Refer to p.32 - p.33 on how to open/close the battery/card cover and remove the battery.
Insert the DC coupler while holding down the battery lock lever.
Confirm the DC coupler is locked in place.
Extract the DC coupler cord.
Pull out the tab at the joint of the camera and the battery/card cover so that the DC coupler cord is extracted from there.
Connect the DC terminal of the AC adapter to the DC terminal of the DC coupler. Connect the AC plug cord to the AC adapter. Plug the AC plug cord into the power outlet.
Make sure that the camera is turned off before connecting or disconnecting the AC adapter. Make sure that the AC plug cord and the DC terminal connecting the AC adapter to the camera are inserted securely. Data may be lost if either becomes disconnected while data is being recorded on the SD Memory Card or the built-in memory. Use the AC adapter with due care to avoid fire or electric shock. Be sure to read About the Battery Charger and the AC Adapter (p.2) before using the AC adapter. Be sure to read the operation manual accompanying the AC adapter kit K-AC88 before using the adapter. When connecting the AC adapter, you cannot set the camera upright on the table because the cord from the DC coupler comes out of the bottom of the camera. Additionally, do not place the camera with the lens facing down because the lens extends when the camera turns on. Hold the camera in your hand or use a tripod when using the AC adapter.
Installing the SD Memory Card
This camera uses either an SD Memory Card or an SDHC Memory Card. (Both cards are referred to as SD Memory Cards hereafter.) Captured images and sound files are saved on the SD Memory Card if a card is inserted in the camera. They are saved in the built-in memory if a card is not inserted (p.41).
Be sure to use this camera to format (initialize) an SD Memory Card that is unused or has been used on other cameras or digital devices. Refer to Formatting an SD Memory Card (p.188) for instructions on formatting. Make sure that the camera is turned off before inserting or removing the SD Memory Card. The still picture storage capacity varies depending on the capacity of the SD Memory Card and the selected number of recorded pixels and quality level (p.40). The self-timer lamp blinks while the SD Memory Card is being accessed (data is being recorded or read).

Backing Up Data

The camera may not be able to access data in the built-in memory in the case of a malfunction. Use a computer or other device to back up important data in another location.
Battery/card cover SD Memory Card

SD Memory Card socket

Insert the SD Memory Card into the SD Memory Card socket so that the label is facing toward the front of the camera (the side with the lens).

Hometown

City DST

New York

The frame moves to [DST] (Daylight Saving Time).
Use the four-way controller (45) to select O or P. Press the 4 button.
The [Initial Setting] screen reappears.
Press the four-way controller (3) to select [Settings complete].
The [Date Adjustment] screen appears. Next, set the date and time.
The video output format (NTSC/PAL) is set to the format of the city selected in [Hometown] on the [Initial Setting] screen. Refer to List of World Time Cities (p.239) for the video output format of each city set as the initial setting, and Changing the Video Output Format (p.197) for changing the setting of the video output format.
Setting the Date and Time
Set the current date and time and the display style.
The frame moves to [mm/dd/yy].
Use the four-way controller (23) to choose the date and time display style.
Choose from [mm/dd/yy], [dd/mm/yy] or [yy/mm/dd].
Date Adjustment Date Format

mm/dd / yy 24h

01/01/2009

00:00 Settings complete

The frame moves to [24h].
Use the four-way controller (23) to select [24h] (24-hour display) or [12h] (12-hour display).
The frame returns to [Date Format].
The frame moves to [Date].
The frame moves to the month.
Date Adjustment Date Format mm/dd / yy 24h
Use the four-way controller (23) to change the month.
Change the day and year in the same manner. Next, change the time. If you selected [12h] in Step 4, the setting switches between am and pm corresponding to the time.
Date Adjustment Date Format mm/dd / yy 24h 01/01/2009 00:00 Settings complete
Date Adjustment Date Format Date Time
mm/dd/yy 24h 01/01/2009 00:00

Settings complete

This confirms the date and time. Next, specify the Vertical Snap setting.
If you press the 4 button in Step 10, the camera clock is reset to 00 seconds. To set the exact time, press the 4 button when the time signal (on the TV, radio, etc.) reaches 00 seconds.

Vertical Snap Setting

The O (Vertical Snap) function enables you to take pictures with the camera held vertically, as if it was a cellphone. To use this function, first set Vertical Snap setting here. See Simple Cellphone-style Picture Taking (Vertical Snap) (p.80) for details.
Use the four-way controller (23) to select [On] or [Cancel].
On Enables Vertical Snap shooting. Cancel Disables Vertical Snap shooting.
Vertical Snap Snaps vertical shots like a cellphone, using OK button

On Cancel

This confirms the Vertical Snap setting and completes the initial setting. The camera returns to capture status.

Green/i button

Switches from single-image display to the Delete screen (p.146). Switches from four-/nine-image display to the Select & Delete screen (p.148). Switches from folder display to the calendar display screen (p.133). Switches from calendar display to the folder display screen (p.133).
Switching Between A Mode and Q Mode
In this manual, the capture mode, such as for taking still pictures, is referred to as A mode (the capture mode). The playback mode, such as for displaying captured images on the display, is referred to as Q mode (the playback mode). In Q mode, you can perform simple editing operations on the captured images. Follow the procedure below to switch between A mode and Q mode. To Switch from A Mode to Q Mode

Press the Q button.

The camera switches to Q mode.
To Switch from Q Mode to A Mode
Press the Q button or the shutter release button halfway.
The camera switches to A mode.
Displaying data stored in the built-in memory When an SD Memory Card is inserted in the camera, images, movies, and sounds on the SD Memory Card are displayed. If you want to display images, movies and sounds in the built-in memory, turn the camera off and remove the SD Memory Card, or follow the procedure below to use the Built-in memory display function.
Make sure that the camera is turned off before inserting or removing the SD Memory Card. Viewing images in the built-in memory while the SD Memory Card is inserted (built-in memory display) When you press and hold down the Q button for more than one second in A mode, the lens is retracted. After the message [Display image/sound from built-in memory] appears, images, movies and sound files stored in the builtin memory are displayed. In the built-in memory display, you can play back still pictures (including enlarged display) (p.130, p.143), movies (p.131) and sounds (p.182), and switch between four-/nine-image display, folder display and calendar display (p.132). In the built-in memory display, you cannot delete data, delete a selection, display the Playback Mode Palette or display the menu. If you want to perform any of these operations on images, movies or sounds in the builtin memory, do so after removing the SD Memory Card.
Setting the Camera Functions
To change the camera settings, press the 3 button to display the [A Rec. Mode] menu or [W Setting] menu. Menus for playing back and editing images and sound files are displayed from the Playback Mode Palette (p.134). 2

Operating the Menus

Press the 3 button to change the number of recorded pixels.
The number of recorded pixels is changed as follows each time the 3 button is pressed: E f m E.
Press the Green button to change the flash mode.
The flash mode is switched between , (Auto) and a (Flash Off) each time the Green button is pressed.
Use the four-way controller (2345) to adjust the zoom and exposure.
The directions on the four-way controller are OK MENU also realigned when you hold the camera 12M vertically: Four-way controller (2/b) Telephoto Four-way controller (3/q) Wide-angle Four-way controller (4/MODE) Exposure compensation () Four-way controller (5/g) Exposure compensation (+)
To exit the O mode, press the power switch.
The camera turns off. Press the power switch again to take a picture in normal shooting mode.
The following settings are used when shooting: - Focus Mode 3 (Pan Focus) - Drive Mode 9 (Standard) - Sensitivity Auto (sensitivity 64 - 1600) - Pixel Track SR P (Off) You can also use the shutter release button to take pictures in O mode. When you press the shutter release button halfway to set the focus, the camera takes the picture at the = (Standard) setting. If the subject is out of focus, the camera takes the picture at the 3 (Pan Focus) setting. The default flash mode is a (Flash Off). When the flash mode is set to , (Auto), the message [Be careful to keep fingers away from flash] appears for 2 seconds. Please take care not to cover the flash with your hand. The zoom lever does not function in O mode. The camera automatically turns off if it is not used for 5 minutes in O mode.
To Select Vertical Snap Setting
Use the four-way controller (23) to select [Vertical Snap]. Press the four-way controller (5).
The [Vertical Snap] screen appears.
Vertical Snap Snaps vertical shots like a cellphone, using OK button On Cancel
Taking Pictures of Dark Scenes (Night Scene/ Night Scene Portrait/Digital SR/Fireworks/ Candlelight Mode)
You can choose settings appropriate for taking pictures of dark scenes, such as nightscapes.

A B c S U

Night Scene

Night Scene Portrait

Digital SR Fireworks Candlelight
For night time images. Use of a tripod or other support is suggested. For images of people at night. Use of a tripod or other support is advised. If you use the Face Recognition function when the flash mode is set to , (Auto), the flash mode automatically changes to d (Flash On + Red-eye). Higher sensitivity reduces blur. The sensitivity is automatically set to Auto and the number of recorded pixels is fixed at f (25921944). For capturing fireworks. Use of a tripod or other support is suggested. The sensitivity is fixed at its minimum setting. For capturing scenes in candlelight.

White Balance

Adjust
The white balance is automatically adjusted.
The setting is saved and the [A Rec. Mode] menu reappears.

Setting the AE Metering

You can set the area of the screen where the brightness is metered to determine the exposure.
Multi-segment metering Center-weighted metering Spot AE metering
The camera divides the image into 256 areas, meters the brightness and determines the exposure. The camera takes a reading of the overall brightness of the picture with the center of the image having more influence on the exposure. The camera determines the exposure by metering the brightness only at the center of the image.
Use the four-way controller (23) to select [AE Metering]. Press the four-way controller (5).
Use the four-way controller (23) to select the AE Metering setting.
Pixel Track SR Recorded Pixels 12M White Balance AWB Focusing Area AE Metering Sensitivity
When the shutter release button is pressed halfway, the brightness is metered and the exposure is determined. When the subject is outside the focusing area and you want to use N (Spot AE metering), aim the camera at the subject and press the shutter release button halfway to lock the exposure, then compose your picture again and press the shutter release button fully. Depending on the selected shooting mode, the AE metering setting may not be changed. Refer to Functions Available for Each Shooting Mode (p.228) for details. If you change the [AE Metering] setting frequently, you can save time by assigning it to the Green button (p.121). Saving the AE Metering setting 1p.127

Setting the Sensitivity

You can select the sensitivity to suit the brightness of the surroundings.
Auto The sensitivity is automatically adjusted by the camera. (Sensitivity 64 - 800) 64 The lower the sensitivity, the less noise that affects the image. The 100 shutter speed will be slower in low light conditions. Higher sensitivity settings use faster shutter speeds in low light 3200 conditions to reduce camera shake, but the image may be affected by noise. 6400
Use the four-way controller (23) to select [Sensitivity]. Press the four-way controller (5).
Use the four-way controller (23) to change the sensitivity.
Rec. Mode Pixel Track SR Recorded Pixels White Balance Focusing Area AE Metering Sensitivity

1/4 Auto 200 400

The image is magnified around the face first recognized when the image was taken.
If multiple faces were recognized when the image was taken, the subjects faces are zoomed up on each time the I button is pressed in order of the recognition during shooting.
Available operations during Face close-up playback mode
Zoom lever to the right (y) Zooms up on the subject being displayed for Face close-up playback at an equal or slightly larger magnification ratio. Zooms up on the subject being displayed for Face close-up playback at an equal or slightly smaller magnification ratio.
Zoom lever to the left (f)
Face close-up playback is not available for images that are saved as still pictures from the movies or images registered in the FAVORITE folder. The magnification ratio for Face close-up playback may differ depending on the conditions such as the size of the face recognized when shooting.
Deleting Images and Sound Files
You can delete images and sound files that you do not want to keep. When images or sound files are inadvertently deleted
Deleted images and sound files can be recovered with the Optio P80 (p.151). Deleted images and sound files can be recovered even if the camera has been turned off after deletion as long as the SD Memory Card has not been removed. However, deleted images and sound files cannot be recovered after operations to write data such as taking pictures, recording movies, protecting images, saving DPOF settings, resizing images, cropping images, registering images as Favorites, deleting images saved as Favorites, or formatting has been performed.

Deleting a Single Image

You can delete a single image or sound file.
Protected images and sound files cannot be deleted (p.152).
Q button Four-way controller 4 button i button
In Q mode, use the four-way controller (45) to choose the image/sound file you want to delete. Press the i button.
A confirmation screen appears.
Use the four-way controller (23) to select [Delete].
The image or sound file is deleted.

The cropped image is saved with a new file name. The number of recorded pixels is selected automatically according to the size of the cropped section.
Processing Images So That Faces Look Smaller
Images are processed to reduce the size of peoples faces detected with the Face Recognition function (p.72) when taking pictures so that they look smaller.
In Q mode, use the four-way controller (45) to choose the image you want to edit. Press the four-way controller (3).
Use the four-way controller (2345) to select N (Small Face Filter).
Face recognition frames for faces that can be corrected are displayed. Proceed to Step 6 when there is only one recognition frame.
Use the four-way controller (2345) to select a face to be processed.
A green frame indicates the face that is to be processed.
Press the 4 button. Use the four-way controller (45) to change the reduction ratio.
F G H Approx. 5 % Approx. 7 % Approx. 10 %
The camera returns to Q mode and the processed image is displayed.
You may not be able to process images in the following situations: - When the size of face taken in relation to an image is too large or too small - When faces are located in the edges of an image In such cases, the face recognition frame in Step 4 will not appear.
Using the Digital Filters
This function lets you change the color tones and perform special processing on a selected image.
B&W Sepia Toy Camera Processes the image into one that has the look of a black and white photograph. Processes the image into one that has the look of a sepia photograph. Processes the image that looks as though it was shot with a toy camera. Processes the image into one that has the look of an old photo.

Retro Color

Processes the image using the selected color filter. You can choose from six filters: red, pink, purple, blue, green, and yellow. Extracts only a specific color and processes the rest of the image Color extraction into black and white. You can choose from three filters: red, green, and blue. There are four filters: Sky Blue/Fresh Green/Delicate Pink/Autumn Color enhancer Leaves. Soft Brightness Processes the image into a soft image that appears soft overall. Adjusts the brightness of the image.

Refer to Steps 7 and 8 in Printing a Single Image (p.176) for details of how to make the settings.
Applies DPOF settings to all images Copies Date Date
The settings for all the images are saved and the DPOF setting method selection screen reappears.
The number of copies specified in the [All Images] setting applies to all the images. Before printing, check that the number is correct. Settings for single images are canceled when settings are made with [All Images].
Recording Sound (Voice Recording).. 180 Adding a Voice Memo to Images. 184
Recording Sound (Voice Recording)
You can record sound with the camera. The microphone is located on the front of the camera. When recording sound, aim the camera at the sound source to obtain the best sound quality.

Microphone Speaker

Setting the Voice Recording Function
6 Recording and Playing Back Sound
To use the Voice Recording function, assign it to the Green button first.
Use the four-way controller (23) to select [Voice Recording] and press the 4 button.
Green Button Q Voice Recording
The Voice Recording function is assigned to the Green button.

Recording Sound

The camera enters the Voice Recording mode. The remaining recordable time and the recording time of the current file appear on the display. 1 Recording time 2 Remaining recordable time

01:31:44

00:00:00

01:30:22 REC

Recording starts. The self-timer lamp blinks 00:01:22 during recording. You can record sounds continuously for up Index to 24 hours. SHUTTER Stop When the Green button is pressed during recording, an index is added to the current sound file.
If you press and hold down the shutter release button for more than one second in Step 2, recording continues until you take your finger off the button. This is useful for recording short sound. The sound is saved in WAVE monaural files.

Playing Back Sound

You can play back the sound files you made in Voice Recording.

Use the four-way controller (2345) to select the language.
The menus and messages are displayed in the selected language.
Changing the Naming Rule of the Folder
You can change the naming rule of the folder for storing images. When the naming rule is set to the date, pictures are saved in separate folders by the date they were taken.
Standard Date xxxPENTX (where xxx is the 3-digit folder number) xxx_mmdd (3-digit folder number_month day) * xxx_ddmm (3-digit folder number_day month) when the [Date Format] is set to [dd/mm/yy]
Taken with the folder Taken with the folder name setting [Standard]. name setting [Date]. (e.g. September 25) (e.g. September 25)
DCIM 100 100PENTX DCIM 100 100PENTX 101 101_0925
Up to 999 folders can be created. Up to 9999 images or sounds can be saved in a folder.
Next time, taken with the folder name setting [Date] again. (e.g. October 1)
DCIM 100 100PENTX 101 101_102_1001
Use the four-way controller (23) to select [Folder Name]. Press the four-way controller (5).
Use the four-way controller (23) to select [Standard] or [Date]. Press the 4 button.
Changing the Video Output Format
When you connect the camera to AV equipment, choose the appropriate video output format (NTSC or PAL) for taking and playing back images.
Use the four-way controller (23) to select [Video Out]. Press the four-way controller (5).
Use the four-way controller (23) to select a video output format.
Choose the video output format to match the input format of the AV equipment.
Setting Video Out Brightness Level Power Saving Auto Power Off Reset Delete All

2/3 NTSC PAL 5sec. 3min.

Depending on the country or region, images and sound files may fail to be played back if the video output format is set differently from the one in use there. If this happens, change the video output format setting. Connecting the Camera to AV Equipment 1p.155 Video output format of each city 1p.239
Adjusting the Brightness of the Display
You can adjust the brightness of the display.
Use the four-way controller (23) to select [Brightness Level]. Use the four-way controller (45) to adjust the brightness.

F G H Dark Normal Bright

Setting NTSC Video Out Brightness Level 5sec. Power Saving Auto Power Off 3min. Reset Delete All

MENU Cancel Exit

The camera returns to A mode or Q mode. The display appears with the set brightness.
Using the Power Saving Function
You can save battery power by setting the display to dim automatically when no operation is performed for a fixed time. After the power saving function has been activated, the display returns to the ordinary brightness if any button is pressed.
Use the four-way controller (23) to select [Power Saving]. Press the four-way controller (5).
Use the four-way controller (23) to select the time until the camera enters power saving mode.
Choose from [2min.], [1min.], [30sec.], [15sec.], [5sec.] or [Off].
2/3 2min. 1min. 30sec. 15sec. 5sec. Off
Power Saving does not function in the following situations: - While taking pictures in j (Continuous Shooting) mode - In the playback mode - While recording a movie - While the camera is connected to a computer - When using the AC adapter - While a menu is being displayed When no operation is performed after the camera is turned on, Power Saving is activated only after 15 seconds elapse even if [5sec.] is set.

Setting Auto Power Off

You can set the camera to turn off automatically when no operation is performed for a fixed time.
Use the four-way controller (23) to select [Auto Power Off]. Press the four-way controller (5).
Use the four-way controller (23) to select the time until the camera turns off automatically.
Choose from [5min.], [3min.] or [Off].
2/3 NTSC 5sec. 5min. 3min. Off
Auto Power Off does not function in the following situations: - While recording sound in Voice Recording mode - While taking pictures in j (Continuous Shooting) mode - While recording a movie - During a slideshow or movie/sound playback - While the camera is connected to a computer In O (Vertical Snap) mode, the camera turns off after 5 minutes regardless of the Auto Power Off setting.
Changing the Start-up Screen
You can choose the start-up screen displayed when the camera is turned on. You can choose any of the following images as the start-up screen: - The Guide Display Start-up Screen showing a guide to the shooting modes and buttons - One of the 3 Optio logos - One of your own images (compatible images only)

By installing the software included on the provided CD-ROM on your computer and connecting the camera to your computer with the USB cable, you can transfer images and movies captured with your camera to the computer and then display and manage them. This section explains how to install the provided software and the other necessary preparations for enjoying the captured pictures and movies on your computer.

Provided Software

The following software is included in the provided CD-ROM (S-SW87). Windows Image viewing/managing/editing software ACDSee for PENTAX 3.0 (Nine languages: English, French, German, Spanish, Italian, Russian, Chinese [traditional and simplified], Korean, and Japanese) Macintosh Image viewing/managing software ACDSee 2 for Mac (Six languages: English, French, German, Spanish, Italian, and Japanese)
It is recommended to use the optional AC adapter kit K-AC88 when the camera is connected to a computer (p.35). If the battery runs out of power while images are being transmitted to a computer, the data may be lost or damaged.
8 Connecting to a Computer

System Requirements

The following system requirements must be met for you to fully enjoy the images and movies captured with the camera on your computer. Windows
OS Windows 2000, Windows XP or Windows Vista The OS must be preinstalled and updated to the latest version. Pentium III or higher (Pentium 4 or higher recommended) 256 MB minimum (1 GB or more recommended) 100 MB minimum (1 GB or more recommended) CD-ROM drive USB port as standard equipment Internet Explorer 5.0 or later DirectX 9.0 or later and Windows Media Player 9.0 or later (for playing movies)
CPU Memory Hard Disk Space Others
* Operation is not guaranteed on all computers meeting the system requirements. * The system requirements describe the minimum environment for playing and editing movies. Windows 95, Windows 98, Windows 98SE, Windows Me and Windows NT are not supported. The versions of Internet Explorer, Windows Media Player and DirectX required for using ACDSee for PENTAX 3.0 are not included in the provided CD-ROM. Visit the following sites to download the necessary items and install/update them on your computer. Internet Explorer http://www.microsoft.com/windows/products/winfamily/ie/ default.mspx Windows Media Player http://www.microsoft.com/windows/products/winfamily/mediaplayer/ default.mspx DirectX http://www.microsoft.com/windows/directx/default.mspx

E Favorites pane You can add frequently used items (folders, etc.). F File List pane Displays the contents of the selected folder or the results of the most recent search (the file or folder that matches the search item). It is the only pane that always appears in the browser and it cannot be hidden or closed. G Status bar Displays information and properties for the selected file.
The selected image is displayed. You can enlarge/reduce the display size of the image.
Details on How to Use ACDSee 2 for Mac
You can find more information on how to use ACDSee 2 for Mac by using the help pages.
Select [ACDSee 2 for Mac] from [Help] on the menu bar.

Click the desired topic.

Functions Available for Each Shooting Mode.. 228 Messages.. 230 Troubleshooting.. 232 Default Settings.. 234 List of World Time Cities. 239 Optional Accessories.. 240 Main Specifications.. 241 WARRANTY POLICY. 245 Index.. 251
Functions Available for Each Shooting Mode
z: Can be set. : Cannot be set.
Shooting Mode Function Zoom lever Zoom operation Face Priority On I button Smile Capture Face Priority Off , (Auto) a (Flash Off) b (Flash On) Flash Mode c (Auto + Red-eye) d (Flash On + Red-eye) b (Soft Flash) 9 (Standard) g (Self-timer) Drive Z (2 sec. Self-timer) Mode j (Continuous Shooting) K (Burst Shooting) = (Standard) q (Macro) Focus 3 (Pan Focus) Mode s (Infinity) \ (Manual Focus) Pixel Track SR/Movie SR Recorded Pixels White Balance Focusing Area AE Metering [A Rec. Sensitivity EV Compensation Mode] menu D-Range Setting Blink Detection Sharpness Saturation Contrast Date Imprint *1 *2 *3 *4 *5 *6 *7 Intelligent Zoom is not available Zoom operation using the fourway controller Only optical zoom is available Digital Zoom is not available Switch with the Green button Fixed at a Fixed at 9

z z z z z z z z z z

z z z z z z z z z z z z

z*1 z z z z z z

*2 z z z*5 z*5 z*7 *8 *11 z*15 *20 *21 *23 *24 z*27 *11

Shutter Speed Built-in Flash
Drive Modes Self-timer Time Function Power Source Battery Life
Interfaces Video Output Dimensions

Weight Accessories

Approx. 1 second - until built-in memory or SD Memory Card is full (however, maximum size is limited to 2 GB) 1/1000 sec. - 1/4 sec., max. 4 sec. (Night Scene mode) Modes Auto, Flash Off, Flash On, Auto + Red-eye, Flash On + Red-eye, Soft Flash Flash Range Wide-angle: approx. 0.2 m - 4.6 m (approx. 0.66 ft - 15.09 ft) (Sensitivity: in Auto condition) Telephoto: approx. 0.5 m - 2.1 m (approx. 1.64 ft - 6.89 ft) (Sensitivity: in Auto condition) Single-frame, Self-timer (approx. 10 sec., approx. 2 sec.), Continuous, Burst Shooting Electronic control type, control time: Approx. 10 sec., 2 sec. World Time 75 cities (28 time zones) Rechargeable lithium-ion battery D-LI88, AC adapter kit (optional) Number of * Recording capacity shows approximate number Recordable of shots recorded during CIPA-compliant testing Images (with display on, flash used for 50% of the shots, approx. 200 and 23 degrees centigrade). pictures Actual performance may vary according to operating conditions. Playback Time * According to the result of in-house testing. approx. 200 min. Actual time may differ depending on usage conditions. Movie Recording Time approx. 70 min. Sound Recording Time approx. 250 min. USB 2.0 (high-speed compatible) /PC/AV terminal NTSC/PAL (monaural) Approx. 97 (W) 54 (H) 21.5 (D) mm (excluding operating or protruding parts) Approx. 105 g (excluding battery and SD Memory Card) Approx. 120 g (including battery and SD Memory Card) Rechargeable lithium-ion battery, battery charger, AC plug cord, USB cable, AV cable, software (CD-ROM), strap, Operating Manual, Quick Guide
Continuous Recording Time

WARRANTY POLICY

All PENTAX cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for a period of twelve months from date of purchase. Service will be rendered, and defective parts will be replaced without cost to you within that period, provided the equipment does not show evidence of impact, sand or liquid damage, mishandling, tampering, battery or chemical corrosion, operation contrary to operating instructions, or modification by an unauthorized repair shop. The manufacturer or its authorized representatives shall not be liable for any repair or alterations except those made with its written consent and shall not be liable for damages from delay or loss of use or from other indirect or consequential damages of any kind, whether caused by defective material or workmanship or otherwise; and it is expressly agreed that the liability of the manufacturer or its representatives under all guarantees or warranties, whether expressed or implied, is strictly limited to the replacement of parts as hereinbefore provided. No refunds will be made on repairs by non-authorized PENTAX service facilities. Procedure During 12-month Warranty Period Any PENTAX which proves defective during the 12-month warranty period should be returned to the dealer from whom you purchased the equipment or to the manufacturer. If there is no representative of the manufacturer in your country, send the equipment to the manufacturer, with postage prepaid. In this case, it will take a considerable length of time before the equipment can be returned to you owing to the complicated customs procedures required. If the equipment is covered by warranty, repairs will be made and parts replaced free of charge, and the equipment will be returned to you upon completion of servicing. If the equipment is not covered by warranty, regular charges of the manufacturer or of its representatives will apply. Shipping charges are to be borne by the owner. If your PENTAX was purchased outside of the country where you wish to have it serviced during the warranty period, regular handling and servicing fees may be charged by the manufacturers representatives in that country. Notwithstanding this, your PENTAX returned to the manufacturer will be serviced free of charge according to this procedure and warranty policy. In any case, however, shipping charges and customs clearance fees to be borne by the sender. To prove the date of your purchase when required, please keep the receipt or bills covering the purchase of your equipment for at least a year. Before sending your equipment for servicing, please make sure that you are sending it to the manufacturers authorized representatives or their approved repair shops, unless you are sending it directly to the manufacturer. Always obtain a quotation for the service charge, and only after you accept the quoted service charge, instruct the service station to proceed with the servicing.