah sealed lead-acid battery. Two 230W motors SAFETY
BATTERIES CONTAIN TOXIC AND CORROSIVE SUBSTANCES. DO NOT TAMPER WITH THEM. Batteries contain an acid-based electrolyte. Do not make direct contact between battery terminals, as this can cause an explosion or fire. Charging produces explosive gases. Charge batteries in a well ventilated area away from sources of heat and flammable materials. Exhausted batteries are to be removed from the vehicle. Do not place the batteries near clothing to avoid damage. IF A LEAK DEVELOPS Shield your eyes. Avoid direct contact with the electrolyte, protect your hands. Place battery in a plastic bag and follow directions listed below. IF ELECTROLYTE COMES IN CONTACT WITH SKIN OR CLOTHING Flush with cool water for at least 15 minutes. See a physician at once. IF ELECTROLYTE IS INGESTED Give tap water, milk of magnesia or egg whites at once. Do not induce vomiting. See a physician at once. DISPOSAL OF BATTERIES Help protect the environment! Do not throw used batteries in your regular, household trash. Dispose of the old batteries in an approved dumping station; contact your local environmental protection agency office for further information.

To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than 2 riders. Surfaces that are appropriate for safe use: grass, gravel, hard surfaces, slopes modarate. Not suitable for children under the age of 36 months. The small pieces could be swallowed or inhaled. Never use the vehicle on steep slopes or near steps or stairs. This vehicle is not suitable for use on public highways. Do not allow children to place their hands, feet or any part of their body, clothing or other articles near the moving parts while vehicle is in operation. Do not allow the electrical components, motors, wiring, switches of your motorized vehicle to become wet and never wash it with a hose. Never use gasoline or other flammable substances near the vehicle. The vehicle is designed just for two child: never allow more than two rider. Please note that the seat belts are designed for play use only and DO NOT provide any protection.
VEHICLE MAINTENANCE AND SAFETY
This product conforms to EN 71 and conforms to EN 50088 safety standard for electric toys. This vehicle is not intended for use on streets, around traffic or parked cars. This product meets and/or exceeds all ASTM TOY SAFETY STANDARDS, including F 963, Consumer Toy Safety Specifications. MAINTENANCE AND CARE Regularly check the conditions of the vehicle, particularly the electrical system, the plug connections, the covering caps and the charger. In case of fault, do not try to use the vehicle and the charger. For repair use only original PEG PEREGOs spare parts. PEG PEREGO assumes no liability if the electrical system is tampered with. Do not leave vehicle or batteries near sources of heat such as radiators, stoves, fireplaces, etc. Protect vehicle from water, rain, snow, etc. It can operate on grass, dirt or hard surfaces. When operating in overload conditions, such as soft deep sand, mud or rough uneven terrain, the overload circuit breaker will automatically disconnect the

RULES FOR SAFE DRIVING

DON'T STOP THE FUN: always have freshly charged, back-up batteries on hand. For your childs safety: please read and follow all instructions below
before operating. 2nd SPEED Initially we suggest using only the 1st speed and the reverse gear. Before moving into 2nd speed be sure that the child has become familiar with operating the vehicle. 1ST SPEED slow speed (beginner drivers): With both hands on the steeringwheel, press down on the accelerator pedal; the vehicle goes forward at 2,5 mph. 2ND SPEED fast speed (experienced drivers): With both hands on the steeringwheel, press down on the accelerator pedal; the vehicle goes forward at 5 mph. REVERSE: Place the left hand on the steeringwheel. With the right hand holding the gearshift in reverse, press your foot down on the accelerator; the vehicle reverses at 2,5 mph. (Reverse is spring-loaded for safety). BRAKE: The electric braking system stops the vehicle automatically when your child lifts his foot off the pedal. Teach your child the proper use of this vehicle for a safe and fun play time. Before starting be sure that the way is free from people and objects. Drive with both hands on the steeringwheel and keep your eyes on the road at all times. Stop in time to avoid accidents. Use the 2nd speed only after your child has the maturity and the reflexes to operate the vehicle safely.